User`s Manual
Contents
1. zero 0 of peeling position and the peeling position shifts front or back by the parameter of each command For details see the separate Command Reference lt Each command initial value gt Emulation DM4 68 6 mm 2 70 in Emulation DMI 12 7 mm 0 50 in Emulation DPP 37 1 mm 1 46 in Example of making fine adjustments STX f nnn When the emulation is set to DM4 the peeling position shifts from zero 0 to frontward position by 0 01 inch In this case the command is STX f 271 The distance between the peeler sensor or platen center and the peeling position is shown below Middle point between labels 35 4 mm 1 39 in Label 10 76 mm 0 42 in 24 64 mm 0 97 in Liner a f A Sensor position Peeling plate Center of platen Note The measurements shown here are examples 3 How to operate 3 5 Peeler commands 3 5 Peeler commands The following are the peeler commands For details of each command see the separate Command Reference Peeling position designated command STX f STX Kf This command designates the feeding amount from the reference point to the peeling position Software switch setting command STX V The peeler function can be temporarily turned ON or OFF by transmitting this command to the printer while turning on the power to the printer Note If the label is at peeling position when the peeler function is selected the medi2. 1 Outline This peeler unit is designed to automatically remove the label from the liner 2 Exterior view and part names Peeling Sensor Door Closed Door Open 7 Inside of the peeler unit 3 How to operate 3 1 Peeler door opening closing 3 2 Media loading 3 3 Peeler setting 3 Howto operate 3 1 Peeler door opening closing Opening Shift the release knob of the peeler to the left with the finger and the peeler door will open Closing Push up the peeler door until it clicks closed 3 2 Media loading D First peel off the labels with a length of 12 cm 5 inch or more on the top of the loading media then load the media into the peeler where the first label comes to the peeling sensor Close the print head of the printer 2 Open the peeler door and pass the liner between the peeling roller and the peeler door and close the door 3 3 Peeler setting To use this peeler select the peeler function from the menu stored in a nonvolatile memory in the printer To change the setting item in a memory execute it in the VuePrint mode that is the menu setting contents printing Note For details about the VuePrint mode see the user s manual of the printer CD ROM The CL S6621 has the menu AutoConfigure set to ON when shipping from the factory In this ON condition if the peeler is installed on the printer the menu Function Select will be automatically changed to Peel On But if the Off condition occur
3. EN SYSTEMS JAPAN CO LTD 6 1 12 Tanashi cho Nishi Tokyo shi Tokyo 188 8511 Japan Tel 81 0 42 468 4608 Fax 81 0 42 468 4687 http www citizen systems co jp PXZ00086 00 PMC 1301
4. PEELER USER S MANUAL Black PPN10003 PEELER USER S MANUAL For CL S6621 Contents CAUTI N ME UOI S 2 Exterior view and part names tae een 3 HOWTO OPO ate sa Soir rtt d Peter nte Erie eee ERO rt i ep Eo ER Ie ute Ub sere een 3 1 Peeler door opening closing sennoina 3 2 Media loadil s entere nets iere tete anun 3 3 Peelet setting secet Remise 3 4 Initial value of peeling position usnesseesssennsssennsssennsssennsssunnsssennsssonnessennnssonnsssenesssnnnssen 3 5 Peeler commands u u nennen 4 Peelet SpecifiCatiOris aeterne died RIDE rive tee eise inet Caution Always use the peeler with the door closed except when the media is loaded into the peeler Do not push down the door roughly when it is opened which may cause damage to the hinge of the door Use the media that meets standard requirements If not the liner and label may be jammed in the peeler Wipe off dirt or glue stuck to the peeler with a soft cloth soaked in a neutral detergent Do not use volatile liquids such as benzine and thinner which may cause the roller rubber and plastic parts to deteriorate CITIZEN is a registered trademark of CITIZEN HOLDINGS CO Japan CITIZEN es una marca registrada de CITIZEN HOLDINGS CO Jap n Company names and product names in this manual are trademarks or registered trademarks of relevant companies Copyright 2013 by CITIZEN SYSTEMS JAPAN CO LTD 4
5. al will not feed even if the Feed key is pressed In this case remove the label first 4 Peeler specifications 4 Peeler specifications Width of liner a Minimum length of label b Minimum width of label c Maximum width of label Thickness of label Thickness of liner Inner diameter of roll media Durability Peeling position accuracy 1 97 7 in 50 177 8 mm Tin 25 4 mm Label fine media Thickness 0 09 mm including glue layer Rolled inwards Label must be positioned at 1 4 in 10 16 mm from left edge of liner which is viewed from front of media exit To be narrower than liner 0 0067 in 0 17 mm or less 0 0027 in 0 07 mm or less 3in 76 mm or more 20 km or 200 000 peeled labels when using the label above 1 5 mm Peeling position varies depending on the type of media the size of roll media and the size of ink ribbon so adjust it to the optimum condition as needed a liL Direction of media feed 11 CITIZEN SYSTEMS AMERICA CORPORATION 363 Van Ness Way Suite 404 Torrance CA 90501 USA Tel 310 781 1460 Fax 310 781 9152 http www citizen systems com CITIZEN SYSTEMS EUROPE GmbH Mettinger Strasse 11 Park House 643 651 Staines Road D 73728 Esslingen Feltham Middlesex TW14 8PA Germany United Kingdom Tel 49 0 711 3906 400 Tel 44 0 20 8893 1900 Fax 49 0 711 3906 405 Fax 44 0 20 8893 0080 http www citizen europe com CITIZ
6. s select the Peel On in the following manner For details of menu setting refer to the operation manual of each printer E Setting the peeler function in the menu setup mode D Prior to entering the menu mode load media into the printer For details about the media loading see the user s manual of the printer 2 Hold in the MODE REPEAT key and at the same time turn on the power to the printer and the printer will be placed into the menu mode where the PRINT LED and the CONDITION LED will light up 3 In the VuePrint mode performs the printing of menu setting contents until the sub menu FUNCTION SELECT of the After Print shows up In that state select the Peel On 6 3 How to operate 3 3 Peeler setting 3 4 Initial value of peeling position Note After selecting the peeler function feed the media to the peeling position by pressing the FEED key After this the media once printed automatically advances towards the peeling position and there the label is peeled off 3 4 Initial value of peeling position If the peeler function is selected when the power is turned on or the resetting is performed the media will automatically feed from the reference point to the peeling position by initial value of feeding amount regardless of printer emulation To finely adjust the peeling position transmit the command STX f or STX Kf from the host computer to the printer In this case each command initial value being set designates the
Download Pdf Manuals
Related Search