User`s Manual
Contents
1. me enaliges i 5 Speed is too slow 5 Press Speed to accelerate certain mode 6 The LEDs at each channel are not in series Output current 7 the LED quantity in series less than is beyond the capacity 350mA 700mA 8 the input voltage is lower feclace dcu ablevower than the total voltage of l all the LEDS in series supply 1 Remote battery is low 1 Replace a new battery Pannonisemot 2 Over remote distance 2 Reduce remote distance gt After Sales From the day you purchase our products within 2 years if being used properly in accordance with the instruction and quality problems occur we provide free repair or replacement services except the following cases 1 Any defects caused by wrong operations Any damages caused by inappropriate power supply or abnormal voltage Any damages caused by unauthorized removal maintenance modifying circuit incorrect connections and replacing chips Any damages due to transportation breaking flooded water after the purchase Any damages caused by earthquake fire flood lightning strike etc force majeure of natural disasters Any damages caused by negligence inappropriate storing at high temperature and humidity environment or near harmful chemicals 7 Product has been updated gt Kindly Reminder Power Source Selection Power source must be DC constant voltage type of power supply Due to the efficient output in some power supplies are only 80 of total so please select at least 22. 0 DIP switch is FUN acting as the function key DMX512 Decoder works when FUN is at OFF receiving DMX512 signals Decoder testing mode works when FUN is at position ON as Picture 3 SWITCH1 9 OFF BLACK SWITCH1 IS ON RED 0 SWITCH2 IS ON GREEN t SWITCH IS ON BLUE SWITCH4 IS ON YELLOW 1 SWITCHS IS ON PURPLE SWITCH6 IS ON CYAN SWITCH IS ON WHITE Picture 3 SWITCH8 IS ON 7 CLOLOR JUMPING 8 SPEED LEVELS SWITCHY IS ON 7 COLOR SMOOTH 8 SPEED LEVELS 2 Color jumping amp color smooth speed When decoder is at testing mode DIP Switch 8 is at ON it s the 7 Color Jumping when DIP Switch 9 is at ON it s the 7 Color Smooth with 8 speed levels for each effect SWITCH 1 7 OFF SPEED 0 SWITCH 1 ON SPEED 1 0 PEPE SWITCH 2 ON SPEED 2 SEITCH 3 ON SPEED 3 12345678910 SWITCH 4 ON SPEED 4 SWITCH 5 ON SPEED 5 SWITCH 6 ON SPEED 6 SEITICH7 ON SPEED 7 Picture 4 As Picture 4 When several DIP SWITCH at ON at the same time comply with the largest value switch In Picture4 it shows the decoder status is color smooth at testing function and is at Speed 7 gt Exception Handles Malfunction Causation Solution 1 No power from plu 2 Ea suppl n de UREN EEKE PPly P 2 Check the malfunction No light works re power on 3 Incorrect connection or 3 Check connection cable loose 4 Incorrect RGB output wire 4 Re connect RGB wires Incorrect color connection correspondently
3. 0 higher output power supply than the consumption of LED lights 6 Connect LEDS in series 7 reduce the LED quantity oY pi a ee
4. DMX512 Constant Voltage Decoder User s Manual Decoder is designed via advanced microchip technology to convert the universal standard DMX512 1990 signal into most advanced PWM pulse width modulation digital driving signal it allows user to choose 1 3 output channel 256 level brightness control max 512 output channels This compact decoder connects to light console analog device and various Led terminal products such as RGB Led lamps RGB Led tubes building lamps LED wall washers or lighting and other compatible devices allowing its user to create endless possibilities of light shows Model CONSTANTVOLTAGESA __ _inputsignal SCMX512 1990 __ _ _ _ Dimension L125xW52xH40mm ____ 1 Input standard DMX512 protocol Address can be set by DIP 2 Automatically adapt input voltage DC12V 24V 3 3 output channels 256 scale each RGB driving control 4 10 modes of self Changing 8 level of speed changing 5 Max output 5A each channel Two different versions 3 DMX ADD Version The 1st address controls LEDs on CH1 0 255 steps of brightness The 2nd address controls LEDs on CH2 0 255 steps of brightness The 3rd address controls LEDs on CH3 0 255 steps of brightness 4 DMX ADD Version The 1st address controls LEDs on CH1 0 255 steps of brightness The 2nd address controls LEDs on CH2 0 255 steps of brightness The 3rd address controls LEDs on CH3 0 255 steps of brightness 0 127 of the 4th address controls the brig
5. at the end of each layout of DMX data cable between Foot 2 and Foot 3 Data and Data please also refer to your DMX console manual to select a correct resistor NOTE According to DMX512 protocol in order to ensure a steady data transmission you should add a Operating instructions 1 Decoder address setting This decoder occupies 3 addresses adopted Dip switch to set the address the Dip switches from 1 to 9 area kind of binary value coding switches used to set DMX512 initial address code the correlative bits is the 1 9 bits of the DIP switch the 1 bit is LSC the 9 bit MSC 512 addresses totally DMX512 initial address code is equal to the total amount of the Dip switches number from 1 to 9 press Dip switch downward ON at position 1 user can get the number of its position if pressing upward at position O the number of its position is O Accept DMX512 signal only when the DIP switch FUN OFF at position 0 Example 1 Set to 37 Set the 6 3 1 bit of the DIP switch downward to 1 others to 0 picture 1 the total sum from 1 to 9 is 32 4 1 so the DMX512 initial address code is 37 Picture Example 2 Set DMX512 original address code as 328 Set the 9 7 4 bit of the DIP switch downward to 1 the rest to 0 as picture 2 the total sum from 1 to 9 is 256 64 8 so the DMX512 original address code is 328 VI Instructions for other functions 1 Testing function The 1
6. htness 128 255 for strobing gt Safety warnings Please don t install this controller in lightening intense magnetic and high voltage fields 1 2 3 4 5 To reduce the risk of component damage and fire caused by short circuit make sure correct connection Always be sure to mount this unit in an area that will allow proper ventilation to ensure a fitting temperature Check if the voltage and power adapter suit the controller please select DC12 24V power supply with constant voltage Don t connect cables with power on make sure a correct connection and no short circuit checked with instrument before power on Please don t open controller cover and operate if problems occur The manual is only suitable for this model any update is subject to change without prior notice gt 1 Interfaces DATA _DMX512 IN DMX512 OUT DMX Port DMX512 DECODER DC12V DC24V C FE RoHS Output Port gt 2 Conjunction Diagran 1 Connect to LED strip output to next decoder DMX signal input 7 DC12V 24V WT RG B P EEI E EET 2 Connect to DMX system PC Console DMX512 controller DMX512 console A USB OMK naan Converter i fe 7 iC ji o DMX signal input AZ DM signal input output DC12V 24V input LED Strip LED Strip DC12V 24V BOOOCCCOCOOR goooo0o0oo0oo0o0k LED Strip LEO Stri al eae metalster Metal Thin Film resistor 90 120Q 1 4 W J
Download Pdf Manuals
Related Search