English manual
Contents
1. 1 Safety precautions 1 2 Main features 2 3 Front panel and functions 2 4 Main menu operation description 3 4 1 Satellite 3 4 1 1 Find satellite 4 4 1 2 List satellite 5 6 4 1 3 Display spectrum 6 7 4 1 4 Edit satellite 7 10 4 1 5 Edit transponder 10 12 4 1 6 Tools 12 14 4 2 Terrestrial 15 4 2 1 Check Channel 15 4 2 2 Analyze Spectrum 16 4 2 3 List Channel 16 17 4 2 4 Define User Data 17 18 4 2 5 Select Parameter 19 4 3 Setup 19 4 3 1 Control Buzzer 19 4 3 2 Backup Data 19 4 3 3 Upgrade Data 19 21 5 Update application system 21 6 Technique specifications 22 7 Attachments 22 8 Connection diagram 23 Cautions Satellite receiver must have minimum 750mA LNB power output otherwise connect LNB after satellite finder power on2. Select a transponder Move To drive the motor to rotate dish antenna press LEFT or RIGHT to select east or west press OK once will rotate one step press and hold will rotate continuously Goto To rotate to the target automatically press LEFT or RIGHT to select XX or ZERO When select XX and press OK the motor will rotate dish antenna to corresponding satellite automatically When select ZERO and press OK will rotate to 0 scale Note Before use Goto function it is need to input local longitude and latitude in Calculate Angle submenu Set Limit To set rotation limit press LEFT or RIGHT to select east west or clear limit E g rotate motor to an east direction angle then select EAST and press OK this angle location will be EAST rotation limit motor will not be able to rotate over this east limit Select CLEAR to cancel limit 15 1 Press UP or DOWN to move to the numeric parameter and press OK to enter press LEFT or RIGHT to select digit position then press UP or DOWN to set the digit press EXIT to exit current setting 2 The letter E W N and S means east longitude west longitude north hemisphere and south hemisphere respectively When move to the letter it can be set by press LEFT or RIGHT 3 The angle data can be calculated and displayed automatically when parameter is being set Elevation angle is counted from horizon upward azimuth angle is from north clockwise 4
3. feedhorn position and polarizing angle so that help the best dish installation Brief introduction Attention 4 Main menu operation description When power on the screen will display some information about software then enter to the main menu 1 Press UP DOWN LEFT or RIGHT to select submenu press OK to enter 4 1 Satellite This menu shows user all the satellite information satellite para meters signal strength and quality Satellites a r e s h o w n i n l i s t m a k e s u s e r t o v i e w a n d o p e r a t e conveniently List satellite As below 4 1 2 List satellite Function S e l e c t S a t e l l i t e 01 APSAT 5 11300 02 ST 2 05150 03 MEASAT 3 3 05150 04 CHINASAT 9 11300 05 NSS 6 11300 06 Sat01 05150 07 Sat02 Univ 6 S e l e c t T ra n s p o n d e r 01 12630 H 43200 02 12537 V 41250 03 12720 V 41250 1 Press UP or DOWN to select the desired satellite press OK to show transponder frequency contained in this satellite As below 2 Press UP or DOWN to select the desired frequency press LEFT or RIGHT to turn page press OK to show the satellite name frequency signal intensity and quality As below A P S A T 5 0 1 1 2 6 3 0 H 4 3 2 0 0 T Y P E D V B S 2 F E C 8 P S K 2 3 C N 8 4 0 B E R 0 1 5 E 5 S Q 6 3 4 2 When the signal is locked it will show current signal type FEC C N and BER Press UP or DOWN to change satellite Pre
4. Press EXIT button to exit the menu 20 2014 9 2 13 50 29 sf560 01 01 00CHina 6B 05150 0 0 0 115 5 0 001 001 01 03951 09520 1 001 002 01 03880 27500 0 01 02 Koreasat 5 11300 1 0 0 113 0 0 001 003 02 12647 28000 1 01 03 0000NSS 11 Univ 0 0 0 108 2 0 001 004 03 12537 41250 1 01 01 00China 6B 05150 0 0 0 115 5 0 1 2 3 4 5 6 7 8 9 01 means this line information is about satellite The serial number of the satellite it must be continuous can not from 01 to 03 Satellite name The length is ten If the name of the satellite is sat01 the third must be 00000sat01 The LO Freq of the satellite Represent 22KHz signal status 0 means OFF 1 means ON Represent DiSEqC1 0 status 0 means OFF 1 means LNB1 2 means LNB2 3 means LNB3 4 means LNB4 Represent USALS status 0 means USALS OFF 1 means USALS ON Satellite Longitude Satellite location 0 means east 1 means west 21 1 2 3 4 5 6 001 001 01 03951 09520 1 001 means this line information is about TP The serial number of the TP it must be continuous can not from 01 to 03 The number means this TP is belong to which satellite have the same number Transponder frequency Symbol Rate Polarity 0 means H 1 means V 5 Update application system The product can update application system from USB port if you want to update application system insert U disk press MENU and con
5. select a existing satellite Tran Freq Set up the transponder frequency press OK to enter edit mode then use LEFT RIGHT UP DOWN to set the digit EXIT to exit the setup of the item Symbol Rate Symbol rate of current transponder Set up method as shown above Polarity Vertical or Horizontal polarization When complete adding transponder press EXIT to exit the menu and operate according to the prompts As below Press ok to SAVE others to EXIT 12 2 Modify Transponder Press OK on Modify Transponder to enter the item As below S e l e c t S a t e l l i t e 01 APSAT 5 11300 02 ST 2 05150 03 MEASAT 3 3 05150 04 CHINASAT 9 11300 05 NSS 6 11300 06 Sat01 05150 07 Sat01 Univ Use UP DOWN LEFT RIGHT to move cursor to a satellite then press OK to enter the transponder edit screen M o d i f y T r a n s p o n d e r 0 1 S a t e l l i t e APSTAR 2R Tran Freq 03629 Symbol Rate 01489 Polarity H When complete modifying transponder press EXIT to exit the menu and operate according to the prompts As below D a t a c h a n g e d P r e s s o k t o S A V E o t h e r s t o E X I T 13 1 USALS operation Sat Name Sat Long 180 0 Sat L a t i E AST Trans 03840 H 27500 Move WEST Goto XY Set Limit EAST S 17 Q 0 Sat03 Sat Select a satellite the satellite s USALS must be set to ON Sat Long Satellite longitude Sat Dir Satellite direction Trans
6. that contained in the Define User Data or selected country change it in Check Channel menu Press LEFT or RIGHT to move cursor slowly press UP or DOWN to move quickly current frequency and signal strength are shown on the top 4 2 3 List Channel The function can show all channels by country It offers the convenience of check and operation S e l e c t C o u n t r y 0 2 N e t h e r l a n d s 0 3 S e r b i a 0 4 G e r m a n y 0 5 B e l g i u m 0 6 H u n g a r y 0 7 D a n m a r k 0 1 E n g l a n d 17 1 Press UP or DOWN button to move cursor press LEFT or RIGHT button to change page press OK to enter the channel list of the selected country as following N o C h a n n e l F r e q B W 0 2 C H 2 2 4 8 2 0 8 0 3 C H 2 3 4 9 0 0 8 0 4 C H 2 4 4 9 8 0 8 0 5 C H 2 5 5 0 6 0 8 0 6 C H 2 6 5 1 4 0 8 0 7 C H 2 7 5 2 2 0 8 0 1 C H 2 1 4 7 4 0 8 4 2 4 Define User Data Function In this menu user can add modify or delete channels Operation Enter the Define User Data menu As following S u b m e n u M o d i f y C h a n n e l D e l e t e C h a n n e l A d d C h a n n e l 18 1 Select the desired function and enter In the Add Channel and Modify Channel function user can modify channel name frequency and bandwidth Add Channel C h a n n e l Name Freq KHz 730000 BW MHz 8 CH34 Modify Channel C h a n n e l Name Freq KHz 5 30000 BW MHz 8 BH31 The d
7. SF 560 95 150mm 128g USER S MANUAL 1 3 5 Please read this user s guide carefully especially for the first time users Do not touch the LCD display by hand Do not place heavy items on the device Keep this unit away from the heat direct sunlight strong mechanical vibration or dusty places Clean the surface with a dry and soft cloth Do not pour any liquid to void serious injury Keep the unit in a ventilated place Please contact your supplier if any failure occurs Operate properly per this user s guide otherwise any damage of the unit is at the user s risk Specifications are subject to change and improvement without notice Please inquire of manufacturer if there s any need after the usage 1 The unit is powered by external power supply or receiver 2 Before connection is confirmed keep equipment power off 3 If short circuit happens when connecting cable the screen will show satellite signal input short circuit or Terrestrial signal input short circuit Please power off please check and remove the problem 1 Safety precautions Table of Contents This type of digital satellite finder is a simple and convenient instrument to install and adjust satellite dish As digital satellite finder it is necessary to input corresponding satellite parameters such as LO frequency of LNB Down Frequency symbol rate etc It can be used as an indicator to adjust satellite dish
8. ata will save when user finish editing and press EXIT N o C h a n n e l F r e q B W 0 1 C H 3 2 7 3 0 0 0 0 8 0 2 C H 3 3 7 3 0 0 0 0 8 0 3 C H 3 4 7 3 0 0 0 0 8 In the Delete Channel menu use UP DOWN LEFT RIGHT to select a channel press OK to delete the selected channel press EXIT to exit 19 4 2 5 Select Parameter In this menu user can turn on or turn off the 5V output power for terrestrial antenna and select country S e l e c t P a r a m e t e r 5 V O u t p u t C o u n t r y R u s s i a O N 4 3 Setup In this menu user can set buzzer and manage user data S e t u p C o n t r o l B u z z e r 4 3 1 Control Buzzer Set the buzzer to on or off state 4 3 2 Backup Data You can back up satellite data to U disk by this menu 4 3 3 Update Data You can update satellite data from U disk by this menu Note Only the txt format file which named sf560 can be identified and must write as below There is a blank line at last Frequency range Signal Level Demodulation Scheme Bandwidth 78 10dBm DVB T QPSK 16QAM 64QAM DVB T2 16QAM 64QAM 256QAM 6MHz 7MHz 8MHz 170 230MHz VHF 470 862MHz UHF 75 Impedance S2 T2 Antenna Antenna 2 2 Main features Edit transponder down frequency LO frequency of LNB symbol rate etc Find satellite signal and antenna signal accurately and simply Provide spectrum display Suppor
9. clearly by selecting corresponding parameters in this menu 4 1 3 Display Spectrum Function D i S E q C 1 0 L N B 4 S e l e c t P a r a m e t e r P o l a r i t y V 2 2 K O F F Operation or This function let you to delete the existing transponders that you want to delete 3 Delete Transponder 4 1 6 Tools Tools USALS Operation Angle Caiculation M a i n M e n u T e r r e s t r i a l Satellite Find Satellite This menu is about operation of satellite 4 4 2 Terrestrial This menu is about operation of Terrestrial signal T e r r e s t r i a l C h e c k C h a n n e l 4 2 1 Check Channel Function It provides the users quick search for terrestrial signal signal strength and quality display parameters setting Operation C o u n t r y C h a n n e l C h 3 2 F r e q K H z 7 3 0 0 0 0 B W M H z 8 L O C K D V B T 2 S 4 6 Q 7 3 U s e r D e f i n e Move cursor to Country use LEFT or RIGHT to change between user defined data or the country that s e l e c t e d i n S e l e c t P a r a m e t e r m e n u I f s e l e c t User Define user can input desired frequency and select different BW number 6 8 Move to Channel to select a channel Press EXIT to exit current menu 16 4 2 2 Analyze Spectrum The function shows the terrestrial signal spectrum 730 0MHz 47 S F This diagram displays the signal strength of the channel
10. e according to the prompts As below Press ok to SAVE others to EXIT Move cursor to Modify Satellite and press OK then you can enter the Modify Satellite interface As below 2 Modify Satellite Modify Satellite 01 Name LO Freq 05150 22K OFF DiSEqC1 0 OFF USALS OFF Longitude 076 5 E APSTAR 2R 10 Press UP or DOWN to select different modify item then press LEFT or RIGHT to change setting of selected item If need to modify satellite name or digit of selected parameter press OK to enter press LEFT or RIGHT to select character or digit position then press UP or DOWN to modify press EXIT to exit the item after modify When modify satellite completed press EXIT to exit the menu and operate according to the prompts As below Data changed Press OK to SAVE others to EXIT If need to delete satellite enter Delete Satellite item press UP or DOWN to select the satellite you want to delete and press OK to confirm then press OK to delete the satellite or press others key to exit User can add modify or delete transponders in this menu 3 Delete Satellite 4 1 5 Edit transponder Edit Transponder Add Transponder Modify Transponder Delete Transponder 11 1 Add Transponder Press OK on Add Transponder to enter the item As below Add Transponder Satellite Tran Freq 03980 Symbol Rate 27500 Polarity H APSTAR 2R Satellite Press LEFT or RIGHT to
11. nect power supply until the screen display as below Select File 01 SF550 1 BIN Press OK to update When the system is complete updating the system will restart 22 6 Technique specifications 950 2150MHz 65 25dBm 75 1Msps 60Msps DVB S QPSK DVB S2 8PSK 16APSK 32APSK Supported Supported Supported AC110 240V 50Hz 60Hz 18V DC 1000mA F type Supported 10 50 Frequency range Signal Level Impedance Symbol rate Demodulation 22KHz Tone DiSEqC1 0 USALS Switching Power input Switching Power output Connector USB port Operation temperature Power supply Others Power supply x 1 Instruction Manual x 1 F type connector x 1 F to TV connector x 2 7 Attachments 14 The function can calculate antenna elevation azimuth and LNB polarization angle according to satellite longitude local location longitude and latitude parameter settings it is useful for receiving installation 2 Angle Calculation P a r a m e t e r S e t t i n g S a t L o n g 1 1 5 5 E L o c a l L o n g 1 1 3 3 E L o c a l L a t 2 2 2 N A n g l e C a l c u l a t e d E l e v a t i o n 6 3 8 A z i m u t h 1 7 4 1 P o l a r i z a t i o n 5 3 23 8 Connection diagram Diagram1 LNB SAT Receiver Diagram2 Connection optional Power supply LNB 1 2 3 4 5 6 Operation User can see signal spectrum
12. ss LEFT or RIGHT to change transponder 3 Press EXIT to exit the current menu 7 1 Press UP or DOWN to select different item then press LEFT or RIGHT to change setting of selected item 2 After selecting the appropriate parameters press OK to enter spectrum display 1 5 5 0 M H z 7 6 d B u V 3 Press LEFT or RIGHT to move cursor slowly press UP or DOWN to move quickly current frequency and signal strength are shown on the top 4 Press EXIT to exit the current menu 4 1 4 Edit satellite User can add modify or delete satellites in this menu and set up satellite name LO frequency 22KHz DiSEqC1 0 USALS and satellite longitude according to self requirements E d i t S a t e l l i t e A d d S a t e l l i t e M o d i f y S a t e l l i t e D e l e t e S a t e l l i t e 1 Add Satellite Move cursor to Add Satellite and press OK then you can enter the Add Satellite interface As below A d d s a t e l l i t e Name LO Freq 05150 22K OFF DiSEqC1 0 OFF USALS OFF Longitude 180 0 E Sat01 8 9 Press UP or DOWN to select different setting item then press LEFT or RIGHT to change setting of selected item If need to input satellite name or digit of select parameter press OK to enter press LEFT or RIGHT to select character or digit position then press UP or DOWN to modify press EXIT to exit the item after setting When adding satellite completed press EXIT to exit the menu and operat
13. t 0 22KHz Support DISEqC1 0 switch Support USALS Support 0 5V Update data through USB Use LCD to display the satellite signal and antenna signal strength and quality Support DVB S DVB S2 DVB T and DVB T2 1 2 3 4 5 6 7 8 9 10 11 12 14 13 15 16 1 SAT Signal Input 2 LCD display 3 Compass 4 DC input 5 Power indicator 6 13V 18V indicator 7 0 22K indicator 8 Signal locked indicator 9 Menu 10 EXIT 11 UP 12 DOWN 3 Front panel introduction and function description 13 LEFT 14 RIGHT 15 OK 16 USB port 17 ANT Signal Input 17 1 Press UP or DOWN to select different setting item then press LEFT or RIGHT to change setting of selected item 2 If need to input digit of selected parameter press OK to enter press LEFT or RIGHT to select digit position then press UP or DOWN to modify the digit of parameter press EXIT to exit the item after setting 3 When parameter settings are confirmed and signal is ready signal level and quality S Q will display correspond ing value otherwise adjust antenna dish to get the highest signal level and quality readings 4 Press EXIT to exit the current menu It provides the users quick search for satellite signal signal strength and quality display parameters setting Operation 4 1 1 Find Satellite Function SAT 01 113 00 TP 06 12630 H 43200 LOCK S Q 62 42 Connection optional
Download Pdf Manuals
Related Search