Manual for Eight Channel Triplex DVRs with USB
Contents
1. ON ON ENTER MENU BS IT 3j 16 Network Setup When the cursor moves to Network Setup push the Enter button and the network setup menu window will appear Please note if the Netviewer software is connected to the DVR You cannot access this menu unless you close the Netviewer software 10 8 16 Channel Digital Video Recorder mm AF L L k m IP ADDR 192 166 861 111 GATEWAY 192 168 661 661 2 25 233233888 IP MODE STATIC NETWORK LOCAL H W ENABLE 1 VIDEO PORT 5888 COMMAND PORT 5881 MAC ADDR SET 1 p ba ENTER MENU EXIT IP MODE has 2 IP mode STATIC IP and DHCP if you select STATIC IP you can set the IP address manually if you select DHCP mode the DVR will automatically get the IP address For STATIC IP press upward downward leftward or rightward button to move the cursor among the digits you can press ADD and DEC button to modify the digits also when selecting a digit you can press enter button then press left or right button to select each digit and then press ADD or DEC button to modify this digit press enter to save you change NETWORK the has three types of different network conditions LOCAL LAN EXTER WAN If in local network please select LOCAL If for internet use2. 2 LN lt TN FK C8 Fr b E OMA Gc KW E d Fi _ Fi F P up 24 20 19 18 17 16 15 1 2 25 gt gt T Switch Ch1 Alarm output There are three alarm output pin the status of these pin are illustrated as below After alarm sow There is an example for alarm output connection Before alarm 25 8 16 Channel Digital Video Recorder 4 Hard Disk Connection 1 Open the cover of the hard disk enclosure and unlock 2 Carefully lift the handle on the front of the caddy it using the supplied key When unlocked the key will and remove it from the housing vertical as shown 3 Slide the top cover of the caddy towards the back the end with the connector and remove it 4 Prepare your hard drive by setting the jumper to Master Check the label of the hard drive for information on how to do this 5 Place your hard drive in the caddy and then connect 6 Connect the power connector to the power socket on the data cable to the socket on your hard drive your hard drive The connector fits with the cut off corners at the top 7 Slide the top cover of the caddy towards the end with 8 Replace the caddy into the housing pushing on both the handle to replace it si
3. YS 7 JLL RECORD SET 1 AUDIO CH SET 1 AUDIO SELECT a n 7 ENTER MENU EXIT OVER WRITE if set to YES DVR will automatically overwrite the HDD from the beginning when the HDD is full If set to the will automatically stop recording when the HDD is full If there are two HDD in the DVR when the MASTER HDD is full the video will store to the SLAVE HDD and when the SLAVE HDD is also full the DVR will overwrite the MASTER HDD if set this to yes otherwise it will stop recording REC SPEED the recording frame rate of DVR factory default is 30F SEC under NTSC 25 15 under PAL This means DVR records the events at the speed of 30 shots of frames per second The higher of the record frame rate the more natural look will be displayed on the screen when you playback the footage The lower of the record frame rate the more you can save the space on the hard disk The highest frame rate is 120F SEC PAL is 100 5 when the resolution is in 320 mode REC QUALITY There are four different video quality settings VERY LOW LOW NORMAL HIGH The higher of the video quality the clearer images you can get when you playback The lower of the video quality the more you can save the space on the hard disk drive RESOLUTION the record picture size of the DVR have two modes 360 and 720 default is 360 In 720 mode the recorded
4. 47 APPENDIX PROTOCOL FOR DVR CONTROL 4 2 20 APPENDIX RECORD TIME TABLE eee eene 09 APPENDIX D INTERNET VIEW PLAYBACK CONFIGURATIONS 54 8 16 Channel Digital Video Recorder System Setup Before using the DVR you must first set up the setup the system according to your needs and location otherwise the DVR will run in the default settings which may be unsuitable for you 1 Using the Setup Menu When in setup mode pressing the up or down button will move the cursor will through the various settings continuous pushing will make the cursor move among the options one by one The selected option will be highlighted in yellow While choosing digital fields e g year month day hour minute second etc push the left or right button to move to the different digits of one field Continuous pushing will make it move amoung digits one by one and it can recur Press the or Dec button to change the value that the cursor is highlighting then push the ENTER button to enter sub menu and push the Menu button to return to previous menu 2 Accessing the Menu If the DVR is in the recording mode you can not access the menu unless you stop the recording first Press the Stop button and enter the password to stop all functions then press the Menu button PASSWORD INPUT The password can be a combination of 4 digits
5. 6 CAMB OUT OOOO O00 O OUT 2 4 10 11 12 13 14 15 CAM16 AUDIO ALARM amp RS485 jun LAN Each part of the back panel is illustrated as below 1 video input 1 16 2 main output 3 assistant monitor 4 s video 5 audio input 6 audio output 7 net interface 8 USB port 9 alarm and RS485 port see below 10 debug port 11 12 power Alarm and RS485 port define 1 12 sensor 1 sensor 12 13 20 24 25 GND 14 17 sensor 13 sensor 16 18 RS485A 19 RS485B 21 COM 22 23 23 8 16 Channel Digital Video Recorder 2 Video and Audio Connection The DVR can support up to 16 cameras video input at the same time MAIN OUT ASSISTANT OUT S OUT 75 7 5 Gf C 10 11 12 13 14 15 16 OUT S VIDEO VIDEO IN 1 VIDEO IN 16 de d Microphone There are two steps for camera installation I Connect the Video Signal Line to the DVR channel input II Connect the power adaptor jack to the camera The DVR can connect 4 channel s audio input but you can only select one for recording To display the DVR image the DVR s video output signal should be displayed to your TV set or monitor Any TV set that has a video input terminal is suitable for displaying the image The figure above shows the video and audio signal line connection Note at one t
6. 00 z 01 rom day Sun E to Sun s Virtual Servers List Apply Cancel Help Name Private Protocol Schedule Virtual Server FTP 0 0 0 0 TCP 21 21 always Virtual Server HTTP 192 168 2 33 80 80 always Virtual Server 192 168 2 100 TCP 80 88 always 7 Virtual Server DNS 0 0 0 0 UDP 53 53 always Virtual Server SMTP 192 168 2 89 TCP 25 25 always Virtual Server POP3 0 0 0 0 110 110 always Virtual Server Telnet 0 0 0 0 TCP 23 23 always LAN DVR 192 168 2 167 TCP 5000 5000 always F 192168299 TCP 22 22 always 1921682167 5000 5002 always 55 8 16 Channel Digital Video Recorder Status Firewall Rules can be used to allow or deny traffic from passing through the 01 624 Enabled Disabled LAN DVR Clear Action Allow Deny Interface Range Stat IP Range End Protocol Port Range Source Destination schedule Always From time 01 00 gt AM gt to 01 00 AM Sun to Sun Apply Cancel Help As ADSL and CABLE MODEM network users usually use dynamic IP address so once the restarts the IP addresses will change For this situation users should apply for DNS services To use the Swann DVRs with remote viewing capabilities you may have to ports on your Windows Firewall your Software Firewall or on the Broadband
7. Server ISP ADSL Modem Client Server a A 2 Network Configurations After connecting to Internet DVR users should make the following configurations to make remote view playback 1 When in LAN network administrators should open the following ports for specifics computers 5000 5002 Please make sure that the other services don t use the same ports 2 In case users use ADSL network and the surveillance system computer connect to the ADSL 54 8 16 Channel Digital Video Recorder MODEM then the ports have all opened by default If not please close fire wall by guidance of the ADSL MODEM user s manual 3 In case you connect to Internet by proxy server users should utilize port mapping software and open ports 5000 5001 and 5002 for the surveillance computer 4 In case users connect to Internet by router then users should add the IP address of the surveillance computer and open the above mentioned ports in DMZ setup or Virtual Server setup the names maybe different in various other kinds of routers of the router 5 For CABLE MODEM type and ADSL MODEM type the configurations are similar to the images below Virtual Servet Virtual Server is used to allow Internet users access to LAN semces Enabled C Disabled Mame LAN DVR Clear Private 192 168 2 167 Protocol Type TCP Private Port 5000 Public Port 5001 Schedule G Always time 01
8. 19 Sensor Setup When the cursor moves to Sensor Set then push the Enter button the sensor setup window will appear Press up or down button to move the cursor Press ADD or DEC to change the value 12 8 16 Channel Digital Video Recorder 1 8 x MOTION ENABLE OFF MOTION LEVEL NORMAL MOTION AREA SET 1 BUZZER TIME x a SENSE RECTIME OFF ENTER MENU ALARM ENABLE alarm trigger switch can be set to off low lever or high lever If users set it to off the DVR will ignore the alarm input MOTION ENABLE Motion alarm switch can be set to ON or OFF If set to off the motion alarm MOTION LEVEL motion sensitivity level if the figure in the picture is small please set to high or very high default is normal BUZZER TIME buzzer sound time when there is a sensor or motion alarm SENSE RECTIME when a motion or sensor alarm is triggered the recording time of DVR default is 1 minute If alarm and motion recording if not enabled the value will be set to OFF Note Users should press Schedule button after setting up the parameters so to activate the settings 20 Motion Detection settings 1 When surveying nearby objects 2 10 meters When in daytime please set motion detection sensitivity to Normal level when in night please set to low 2 When surveying objects in 50 100 meters area The objects 50 100 meters away wi
9. 4 5 Stop 5 Stop key in shift mode press this button the DVR will stop record and play If not in shift mode press this button to see big picture of channel 5 While inputting numbers this button is used as number key of 5 6 WM 6 Watermark button In shift mode if the DVR is playing video you can press this button to see the watermark of the picture if the video was recorded by this DVR and has not be changed there will be a watermark symbol in each picture press watermark key again to clear the display If not in shift mode press this button to see big picture of channel 6 While inputting numbers this button is used as number key of 6 7 ADD 7 Add key press this button to see big picture of channel 7 When in system setup menu this is an increase button While inputting numbers this button is used as number key of 77 8 DEC 8 Decrease key press this button to see big picture of channel 8 When in system setup menu this is a decrease button While inputting numbers this button is used as number key of 8 9 Display 9 Display key in shift mode press this button to display current information on the screen press again this to clear the information display If not in shift mode press this button to see big picture of channel 9 While inputting numbers this button is used as number key of 9 10 Schedule 0 Schedule key in shift mode press this button to enter schedule state if
10. Record Time Table 20 Note The above figures are from our test with a 120GB hard disk Just for users reference 22 5 hours Different definition and stabilization objects movement of the images will make some kind of different results 53 8 16 Channel Digital Video Recorder Appendix D internet View Playback Configurations 1 About Networks Users will generally use the following network types and hardware 1 Local Area Network LAN This an internal network usually operated via a hub a switch or a router and will usually operate within an office or household via wireless or Ethernet cable connections 2 DSL or ADSL This is a specific type of broadband Internet access obtained by connecting a DSL or ADSL modem or modem router to a normal telephone cable and setting up an Internet account with an Internet Service Provider ISP such as AT amp T or AOL 3 Port Forwarding This allows external connections to pass through security settings on routers and firewall devices Ports need to be allows in and then directed to the specific IP address of the computer or device that the connection is intending to reach 4 Router This is a device that connects 2 separate networks most commonly a LAN to the Internet and comes with built in security options and allows multiple devices to connect to a LAN and gain Internet access if the router is connected to a modem 7 Client 1 1
11. can not be used at the same time Once the user selects Schedule record mode manual record mode will disabled once user select manual record mode schedule record mode will be disabled 15 8 16 Channel Digital Video Recorder 23 Backup Set When the cursor moves to Backup Set push the Enter button and the backup setup window will appear arD Tay 5 E X _ BACKUPL ENTER MENU i There are two types of backup modes USB and CD RW not included in this model If you select USB backup plug in the USB device and push the Enter button you should see the screen below USB INFOMATION YES 251 OM 26 2M TE SIZE T 2 EM T Hn ENTER MENU 5 gt There two types of backup mode STILL and MOVIE in STILL mode you can backup pictures and in MOVIE mode you can backup video Press ADD or DEC to change the backup mode Please refer to USB Backup for more information For CD RW backup please refer to RW backup 24 Storage Info When the cursor moves to Backup Set push the Enter button and the backup setup window will appear 16 8 16 Channel Digital Video Recorder ENTER MEHU amp gt EXIT 25 Protocol Set You must set the correct protocol so you can control a Pan Tilt camera Speed Dome via the DVR Move the cursor to Protocol Set then push the Enter button and the protocol set window will ap
12. please choose LAN If the internet condition is not very good please select WAN VIDEO PORT the video transmit port for the computer Default is 5000 COMMAND PORT the command transmit port for the computer Default is 5001 If you change any of the VIDEO PORT and COMMAND PORT or MAC address you have to restart the DVR before you use the net viewer software Note if you have change the MAC address you can not see the ADDR SET 17 N W Enable Set When the cursor moves to N W Enable push the Enter button and the N W Enable setup window will appear 11 8 16 Channel Digital Video Recorder ENTER MENU If one channel here set OFF this channel will not transmit to the network so if you want to see a channel from network you must to set this channel ON 18 Mac Set When the cursor moves to Mac Set then push the Enter button the Mac Set window will appear MAC ADDRESS CH EE ENTER MENU If you have more than one 1 a local area network you have to set each DVR to have exclusive MAC address but remember that you have only one chance to modify the MAC address once you have changed the MAC address this menu will not appear again If you want to change the MAC address again please load the factory set then you can change the MAC address For MAC address you d better set the first two bytes to 00 00 and change other bytes
13. CAMBRA IS dente 6 SEIUP o ee 7 12 JAUTOSEO 8 18 RECORD SETUP 8 9 REC Bil O EUER HE 10 INETWORK SETUP 205 a UE 10 IZ NAM ENABLE ri 11 TS MAC SET 12 RE 12 ZO MOTION DETECTION SETTINGS 13 M ig tor a 14 22 SCHEDULE SET C ood OG 15 DR PE oco _ _____ NON 16 24 STORAGE INEO ____________ ME 16 29S ROIOCODSET M MERE 17 1 RECORDING PLAYING CONTROL BUTTONS 18 2 18 Je FUNCTION CONTROLAR ALS etes 20 4 CHANNEL CHOOSING CONTROL AREA 16CH nnn 2 5 CHANNEL CHOOSING CONTBOL AREA GSCH ee De d br 22 SAYS 1 PANEL AND CONNECTION 6 8 23 2 VIDFOANDAU IOGCONNFEMON zeiten ena d UM E M 2
14. Router Modem that you use to connect to the Internet Please consult the documentation or help files on the relevant software or system for instructions on how to do this To successfully access your cameras from the Internet you will need to have allowed access to and from the following ports from an outside connection This process is also called Port Forwarding or creating a Virtual Server connection For more information on Port Forwarding please visit www portforward com Once you have correctly forwarded the ports please check to see what your external IP address 1 this cannot start with 192 168 x x You can check this by going to http www whatismyip com note you must do this on the server machine to find the correct external IP of the router You may also have to place the IP address of the Swann DVR the DMZ of your Firewall to enable the remote viewing interface Information on how to do this should be detailed in the documentation covering operation of your Firewall As ADSL and CABLE MODEM network users usually use a dynamic IP address once the MODEM restarts the IP addresses can change Users can opt for a static IP address which does not change by contacting their ISP Otherwise users can apply for a DNS service through WWW no ip com www dyndns com 56 8 16 Channel Digital Video Recorder Swann Technical Support All Countries E mail tech 9 swann com au Telephone Helpdesk UNITED STATES to
15. are compatible with our DVR I can t turn on DVR A Make sure that the power cord is plugged in correctly and the power light on DVR front panel 18 On Q I see nothing but a blue screen after I turn on DVR A Check the camera input and video output connection on DVR back panel If you can t find problem with these connections check whether the camera power cable is firmly connected Make sure the system format for NTSC and PAL is right Q Can I prevent other people from stopping the recording while I am gone A If the is in schedule or recording mode set password in menu setup no one can change the set unless he has the right password Q How can I erase all data on the hard disk drive A Select HDD Format Set option in the menu Q I forgot my password What should I do A Press the mode button 12 times on the front panel and it will reset the DVR s password to the factory default password of 0000 Q Can my desktop PC read the video data on hard disk drive in DVR A Yes you can use our software to read all video data on hard disk Q What happens if I install my PC hard disk drive into the DVR A You can use a PC hard disk drive in the DVR However once it runs in DVR it will delete any PC operation system and files on the hard disk drive Q What kind of hard disk drive should I purchase to make the DVR run A Any PC compatible IDE ATA hard disk drive will work Q D
16. is used as number key of 77 8 DEC 8 Decrease key press this button to see big picture of channel 8 When in system setup menu this is a decrease button While inputting numbers this button is used as number key of 8 9 SR 9 Single frame backward button in shift mode while in playback state long press this button can see single frame backward press play button to play normally If not in shift mode 19 8 16 Channel Digital Video Recorder press this button to see big picture of channel 9 While inputting numbers this button is used as number key of 9 10 SF 0 10 Single frame forward button in shift mode while in playback state long press this button can see single frame forward press play button to play normally If not in shift mode press this button to see big picture of channel 10 While inputting numbers this button is used as number key of 0 11 WM 10 Watermark button In shift mode if the is playing video you can press this button to see the watermark of the picture if the video was recorded by this DVR and has not be changed there will be a watermark symbol in each picture press watermark key again to clear the display If not in shift mode press this button and then press 1 to 6 to see big picture of channel 11 to channel 16 12 Menu search press this key to enter search menu long press this key to enter menu need password if 1n menu setup press this key to qu
17. of 0 9 The default 15 0000 To enter the menu you must input the correct password by pushing the digit buttons If the password you have inputted is incorrect the system will automatically return to the main screen If you want to cancel the input of the password you can push the Menu button to return to the main screen again While inputting the password in order to avoid being revealed to bystanders the password you input is displayed on the screen as signs To change the password please refer to the password change section 8 16 Channel Digital Video Recorder 3 System Setup When the cursor moves to System Setup please push the enter button and the System Setup window will appear which is illustrated as below _ TC kha 4 E i DISPLAY RECORD HETWORK SENSOR SCHEDULE BACKUP STORAGE INFO PROTOCOL SET ENTER MENU t gt 4 FORMAT ISET 141 FACTORY RESET 491 SE T HEHU LANGUAGE ENGLISH UIDEO SISTEM FAL BUZZER SOUND ON CHANGE PASSWORD 4 FIRMWARE UPDATE 1 ENTER MENU gt EXIT MENU LANGUAGE language set of the push Dec to change language VIDEO SOURCE switch the video format to suit the TV standard of your country NTSC or PAL BUZZER SOUND buzzer switcher if set to OFF the buzzer will not work If moti
18. of recording if the hard disk is full and the system is set to automatic overwrite the recording will not be interrupted but the DVR will automatically begin to overwrite recorded video from the earliest oldest recorded area If the system is set to overwrite disabled it will stop recording once the HDD is full 4 Alarm Recording Alarm recording is not started by manually pushing the Record button it is automatically activated once Schedule mode is enabled Alarm recording can be activated by alarm input signal or motion if the connection of alarm input equipment is correct stable and reliable and the alarm settings are correct For recording to be activated by exterior input signal or motion detection the system must be set to 2T 8 16 Channel Digital Video Recorder Schedule Mode active and that period is set to in Record Schedule setup You must also set the menu of Alarm Setup for exterior input alarm and the alarm enable setting of that channel must be set to For Motion Alarm the motion enable setting of that channel must set and set the area for motion detection must be set If Schedule mode is disabled the system will not start recording on alarm Setting schedule on off is achieved through pushing the SCHEDULE button on the front panel or remote but not through the System Setup menu and window When the unit is in Schedule Mode active the character 5 will display on the screen
19. the folder Plug the USB device into the DVR go to the menu of Backup set check that whether the USB device was detected go to the Firmware Update menu and select USB method move to Update Start and press Enter button and the update will start If you see screen below update was successful Then reboot the DVR NOTE do not shut down the DVR when the DVR is updating this may cause fatal problem ENTER MEHU EXIT 14 Zoom Operation In shift mode press zoom button the DVR will be in zoom mode which is illustrated as below Press upward downward leftward or rightward to move the zoom area then press enter button to zoom press zoom button again to cancel zoom operation 35 8 16 Channel Digital Video Recorder 2885487722 18 42 16 12 CH83 CHB4 CH85 CHES CH11 CH13 14 CH15 CH18 SHIFT 15 Information Display In shift mode press display button the main information of the DVR will display on screen HDD HDD HDD HDD 2885 87 22 FRI 18 43 82 MODEL SIZE USED READ DUERURI TE LIST EVENT LIST REC DUER EVENT HETUORK IP S W UER MASTER HDD SIZE the size of the hard disk tor 886 BB 5 8 B888 HO DETECT 8888 8818 192 168 884 258 7627665672114 HDD USED the used space of the hard disk HDD READ current HDD address for
20. time 1s not set to off and the 15 in schedule mode Otherwise set the motion level to HIGH or VERY HIGH Q When the network connection between DVR and client computer is cut off why the DVR halts and clock stops In case network is cut off abnormally DVR machine will halts for 20 seconds without response to any operation of pressing front panel buttons 20 seconds later it will restore normal state but the icon that shows network status won t disppear in 10 minutes and in this period client computer cannot connect to the DVR or enter network menu Q I press the menu button but it do not display the password menu to enter menu why For 16 ch user to enter menu you have to long press the Menu search button if you just press this button you will see the search menu Q I long press the Menu search button but it do not display password menu and directly enter the menu why do not I need a password A If the password level setup in Password Setup is USE you do not need a password to enter the menu if you want to need a password when enter menu setup just change the password level to SETUP 48 8 16 Channel Digital Video Recorder Q How much HDD size dose this DVR support A Any type size of the HDD is OK to the DVR but if the size is much more then 300G it may display only 300G on the DVR and it does not effect the real size use on the DVR 49 8 16 Channel Digital Video Recorder App
21. 4 PAFARMO ONEC ON andans a ar 25 AHARD DISK CONNEC 26 8 16 Channel Digital Video Recorder QUICK USER GUIDELINE rie re eer ena Bo REIT acciones sche esa acta oa tate eae 8 27 ZAIURNODQBEEZTZHEDWVB scc MEE UE M UE 27 a NORMAL RECORDING dise eiu EM LI DM MEET 21 27 SLIME edicit D 27 ramas ama nme 26 utt CU Mf M UC 28 SEARCH dn ee 30 ____ ______ _ De 31 POSS TARTS TOP 32 32 Mi Te OP m UU T 33 1 25 35 IA ZOOM OPBRJATION usc RU E EE 35 t To I AGREE Re ue PERRO ORAE X 36 OPTA 34 38 IS REMOTE CONTROL cdam MEE 40 VIEWSOFIWAR xat uentus uu cb 41 APPENDIX TROUBLE SHOOTING 2
22. Alarm video recording can t be stopped by pushing the RECORD or STOP button while Schedule Mode is active To ensure that once Schedule Mode is set to on that the schedule cannot be accidentally stopped there is a password protection to stop Schedule Mode You must press the SCHEDULE button then enter the correct password to turn Schedule Mode off Check Alarm Recording setup before recording confirm the video quality and the frame rate as the record setting can t be changed during the recording process As long as the alarm input signal is correctly set the alarm recording will continue during the period of time set up by A M REC TIME and when the outside the time period the alarm recording automatically stops 5 Time Recording Time recording starts and stops recording automatically according to the pre arranged time period It is applied to a fixed timetable for example business hours time recording or outside business hours time recording with fixed start stop time To start the Time Recording function you must have a record schedule setup beforehand When this is done push the SCHEDULE button on the front panel to set schedule mode to on and the schedule symbol S will display on the screen The Time Recording mode will not work unless you activate Schedule Mode To make Time Recording mode active the system must be set to Schedule Mode active and that period is set to in Record Schedule setup In Time Record mode you must p
23. Backup Plug in the USB device go to the menu of Backup set check whether the USB device was detected and there is enough free space of the USB device select the backup mode then completely exit the menu system USB backup is available only in playback mode If you selected STILL for the backup mode press the USB button and an 5 will appear on the screen When it disappears the backup of the picture 15 finished and you can un plug the USB device out and see the picture on a computer with the net viewer software If you select MOVIE for the backup mode press and hold the USB button until the A appears on the screen press the USB button again to select the end of the backup video This may take a little time and make sure the USB device has enough free space if the disappears the backup is ok and you can view the video on a computer with net viewer software NOTE if you backup still picture please choose full picture display We recommend using high quality USB thumb drives like Sandisk or Legend Australia only with the DVR For long duration backups we recommend saving the footage to VHS tape using a VCR 12 CD RW Backup This function is only selectable if your DVR came with a CDRW If you enter CD RW backup menu you will see the screen below START TIME SETEI I START 2885 11 84 84 31 END 2665411863 15 37 BACKUP SIZE 658MB BACKUP 21 ENTER MENU Start Time Set you
24. OQ Swann 8 16 Camera Digital Video Recorder For Network amp Web Monitoring with USB backup Manual Ver 1 0 8 16 Channel Digital Video Recorder Security Notice e Power supply This Digital Video Recorder uses DC 12 voltage indoor power supply The voltage of the power must be verified before using When the DVR is not in use for a long time pull out the plug from the socket and disconnect the power e Security This DVR is for indoor use only in order to avoid the danger of a short circuit or electric shock please do not expose the DVR to rain or a moist environment If any solid or liquid enters the unit s case please turn off the power supply immediately and ask for qualified technician to check the DVR before restart the unit This DVR 15 precise instrument do not attempt to repair any component of the DVR by yourself as this will void your warranty If your DVR malfunctions in any way please contact a dealer in your area or Swann Technical Support directly e Installation Please choose appropriate site to install the DVR to ensure well adequate ventilation around the DVR to avoid excessive heat Do not install the DVR near a radiator ventilating trunk heat sources under direct sunshine dusty location or anywhere there is a chance of mechanical librations or impact Features of this DVR e Video input 8 16channels input video output output e Audio input 4channels input audio output output e Four op
25. When the cursor moves to Change Password please push the enter button and the Password window will appear 855 SETUP SYSTEM RECORD SCHEDULE ENTER MENU i te o m n Password Level password type of the DVR the DVR has various types of password SETUP If set to YES you have to input password to enter menu SYSTEM If set to YES you have to input password to boot DVR RECORD If set to YES you have to input password to stop manual recording SCHEDULE If set to YES you have to input password to cancel schedule recording 8 16 Channel Digital Video Recorder If you select the Password Change and push the Enter button the Password change window will display as below An RD CHARI SETUP SYSTEM RECORD SCHEDULE ES PASSWORD lo ENTER MENU t 4 I 4 Please enter the current password then input new password and confirm the password 8 Firmware Update When the cursor moves to Firmware update please press enter button and the update window will appear WUO D UPDATE METHOD USB UPDATE STARTI RF Ei ENTER MENU EXIT Update Method There are two methods to update the DVR firmware USB for USB thumb drives and Network not support USB update create a new folder nam
26. an be operated by the remote device 40 8 16 Channel Digital Video Recorder 19 PC View Software Operation Use the PC View software you can view the DVR through Internet also you can view and backup the video information on the HDD through a computer Open the software you will see the window below m Wicwcr En 71 BS 20 04 Carn Mo 05 Cam 4o 06 17 B VIEWER 00 10 11 NETWORK 13 14 15 CzmHo 8 Field p settings Shard NETWORK za Kee Stop EFE Live PlayDack Fast Epeecd Qui Quer Lex Please click Setting button you will see the window below Hetwork Setting Hetwork Video IF Adar Video Size Fullzi s Halfsi AV Port 5000 Video v NTSC rere Command Fort 5001 Frame Sec 15 z Commor AVI Codec Cinepak Codec by Radius Enable Channel Transfer Intel Indeo R Video 2 Intel Indeo Video 2 Intel Indeo Video 4 5 Max Channel 16 CH Intel codec Microsoft Video 1 Ligos Indeo Video 5 2 Microsoft Windows Media Vid Local ree V hicrossft MPEG 4 Video Code a i MEN Wa ann Enter the IP address and cli
27. as number key of 2 3 PIP 3 USB key in shift mode press this button the will start USB backup please refer to USB backup operation in user guideline for details If not in shift mode press this button to see big picture of channel 3 While inputting numbers this button is used as number key of 3 4 Display 4 Display key in shift mode press this button to display current information on the screen press again this to clear the information display If not in shift mode press this button to see big picture of channel 4 While inputting numbers this button is used as number key of 747 5 Freeze 5 Freeze key in shift mode press this button the DVR will be in freeze mode please refer to freeze operation in user guideline for details re press this button to quit freeze mode If not in shift mode press this button to see big picture of channel 5 While inputting numbers this button is used as number key of 5 6 Schedule 6 schedule key in shift mode press this button to enter schedule state if the DVR is in schedule state there will be a 5 symbol on screen press again this button to quit schedule mode If not in shift mode press this button to see big picture of channel 6 While inputting numbers this button is used as number key of 6 7 ADD 7 Add key press this button to see big picture of channel 7 When in system setup menu this is an increase button While inputting numbers this button
28. aying 7 Search Play Push the search button to display the Search play window on the screen 28085787722 FRI 11 85 18 EVENT SEARCH START STOP SEARCH 1 ENTER MENU EXIT TIME SEARCH search recording to the time entered EVENT SEARCH search recording by event list START STOP SEARCH search recording by segment Press the up or down buttons to move cursor then press Enter button to enter sub menu you have highlighted Push the Search button again to quit from search menu 29 8 16 Channel Digital Video Recorder 8 Time Search Move the cursor to Time Search then push the Enter button and the Time search window will appear as illustrated as below 2885 87 22 FRI 11 85 33 The red block below the number means there 15 recorded video at that time Push the left and right buttons to move the cursor along the year month day hour and minutes Push the ADD and DEC buttons to modify the date and time Please note You can only view footage that has been recorded Therefore you must select time and dates that have a red block below them 30 8 16 Channel Digital Video Recorder 9 Event Search Move the cursor to Event Search and then push the Enter button the event search window will appear which is illustrated as below There are four types of event on this list MOTION ALARM SCHEDULE and NETWORK MOTION means motion triggered alarm recording ALARM means external sensor triggered alar
29. aying Playing and stop will work simultaneously on 16 channels This button doesn t work during Time recording and Alarming recording 3 Rew Fast rewind button Push this button to start fast rewind playing Push the play button again to start playback at normal speed 4 Forward Fast forward button Push this button to start fast forward playing Push the play button again to start playback at normal speed The fast forward has five speeds every time you push the button the play speed will increase from slow to fast and then back to slow 5 MODE Mode change key press this key to switch to shift mode re press to change to normal mode 2 Function Control Area 16 ch 18 8 16 Channel Digital Video Recorder search O A 1 Auto 1 Auto key in shift mode press this button The will be in auto dwell state it dwells according to the time set in auto sequence set menu you can set the dwell time of each channel Press this button to quit this mode If not in shift mode press this button to see big picture of channel 1 While inputting numbers this button is used as number key of 1 2 Zoom 2 Zoom key in shift mode press this button the DVR will be in zoom mode please refer to zoom operation in user guideline for details press zoom button again to cancel zoom operation If not in shift mode press this button to see big picture of channel 2 While inputting numbers this button is used
30. can set the backup start time START backup start time END backup end time Backup Start start backing up with CD_RW If you select Start Time Set and press enter button the Backup Start Search window will appear which is illustrated as below The operation is the same with time search please select the start time you want to backup 33 8 16 Channel Digital Video Recorder 2885711788 ENTER Exit If you have selected the start backup time then you have to change the backup size here you can change the backup size you want from 1M to 650M After these steps you can insert your blank CD into the CDROM and select Backup Start you can see the screen below Ly START TIME SETI I START 2005 11 04 84 31 END gt 2885211103 15 37 SIZE 2 658MB START 4 TA BACKUP START ENTER MENU gt If backup finish you can use the net viewer soft s DriveScan function to see the video on If the cd has been writed press usb button to format the cd 34 8 16 Channel Digital Video Recorder START TIME SETC I START 2085 11 88 16 36 END 2085 11 88 16 36 BACKUP SIZE 658MB BRCKUP STRRTI J Er WAIT ENTER MENU gt EXIT 1 13 USB Update Using your PC create a folder called firmware in the root directory of your USB thumb drive copy the update files to
31. ck button 4 8 16 Channel Digital Video Recorder Click connect button enter password the password is the same as the DVR password Logon Sys tem 192 188 1 10 Password O Cancel then click the OK button if connect to the DVR you can see the picture below Click the Confirm button Het iewer Eg AN Connect When users survey bv Internet thev should firstly open ports 5000 5002 default and can be changed on the DVR on the router side Please learn more about how to do from the manual of router Live PlayBack ScanDisk FilePlay 1 Play if you select this you will start to play the video on DVR Stop if you select this you can stop the play AVI if you select this you can save the picture to AVI format on you computer LOCAL you can save the video in you computer and open with this software Live you can select this button to see live picture just click the play button Playback you can view the playback video in the DVR 42 8 16 Channel Digital Video Recorder 7 ScanDisk if you select this you can view the video on the HDD or CD which recorded in the DVR and then connect to the computer 8 File Play you can play the video file on the computer AVI Save when play video click AVI button the video will save as AVI format on the computer you can play the file with any media player s
32. des to ensure a solid connection then turn the key to the horizontal position to lock it Please note For instructions on how to jumper your hard disk drive HDD to master please refer to the information found on the label on top of the hard drive or visit the hard disk drive manufacturers website Also note that the key must be in the locked position for the hard disk drive to work If the key is left in the unlocked position the power to the hard drive 15 switched off Note If the DVR comes with a CD RW please fellow the below steps Open the DVR cover fix the HDD to the DVR HDD shelf of soleplate then connect the power and digit cable If you have another HDD please jump the first one to MASTER and the other to SLAVE put that HDD on the other HDD shelf and then connect the power and digit cable 26 8 16 Channel Digital Video Recorder Quick User Guideline 1 Start the DVR Before starting the DVR please make sure all the items in the Security Notice at the beginning of this manual are fulfilled and that the input and output cables are all correctly connected Also ensure the DVR s video input format NTSC PAL and the monitor NTSC PAL are both set to the same video standard NTSC for USA amp Canada PAL for Australia UK and most of Europe Fit the hard disk to the removable caddy and insert the removable caddy into the housing then lock it up turn the hard disk lock to the right and connect the power which
33. ed firmware in the USB thumb drive s root directory copy the update file to the folder plug in the USB thumb drive Enter the Firmware Update menu select Update Start and press enter button the system will start updating When updating 15 finished the window below will be displayed please manually reboot the DVR 8 16 Channel Digital Video Recorder ENTER MEHU EXIT 9 Display Setup When the cursor moves to Display Setup please push the Enter button the Display Setup window will appear COLOR SET AUTOSEG SET BDUHD COLOR BLACK BLANK COLOR BLACK MP HR i 34 ENTER MENU EXIT 10 When the cursor moves to Camera Name please push the Enter button the Camera Setup window will appear 8 16 Channel Digital Video Recorder ENTER MENU Press the up or down button to select channels press the Enter button to change the channel 3E Jr CH82 CHEZ CHES CHES CHES CHES CHEE CHEE a CHB CHE 2 EH81 n A 4 7812345678 g OD4RBEDEFGHI JKLMHOPG 2 21 _ k imnopgqrstuvuxyz ENTER MENU gt Each channel s name is the combination of eight characters Press left or right button to select each character press ADD or DEC button to modify each character a
34. endix B protocol for dvr control Serial port setting BAUD n 8 1 BAUD RATE 1200 2400 4800 9600 19200 PTCI three byte m oo Ox2F 0x5a Ox4d MIN ____ __ __ OF 50 8 16 Channel Digital Video Recorder PTC2 seven byte Transmitting S N Transmitting worth Instructions 5 7 Refer to 1 Same command as 1 PTC3 seven byte Ad var Checksum Byte 5 and byte 6 are ransom value from 0x00 to Oxff Byte 7 mod byte2 byte3 byte4 byte5 byte6 100 Note This protocol is the same as PELCO D which is used to control speed dome So if you use PELCO D to control speed dome by a keyboard you can also use the keyboard to control the DVR through this protocol we can use different address to distinguish the DVR and the speed dome 4 eight byte bytel xor byte2 xor byte3 xor byte4 xor byte5 xor byte6 xor byte7 51 8 16 Channel Digital Video Recorder A De _ Forward Frame owad Note This protocol is same as PELCO P s call function you can use PELCO P s call function to control the DVR First you must set right protocol baud rate and address second you press call button on the keypad then press the number according to Var above last press enter button 52 8 16 Channel Digital Video Recorder Appendix
35. ibility of the end user This warranty applies to the original purchaser of the product only and 18 not transferrable to any third party Unauthorised end user or third part modifications to any component or evidence of misuse or abuse of the device will render all warranties void FCC Notice We Swann Communications of 10612 Shoemaker Avenue Bldg B Santa Fe Springs CA 90670 USA declare under our sole responsibility that the product To which this declaration relates Complies with Part 15 of the Rules Operation 15 subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 57
36. ime you can only connect one audio input which means if you connect an audio to caml you cannot connect anyone else from cam2 to cam 4 24 8 16 Channel Digital Video Recorder 3 Alarm Connection The DVR can support 16 alarm input and 3 alarm output Alarm input There are two types of alarm input 1 Voltage output 5V and OV A In case sensor output high voltage 5V normally and output low voltage when triggered then users must set as low voltage alarm B In case sensor output low voltage 0V normally and output high voltage when triggered 5V then users must set DVR as high voltage alarm Please refer to the picture below channel 2 to channel 16 are the same as channel 1 42 0 x 8 F 8 7 56 p 5 3 2 FR 1 1 1 1 ME LA M gt ae a E F C F gt sensor Ch1 2 Open Close output A N O Normal open close when triggered DVR must set as low voltage alarm B N C Normal close open when triggered DVR must set as high voltage alarm Please refer to the picture below channel 2 to channel 16 are the same as channel 1 48251241 240 2 9 kond M AE T on o os dd Lat 1 E yg x Pil n i i i i i j F 1 1 1 a A a MR 1
37. ing video press this button to pause the play press play button to continue play 5 Channel Choosing Control Area Sch 1 Big picture add up Press this button to see full screen re press this button to see the next channel While selecting menu items press this button to move up the cursor 2 Big picture dec down Press this button to see full screen re press this button to see the preview channel While selecting menu items press this button to move down the cursor 3 Four pictures left Press this button to see four pictures display re press this button to see next four pictures While selecting menu items press this button to move the cursor leftward 4 Fight pictures right Press this button to see eight pictures display While selecting menu items press this button to move the cursor rightward 5 Enter While selecting menu items press this button to select the item While playing video press this button to pause the play press play button to continue play 22 8 16 Channel Digital Video Recorder System Connection 1 Back Panel and Connection Terminals The power cable and input output signal terminals are all at the back of the machine the connections to monitor camera etc equipments are all carried out through the terminals and sockets on the back panel The back view of the machine is illustrated as below Take 16 ch for example 8 ch is much the same as 16 ch AM1 2 CAM3 CAM5
38. it current menu 3 Function Control Area 8 ch 1 Auto 1 Auto key in shift mode press this button The DVR will be in auto dwell state it dwells according to the time set in auto sequence set menu you can set the dwell time of each channel Press this button again to quit this mode If not in shift mode press this button to see big picture of channel 1 While inputting numbers this button is used as number key of 1 2 Zoom 2 Zoom key in shift mode press this button the DVR will be in zoom mode please refer to zoom operation in user guideline for details press zoom button again to cancel zoom operation If not in shift mode press this button to see big picture of channel 2 While inputting numbers this button is used as number key of 2 3 USB 3 USB key in shift mode press this button the DVR will start USB backup please refer to USB backup operation in user guideline for details If not in shift mode press this button to see big picture of channel 3 While inputting numbers this button is used as number key of 3 4 Freeze 4 Freeze key in shift mode press this button the DVR will be in freeze mode please refer to freeze operation in user guideline for details re press this button to quit freeze mode If 20 8 16 Channel Digital Video Recorder not in shift mode press this button to see big picture of channel 4 While inputting numbers this button is used as number key of
39. ll be quite small on the screen When in daytime please set motion detection sensitivity to high level 13 8 16 Channel Digital Video Recorder 2005101106 09 14 47 2005 01 06 18 37 20 Note the above suggestions are guide only based on testing in a general environment You will need to select the best parameters according to the actual operation environment you are covering Try different settings until you get the desired motion detection result 21 Area Set Move the cursor to Alarm Set then push the Enter button and the alarm setup window will appear Push the up down left right button to move the cursor and press the Enter button to change from detection ON to OFF Push and hold the Enter button to change all values to the same as the area you have selection 14 8 16 Channel Digital Video Recorder If the area marker icon is set to yellow this area is monitored for motion detection and if the icon is grey motion sensing is disabled for that area 22 Schedule Set When the cursor moves to Schedule Set push the Enter button and the schedule setup window will appear ENTER MENU You can change recording schedule during a week by using this setup windows Please note Military time must be used START start record time STOP stop record time Note Manual record mode and schedule record mode including motion detection record mode sensor record mode and time schedule record mode
40. ll free 877 274 3695 Sun Thurs 2pm 10 30pm PST USA Exchange amp Returns 562 777 2551 Mon Fri 9am 4pm PST AUSTRALIA toll free 1300 13 8324 Mon Fri 9am 5 30pm Aus EST International 61 3 8412 4610 Mon Fri 9am 5 30pm Aus EST See http www worldtimeserver com for information on different time zones and the time in Melbourne Australia compared to your local time WARRANTY INFORMATION Swann Communications warrants this product against defects in workmanship and material for a period of one 1 year from it s original purchase date You must present your receipt as proof of date of purchase for warranty validation Any unit which proves defective during the stated period will be repaired without charge for parts or labour or replaced at the sole discretion of Swann The repair or replacement will be warranted for either ninety days or the remainder of the original one year warranty period whichever is longer The end user 15 responsible for all freight charges incurred to send the product to Swann s repair centres The end user is responsible for all shipping costs incurred when shipping from and to any country other than the country of origin The warranty does not cover any incidental accidental or consequential damages arising from the use of or the inability to use this product Any costs associated with the fitting or removal of this product by a tradesman or other person or any other costs associated with its use are the respons
41. m recording SCHEDULE means scheduled time recording NETWORK means network activated recording Press the up or down buttons to move the cursor along the event list push the left or right buttons to see previous or next page and push the Enter button to play the segment you selected Push the search button to return to the Search Play menu 2885 87 22 FRI 11 16 38 8 7 6857877805 EHTER If you want to change the between the MASTER HDD and SLAVE HDD push the mode button then press Enter button Push the Menu button to exit 31 8 16 Channel Digital Video Recorder 10 Start Stop Search Move the cursor to the Start Stop Search push the Enter button and the Start stop search window will appear recorded segments are displayed here push the up or down buttons to move the cursor along the segment list press left or right buttons to see previous or next page push the Enter button to play the segment you selected Press search button again to return to the Search Play menu 87722 FRI 11 17 12 E Ji 8578 8578 7711 8578 7711 8578 7711 685787705 85787785 85787785 If you want to change the between the MASTER HDD and SLAVE HDD push the mode button then press Enter button Push the Menu button to exit 32 8 16 Channel Digital Video Recorder 11 USB
42. nd then press enter button to save this name DISPLAY if Display is set to OFF the channel s name will not display on the screen 11 Color Setup When the cursor moves to Color Set please push the Enter button the Color Setup window will appear CON picture contrast BRI picture brightness HUE picture hue SAT picture saturation 8 16 Channel Digital Video Recorder um ENTER MENU 5 gt EZIT Press left or right button to select CON BRI HUE SAT press ADD or DEC to change the value if setup over press ADD or DEC to change channel 12 Autoseq Setup When the cursor moves to Autoseq Set please press enter button the Auto Sequence Setup window will appear ENTER MENU gt Press the up down button to select channel press ADD or DEC button to change the auto Sequence time 13 Record Setup When the cursor moves to Record Setup then push the Enter button the Record Setup window will appear which 1s illustrated as below Press up or down button to move the cursor Then push the ADD or DEC button to change the value While the DVR is in recording or playback mode 8 8 16 Channel Digital Video Recorder you cannot access this menu unless you stop record or play first UE GETI 1195 0 P EM OVER WRITE REC SPEED SBF SEC REC QUALITY HIGH RESOLUTION DEC Ee S r xd
43. oes this DVR kit come with sensors cameras or hard disk drive A No You have to buy each accessory separately 47 8 16 Channel Digital Video Recorder Q What is the capacity to record A Up to a year with two 120 GB HDD at the lowest quality when set at frame per second Q Does this DVR come with a remote control either hardwire or wireless Yes there 15 a remote control come with the Q Why cannot I access Time Date Set HDD Format Set Record Set menu A Please stop record or play before you access these menu Q Why cannot I access Network Set menu A Please stop the connection of the PC View soft from Internet before you access Network Set menu Q I press record button but the DVR does not start recording why A Press display button to see 11 there 15 a hard disk detected also if the is in schedule mode there 15 a 5 on the screen in yellow you cannot start recording by press record button you have to press schedule button again to cancel schedule mode Q I press record button while recording but the DVR does not stop recording why A If the is recording in schedule mode there is a 5 on screen you cannot stop recording unless you quit schedule mode first Press schedule button to cancel schedule mode Q There is a movement but the DVR does not start recording A Make sure the motion enable of that channel 1s on the area set 1s ok the A M rec
44. oftware is in File Play mode click File Play file play window will display it can play the video on HDD of you computer Live PlayBack ScanDisk FilePlay Speed 0 20 From To Current Click Open select one video file the click play it will play the video file Main standard amp parameter chart 44 8 16 Channel Digital Video Recorder Work Temperature 41 F 122 F 5 C 50 C humidity lt 90 Store Temperature 4 F 158 F 20 C t70 humidity lt 9590 PX IT x 16 67 x 430x 400mm H x W x D Environment temperature 45 8 16 Channel Digital Video Recorder Exterior size 430mm romm gt POWER REC PLAY REWFORWARD MODE 400mm o Incase list Incase list Name Quantity Digital Video Recorder 1 Remote Control BNC Adaptors in bag Power Supply Netviewer software CD User Manual 8 16 Channel Digital Video Recorder Appendix A Trouble shooting guide Q What kind of camera should I buy for this DVR A Any BNC or RCA interface indoor outdoor infrared camera will work with the DVR It doesn t matter whether it s a color or black white camera However web cameras that require a USB interface are not compatible with the DVR Q What kind of alarm device should I buy for DVR A Most sound alarms
45. on detection 1s enabled the buzzer will sound when motion is detected 4 Time Date Set When the cursor moves to TIME DATA SET push the Enter button and the Time date set window will appear as illustrated as below 8 16 Channel Digital Video Recorder 288578 7 722 18 21 21 FORMAT T T Y Y MM DD LOCAL ENTER MENU Please push up down left and right buttons to move the cursor press ADD and DEC button to modify the value FORMAT the date display format which can be different for USA EURO and Australian users DISPLAY if set to OFF the time will not display no the screen LOCAL time display position on the screen 5 HDD Format Set When the cursor moves to HDD FORMAT SET please push the Enter button and the HDD Format Setup window will appear which is illustrated below If you select Y ES and press the enter button all video files on the HDD will deleted If you do not want to delete all recording please select 8 16 Channel Digital Video Recorder 6 Factory Reset When the cursor moves to System Setup push the enter button and the Factory Setup window will appear ENTER MENU EXIT 2 If you select YES and push the enter button all the DVR settings will reset to default if you do not want to reset to default settings please select 7 Change Password
46. pear Push the up or down button to move the cursor and press ADD or to change the value CHE 4 BRUD RATE DOME ADDR PROTOLOL SEE DURPROTOCOL DURADDRESS DURBAUDRATE ENTER MENU gt CHANNEL SEL If you have a speed dome camera select the channel which the camera is connected to BAUDRATE Changeable from 1200bps to 19200bps The default value is 2400bps DOME ADDR The address of the speed dome camera changeable from 0x00 to Oxff PROTOCOL The protocol of speed dome camera pelco p pelco d neon or lilin DVRPROTOCOL The protocol used by the computer or keyboard to control the DVR please refer to appendix A DVRADDRESS The address of the DVR for DVRPROTOCOL can be changed from 0x00 to Oxff DVRBAUDRATE The baud rate of DVR for DVRPROTOCOL 17 8 16 Channel Digital Video Recorder Buttons On the Front Panel The front view of the video recorder is illustrated as below 0090 PLAY REW FORWARD MODE 6 1 Record This is the manual recording button Push this button to record Re push this button or push the stop button to stop recording enter your password to confirm Recording and stop will work simultaneously on all 16 channels This button doesn t work in schedule mode 2 Play Push this button to start playing the video stored in hard disk Re push this button or push the stop button to stop pl
47. picture is twice the size of that in 360 mode In 360 mode the REC speed is 120F SEC NTSC PAL is 100F SEC and the maximal REC speed in 720 mode is 60F SEC NSTC PAL is 50F SEC PB SPEED the frame rate of playback default is NO USE which means the same as record 14 Audio ch Setup When the cursor moves to Audio CH Set push the Enter button the Audio CH Setup window will appear as illustrated below There are four audio input channels for each channel you can select anyone of the 16 channels Although there are four audio input channels you can only record from one channel s audio at the same time To setting the audio correctly you have to select one channel within these four channels in the Record Setup menu 8 16 Channel Digital Video Recorder ru AUDIO2 AUDIOS AUDIO4 ENTER MEHU gt EBX IT 15 REC ch Setup When the cursor moves to REC ch Set please press enter button the REC ch setup window will appear This screen 15 different for 720 size and 360 size In 720 size the window is illustrated as below press upward and downward buttons to select channel and press ADD or DEC button to change the setting If the channel is set OFF this channel will not record when in recording mode If the resolution is set to 360 size the REC ch Setup window can not be setup cro NCC s hi gt c CH81 CH82 ON 4 CH85 ON
48. playback OVERWRITE overwrite time of the HDD NETWORK IP IP address of the DVR REC LIST number of record list EVENT LIST number of event list REC OVER record list overwrite or not 36 8 16 Channel Digital Video Recorder EVENT OVER event list overwrite or not S W VER software version 16 PTZ Operation This DVR can control all speed domes which are connected to the DVR To control the speed dome make sure all the lines are correctly connected first you must set the right protocol baud rate and speed dome s address for each speed dome please refer to protocol set For example you connect the first speed dome to channel one you should make sure that the baud rate the protocol and speed dome s address is the same as the speed dome you connect to the channel PTZ can only be operated by remote device press the PTZ button on the remote device PTZ will be display on the screen then select 1 to 16 to choose PTZ channel the channel number will be displayed after PTZ please refer to the picture below 2885 87 22 FRI 11 32 83 You can press up down left or right buttons to move speed dome and press Enter button to stop If you press the Iris button the character Iris will appear on the screen please refer to the picture below then you can press the ADD and DEC button to change the iris the same to control the focus zoom and speed also press ente
49. r button to stop 2T 8 16 Channel Digital Video Recorder 2885 87 22 FRI 11 33 31 PTZ 5 IRIS Press the PTZ button one more time to exit from PTZ control 17 Default Setting Default setting for each item is shown in the below chart Defaults 18 the initial setup by the manufacturer User can change the setup according to the actual environment and demands If there is any confusion or unexpected effect choose Defaults and readjust You can choose RESET in SYSTEM SET menu and reset all settings to default setting Year Month Day 2005 01 01 2000 2099 Common sense Hour Minute 12 00 00 rules General setting Play Repeat YES NO Video Input NTSC format NTSC PAL Very Overwrite Enable YES NO 60f s NTSC 120f s 1f 2s NTSC Rec Speed SOf s PAL 100f s 1f 2s PAL 3e _ Recording Para 120f s no use NTSC PB Speed NO use 100f s no use PAL Audio Enable CAM 1 CAM1 CAM16 OFF REC 38 8 16 Channel Digital Video Recorder AumEmbe Monon Brabe Alarm Very low Low Motion Level Normal setting Normal High Very high Schedule setting OFF OFF ON Baud Rate 2400 2400 4800 9600 19200 38400 P B IP Address 192 168 1 111 Protocol PELCOP PELCOPD Protocol PELCOP Setting LILIN NENO 39 8 16 Channel Digital Video Recorder 18 Remote Control ZOOM FREEZE AUTO m All the function of the DVR c
50. the DVR is in schedule state there will be a 5 symbol on screen press again this button to quit schedule mode If not in shift mode press this button to see big picture of channel 10 While inputting numbers this button is used as number key of 0 11 Menu Menu key press this button to enter system setup menu in menu setup mode press this button to save settings and quit current menu 12 Search Search key press this button to enter search menu please refer search play in user guideline for details 4 Channel Choosing Control Area 16ch 21 8 16 Channel Digital Video Recorder 1 Big picture up Press this button to see full screen re press this button to see the next channel While selecting menu items press this button to move up the cursor 2 Four pictures down Press this button to see four pictures display re press this button will display next four pictures While selecting menu items press this button to move down the cursor 3 Nine pictures left Press this button to see nine pictures display re press this button to see eight pictures While selecting menu items press this button to move the cursor leftward 4 Sixteen pictures right Press this button to see sixteen pictures display re press this button to see thirteen pictures While selecting menu items press this button to move the cursor rightward 5 Enter While selecting menu items press this button to select the item While play
51. tional levels of image quality very high high normal low Record and playback frame rate changeable for recording e Compression mode Modified MJEPG e Compatible with NTSC and PAL format e Support alarm recording and time recording e Multi function searches be able to distinguish different alarm records and time records from ordinary records be able to search by time by segment or by event e Support various playback modes pause several fast forward and backward play modes e Support zoom auto function watermark security e 8 16 alarm input and relay alarm output e Equipped with remote device and PTZ control enable e Support loss and motion detection functions e Triplex operation can play back and search play while it is recording e Support network view e Support USB backup and CD RW backup e 480 frames NTSC PAL is 400 per second for view 120 frames NTSC PAL is 100 per second for recording 8 16 Channel Digital Video Recorder Table of Contents LOSING THE SEED 1 2 4 NCCBSSEINGSEHEJVIENU _ __ 6 6 kann 1 SOS YSTEM OE UP EE 2 7 TIMELDATE SET outre en 2 SC aaa 3 G FACTORY RESET Sagas alias 4 7 CHANGE PASSWORD M 4 SG BIRM WARE UPDATE ue od bete nique eU e et 5 SSH eR 6 ID
52. upports Local when video is playing click Local button the video will save to the computer you can play the file with this software please refer to File Play Live Operation if the software is in live mode click Live Play then click Play it will connect to the DVR and the live pictures will be transmitted to display on the window Click Stop it will stop transmitting pictures Net Search operation if the software is in net search mode click PlayBack net search window will display First you should select the HDD of the DVR Live PlayBack Scanlisk FilePlay Event List HDD iet Record Click the Get Event List button then click Select Event List 1f the DVR has event list you can see the window below Lastblg a index LBA Hane _ Ed 05 05 01 19 50 53 mation 13400 05 05 01 19 51 38 motion 12 Cancel start time Double click the event list you can see the playback video The record list operation is the same as event list operation Drive Scan Connect the HDD that used in the DVR to a PC and then select Drive Scan Drive Scan window will display click and select one HDD then you can play all the video on the HDD 43 8 16 Channel Digital Video Recorder Live PlayBack ScanDisk FilePlay p Semmi Ds Physical Speed 0720 6 09200 Re File play if the s
53. ush the SCHEDULE button then enter the password to stop time recording Because Time recording 15 reliant on the system being set with the correct time you must adjust the time to your correct local time before using this function 6 Playback Push the PLAY button and the system will begin to play the images recorded from the start of the most current recording If the recording is playing push the PAUSE button to pause playing push the PLAY button again to resume normal play To use Fast Forward playing or Fast Backward playing push the FORWARD or REW button while the recording is playing to see faster playback Push the PLAY button to return to normal speed playing from the current place Continuous pushing of the FORWARD button will change the fast forward between five levels of speed X2 X4 X8 X16 X32 in sequence Continuously pushing the REW button will change the fast backward playback between four levels of speed X2 X4 X8 X16 in sequence 28 8 16 Channel Digital Video Recorder During playback mode press the Single Frame Forward button to play a frame at a time and hold the button in to continually play one frame at time while the button is held During playback mode press the Single Frame Rewind button to play back a frame at a time and hold the button in to continually play one frame at time while the button is held Push the PLAY button again to resume normal playback speed or push the STOP button to stop pl
54. will then boot the DVR and it will start to work 2 Turn off the DVR Only turn off the DVR when the system is inactive Do not to turn off the DVR while playing or doing the System Setup Turning off the DVR while recording may cause the recording to corrupt and can cause the HDD to be unreadable in some cases Push the Record button to stop recording or push Stop button to stop playing or exit from System Setup menu then turn off the power If do not wish use the video recorder for a long time you should pull out the power line from the electrical outlet and store the unit where it will not be damaged 3 Normal Recording Connect the power to all related equipment ensure that there is video input using direct connection to your TV or VCR Push the Display button to check spare space of the hard disk if there is not much space please consider changing your hard disk first or select Overwrite mode Check recording parameter setup before recording select video quality frame rate Note that you cannot change record setting during the process of recording Manual recordings are the normal recording condition Under the manual mode non schedule status pushing the Record button will record all channel s video Push the Record button to begin recording four channels will start simultaneous recording While in normal recording mode push the Record or Stop button and enter the right password to stop recording During the process
Download Pdf Manuals
Related Search