EUROPOWER PMP1680S/PMP980S/PMP960M
Contents
1. User Manual EUROPOWER PMP1680S PMP980S PMP960M 1 600 Watt 10 Channel Powered Mixer with Dual Multi FX Processor and FBQ Feedback Detection System 900 Watt 10 Channel Powered Mixer with Dual Multi FX Processor and FBQ Feedback Detection System 900 Watt 6 Channel Powered Mixer with Multi FX Processor and FBQ Feedback Detection System behringer com behringer 2 EUROPOWER PMP1680S PMP980S PMP960M User Manual HE Table of Contents Thank you 2 Important Safety Instructions 3 Legal Disclaimer cur0ur00us0ossnsonssnnsonsnnnsonsonnsonsonnnnnnne 3 Limited Warranty 4 eere eese eerte eene enses ntn atn 3 1 Before you get Started eee 5 TI 5 1 2 Initial operation eese tenente ttnnntnnnis 5 1 3 Online registration entente 5 TA ThieitiiatYdall sustento 5 2 Control eese eee eene enean 7 2 1 Mono and stereo channels 7 2 2 Effects SECTION 7 2 3 Main and monitor section 7 2 4 Rear panel caet eet en RE 8 3 Digital Effects 5 5 9 4 Installation ec2. Type XLR electronically balanced input circuit Mic E I N 20 Hz 20 kHz Type RCA mono output 0 Ohm source resistance 112 dB 114 dB A weighted Impedance approx 1 kOhm 50 Ohm source resistance 112 dB 114 dB A weighted Max input level 21 dBu 150 Ohm source resistance 112 dB 114 dB A weighted Frequency response lt 10 Hz 200 kHz 1 dB Type 14 TRS connectors unbalanced Ol Impedance approx 150 Ohm unbalanced Gain 30 dB 10 dB with pad Max input level 21 dBu Max input level 12 dBu 10 dB gain Type RCA ne m te sori Signal to noise ratio 110 dB 114 dB A weighted MING un Noise THD 0 001 0 0007 A weighted N i e MAIN MIX 20 102 dB 106 dB A weighted Type 14 TS connectors balanced Channel fader o0 Impedance approx 20 kOhm balanced e T ak Mennene zu MAIN MIX 0 dB 84 dB 86 dB A weighted anne fader Type 14 TRS connectors unbalanced Type Neutrik Speakon compatible connector Impedance approx 100 kOhm unbalanced Load impedance Max input level 21 dBu MAIN L R 4 80hm quaier MONITOR MAIN MONO 4 80hm 80 Hz 15 dB MAIN MONO MAIN MONO 4 80hm Mid 2 5 kHz 15 dB High 12 kHz 15 dB DSP PEUT a Type RS Dynamics D A 90 dB Impedance approx 10 kOhm Sampling rate 40 kHz Delay Time max 5 secs MAIN Signal run time approx 1 5 ms Type 14 TS connectors unbalanced Line In gt Line Out
3. cold ve For connection of balanced and unbalanced plugs ring and sleeve have to be bridged at the stereo plug Fig 4 2 4 TRS connector Balanced use with XLR connectors input 1 ground shield 2 hot ve 3 cold ve output For unbalanced use pin 1 and pin 3 have to be bridged Fig 4 3 XLR connectors 10 EUROPOWER PMP1680S PMP980S PMP960M User Manual Please be sure to only use professional locking style speaker cables type NLAFC Please check the pin connections of your loudspeakers and cables depending on connector the EUROPOWER speaker output you choose 4 strain relief cl lt q OUPUTA 1 2 2 MAIN L POS NEG 4 tip MON POS NEG OUTPUT POS NEG OUTPUT 1 1 2 2 4 sleeve MAINR POS NEG pole 1 ground MONO POS NEG BRIDGE POS NEG pole 2 OUTPUT A 1 1 2 2 The footswitch connects both poles momentarily MAIN MONO POS NEG J MON POS NEG Fig 4 4 TS connector for footswitch BRIDGE Please use a dual footswitch for the PMP980S PMP1680S so that you hr 2 can enable disable FX 1 and FX 2 independently of each other In this MAIN MONO POS NEG 5 case the tip of the 14 plug controls FX 1 and the ring FX 2 MAIN POS NEG 5 BRIDGE POS NEG Tab 4 1 Pin connections of
4. Bwn Do not block any ventilation openings Install in accordance with the manufacturer instructions 8 Do notinstall near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat behringec com 9 defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Use only attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid AG gt injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen
5. Impedance approx 150 Ohm unbalanced Max output level 21 dBu MONITOR Type 2 digit 7 segment LED Type 14 TS connectors unbalanced Impedance approx 150 Ohm unbalanced Type 2 x 2 digit 7 segment LED Max output level 21 dBu behringer com 14 EUROPOWER PMP1680S PMP980S PMP960M User Manual Dimensions Weight Dimensions H x W x D approx 12 2 5 x 18 Vox 83 5 RMS Q 196 THD sine wave both channels driven approx 315x460x220 mm 8 Ohm per channel 160W 4 Ohm per channel 300W Weight 18 3 4 Ibs 8 5 kg RMS Q 196 THD sine wave bridged mode ENE 8 Ohm 600W Weight 20 3 4 Ibs 9 4 kg Peak Power both channels driven 8 Ohm per channel 260 W Weight 214 s Ibs 9 9 kg 4 Ohm per channel 450 W BEHRINGER is constantly striving to maintain the highest professional standards As a result of these efforts Peak Power bridged mode modifications may be made from time to time to existing productswithout prior notice Specifications and Z 9 z appearance may differ from those listed or illustrated 8 Ohm 900 W PMP1680S RMS Q 196 THD sine wave both channels driven 8 Ohm per channel 300W 4 Ohm per channel 600 W RMS Q 196 THD sine wave bridged mode 80hm 1200 W Peak Power both channels driven 8 Ohm per channel 400W 4 Ohm per channel 800W Peak Power bridged mode 80hm 1600 W PMP1680S 100 120 V 50 60 Hz T10A H250V 220 240 V 50 60 Hz
6. 1 year or otherwise applicable minimum warranty period from the date of purchase of the original product Upon validation of the warranty claim the repaired or replacement product will be returned to the user freight prepaid by MUSIC Group Warranty claims other than those indicated above are expressly excluded PLEASE RETAIN YOUR SALES RECEIPT IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE 2 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase at behringer com under Support and kindly read the terms and conditions of our limited warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 Return materials authorization Legal Disclaimer Technical specifications and appearance are subject to change without notice The information contained herein is correct at the time of printing All trademarks are the property of their respective owners MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colors and specifications may vary slightly from product BEHRINGER products are sold through authorized dealers only Distributors and dealers are not agents of M
7. exclusively at the buyer s expense MUSIC Group or its authorized service center will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification MUSIC Group will return the unit C 0 D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order Authorized BEHRINGER dealers do not sell new products directly in online auctions Purchases made through an online auction are on a buyer beware basis Online auction confirmations or sales receipts are not accepted for warranty verification and MUSIC Group will not repair or replace any product purchased through an online auction 5 Warranty transferability This limited warranty is extended exclusively to the original buyer customer of authorized retail dealer and is not transferable to anyone who may subsequently purchase this product No other person retail dealer etc shall be entitled to give any warranty promise on behalf of MUSIC Group 6 Claim for damage Subject only to the operation of mandatory applicable local laws MUSIC Group shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind In no event shall the liability of MUSIC Group under this limited warranty exceed the invoiced value of the product 7 Limitation of liability This limited warranty i
8. into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection 16 Where the MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable Limited Warranty 1 Warranty This limited warranty is valid only if you purchased the product from a BEHRINGER authorized dealer in the country of purchase A list of authorized dealers can be found on BEHRINGER website behringer com under Where to Buy or you can contact the BEHRINGER office closest to you MUSIC Group warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one 1 year from the original date of purchase see the Limited Warranty terms in 4 below unless a longer minimum warranty period is mandated by applicable local laws If the product shows any defects within the specified warranty period and that defect is not excluded under 4 MUSIC Group shall at its discretion either replace or repair the product using suitable new or reconditioned product or parts In case MUSIC Group decides to replace the entire product this limited warranty shall apply to the replacement product for the remaining initial warranty period i e one
9. of the power mixer Loudspeaker OUTPUT B 9805 16805 Depending on the operating mode selected see C8 either the right main signal the mono main signal or the bridged mono signal is provided at OUTPUT B PMP960M Either the main or the bridged main mono signal is provided at OUTPUT see 8 When you use a cable with the normal pin connections pins 1 1 it is possible in MAIN MAIN BRIDGE mode to take the mono main signal from this output not bridged Please also refer to chapter 4 3 Loudspeaker connection In BRIDGE mode always connect only one loudspeaker with an impedance of at least 8 0 to OUTPUT B pins 1 2 Please note that OUTPUT A must NEVER be used in BRIDGE mode with pin connections 1 2 Inallotheroperating modes the minimum impedance of the speaker connected must not fall below 4 0 Information on how to properly connect your speaker with regard to polarity can be found on the rear of the mixer PINOUTs SERIAL NUMBER 9 EUROPOWER PMP1680S PMP980S PMP960M User Manual 3 Digital Effects Processor 24 BIT MULTI EFFECTS PROCESSOR This built in effects module produces high grade standard effects such as reverb chorus flanger delay and various combination effects The integrated effects module has the advantage of requiring no wiring This way the danger of creating ground loops or uneven signal levels is eliminated at the outset completely simplifying the handling The
10. the mono channels It determines the relative volume of the left and right input signals before they are routed to the stereo main output The PMP960M has no stereo channels and hence no BAL control because it is a dual mono power mixer The LEVEL control adjusts the channel signal level in the main mix 2 1 1 Input section 3 The CLIP LED is very useful to control the input gain It should never be constantly illuminated only with signal peaks 0 The PAD switch reduces the input sensitivity of the channel by approx 30 dB to connect for example line level signals CD The balanced HI Z input 14 TRS can be used for line level signal sources e g keyboards electric guitars and basses Each channel has a balanced LOW Z microphone input with XLR connectors which also supply the 48 V phantom power for condenser microphones see 27 Unbalanced stereo line inputs with 74 connectors for stereo channels 7 to 10 of the PMP980S PMP1680S They can be used for connecting keyboards with stereo outputs or stereo drum machines Please remember to use either the microphone or the line input of a channel at a time but never both at the same time 2 2 Effects section List of all multi effects presets LED level meter of the effects processor Since the PMP980S PMP 1680S allows you to select two effects simultaneously it also has two level meters DUAL FX Be sure that the clip LED illuminates for signal peaks only If it is ill
11. your purchase by visiting http behringer com and read the terms and conditions of our warranty carefully Should your BEHRINGER product malfunction it is our intention to have it repaired as quickly as possible To arrange for warranty service please contact the BEHRINGER retailer from whom the equipment was purchased Should your BEHRINGER dealer not be located in your vicinity you may directly contact one of our subsidiaries Corresponding contact information is included in the original equipment packaging Global Contact Information European Contact Information Should your country not be listed please contact the distributor nearest you A list of distributors can be found in the support area of our website http behringer com Registering your purchase and equipment with us helps us process your repair claims more quickly and efficiently Thank you for your cooperation 1 4 The manual This manual is designed to give you both an overview of all control elements and to provide detail about how to use them To provide you with a clear structure we have grouped the control elements according to their function They can easily be found on the enclosed numbered illustrations If you need more detailed information on specific topics please visit our web site behringer com The product related information pages and the Ultranet based glossary explain the relevant audio engineering terminology in full detail 6 EUROPOWER PMP1680
12. 80S PMP980S PMP960M User Manual 2 Control Elements A detailed description of all functions of your power mixer can be found in the following chapters Please also refer to the enclosed sheet with the numbered illustrations to get an overview of the control layout 2 1 Mono and stereo channels 1 The HIGH control in the EQ section governs the high frequency range of the respective channel g Use the MID control to boost or cut the mid range frequencies The LOW control allows you too boost cut the low frequency range With the control you adjust volume of each channel monitor mix o The FX control determines the signal level sent from each channel to the built in effects processor this signal is also present at the FX OUT jack see G2 The 980 1680 has two FX controls FX 1 and FX 2 so that you can use two effects simulteneously Accordingly it also provides two effect Aux paths see 32 Please note that the effects processor signal will be inaudible when the FX RETURN control 27 is set fully counter clockwise 6 For the mono input channels the 9805 16805 has a PAN ORAMA control which determines the position of the channel signal in the stereo main mix The PMP960M has no PAN on the input channels because it is a dual mono power mixer The BAL ANCE control for the stereo channels of the PMP980S PMP1680S corresonds to the PAN control for
13. AIN BRIDGE mode depending on the pin connections of the speaker cables In MAIN MAIN BRIDGE mode power of both outputs is added and provided at OUTPUT B Locking cable pins 1 2 With the normal pin connections Locking cable pins 1 1 a main signal is provided in this mode at OUTPUT A and B not bridged In MON MAIN mode the mixer can also be used as a dual mono amplifier i e OUTPUT A provides the monitor signal while the main signal is present at OUTPUT B Please refer to 44 and 45 as well as chapter 4 4 Loudspeaker connectors 8 EUROPOWER PMP1680S PMP980S PMP960M User Manual In BRIDGE mode always connect only one loudspeaker with an impedance of at least 8 0 to OUTPUT B pins 1 2 Please note that OUTPUT A must NEVER be used in BRIDGE mode with pin connections 1 2 9 Inallotheroperating modes the minimum impedance of the speaker connected must not fall below 4 0 Usethe SPEAKER PROCESSING switch to activate a filter that adapts the mixer to the specifications of your loudspeakers If the speakers have a limited frequency response in the bass range it allows you to adapt it optimally to the frequency response of the speakers If STANDBY is pressed all input channels are muted During breaks you can thus prevent the microphones from picking up noise or interference which would then be reproduced by the P A system The advantage is that all faders can be left untouched while you play a CD via the CD TA
14. AUX IN control adjusts the volume ofthe external signal in the main mix The CD TAPE IN RCA input allows you to feed in external stereo signals e g from a CD player tape deck or other line level source The VOICE CANCELLER filters vocal specific frequencies from the CD TAPE IN signal This function can be used for karaoke i e you can remove the vocals from a song and then sing along with the music yourself UJ I The REC OUT RCA provides line level signals from the power mixer to a DAT recorder for example On the PMP980S PMP16805 the REC OUT signal is Stereo and on the PMP960M two identical mono signals are provided Ifthe REC OUT signal is connected to a recorder whose output signal is returned to the CD TAPE IN feedback can occur when you activate the record function So disconnect the CD TAPE IN from the recorder before you start recording The MAIN 14 connectors allow you to send the main signal to an external amplifier when you only wish to use the mixer and effects section The signal is taken pre power stage of the mixer It is also possible to use only the left jack ofthe output The PMP960M has only one mono output connector behringer com Connect your monitor power amps or active monitor speakers to the mono MONITOR output to monitor the signal mix created with the MON controls orto route it to the musicians on stage Use the POWER switch to put the unit into operation The POWER switch should always be in t
15. NGER but notify your dealer and the shipping company immediately Otherwise claims for damage or replacement may not be granted We recommend that you use a flight case so as to give your power mixer optimum protection during use or transport Always use the original packing carton to prevent damage during storage or transport Make sure that children cannot play unsupervised with the device or its packaging Please ensure proper disposal of all packing materials 1 2 Initial operation Be sure that there is enough air space around the unit for cooling and to avoid overheating please do not place the EUROPOWER near radiators etc Blown fuses must be replaced by fuses of the same type and rating Please refer to the Specifications for details The mains connection is made using the enclosed power cord and a standard IEC receptacle It meets all of the international safety certification requirements Please make sure that all units have proper ground connection For your own safety never remove or disable the ground conductor from the unit or on the AC power cord Important notes concerning installation The sound quality may diminish within the range of powerful broadcasting stations and high frequency sources Increase the distance between the transmitter and the device and use shielded cables for all connections behringer com 1 3 Online registration Please register your new BEHRINGER equipment right after
16. PE inputs see G5 There is also no need to move down the faders of muted channels and lose your mix 2 3 1 Connectors The FOOTSWITCH connector is for a standard footswitch You can activate an effect bypass that mutes the effects processor Please use a dual footswitch for the 9805 16805 so that you can enable disable FX 1 and FX 2 independently of each other In this case the tip of the 4 plug controls FX 1 and the ring FX 2 The FX OUT connector is used to route the FX SEND signal from the input channels for example to the input of an external effects processor The 9805 16805 has two FX controls per input signal see 5 and also two FX OUT connectors FX OUT 1 and FX OUT 2 Please note When you connect a mono plug to one of the FX OUT jacks the signal path from the respective FX send to the built in effects processor is interrupted For each FX send you can either use the built in effect or the corresponding FX OUT jack for an external effect but never both at the same time When you use a stereo plug tip and ring interconnected you can use the built in effects processor and the FX OUT jacks in parallel m c Use the AUX IN 74 inputs to route an external stereo signal to the main mix This can be the signal generated by an external effects processor Use the left input for mono signals which are then reproduced on both stereo sides The PMP960M has only one mono AUX IN connector The
17. S PMP980S PMP960M User Manual Front Panel FE LIROFOLIEF PMP1680S BIG HALL 09 CHURCH a FX PROCESSOF AND FEEDBACK DETECTION SYSTEM 10 SMALL ROOM 13 MID ROOM behringer l T FUE T PHANTOM MONITOR 84 PHASER amp REVERB MASTER 86 PITCH amp REVERB 88 DELAY amp REVERB DELAY amp GATED 91 DELAY amp REVERSE 92 DELAY amp CHORUS 94 DELAY amp FLANGER 38 DELAY amp PHASER 88 DELAY amp PITCH SH MONITOR MON GRAPHIC EG WITH FBG FEEDBACK DETECTION BRIDGE MODE am ON E OFF eoow 600w 2 CH MODE 300 W 8 OHM 600 W 4 OHM 4 OHM MIN LOAD BRIDGE MODE 1200 W 8 OHM 8 OHM MIN LOAD 1 1 i CAUTION DO NOT CONNECT TO OUTPUT A PERES SEE OWNER S MANUAL FOR 1 1 1 1 SPEAKER CONNECTION al 2 SPEAKER 4 8 8 16 1 1 1 17 power purces 7 L FUSE JALUE 411999 L 4 CLASS SERIAL NUMBER COMPLIES WI behringer com 7 EUROPOWER PMP16
18. T6 3A H250V Power consumption 1000 W Mains connector IEC standard receptacle behringer com 15 EUROPOWER PMP1680S PMP980S PMP960M User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION BEHRINGER EUROPOWER PMP1680S PMP980S PMP960M Responsible party name MUSIC Group Services USA Inc Address 18912 North Creek Parkway Suite 200 Bothell WA 98011 USA Phone Fax No Phone 1 425 672 0816 Fax 1 425 673 7647 EUROPOWER PMP1680S PMP980S PMP960M complies with the FCC rules as mentioned in the following paragraph This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more ofthe following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect th
19. USIC Group and have absolutely authority to bind MUSIC Group by any express or implied undertaking or representation This manual is copyrighted No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of MUSIC Group IP Ltd ALL RIGHTS RESERVED 2011 MUSIC Group IP Ltd Trident Chambers Wickhams Cay P 0 Box 146 Road Town Tortola British Virgin Islands 1 Toobtain warranty service please contact the retailer from whom the equipment was purchased Should your BEHRINGER dealer not be located in your vicinity you may contact the BEHRINGER distributor for your country listed under Support at behringer com If your country is not listed please check if your problem can be dealt with by our Online Support which may also be found under Support at behringer com Alternatively please submit an online warranty claim at behringer com BEFORE returning the product All inquiries must be accompanied by a description of the problem and the serial number of the product After verifying the product s warranty eligibility with the original sales receipt MUSIC Group will then issue a Return Materials Authorization number 4 EUROPOWER PMP1680S PMP980S PMP960M User Manual Subsequently the product must be returned in its original shipping carton together
20. and outs recording the mix signal or playing back external signals EUROPOWER 16805 Stereo channel 7 8 Mono channels 1 4 Mono Tape id channel 6 rz Mono WBE channel 5 SEE lt Dat recorder Electric guitar fe Tr en rmm mmm Keyboard Fig 5 3 Standard set up example behringer com One example of how to use your power mixer with a subwoofer in bridged mono mode The illustration shows the PMP 16805 with a subwoofer connected to OUTPUT B that will receive the full bridged output power A separate stereo power amp BEHRINGER EUROPOWER EP2000 for the stereo main P A signal is connected to the Pre Amp Main outputs The Pre Amp monitor output is wired to active speakers on the stage This application can also be realized with the PMP960M except for the main P A signal which would be mono Subwoofer F O H mix MAIN Monitor mix MONITOR i EP1500 EUROLIVE B1220 PRO EUROLIVE B1800X PRO Subwoofer 2 x BEHRINGER B215A active Fig 5 4 EUROPOWER in bridged mono mode 13 EUROPOWER PMP1680S PMP980S PMP960M User Manual 6 Specifications
21. ce eese eene eren erret 9 Mains connection userserssssserseesessssssesnessessersasensssserassessenere 9 4 2 Audio connections rrsseseresserrssesesseresseresseressesesseresseesee 9 4 3 Loudspeaker connection 10 5 Wiring Examples 11 6 SPECIFICATIONS cscnsecscscesscdscienscusssssssoscesesscessssesecsossenss 13 Thank you Thank you for choosing one of the PMP series powered mixers from BEHRINGER These mixers pack impressive features such as digital effects graphic EQs FBQ feedback destroyer and unique voice cancelling function all in a lightweight portable package You now have a versatile combination of inputs routing options effects and power amp operations for your rehearsal space small venue or portable PA needs But why bother with manuals We know you want to get started right away but please read this manual carefully and keep it handy for ongoing reference These instructions show you all the inside features tricks and tips you need to build the best possible sound with your new PMP powered mixer After all it s all about your sound behringer com 3 EUROPOWER PMP1680S PMP980S PMP960M User Manual Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock Use only high quality commercially available s
22. e equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 ofthe FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Important information Changes or modifications to the equipment not expressly approved by MUSIC Group can void the user s authority to use the equipment behringer com We Hear You AN behringer com behringer
23. he Off position when you are about to connect the unit to the mains Please note The POWER switch does not fully disconnect the unit from the mains Unplug the power cord completely when the unit is not used for prolonged periods of time 2 4 Rear panel The mains connection is on a standard IEC receptacle An appropriate power cord is supplied with the unit FUSE HOLDER Before connecting the unit to the mains ensure that the voltage setting matches your local voltage Blown fuses should only be replaced by fuses of the same type and rating Please also read the information given in chapter 6 Specifications Loudspeaker OUTPUT A 9805 16805 Depending on the operating mode selected see 28 either the left main signal or the monitor signal is provided at OUTPUT A Never use this output in bridged mono mode PMP960M In MON MAIN mode the monitor signal is provided at OUTPUT A see 08 Never use this output in bridged mono mode except when you use a cable with the normal pin connections pins 1 1 In this case you can take the mono main signal from this output in MAIN MAIN BRIDGE mode not bridged Please also refer to chapter 4 3 Loudspeaker connection The impedance of the loudspeaker connected must not fall below 4 Q Please note that the power delivered to the speaker in bridged mono mode is considerably higher than in other operating modes Please read the information given on the rear panel
24. loudspeaker connectors tip tip sleeve shield sleeve OUTPUT B OUTPUT B Fig 4 5 RCA cabl d iL ig 4 5 RCA cable JE JR N 1 1 amp 4 3 Loudspeaker connection 3 d Your PMP mixer is equipped with high quality twist lock professional style loudspeaker connectors which ensure safe and trouble free operation 80 1 i 80 This connector was especially developed for high power loudspeakers Once it is 40 40 plugged in it safely locks into position and cannot be accidentally disengaged It prevents the occurrence of electrical shock and ensures the correct polarity BADE Each of the connectors carries only the assigned single signal see tab 4 1 fig 4 7 and the information on the rear panel of the power mixer Maks x N AR 160 Professional speaker connector 9 L 80 compatible with Neutrik Speakon connectors I 2 eg LU Fig 4 7 Connector assignment ne front view rear view Fig 4 6 Professional twist lock style connector behringer com 11 EUROPOWER PMP1680S PMP980S PMP960M User Manual 5 Wiring Examples For stereo operation the POWER AMP switch 28 of the PMP980S PMP1680S must be set to its upper position MAIN L MAIN R Outputs A and B deliver the stereo main signal to the P A speakers Two active speakers wired in parallel are connected to the preamp monitor output They are used as
25. on stage monitor speakers The effects processors can be switched on and off with a dual footswitch This set up is not possible with the PMP960M no stereo operation possible OUTPUT A PMP1680S 2 x BEHRINGER EUROLIVE Stack B1800X amp B1220 both passive Loudspeaker mix T En PMP1680S Front Panel excerpt Dual footswitch 2 x BEHRINGER B215A active Loudspeaker connection monitor mix Fig 5 1 EUROPOWER mixer as a stereo amplifier example behringer com Both the 9805 16805 and the PMP960M can be set up for dual mono operations The POWER AMP switch must be set to its lower PMP960M or center position 9805 16805 The two loudspeaker outputs provide the main and monitor signals independently of each other and to two loudspeakers each which are wired in parallel PMP960M Rear Panel excerpt 2 x BEHRINGER EUROLIVE B1520 2 x BEHRINGER passive EUROLIVE F1520 passive Loudspeaker connection for F O H and monitor mix mono Fig 5 2 EUROPOWER as a dual mono amplifier example 12 EUROPOWER PMP1680S PMP980S PMP960M User Manual This illustration shows just one example of how the channels of your power mixer can be used including the connection of mono and stereo sources and the tape ins
26. ovided for in any enclosed software limited warranty This limited warranty is invalid if the factory applied serial number has been altered or removed from the product Free inspections and maintenance repair work are expressly excluded from this limited warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons guitar strings illuminants and similar parts 6 Damage defects caused by the following conditions are not covered by this limited warranty e improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals e connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used e damage defects caused by acts of God Nature accident fire flood etc or any other condition that is beyond the control of MUSIC Group behringer com Any repair or opening of the unit carried out by unauthorized personnel user included will void the limited warranty If an inspection of the product by MUSIC Group shows that the defect in question is not covered by the limited warranty the inspection costs are payable by the customer 3 Products which do not meet the terms of this limited warranty will be repaired
27. peaker cables with 14 TS plugs pre installed All other installation or modification should be performed only by qualified personnel ATTENTION RISQUE DE CHOC ELECTRIGUE NE PAS OUVRIR gt This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock gt This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual gt Caution To reduce the risk of electricshock do not remove the top cover or the rear section No user serviceable parts inside Refer servicing to qualified personnel gt Caution To reduce the risk of fire or electric shock do not expose this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids such as vases shall be placed on the apparatus gt Caution These service instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions Repairs have to be performed by qualified service personnel gt Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth
28. rack In signal see 65 The MONITOR MASTER control adjusts the monitor output volume Use this 5 digit LED meter to control the output level of the monitor signal The upper LIM LED illuminates when the internal amp protection circuit responds to output levels that are too high The MAIN MASTER control is used to adjust the main output volume Use this 5 digit LED meter to control the output level of the main signal The 9805 16805 has two rows of LED meters L R because the signal is stereo The upper LIM LED illuminates when the internal amp protection circuit responds to output levels that are too high 48 V phantom power is provided for condenser microphones The phantom power supply is activated for all channels with the PHANTOM switch and the PHANTOM LED above the switch illuminates Use the POWER AMP switch to determine the operating mode of your power mixer The PMP980S PMP16805 has three different operating modes In MAIN L MAIN R mode it functions as a stereo amplifier i e the left and right main stereo signals are sent to OUTPUT A L and OUTPUT B R In MON MONO mode it functions as a dual mono amplifier i e OUTPUT A sends the monitor signal and OUTPUT B the main signal mono In BRIDGE AMP MODE the output power of outputs A and B are added and provided at OUTPUT B The PMP960M also has three operating modes since it can be operated in two modes with the switch in its upper position MAIN M
29. s the complete and exclusive warranty between you and MUSIC Group It supersedes all other written or oral communications related to this product MUSIC Group provides no other warranties for this product 8 Other warranty rights and national law This limited warranty does not exclude or limit the buyer s statutory rights as a consumer in any way The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of applicable mandatory local laws This warranty does not detract from the seller s obligations in regard to any lack of conformity of the product and any hidden defect 9 Amendment Warranty service conditions are subject to change without notice For the latest warranty terms and conditions and additional information regarding MUSIC Group s limited warranty please see complete details online at behringer com MUSIC Group Macao Commercial Offshore Limited of Rue de Pequim No 202 A Macau Finance Centre 9 J Macau including all MUSIC Group companies 5 EUROPOWER PMP1680S PMP980S PMP960M User Manual 1 Before you get Started 1 1 Shipment Your PMP mixer was carefully packed at the factory and the packaging is designed to protect the unit from rough handling Nevertheless we recommend that you carefully examine the packaging and its contents for any signs of physical damage which may have occurred during transit Ifthe unit is damaged please do NOT return it to BEHRI
30. se effect presets are designed to be added to dry signals If you move the FX RET control you mix the channel signal dry and the effect signal down the FX controls in those channel strips whose signals you don t wish to process 4 Installation 4 1 Mains connection Blown fuses must be replaced by fuses of the same type and rating The mains connection is made using the enclosed power cord and a standard IEC receptacle It meets all of the international safety certification requirements Please make sure that all units have a proper ground connection For your own safety never remove or disable the ground conductor from the unit or of the AC power cord 4 2 Audio connections The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced TS connectors except for the balanced mono line inputs Of course all inputs and outputs work with both balanced and unbalanced connectors The Tape Ins and Outs are on stereo RCA connectors Please ensure that only qualified personnel install and operate the power mixer During installation and operation the user must have sufficient electrical contact to earth Electrostatic charges might affect the operation of the unit Unbalanced 4 TS connector Strain relief clamp Fig 4 1 74 TS connector behringer com Balanced 4 TRS connector lt strain relief clamp 4 sleeve sleeve ground shield ring
31. uminated all the time it is a sign that the effects processor is overloading and hence producing unpleasant distortion behringer com The Effect display PMP980S PMP1680S two displays shows the currently selected preset Turn the PROGRAM control 9805 16805 one control each for FX 1 and FX 2 to select an effects preset preset number starts flashing Push the control briefly to confirm your selection Press the FX IN button PMP980S PMP1680S FX 1 IN and FX 2 IN to activate the effects processor 2 3 Main and monitor section Your power mixer is equipped with two graphic 7 band equalizers The upper one processes the monitor signal the lower one the main signal Use the EQs to adjust the sound to the room acoustics Press the FBQ IN switch to activate the FBQ Feedback Detection System The frequencies causing feedback are shown by the brightly lit fader LEDs Simply lower the level of the respective frequency range until feedback disappears and the LED goes out Your power mixer offers this function both for the main and the monitor mix 3 Turn the FX RET control to add the effect signal to the main mix lower or monitor mix upper The PMP980S PMP 1680S allows you to use two effects at the same time it also has two FX controls each for the main and monitor mixes when the FX RET 1 and FX RET 2 controls are fully counterclockwise no effect signal is added The CD TAPE IN control adjusts the volume of the 2 T
32. with the return authorization number to the address indicated by MUSIC Group Shipments without freight prepaid will not be accepted 4 Warranty Exclusions This limited warranty does not cover consumable parts including but not limited to fuses and batteries Where applicable MUSIC Group warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety 90 days from date of purchase This limited warranty does not cover the product if it has been electronically or mechanically modified in any way If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship This limited warranty does not cover any such modification adaptation regardless of whether it was carried out properly or not Under the terms of this limited warranty MUSIC Group shall not be held responsible for any cost resulting from sucha modification adaptation This limited warranty covers only the product hardware It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product Any such software is provided AS IS unless expressly pr
Download Pdf Manuals
Related Search