SDL-400E Manual - Protex Safe Co.
Contents
1. AGE SUSTAINED THROUGH BURGLARY THEFT ROBBERY FIRE OR OTHER HAZARD THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESSED OR IMPLIED BY LAW AND OR CUSTOM In the event of a defect in materials or workmanship covered by this warranty the purchaser shall return at purchaser s expense the product to Protex Safe Co for repair or replacement Repair or replacement shall be at the election of Protex Safe Co The purchaser s sole remedy shall be the repair or replacement of the product and under no circumstances shall Protex Safe Co be liable to the purchaser or any other person for any consequential incidental economic direct indirect general or special damages arising out of any breach of warranty In no event shall Protex Safe Co s liability exceed the original cost of the product This warranty and remedies set forth above are exclusive and in lieu of all others oral or written expressed or implied No dealer distributor agent or employee is authorized to make any modification or addition to this warranty PROTEX SAFE CO EXPRESSLY DISCLAIMS ANY WARRANTY OF NONINFRINGEMENT PROVIDED UNDER KRS 355 2 312 UCC 2 312 OR SIMILAR LAW PROTEX SAFE CO SHALL NOT INDEMNIFY NOR BE RESPONSIBLE FOR ANY DAMAGES ARISING OUT OF A CLAIM THAT THIS PRODUCT INFRINGES ANY PATENT Some states do not allow the exclusion or limitation of implied warranties or limitation of liability for incidental or consequential damages so t2. Using the power override box Changing the Master Code o M o M If your keypad does not respond don t be alarmed Most likely e This safe box also has a secondary code called Master Code the batteries are dead and need replacing This code can be used as an additional code to the user code you You will be able to open the safe using the power override box previously programmed as follow e The factory default master code is 8 8 8 8 8 8 8 8 this code will 1 Take a 4 AA batteries and install them into the also open the safe You can leave this code as is or you can change it black external battery box included with your safe We recommend changing this code for added security 2 Locate the outlet on the top right edge of keypad To change the master code please follow these steps and insert the jack 1 Press and hold the key for 5 seconds until the orange 3 While the battery box is plugged in go a head LED Aaa indicator blinks and enter your code as you normally would and open the safe so 2 Enter the existing master code Factory 8 8 8 8 8 8 8 8 and 4 Now you can replace the batteries inside the safe press The green LED open will stay lit 3 Enter a new 6 10 digit master code and press to end The green LED indicator will light up and you will hear 2 fast beeps confirming the new master code is accepted The battery override feature is used to give power to the lock from the outside of the safe wh
3. e piece of paper it s written on NEVER LOCK YOUR CODE INSIDE THE SAFE e Your code must consist of 4 to 10 digits e Always press the key after the last digit to open e Check your new code at least 3 times with the door open before you close the safe Changing your code Repeat steps 1 5 on this page except enter your existing code the code you are using to open the safe instead of the factory code 0 in step 3 Serial Number Model Number Date of Purchase Notes Notes PROTEX SAFE CO LIMITED WARRANTY Ee A Bice oR et a ae pa a a ag No oe 6 ria j La L i mil a S lec Ta E 1 iE iil i bs Zi Fy EI gi HE ESN Protex Safe Co Protex Safe Co warrants to the original purchaser that the product s shall be free of defects in material and workmanship for a period of one 1 year from the date of manufacture by Protex Safe Co complete safes This warranty applies provided there is compliance with all installation operating instructions supplied by Protex Safe Co and provided further that the product has been subject to normal use without any misuse negligence modification or the occurrence of accidental damage PROTEX SAFE CO MAKES NO OTHER WARRANTY WITH RESPECT TO THE PRODUCT EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY AS TO SUITABILITY OF THE PRODUCT FOR ANY PARTICULAR PURPOSE OR USE OR THE MERCHANTABILITY THEREOF AND SHALL NOT BE LIABLE FOR ANY LOSS OR DAM
4. en the internal batteries are dead 4 Now try to open the safe by entering the new master code follow by IMPO RTAN T Battery override box TIPS Make sure to remember the master code as this is your alternative way to open the safe if the user code is lost or forgotten e The override box is only to be used in an emergency when the internal batteries die or very low If you open the safe by using the master code the user code will e Unplug the override wire after replacing the internal return to the factory setting of 1 1 1 1 batteries NEVER LOCK THE OVERRIDE BATTERY BOX INSIDE THE SAFE 5 6 Troubleshooting Low battery warning O O The lock is equipped with a low battery warning indicator If the red low volt LED indicator lights up it is time to change batteries PROBLEM REASON SOLUTION We recommend always using Duracell or Energizer brand of Alkaline r batteries 4AA batteries are needed to operate the lock Green light is on but Batteries are Replace batteries safe will not low open Low Batte Indicator Orange light is on Wrong code was Enter the correct and lock is entered code again beeping Keypad is not Batteries are dead Open safe using responding and need the override battery dead replacement box and replace internal batteries Note The safe keeps the code in memory up to 6 months without power You will not need to reprogram your code after changing batterie
5. fe Company 8445 Canoga Avenue Canoga Park CA 91304 USA TEL 818 773 8030 FAX 818 773 8003 www protexsafe com PROTEX SAFECO User Manual SDL400E PROGRAMMING ELECTRONIC DROP BOX AND OPERATION V10 4 12
6. he above limitation or exclusion may not apply to you NOTICE Installation of the product with any unapproved accessorial item or product may invalidate the Protex Safe Co Limited Product Warranty Opening the safe ee Opening your drop box for the first time l 2 Press 1 1 1 1 This is the factory default code the green LED light open will light up confirmed by a beep sound You now have 3 seconds to turn the knob clockwise and open the door If you do not open the door within those 3 seconds the safe will relock itself and you will need to enter the code again If the orange LED alarm flashes with 3 rapid beeps it means that you entered the wrong code Please try again If you enter the wrong code for 3 consecutive times the lock will go into a LOCKOUT mode and you won t be able to open the safe for 5 minutes During this period there will be no response from the keypad If this happens please wait and try again after 5 minutes The LOCKOUT mode is a security feature to prevent someone from trying to manipulate the lock by entering guessed codes GREEN OPEN LED EXTERNAL POWER SUPPLY OUTLET RED LOW BATTERY LED ORANGE ALARM LED KNOB Content o M Opening the safe as Enrolling Changing a code Low battery warning Replacing batteries as Using the power override box Changing the master code ss Troubleshooting aaa aka SAFECO Protex Sa
7. s Changing Batteries Remove screw to open battery cover Orange LED is on The wrong code Must wait 12 and keypad will not was entered 3 minutes for the lock respond lockout consecutive times to reset from a lockout mode To replace the batteries locate the battery box in the back of the door Unscrew the phillips head screw and remove the cover Remove the 4 batteries and replace with new high quality Alkaline AA batteries Replace the cover and check your code to make sure that the safe is working properly NEVER USE OLD OR LEAKING BATTERIES Battery Cover Enrolling Changing a code O Enrolling a new code for the first time 1 Open the door and turn the knob so the bolts are out Locked position 2 Press the pound key 2 times This will enter the lock into a code change mode and orange LED will light up 3 Now enter the factory default code 1111 and press the key 4 Enter your new 4 10 digit code and press the key The green open LED will light up you will hear two beeps confirming the acceptance of the new code 5 Check your new code by entering your code and then 6 Refer to page 6 to change the secondary MASTER code IMPO RTAN T Do not pause for more then 7 seconds when you do steps 2 4 We recommend that you right your new 4 10 digit code on a piece of paper to avoid any errors when programming Always make sure to remember your new code and destroy th
Download Pdf Manuals
Related Search