multifunctional digital color systems
Contents
1. an option Changing Scan Settings 11 Bl Image Settings tab On the Image Settings tab you can make the following settings The defaults are underlined 1 Exposure This setting sets the exposure for scanning Auto Select this option to automatically set an appropriate exposure for scanning Manual Select this option to manually set the exposure When you do this select from 5 lowest to 5 highest in increments of 1 on the slide bar 2 Background Adjustment This setting sets the contrast of the background color for scanning Select from 4 lowest to 4 highest in increments of 1 on the slide bar 3 Sharpness This setting is used for emphasizing or blurring the outlines of the scans Select from 4 smoothest to 4 sharpest in increments of 1 on the slide bar 4 Contrast This setting specifies the contrast of your scans Select from 4 lowest to 4 highest in increments of 1 on the slide bar 12 Changing Scan Settings Bl Color Settings tab On the Color Settings tab you can make the following settings 1 Saturation This setting specifies the saturation of your scans Select from 3 dullest to 3 brightest in increments of 1 on the slide bar 2 RGB Adjustment This setting specifies each density of red R green G and blue B in scanned images Select from 4 lowest to 4 EN highest in increments of 1 on the slide bar Changing Scan Settings 13 Scanning Originals on Multipl2. off line mode If it is in off line mode change it to on line mode 4 Make sure that the SNMP settings are correctly set EN P 16 Changing SNMP settings 5 Make sure that the MFP is correctly connected to the network pm Tip A device connection failure may also occur when too many computers try to connect at the same time Please try again later Cannot acquire my scans 18 Problem description I cannot acquire my scans using the Remote Scan driver Corrective action If your MFP is not ready for the Remote Scan operation you cannot acquire your scans using the Remote Scan driver The Remote Scan operation cannot be performed under the following conditions A paper jam occurs Aserviceman call occurs Copying scanning faxing or user function setting is being performed Any ofthe covers is open Originals are placed in the Reversing Automatic Document Feeder while it is opened In some MFP models the Reversing Automatic Document Feeder has been installed as an option Remote Scan Driver Errors OME100072H0 MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS MULTIFUNCTIONAL DIGITAL SYSTEMS Remote Scan driver Help TOSHIBA TEC CORPORATION 1 11 1 OSAKI SHINAGAWA KU TOKYO 141 8562 JAPAN QUALITY SERVICE R100520J2009 TTEC Ver08 F 2013 05 2012 2013 TOSHIBA TEC CORPORATION All rights reserved
3. selected you need to specify detailed search conditions for MFPs on the network Search local subnet Select this option to search for MFPs in the local subnet When this option is selected select IPv4 or IPv6 check box for specifying the preferred protocol Specify a range Select this option to search for MFPs in a specific range of IP addresses When this option is selected select IPv4 or IPv6 check box and enter IP addresses in the From and To boxes to specify the range 3 SNMP Settings Click this button when you need to verify and or change the SNMP settings CH P 16 Changing SNMP settings Changing Network Discovery Settings 15 ll Changing SNMP settings If you cannot find the target MFPs on your network the problem may be with SNMP settings Verify the correct SNMP settings in the SNMP Settings dialog box and change the settings if needed The dialog box can be accessed by clicking SNMP Settings on the Manual Selection GJ P 7 or the Discovery Settings P 15 dialog box Ask the administrator for details on the SNMP Network settings configured for your MFP 1 Version Be sure to have the correct SNMP version set for your MFP and select from the following options V1 V2 Select this option to enable SNMP V1 and V2 V3 Select this option to enable SNMP V3 V1N2N3 for Discovery Settings dialog box only Select this option to enable SNMP V1 V2 and V3 2 SNMP V1 V2 Community Name lf a comm
4. verify and or change the settings using the SNMP Settings dialog box For help see the following section P 16 Changing SNMP settings From the list of found devices select the name of your MFP and click OK The Remote Scan driver connects to the selected MFP and displays the e STUDIO Remote Scan driver window Tip When authentication screens appear enter the necessary information below to log on to the MFP For details ask the administrator User management User name Password Domain Windows Domain Authentication only Department management Department code Entering IP addresses manually 1 Click Manual Selection The Manual Selection dialog box appears Connecting to MFP 7 Enter the following items as required and click OK IPv4 IP Address Select this option to specify the device in the IPv4 address If this option is selected enter the IPv4 address of your MFP IPv6 IP Address Select this option to specify the device in the IPv6 address If this option is selected enter the IPv6 address of your MFP Name Enter the name of your MFP Location Enter the location of your MFP SNMP Settings Click this button when you need to verify and or change the SNMP settings P 16 Changing SNMP settings You must fill in the Name and IP Address boxes 3 The device specified in step 2 is added to the list Select the name of the added MFP and click OK The Remote Scan driver connects t
5. TOSHIBA Leading Innovation gt gt gt MULTIFUNCTIONAL DIGITAL COLOR SYSTEM S MULTIFUNCTIONAL DIGITAL SYSTEMS Remote Scan driver Help 2012 2013 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws this manual cannot be reproduced in any form without prior written permission of TTEC OVERVIEW This chapter provides an overview of the Remote Scan driver Features and Fu nctiois 3 nii ectas ocius aia e Da Eee ovx E oa ERAN EE cies cc Ma coa e ERE ENKER 2 System Requiremenlts rena n Ra ERR YR eR ER RAE NN YR ERR Re ERR RA RR AR YR RAE xy de 3 Features and Functions With the Remote Scan driver you can perform scanning operations remotely from your Windows computer over the TCP IP network Your scans can be loaded into a TWAIN compliant application P 5 BASIC OPERATION You can also make various scan settings to obtain scans that suit your preferences For details see the following section Q P 9 USEFUL FUNCTIONS AND SETTINGS 2 Features and Functions System Requirements The Remote Scan driver requires the following environments OS Windows 2000 Service Pack 4 Windows XP Service Pack 2 or later Windows Vista Service Pack 1 or later Windows 7 Windows 8 Windows Server 2003 Service Pack 2 Windows Server 2008 Service Pack 1 or later Windows Server 2012 Software TWAIN compliant application Micr
6. ab Image Settings Click to display the Image Settings tab Color Settings Click to display the Color Settings tab Scan Click to start remote scanning and acquire the image Close Click to close the Remote Scan driver Edit Reset Settings Click to reset all the settings to the factory defaults Devices Discovery Click to add a new MFP to connect to Clicking the menu displays the Local Discovery dialog box P 14 Registering additional MFPs Select e STUDIO Click to change the target device from which scans are retrieved P 14 Switching between connections Help Help Click to display Online Help About Click to display version information Page Settings Image Settings Color Settings Tabs You can set the various scan settings in each tab P 11 Settings tab P 12 Image Settings tab P 13 Color Settings tab Scan Click this button to start remote scanning and acquire the image Cancel Click this button to exit the Remote Scan driver Status Bar The status bar on the bottom of the dialog box shows the communication status and the IP address of the connected MFP 10 Changing Scan Settings Bl Page Settings tab On the Page Settings tab you can make the following settings The defaults are underlined 1 2 3 4 5 6 Original Size Select the size of the originals to be scanned Auto Select this op
7. e MFPs If your network has multiple MFPs you can search the network for additional connections Registering additional MFPs on the Remote Scan driver allows you to retrieve scans from each MFP P 14 Registering additional MFPs P 14 Switching between connections Registering additional MFPs To add a new connection click the Devices menu and select Discovery The Local Discovery dialog box appears in which you can register an additional MFP on your network For details see the following section P 7 Connecting to MFP Tip Once you register additional connections you can change the target MFP by selecting Devices gt Select e STUDIO CL P 14 Switching between connections Switching between connections Once you register multiple MFPs you can switch from one MFP to another and retrieve your scans from each device From the Devices menu select Select e STUDIC The Select Device dialog box appears 2 Select a MFP you want to connect to and click OK The target device is changed to the selected MFP e Studio Remote scan Driver dialog appears informing the user that a different product is selected and to start the acquiring operation again When authentication screens appear enter the necessary information below to log on to the MFP For details ask the administrator User management User name Password Domain Windows Domain Authentication only Department management Departmen
8. hod of selecting the device varies depending on your TWAIN compliant application 4 From the File menu select the menu to scan the original s The e STUDIO Remote Scan driver dialog box appears The menu for scanning the original s varies depending on your TWAIN compliant application f you are using the Remote Scan driver for the first time the Local Discovery dialog box appears In this case search the network for your MFP and establish a connection P 7 Connecting to MFP When authentication screens appear enter the necessary information below to log onto the MFP For details ask the administrator User management User name Password Domain Windows Domain Authentication only Department management Department code If you enter an invalid authentication password several times to log into the MFP you may not be able to log in for a certain period since it will be regarded as an unauthorized access 5 Change the scan settings as required and click Scan The equipment starts scanning the original s When the scanning is complete your scans are displayed in the application While scanning the originals the equipment displays Scanning and transferring on the touch panel To learn more about scan settings see the following section CH P 10 Changing Scan Settings 6 Scanning Documents Using the Remote Scan Driver Connecting to MFP When you use the Remote Scan driver and access your MFP fo
9. o the selected MFP displaying the e STUDIO Remote Scan driver window The target MFPs may not be found due to the SNMP settings In this case verify and or change the settings using the SNMP Settings dialog box For help see the following section CH P 16 Changing SNMP settings Tip When authentication screens appear enter the necessary information below to log on to the MFP For details ask the administrator User management User name Password Domain Windows Domain Authentication only Department management Department code 8 Connecting to MFP USEFUL FUNCTIONS AND SETTINGS This chapter describes useful functions and settings for the Remote Scan driver CHANGING Scan Setfings as uie teet irem nimii etd P Ba acc Eel HR a ab edo LLL axi bu dv E Ord re ER d Ran 10 Scanning Originals on Multiple MFPS rrrnnvvvvvnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnvnnnnnnennnnnnnnnnnnennennnnnnnnnnnn 14 Changing Network Discovery Settings rnrvvvnnnnnnnnnnnnnnnnvnnnnnnnnnnnnnvnnnnnnnnnnnnnnnvnennnnnnnnnnnnnnneen 15 Changing Scan Settings You can change the scan settings in the e STUDIO Remote Scan driver dialog box The dialog box consists of 3 tabs Page Settings Image Settings and Color Settings The components of the dialog box are as described below 1 2 3 4 5 Menu Bar You can select various functions from the following menus File Page Settings Click to display the Page Settings t
10. osoft Internet Explorer 5 5 Service Pack 2 or later for IPv4 environments Microsoft Internet Explorer 7 0 or later for IPv6 environments Recommended Memory Color documents at 400 dpi 256 MB Black documents at 600 dpi 256 MB Color documents at 600 dpi 512 MB Network TCP IP For instructions on how to install the driver refer to the Software Installation Guide or User s Manual Basic Guide Depending on your MFP model the OS supporting the Remote Scan driver can vary Refer to System Requirements given in the Software Installation Guide or User s Manual Basic Guide To use the Remote Scan driver the SNMP network service must be enabled The SNMP network service can be enabled on TopAccess For help ask the administrator System Requirements 3 BASIC OPERATION This chapter describes the basic operation of the Remote Scan driver Scanning Documents Using the Remote Scan Driver eene 6 Connecting Tereba 7 Scanning Documents Using the Remote Scan Driver With the Remote Scan driver documents set on the equipment can be scanned remotely from your computer Your scans are loaded into a TWAIN compliant application 1 Place the original s For help refer to the Copying Guide or User s Manual Basic Guide 2 Launch a TWAIN compliant application 3 From the File menu select the device used for scanning the original s Select e STUDIO Remote Scan driver The met
11. r the first time the Local Discovery dialog box appears In this case you can either use the local discovery feature to automatically search the network for your MFP or enter the MFP s IP address manually P 7 Searching MFPs automatically P 7 Entering IP addresses manually To find your MFP under the SNMP V1 V2 environment the community name set for the target MFP must be specified correctly For help consult the administrator Tip The following procedures can also be used for registering additional MFPs If you wish to scan originals remotely from multiple MFPs select Devices gt Discovery in the e STUDIO Remote Scan driver dialog box and follow the procedure below to register additional MFPs P 14 Registering additional MFPs Searching MFPs automatically Click Start Discovery The local discovery feature locates MFPs on the network Tips You can quit the process by clicking Stop Discovery Devices in different segments may not be found If you cannot find your MFP do so manually using Manual Selection P 7 Entering IP addresses manually The search process may take a long time especially when many clients exist on the network In this case change the discovery settings using Advanced P 15 Changing Network Discovery Settings The local discovery feature cannot detect MFPs on the IPX SPX network The target MFPs may not be found due to the SNMP settings In this case
12. t code 14 Scanning Originals on Multiple MFPs Changing Network Discovery Settings When you use the Remote Scan driver and connect to your MFP for the first time or when registering an additional MFP you need to find the target MFP on the network EN P 7 Connecting to MFP P 14 Registering additional MFPs The search process may take a long time especially when a number of clients exist on the network In this case you can narrow down the search conditions using the Discovery Settings dialog box In addition your attempt to find a MFP may fail due to the SNMP Network settings configured for the MFP In this case open the SNMP Settings dialog box and verify and or change the settings Q P 16 Changing SNMP settings Ask the administrator for details on the SNMP Network settings configured for your MFP To access the Discovery Settings dialog box click Advanced in the Local Discovery dialog box Make the following settings as required in the dialog box that appears 1 Devices Click the arrow button to display the drop down list box and select the check box es for the MFPs to be searched for 2 Network Enable IPX SPX Search This is disabled because the Remote Scan driver does not support the IPX SPX connection Enable TCP IP Search Select this option to search for MFPs on your TCP IP network This option is available only when the TCP IP protocols are installed on your computer When this option is
13. teps to resolve them If the problem persists after you have followed all of the steps make sure to note the name of your application what you are trying to do have done and any error messages and then contact an authorized dealer for further assistance P 18 Cannot find my P 18 Cannot connect to MFPs found by local discovery ED P 18 Cannot acquire my scans Tip For other problems see the Remote Scan driver s README file Cannot find my MFP Problem description cannot find my MFP using the local discovery feature Corrective action 1 Make sure that the MFP and your computer are correctly connected to the TCP IP network 2 If the MFP belongs to a subnet different from your computer s make sure that the default gateway setting is correctly set up 3 Make sure that the SNMP settings are correctly set P 16 Changing SNMP settings E Cannot connect to MFPs found by local discovery Problem description With the help of the local discovery feature have found the MFP but cannot connect to it Corrective action 1 If the network protocol is IPv4 make sure that Microsoft Internet Explorer 5 5 5 2 or later is installed If the network protocol is IPv6 make sure that Microsoft Internet Explorer 7 0 or later is installed Make sure that the Proxy settings on the Microsoft Internet Explorer are correctly set so that it can connect to the MFP Make sure that Microsoft Internet Explorer is not in
14. tion to automatically detect the original size Mixed Original Size Select this option to scan originals of mixed sizes Select Original Size Select this option to manually set the original size When this option is selected select the original size in the drop down menu Single 2 Sided Scan Select whether or not to scan 2 sided originals This setting applies only when the originals are set in the Reversing Automatic Document Feeder Single Select this option to scan only the front of originals 2 sided Book Select this option to scan both sides of originals in the same direction 2 sided Tablet Select this option to scan the front of originals in one direction and the back rotated 180 degrees Rotation Angle Select the rotation angle if you want to change the orientation of your scans Color Mode Select the color mode for scanning Original Mode Select from the following original modes Printed Image Select this mode to scan originals as printed images Text Select this mode to scan originals that contain text Photo Select this mode to scan originals that contain photos printed on photographic paper Text Photo Select this mode to scan originals that contain text and photos Blue Original Select this mode to scan originals that was printed with erasable toner Resolution Select the resolution for scanning In some MFP models the Reversing Automatic Document Feeder has been installed as
15. unity name other than public default is set for the SNMP community name for your MFP enter its community name To find your MFP under the SNMP V1 V2 environment the community name set for the target MFP must be specified correctly For help consult the administrator 3 SNMP V3 If SNMP V3 is enabled use the radio button to select the method for authenticating users User ID File Select this option when you want to use a user ID file Click Browse and specify the user ID file User Name Password Select this option when you want to use the user name and password When this option is selected enter or select each of the following items User Name Authentication Protocol Authentication Password Privacy Protocol Privacy Password f you select to enable SNMP V3 consult your network administrator for preliminary advice on how to authenticate users Each entry for User Name Authentication Password and Privacy Password can consist of up to 31 one byte alphanumeric characters 4 Restore Default Click this button when you want to reset all the settings back to the defaults 16 Changing Network Discovery Settings TROUBLESHOOTING This chapter addresses troubleshooting issues Remote Scan Driver Errors rannnnnuvnnuvnnunnnunnnunnnnennnennnnnnnnnnnnnnnnnnvnnnnnnnnenunnnnunnnunnnnennnnnnnennnennnen 18 Remote Scan Driver Errors This section describes the most common Remote Scan driver errors and provides s
Download Pdf Manuals
Related Search