User Manual for COMe Eval Type 2 Carrier Board
Contents
1. Specification Functional Specification COM Express baseboard compatible to Type 2 pin out based modules ATX EPS 20pin 4pin power connector 1x PEG x16 slot 1x PCI Express x4 slots 1x PCI Express x1 slot multiplexed with Express card 0 2x PCI standard slots 1x mini PCI socket 4 XSATA 1x LVDS JILI FFC 40 connector 1x VGA 1x 1x 10 100 1000 MBit LAN RJ45 connector 4x USB 2 0 standalone connectors 2x USB 2 0 shared with GBE connector USB 4 and 5 1x USB 2 0 USB 7 on Express Card 1x USB 2 0 USB 6 on miniPCI Expres Feature Connector MARS Compatible LPC Firmware Hub and SPI Flash support for external BIOS Front panel features HDD Act Reset and Power Switch IDE support Compact Flash support SIO Status LED GPIO 10 pin header 4 digit Port 80 81 POST code display with POST code control No LID and SLEEP support COM Express Eval Carrier Type 2 Power Control functions Power Button override module single supply power consumption measurements Realtek ALC886 HD Audio Audio Jack 6 in 1 PWM FAN and Hardware Monitor connectors FAN Voltage COM Express Eval Carrier Type 2 3 2 Block Diagram BLOCK DIAGRAM 3 3 Mechanical Specification Size 243 8mm x 304 8mm max height on top 3 81mm Connector J7 PCB thickness 1 55mm 10 COM Express Eval Carrier Type 2 3 4 Electrical Specification Supply Voltage ATX Main Power 24pin Power Supply Rise time2. The input voltages shall rise from lt 10 of nominal to within the regulation ranges within 0 1ms to 20ms There must be a smooth and continuous ramp of each DC input voltage from 10 to 90 of its final set point following the ATX specification Supply Voltage Ripple Maximum 100 mV peak to peak 0 20MHz 3 5 Environmental Specification Ambient temperature Operating 0 to 60 C Non operating 30 to 85 C Humidity Operating 10 to 90 non condensing Non operating 5 to 95 non condensing 3 6 MTBF The following MTBF Mean Time Between Failures values were calculated using a combination of manufacturer s test data if the data was available and a Bellcore calculation for the remaining parts The Bellcore calculation used is Method 1 Case 1 In that particular method the components are assumed to be operating at a 50 96 stress level in a 40 C ambient environment and the system is assumed to have not been burned in Manufacturer s data has been used wherever possible The manufacturer s data when used is specified at 50 C so in that sense the following results are slightly conservative The MTBF values shown below are for a 40 Cin an office or telecommunications environment Higher temperatures and other environmental stresses extreme altitude vibration salt water exposure etc lower MTBF values System MTBF 264194 hours 2 40 C COM Express Eval Carrier Type 2 4 Connector Lay
3. Clock Buffer U21 Firmware Hub Socket U22 SPI Flash U28A U28B EPM1270F256 CPLD U29 Express Card Power U38 SD Card GPIO Switch U41 FRU EEPROM U42 V3 3_S5 DC DC U45 V1 5 SO DC DC U56 PCI Clock Buffer COM Express Eval Carrier Type 2 5 Connectors and Features 5 1 Power supply 5 1 1 ATX connector The COM Express Eval Type 2 power supply follows the ATX 2 x specification and the baseboard should be supplied by connecting an ATX PSU with 24 pin ATX J55 and 4 pin ATX_12V J54 supply cable in correct orientation The 4 pin ATX_12V connector mainly supplies power to the module Pin ATX Main Power Pin ATX Main Power 1 Orange 3 3V 13 Orange Brown 3 3V 3 3V sense 2 Orange 3 3V 14 Blue 12V 3 Black GND 15 Black GND 4 Red 5V 16 Green Power on 5 Black GND 17 Black GND 6 Red 5V 18 Black GND 7 Black GND 19 Black GND 8 Grey PWR_OK 20 No connection 9 Purple 5VSB 21 Red 5V 10 Yellow 12V 22 Red 5V 11 Yellow 12V 23 Red 5V 12 Orange 3 3V 24 Black GND Pin ATX 12V Pin ATX 12V 1 Black GND 3 Yellow Module VCC 12V nominal 2 Black GND 4 Yellow Module VCC 12V nominal COM Express Eval Carrier Type 2 5 1 2 Reset and Power button COM Express Eval Carrier Type 2 The COM Express Eval Type 6 provides an onboard Reset Button SW3 and Power Button SW4
4. Connector Function SW4 Power Button SW3 Reset Button COM Express Eval Carrier Type 2 COM Express Eval Carrier Type 2 5 2 COM Express connector The COM Express Eval Type 6 is an evaluation carrier board for Type 6 based Computer on Modules The type 6 module pin out is based on two connectors with 2 rows Row A and B and Row C and D with 440 pins overall 220 pins for each of the two connectors Please refer to your module documentation for detailed pin out descriptions ARTET B 42 COM Express Eval Carrier Type 2 5 3 Serial ATA The COM Express Eval Type 6 provides 4 7 pin SATA data connectors as standard 1 27mm Pitch Serial ATA High Speed Header with Locking Latch 1 Ground J18 SATA 0 2 Transmit J19 SATA 1 3 Transmit J26 SATA 2 4 Ground J29 SATA 3 5 Receive 6 Receive 7 Ground 5 4 Storage and GPIO This carrier board supports connections for various storage media including CompactFlash and microSD Also available is connection for GPIO Consult your module manual for what GPIO it is enabled to communicate with GPIO J48 PIN Description GPIO J48 Pin COM Express Eval Carrier Type 2 Description 1 VCC 3 3V 2 GPOO SD_CLK 3 GPIO SD DATAO 4 GP01 SD CMD 5 GPI1 SD DATA1 6 GP02 SD WP 7 GPI2 SD_DATA2 8 GP03 SD_CD 9 GPI3 SD_DATA3 10 GND A SD Card is detected if Card Detect is at low level The write protection is
5. D indicators along the side of the board design These are noted in the chart below and circled in the picture of the carrier board included at the end of this section LED Function D29 Hdd Activity D30 Module Rev 2 D31 Module Type 1 D32 Module Type 2 D33 Module Type 3 D34 Module Type 4 D35 Module Type 5 D36 Module Type 6 D37 Module Type 10 D38 Watchdog D39 THRMTRIP D40 SUS_S5 D42 SUS_S4 D43 SUS_S3 D44 SUS_STAT D45 V3 3_S5 D46 V5 0_S5 D47 V1 5 SO D48 V3 3 SO D49 V5 0 SO D50 V12 AUX SO D51 V12 SO D54 V 12 SO COM Express Eval Carrier Type 2 i I COM Express Eval Carrier Type 2 10 Document Revision History Revision Date Edited by Changes 10 22 Jun 2012 CVG Initial release 1 01 5 Jul 2012 NYP Update multiple sections 1 2 3 4 5 9 10 due to engineering input Corporate Offices COM Express Eval Carrier Type 2 Europe Middle East amp Africa Oskar von Miller Str 1 85386 Eching Munich Germany Tel 49 0 8165 77 777 Fax 49 0 8165 77 219 info kontron com North America 14118 Stowe Drive Poway CA 92064 7147 USA Tel 1 888 294 4558 Fax 1 858 677 0898 info us kontron com Asia Pacific 17 Building Block 1 ABP 188 Southern West 4th Ring Beijing 100070 P R China Tel 86 10 63751188 Fax 86 10 83682438 info kontron cn
6. G kontron Kontron User s Guide COM Express Type 2 Evaluation Carrier Document Revision 1 01 If it s embedded it s Kontron Table of Contents 1 1 1 2 1 3 1 4 1 5 1 6 3 1 3 2 3 3 3 4 3 5 3 6 4 1 4 2 4 3 5 Usar Intermskibfk necs ea as E d DIR ken d ka d basa E SR ER M POR W b se k n b kesan About This Document sesseeno une nene ben wee wen wen Hen Hek Hek He H HEN HA HA WEHA We HA WEHA We HA WEHA We HA W WAR 4 Copyright NOCICE PERENNE 4 Trademarks eee eee eee eee k we s N G ni Se wes de se V ESEN k K e e E N 85e SEK EWE SEA S KOSE KU Ge S e V EE 4 Standards y di yy 335k sal sard kak N Vu N Vu d WERK MO MAME We VVE bu VERA KUVE K VER Nu DE VE E VO A sO Wu HH EDIKE RE ENA 4 Warranty sis ki sekana kak kes ke W b WU M Wu W O 0334 b 5 Technical SUDDOL CDD Secda eu desi ku esen eee WE WU Hu kn SUN EKE xw na wa WU SE WE U H Se MP 5 iti OU UEDION s suya DIEN ERE PAS as k k ne bun awe uk We QVE E E HN ex GUN EE ese E V n D SHECITICAUION M d Functional Specification PR 7 Block Diagrami scvscuccscsacsccsscciee
7. VU k avea UN aU P OL Security V GO s nii v Miu Hh X Document Revision History 5 55 055 oae oas erano anus ano van anao eoa napa sano seosses BD COM Express Eval Carrier Type 2 1 User Information 1 1 About This Document This document provides information about products from Kontron and or its subsidiaries No warranty of suitability purpose or fitness is implied While every attempt has been made to ensure that the information in this document is accurate the information contained within is supplied as is and is subject to change without notice For the circuits descriptions and tables indicated Kontron assumes no responsibility as far as patents or other rights of third parties are concerned 1 2 Copyright Notice Copyright 2003 2012 Kontron Embedded Modules GmbH All rights reserved No part of this document may be reproduced transmitted transcribed stored ina retrieval system or translated into any language or computer language in any form or by any means electronic mechanical photocopying recording or otherwise without the express written permission of Kontron Embedded Modules GmbH DIMM PC PISA ETX ETXexpress microETXexpress X board DIMM IO and DIMM BUS are trademarks or registered trademarks of Kontron Embedded Modules GmbH Kontron is trademark or registered trademark of Kont
8. active read only if SD_WP is at high level The switching circuitry J41 short jumper SD card open jumper GPIO which selects GPIO or SDIO interface may influence the signal quality of SDIO which results in detection or boot issues with some fast SD SDHC cards Therefore it s recommended to reduce SDIO interface speed to 24MHz in module s BIOS if supported COM Express Eval Carrier Type 2 5 5 H gh Definition Audio The COM Express Eval Type 2 provides HDAudio via Realtek ALC886 High Definition Audio Codec supporting analog optical and digital audio connections Audio Connector J7 Speaker Configuration The Audio Connector J7 on the COM Express Evaluation Board is a 5x Audio Jack plus SPDIF Arrangement is as follows Orange Center Blue Line In Black Rear Green Front SPDIF Pink Mic Note1 Audio is only supported with HD Audio compatible COM Express Modules 5 6 The COM Express Eval Type 2 provides a RJ45 Dual USB Combo with a single RJ45 in combination with 2 USB ports USB 4 6 Ethernet Connector J6 with integrated magnetics and LED is configured to support modules with10 100 1000 J6 LED function Activity Link10 Function J61 Left LED Off J61 Right LED COM Express Eval Carrier Type 2 Status LED Link100 Yellow D71 Link1000 5 7 The COM Express module s USB ports 0 to 5 are available on rear panel co
9. d Replacable Unit U41 at I2C address OxAF The default setting is write protected This is for Kontron factory use and not recommended for non Kontron modification COM Express Eval Carrier Type 2 6 Battery Information RTC Battery Socket with VCC RTC clear button R372 Ak 5 BAT64 05A 10083 287 211 004 1036 4714 Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions The battery of this product is not considered to be accessible by the end user Therefore the instructions are only given in English German French Danish Finish and Spanish language If the battery of this product however is accessible by the end user it is in the responsibility of Kontron customer to give the corresponding safety instructions in the required language s COM Express Eval Carrier Type 2 7 Power Distribution COM Express Eval Carrier Type 2 8 Security Advice To protect the external power lines to peripheral devices the customer has to take care about The wires to the external device have the right diameter to withstand the maximum available current The housing of the external device fulfils the fire protection requirements of IEC EN 60950 COM Express Eval Carrier Type 2 9 LED Indicators For user convenience Kontron has included some LE
10. dssatecsctscuuccessassscssassaecsscaasstsvecdessscecesscsscucccsssssessssassccsesccusessccescessss 8 Mechanical Specification sesin cuskse E s s s s cedel k Hae We HER Ane ken ENO GUM SH B S KEN Ou e s U HS Su SEQ Ok SEKE 8 Electrical Specification T 9 Environmental Specification eee e eee e ka kek keskek E k K kw a RA dun eese RO WANA 9 MIL senc serv naa RES di Keke ROKA N c wa b g 1h h ke Su KU A ER W Ke k SEWA S 5 bu S RO W N S H WE k m 9 wong 9i TO Rear Panel 26 6 5 50 90235 55000012320 2090 SEWE ERN a9333 400 5060334138504 SWE000 0492334 sectes 0333340050005501 5y c 10 Connector LOCATIONS c si sis s suyekan n ek k ago ANS GE SERR ENO ace eco cena Ek EE KER EU ka ces cace see 0804 11 Component oVerVIGW oasis voe ae ee essen sa s da su seke k k e Pee nu RA RA es da nu W d ona e a c n 4 ee n WA WERAN 12 Connectors and Fea tUr S ss ssssssesssesssesoosesooseooseoosco occo osccoscoo c LG 5 1 Power SUPPLY 4 5 s5 5544s base sas us ke ke cuna a SER Ee UNA S G OW U VO VO bO RSS W n cS VEK ONE KO 3 9 HK SU UE Q SERU e Ce
11. interfaces for Smart Battery Power Control Signals COM Express Eval Carrier Type 2 5 11 VGA On COM Express Eval Type 2 the VGA output J1 5 12 LVDS The 40 pin JILI LVDS panel connector J36 allows connecting a flat panel directly to the module s dual channel LVDS output Check your module documentation for available BIOS configurations for this flat panel output Pin LVDS Signal Pin LVDS Signal 1 NC 21 LCDD013 2 LCDDOO 22 DETECT GND 3 LCDDO1 23 LCDDO14 4 ENAVDD 24 LCDDO15 5 LCDDO2 25 GND 6 LCDDO3 26 LCDD016 7 NC 27 LCDD017 8 LCDDO4 28 GND 9 LCDDO5 29 LCDDO18 10 GND 30 LCDDO19 11 LCDDO6 31 5V 12 LCDDO7 32 5V 13 GND 33 5V 14 LCDDO8 34 5V 15 LCDDO9 35 BLON 16 JILI_DAT 36 GND 17 LCDDO10 37 GND 18 LCDDO11 38 12V 19 JILI_CLK 39 12V 20 LCDDO12 40 12V COM Express Eval Carrier Type 2 COM Express Eval Carrier Type 2 5 13 External BIOS The COM Express Eval Type 2 supports external boot By closing Jumper J27 the module s onboard BIOS is disabled and the system will boot from an external Firmware Hub in U21 PLCC socket For modules supporting SPI boot the COM Express Eval Type 2 provides a SPI socket U22 for an optional available SPI Flash SPI is part of COM O Specification Rev 2 0 and external SPI boot can be enabled by closing Jumper J27 Please check the documentation of yo
12. k A d k 14 5 1 1 ATXconnector PETICIONES 14 5 1 2 Reset and Power DUL OB s 5 4si5 5i ot aoa oer a so sa ar S00 oia sae pas sone eo ea says 344 See Vases aono sao aereo SEU PE Rasa k 16 www kontron com 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 10 www kontron com COM Express Connector s ssessccccvsssesssbesecccacesssessvesscececssssessodseessavocsessssscenesenecessssescueceavescessesdecsens 18 Serial ATA ssscsssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssssseess 19 Storage ANG GPI m O GEL 19 High Definition Audio ecce eee eene eene eee ee nenne EW nnne eee Kuna n s la USE W HES SO G a VU 21 Ethernet i 4444444553443 lasse cdot esta dot cos nues sea ages ee denses 905414040044000 04 03405340 eddo seen don k W U aaa sad de 22 PClexpress and Express Card 5 y l x sese dk u ek ene rek la eee a kule trennen j c S WA wek E Hae Vu Wu HE d Hun a e U HEE Ken eee 24 MARS COR O C O s uc ss e kene se kal ka e kek kek e EKE O WARA BR dec asia sa a b ka eku EEE V k k w dass soda ue EW KE RENE ES G VVE G n VE dde 25 Ba tt ry Informati O a cata ses oaie aia ma kan OO Power Distribution er 5 900 90a 095 a ke 9o
13. lp you use our products in your systems Please consult our Web site at http www kontron com support for the latest product documentation utilities drivers and support contacts Consult our customer section http emdcustomersection kontron com for the latest BIOS downloads Product Change Notifications and additional tools and software In any case you can always contact your board supplier for technical support COM Express Eval Carrier Type 2 2 Introduction The COM Express Evaluation carrier board for Type 2 modules is designed to allow embedded application developers to get up and running quickly on the COM Express basic and compact form factors giving them a head start on the total system design Simply select a pin out Type 2 COM Express CPU module then Plug amp Go The Kontron COM Express Eval Type 2 is an evaluation backplane for COM Express Computer on Modules following the PICMG COM O specification with pin out Type 2 Ordering Information Article Part No Description COM Express Type 2 Evaluation Carrier 38104 0000 00 1 Evaluation Board COM 0 pin out Type 2 3 3 1 gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y gt Y
14. nnectors J4 J5 and J6 USB port 6 is used on Express Card connector and USB port 7 is used for the miniPCI Express card connector The COM Express Eval Type 2 provides USB up to 8 ports with 2 on RJ45 USB Combo connector J6 4 as standalone J4 J5 1 shared with Mini PCIe and 1 shared with the ExpressCard Green COM Express Eval Carrier Type 2 5 8 PCI The COM Express Eval Type 2 supports 32 bit PCI 5 9 PCIexpress and Express Card COM Express Eval Carrier Type 2 The COM Express Eval Type 2 provides one x4 one x1 PCIexpress x1 slots one Express Card Slot and one Mini PCIe Connector Function J25 PCIe Graphics J23 PCIe x4 0 3 J22 J47 PCIe x1 4 or Express Card multiplexed by J63 open Express Card closed PCIe x1 connector Express Card supports 34 and 54 PCIe 4 USB 7 J49 PCIe Mini Card PCIe 5 USB 6 Express Card The Express Card Slot J47 in combination with USB 7 allows 1 3A on 3 3V 275mA on AuxPower and 650mA on 1 5V continuous Card Power with pin out in table below Pin J41 Signal Pin J41 Signal 1 GND 14 3 3VS_1 2 USB_D 15 3 3VS_0 3 USB_D 16 CLKREQ 4 CPUSB 17 CPPE 5 NC 18 REFCLK 6 NC 19 REFCLK 7 SMB_CLK 20 GND 8 SMB_DATA 21 PERNO 9 1 5V 2 22 PERPO 10 1 5V 1 23 GND 1 COM Express Eval Carrier Type 2 5 10 MARS connector The MARS connector J50 provides additional
15. out 4 1 Rear Panel COM Express Eval Carrier Type 2 4 2 Connector Locations 4 3 Component overview Connector Short Description BT1 D29 D30 D31 D32 D33 D34 D35 D36 D37 D61 D62 D63 D64 J1 J4 J5 J6A J6B J7 J11 J65 J14 J16 J17 J18 J19 J26 J29 J20 J22 J23 J25 J27 J28 J31A J31B J32 J36 J39 J43 J38 J46 J47 J49 J50 J54 J55 J56 J71 J72 J73 J74 J75 J76 J77 J79 J80 COM Express Eval Carrier Type 2 RTC Battery Socket HDD Activity LED Module Type LEDs POST Code Port 0x81 and Port 0x80 VGA 2x Dual USB 3 0 Gigabit Ethernet Dual USB 2 0 5x Audio Jack SPDIF Internal Audio CD in Side SMBus Header S PDIF Header I2C Header SATA Ports LPC Slot PCIe x1 PCIe x4 PCIe Graphics BIOS Disable Jumpers COM Express AB Connector COM Express CD Connector SPI Flash Dediprog Connector LVDS 2x Fan Header Fan Power MicroSD Card Express Card PCIe Mini Card Feature Connector MARS Compatible ATC Connector 4 pin ATX Connector 24 pin GPIO Connector CompactFlash IDE PCI 32 bit 3 3V 5V Card Slots A amp B COM1 COM2 Parallel port Keyboard Mouse SIO GPIO Header Connector Short Description COM Express Eval Carrier Type 2 SW3 Reset Button SW4 Power Button SPK1 PC Buzzer U3 Audio Codec VR U4 Super 1 0 U12 Audio Codec U20 PCIe
16. ron AG 1 3 Trademarks The following lists the trademarks of components used in this board IBM XT AT PS 2 and Personal System 2 are trademarks of International Business Machines Corp Microsoft is a registered trademark of Microsoft Corp Intelis a registered trademark of Intel Corp Allother products and trademarks mentioned in this manual are trademarks of their respective owners 1 4 Standards Kontron is certified to ISO 9000 standards COM Express Eval Carrier Type 2 1 5 Warranty This Kontron product is warranted against defects in material and workmanship for the warranty period from the date of shipment During the warranty period Kontron will at its discretion decide to repair or replace defective products Within the warranty period the repair of products is free of charge as long as warranty conditions are observed The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer unauthorized modification or misuse operation outside of the product s environmental specifications or improper installation or maintenance Kontron will not be responsible for any defects or damages to other products not supplied by Kontron that are caused by a faulty Kontron product 1 6 Technical Support Technicians and engineers from Kontron and or its subsidiaries are available for technical support We are committed to making our product easy to use and will he
17. ur module if SPI is supported and which SPI Flash size is required Booting from external BIOS Close Jumper J27 to boot from the baseboard s SPI Flash Flashing the external BIOS Prepare a bootable USB flash drive and save BIOS and flash utility in the root folder Please check Application Note KEMAPO46 avialble at Kontron s customer section for more details Open J27 to boot from the module s BIOS Poweron the system and boot from our USB flash drive Close J46 to enable the LPC FWH or close J75 to enable the SPI Flash Execute the BIOS update command e g afudos exe bios rom P B N C X Reboot your system if flash procedure has finished Your system should now start from external BIOS Note Please check module documentation if external boot from LPC FWH and or SPI Flash is supported Warning Do not close both jumpers at the same time COM Express Eval Carrier Type 2 5 14 CPLD amp POST Code Display Power Management control 4 digits LPC PCI Port 80 81 Post Code and additional GPIOs are implemented in onboard Altera CPLD U28 Port 80 81 POST Code The 7 segment display D63 D64 for Port 81 and D61 62 for Port 80 shows BIOS status codes during boot up process 5 15 FAN The COM Express Eval Type 2 provides two 4 pin J39 J43 fan connectors 5 16 FRU PROM I2C EEPROM Following the new COM Express specification the COM Express Eval Type 2 provides an I2C EEPROM The FRU PROM Fiel
Download Pdf Manuals
Related Search