Superior Surge Suppressor Solutions
Contents
1. instruments to protect 4 20mA lines 28VDC Rail Mount Surge Suppressor Enclosed in a Moore Industries DIN style housing this surge suppressor protects 4 20mA lines Enclosure Mount Surge Suppressor A compact unit this 28VDC suppressor fits into Moore Industries field mount enclosures or mounts on top of DIN style instruments to protect 4 20mA line General Location Conduit Mount Surge Suppressor This 28VDC general location conduit mount surge suppressor mounts on the outside of field mount housings to protect 4 20mA line Explosion Proof Conduit Mount Surge Suppressor This 28VDC suppressor mounts on the outside of field mount housings to protect 4 20mA line with explosion proof certifications 28VDC Wire In Surge Suppressor Protect the power terminals of 4 wire line powered instruments with this surface mount surge suppressor 120VAC Rail Mount Surge Suppressor Enclosed in a Moore Industries DIN style housing this 120VAC surge suppressor protects the power terminals of 4 wire line powered instruments 220VAC Wire In Surge Suppressor Surface mount surge suppressor protects the power terminals of 4 wire line powered instruments 12VDC Rail Mount Surge Suppressor Enclosed in a Moore Industries DIN style housing this 12VDC surge suppressor protects data communication lines such as RS 422 and RS 485 What are some examples of units that this solution works with What is2. sub nanosecond speed can save your valuable equipment from electrical damage Resists Environmental Interference This surge suppressor s durable design coupled with RFI EMI filtering differential and common mode suppression and hermetically sealed components makes it ideal for use in hazardous environments Protect Almost Any Unit The DC Wire In Surge Suppressor works with any Moore Industries units that Installation require 28VDC power including the FCT HIT SPA SPT HFA MDS CCS and DDS Connecting For a typical installation of this product connect this unit to your DC power distribution after the power switch and fuse and as close to the electronic Figure 12 Dimensions of the DC Wire In Surge Suppressor equipment I protects as possible Connect the power lines as shown in Figure 13 Grounding The ground terminal must be connected to a good earth ground of AWG 14 or larger This unit contains no internal fuse and can fail short under direct lightning exposure therefore proper fusing is essential Heat sinking is not required Figure 13 Sample installation of the DC Wire In Surge Suppressor Specifications Performance Operating Voltage Performance Maximum Surge Voltage Performance ResponseTime 28 Volts Continued 20kV Continued 1nanosecond Maximum Operating Maximum Surge Current Voltage 30 Volts 8x20 usec 10kA Ambient Operating amp Storage Maximum Operating Current Leakage Line at Conditions
3. 5 863 06 estu mat INCOMING CURRENT 220VAC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 11 Specifications Performance Operating Line Voltage 50 60Hz 220VAC Maximum Operating Line Current 5 Amps Maximum Line Current 5 Amps Minimum Clamping Turn On 390V Maximum Clamping Voltage 9 500Amps Performance Continued 30 50 Grounding Both the protected unit s housing and the suppressor must be connected to a common good earth ground such as from the DIN Rail foot to the grounded rail the ground bolt on top of the suppressor or hard wired terminal blocks Keep the ground wire 12 AWG short and place the suppressor as close as possible to the equipment it is protecting Monitoring The front mounted LEDs will notify you if a surge has damaged the suppressor If L turns off you still have backup protection but should replace the unit If L turns off the unit is no longer functioning Figure 3 Dimensions of our AC Rail Mount Surge Suppressor AC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 11 Line Neutral 650V peak Performance Maximum Leakage Line Ground 650V peak Continued Current Each Line to Neutral Ground 650V peak Ground 220VAC Maximum Transient Voltage 60Hz 1 0mA 1 2x50 microseconds 20kV Response Time Maximum Transient Current 1 nanosecond 8x20 microseconds 10kA Frequency Attenuation Ambient Operating amp Storage dB G 100kHz 10MHz Conditions Temperature 40 C t
4. 85 C 40 F to 185 F Page 11 Superior Surge Suppressor Solutions The Interface Solution Experts www miinet com Mi United States info miinet com Belgium info mooreind be China sales mooreind com cn MOORE Tel 818 894 7111 FAX 818 891 2816 Tel 03 448 10 18 FAX 03 440 17 97 Tel 86 21 68406724 FAX 86 21 50623585 IND USTRI ES Australia sales mooreind com au The Netherlands sales mooreind demon nl United Kingdom sales mooreind com Tel 02 8536 7200 FAX 02 9525 7296 Tel 0 344 617971 FAX 0 344 615920 Tel 01293 514488 FAX 01293 536852 700 710 100 A Rosemount is a registered trademark of Rosemount Inc iil moore INDUSTRIES AC Rail Mount Surge Suppressor Part Number 205 863 11 User s Manual January 2005 AC Rail Mount Surge Suppressor Part Number 205 863 11 Universal Protection The Rail Mount Surge Suppressor works with any Moore Industries unit that requires 220VAC power This includes the SPA SPT FCT ECA PIT PVT PWT PWV PAC and PAV Multistage Protection This suppressor protects your process with two levels of protection Two front mounted LEDs L for primary protection L for secondary illuminate when the suppressor is functioning properly When L turns off the suppressor still has backup protection working but should be replaced When L turns off the suppressor is no longer functioning Tough P
5. Loop Line Part Number 205 863 06 12VDC Data Line Part Number 205 863 07 The Rail Mount Surge Suppressor is designed to mount on any Top Hat or G type DIN rail This versatile unit is available in models that will protect both analog or digital signals Protect Almost Any Unit The Rail Mount Surge Suppressor is available in a 12 and 28VDC version and works with most Moore Industries units The 28VDC version is designed to provide superior protection to 4 20mA loop lines Its narrow housing combined with the ability to mount directly on a DIN style rail makes it perfect for spaces that won t allow you to fit a DIN plug or Enclosure mount suppressor Protect Communication Lines The 12VDC version provides you with incredible protection specifically designed for communications lines This unit will work with RS 422 and RS 485 communication lines Put one of these units on both ends of your long runs of communications wire to ensure that your transmitter and receiver are both protected from overvoltage damage Tough Protection Exceeding severity Level 4 of IEC 1000 4 4 recommendations this unit s sub nanosecond response time stops failures due to lightning spikes and overvoltage surges while minimizing other electrical noise Installation For installation instructions follow the directions for the AC Rail Mount Surge Suppressor on page 8 Specifications Performance RS Applications 12 Volt Unit RS 422 RS 485 28 Volt Un
6. Lu MOORE Superior Surge INDUSTRIES Suppressor Solutions February 2000 Data Sheet 13 00 Description Features Moore Industries family of reliable surge suppressors e Protect from failure due to overvoltage stress protects your process against failures caused by Our suppressors protect against power fluctuations lightning power spikes and many other types of such as switching inductive loads switch contacts overvoltage damage Overvoltage damage takes many arcing motors cycling fuses clearing circuit forms from gradually reducing measurement accuracy breakers tripping or power outages that can and product quality to destroying a unit outright and gradually wear down the life of electronic circuits Causing an unneccessary and costly shutdown e Hassle Free Protection Easy installation combined Providing up to 3kA of surge protection per line at with a safety feature that automatically resets the subnanosecond speeds our suppressors protect your suppressor after each surge makes these surge process with the most effective suppression available suppressors hassle free and maintenance free Combine this lightning fast protection with a multistage design and a safety feature that resets automatically e Versatile Housings These accessories to our after each surge and you have a hassle free surge popular line of interface instruments are available in suppressor that provides affordable powerful nine versatile housing configurations t
7. Temperature Current 5 0 Amps Operating Voltage 0 5mA 40 C to 85 C Maximum Clamping 40 F to 185 F 500A 46 Volts Page 10 The Interface Solution Experts Specifications subject to change Printed in U S A AC Wire In Surge Suppressor Part Number 205 863 03 The AC Wire In Surge Suppressor provides powerful protection for the 220VAC power lines of your process Meeting severity level 4 of IEC 1000 4 4 and 1000 4 5 this surge suppressor s incredible protection and sub nanosecond speed can save your process from electrical damage Resists Environmental Interference This surge suppressor s durable design coupled with RFI EMI filtering differential and common mode suppression and hermetically sealed components makes it ideal for use in severe environments Protect Almost Any Unit The AC Wire In Surge Suppressor works with any Moore Industries unit that requires 220VAC power including the SPA SPT FCT ECA PIT PVT PWT PWV PAC and PAV Figure 14 Dimensions of the AC Wire In Surge Suppressor S NSI SESS Specifications Performance Performance Continued Operating Line Voltage 50 60Hz 220 240VAC Maximum Operating Line Current 5 Amps Maximum Line Current 6 Amps Maximum Transient Voltage 6kV Maximum Transient Current 4kA Clamping Action Turn On 390 Volts Specifications subject to change Superior Surge Suppres
8. a GROUND Bu WIRE P T 24mm a lt 0 86 in Installation Connecting amp Grounding For a typical installation of this product plug the surge suppressor unit into the input or output loop terminal block of the Moore Industries DIN unit as shown in Figure 6 Plug the terminal block header into the back of the surge suppressor The suppressor must be connected to a good earth ground Equipment and suppressor ground should be common Maintenance is not required but MOORE INDUSTRIES DIN UNIT DIN PLUG SURGE SUPPRESSOR we recommend that instrument zero be checked after Specifications installation Performance Operating Voltage Performance Maximum Clamping 2kA Performance Capacitance Line at Rated 28 Volts Continued 8x20 usec 46 Volts Continued Voltage 500pF Maximum Operating Maximum Surge Voltage Response Time Voltage 30 Volts 20kV lt 1 nanosecond Maximum Operating Maximum Surge Current Current 200mA 8x20 usec 2 5kA line Ambient Operating amp Storage Clamping Action Turn On Current Leakage Line at Conditions Temperature 31 4 Volts Operating Voltage 5 uA 40 C to 85 C 40 F to 4 185 F Page 6 The Interface Solution Experts Specifications subject to change Printed in U S A Superior Surge Suppressor Solutions Conduit Enclosed Suppressors Explosion Proof P N 205 863 09 General Location P N 205 863 08 Practical Protection The Conduit Enclo
9. c Ia 0 44 EE O u UENEN ng T ay fes gt o N gt TA e LU m E a Y OO uo o Og rn o Y Oo X LLI D LSS ys Sf amp Nes AR P N 205 863 07 12VDC RAIL MOUNT SURGE SUPPRESSOR V B sla es 1 15 1 uK LINK Mr 1 CH 1 CLOSED oo oo olo olo olo olo olo olo ol oo olo ob rageg o el INDUSTRIES IMM Tl moore Page3 The Interface Solution Experts Specifications subject to change Superior Surge Suppressor Solutions Enclosure Mount Surge Suppressor Part Number 205 863 02 Providing complete loop protection in a compact frame our Enclosure Mount Surge Suppressors can be mounted to almost any instrument Versatile Protection This advanced suppressor can be velcro mounted to the top of any DIN unit or for a more rugged application placed inside of a Moore Industries BH or D BOX enclosure Because of its ability to allow HART signals to pass through you can use this surge suppressor to protect both analog and HART digital analog signal lines Suppress Harsh Surges Exceeding severity level 4 of IEC 1000 4 4 this suppressor provides 2 5kA line of surge protection Lightning fast response time stops failures due to lightning spikes and overvoltage The Enclosure Mount Surge Suppressor can be mounted easily surges while minimizing other electrical noise either i
10. g P N 205 863 08 Certification pending consult factory for details Page 2 The Interface Solution Experts Specifications subject to change Printed in U S A Superior Surge Suppressor Solutions Figure 2 Sample Loop Installations tc un 52S LW a 26o TQ 0 yy o LO 5 cc On a O U Fs AgS rhe eo gt 0 GA ZA sy F Ons zuo oO s W D ep uy C G i0 5 2202 DANA me Owe Og P Lu qp LLI PLS OS 2 g 0 NY ee o U i5 t5 DC Og EE zog e PE 29 ONS z Ho JA eiu x 5 50 Ts E i Soo Q 0 x LETT GREEN GROUND sf Cd for fee LEN ENCLOSURE MOUNT SURGE SUPPRESSOR P N 205 863 02 PAGE 4 2 oztmo amp zu gt 0 HE E c LLJ ILI 1 MH ooo Q M zg B o 398 D EON 5 DOO yy O atog e zc e z os OOS og z a eo CN P N 205 863 06 28VDC RAIL MOUNT SURGE SUPPRESSORS De 655 4 20mA CABLE AS CAN J I ATA a SN Waa oS SAAN NS RAEAN Wien L11 111 i I LLLI raa T LLL LL L4 LL Lippe pee EA ECEE LZ CONTROL ROOM r tc Zo BAS W w gt
11. hat can protect protection every portion of your process from damage Figure 1 For complete loop protection it is necessary to place surge suppressors at both ends of the loop FIELD SSS SSS 3S 33S SSS SSeS LL SS SS CONTROL 28VDC CONDUIT MOUNT Jj 28VDC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 06 _ ROOM SURGE SUPPRESSOR P N 205 863 08 PAGE 7 PROTECTED LITT ons IAM p i The Interface Solution Experts 2000 Moore Industries International Inc Specifications subject to change Printed in U S A Superior Surge Suppressor Solutions Ordering Information What type of line What type of do you need to unit does protect this line connect to DIN Style Rail mount instruments 4 20mA Loop Field Mount Enclosure 28VDC Power Lines 4 Wire Instrument Power Lines 120VAC Power Lines 220VAC Power Lines RS 422 RS 485 Communication Lines 12VDC Power Lines Certifications What type of solution do you need DIN Plug Surge Suppressor This plug in terminal block surge suppressor inserts into Moore Industries DIN style housing terminals to protect 4 20mA lines Enclosure Mount Surge Suppressor A compact unit this 28VDC suppressor fits into Moore Industries field mount enclosures or mounts on top of DIN style
12. it none Performance Clamping Action Turn On Continued 12 Volt Unit 14 3 Volts 28 Volt Unit 31 4 Volts The DC Rail Mount Surge Suppressor Family are multipurpose units that can protect analog digital analog or communication lines Figure 11 Dimensions of our AC and DC Rail Mount Surge Suppressors DC RAIL MOUNT SURGE SUPPRESSORS P N 205 863 06 amp 205 863 07 AC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 05 Performance Current Leakage Line at Continued Operating Voltage 5 uA Capacitance Line at Rated Operating Voltage 12 Volt Unit 12 Volts 28 Volt Unit 28 Volts Maximum Operating Voltage 12 Volt Unit 14 Volts 28 Volt Unit 30 Volts Maximum Operating Current 200mA Specifications subject to change Maximum Clamping 2kA 8x20 usec 12 Volt Unit 22 Volts 28 Volt Unit 46 Volts Maximum Surge Voltage 20kV Ambient Maximum Surge Current Conditions 8x20 usec 3kA line The Interface Solution Experts Voltage 12 Volt Unit 2000pF 28 Volt Unit 500pF Response Time lt 1 nanosecond Operating amp Storage Temperature 40 C to 85 C 40 F to 185 F Page 9 Superior Surge Suppressor Solutions DC Wire In Surge Suppressor Part Number 205 863 04 The DC Wire In Surge Suppressor provides powerful protection for the 28VDC power lines of your process Meeting severity level 4 of IEC 1000 4 4 and 1000 4 5 this surge suppressor s incredible protection and
13. ly mounted on any standard DIN rail Connecting Connect each incoming power line to the appropriate plug of the FIELD terminal block as shown in Figure 10 Connect wires from the protected instrument to the appropriate plug of the EQUIPMENT terminal block of the surge suppressor Grounding Both the protected unit s housing and the suppressor must be connected to a common good earth ground such as from the DIN Rail foot to the grounded rail the ground bolt on top of the suppressor or hard wired terminal blocks Keep the ground wire 12 AWG short and place the suppressor as close as possible to the equipment it is protecting Monitoring The front mounted LEDs on the AC unit will notify you if a surge has damaged the suppressor If L turns off the unit is working but should be replaced If L turns off the unit is not functioning Performance Continued Maximum Leakage Current Each Line to Ground 120VAC 60Hz 0 5mA ResponseTime 6 Amps Maximum Transient 1 nanosecond Clamping Action Turn On Current 1 2x50 usec 10kA 210 Volts Frequency Attenuation dB Ambient Operating amp Storage Maximum Clamping 100kHz 10Mhz 30 50 Conditions Temperature Voltage 500Amps 40 C to 85 C Page8 40 F to 185 F The Interface Solution Experts Specifications subject to change Printed in U S A Superior Surge Suppressor Solutions Loop amp Data Line Rail Mount Surge Suppressors 28VDC
14. nside one of our rugged field mount enclosures or on top of a Moore Industries DIN style instrument housing Perfect for Rugged Environments This durable Suppressor is hermetically sealed and suitable for the most harsh industrial environments Figure 3 The compact enclosure mount surge suppressor fits into most enclosures and housings TO EQUIPMENT The Enclosure Mount Surge Suppressor works with most Moore Industries units including the following T ture T itt THZ TRX TRY TDZ emperature Transmitters TDY RIY TIY And More DDS MDS DDA IPT Select the suppressor that is appropriate for your application Isolators Converters SCX ACX SIY amp Transmitters SIX ECT ECD Specifications Performance Operating Voltage Performance Maximum Clamping 2kA Performance Capacitance Line at Rated 28 Volts Continued 8x20 usec 46 Volts Continued Voltage 500pF Maximum Operating Maximum Surge Voltage Response Time Voltage 30 Volts 20kV lt 1 nanosecond Maximum Operating Maximum Surge Current Current 200mA 8x20 usec 2 5kA line Ambient Operating amp Storage Clamping Action Turn On Current Leakage Line at Conditions Temperature 31 4 Volts Operating Voltage 5 uA 40 C to 85 C 40 F to 185 F Page4 The Interface Solution Experts Specifications subject to change Printed in U S A Superior Surge Suppressor Solutions Installation Field Mount Enclosure Connection amp G
15. o 85 C 40 F to 185 F The Interface Solution Experts www miinet com G 7 United States infoG miinet com MOORE Tel 818 894 7111 FAX 818 891 2816 INDUSTRIES vei 02 8536 7200 Fax 02 9525 7206 Belgium info mooreind be Tel 03 448 10 18 FAX 03 440 17 97 The Netherlands sales 9 mooreind nl Tel 0 344 617971 FAX 0 344 615920 China sales 9 mooreind sh cn Tel 86 21 62481120 FAX 86 21 62490635 United Kingdom sales mooreind com Tel 01293 514488 FAX 01293 536852 Rosemount is a registered trademark of Rosemount Inc
16. pplied velcro Figure 5 The Enclosure Mount Surge Suppressor provides remarkable surge protection for loops that use BH and D BOX mounted devices BH HOUSING Specifications subject to change The Interface Solution Experts LI D BOX HOUSING Page 5 Superior Surge Suppressor Solutions DIN Plug Surge Suppressor Part Number 205 863 01 Suppress Harsh Surges Exceeding severity level 4 of IEC 1000 4 4 and 1000 4 5 this unit provides 2 5kA line of surge protection Lightning fast response time stops failures due to lightning spikes and overvoltage surges while minimizing other electrical noise Compact Power The DIN Plug Surge Suppressor is designed to fit onto any Moore Industries 2 prong terminal block header Economical small and powerful this unit has the suppression technology you need for use in the field with a compact design that will fit in the most cramped of control rooms It is available in a 28 volt model that protects most Moore Industries instruments including the following from overvoltage current running along 4 20mA lines The DIN Plug Surge Suppressor is a perfect fit for any DIN unit with THZ TRX TRY our 2 terminal header Temperature Transmitters RIY TIY THZ Figure 7 Dimensions of the DIN Plug Surge Suppressor Isolators Converters SIY ECT DIN SPT amp Transmitters and More PR E 29mm DS Figure 6 Sample Installation of the DIN Plug Surge Suppressor 1 15 in
17. ppressor Solutions AC Rail Mount Surge Suppressor Part Number 205 863 05 Universal Protection The Rail Mount Surge Suppressor works with any Moore Industries unit that requires 120VAC power This includes the SPA SPT FCT ECA PIT PVT PWT PWV PAC and PAV Multistage Protection This suppressor protects your process with two levels of protection Two front mounted LEDs L for primary protection L for secondary illuminate when the suppressor is active Tough Protection Exceeding severity Category B of ANSI IEEE C62 41 1991 recommendations this unit s sub nanosecond response time stops failures due to lightning spikes and overvoltage surges while minimizing other electrical noise Figure 10 Typical installation process for our AC and DC Rail Mount Surge Suppressors 28VDC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 06 k Mg Y M ES mA INCOMING CURRENT 120VAC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 05 Specifications Performance Operating Line Voltage 50 60Hz 125VAC Maximum Operating Line Current 5 Amps Maximum Line Current Continued Performance Line Neutral 295V peak Line Ground 345V peak Neutral Ground 330V peak Maximum Transient Voltage 8x20 psec 20kV The AC Rail Mount Surge Suppressor is designed for use with Moore Industries 120VAC transmitters alarms and other units Installation Mounting The Rail Mount Surge Suppressor can be quickly and easi
18. rotection Exceeding severity Category B of ANSI IEEE C62 41 1991 recommendations this unit s sub nanosecond response time stops failures due to lightning spikes and overvoltage surges while minimizing other electrical noise The AC Rail Mount Surge Suppressor is designed for use with Moore Industries 220VAC transmitters alarms and other units Figure 1 For complete loop protection it is necessary to place surge suppressors at both ends of the loop I I I 28VDC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 06 I I I I I SN e YX S er ER ZN 220VAC INCOMING PROTECTED ie 4 20mA CABLE 220VAC RAIL MOUNT SURGE SUPPRESSOR P N 205 863 11 D NEUTRAL The Interface Solution Experts 2005 Moore Industries International Inc 700 701 86A Specifications andinformation subjectto change without notice AC Rail Mount Surge Suppressor Installation Mounting The Rail Mount Surge Suppressor can be quickly and easily mounted on any standard DIN rail Connecting Connect each incoming power line to the appropriate plug of the FIELD terminal block as shown in Figure 2 Connect wires from the protected instrument to the appropriate plug of the EQUIPMENT terminal block of the surge suppressor Figure 2 Typical installation process for our AC and DC Rail Mount Surge Suppressors 28VDC RAIL MOUNT SURGE SUPPRESSOR P N 20
19. rounding For a typical field mount enclosure installation of this product establish the electrical connections before mounting the surge suppressor Connect the wires from the field to the terminal block headers on the front of the surge suppressor Connect the red and black wires from the side of the surge suppressor to the appropriate terminal of your unit Finish the connections by connecting the green ground wire on the surge suppressor to a good earth ground such as a ground screw attached to the base of the enclosure Equipment ground and suppressor ground should be common Mounting Mount the surge suppressor to the side or bottom of your enclosure using the supplied velcro as shown in Figure 5 Though maintenance is not required we recommend that the instrument zero be checked after installation DIN Style Housing Connection amp Grounding Connect the wires as shown in Figure 4 with the wires from the field connecting to the terminal block on the front of the surge suppressor and the wires from the Figure 4 The compact Enclosure Mount Surge Suppressor mounts onto or inside of most enclosures and housings NCLOSURE MOUNT URGE SUPPRESSOR P N 205 863 02 oim INDUSTRIES DIN STYLE TRANSMITTER side of the surge suppressor going to ground and to the terminal block of the protected unit Mounting To finish the installation on a DIN unit mount the surge suppressor to the top of the DIN unit using the su
20. sed Surge Suppressor can be attached to any 1 2 NPT pipe to provide quality surge suppression and either explosion proof or general location certification This advanced surge protection and space saving design makes these suppressors ideal solutions for protecting your field mounted instruments like the LH enclosure that don t have room for an Enclosure Mount Surge Suppressor HART Pass Through Both of the Conduit Enclosed Surge Suppressors pass HART signals making them effective choices for both digital and analog lines Figure 8 Dimensions of the Conduit Enclosed Surge Suppressors EXPLOSION PROOF CONDUIT ENCLOSED SURGE SUPPRESSOR P N 205 863 09 135mm 4 30 in 104mm 4 10 in O Z GEDNEY TYPE OE OUTLET BOX i FOR HAZARDOUS LOCATIONS CLI GR C D CLII GR E E G CLIII CAUTION KEEP COVER TIGHTLY 29mm 42mm 1 15 in 1 64 in ATTENTION GARDER LE COUVERCLE BIEN FERME LORSOUE LES CIRCUITS SONT SOUS TENSION CLOSED WHEN IN OPERATION i 205 863 08 49mm 205 863 09 1 93 in 39mm 1 52 in GENERAL LOCATION CONDUIT ENCLOSED SURGE SUPPRESSOR PIN 205 863 08 124mm 4 87 in 99mm Specifications Performance Operating Voltage 28 Volts Maximum Operating Voltage 30 Volts Maximum Operating Current 200mA Clamping Action Turn On 31 4 Volts 20kV The Interface Solution Experts Specifications subject to change Performance Maximum Clamping 2kA Continued 8x20 usec 46 Volts Maximum S
21. sor Solutions Installation Connecting For a typical installation of this product connect this unit to your instrument after the power switch and fuse and as close to the electronic equipment it protects as possible Connect the input power lines to the appropriate place on the FIELD side of the surge suppressor as shown in Figure 15 Connect the power lines going to the protected unit to the appropriate connections on the EQUIPMENT side of the surge suppressor Grounding The ground terminal must be connected to a good earth ground AWG 14 or larger Protected equipment ground and suppressor ground should be common Dress output clean lines away from incoming lines This suppressor contains no internal fuse and can fail short under direct lightning exposure therefore proper fusing is essential Heat sinking is not required Figure 15 Sample installation of the AC Wire In Surge Suppressor Maximum Clamping Voltage Line Neutral 410 Volts Line Ground 430 Volts Neutral Ground 430 Volts Suppressed Voltage Rating V UL 1449 2 Edition TVSS Line Neutral 600V peak Line Ground 700V peak Neutral Ground 600V peak Frequency Attenuation 100kHz 30dB 10MHz 60dB The Interface Solution Experts Performance Continued Ambient Conditions Maximum Leakage Current Each Line to Ground 220VAC 60Hz 0 5mA ResponseTime 1 nanosecond Operating amp Storage Temperature 40 C to
22. the Where is more information on this solution Part Number for your solution ECT DIN RIY SIY SPT THZ TIY TRY 20986201 Page 6 SCX ACX DDA DDS ECT ECD FCT IPT MDS PIT SIX 205 863 02 Page 4 Any unit with a 4 20mA input output AUTROS Page 9 ACX DDA DDS ECT ECD MDS PSD SCX SIX TDY TDZ 205 863 02 Page 4 Any unit with a 1 2 NPT conduit pipe and a 4 20mA input or output 205 863 08 Page 7 Any unit with a 1 2 NPT conduit pipe and a 4 20mA input or output 205 863 09 Page 7 Any unit that is poweredby 28VDC 205 863 06 Page 9 Any unit that is powered by 120VAC areas Page 8 Any unit that is powered by 220VAC 205 863 03 Page 11 CCS DDS MDS 205 863 07 Page 9 UL Listed Component Explosion Proof Class I Groups C amp D Class II Groups E F amp G Class III Conduit Enclosed Surge Suppressor Housing P N 205 863 09 UL Recognized Component USA Canada General Ordinary Location AC Wire In Surge Suppressor P N 205 863 03 AC Rail Mount Surge Suppressor P N 205 863 05 UL Listed Component General Ordinary Location DIN Plug Surge Suppressor P N 205 863 01 Enclosure Mount Surge Suppressor P N 205 863 02 Underwriter s Laboratories Data Line Rail Mount Surge Suppressors P N 205 863 06 amp 205 863 07 Conduit Enclosed Surge Suppressors P N 205 863 08 amp 205 863 09 Conduit Enclosed Surge Suppressor Housin
23. urge Voltage 8x20 usec 2 5kA line Current Leakage Line at Operating Voltage 5 uA Installation Connecting The conduit style surge suppressor allows you to connect any 2 NPT pipe directly to the surge suppressor Open the case and connect the wires from the 4 20mA loop to the FIELD side of the unit Connect the positive and negative wires on the EQUIP side of the unit to the instrument s terminals Mounting Mount the suppressor as close as possible to the equipment it is protecting If attaching to an explosion proof housing make sure to follow the proper standards Grounding A separate earth ground is not required if the instrument conduit is properly grounded Use 12 AWG or larger if a ground wire is needed Figure 9 Installation of the Conduit Enclosed Surge Suppressors TO 4 20mA LOOP FROM INSTRUMENT EXPLOSION PROOF CONDUIT ENCLOSED SUPPRESSOR P N 205 863 09 SURGE SUPPRESSOR SOLUTIONS e LOOP PROTECTION El 28VDC 4 20mA L IMOOR 8 INDUSTRIES P N 205 863 08 SURGE SUPPRESSOR SOLUTIONS a e LOOP PROTECTION amp GENERAL LOCATION CONDUIT ENCLOSED SUPPRESSOR P N 205 863 08 amp LLIIMOORE 29voc 20m amp INDUSTRIES P N 205 263 08 ae Performance Capacitance Line at Rated Continued Voltage 500pF ResponseTime 1 nanosecond Maximum Surge Current Ambient Operating amp Storage Conditions Temperature 40 C to 85 C 40 F to 185 F Page 7 Superior Surge Su
Download Pdf Manuals
Related Search