automatic washing machine user manual hwmp70
Contents
1. The cycle indicator lights will go off and the Delay Hours indicator light will be on During the delay program press the Delay button to display the time remaining The delay time indicator shows the time remaining till the wash ends To cancel the delay program switch the power off and back on then make a new selection Delay start 2 24hr option He Delay time is to the end of washing cycle The wash will finish in about 18 hours 12 Installation of drainage hose Install drainage hose First connect the drainage hose to the connection point on the lower back side of the cabinet and fasten with drain hose hoop provided Connect drain hose guide on to the outside of drainage hose To guide the drain hose over the tub or standpipe the hose guide MUST be fitted to the drain hose Drain hose neck guide O Drain hose hoop The height of the standpipe or tub should be between 850 1200 mm To avoid syphoning the drain hose should not extend more than 20 mm from the end of the guide Ensure drainage hose is held in place to avoid leaks or spills Installation of water inlet hoses The new hose sets supplied with the appliance are to be used and that old hose sets should not be reused 1 Insert a new flat washer into each end of the inlet hose 2 Connect the water inlet hose to the water faucet You may have W to use pliers to tighten the coupling Do not over tighten as this2. Specifications Type Fully Automatic Washing Machine Model HWMP60 118 HWMP70 118 HWMP70 118R Rated voltage frequency Rated washing power Rated spinning power 220 240V 50Hz 220 240V 50Hz Net weight Gross weight 39kg 44 5kg Dimensions mm L520 W530 H 900 L550 W560 H955 Water inlet pressure 0 03MPa 1 0MPa when water temperature is 50 C the water inlet pressure of hot water shall not exceed 0 4MPa Note Default settings when you choose this program after power on Wash Rinse Spin Temp Time Normal Long 1 Rinse 7 Min HWMP60 118 9 Min HWMP70 118 HWMP70 118R 10 Warm Cold 103Min HWMP60 1 18 108Min HWMP70 118 HWMP70 118R Heavy Long 2 Rinses 7 Min 6 Warm Cold 76 Min Delicate Rapid 2 Rinses 5 Min 6 Warm Cold 34 Min Quick Express 1 Rinse 3 Min 3 Warm Cold 12 Min Memory This cycle setting remembers the last wash rinse and spin settings Synthetic Medium 1 Rinse 5 Min Warm Cold Wool Express 2 Rinse 3 Min Cold Cold Tub dry 18 AUTOMATIC WASHING MACHINE USER MANUAL This manual is for HWMP60 118 HWMP70 118 HWMP70 118R e Please read this manual carefully before using Retain for future reference 0030509798B CONTENTS Packing list Product o
3. aters a cooking appliances etc ee fs 5 Any floor unevenness may J x eeu ie C Delay button result in unstable working or 3 4 abnormal noise Please ensure The display shows the time remaining in minutes before the cycle will finish the machine is level Push the Delay button and the display will show the remaining time for the cycle to finish in hours The indicator flashes to indicate that the delay function is operating Delay start can be set for 2 24hr operation Check the following before washing NOTE The delay time is until the selected wash program finishes you will need to deduct wash time from this delay time to calculate when the wash will start Check ifthe Clear the pockets Tie any long The weight of the When the machine is laundry has land take out loose straps or strings laundry shall not running buttons may any special items suchas fastenbuttons exceed the rated cause noise To D Water Level button washing coins sand and close capacity of your reduce the noise turn During the Memory and Synthetic programs the washing machine will detect the size Stuns NAlrpins gie oa Henie aed ee varie el of the laundry and automatically select the water level between levels 4 6 8 or 10 the laundry before P y placing it evenly bag To change the water level press the Start Pause button and make your selection in the tub by pressing the Water Level button until d
4. before checking the machine Using diagnostic list below please check if the machine A separate earthed power socket is Ensure the plug is removed and the required for the power supply Hold the plug NOT the electric cable when unplugging the washing machine Do not insert or remove the power plug with wet hands After installation of the washing machine the power plug should be accessible taps turned off in the following cases Power failure cleaning moving installation and when not in use Q not try to fix it yourself Problem The machine does not drain or drains slowly The display shows E1 Possible causes e Is the drain hose blocked requires repair If a repair is required please contact our Customer Care Team do What to do e Remove the blockage Open and close the top lid once If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent Do not install this appliance in a damp or wet environment Do not leave wet laundry on the Control Panel or spray water directly on to this appliance as this may cause the washer to malfunction or cause an electrical fault The openings must not be obstructed by a carpet The ventilation holes at the bottom CAUTION If this appliance is supplied from a cord extension set or electrical portable outlet device the cord extension set o
5. e start pause button is not pushed within 5 minutes the washing machine will automatically switch off the power Button Operation and Descriptions 1 Press the button to switch power on off 2 Press the KOJ button to select automatic program When the power is switched on Normal cycle is automatically set To select a different automatic cycle press the Cycle button till the corresponding indicator is on Refer to the section on the Cycle button above E g choose Quick cycle for a small load of lightly soiled laundry When the Synthetic or Memory cycles are selected the Fuzzy Logic program is run The washing cycle is automatically set while the water level and wash time can be selected according to the texture and size of the load 11 Operation amp Wash Cycles Before washing B Wash Rinse Spin buttons Preparation l 7 E th ter inlet h tly install You may change the Wash Rinse and Spin times when Memory Heavy Normal and rane are nee a ivanell Synthetic cycles are selected Insert the power plug into the electrical socket For Wool program you can select procedure but can not change them Ensure the drain hose is mounted at the correct height For Tub Dry and Quick programs push the Wash Rinse and Spin button the machine Select a suitable location for the washer on a hard even has no reaction surface away from direct sunlight or heat sources e g radiators he
6. esired level is shown 1 10 f there is water inside the tub and the machine cannot detect the laundry load it will display water level 6 If wet laundry is put in the machine it will display level 3 you can then manually adjust to the desired water level A A f Quick program is selected it will display water level 3 you can then manually adjust to the desired water level Lo lt gt You can select water level from 6 to10 for Wool program f Tub Dry program is selected the water level cannot be manually overridden During operation of the wash or rinse program you can adjust the water level by Check if the laundry is suitable for machine washing pressing the Water Level button Divide the laundry into colour fast and non colour fast items The water level may vary due to the different moisture level of the laundry items Separate items that do not absorb water easily and wash by hand For heavily soiled items please first remove loose dirt then apply detergent directly as per instructions on pack to the stain before washing For those items that may attract lint or are furry or fluffy please turn inside out before washing Do not put laundry soiled with chemicals or solvents into the washing machine 10 7 Loading your laundry Operation amp Wash Cycles The rated washing capacity refers to the largest dry weight of a load that can be washed Memory Normal Lon
7. g 3 Rinses 9 Min inutes Remaini Hot Cold Gsynthetic Heavy Medium 2 Rinses Q7Min aa Warm Cold The thickness size and type of clothes will influence the actual capacity Wool Delicate Rapid 1 Rinse 5 Mi a amp Cold Cold Tub dry Quick Express Do not select more than water Level 4 for clothes less than 1 0kg to avoid splashing of water It is recommended that low suds high efficiency washing powder is used Detergent Usage Guide ee Adding washing powder Off On Indicates the program is about to run and indicates the selected cycle and options It is suggested to dissolve detergent before adding to Flashing Indicates the program is running and indicates the selected cycle and options the tub see as below 1 Prepare warm water lt 35 C in a container 2 Add washing powder stirring to dissolve it completely Adding washing powder Fuzzy Logic Programs Add washing powder liquid into the detergent box directly for Fuzzy logic programs and Delay program Adding washing powder Normal Wash It is recommended that washing powder liquid is dissolved with water and then directly emptied into the washing machine j 1 Add some water select the 1 water level How to USE bleachiwhitener 2 Add washing powder liquid Run for about 30 seconds to fully dissolve the detergent Then push the Start Pause button to pause the wash cycle 3 Load laundry Select suitab
8. gram is setting the drain time there will be a pause before the spin program starts e There maybe water in the drain hose when first used e t maybe residual water after performance inspection by the factory 16 Product Overview Top lid Detergent box Balance ring Lint filter Pulsator Drainage hose Control panel Liquid whitener inlet Cabinet Adjustable leg I Back cover Handle Drainconnector Fixed leg Adjustable foot film Description of symbols Cold water valve Power cord 1 SS SJ ECC CALCU CCC CCC S y o SS X S Passi we Ar J Hot water valve G Handle A S Contents marked with this symbol are related to the Warning sign safe use of the product and the personal safety of the user Please operate in accordance to the contents of this manual to avoid harm to the user or damage to the Q machine itself n Contents marked with this symbol indicate operations Forbidd EE or actions that should not be undertaken by the user Performing of such actions may result in injury to the SAFETY WARNING user or damage to machine itself and void warranty Please check power socket condition to ensure it has been earthed correctly prior to installation to ensure your safety Safety Precautions Trouble shooting If there is a fault or the machine does not operate correctly remove the power plug
9. harsh solvents The filter at the water inlet valve may become blocked by impurities in the water supply Clean it with a plastic bristled brush every two months 1 After washing cycle has finshed turn off the water faucet If needed you can remove the water inlet hose 2 Do not store water in the washing machine for a long period without completing a wash cycle Drain the water completely after each wash 3 Hang up the power cord and drain hose 4 Wipe up any drops of water on the surface of the machine and inside the tub Leave the lid open for about 1 hour after each wash to evaporate any residual water 14 Safety precautions Do not attempt to move washing or Do not take apart repair or place hands inside washing machine alter the machine by yourself while in operation Please ensure children are supervised around machine to avoid harm Do not leave hot or heavy items on lid Do not wash laundry with chemicals or control panel as this may cause or other volatile materials Such as damage to the washer or make the petrol solvents or thinners as this washer may cause damage unsafe to to the machine operate This appliance is not intended for use by persons Keep washer away from heat including children with reduced physical sources such as heaters stoves or sensory or mental capabilities or lack of direct sunlight experience and knowledge unless they have been given supervision or instruction co
10. le water level Push the Start Pause button again to recommence washing cycle Remaining time display H Displays during Fuzzy Logic detection cycle until level is determined Displays total time remaining during current in progress wash cycle Displays remaining time when the Delay program is used hours Displays error codes see page 15 Cycle button Program Recommend Normal Recommended for mixed fabrics and general clothing items Items that are soiled or items that are heavy big Delicate Delicate items that are machine washable Quick Lightly soiled or small laundry loads less then 1 5kg This cycle setting remembers the last wash rinse and spin settings Synthetic Ideal for synthetic fabrics Machine washable woollen items Close the lid Tub dry Dries the inner and outer tub to avoid the growth of mildew q you open the lid during spin cycle the machine will stop and an audible p Always refer to the bleach whitener instructions prior to usage Fill water to desired level Dilute the bleach whitener in a container Pour it slowly into the washing tub If you select Quick program it is recommended to use liquid detergent instead of washing powder to ensure the most effective wash results Old or poor quality washing powder may causing caking in tub or detergent dispenser Clean the detergent box periodically to ensure washing power is evenly distributed and remove any detergent b
11. may 7 cause damage to the valve or hose fittings 3 Connect the other ends to their respective cold and hot water inlet valves located on the top of the washer Nut of the water inlet hose Water absorption cushion to Joiner of the water inlet valve 4 Fasten each hose on the washing machine and ensure a tight connection Check the inlet hose connections Swing the hose gently to confirm that the hose is AVA securely fastened 6 After installation open the tap to check for leaks A Do not bend the hose unduly Periodically check the hose connections are firm at both ends This is to ensure the connections remain watertight over time Removing the water inlet hoses 1 Turn off the water taps 2 Loosen each connection at faucet and washer 3 Carefully remove each hose separately as they may contain residual water Operation amp Wash Cycles Press the Temp Wash Rinse button to select your wash temperature During Quick cycle the water temperature is preset Temp button does not work During wool cycle the hot cold water temperature cannot be chosen F START PAUSE button After the power is switched on press the Start Pause button to start the machine During operation push the Start Pause button to pause the machine Push the Start Pause button again to restart the machine G POWER button To turn on off the power press the power button e f th
12. ncerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance f power cord or other parts of this machine become damaged or faulty please contact a technician to have it repaired DO NOT attempt repairs yourself as this may cause personal harm or void warranty Please remove items such as coins Check that water faucets are open buttons sand and other solid materials after connection to machine prior from clothing before washing to operation and that pipes are connected correctly Please use low suds high efficiency washing powder Installation amp Adjustment Please install and adjust the machine according to the directions contained in this manual It is very important to follow these directions for the safe operation of the machine and to ensure your machine operates correctly Install the lint filter After removing washer from outer packaging take out the lint filter from the document bag install it to the inner tub See the figure opposite Please ensure the lint filter is installed correctly and maintained in good condition to ensure the water outlet is not blocked or the flow altered If the lint filter is lost or damaged contact Customer Care Install the bottom plate The purpose of the bottom plate is to suppress noise from the washing machine during operation Steps 1 Lay the washer on it
13. p lid closed e Is the laundry distributed unevenly in the machine e Insert the power plug tightly e Close the top lid e Redistribute the laundry come into contact with water or moisture If you are using an extension cord or a portable electrical outlet device not recommended ensure that it is positioned so that it does not There are abnormal sounds inside the machine e Is the machine level e Has the laundry been placed unevenly in the machine e Are there any foreign objects inside the bowl e Redistribute the load evenly Close the top lid e Level the machine e Remove the foreign object The water tap leaks e Is the water inlet hose loose e Fasten the inlet hose Maintenance Remove the power plug before carrying out any cleaning or maintenance Clean the lint filter s and detergent box after each wash Remove and clean the detergent The lint filter must be used during box replace after cleaning washing t must be cleaned after each use Lint filter 1 Slide upwards to remove 2 Gently push it down to install ensuring it is in place before next wash Dismantle Install Directions for cleaning lint filter on model If the cabinet is dirty wipe it with a damp cloth e Do not wash directly with water e Wipe with a neutral detergent please check directions on detergent bottle first eDo not wipe machine with thinners petrol alcohol or other
14. r electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture Do not connect to hot water higher than 65 C temperature Do not wash water proof clothing as this may affect load balance during spin cycle s The machine stops running The display shows E2 e The top lid is not closed e Close the top lid The machine does not spin The display shows E3 e Has the laundry been place unevenly in the machine e Is the machine level e Redistribute the load evenly Close the top lid e Level the machine The machine will start 10 seconds after being leveled correctly The display shows E4 e Is the water tap closed or has the water supply been interrupted e Is the water inlet valve blocked e Is the water pressure too low e Open the water tap Push the Start Pause button once e Clean the water inlet valve then push the Start Pause button once e Use after the water pressure is normal The display shows E6 e The water level sensor has failed e Please contact Customer Care Will not wash The machine e Is there a power failure e Is the power plug inserted tightly e Has the water level reached preset position e Wait for the power supply to be restored e Insert the power plug tightly e Wait for water to fill to the preset level Will not spin e Is the power plug inserted tightly e Is the to
15. s back on a non abrasive surface 2 Place the plate on to the bottom of the machine Front 3 Use a screwdriver to tighten the screws in accessory bag securing the panel to bottom of Back the washer 4 Once all screws are tight and the panel is secure return the washer to its standing Carpet Bottom plate position Balance washing machine Do not install this machine on an incline greater than 2 Installing machine on an angle or on rough ground will result in unstable running or stoppage of the machine Please adjust it by the following method 1 Confirm it is level 2 Lift up the side of the machine slightly and twist the adjustable leg Note The distance between the washing machine and wall should be at least 20mm A Win 20mm i w Operation amp Wash Cycles Press the button to start the cycle e f the top lid is opened while machine is in SPIN cycle the machine will stop and an audible alarm will sound Note The energy test program was performed using the Normal cycle default setting of Wash Long Rinse 1 Rinse Spin 7 mins HWMP60 118 9 mins HWMP70 118 HWMP70 118R Water level 10 Please use low suds high efficiency detergent Cycle completed When the machine has completed the selected current wash cycle an audible alarm will sound and the machine will switch off automatically 13 Operation amp Wash Cycles 3 Press the buttons to customise
16. the pre set options Separate colour fast clothes before loading washing machine During Rinse cycle only Spin times and Water level can be set all the other wash functions are locked For Wool program you can select procedure but can not change them For Tub Dry and Quick programs push the Wash Rinse and Spin button the machine has no reaction 4 Press the button to change the water level For the Synthetic and Memory cycles the machine will run a Fuzzy Logic program that automatically detects the type of laundry in the tub After detection it will set the water level automatically The water level can only be changed once the machine has started by pushing the Start Pause button then push the Water Level button to reset the water level Press the Start Pause button to resume the wash cycle D Press the 2 button to select the the wash and rinse temperature Set the wash and rinse temperatures in accordance to the requirements of each load The wash and rinse temperatures will be the same i e if Warm Cold is selected both wash and rinse cycles will be warm cold 6 Press the Geta button to select the delay wash program The delay time program is automatically off and wash cycles will start as soon as Start Pause button is pushed Confirm the operation of Delay program To set a delay time first select the Cycle and options required and push the Delay button
17. uild up Note If a manufacture specifies only the use of a low sudsing or high efficiency type detergent then detergent for drum type machines shall be used irrespective of the type of machine under test Otherwise the detergent type to be used shall be chosen according to the type of clothes washing machine under test as follows Avoid using whitener on laundry with colour or patterns as they are prone lose colour The bleach whitener should NOT be directly applied to laundry alarm will sound
18. verview ces coe Coe cee coe Coe Cee cee ooo cee oes Cee cee one Name Quantity Storage position Safety DIECAUIIONS lt 2 os Se eaens teaiseteeneet ees aai eee Automatic washing machine Installation and adjustment eco ooo coe coe ooo ee oo eco ooo 4 l Bottom plate Installation of drainage hose ece oco ooo ooo ooo ooo ooo ooo eD sane 5 SEEEN the poet union of tae Installation of water inlet hose 3 washing machine package and the l upper seal of the package carton Before washing cen Cae See Gee Mek BON Seb Won Bee bee wed cae aed Loading your aundiye rererere User manual e One Inside the document bag Detergent usage guide Serre Ce eT eT eT codo ses ess l Warranty card One Inside the document bag Operation amp wash cycles MaInNtAENaANncesrssssrcrrcerscscscccsccccccceccecccccescceccscscens TFOUDIS SHOOUING risers terete trsni epii aaa Tapping Screws e One Inside Accessory bag Packing liSteeeeeeeeeceecceccecccoccoccocoocoecoecocccccceccecee Components of the water inlet hose C t to th washing maching Inside Accessory bag Connect to the tap Drain hose Inside Accessory bag Drain hose Clamp Inside Accessory bag Drain hose hoop On The Drain hose 17 Common occurrences Situation e The spinning is intermittent after it starts Cause e Redistribute the load evenly Close the top lid e Select spin program but it does not work e The pro
Download Pdf Manuals
Related Search