Important Safety Instructions and Maintenance
Contents
1. Important Safety Instructions and Maintenance Important Safety Instructions N CAUTION Risk of electronic shock do not open Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards m x i Refer all servicing to qualified service personnel not open M To reduce the risk of fire or electric shock do not expose this product to rain or moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus In case of smoke strange noise or strange smell from the unit Turn off the power switch immediately Disconnect the power plug from the power outlet Contact your dealer or service centre Never attempt to make repairs yourself because this could be dangerous Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short circuit parts that could result in a fire or electric shock Never spill liquid of any kind on the set Use special caution in households where children are present The apparatus is not suitable for children under 3 year to operate Power supply cords should be routed safety to prevent life and property from dangerous with damaged cord Mains plug is used as the disconnect device It shall remain readily operable and should not be obstructed during intended2. 4 gt ADJUST SELECT Basic operation to be continued The way to adjust Brightness contrast backlight color temperature and scale mode please refer to Adjusting the Picture on Page16 17 2 Window This TV supports no higher than 60Hz under VGA mode so please set the re fresh rate of PC to 60Hz If the frequency is higher than 60Hz the screen may flicker When the TV is in VGA mode press MENU button on the remote control Press lt gt Arrow button to select Window d E n T E i PICTURE AUDIO SETTING FUNCTION PICTURE AUDIO SETTING FUNCTION H POSITION V POSITION H POSITION V POSITION CLOCK PHASE AUTO ADJUST 4 gt ADJUST SELECT 4 gt ADJUST SELECT MENU EXIT 1 Adjusting picture H Position Press V A Arrow button to select H Position and press lt gt Arrow button to set horizontal position of picture 2 Adjusting picture V Position Press V A Arrow button to select V Position and press lt gt Arrow button to set vertical position of picture 3 Adjusting Clock When PC is connected to TV set because of the difference of PC parameter you should adjust the Clock item in Window menu until you get a good picture 4 Adjusting Phase When PC is connected to TV set because of the difference of PC parameter you should adjust the phase item in Window menu until you get a good picture 5 Auto Adjust If there are unexpected problems happened when you adjust the items you ca
3. make sure to turn off the TV Before performing work spread cushioning over the base area to lay the LCD TV on This will prevent it from being damaged Hexagon bolt Stand Nylon gasket Nylon gasket Post Hexagon nut Figure 1 Figure 2 Assembling instruction 1 Unfasten the screw from the LCD TV Figure 1 2 Detach the Transition Board from the LCD TV Figure 1 3 Fix the stand and the Transition Board together with 4 screws 4 8 Figure 2 4 Screws into the holes and fix the stand and cabinet together Figure 3 22 If you have any problem check the countermeasure for each symptom listed below The following symptoms may have caused by inappropriate adjustment rather than actual malfunction of the unit If the trouble persists contact the service center Try another channel Poor picture and sound quality Adjust the antenna Check all wire connections Try another channel Press the TV AV button Make sure the TV is plugged in Check the antenna connections No picture or sound under TV status First check the volume of units connected to your TV Adjust the TV volume accordingly Check sound adjustment Volume and Mute No sound or sound is too low at maximum volume Make sure the program is broadcast in color Select the No color wrong colors or tints picture menu then adjust the color or tint submenu to the proper value Picture rolls ver
4. button to perform the exchange of channel number Adjusting the Picture Press MENU button on the remote control then press lt gt Arrowbutton to select Picture menu A 6 E iol AUDIO SETTING FUNCTION CHANNEL PICTURE MODE USER gt BRIGHTNESS CONTRAST SATURATION SHARPNESS BACKLIGHT COLOUR TEMP 4 STANDARD 4 gt ADJUST SELECT 1 Picture Mode Press V A Arrow button to select Picture Mode and press lt gt Arrow button to adjust picture mode to your desire Note Brightness Contrast Saturation adjusting are only available in user mode 2 Adjusting the Brightness of picture Press V A Arrow button to select Brightness and press lt gt Arrow button to adjust brightness to your desire 16 3 Adjusting the Contrast of picture Press V A Arrow button to select the Contrast then press lt gt Arrow button to set contrast to your desire 4 Adjusting the Saturation of picture Press V A Arrow button to select the Saturation then press lt gt Arrow button to set saturation to your desire 5 Adjusting the Tint of picture Press W Arrow button to select the Tint then press lt gt Arrow button to set tint to your desire Note Only available in NTSC 6 Adjusting the Sharpness of picture Press V A Arrow button to select the Sharpness then press lt gt Arrow button to set sharpness to your desire 7 Adjusting the Backlight of pict
5. is started Press V A Arrow button to change the subcode pages 28 Red Green Yellow Blue Command These four buttons are used to request linked page number with the current page 29 INDEX Press INDEX button then index page displays 30 MIX Press MIX button the teletext page changes transparent TV content and teletext page contentwill display at the same time Press MIX button again to exit mix mode 31 REVEAL Some pages contain hidden information The hidden text is displayed if the REVEAL button is pressed The hidden text will be cancelled when another page is requested if a different subpage is broadcasting or if the REVEAL button is pressed 32 CANCEL Press CANCEL button will remove all teletext display from the screen If the system was already under cancel mode press this button again to return to full screen teletext display Note Teletext function is optional 24 32 buttons on the remote control are only available for teletext function please check if your product has teletext function 12 Turning the TV On and Off 1 2 Press POWER button to turn power on If TV is in standby mode please press POWER button on the remote control to turn it on The indicator will switch from red to blue If you want to stop watching TV or go out for a while you can press POWER button on the re mote control If you want to watch TV again you can press this button again Unplug
6. PC NO SIGNAL SLEEP SLEEP TIMER TXT LANGUAGE 1 DNR Press lt gt Arrow button Adjusting DNR option it can improve the picture sharpness Note DNR is only available in TV mode 2 3D DLC 3D DLC is to automatically detect distribution of inputted visual signal and adjust to create optimum luminance Press lt gt Arrow button Adjusting 3D DLC option 3 OPC Press V A Arrow button to select OPC and press lt gt Arrow button to select off or Demo Note OPC is not available for VGA mode 4 Press V A Arrow button to select NO SIGNAL SLEEP and press lt gt button to select on or off 5 You can start a sleep timer by setting SLEEP TIMER a preset time 15MIN 30 MIN 45MIN 60MIN 90MIN 120MIN when the time has passed the TV will turn to standby mode automatically If you select OFF the timer doesn t work 6 TXTLANGUAGE Press W A Arrow button to select Txt Language in Function menu press lt gt Arrow button to select the teletext language to your desire Note TXT LANGUAGE setting is only available for teletext Teletext function is optional please check if your product supports teletext function VGA Adjust 1 Picture When the TV is in VGA mode press MENU button and lt gt Arrow button to select Picture MENU a PP Ed E AUDIO SETTING FUNCTION WINDOW PICTURE MODE USER gt BRIGHTNESS 50 CONTRAST 50 BACKLIGHT 50 COLOR TEMP gt
7. amplifiers that produce heat Place the apparatus in such a position that the screen is not exposed to direct sunlight It is best to have soft indirect lighting while watching and avoid complete dark environment and reflection from the screen as these may cause eye fatigue Keep the product away from high magnetic field i e power amplified power speaker to avoid affecting the tint Important Safety Instructions and Maintenance Installation Do not place the set on an unstable cart stand table or shelf The set may fall causing serious personal injury as well as damage to the product Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Do not place this apparatus near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or a swimming pool and the like When the TV being moved in from cold place it needs some right time for dew inside unit evaporating fully before turn on the unit To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions Unplug this apparatus from the AC outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for clea
8. as following SNOWY PICTURE Snowy picture is usually caused due to weak signal Adjust antenna or install an antenna amplifier DOUBLE IMAGES OR GHOSTS Double images are usually caused by reflections from tall buildings Adjust the direction of the antenna or raise it RADIO WAVE INTERFERENCE Wave pattern are moving on the screen which are usually caused by nearby radio transmitter or shot wave receiving equipment HIGH TEMPERATURE ELECTROTHERMAL INTER FERENCE Diagonal or herring bone patterns appear on the screen or part of picture is missing This is probably caused by high temperature electrothermal equipment in the nearby hospital NOTE If one of these symptoms appears on the screen when the cable from a company is connected this may be due to the local cable company broadcast 24 SuperMax CAHKYP MOOSA JUMA SANQOOR TRADING LLC A 2 19206 OAD 00971 4 2237433 00971 4 2237466 ecomax99 emirates net ae 39038986 SuperMax LCD Television SM2462HDK Operating instructions Keep this manual for future reference
9. controller DC 3V Two 7 batteries Power consumption 56W Dimensions TV with stand 579X209X414mm LXWXH Ty without stand 579X107X381mm Weight TV with stand 5 0 Kg Netwelght TV without stand 4 6 Kg Operation environment temperature 0 C 40 C Accessories Users manual Remote control Wall mounted accessories Two wall mounted brackets four fixed screws and four fixed sleeves Optional Note 1 Due to TV may be used with different display screen weight marked in this user s manual or in packaging box are subject to change without notice 2 The illustrations and on screen displays in this user s manual are for explanation purposes and may vary slightly from actual operations In case of any design change a notice will not be released 6 Power indicator IR remote sensor Input select Menu Program up down Volume up down Standby Headphone Power switch i Power switch Press this button to tum TV on or off Power indicator Green Normal playing status Red Standby status IR remote sensor Point remote control at this sensor to conduct remote control VOL gt lt Press these two buttons to increase or decrease the volume or operate menu PROG A V Press these two buttons to select channel or operate menu MENU Press this button to display OSD menu POWER Press th
10. ct NICAM use lt gt Arrow button to adjust to your desired OSD Setup Press MENU button on the remote control and press lt gt Arrow buttonto select Setting menu he r E p PICTURE AUDIO FUNCTION CHANNEL LANGUAGE SCREEN SAVER OSD POSITION DURATION HALFTONE COLOR SYSTEM ENGLISH OFF MID ALWAYS OFF AUTO lt 4 4 4 4 4 4 gt ADJUST SELECT EXIT 1 OSD Language Press V A Arrow button to select LANGUAGE and press lt gt Arrow button to select language you desire 2 Adjusting screen saver Press V A Arrow button to select SCREEN SAVER and press lt gt Arrow button to select OFF BLACK or BLUE 3 Adjusting OSD Position Press W A Arrow button to select OSD POSITION and press lt gt Arrow button to select MID LEFT LEFT BOTTOM RIGHT TOP or RIGHT BOTTOM 4 Adjusting Duration You can select ALWAYS 5s 10s or 15s 5 OSD Halftone Press W A Arrow button to select HALFTONE press lt gt Arrow button to select ON or OFF 6 Selecting color system You can select AUTO PAL SECAM NTSC NTSC443 But it s only available in AV and S VIDEO 18 Basic operation to be continued Function setup Press MENU button on the remote control or TV side panel press lt gt Arrow button to select Function menu PICTURE AUDIO SETTING DNR 3D DLC O
11. emove the lid of the battery compartment 2 Insert 2 size AAA batteries with polarities as indicated inside the compartment 3 Replace the lid Remote control introduction 1 LED Press any button the led will light 2 POWER Press this button to switch to standby mode and press it again to turn TV on 3 TV Switch to TV mode directly 4 YPbPr Switch to YPbPr mode directly 5 PC Switch to PC mode directly 6 HDMI Switch to HDMI mode directly 7 INPUT This button is used to switch among different sources 8 SOUND This button is used to select the sound mode Standard News gt Music gt User 9 PICTURE This button is used to adjust user picture mode press this button repeatedly and select one of four settings Dynamic gt Mild gt User gt Standard 10 ZOOM This button is used to set display window 11 Digital buttons 0 9 To select channel with digital buttons 12 INFO The button is used to display current channel information 13 RECALL To swap to the previous program you wanted from current program 14 FREEZE This function is no available for this model 10 15 SLEEP TV will turn to standby mode automatically at preset sleep time if you have set sleep timer Use your remote control to set the sleep timer Press SLEEP button on the remote control then press this button again to set sleep timer 15 Min 30 Min 45 Min 60 Min 90 Min 120 Min when you se
12. follows Press W Arrow button to select Color System under Channel menu and then press lt gt Arrow button to change video format as follows AUTO PAL gt SECAM Setting sound system Press MENU button on the remote control and then press W AArrow button to select Sound System under the Channel menu then press lt gt Arrow button to select sound system as follows AUTO BG 2 I DK Tuner setup Press MENU button on the remote control then press 4 Arrow button to select Channel 2 H A e FUNCTION d PICTURE AUDIO SETTING CHANNEL COLOR SYSTEM SOUND SYSTEM SKIP FINE TUNE 1 AUTO AUTO OFF 63 25MHZ AUTO SCAN MANUAL SCAN SWAP 4 gt ADJUST SELECT EXIT 1 Channel Press V A Arrow button to select Channel you can see the current channel number 2 Color System Press V A Arrow button to select Color System and press lt gt Arrow button to select the right color system 3 Sound System Press V A Arrow button to select Sound System and press lt gt Arrow button to select the right sound system 14 4 SKIP Press V A Arrow button to select SKIP then press lt gt Arrow button to select On or Off 5 Fine Tune In case of bad image or sound of TV program you can use Fine Tune function to obtain satisfying image or sound with operating steps as follows ii Press W A Arrow button to select Fine Tune and
13. is button to enter standby mode under normal play and press this button to enter normal play mode under standby mode INPUT Press this button to display the selectable signal source for main source 9 AUDIO R amp L Audio input sockets R amp L 10 VIDEO 2 Video input socket 11 HEADPHONE Headphone audio output socket L COMPONENT IN AV OUT R L Y PriCr R Lg VIDEO CTE TRF IN VGA PC e e e0o00 0 o oe e HDMI S VIDEO Connect to the HDMI jack of a device Connect an S VIDEO signal from a with an HDMI output camcorder or VCR VGAIPC IN Y Pb Cb Pr Cr Connect to the video output jack on Connect to YPbPr YCbCr video your PC RF IN AV AUDIO OUT Rei to an antenna or cable TV Audio out for external devices PC AUDIO IN Audio input for external devices AV VIDEO OUT Video out for external devices COMPONENT AUDIO IN Connect Component audio COMPOSITE amp S VIDEO AUDIO Audio inputs for external devices COMPOSITE VIDEO 1 Video input for external devices such as a camcorder or VCR 00 86 oO Overview Remote control LED POWER YPbPr PC TV HDMI INPUT ZOOM DIGITAL BUTTONS INFO RECALL SLEEP NICAM FREEZE MUTE VOLUME UP PROGRAM UP VOLUME DOWN PROGRAM DOWN ARROW BUTTONS OK 45 a v MENU EXIT HOLD SIZE TV TEXT SUBCODE FAST TELETEXT INDEX CANCEL MIX REVEAL Loading batteries 1 R
14. lect OFF the function is closed Press MENU button to exit when you have set the sleep timer Note The sleep timer you have set will be cancelled when the TV turns off or if a power failure occurs 16 NICAM The button is used to set NICAM sound system 17 MUTE Press this button to shut off the sound and press it again to restore TV sound 18 VOLA and VOLV Press these buttons to adjust TV volume 19 PROGA and PROGV Press these buttons to change channel upward or downward 20 Arrow buttons 4 pva To move cursor left right down up 21 Validation key 22 MENU Press this button to display main menu or exit the menu 23 EXIT To exit current menu 24 TV ITEXT Press this button to open or close teletext 11 25 HOLD Press HOLD button to toggle Hold function on or off When Hold is switched on the page acquisition is stopped When Hold is switched off the page acquisition is started 26 SIZE This is a toggle functin among 3 different size Normal Size Top half gt Bottom half Normal size Display full screen in normal size Top half Display the upper half of the screen in double height Bottom half Display the lower half of the screen in double height 27 SUBCODE Subcode mode gives the possibility to select certain subcode pages of a Teletext page Entry of digits within the range 0 9 for current subcode entry If the digit com pletes the entry a page request
15. n select the Auto Adjust and press Arrow button the TV set will resume the original settings Note Only H Position and V Position are available for Ypbpr mode 20 Antenna connection Antenna input impedance of this unit is 7bohm VHF UHF 75ohm coaxial cable can be connected to the antenna jack directly if the antenna cable is a 300ohm flat feeder cable you need to use the 3000hm 75ohm converter to connect the antenna cable to the antenna jack 3 0 OQ FLAT FEEDER UsE7 50 3000 750 COAXIAL CABLE 09 o ANT INPUT 75 Q Standard coaxial type 759 coaxial cable is recommended to eliminate interference and double image due to the unmatched input impedance of the antenna The antenna cable and power line should not be bundled together Stand and Wall mounted Optional 1 How to mount the LCD TV 1 Take out the bracket hole cover from groove with screw driver and place on the bracket hole 2 Fasten 4 screws into four nuts on the rear cover 3 Fasten 2 brackets with 4 M8 screws on the wall as figure 2 shown 4 Carefully check for the strength before releasing the LCD TV 400mm EE LJ pm E E e N R Q SS Lej 1 Figure 2 21 2 How to assemble the stand Before attaching detaching the stand
16. ning For your protection please read this instruction completely and keep this manual for future reference General description 5 Specifications and accessories 6 Overview 7 Basic operation 10 External connection 21 Trouble shooting 23 Picture defects and countermeasures 24 Feature Zero X radiation complies to green environment protection requirement Auto tuning and fine tuning Two composite video input socket One S Video input socket One PC VGA input socket One YPbPr input socket One HDMI input socket HDMI 1 3 Headphones Teletext Optional NICAM Multi language OSD Programmable TV sleep timer No signal automatic power off function 256 total channels to preset PC VGA mode VGA SVGA XGA WXGA YPbPr mode 480i 480P 576i 576P 720P 1080i 1080P HDMI mode 480P 576P 720P 1080i 1080P Note 1 In case of any design change a notice will not be released 2 The composite video output function only support TV and AV input Specifications Description SM2462HDK Display Screen Type Color active matrix LCD display Display size 59cm Diagonal max The maximum resolution 1920X1080 Image control Fine digital control Power supply AC 110 240V 50 60Hz TV receive system PAL I B G D K SECAM D K B G Frequency range CATV 470MHz Video in NTSC3 58 NTSC4 43 Antenna input impedance 750 Unbalance Sound output 4WX2 Power supply for remote
17. press lt gt Arrow button to conduct fine tuning from high frequency to low frequency or from low fre quency to high frequency till best picture or sound effect is obtained 6 Auto Scan Press V A Arrow button to select Auto Scan then press lt gt Arrow button to start auto search AUTO SCAN CH 1 77 25MHZ mm O0 ll TV will tune automatically and all programs found will be saved Please don t interrupt it Note i If you use the TV for the first time you must use Auto Scan to search and memorize all channels ii If your TV is not in TV input state you must switch it to TV state at first iii If you want to stop the process of Auto Scan just press MENU button to exit 7 Manual Scan Press W Arrow button to select Manual Scan and press lt gt Arrow button to enter manual search menu MANUAL SCAN CH 1 77 25MHZ ee TV will tune from lower frequency to higher frequency when you press Arrow button and from higher frequency to lower frequency when you press 4 Arrow Basic operation to be continued 8 SWAP CURRENT CHANNEL TARGET CHANNEL and EXCHANGE are used to swap two programs numbers A e S E PICTURE AUDIO SETTING FUNCTION TARGET CHANNEL EXCHANGE 4 gt ADJUST SELECT a Current Channel Press lt gt Arrow button to adjust current channel number b Target Channel Press lt gt Arrow button to adjust target channel number c Exchange Press lt gt Arrow
18. the power cord when the TV will not be used for a long period time Auto power off If the TV is under no signal sleep on it will enter standby mode automatically If the TV is non signal at VGA mode it would turn to standby in 15 seconds If the TV is non signal at other sources it would turn to standby in 5 minutes Memorizing the Channels Your TV can memorize all of the available channels After the available channels are memorized use PROG A V button to browse channels Language select Before using TV you can set the language 1 Press MENU button on the remote control then press lt p gt Arrow button to select Setting menu as following PICTURE AUDIO CHANNEL LANGUAGE ENGLISH gt SCREEN SAVER OFF gt OSD POSITION gt gt gt DURATION 4 ALWAYS HALFTONE OFF SELECT Note When you use OSD to adjust the TV you should notice The function which displays in gray is not available in current mode If you press V A button to select an item this function will be skipped automatically 13 2 Press A Y Arrow button to enter the submenu and press lt gt Arrow button to select the language you desire Selecting input source Press INPUT button on the remote control then you can select input sources as follows TV gt AV1 2 AV2 S VIDEO gt YPBPR 2HDMI VGA Setting color system In order to meet the video format in your country you can set the video format as
19. tically Check all wire connections Blurred or snowy picture distorted Check the direction location and connections of your antenna sound This interference is often due to the use of an indoor antenna Replace the remote control batteries Check the battery terminals Remote control malfunctions Remote is out of range move close to TV Confirm there is no obstructions between remote and TV Make sure power cord is plugged in Adjust the horizontal and vertical position When cleaning the LCD screen please pull out the power plug use dry and soft and clean cloth to clean the dust on the Clean TV set screen and shell In case of further cleaning for the screen please use clean wet cloth Do not use naphtha thinner or similar liquids for cleaning This product adopts a high resolution LCD TV and the colored point of some pixels may occur due to the special feature of the product For a few of colored points this shall not be related with terrible product performance or product reliability and in case of this situation the service of the product will not be influenced For the criterion of colored points our company has similar products with others The colored point in conformity with the product criterion is not covered by the return scope of the product due to quality problems We hope our respected customers will forgive us Colored point 23 The most common types of television interference are
20. ure Press V A Arrow button to select the Backlight then press lt gt Arrow button to set backlight to your desire Note Backlight function is only available for models with this function 8 Adjusting the Color Temp of picture Press W Arrow button to select the Colour Temp then press lt gt Arrow button to set colour temperature to your desire 9 Adjusting the Scale Mode of picture Press V A Arrow button to select the Scale Mode then press lt gt Arrow button to set scale mode to your desire Note It is useless under no signal mode Adjusting the Sound Press MENU button on the remote control then press 4 Arrow button to select AUDIO menu 5 E PICTURE SETTING FUNCTION CHANNEL SOUND MODE STANDARD gt EQUALIZER 4 ADJUST SELECT EXIT 1 Adjusting Sound Mode Press W Arrow button to select Sound use lt gt Arrow button to adjust sound mode 2 Adjusting Equalizer Press W AArrow button to select EQUALIZER and press lt gt button to enter submenu press V A button to select a cirtain frenquency and use lt gt button 17 to adjust its value 3 Adjusting Balance of sound Press W A Arrow button to select Balance use lt gt Arrow button to adjust sound balance 4 Adjust AVL mode Press V A Arrow button to select AVL use lt gt Arrow button to select on or off 5 Adjust NICAM of sound Press W A Arrow button to sele
21. use To be completely disconnected the apparatus from supply mains the mains plug of the apparatus shall be disconnected To avoid the fire no naked flame source such as lighted candles should be placed on the apparatus Important Safety Instructions and Maintenance Important Safety Instructions Installation An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Always turn the set off when it is not being used Unplug the apparatus from the AC outlet when it will not be used for a long period of time And when there is a lightning unplug the unit from the AC outlet immediately Never touch the antenna wire during lightning Do not pull the plug out by the wire Never touch the plug with wet hands Excessive sound pressure from earphones and headphones can cause hearing loss The ventilation should not be impeded by covering the ventilation opening with items such as newspapers tablecloths curtains etc At least 10 cm space should be left around the apparatus for sufficient ventilation The product should be situated away from heat sources such as radiators heat registers stoves or other products including
Download Pdf Manuals
Related Search