User Menu
Contents
1. Attention This is Function 9 4 of ARS 2051F 5 10 4 Quick Erase HDD This function is used to quickly erase all data on the HDD Please backup any important data before using this function 9 04 Adv Setup Quick Erase HDD Press ENT to enter the following screen Use the Up and Down buttons to select the HDD to erase Quick Erase HDD ALL Target CH Press ENT again and the LCD will prompt you to confirm the erase operation All data will be lost Erase No Attention This is Function 9 5 of ARS 2051F 5 10 5 Full Erase HDD This function is used to full erase all data on the HDD Please backup any important data before using this function 9 05 Adv Setup Full Erase HDD Press ENT to enter the following screen Use the Up and Down buttons to select the HDD to erase Quick Erase HDD ALL Target CH Press ENT again and the LCD will prompt you to confirm the erase operation All data will be lost Erase No Attention The operation may take a long time and ARS 2051F does not have this function 24 SATA HDD Duplicate Controller Manual 5 10 6 H W Diagnostic Press ENT to enter the following screen This function is used to check that the system is operating normally 9 06 Adv Setup H W Diagnostic Press ENT again to enter the following screen The LCD will cycle through the test categories as they are performed The2. SATA HDD Duplicate Controller User s Manual Version 1 0 Attention Wait over 5 seconds to power on after shutdown to prevent the abnormal operation of the system ACARD eS TNO lO Gy Copyright 2010 ACARD Technology Corp Release April 2010 CE FE Copyright and Trademarks The information of the products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor who assumes no liability or responsibility for any errors that appear in this manual ACARD and SCSIDE are the trademarks of ACARD Technology Corp This manual contains materials protected under International Copyright Laws All rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of the manufacturer and author of this manual ACARD s SATA HDD Duplicate Controller is used for copying and editing personal audio and video data Violating Copy Right is a criminal act ACARD s Copy Controller only supports legal backup operation ACARD Technology Corp is not responsible for illegal recording Table of Contents Chapter TIA dree en e Asarco a 6 LA OVNI to dia 6 A a Nt lm cemented esa sce 6 TT E 6 1 4 System Requirements ccccococcnnncccnnconcnonononnnnonanennnonnonencnnos 6 Chapter 2 Installation 7 2 1 E E EE 7 2 2 ntal ARS 2055PF Aa teorico lao carta 8 2 3 Install ARS 2061F ni tadas 9 Chapter 3 Basic Instru
3. 6 07 Device Info 9 07 Load Default 6 08 System Info 9 08 Link Option 9 09 USB Auto Link 9 10 Copy HPA 14 SATA HDD Duplicate Controller Manual Here we take ARS 2055PF ARS 2061F to demonstrate 1 Copy HDD 2 Async Copy HDD 3 Compare HDD 4 Async Compare 5 PreScan Source 6 ReScan BUS 7 Source Size 8 Setup 9 Adv Setup 8 01 Language 8 02 Copy Size m 8 03 Startup Menu 9 01 Read Error Skip 8 04 Auto Compare 9 02 Update Firmware 8 05 Button Sound 9 03 Compare Firmware 8 06 Device Info 9 04 Quick Erase HDD 8 Setup 8 07 System Info 9 Adv Setup 9 05 Full Erase HDD 8 08 Fast Copy 9 06 H W Diagnostic 8 09 Auto Start Drive 9 07 Load Default 8 10 Auto Start Timer 9 08 Copy HPA 8 11 Tolerance Size 9 09 Burn In 8 12 BootTime Delay 8 13 Quick Compare If you have any questions regarding the LCD display info during use please refer to Appendix A Provided below is a detailed description of each function 15 SATA HDD Duplicate Controller Manual Here we take ARS 2061F to demonstrate 5 1 Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disk Please make
4. Compare HDD is used to see if the data on a source hard disk is identical to the target hard disk after the Copy HD operation Choose option 3 from the menu 3 Compare HDD HDD 11 232 9GB Press ENT to begin the comparison The LCD will display the following info Comp 23MB s 0 232 9GB 00 00 00 Once the comparison is complete the LCD will display the following info as well as the amount of data on the source hard disk Compare OK 11 Fail O Diff 0 Attention This is Function 2 of ARS 2051F 5 4 Async Compare This option allows the comparison process can increase the extra hard disk devices Choose option 4 from the menu 4 Async Compare HDD 11 232 9GB Press ENT to begin the async comparison The LCD will display the following info ACmp 23MB s 0 232 9GB 00 00 00 If the comparison process to continue to add additional hard disk device LCD will only show the last completed percentage Once the copying process is complete the LCD will display the following results Compare OK 11 Fail 0 Diff 0 5 5 PreScan HD PreScan HD is used to check if the source hard disk can be accessed properly It also tests the read speed Choose option 5 from the menu 5 PreScan Source HDD 11 232 9GB Press ENT to begin scan The LCD will display the following info Scan 90MB s 1 230 6GB 00 00 27 17 SATA HDD Duplicate Contro
5. Up and Down arrow keys to choose whether button sound is on or off Button Sound On Attention This is Function 6 6 of ARS 2051F 5 8 6 Device Info This option is used to display the details of all hard disks connected to the copy controller 8 06 Setup Device Info Press ENT and the LCD will display each hard disk information in order as shown below O Source CH 0 Hitachi 232 9GB Attention This is Function 6 7 of ARS 2051 F 5 8 7 System Info This option displays system information 8 07 Setup System Info Attention This is Function 6 8 of ARS 2051 F 5 8 8 Fast Copy This option displays Fast Copy 8 08 Setup Fast Copy Press ENT and the LCD will display the following info Use the Up and Down arrow keys to choose whether fast copy is on or off This function currently only effective in FAT FAT32 NTFS HFS Ext2 and Ext3 partitions Fast Copy On Attention This is Function 8 of ARS 2051F currently do not support HFS 20 SATA HDD Duplicate Controller Manual 5 8 9 Auto Start Drive This option is used to display to copy automatically once you insert HDD on target port 8 09 Setup Auto Start Drive Press ENT to enter the following figure The default is Off Use the Up and Down arrow keys to choose 1 11 Auto Start Drive Off 5 8 10 Auto Start Timer This option is used to display to copy automatically
6. alle naar Nederland ge xporteerde ACARD producten U kunt uw afgedankt ACARD product naar uw locale inzamelplaats brengen Elektrik ve Elektronik Madde At klar Demeci Elektrik ve electronik madde at klar n n yukselmesiyle basedebilmek arazi doldurma ve cop yakma f r n kullan m n azaltmak atik madde zararlar n n cevreye yay lmas n onlemek icin Avrupa Birligi AB ureticilerden elektrik ve elektronik madde at klar n gerektigi gibi toplamalar n geri donusturmelerini ve kimyasal isleme tabi tutmalar n talep etmek icin Elektrik ve Elektronik Madde At klar uzerine bir direktif haz rlad Topluluk uyeleri 13 Agustos 2005 ten once elektrik ve elektronik madde at klar n n ucretsiz geri donusum sistemlerini coktan olusturmuslard Bundan dolay ACARD Almanya ya ihrac ettigi butun urunlerin geri donusumunden sorumludur ACARD urunleri geri donusum gerektirirse yerel toplay c lara geri verebilirsiniz WEEE GtoneTeHb UTO6bl cllpaBUTbCA C YBENUYUBaIOLUMMCA HEHYKHbIM INEKTPUYECKUM N INIEKTPOHHbIM o6opyAoBaHuem YMeHBLUUTeE UCNONb3OBaHUe 3akKanbIBAHNA Mycopa n NCNONb3OBAHNA YCTAHOBKU Ana CKUTaHua OTXOACB MPenaTcTByUTe BpeaHomy BbIOpocaM 3arpa3gHaTb OKpykaHOBKU Cpeny EBpone cku coto3 EC ycranoBun AupekTuBy no HeHykHoMy OnekTpnyeckomy n InekTpoHHoMy O6opyaocBaHuto WEEE ana Toro 4TOGbI U3roToBUTene coOpann nepepabaTbiBanm n BOOLE NPOABUNN BHNMAHNE K HEHYXKHOMY 3INEKTPUYHECKOMY N 3J1IEKTPOHHOMY o6opyAoBaHut GOMKHb
7. matches the product Prepare 1 Source HDD for the SATA port and 11 Target HDDs The capacity of the target HDDs must be equal or higher than the source HDD The ARS 2061F supports twelve SATA connections the blue port Source and the black port Target Please refer to the manufacturers instructions for further details Please also make sure that the PSU supplies enough power SATA HDD Duplicate Controller Manual Installation Procedure 1 Connect the source HDD with the SATA 2 Connect the target HDDs with the SATA cable to the CN2 UP blue port on the ARS cable to the black port on the ARS 2061F 2061F 3 Connect the power cable to CN8 large 4P 4 Shown below is an ARS 2061F with all the power port on the ARS 2061F equipments properly wired 10 SATA HDD Duplicate Controller Manual Chapter 3 Basic Instructions 3 1 Buttons and LCD There are four buttons and an LCD on the panel of SATA HDD Duplicate Controller 3 5 1 It shows a function or a message 2 It s used to scroll up function menus 3 It s used to scroll down function menus 4 It s used to execute a function 5 It s used to cancel a function 3 2 LCD Configuration Chart Here we take ARS 2061F to demonstrate 1 2 ACARD Technology Initialize SDRAM 2061F Ver 1 25P Figure 1 shows the firmware version of ARS Figure 2 shows Initialize SDRAM s status 2061F 3 4 Detect Drives 1 Copy HDD
8. sure that the capacity of the target hard disk is equal or larger than the source hard disk Choose option 1 from the menu 1 Copy HDD HDD 11 232 9GB Press ENT to begin copy The system will auto detect the hard disks and show the following copying info on the LCD Copy 36MB s 0 232 9GB 00 00 00 The LCD will show the following info during the copying process elapsed time completed percentage The copy speed capacity and time will vary depending on the source hard disk Once the copying process is complete the LCD will display the following results Copy HDD OK 11 Fail 0 5 2 Async Copy HDD This option allows when the replication process can increase the extra hard disk devices Choose option 2 from the menu 2 Async Copy HDD HDD 10 232 9GB Press ENT Before the start of the reproduction if the ARS 2061F to detect the eigth hard drive capacity is less than source then the LCD will show the corresponding channel number 8 Space Not Enough And then automatically copies The LCD will display the following info Acpy 36MB s 0 232 9GB 00 00 00 If the replication process to continue to add additional hard disk device LCD will only show the last completed percentage Once the copying process is complete the LCD will display the following results Async Copy HDD OK 11 Fail 0 16 SATA HDD Duplicate Controller Manual 5 3 Compare
9. DOT BUNIN eena A iets 26 5 10 10 Detect HDD Delay ccooonccncccconccncccconcnnnccnnnconnnnnnns 26 5 10 11 Link Option for USB mode ARS 2051F Only 27 5 10 12 USB Auto Link ARS 2051F Only 27 Chapter 6 Basic Troubleshooting nnnnnennonnnnnnennnennnnnnennennnni 28 EE EC EE 28 6 2 Error Message lies 28 A eoi re re eee hc pee we Mere eet ae nt eRe ee 28 SAMOS ceo oras Da ii a ori Diao La ee dices 28 6 5 Firmware Upgrade vincia tds 28 6 6 Elie tele EE 28 OF ADOQU GOD Y HFEA sarta 28 Appendix A LCD Messages cccccsseeceeeeeeeeceesseeeeeeseeaeeeeeseas 29 TECHNOLOGY ACARD WEEE Statement H O D Y WEEE Statement English In order to cope with the increasing waste electrical and electronic equipment reduce the use of landfill and incinerator and prevent the harmful matter of waste equipment from entering the environment the European Union EU has set the Directive on Waste Electrical and Electronic Equipment WEEE asking manufacturers to collect recycle and treat waste electrical and electronic equipment properly Member nations already established their free of charge recycle systems of WEEE before August 13 2005 Accordingly ACARD has to be responsible for recycling all products exported to Germany You can return your ACARD product that needs recycling to a local collector WEEE Erkl rung Mit dem Ziel die steigende Menge elektrischer und elektronischer Altger te zu bew ltigen ohne hierzu u
10. IM ODD 2OM Une Haunn ycTaHoBunn GecnnaTHyio CNCTeMy n NeEKTPOHHOMY O6OopygoBaHno AOJDKHBIM OOpa3om UnieHbl Hann ycTaHoBunn GecnnaTHyio cuctemy nepepa6oTtkn WEEE go 13 asrycra 2005 CootBetTcTBeHHO ACARD o6a3aH bITb OTBETCTBEHHbIM 3a TO YTO nepepa6oTtan Bce MpoAyKTbI 3KCNOPTNpyeMbIe B FepmaHuto Bol MOX Te BO3BpaTHTb Bal npogyktT ACARD koroppu HyYKAAETCA B peunpkynauna MECTHOMY COOpLuNkKy WEEE Statement Afin de g rer la quantit croissante de d chets lectriques et lectroniques de r duire l utilisation des d charges et des incin rateurs et d viter que des d chets nocifs ne polluent l environnement l Union Europ enne a publi la directive WEEE sur les d chets lectriques et lectroniques Celle ci sp cifie que les fabricants doivent collecter recycler et traiter l quipement lectronique et lectrique usag Depuis le 13 aout 2005 les pays membres ont mis en place un systeme de recyclage gratuit selon le WEEE De ce fait Acard est responsable du recyclage de tous les produits export s vers Allemagne Vous pouvez mettre au rebut votre equipement ACARD usag dans votre centre local de recyclage Pour plus d informations sur les lieux de mise au rebut des quipements usag s destin s au recyclage veuillez contacter votre mairie votre service de traitement des d chets m nagers ou le magasin OU vous avez achet le produit RAEE Spanish Con la finalidad de reducir el incremento de residuos el ctr
11. LCD display is tested first the control panel is tested next requires manual operation then followed by the system s internal diagnostics hardware connection test then the RAM and SD Flash test All test results are shown on the LCD This is a simple way to verify that the system is operating normally Press ENT and the system will begin the tests as shown below LCD Test Start Button Test gt SDRAM Test gt gt g8192kbytes OK Test IDE 0 1 FlashTest OK Test finished OK gt gt Once the system diagnostics have been completed the Test finished message will appear on the LCD 5 10 7 Load Default Press ESC to return to the main menu then use the ENT button to select This function resets all settings to their factory default This function helps the system recover from errors caused by an illegal operation 9 07 Adv Setup Load Default Press ENT to enter the following screen Use the Up and Down buttons to confirm reset to factory defaults Load Default Config Yes If Load Default OK this will be displayed on the LCD as shown below Load Default Ok Attention This is Function 9 7 of ARS 2051F 25 SATA HDD Duplicate Controller Manual 5 10 8 Copy HPA If this function is set to ON the system will completely copy the data in a source HDD s host protected area 9 08 Adv Setup Copy HPA The defaul
12. Please Wait HDD XXX XGB Figure 3 shows Detect Drives s status Figure 4 shows the first function Copy HDD There are 8 functions You can press W to see other functions 11 SATA HDD Duplicate Controller Manual Chapter 4 Board Layout The board layout of ARS 2051F is shown as follows E O E D Ke Pall O cy Ce 12 SATA HDD Duplicate Controller Manual The board layout of ARS 2061F is shown as follows 13 SATA HDD Duplicate Controller Manual Chapter 5 Functions The copy controller has 8 functions in total with the 8th Adv Setup being a hidden system function that only appears when the ESC key is pressed for 2 seconds until there is a beep These are shown below Here we take ARS 2051F to demonstrate 1 Copy HDD 2 Compare HDD 3 PreScan HDD 4 ReScan BUS Copy Controller 5 Source Size 6 Setup 7 USB Mode 8 Fast Copy 9 Adv Setup 6 01 Language 9 01 Detect HDD Delay 6 02 Copy Size 9 02 Read Error Skip 6 03 Startup Menu 9 03 Update Firmware 6 04 Auto Compare 9 04 Compare Firmware WE 6 05 Copy With Size 9 05 Quick Erase HDD 6 06 Button Sound 9 06 H W Diagnostic
13. aces 2051F 6 SATA interfaces 2055PF 12 SATA interfaces 2061F e 2 x16 LCD display e Thin film 4 button controls e 256KB 2051F 512KB 2055PF 2061F of FLASH memory for Copy Code e Firmware upgradeable via DVD ROM e Power Voltage 5V 5 Current 1 5A max e Environment Operating 0 C 60 C Non Operating 20 C 85 C e Humidity 15 90 e Dimensions 150mm W x 42mm H x 150mm D 2051F 2055PF 150mm W x 42mm H x 215mm D 2061F 1 4 System Requirements e Upright standalone external casing optional e 250W 300W or higher PSU optional e SATA cable 2051F 2055PF 2061F e Hard Disk optional e Hard Disk Rack optional SATA HDD Duplicate Controller Manual Chapter 2 Installation Please verify that the product includes all required accessories and the necessary equipment are available before installation 2 1 Install ARS 2051F The ARS 2051F is pictured below Before Installation Before connecting the power verify that the local power supply voltage matches the product Prepare 1 Source HDD for the SATA port and 1 Target HDD The capacity of the target HDDs must be equal or higher than the source HDD The ARS 2051F supports two SATA connections CN8 is the blue port Source and CN6 is the black port Target Please refer to the manufacturers instructions for further details Please also make sure that the PSU supplies enough power Installation Procedure 1 Connect the source HDD
14. atted hard disk at first Verify Disk or Partition Do you want to verify the hard disk or just a partition Verify Hard Disk Fait eenen The hard disk is not verified successfully 3 Audio Editing Burn or Move to PpartitiON csi initial EE Do you want to directly copy the data into disc or move them to the partition Can t edit HDD comicas atras The hard disk cannot be edited as a source audio disc Close all discesession 2 c cette cette ee eeeeettteeeeeeees Confirm the closing of disc sessions Continue edit next Disch Ask if you want to continue the music disc editing End edit disc and bum Finish the music disc editing and start to copy Erase selected Tracks Abort the selected tracks and delete them Ins empty disc Continue Do you want to insert a blank disc and continue copying Insert next OSO leen ee ee NEEN Insert the next audio disc NO AUDIO track in this diec ec cceeeeeeeeeeeeeeeeeeteees The source disc has no audio track Sessions were closed already The disc sessions have already been closed Target Overflow Re SelecL cociente ica alos The disc capacity is not enough to store the selected tracks Please select again Tot overflow del laSttrk lt cuado The disc capacity is not enough to store the selected tracks So do you want to delete the last track 4 Firmware Update Check Sum EFFE EES The udpated firmware has er
15. ctions coooonnnncnnnnnonononnnncnnnnnnnnnonononnos 11 3l B tONS aNG LOD tacones 11 3 2 LCD Configuration Chart 11 Chapter 4 Board Layout ek ENEE 12 Chapter 5 Functions ooooccccnnccccccconncnnnncconnnanncnnnnnnnnnnnnnnnnnncnnnnnnos 14 STCO HDD aea e a oe need nn ee Re ee 16 5 2 Async Copy HDD ARS 2055PF ARS 2061F only 16 53 Compare HDD aaee 17 5 4 Async Compare ARS 2055PF ARS 2061F only 17 O ee 17 5 0 Rescam eeneg 18 Def SOURCE HD SIZE EE 18 DO OA EE 18 58 Langa iii 19 A aeren eg 19 AN E N 19 5 8 4 Auto Compare ENEE 19 58 5 BUMOM SOUNO AAA A 20 5 8 6 Device NO EE 20 EAS an EE 20 EE rd a a 20 5 8 9 Auto Start Drive ARS 2055PF ARS 2061F only 21 5 8 10 Auto Start Timer ARS 2055PF ARS 2061F only 21 5 8 11 Tolerance Size ARS 2055PF ARS 2061F only 21 5 8 12 BootTime Delay ARS 2055PF ARS 2061F only 21 5 8 13 Quick Compare ARS 2055PF ARS 2061F only 22 5 8 14 Copy With Size ARS 2051F Only oooocccccccccnccccccc 22 5 9 USB Mode ARS 2051F Only couiosciiaiano conanccidia cards 22 510A SEUD toda 23 LO Read EOS pica Eege 23 5 10 2 Update Firmware ccccccssseeccccssseeeeceeeseeeesseaaeeeess 23 510 3 Compare Firmware caerse ea a i i 24 5 10 4 Quick Erase HDD EE 24 510 9 F l Erase HDD e ce oie revisa 24 5 10 6 H W DiagnostiC ccccccccccccccocccocenenenoneninininineninininines 25 ARA inten nl rere oreo 25 510 8 CODY een 26
16. e firmware was downloaded correctly A failed firmware upgrade may cause the ARS 2055PF to become inoperable If the system is working normally do not attempt this operation If the system is already experiencing problems please contact your distributor for repairs 6 6 Startup Shutdown Do not suddenly turn off the power while the system is performing an operation After shutting down normally wait a moment usually around 2 seconds before starting the system again so it can run its self diagnostics 6 7 About Copy HPA The HPA Host Protected Area is a hidden data region defined in ATA ATAPI 4 This area is not usually accessible to software The SATA HDD Duplicate Controller supports the copying of data from this hidden area 28 SATA HDD Duplicate Controller Manual Appendix A LCD Messages 1 Normal Conditions All data will be lost erase All data on the disc will be lost Confirm the erasing of data E ent EE tias Analyze the source disc Audio Disc Cantcomparel The system cannot compare the audio discs Cannot read TOG isc The system cannot read the contents of disc Check Target Please Wait 00000nnnneeeeeeeeeeeerrnr reesen The system is checking the target device Detect Drtves Detect what drives are connected with the system DVD RW does not Support the Func DVD RW doesn t support this function Erase FINISHOO cusco doit eee The erasing of data comes to an
17. ear in the main menu Attention This is Function 9 8 of ARS 2051F 5 10 12 USB Auto Link requires AEC 4420DX ARS 2051F Only This function sets the ARS 2051F to immediately enter USB mode on startup This allows direct control via PC as shown below 8 09 Adv Setup USB Auto Link Press ENT and the LCD will display the available options as shown below The default is OFF USB Auto Link OFF Attention This is Function 9 9 of ARS 2051F 27 SATA HDD Duplicate Controller Manual Chapter 6 Basic Troubleshooting 6 1 LCD If the LCD blank after the device is turned on check that the power cable is properly connected and that the power supply is on 6 2 Error Message When the system is running a copy operation or hardware diagnostics if the operation is manually terminated by pressing ESC an error message will be shown by the LCD This may lead to an illegal operation and cause the device to stop reminding If this happens the device must be restarted 6 3 Hard Disk If unable to read the hard disk please check that the data and power cables are properly connected 6 4 Keys If pressing the keys on the front panel produces no response from the system the keys may have malfunctioned Please check the control panel to see if the wiring has come loose 6 5 Firmware Upgrade The device can be updated to new versions of firmware through CD DVD ROM If unable to update the firmware check that th
18. end o ea aae ae tee nanan ae The system is erasing the data on the disc Fail to get Drive Info eerren The drive information cannot be obtained Fail to get Src Disc Info The information of source disc cannot be obtained Hold ESC TO OM EE Press ESC for a second to terminate the test e D A fo es vs fa cereus epee cache enue steric ta The comparison results are the same Initialize SDRAM Ms catarata Initialize the memory of the system Load Default Confg Do you want to load the default settings No Erasable Disc in DVD RW 00 coco The disc on the DVD RW device is not rewritable ln e Fn o a ra E E TE E A A aa The system is preparing to record Press a Key to Eject Fail Disc Press any key to eject the failed disc after copying Press a Key to Eject Good Disc Press any ket to eject the good disc after copying Read disc error orgue id During comparison the disc cannot be read Save new config Fall ooo The new setting of configuration cannot be saved Source Disc Empty caciones The source disc doesn t contain any data Source Disc Not Read Source disc is not ready to be read Source Drive Not Read Source drive is not ready to read Src amp Tgt can t in the same channel eee eee eteecaaaeeeeeeeeeeeteeeceaaeeeeeeeeeeenees eeh During comparison the source and target discs cannot be in the same channel Target Disc Not Empty cosmo aa The target disc stil
19. h errors 9 01 Adv Setup Read Error Skip Press ENT to enter the following screen By default this option is set to OFF Use the up and down buttons to enable or disable this option Read Error Skip Off Attention This is Function 9 2 of ARS 2051 F 5 10 2 Update Firmware This function is used to update the system s firmware Download the latest version of the firmware from the Internet at www acard com then write it on to a blank CD 9 02 Adv Setup Update Firmware Shut down the HDD cloner Restart the system and insert the CD with the latest version of the firmware into the DVD ROM Press ENT and the system will begin scanning for a new firmware version H found this will be displayed on the LCD as shown below Press ENT again to begin updating If the upgrade is successful the system will restart automatically Searching F W gt Upate F W X XX Please Wait To X XX gt Yes Attention This is Function 9 3 of ARS 2051 F 23 SATA HDD Duplicate Controller Manual 5 10 3 Compare Firmware This function is used to compare the current system firmware version with the new version the user is upgrading to This ensures that the downloaded firmware is the latest version The message Last update F W indicates that it is the latest version 8 04 Adv Setup Searching F W Last update F W Compare Firmware gt Please Want gt OK
20. icos y de material electr nico reduciendo el uso de los vertederos e incineradoras y prevenir el preocupante aumento del contacto de estos residuos con el medio ambiente Por este motivo la Uni n Europea ha fijado la Directiva de Residuos de Aparatos El ctricos y Electr nicos RAEE solicitando a los fabricantes la recolecci n reciclaje y tratamiento de ests residuos correctamente Los paises miembros ya han establecido su sistema de reciclaje gratuito de RAEE antes del 13 de Agosto del 2005 Por este motivo ACARD es el responsable del reciclaje de todos los productos exportados a Alemania Usted puede devolver su producto Acard a un punto de recogida local cuando desee reciclarlo Dichiarazione WEEE Per far fronte all aumento dei residui delle apparecchiature elettriche ed elettroniche ridurre l uso di materiale di riporto e degli inceneritori ed impedire che il materiale nocivo delle apparecchiature residue entri a contatto con l ambiente Unione Europea UE ha stabilito le Direttive sui Residui delle apparecchiature Elettriche ed Elettroniche WEEE chiedendo ai fornitori di raccogliere correttamente riciclare e trattare le apparecchiature elettriche ed elettroniche residue Le nazioni facenti parte dell Unione Europea hanno gi stabilito il loro sistema gratuito di riciclaggio di questo materiale WEEE prima del 13 agosto 2005 Di conseguenza ACARD responsabile del riciclaggio di tutti i prodotti esportati in Germania Potete re
21. l has data Target Disc Not Head Target disc is not ready to be written into Target Drive Not Head Target drive is not ready to write Target overflow The target disc hasn t enough capacity to store new data TOG Nol Mathias monetes The comparison results are not the same User e a EE Cancel the job during operation 2 Connecting with a HDD All data will be lost Tomat Ee All data on the hard disk will be lost Confirm the formatting of hard disk Delete Image in Partition xd Confirm the deleting of data image in partition xx Format HDD Ask if you want to format the hard disk Format HDD OKT The Formatting of hard disk has been completed HDD not Formal ciao altra The hard disk hasn t been formatted yet HDD too ET UE The capacity of hard disk is too small HDD too small to handle mmagel non nnnnnnnncnnnnnnnnnnncncnnn Ee The hard disk hasn t enough capacity to store the data image at least 5Gbytes Image Exists e E NEE GE There is a data image in the current partition Confirm the overwriting of data Image load Fail The image isn t successfully loaded from DVD to the hard disk Image load Ok The image is successfully loaded from DVD to the hard disk 29 SATA HDD Duplicate Controller Manual No Image in Partition xx There is no data image in partition xx No Valid HDD boot iia The system cannot find a hard disk Partition Eet The partition is damaged Select HD PES ada Select a form
22. ller Manual Once the scan is complete the LCD will display the corresponding results PreScan OK Attention This is Function 3 of ARS 2051F 5 6 ReScan Bus Choose option 6 from the menu 6 ReScan BUS Press ENT to re scan hardware The LCD will display the following info Re Scan BUS NOW Yes When the scan is complete the LCD will display the following info Bus re scan OK Attention This is Function 4 of ARS 2051F 5 7 Source Size Source Size is used to show the capacity message of the source hard disk Choose option 7 from the menu 7 Source Size Press ENT and the LCD will show the following info HDD Hitachi Size 232 9GB Then press ENT and the LCD will show the data s size info HDD Hitachi Data 200 9GB Attention This is Function 5 of ARS 2051F 5 8 Set up Setup allows various system settings to be changed There are 13 sub options Language Copy Size Startup Menu Auto Compare Button Sound Device Info System Info Fast Copy Auto Start Drive Auto Start Timer Tolerance Size BootTime Delay and Quick Compare Choose option 8 from the menu 8 Setup Attention This is Function 6 of ARS 2051F 18 SATA HDD Duplicate Controller Manual 5 8 1 Language This option is used to select the system s language support By default this is set to English Press ENT to change the Language settings La
23. nguage English 5 8 2 Copy Size This option is used to specify the size of the source hard disk for simplifying further copying operations 8 02 Setup Copy Size Press ENT and the LCD will display a detailed list of options as shown below Copy Size 100 1 MB Use the Up and Down arrow keys to choose different copy sizes The system will offer their corresponding percentages so the user can specify the amount to copy from the source hard disk Press ENT to confirm and save the changes 5 8 3 Startup Menu This option allows you to set an option other than Setup to be displayed as the first available option on the menu every time you start the system 8 03 Setup Startup Menu Press ENT then use the Up and Down arrow keys to choose other options By default the first menu option is Copy HDD Startup Menu 1 Copy HDD 5 8 4 Auto Compare This option automatically compares the source hard disk with the target hard disk after a copy operation is completed 8 04 Setup Auto Compare Press ENT to access option By default it is set to Off Use the Up and Down arrow keys to choose On Auto Compare Off 19 SATA HDD Duplicate Controller Manual 5 8 5 Button Sound This option is used to control the sound of a button when you press it 8 05 Setup Button Sound Press ENT and the LCD will display the following info Use the
24. nn tig M lldeponien und Verbrennungsanlagen zu belasten und um die Verschmutzung der Umwelt durch freiwerdende Stoffe aus den Altger ten zu vermeiden hat die Europ ische Union EU die Richtlinie ber Elektro und Elektronik Altger te erlassen Die Richtlinie verpflichtet Hersteller elektrische und elektronische Altger te umweltgerecht einzusammeln zu recyceln und zu entsorgen Die Mitgliedsstaaten der EU haben bereits ihre kostenfreien Recyclesysteme konform der WEEE vor dem 13 August 2005 eingerichtet Entsprechend der Richtlinie ist ACARD verantwortlich f r die umweltgerechte Entsorgung aller nach Deutschland exportierten ACARD Produkte Sie k nnen Ihr zu entsorgendes ACARD Produkt zu Ihrer rtlichen Sammelstelle bringen AEEA verklaring Met het doel de stijgende hoeveelheid afgedankte elektrische en elektronische apparatuur te beheersen zonder hiervoor onnodig stortplaatsen en verbrandingsovens te belasten en om de vervuiling van het milieu door vrijkomende stoffen uit de afgedankte apparatuur te voorkomen heeft de Europese Unie EU de richtlijn betreffende afgedankte elektrische en elektronische apparatuur besloten Deze richtlijn verplicht fabrikanten afgedankte elektrische en elektronische apparatuur in te zamelen te recyclen en te verwijderen De lidstaten van de EU hebben reeds de kosteloze recyclesystemen volgens de AEEA v r de 13 augustus 2005 ingericht Conform de richtlijn is ACARD verantwoordelijk voor de verwijdering van
25. once you insert HDD on target port 8 10 Setup Auto Start Timer Press ENT to enter the following figure The default is Off Use the Up and Down arrow keys to choose 5 Sec 50 Sec Auto Start Timer Off 5 8 11 Tolerance Size This option is used to do to ensure that when the target is smaller than the source can not be performed when the copy 8 11 Setup Tolerance Size Press ENT to enter the following figure The default is Off Use the Up and Down arrow keys to choose 1 100 of source Tolerance Size 1 4 7GB 5 8 12 BootTime Delay This option is used to to set boot delay time 8 12 Setup BootTime Delay Press ENT to enter the following figure The default is 5 sec Use the Up and Down arrow keys to choose 0 99 sec BootTime Delay 5 sec 21 SATA HDD Duplicate Controller Manual 5 8 13 Quick Compare This option is used to set the size of each comparison unit 8 13 Setup Quick Compare Press ENT to enter the following figure The default is Off Use the Up and Down arrow keys to choose 1 Byte 1K 10K 100K 1MB 10MB 100 Mbytes In order to improve the accuracy of pure data can maintain the default settings Quick Compare Off 5 8 14 Copy with Size ARS 2051F only This option is used to set the source hard disk with the target hard disk the same capacity after a copy operation 8 05 Setup Copy with Si
26. rors Flash ROM faill cacao mimco aran havent Kanna PENNAENN EEN E Data cannot be written into Flash ROM Invalid TIFMIWAre ooo ri The disc doesn t contain a valid firmware Last update F W Fall neeesser The firmware is not updated successfully Last update F W OKT The firmware is updated successfully A The system is searching for a valid firmware Source can t be Hard Disk During comparison the source cannot be hard disk 30 SATA HDD Duplicate Controller Manual Technical Support Form Email address support acard com Website http www acard com Model Name ex ARS 2061F Firmware version System Configuration Motherboard System model SCSI host adapter chip brand amp model SCSI host BIOS version Other VO card Operating System SATA HDD brand amp model SATA HDD capacity SATA HDD firmware Problem description r is required 31
27. stituire il vostro prodotto acquistato da ACARD che deve essere riciclato da un azienda specifica locale SATA HDD Duplicate Controller Manual Chapter 1 Introduction 1 1 Overview The three SATA HDD Duplicator models available are ARS 2051F 2055PF 2061F The ARS 2051F 2055PF and 2061F are standalone 1 to 1 1 to 5 and 1 to 11 SATA HDD duplicators All are equipped with an LCD display and touch buttons so HDD data can be duplicated quickly and conveniently without using a computer This makes them well suited for backing up personal and business data The IT industry can also use them for small scale data duplication In the past users looking to duplicate data on to multiple HDDs usually had to start up the computer then use writing software like Ghost This means time has to be spent on learning to use the software and then using it to copy data ACARD s answer is the SATA HDD Duplicator series that offers fast data backup 1 2 Features e SATA to SATA e g ARS 2051 F 2055PF 2061F HDD duplicators e Completely standalone SATA HDD duplicator with no additional hardware or software required e Support for high speed 1 to 1 ARS 2051F or 1 to 5 ARS 2055PF or 1 to 11 ARS 2061F HDD duplication e User friendly interface with LCD information display e Offers a range of options that extend the product s applications 1 3 Specifications e ACARD SOC processor e 8MB 2051F 64MB 2055PF or 128MB 2061F SDRAM memory e 2 SATA interf
28. t is OFF Use the ENT Up and Down buttons to change this to On USB Auto Link OFF Attention This is Function 9 10 of ARS 2051F 5 10 9 Burn In This function is used to burn test the system reliability 9 09 Adv Setup Burn In Press ENT to enter the following screen Burn In Mode Copy amp Compare Use the Up and Down buttons to choose Compare Async Copy amp Cmp and Async Compare then press ENT to confirm Attention ARS 2051F does not have this function 5 10 10 Detect HDD Delay ARS 2051F Only This function is used to set the time interval between the system s re scans of all connected HDD devices Press ENT and the LCD will show the following info 9 01 Adv Setup Detect HDD Delay Press ENT then use the Up and Down buttons to choose different time settings 1 60 sec Detect HDD Delay 1Sec Attention This is Function 9 1 of ARS 2051F 26 SATA HDD Duplicate Controller Manual 5 10 11 Link Option for USB mode requires AEC 4420DX ARS 2051F Only This function is used to decide if 7 USB Mode will be shown in the main menu as pictured below 9 08 Adv Setup Link Option Press ENT and the LCD will display the available options as shown below The default is Menu On and 7 USB Mode will appear in the main menu Link Option Menu On If set to OFF using the Up and Down buttons the 7 USB Mode option will not app
29. with the SATA 2 Connect the target HDDs with the SATA cable to the CN8 blue port on the ARS cable to the black port CN6 on the ARS 2051F 2051F OR 3 SATA HDD Duplicate Controller Manual 3 Connect the power cable to CN4 small 4P 4 Shown below is an ARS 2051F with all the power port on the ARS 2051F equipments properly wired ities e E e ect di 2 4 Install ARS 2055PF The ARS 2055PF is pictured below Before Installation Before connecting the power verify that the local power supply voltage matches the product Prepare 1 Source HDD for the SATA port and 5 Target HDDs The capacity of the target HDDs must be equal or higher than the source HDD The ARS 2055PF support six SATA connections the blue port Source and the black port Target Please refer to the manufacturers instructions for further details Please also make sure that the PSU supplies enough power Installation Procedure 1 Connect the source HDD with the SATA 2 Connect the target HDDs with the SATA cable to the CN5 UP blue port on the ARS cable to the black port on the ARS 2055PF 2055PF SATA HDD Duplicate Controller Manual 3 Connect the power cable to CN8 large 4P 4 Shown below is an ARS 2055PF with all the power port on the ARS 2055PF equipments properly wired 2 5 Install ARS 2061F The ARS 2061F is pictured below Before Installation Before connecting the power verify that the local power supply voltage
30. ze Press ENT to enter the following figure The default is Off Use the Up and Down arrow keys to choose On Copy with Size Off Attention This is Function 5 of ARS 2051F 5 9 USB Mode ARS 2051F only This option allows a copy controller connected to the host computer s USB port to be operated from the PC Choose option 7 from the menu 7 USB Mode Press ENT and the LCD will display the corresponding information as shown below Switch USB Mode NO Use the Down arrow to select YES then press ENT again to switch to USB Mode The LCD will display the following info USB L H Mode D1 HDD D2 HDD Now press ENT to switch to stand alone mode The LCD will display the following info Copy Mode Attention This is Function 7 of ARS 2051F 22 SATA HDD Duplicate Controller Manual 5 10 Adv Setup Adv Setup offers expert users access to more advanced system settings It has 9 sub options Read Error Skip Upadate Firmare Compare Firmware Quick Erase HDD Full Erase HDD H W Diagnostic Load Default Copy HPA and Burn In To access this option hold down the ESC key for two seconds until it appears 9 Adv Setup 5 10 1 Read Error Skip This function sets the system to ignore any errors during the copying process Normally if there is an error during copying a warning is displayed on the LCD By using this function users can also copy a HDD wit
Download Pdf Manuals
Related Search