Product Manual 1.0 MB - Rhin-O-Tuff
Contents
1. HD4170 SETUP amp OPERATOR MANUAL Performance Design Inc 2350 East Braniff St Boise Idaho 83 16 www Rhin O Tuff com Rhin O Roll Coiler Operator s Training Manual p p Issue 1 03 05 PDI Part 941000 Performance Design Inc 2350 East Braniff St Boise Idaho 83716 Issue 0 Part 941000 www RHIN O TUFF com This manual contains very important safety information and must be read HD 4170 Operator s Training Manual Issue 0 01 04 The HD 4170 Rhin O Roll Coiler will greatly increase productivity An in depth look at the set up procedures necessary to achieve maximum results follows The HD 4170 Rhin O Roll Coiler can attach to the HD 6500 HD 7000 or HD 7 00 Performance Design Inc punches and can also stand alone This manual discusses all of the necessary steps to use and care for your machine Issue 0 Part 941000 www RHIN O TUFF com Table of Contents Chapter Page Number 1 Important safety notice 4 2 Overview of your HD 4170 Rhin O Roll Coiler 5 Adjustable Roller Upper Roller Doc U Form Book Former Book Thickness Coil Selector and Roll Position Setting Power Switch Crimping Pliers Crimping Pliers Holder Roll Position Setting Adjustment Knob Fuse Holder 3 Detailed Use of the HD 4170 Rhin O Roll 7 gt Book Former gt Book Thickness Coil Selector and Roll Position Setting VVVVVVVVV V 4 Placing the HD 4170 in the proper location amp Bind2. CHAPTER EE Cleaning the HD 4170 Rhin O Tuff Coiler Caring for your HD 4170 Rhin O Roll is important for the proper function of the machine The finished tan and gray body should be cleaned with a very light water dampened cloth The upper and lower rollers should be cleaned with a rubber cleaner and rejuvenator dampened cloth while the machine has been turned off and cooled CHAPTER Product Registration Product registration is important to establish trouble free warranty repair of any of your Rhin O Tuff equipment Please fill out and mail in the card provided with your machine or register on line at www RHIN O TUFF com
3. and use of this feature Power Switch This switch turns the HD 4170 on and off Pushing on the symbol side of the switch turns the machine ON the O turns the machine OFF On 230VAC models this is on the rear of the machine It is recommended you turn the machine off when not in use In case of any emergency use the power cord as the main power Cutoff Crimping Pliers Used for cutting and crimping coil ends JN Crimping Pliers Holder A convenient place to store your pliers 8 Roll Position Setting Shows the current location of the Adjustable Lower Roller See Chapter 3 for further explanation and settings of this feature The Thumb Pull image shows the intended location of your thumb while pulling on the Adjustment Knob with your index and middle fingers to change settings of the Lower Roller Adjustment Knob Pull and move up or down to change the position of the Adjustable Lower Roller 6 Fuse Holder Not shown located on rear of machine Always replace fuses with the correct amperage and type PDI P N 007072 115vac or 001659 230vAC v 115VAC use tea FUSE 3 AMP AGC 1 X 1 14 v 230VAC use 2ea FUSE 1 5 AMP GMA M5 X 20MM Issue O Part 941000 www RHIN O TUFF com Illustration CHAPTER E Detailed Use of the HD 4170 Rhin O Roll gt Doc U Form Book Former See Illustration 3 0 The Doc U Form Book Former D shapes the binding end 2 of your book 3 so that insertion and S
4. i sie S25 MIN N Book posit Coil Size Indicator O D m N Nes and RO t Ta Hole Pitch Gage 000000000000000000000000 000000000000000000000000000006086 5 1 5MM 0000000000000000000000000868enn Illustration ni CHAPTER Placing the HD 4170 in the proper location amp Binding Styles Locate a clear work area with a outlet within 5 feet that provides a 15 amp service 16 amp European which is protected at the customer s circuit box The work area must be a solid firm cabinet or a heavy duty table with a flat level surface Power cord shall be certified for the country where the machine will be installed Placing your HD 4170 Rhin O Roll Coiler in the proper location will also depend on your binding technique If your binding technique is to punch and stack the entire job before coiling then positioning the HD 4170 away from your punch for more work area may be the best setup as well as leaving the HD 4170 on its stand alone feet as supplied However if your technique is to punch and coil a single book at one time and repeat until the job is complete then mounting the HD 4170 Coiler directly onto your HD 6500 HD 7000 or HD 7700 punch may be the best setup for you Please see Chapter 5 for instructions to mount your HD 4170 Coiler or skip to Chapter 6 for Binding CHAPTER Pa Mounting the HD 4170 onto the HD 6500 HD 7000 or HD 7700 See Illustration 5 0 Your HD 4170 Coiler came in the stand alone co
5. ighten the rear screw first then the forward screw Repeat this step on the other side of your punch with the other block CHAPTER Binding and Crimping See Illustration 6 0 Binding is as simple as with the HD 4170 Rhin O Roll Form Start Coil and Bind Doc U Form Book forming and lower Roll position is covered in Chapter 2 To bind firmly grab the book from the Start Coil position described in Chapter 3 with both hands at each end of the book up near the binding edge Without shifting the form of your book pick the book up and roll it into binding position between the top on lower roller Genily push the started coils against both top and lower roller The top roller will grab the coil and spin it into your book It may not be necessary to use the Book Former D with smaller 5MM 12MM books With practice 50MM specialty binding can be done TP D Illustration gt CD 10 See Illustration 6 1 Once you have coiled your book crimping is made easy with the crimping pliers provided Orient your book with the coiled side toward you D as shown then on the right end of the book D as shown orient the pliers with the dot facing up Open the pliers and grasp them around the first coil that exits the book While keeping the pliers level with the book snip the coil through The pliers will finish the coil with a L shaped end facing the book This helps the coil from backing out of the book Now you can fli
6. ing Styles 8 5 Mounting the HD 4170 onto the HD 6500 HD 7000 or HD 7700 9 6 Binding and Crimping 10 7 Trouble Shooting 12 8 Cleaning the HD 4170 Rhin o Roller Coiler 12 9 Product Registration 12 Issue O Part 941000 www RHIN O TUFF com CHAPTER 4 Important Safety Notice Make sure you read this section very carefully Learn to recognize this Safety Alert Symbol The HD 4170 Rhin O Roll Coiler has been designed to provide a very high level of protection to an operator Follow the guidelines below while installing operating and maintaining your machine Read this manual and keep and file this manual for future use D gt Always replace fuses with the correct amperage and type PDI P N 007072 115vac or 001659 230vAc JX v 115VAC use 1ea FUSE 3 AMP AGC 14 X 1 14 v 230VAC use 2ea FUSE 1 5 AMP GMA M5 X 20MM Refer to the serial number label on the rear of the machine to determine the voltage of your machine Performance Design Inc Boise ID www AHIN O TUFF com Model Type X1234 VOLTS AC AMPS Hz so Serial Number Label Example while the machine is on unplug the HD 4170 and call your dealer immediately for service A gt Ifthe machine runs erratically or if either wheel stops turning qualified Technician There are no user serviceable parts inside the HD 4170 Rhin O Roll Coiler NEVER REMOVE COVER doing so may result in personal injury A DANGER Hazardous voltage inside Discon
7. nect power before servicing AN gt Never attempt to service your machine unless you are a OXI HCE LLC MONEIN cresci cre IN Maceio Me HOMO power cord does not fit your outlet Power cord shall be certified for the country where the machine will be installed N gt Never operate the HD 4170 Rhin O Roll Coiler if the provided Issue 0 Part 941000 www RHIN O TUFF com Overview of the HD 4170 Rhin O Roll See Illustration 2 0 on next page The HD 4170 has many useful features to increase your coil binding productivity Adjustable Lower Roller The Adjustable Lower Roller supports the lower side of the coil while binding The Adjustable Lower Roller is also referred to as Roll in item 4 in Book Thickness Coil Selector and Roll Position Setting Upper Roller The soft Upper Roller grabs the coil and spins it into the book quickly and effectively Doc U Form Book Former allows you to form your book to allow for quick starting and binding of large books See Chapter 3 for further explanation and use of this feature Book Thickness Coil Selector and Roll Position Setting This multi use feature allows you to slide your uncoiled book into its thickness gauge and suggests the appropriate coil size to use for that job As well as giving you the suggested Lower Roll position setting it provides the answers to sizes and pitch of stray coils and punched sheets See Chapter 3 for further explanation
8. nfiguration In order to attach the HD 4170 Coiler you need to remove the feet Inside the HD 4170 shipping box is a knob kit with tools Locate the small Allen wrench and remove both feet from each side of the HD 4170 Coiler Do not remove the Interface Plate that mounts directly to the HD 4170 Coiler bottom side Store the feet screws and Allen wrench for future use Locate the Interface Blocks screws Allen wrenches and 3 winged knobs provided inside the shipping box These will be required in the next step Illustration HD 6500 and HD 7000 Instructions HD 7700 Instructions See Illustration 5 1 on next page See Illustration 5 2 on next page Locate the two top most and rear most Locate the two top most and forward screws on the side of your HD most screws on the side of your HD 6500 7000 Inserting the short end of 7700 Inserting the short end of the the Allen wrench into the screw head Allen wrench into the screw head remove the two screws remove the two screws Both HD 6500 7000 and HD 7700 Instructions cont Store the two screws removed from the punch Locate one of the Interface Blocks and orient it against the two now available holes Orient the block so that the interface block oval hole is forward and the counter bores face out To the right is an example of a counter bore Use the longer 4 20 socket head screws provided to secure the block to the machine with the short end of the Allen wrench T
9. p the book over keeping the coils toward you and repeat this same crimping technique to complete the book Or you can keep the book stationary and flip the pliers over move to the opposite end of the book and crimp the last coil that exits the book to complete the book TT Hill TO E T eg Illustration Your HD 4170 Rhin O Roll has an optional dual crimpier module that mounts on top of the coiler 11 CHAPTER 4 Trouble Shooting Only qualified personnel should attempt to work on this equipment Most of the problems you may encounter are due to setup problems There is one fuse on the 115VAC machine and two fuses on the 230VAC machine located on the rear of the HD 4170 Rhin O Roll Coiler that can be replaced by the customer Below is a trouble shooting guide to help you through most of the problems that may be encountered Trouble Shooting Upper and Lower Rollers 1 Machine is off Switch 1 Place switch in the do not rotate is in the O position position 2 Machine is not 2 Check both ends of plugged in the power cord 3 Blown fuse 3 Check fuse See Chapter 1 for fuse listing Coil tightens on the book 1 Coil is too small for the 1 Check proper size of book coil See Chapter 3 Coil stops before it is 1 The holes in the book 1 This is normal Try completely through the are misaligned moving the book around book so the coil rotates in the holes
10. tarting of the coil is simple to do Gently jog your book onto the Book Former until formed Then start the coil into the first 5 holes or more by spinning it in by hand Illustration gt Book Thickness Coil Selector and Roll Position Setting See illustration 3 1 on next page On top of the HD 4170 is the Book Thickness Coil Selector and Roll Position Setting feature It s simple to use You gently slide your book from left to right into the Book Thickness Coil Selector slot When you feel the book slightly wedge into the slot stop sliding the book and read both the recommended coil size selection number 16MM shown and the recommended Roll Position Setting number position 2 middle position shown These are only recommendations and you may find other combinations that suit your personal binding style Other features available are the Coil Size Indicator O D and the paper Hole Pitch Gage With the Coil Size Indicator Use the coil size indicator when the size of the coil is unknown Simply align the end outside diameter O D to the indicator and read your coil size Use the Hole Pitch Gage in the same manor to determine what pitch the paper has been punched with www RHIN O TUFF com CI 4170 Rhin O Roll 5MM A O MWRANIDIONWUIOGI BR ONO mam NON NON G gt 1 a gt 2 al c ot NU s gt z2S2z S0 bons s Coll SAC A gt gt N 2 A nicknes sa n Set
Download Pdf Manuals
Related Search