WADE-8156 User`s Manual
Contents
1. WADE 8156 Intel Core 2 Duo Desktop Q965 Mini ITX User s Manual Rev 1 0 2007 04 25 WADE 8156 User s Manual Copyright All rights reserved The information contained in this guide has been validated and reviewed for accuracy No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this guide the Manufacturer assumes no responsibility for errors or omissions No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Manufacturer Trademark Intel Pentium and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation All products and company names are trademarks or registered trademarks of their respective holders These specifications are subject to change without notice Technical Support We hope you to get the maximum performance from your products and be willing to help if running into technical difficulties For the most frequently asked questions it s easily found answers from the product documentation and usually a lot more detailed so please take reference to this manual first If the answer still can not be found gather all the information or questions applying to the prob2. Item Description GER This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled This setting informs the PCI devices that an ISA based Graphics device is installed in the system It does this so the ISA based Graphics card will function correctly This does Enabled not necessarily indicate a physical ISA adapter card The graphics chipset can be mounted on a PCI card Always check with your adapter card s manuals first before modifying the default settings in the BIOS 4 1 3 6 PCI IDE BusMaster Set this value to allow or prevent the use of PCI IDE busmastering 4 1 3 7 OffBoard PCI ISA IDE Card Set this value to allow the OffBoard PCI ISA IDE Card to be selected 4 1 3 8 IRQ3 4 5 7 9 10 11 14 15 Set this value to allow the IRQ settings to be modified Item Description Available This setting allows the specified IRQ to be used by a PCI PnP device Reserved This setting allows the specified IRQ to be used by a legacy ISA device 42 55 WADE 8156 User s Manual 4 1 3 9 DMA Channel 0 1 3 5 6 7 Set this value to allow the DMA setting to be modified Item Description Available This setting allows the specified DMA to be used by PCI PnP device Reserved This setting allows the specified DMA to be used by a legacy ISA device 4 1 3 10 Reserved Memory Size Set this value to allow the system to reserve memory that is u
3. Available IRQS Available IRQ10 Available IRQ11 Available IRQ14 Available IRQ15 Available DMA Channel DMA Channel DMA Channel DMA Channel DMA Channel DMA Channel Available Available Available Available Available Available Select Screen Select Item Change Option General Help Save and Exit Exit v02 61 C Copuright 1985 2006 American Megatrends Inc 41 55 WADE 8156 User s Manual 4 1 3 1 Clear NVRAM Clear NVRAM during System Boot 4 1 3 2 Plug amp Play O S Set this value to allow the system to modify the settings for Plug and Play operating system support Item Description We The No setting is for operating systems that do not meet the Plug and Play specifications It allows the BIOS to configure all the devices in the system SS The Yes setting allows the operating system to change the interrupt I O and DMA settings Set this option if the system is running Plug and Play aware operating systems 4 1 3 3 PCI Latency Timer Set this value to allow the PCI Latency Timer to be adjusted This option sets the latency of all PCI devices on the PCI bus The options 32 64 96 128 160 192 224 248 PCI clock cycles 4 1 3 4 Allocate IRQ to PCI VGA Set this value to allow or restrict the system from giving the VGA adapter card an interrupt address 4 1 3 5 Palette Snooping Set this value to allow the system to modify the Palette Snooping settings
4. Serial ATA 3 amp 4 connectors Internal speaker connector System fan connector Internal USB 5 6 amp 7 8 connectors USB 1 2 amp RJ 45 LAN 1 connectors USB 3 4 amp RJ 45 LAN 2 connectors D sub 15 pin VGA connector 16 55 WADE 8156 User s Manual REMARK 3 x 1 header REMARK 2 x 5 header Audio jack x 3 1x3 wafer 1 x 4 header 2 x b header 1x4 wafer 2 x 5 header 2 x 5 header 1 x 4 header 1x3 wafer 2 x 5 header 2 3 Jumpers Connectors Setting 2 3 1 RTC CMOS Clear Select JP1 PINNo Description Clear CMOS Normal operation WADE 8156 User s Manual 2 3 2 Internal Audio for Chassis AUDIO1 PINNo Description 2 3 3 Audio Connector AUDIO2 BNNo Description Bue 2 Green 3 Red 2 3 5 CD In from CD ROM CD1 Bo Description SSES ER NEE a 8 UNERR 6 Gowd 8 Key eo NEL 2 3 4 Auxiliary CPU System Connectors AUX FANI CPU FANI SYS_FAN1 Description GND 12V SENSE Control CPU_FAN1 only 2 3 6 COM1 COM2 Connector COM1 COM2 Ring Indicator 10 COM Key 17 55 WADE 8156 User s Manual 2 3 7 GPIO Connector GPIO1 2 3 8 PS 2 Keyboard amp Mouse KBMS1 pn Description 2 General Purpose Mo bit27 a General Purpose MO bit 28 6 General Purpose VO bit33 8 GeneralPurposelObit34 9 GeneralPurposelObit26 2 3 9 Front Side Indicators PANEL 1 2 3 10 24 pin ATX Power C
5. Oocoooocooooo OOOOOOOOOOON PSG E 0000000 20000m 90000 sooo 00000000000020000220 o9900 Ve EET 999 oo o gt f 00 y Q SE GAR 15 9900665 2556 0009900695 2222023035 LIIIIS TEELE 000000000900909 000090090900000 EEN waa 90 000001 200020 ao00cac0000000000000000 v0600000000000000000 200002 00000 200 ooo 000009000000000000000000000000000 g o o o o o o o e o o o 2 o o o WI 2 o o o o 2 2 o o o o o 2 2 o o o o 2 2 o o o o 2 o o o 49000002000000020000200000C Jg ES 2252000 00000 Bees d Co 1 AuDIO1 BOSS AUDIO2 OococoQ 0000 O O y Oo USB2LAN2 15 55 2 2 Jumpers amp Connectors JUMPERS JP1 CONNECTORS AUDIO1 AUDIO2 AUX FANI CD1 COM COM CPU FANI DIMM1 DIMM2 GPIO1 KBMS1 PANEL1 PCI E1 PWR1 PWR2 SATA1 SATA2 SATA3 SATA4 SPK1 SYS FANI USB1 USB2 USB2LAN1 USB2LAN2 VGA1 FUNCTION RTC CMOS clear select FUNCTION Internal audio for chassis Audio connector Auxiliary fan connector CD In from CD ROM D sub 9 pin serial port 1 connector Serial port 2 connector CPU fan connector 240 pin DDR2 SDRAM 1 amp 2 socket GPIO connector PS 2 keyboard amp mouse connector Front side indicators IDE1 active LED 1 3 System power on LED 2 4 System reset 5 7 System power on switch 6 8 PCI Express x16 slot 24 pin ATX power connector 4 pin ATX power connector Serial ATA 1 amp 2 connectors
6. WADE 8156 User s Manual Dimensions 1 5 O OT o gt word aco E b 98 2 EERBARE N 92 e 88 23 ag Xi ee ee SS 2 San evo amp c Bm 23 we E E 00 0L E e EE AA E MET ES __ _ oocorressee ege 5 8 91 YT A Tis 3 bi Vox h ooooooooooooooqoooooooooopoooooooq ood Ly Oo SL sel LL TE EI 9 te ee es Laai ma SINT pe EZ ES Sisi 6E BELL la Ollesesieses EE EE EE O olkae E T o ollesociosos x o olfeszasese Ed SEA 320i OCI S LOL oe ele EE E LE O olsese o S o op Ji o olfpssdaess i G 68 ape 99 48 Em E Sazi 9 01 E GE 9 bt Ae S 00 0 00 0 CH e mj mM 170 00 165 10 138 84 120 46 96 4 48 4 45 34 13 55 lp CHAPTER 2 WADE 8156 User s Manual 2 Hardware Configuration Setting This chapter gives the definitions and shows the positions of jumpers headers and connectors All of the configuration jumpers on WADE 8156 board are in the proper position The default settings shipped from factory are marked with an asterisk In general jumpers on the Mini ITX are used to select options for certain features Some of the jumpers are designed to be user configurable allowing for system enhancement The others are for testing purpose only and should not be altered To select any option cover the jumper cap over SHORT or remove NC it from the jumper pins according to the following instructions Here NC stands for Not Connect 2 1 Board Layout
7. 4 1 4 1 7 Hit DEL Message Display Set this value to allow the Hit DEL to enter Setup Message Display to be modified 4 1 4 1 8Interrupt 19 Capture Enabled Allows option ROMs to trap interrupt 19 This is required by some PCI cards that provide a ROM based setup utility 45 55 WADE 8156 User s Manual 4 1 5 Security Settings S SETUP UTILITY Change Supervisor Password 4 1 5 1 Change Supervisor Password Indicates whether a supervisor password has been set If the password has been installed Installed displays If not Not Installed displays 4 1 5 2 Change User Password Indicates whether a user password has been set If the password has been installed Installed displays If not Not Installed displays 4 1 5 3 Clear User Password Select Clear User Password from the Security Setup menu 4 1 5 4 Boot Sector Virus Protection Enable Disable Boot Sector Virus Protection 46 55 WADE 8156 User s Manual 4 1 6 Advanced Chipset Settings BIOS SETUP UTILITY gt North Bridge Configuration 47 55 WADE 8156 User s Manual 4 1 6 1 North Bridge Configuration You can use this screen to select options for the North Bridge Configuration Use the up and down Arrow keys to select an item Use the Plus and Minus keys to change the value of the selected option Note The North Bridge Configuration setup screen varies depending on the supported North Bridge chipset BIOS SETUP UTILITY hipset
8. Select Screen Resume On LAN Disabled Select Item Resume On PME Disabled Change ption Resume On RTC Alarm Disabled General Help Save and Exit Exit v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 2 6 1 Power Management APM Set this value to allow Power Management APM support 4 1 2 6 2 Video Power Down Mode This option specifies the length of time the system waits before it enters suspend mode The options Disabled 1 5 10 Min 4 1 2 6 3Hard Disk Power Down Mode This option specifies the power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired The options Disabled Standby Suspend 4 1 2 6 4 Suspend Time Out Go into Suspend in the specified time 4 1 2 6 5 Throttle Slow Clock Ratio In a power management state the BIOS can throttle the CPU clock to reduce power consumption For example a throttle ratio of 50 means the clock is turned off half of its normal operational time The options 87 5 75 0 62 5 50 37 5 25 12 5 36 55 WADE 8156 User s Manual 4 1 2 6 6 Keyboard amp PS 2 Mouse Monitor KBC Ports 60 64 4 1 2 6 7 Power Button Mode This option specifies how the externally mounted power button on the front of the computer chassis is used The options On Off Standby Suspend 4 1 2 6 8 Resume On Ring Disable Enable RI to generate a wake event 4 1 2 6 9 Resume On LAN Disable Enable LAN GPI to generate a w
9. tech Automatic General Help Intel R C State tech Save and Exit C1 Config Standard Exit Hard C4 Config Disabled v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 2 1 1 Max CPUID Value Limit The Intel amp Processor Identification Utility requires the Max CPUID Value Limit in the system BIOS to be disabled for proper processor identification Once processor identification has taken place the option can be re enabled if desired 4 1 2 1 2 Vanderpool Technology Vanderpool Technology allows a platform to run multiple operating systems and applications in independent partitions With VT one computer system can function as multiple virtual systems Note After any change to this option system must be powered off to take effect 4 1 2 1 3 Execute Disable Bit A feature designed to stop buffer overflow attacks against the operating system Buffer overflow attacks are one of the most common tactics used to attack personal computers The processor prevents the execution of code in data only memory pages while enabled and will not restrict code execution in any memory area if disabled This makes the processor more vulnerable to buffer overflow attacks 4 1 2 1 4 Core Multi Processing This item allows to select Core Multi Processing mode 28 55 WADE 8156 User s Manual 4 1 2 1 5Intel amp SpeedStep tm tech Intel R SpeedStep tm tech is Intel s new power saving technology Processor can switch between multiple freque
10. the CPU gently seated in place e Close the load plate and push it back to the original position 5 6 7 Metal level Plastic cap Load plate Pin 1 of the socket Gold triangular mark Note Do not force the CPU into the socket It may bend the pins and damage the CPU 21 55 WADE 8156 User s Manual 3 2 Installing 1 U Cooler for Intel JFC LGA775 Processor Cooler Thermal bracket s paste E BEGSAG 1 Unpacked the cooler with 1 U Cooler Fan 2 Place Cooler Bracket under the board to amp the Thermal paste enclosed make the bracket holes right to the board holes then smear the Thermal paste on the top of CPU Cooler screw CPU fan connector Cooler screw Bracket 3 1 Place the cooler above CPU and make sure four Cooler screws to the right position 3 2 Fasten four Cooler screws 3 3 Plug in the CPU Fan connector Note For a safety landing avoid leaving prongs on hard surface 22 55 WADE 8156 User s Manual 3 3 Main Memory WADE 8156 board provide 2 DIMMs 240 pin Dual In line Memory Module to support 1 5V DDRAM Synchronized DRAM as on board main memory The maximum memory size is 256 MB 4 GB with using 256MB 512MB 1GB 2GB technology Supports up to 2 double sided DIMMs at DDR2 800 MHz The memory architecture adopts 128 bit data interface to support for x8 and x16 DDRAM DDR2 device width In addition it only supports Non ECC memory For system compatibility and stability don t use
11. value to enable or disable the Legacy USB Support The Optimal and Fail Safe default setting is Disabled 4 1 2 9 2 Port 64 60 Emulation Enables I O port 60h 64h emulation support This should be enabled for the complete USB keyboard legacy support for non USB aware OSes 4 1 2 9 3 USB 2 0 Controller Mode Configures the USB 2 0 controller in HiSpeed 480Mbps or FullSpeed 12Mbps 4 1 2 9 4 BIOS EHCI Hand Off This is a workaround for OSes without EHCI hand off support The EHCI ownership change should claim by EHCI driver 40 55 WADE 8156 User s Manual 4 1 3 Advanced PCI PnP Setting BIOS SETUP UTILITY Main fiduanced PCIPnP Boot Security Chipset Exit fiduanced PCI PnP Settings Clear NURAM during System Boot WARNING Setting wrong values in below sections may cause system to malfunction Plug amp Play O S No PCI Latency Timer 641 Allocate IRQ to PCI UGA Yes Palette Snooping Disabled PCI IDE BusMaster Enabled OffBoard PCI ISR IDE Card Auto Select Screen IRQ3 Availablel Select Item IRQ4 Available Change Option IRQS Available General Help IRQ Available Save and Exit IRQS Available Exit IRQ10 Available IRQ11 fva i lable v02 61 C Copuright 1985 2006 American Megatrends Inc BIOS SETUP UTILITY Main fiduanced PCIPnP Boot Security Chipset Exit OffBoard PCI ISA IDE Card Auto Size of memory block to reserve for legacy IRQ3 Available ISA devices IRQA Available IRQS Available IRQ
12. North Bridge Chipset Configuration ENABLE fillou OO remapping of overlapped PCI memory PCI MMIO Allocation 4GB To 2816MB above the total DRAM Frequency Auto physical memory Configure DRAM Timing by SPD Enabled DISABLE Do not allow Initate Graphic Adapter PEG PCT remapping of memory Internal Graphics Mode Select Enabled 8MB PEG Port Configuration PEG Port Auto Select Screen gt Uideo Function Configuration Select Item Change Option General Help Save and Exit Exit v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 6 1 1 Memory Remap Feature ENABLE Allow remapping of overlapped PCI memory above the total physical memory DISABLE Do not allow remapping of memory 4 1 6 1 2 DRAM Frequency The item allows you to set the DRAM frequency 4 1 6 1 3 Configure DRAM Timing by SPD Select the operating system that is selecting DRAM timing so select SPD for setting DRAM timing by SPD The choice Enable Disable 4 1 6 1 4Initate Graphic Adapter Select which graphics controller to use as the primary boot device 48 55 WADE 8156 User s Manual 4 1 6 1 5Internal Graphics Mode Select Select the amount of system memory used by the internal graphics device 4 1 6 1 6 PEG Port This item allows you to control the PEG or on chip VGA The choice Auto Disabled 4 1 6 1 7 Video Function Configuration BIOS SETUP UTILITY DUMT Mode Select DUMT Model 4 1 6 1 7 1 DVMT Mode Select This
13. ST Set this value to prevent the serial port from accessing any system resources When isable this option is set to Disabled the serial port physically becomes unavailable Set this value to allow the serial port to use 3F8 as its VO port address and IRQ 4 for the interrupt address This is the default setting The majority of serial port 1 or COM1 ports 3F8 IRQ4 on computer systems use IRQ4 and I O Port 3F8 as the standard setting The most common serial device connected to this port is a mouse If the system will not use a serial device it is best to set this port to Disabled Set this value to allow the serial port to use 2F8 as its I O port address and IRQ 3 for the 2F8 IRQ3 interrupt address If the system will not use a serial device it is best to set this port to Disabled Set this value to allow the serial port to use 3E8 as its VO port address and IRQ 4 for the 3E8 IRQ4 interrupt address If the system will not use a serial device it is best to set this port to Disabled Set this value to allow the serial port to use 2E8 as its I O port address and IRQ 3 for the 2E8 IRQ3 interrupt address If the system will not use a serial device it is best to set this port to Disabled 4 1 2 3 2 Restore on AC Power Loss by IO This item allows you to select if you want to power on the system after power failure Option Power On Power Off Last state 4 1 2 3 3 Watch Dog Timer Select Enable to set Watch Dog Timer
14. The options 10 20 30 40 Sec 1 2 4 Min 33 55 WADE 8156 User s Manual 4 1 2 4 Hardware Health Configuration CPU FAN Mode Setting Manual Mode 4 1 2 4 1 CPU FAN PWM Control Enable CPU Fan mode 4 1 2 4 2 CPU FAN PWM Control This item allows you to set CPU FAN PWM Control mode 34 55 WADE 8156 User s Manual 4 1 2 5 ACPI Configuration ACPI Aware 0 S 4 1 2 5 1 ACPI Aware O S Set this value to allow the system to utilize the Intel ACPI Advanced Configuration and Power Interface specification Item Description This setting should be set if the operating system in use does not comply with the ACPI No Advanced Configuration and Power Interface specification DOS Windows 3 x and Windows NT are examples of non ACPI aware operating systems This setting should be set if the operating system complies with the ACPI Advanced e Configuration and Power Interface specification This is the default setting Windows es 950 Windows 988 and Windows 20006 are examples of ACPI aware operating systems 35 55 WADE 8156 User s Manual 4 1 2 6 APM Configuration BIOS SETUP UTILITY Advanced APM Configuration Enable or disable l Video Power Down Mode Suspend Hard Disk Power Down Mode Suspend Suspend Time Out Disabled Throttle Slow Clock Ratio 507 Keyboard amp PS 2 Mouse MONITOR Power Button Mode On 0ff fiduanced Resume Event Controls Resume On Ring Disabled
15. ake event 4 1 2 6 10 Resume On PME Disable Enable PME to generate a wake event 4 1 2 6 11 Resume On RTC Alarm Disable Enable RTC to generate a wake event 37 55 WADE 8156 User s Manual 4 1 2 7 MPS Configuration BIOS SETUP UTI MPS Revision Select MPS Revision 38 55 WADE 8156 User s Manual 4 1 2 8 Remote Access Configuration BIOS SETUP UTILITY Remote ccess Disabled 4 1 2 8 1 Remote Access You can disable or enable the BIOS remote access feature here 39 55 WADE 8156 User s Manual 4 1 2 9 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration Enables support for legacy USB AUTO Module Version 2 24 0 12 4 option disables legacy support if USB Devices Enabled no USB devices are 1 Drive connected Port 64 60 Emulation Disabled USB 2 0 Controller Mode HiSpeed BIOS EHCI Hand Off Enabled Select Screen Select Item Change Option General Help Save and Exit Exit v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 2 9 1 Legacy USB Support Legacy USB Support refers to the USB mouse and USB keyboard support Normally if this option is not enabled any attached USB mouse or USB keyboard will not become available until a USB compatible operating system is fully booted with all USB drivers loaded When this option is enabled any attached USB mouse or USB keyboard can control the system even when there is no USB drivers loaded on the system Set this
16. al Power Requirement Power Type Operating Temperature Operating Humidity Size L x W Weight WADE 8156 User s Manual Realtek ALC883 7 1 2 CH audio interface Mic in Line in CD Audio in Line out Rear out and Center Subwoofer out Dual Marvell 88E8053 PCI Express Gigabit Ethernet controllers IEEE 802 3 10BASE T 100BASE TX 1000BASE T 43 3 V 3 3 A 5 V 1 9 A 12 V 9 4 A 5 Vsb 500 mA w Intel Core 2 Duo E6700 2 66 GHz amp 2 x 512 MB DDR2 800 MHz SDRAM in Dos Mode 24 pin ATX power connector 1x 4 pin ATX 12V power connector 0 60 C 32 140 F 0 90 relative humidity non condensing 6 69 x 6 69 170 mm x 170 mm 0 94 Ibs 0 43 Kg 11 55 WADE 8156 User s Manual 14 System Architecture All of details operating relations are shown in WADE 8156 system block diagram Intel Core 2 Duo Desktop Pentium 4 Celeron D Processor FSB 1066 800 533 MHz DIMM1 DDR2 Socket 240 pin 533 667 800 MHz DIMM2 DDR2 Socket 240 pin Intel Q965 i BW 300MB s SATA 4 SATA 3 SATA 2 SATA 1 PCI E x16 PCI Express x16 slot 7 pin 7 pin T pin T pin For optional ADD2 card or standard PCI E x16 Intel ICH8 R graphic card BTX 3 1 AC97 Audio Realteck Jack ALC883 LPC BUS USB V20 PCI E GB PCI E GB LAN Marvell LAN Marvell USB1 USB2 USB3 USB4 USB_LAN 2 ports 2 ports 2 ports 2 ports 8 ports Super VO 88E8053 88E8053 W83627DHG USB_LAN RJ45 12 55
17. ced onboard four SATA high speed data transferring at up to 300 MB s integrated Realtek ALC883 7 1 2 CH high definition audio codec The onboard Super I O Winbond W83627DHG chipset supports two RS 232 serial port interfaces Hardware Monitor function eight Hi speed USB 2 0 ports and two 6 pin Mini DIN connectors for PS 2 mouse and keyboard Besides one 24 pin standard connector designed to support ATX power function and a feature of CPU overheat protection will provide user more security and stability Combing with these outstanding features in the Mini ITX form factor WADE 8156 is definitely the most excellent choice for embedded applications like Network Point of Sales POS automated KIOSKs security products medical instruments and gaming machines 8 55 WADE 8156 User s Manual 1 2 Packing Check List The WADE 8156 package includes the following basic items accompany with this manual One WADE 8156 Mini ITX board Two Serial ATA cables One Serial port cable for COM2 One USB 2 0 cable One UO Shield One Supporting CD ROM contains User s Manual and internal VGA display driver and Marvell Gigabit Ethernet network controller driver and on board devices drivers VV VV ON ON If any of these items is damaged or missed please contact your vendor and save all packing materials for future replacement and maintenance 9 55 1 3 Specifications System CPU FSB BIOS System Chipset UO Chip System Memory Stora
18. disable C Language Example outportb 0x26 0x87 outportb 0x2e 0x87 outportb 0x2e 0x07 outportb Ox2f 0x08 outportb 0x2e 0x2d outportb Ox2f 0x20 outportb 0x26e 0x30 outportb Ox2f 0x01 9 outportb 0x2e 0xf5 10 outportb Ox2f 0x00 11 outportb 0x2e 0xf6 12 outportb 0x2f 0x05 ON OOF WD 54 55 WADE 8156 User s Manual Appendix B GPI O Programming The General Purpose I O pins are provided for custom system design The pin programming as input mode or output mode is depending on the configuration The pin definitions are as the following table GPIOBASE Address 480h Pin No IN OUT Register Address Data Register Address PIN BIT 2 GPIOBASE 04h 3 GPIOBASE 0Ch 3 3 3 GPIOBASE 04h 1 GPIOBASE 0Ch 1 0 4 GPIOBASE 04h 3 GPIOBASE 0Ch 3 4 5 GPIOBASE 04h 1 GPIOBASE OCh 1 7 6 GPIOBASE 34h 40 GPIOBASE 38h 0 1 7 GPIOBASE 04h 2 GPIOBASE OCh 2 4 8 GPIOBASE 34h 0 GPIOBASE 38h 0 2 9 GPIOBASE 04h 3 GPIOBASE 0Ch 3 2 IN OUT Register 0 The respective GPIO PIN is programmed as an output port 1 The respective GPIO PIN is programmed as an input port Data Register Read Write for output port Read Only for input port Configure pin 2 to be an output port and output LOW C Language Example int iret 2 inportb 0x487 iret iret amp 0x08 set bit3 to O outportb 0x487 iret set pi
19. ed off Press Delete when you Power on or Reboot the computer system i e After the logo appears at the center of the screen please press Delete to enter the BIOS setup program In the BIOS make sure that everything is working fine before you try to optimize it for maximum performance 4 1 1 Main Menu BIOS SETUP UTILITY Sustem Time When you enter the AMI CMOS Setup Utility the Main will appear on the screen The Main allows you to select several configuration options Use the left right arrow keys to highlight a particular configuration screen from the top menu bar or use the down arrow key to access and configure the information below 4 1 1 1 System Time System Date Use this option to change the system time and date The date must be entered in MM DD YY format The time is entered in HH MM SS format 26 55 WADE 8156 User s Manual 4 1 2 Advanced Setting N BIOS SETUP UTILITY CPU Configuration 27 55 WADE 8156 User s Manual 4 1 2 1 CPU Configuration The CPU Configuration setup screen varies depending on the installed processor BIOS SETUP UTILITY Advanced Configure advanced CPU settings Disabled for VindouwsXP Module Version 3E 01 Manufacturer Intel Frequency 255MHz FSB Speed 1066MHz Cache L1 0 KB Cache L2 0 KB Ratio Actual Value 7 Vanderpool Technology Enabled Select Screen Execute Disable Bit Enabled Select Item Core Multi Processing Enabledl Change Option Intel R SpeedStep tm
20. ge RAID Watchdog Timer H W Status Monitor GPIO Expansion MIO Internal UO Back Panel VO Display Chipset Display Memory Resolution VGA LCD Interface LVDS DVI WADE 8156 User s Manual Intel Core 2 Duo Desktop Pentium 4 Celeron D processor in the LGA775 package E6000 600 500 300 sequences 1066 800 533 MHz AMI BIOS with 8 Mb SPI Flash EEPROM Intel Q965 ICH8 Winbond W83627DHG UO controller 2 x 240 pin DIMM sockets support dual channel DDR2 533 667 800 SDRAM Max up to 4 GB memory 4 x Serial ATA 300 ports Optional ICH8R supports RAID 0 1 5 10 function Reset 1 sec 255 min and 1 sec or 1 min step Monitoring system temperature voltage and cooling fan status Auto throttling control when CPU overheats System automatically restored on recovery of AC power loss On board programmable 8 bit Digital I O interface 1 x PCI E x16 interface 1 x RS 232 4 x USB 2 0 1 x VGA 1 x Audio jack 2 x RJ 45 1 x RS 232 4x USB 2 0 1 x KB 1 x Mouse Intel Q965 Integrated Intel GMA 3000 graphics Intel DVMT 4 0 supports up to 256 MB video memory Analog display up to 2048 x 1536 75Hz QXGA Digital CRT HDTV up to 1920 x 1080 85 Hz DSUB 15 connector for VGA output Optional Chrontel CH7308 LVDS transmitter by ADD2 card Optional Chrontel CH7307 DVI transmitter by ADD2 card 10 55 Audio HDAC Audio Interface Ethernet Chipset Ethernet Interface Mechanical amp Environment
21. item allows you to select the DVMT mode The choice FIXED DVMT BOTH 4 1 6 1 7 2 DVMT FIXED Memory This item allows you to select the DVMT or FIXED memory size 4 1 6 1 7 3 Boot Display Device This item allows you to select the boot display device 4 1 6 1 7 4 Flat Panel Type This item allows you to select the panel resolution The options 1024 x 768 18 bit 1 CH 1280 x 1024 24 bit 2 CH 1400 x 1050 24 bit 2 CH 1600 x 1200 24 bit 2 CH 49 55 WADE 8156 User s Manual 4 1 6 2 South Bridge Configuration You can use this screen to select options for the South Bridge Configuration South Bridge is a chipset on the motherboard that controls the basic I O functions USB ports audio functions modem functions IDE channels and PCI slots Use the up and down Arrow keys to select an item Use the Plus and Minus keys to change the value of the selected option Note The South Bridge Configuration setup screen varies depending on the supported South Bridge chipset BIOS SETUP UTILITY hipset South Bridge Chipset Configuration Disabled USB 2 0 Controller Enabled 2 USB Ports HDA Controller Enabled 4 USB Ports CPU PCI Clock Spread Spectrum Enabled 6 USB Ports 8 USB Ports SLP_S4 Min Assertion Width 1 to 2 seconds 10 USB Ports PCIE Ports Configuration Onboard LAN 1 Control Auto Onboard LAN 2 Control Auto PCIE Port 2 Auto Select Screen PCIE Port 3 Auto Select Item PCIE Port 4 Auto Change Optio
22. lem and with the product on hand contact your distributor sales representative or customer service center for technical support Most problems reported are minor and able to be easily solved over the phone In addition free technical support is available and always ready to give advices on application requirements or specific information on the installation and operation of any of our products Please have the following information ready before you call 1 Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages E EAT 2 55 WADE 8156 User s Manual How to Use This Manual This manual is written for the system integrator PC technician and knowledgeable PC end user It describes how to configure your WADE 8156 to meet various operating requirements The user s manual is divided into four chapters with each chapter addressing a basic concept and operation of the server board Chapter 1 Introduction presents what you have inside the box and gives you an overview of the product specifications and basic system architecture for the WADE 8156 board Chapter 2 Hardware Configuration Setting shows the definitions and locations of Jumpers and Connectors so that you can easily configure your system Chapter 3 System Installation describes how to proper
23. ll Gigabit Ethernet Controllers Dual Marvell Gigabit Ethernet 10 100 1000BASE TX controller by PCI Express The WADE 8156 board provide two LED indicators on RJ 45 connectors to show LAN interface status These messages will give you a guide for troubleshooting Yellow LED indicates transmit and receive activity Blinking indicates transmit receive activity On indicates no activity but link is valid Off link is invalid Green LED indicates Link speed On link speed at 1000Mbps On link speed at 100Mbps Off link speed at 10Mbps 3 4 2 Drivers Support WADE 8156 board provide on CD Title to support on board VGA and Ethernet device drivers in various operating systems Before installing the device drivers please see the reference files in each sub directory You cannot install drivers from CD Title directly Intel Q965 Chipset Integrated Graphics supports Win2000 XP Win2003 and 64 bit Windows environment Intel Q965 amp ICH8 R Chipset Driver supports Win2000 XP Win2003 and 64 bit Windows environment Dual Marvell Gigabit Ethernet Controllers support Win2000 XP Win2003 and 64 bit Windows environment 24 55 lp CHAPTER 4 WADE 8156 User s Manual 4 BIOS Setup 4 1 Entering Setup AMI BIOS has a built in setup program that allows users to modify the basic system configuration This information is stored in CMOS RAM whose power is supplied by a battery so that it can retain the setup information even when the power is turn
24. ly mount the CPU main memory and M System Flash disk for a safe installation It will also introduce and show you the driver installation procedure for the Graphics Controller and Ethernet Controller Chapter 4 BIOS Setup Information specifies the meaning of each setup parameter how to get advanced BIOS performance and update to a new BIOS Note 1 Memory type support dual channel interleaved mode assuming DDR2 all DIMMs in a system must be of the same type the speed in all channels is the speed of the slowest DIMM in the system 3 55 1 1 1 2 1 3 1 4 1 5 2 1 2 2 2 3 WADE 8156 User s Manual Table of Content dd F 01 1 y sis AAA Ki Ke Ek Ge Ki ed EA Ge kk Ki ed kk NN ka KAM ke ds N ke die 8 di D 8 Packing Check kiste ee Ke EN Ge ie ee N ee ie Ee N Ge ke EN AT 9 SPECIES 10 System Architecture a asiccssscssceceasnciavensnssscsnscadanancescsisasentedansnadasenssadaientaadawaacwassdade 12 DIMENSIONS 13 Hardware Configuration Setting D 15 Board Eie iii 15 Jumpers amp TE CR 16 Jumpers Connectors Settihnd asses rca GENEE aX de EUR 17 2 3 1 RIG CMOS Cleat Select JE T ma 17 2 3 2 Internal Audio for Chassis AUDIO 17 2 3 8 Audio Connector AUDIO 17 2 39 4 X Auxiliary CPU System Connectors AUX FANI CPU FANI SYS FAN1 17 2 3 5 CD In from CD ROM ED RE RE ee GE eg EE maanani 17 2 3 6 COM1 COM2 Connector COM1 COM 17 2 3 7 GPIO Connector OPIO Di
25. memory module without brand You can also use the single or double side DIMM The three DIMMs can be out of order You can install different size of DDRAM module on DIMM1 DIMM or all to boot up system Without out the contact and lock integrity of memory module with socket it will impact on the system reliability Follow normal procedure to install your DDRAM module into memory socket Before locking make sure that the module has been fully inserted into the DIMM slot Mounting Notch Notch Key r J j ri N Ejector Tab V X X A A NOTE For maintaining system stability do not change any of DDR2 memory parameters in BIOS setup to upgrade your system performance without acquiring technical information 23 55 WADE 8156 User s Manual 3 4 Installing the Mini ITX To install your WADE 8156 board into standard chassis or proprietary environment you need to perform the following steps 1 Check all jumpers setting on proper position 2 Install and configure CPU and memory module on right position 3 Place WADE 8156 board into the dedicated position in your system 4 Attach cables to existing peripheral devices and secure it NOTE Please refer section 3 4 to install display and Ethernet drivers and setup your system WARNING Please ensure that your SBC properly inserted and fixed by mechanism Otherwise the system might be unstable or do not work from bad contact of golden finger 3 4 1 Dual Marve
26. n PCIE High Priority Port Disabled General Help Save and Exit Exit v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 6 2 1 USB Functions This item allows you to active USB ports 4 1 6 2 2 USB 2 0 Controller Select Enabled if your system contains a Universal Serial Bus 2 0 USB 2 0 controller and you have USB peripherals The choice Enabled Disabled 4 1 6 2 3HDA Controller This item allows you to select the chipset family to support High Definition Audio Controller The choice Disabled Enabled 50 55 WADE 8156 User s Manual 4 1 6 2 4 CPU PCI clock Spread Spectrum This feature is used to set the CPU PCI clock Spread Spectrum to be center spread type or down spread type The options are Enabled Disabled 4 1 6 2 5 SLP GAS Min Assertion Width The item allows you to select the assertion width of SLP S44 The choice 4 to 5 sec 3 to 4 sec 2 to 3 sec 1 to 2 sec 4 1 6 2 6 Onboard Giga LAN 1 2 Select Enabled if your system has a LAN device installed on the system board and you wish to use it The choice Enabled Disabled 4 1 6 2 7 PCIE Port 2 3 4 4 1 6 2 8 PCl High Priority Port This item is allows to select PCI high priority port mode 51 55 WADE 8156 User s Manual 4 1 7 X Exit Options BIOS SETUP UTILITY Save Changes and Exit 4 1 7 1 Save Changes and Exit When you have completed the system configuration changes select this option to leave Setup and reboot the compute
27. n 52 Appendix A Watchdog Timer Programming eese 54 Appendix B GPI O Programming i n asus cuni no bh hash dina GE REAGEER ERE b I AA LE a E ERE RV RE ke Ke 55 5 55 Revision History WADE 8156 User s Manual Revision Rev 1 0 Date Apr 2007 Initial released Comment 6 55 lp CHAPTER 1 WADE 8156 User s Manual 1 Introduction 1 1 Description The leading WADE 8156 Mini ITX adopts Intel energy efficient dual core processing to fit a high performance Intel Core 2 Duo Desktop based in the LGA775 package processors and compatible for high end computing applications with PCI E bus architecture to adapt to today s demands and keep complete compatibility with hardware and software designed The onboard devices support one PCI Express x16 slot for flexible expansibility of graphics interfaces integrated graphics and onboard dual Marvell Gigabit Ethernet controllers It s beneficial to build up a high performance and fast transmission availability system for VARs or system integrators The WADE 8156 supports Intel LGA775 Core 2 Duo Desktop processors in E6000 600 500 400 and 300 sequences via Intel Q965 and ICH8 chipset integrated GMA 3000 graphics with DVMT 4 0 display memory up to 256 MB for optional dual display function by VGA LVDS and VGA DVI through optional ADD2 card The board supports two DIMMs up to 4 GB SDRAM with dual channel DDR2 533 667 800 enhan
28. n2 to be an output port iret inportb 0x48F iret iret amp 0x08 set bit3 to O outportb Ox48F iret set pin2 to output low o ci cnm
29. ncy and voltage points to enable power savings If you select Auto you need to set the Power Schemes as Portable Laptop to enable this function This option will be hidden if the current CPU does not support Intel SpeedStep tm tech 4 1 2 1 6Intel C State tech Specific C State supports Standard Conventional C State Enhanced Enhanced C State 29 55 WADE 8156 User s Manual 4 1 2 2 IDE Configuration BIOS SETUP UTILITY Advanced Disabled Compatible Enhanced IDE Configuration Configure SATA 1 as gt Primary IDE Master gt Primary IDE Slave gt Secondary IDE Master gt Secondary IDE Slave gt Third IDE Master gt Fourth IDE Master Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected Hard Disk Write Protect Disabled IDE Detect Time Out Sec 35 ATA PI 80Pin Cable Detection Host Devicel Select Screen Select Item Change Option General Help Save and Exit Exit v02 61 C Copyright 1985 2006 American Megatrends Inc 4 1 2 2 1 SATA 1 Configuration Option Disabled Enhanced 4 1 2 2 2 Configure SATA 1 as Option IDE RAID 4 1 2 2 3 Primary Secondary Third Fourth IDE Master Slave Select one of the hard disk drives to configure it Press lt Enter gt to access the sub menu The options on the sub menu are described in the following sections 4 1 2 2 4Hard Disk Write Protect Set this option to protect the hard disk d
30. ode Set this option to display add on ROM read only memory messages Item Description F Bios Set this value to allow the computer system to force a third party BIOS to display during orce system boot This is the default setting Set this value to allow the computer system to display the information during system boot 4 1 4 1 4 Bootup Num Lock Set this value to allow the Number Lock setting to be modified during boot up 4 1 4 1 5 PS 2 Mouse Support This item allows to set PS 2 Mouse Support function 4 1 4 1 6 Wait For F1 If Error Set this value to allow the Wait for F1 Error setting to be modified Keep Current Item Description This prevents the to wait on an error for user intervention This setting should be used if there is a known reason for a BIOS error to appear An example would be a system administrator must remote boot the system The computer system does not have a E keyboard currently attached If this setting is set the system will continue to boot up in to the operating system If F1 is enabled the system will wait until the BIOS setup is entered Set this value to allow the system BIOS to wait for any error If an error is detected Geen pressing F1 will enter Setup and the BIOS setting can be adjusted to fix the problem This normally happens when upgrading the hardware and not setting the BIOS to recognize it This is the default setting
31. odels will come packaged with a USB 4 port bracket cable The optionally packaged bracket will have two connectors that you can connect to the headers USB1 USB2 The other end bracket containing the USB ports is attached to the computer casing 2 If you are using a USB 2 0 device with Windows 2000 XP you will need to install the USB 2 0 driver from the Microsoft amp website If you are using Service pack 1 or later for Windows XP and using Service pack4 or later for Windows 2000 you will not have to install the driver 2 3 16 VGA Connector VGA1 Description PIN No PIN No Description Green Signal 6 S Ground 8 7 Ground Grund 10 9 v 3 8 bes GLK 19 55 lp CHAPTER 3 WADE 8156 User s Manual 3 System Installation This chapter provides you with instructions on how to setup your system The additional information shows you how to install CPU FAN and memory 3 1 Intel uFC LGA775 Processor 3 1 1 Installing Intel Core 2 Duo Pentium 4 Celeron D CPU e The board comes with a surface mount LGA775 socket designed for the Intel Pentium 4 processor in the 775 land package e Remove the plastic cap to install the uFC LGA 775 Pentium 4 CPU e Unlock the socket by pressing the metal lever sideways to lift it up and open the load plate 1 2 3 4 e Position the CPU above the socket and the gold triangular mark on the CPU must align with pin 1 of the CPU socket Then Insert
32. onnector PWR1 IDE1 Active LED Description PIN No PIN No Description PINNo Signal Description 3 3V 13 1 3 3V 5V Pull up for HDD LED HDD actives LED cathode terminal P LED ES Sale Ground PIN No SignaliDescripion Ground 18 6 2 5V Pull up for Power LED Ground 20 8 PWOK System Reset Ca 9 sve PINNo Signal Description System Power On Switch PINNo Signal Description cec Power button control signal ae Dong 2 3 11 4 pin ATX Power Connector PWR2 2 3 12 Serial ATA 1 2 3 4 Connectors SATA1 SATA2 SATA3 SATA4 PINNo Description These SATA connectors support Serial ATA 300 Each SATA connector can only support one serial ATA device Note With most storage devices there is a power cable that you need attach to a power source power supply Ground 18 55 WADE 8156 User s Manual 2 3 13 Internal Speaker Connector SPK1 2 3 14 LAN 1 2 amp USB 1 2 3 4 Connectors USB2LAN1 USB2LAN2 LAN 1 2 SPK Active SPK Active USB 1 2 3 4 PIN No Description PIN No Description 5 V fused 5 V fused USBPO 3 6 USBP1 2 USBP0 3 USBP1 2 Ground 8 Ground 2 3 15 Internal USB 5 6 7 8 Connectors USB1 USB2 Note 1 This mainboard provides 4 USB headers on the board allowing for 4 additional USB ports To make use of these headers you must attach a USB bracket cable with USB ports some m
33. r so the new system configuration parameters can take effect 4 1 7 2 Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration 4 1 7 3 Discard Changes Select Discard Changes from the Exit menu and press lt Enter gt 4 1 7 4 Load Optimal Defaults Load Optimal Default values for all the setup questions F9 key can be used for this operation 4 1 7 5 Load Failsafe Defaults Load Failsafe Default values for all the setup questions F8 key can be used for this operation 52 55 lp Appendix WADE 8156 User s Manual Appendix A Watchdog Timer Programming The Watchdog Timer WDT is a special hardware device that monitors the computer system during normal operation The WDT has a clock circuit that times down from a set number to zero If a monitored item occurs before that timer reaches zero the WDT resets and counts down again If for some reason the monitored item doesn t occur before the timer reaches zero the WDT performs an action such as a diagnostic operation rebooting the computer or generate an NMI Watchdog Configuration Address Port 2Eh Data Port 2Fh Description 87h na Enter Key 87h na Enter Key 07h 08h Setup Watch Dog Function 2Dh 20h Setup Watch Dog Function 30h 01h Enable Watch Dog Function F5h 00h 00h select second mode 08h select minute mode E Di Time out occurs after 0 255 second minute 00h Time out
34. rive from being overwritten The Optimal and Fail Safe default setting is Disabled 4 1 2 2 5 IDE Detect Time Out Sec Set this option to stop the AMIBIOS from searching for IDE devices within the specified number of seconds Basically this allows you to fine tune the settings to allow for faster boot times Adjust this setting until a suitable timing that can detect all IDE disk drives attached is found The options 0 5 10 15 20 25 30 35 sec 30 55 WADE 8156 User s Manual 4 1 2 2 6 ATA PI 80Pin Cable Detection Set this option to select the method used to detect the ATA PI 80 pin cable The Optimal and Fail Safe setting is Host amp Device Item Description Set this value to use both the motherboard onboard IDE controller and IDE disk drive to detect the Host amp Device type of IDE cable used This is the default setting Host Set this value to use motherboard onboard IDE controller to detect the type of IDE cable used Device Set this value to use IDE disk drive to detect the type of IDE cable used 31 55 WADE 8156 User s Manual 4 1 2 3 Super IO Configuration BIOS SETUP UTILITY OnBoard Floppy Controller Enabled 32 55 WADE 8156 User s Manual 4 1 2 3 1 Serial Port1 2 Address This option specifies the base UO port address and Interrupt Request address of serial port 1 2 The Optimal setting is 3F8 IRQ4 The Fail Safe default setting is Disabled Item Description S
35. scs bi 18 2 3 8 PS 2 Keyboard Mouse KBMS1 sesse ees ee ee ee ee RR ee ee ee ee ee 18 2 3 9 Front Side Indicators PANELI suscitan RE ge EE ki 18 2 3 10 24 pin ATX Power Connector DWRI ee Re ee ee ee 18 2 3 11 4 pin ATX Power Connector DW 18 2 3 12 Serial ATA 1 2 3 4 Connectors SATA1 SATA2 SATA3 SATA4 18 2 3 13 Internal Speaker Connector SPK1 EEN 19 2 3 14 LAN 1 2 amp USB 1 2 3 4 Connectors USB2LAN1 USB2LAN 19 2 3 15 Internal USB 5 6 7 8 Connectors USB1 UP 19 2 3 16 VGA Connector VGA essa 19 4 55 WADE 8156 User s Manual 3 Syslem A Ee es GE Ne N gs N eg Ge Ee NN eN de Ee 21 3 1 Intel UFC LGA775 Processor erre ee ee nennen nenne natn natn narran sa ee ee 21 3 1 1 Installing Intel Core 2 Duo Pentium 4 Celeron D CPU 21 3 2 Installing 1 U Cooler for Intel uFC LGA775 Processor 22 3 3 Main Memory s sisien ee 23 3 4 Installing INA MIA ica 24 34 1 Dual Marvell Gigabit Ethernet Controllers seeeeseeesssessssss 24 3 4 2 Drivers Support ER 24 LE BIS li 26 4 1 Entering SOU uc RAK NE KEN NEER DAN NN AAK ENS GN Ek Ned N ke dd 26 4 1 1 Main LE OG RTT 26 4 1 2 Advanced Setting ctas derer a 27 41 3 Advanced PCI PnP Salig lia 41 KIA BOGE EE 44 4 1 5 Security Settings EE 46 4 1 6 Advanced Chipset Settings ENEE 47 Ai EILOBUORS ot ee tre
36. sed by ISA devices The options Disabled 16K 32K 64K 43 55 WADE 8156 User s Manual 4 1 4 Boot Settings BIOS SETUP UTILITY Main Aduanced PCIPnP Boot Security Chipset Exit Boot Settings Configure Settings during System Boot e Select Screen TL Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02 61 OCopuright 1985 2006 American Megatrends Inc 4 1 4 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Boot Settings Configuration Allows BIOS to skip E certain tests while booting This will Quiet Boot Disabled decrease the time AddOn ROM Display Mode Force BIOS needed to boot the Bootup Num Lock On system PS 2 Mouse Support Auto Wait For F1 If Error Enabled Hit DEL Message Display Enabled Interrupt 19 Capture Disabled Select Screen Select Item Change Option General Help Save and Exit Exit v02 61 C Copuright 1985 2006 American Megatrends Inc 4 1 4 1 1 Quick Boot The Optimal and Fail Safe default setting is Disabled Allow to set this value to allow the BIOS to skip certain POST tests to boot faster or disabled to perform all POST tests 44 55 WADE 8156 User s Manual 4 1 4 1 2 Quiet Boot Set this value to allow the boot up screen options to be modified between POST messages or OEM logo The Optimal and Fail Safe default setting is Enabled 4 1 4 1 3 AddOn ROM Display M
Download Pdf Manuals
Related Search