- Océ
Contents
1. Equipment VCCI If this equipment is used in a domestic environment radio disturbance may occur in which case the user may be required to take corrective action Mercury All Countries At the end of the equipment s service life the mercury containing fluorescent lamp must be removed from the equipment and treated separately according Directive 2002 96 EC Waste Electrical and Electronic Equipment Dispose of in accordance with all federal state and local regulations The European Waste Catalogue EWO number of the mer cury containing fluorescent lamp is 20 01 12 Battery labeling EU only This product contains Button Cells They are located in printed circuit board that are essential for the continuous error free functioning of the product The button cells should be removed only by skilled service technicians who are aware of the removal instructions provided by Oc Technologies B V 12 Chapter 2 Regulation notices Regulation notices country dependent X Button cell specification Button cell location Button cellca Containing the following sub pacity stances if applicable Control board MOTHER 3 0V CR2032 Lithium type BOARD CELERON 2GHZ Ibase MAINBOARD MB896 Lithium type Caution Oc does not accept any liability for any damage or consequences if the batteries are removed by persons other than Oc service personnel End of Service Life WEEE EU Only x The crossed out trash can symbol2. important information with regard to the user safety and the prevention of equipment problems Make sure that you observe the safety rules hereinafter This helps to assure that you can work with the product safely Make sure that you observe all the precautions mentioned below Note Some parts of the contents of this section may not be applicable to your product Note Please refer to the corresponding Safety Data Sheets for specific safety information You can download the Safety Data Sheets from the support site of your product at http global oce com support Warning and Caution Symbols A A D Caution Ignoring this warning could cause serious injury or even death Attention Ignoring this warning could cause injury or damage to property Note Indicates additional important information The indicators above are used on the warning labels or in the manuals to categorize the level of safety warnings Disassembly and Modification 6 Warning Chapter 1 Safety information Instructions for safe use m Do not remove covers and panels that are fixed to the machine Some machines have a high voltage component or a laser beam source inside that could cause an electric shock or blindness m Do not modify this machine since this could cause fire electric shock or breakdown If the machine contains a laser the laser beam source could cause blindness Caution m Do not carry out maintenance activities on comp
3. indicates that at the end of its service life the equip ment must be collected separately in the EU Member States The black bar specifies that the appliance is put on the market after August 13 2005 Reference Directive 2002 96 EC Contact your local Oc organization for further information RoHS China Only The Environmental Protection Use Period EPUP applicable for the printing system for delivery to the People s Republic of China is 20 years This EPUP which does not include consumables or expendables does not affect any warranty that is provided for the system and may not be construed or interpreted as a separate warranty for the printing system ENERGY STAR All countries Oc Technologies B V has joined the ENERGY STAR Program of the United States Environmental Protection Agency EPA The purpose of the ENERGY STAR Program is to promote the manufacturing and marketing of energy efficient equipment thereby potentially reducing combustion related pollution Using the energy management features outlined below prevents unnecessary power consumption which helps to prevent air pollution from electricity generating plants and saves money on your utility bills As an Chapter 2 Regulation notices 13 Regulation notices country dependent ENERGY STAR Partner Oc Technologies B V has determined that the Oc Color Wave 300 meets the ENERGY STAR criteria for energy efficiency laid down in the ENERGY STAR Program Requir
4. 8 Canada http www oce ca Oc Office Equipment Shanghai First Shanghai Center Phase II Building 4 Lane 180 Zhangheng Road Pudong District Shanghai 201204 P R China http www oce com cn Oc Czech Republic ltd Babick 2329 2 149 00 Praha 4 Oc Danmark a s Vallensb kvej 45 2605 Brondby http www oce fi 20 Chapter 4 Miscellaneous Czech Republic Denmark http www oce cz http www oce dk Oc Finland OY Oc France S A Niittyrinne 7 32 Avenue du Pav Neuf 02270 Espoo 93882 Noisy le grand Cedex Finland France http www oce fr Addresses of local Oc organisations Oc Deutschland GmbH Solinger Stra e 5 7 45481 M lheim Ruhr Germany http www oce de Oc Hungaria Kft H 1241 Budapest Pf 237 Hungary http www oce hu Oc Italia S p A Strada Padana Superiore 2 B 20063 Cernusco sul Naviglio MI Italia http www oce it Oc Belgium S A Rue Astrid 2 A 1143 Luxembourg Belair http www oce lu Oc Hong Kong and China head office Room 3711 18 Tower 1 Millennium City 1 388 Kwun Tong Road Kwun Tong Kowloon Hong Kong http www oce com hk Oc Ireland Ltd 3006 Lake Drive Citywest Business Campus Saggart Co Dublin Ireland http www oce ie Oc Japan Corporation 3 25 1 Nishi Shinbashi Minato Ku Tokyo 105 0003 Japan http www ocejapan co jp Oc Malaysia Sdn Bhd 3 01 Level 3 Wisma Academy Lot 4A J
5. Oc ColorWave 300 User manual Safety information Copyright 2009 Oc All rights reserved No part of this work may be reproduced copied adapted or transmitted in any form or by any means without written permission from Oc Oc makes no representation or warranties with respect to the contents hereof and specifi cally disclaims any implied warranties of merchantability or fitness for any particular purpose Further Oc reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes Edition 2009 10 Contents Contents Chapter 1 Safety information iaia 5 Instructions for safe USE ii 6 Chapter 2 Regulation notices uiiia iii 11 Regulation notices country dependent ii 12 Chapter 3 General information iii 17 Caution labels and notations sasen eanan anana na anana anana nenen a nana 18 Chapter 4 TEE TEE 19 Addresses of local Oc organisations esses 20 Contents Chapter 1 Safety information Instructions for safe use Instructions for safe use Introduction H H All the products have been tested in accordance with the strictest international safety standards Please read the following sections before you connect the machine to the power supply These sections contain
6. alan 19 1 46300 Petalig Jaya Selangor Darul Ehsan Malaysia http www ocemal com my Oc Mexico S A de CN Prolongaci n Reforma 1236 4to Piso Col Santa F Del Cuajimalpa C P 05348 M xico D F M xico http www oceusa com Oc Norge A S Postboks 4434 Nydalen Gjerdrums vei 8 0403 Oslo Norway http www oce no Chapter 4 Miscellaneous 21 Addresses of local Oc organisations D 22 Oc Poland Ltd Sp z 0 0 ul Bitwy Warszawskiej 1920 r nr 7 02 366 Warszawa Poland http www oce com pl Oc Singapore Pte Ltd 21 Ubi Road 1 05 01 Brilliant Building Oc Portugal Equipamentos Gr ficos S A Av Jos Gomes Ferreira 11 Piso 2 Mi raflores 1497 139 Alg s Portugal http www oce pt http www oce es Singapore408724 Oc Espafia SA Oc Svenska AB Business Park Mas Blau Sollentunavagen 84 Osona 2 08820 El Prat de Llobregat 191 27 Sollentuna Barcelona Sweden Spain http www oce se Oc Schweiz AG S gereistrasse 10 CH8152 Glattbrugg Schweiz http www oce ch Oc Nederland B V P O Box 800 5201 AV s Hertogenbosch The Netherlands http www oce nl Oc North America Inc 100 Oakview Drive Trumbull CT 06611 USA http www oceusa com Oc Thailand Ltd B B Building 16 Floor 54 Asoke Road Sukhumvit 21 Bangkok 10110 Thailand Oc UK Limited Oc House Chatham Way Brentwood Essex CM14 4DZ United Kingdom htt
7. ation is damaged please contact your service representative Note Li In order to limit energy consumption during times of non use the Oc ColorWave 300 has a Sleep mode during which the power level is reduced The value for the Sleep mode is listed in the Product Safety Data Sheet Space Requirements and Operating Precautions Power Supply Please refer to the corresponding Safety Data Sheets for specific safety information You can download the Safety Data Sheets from the support site relevant to your product at http global oce com support Operating environment The environmental requirements for correct operation of the machine are as follows m Operating temperature T 15 C 59 F to 30 C 86 F m Relative Humidity RH 20 to 80 96 18 Chapter 3 General information Chapter A Miscellaneous Addresses of local Oc organisations Addresses of local Oc organisations Oc Australia Ltd P O Box 363 Ferntree Gully MDC Vic 3165 Australia http www oce com au Oc Belgium N V S A J Bordetlaan 32 1140 Brussel Belgium http www oce be Oc Osterreich GmbH Postfach 95 1233 Vienna Wienerbergstrasse 11 Vienna Twin Tower 1100 Vienna Austria http www oce at Oc Brasil Com rcio e Ind stria Ltda Av das Nag es Unidas 11 857 Brooklin Novo S o Paulo SP 04578 000 Brasil http www oce brasil com br Oc Canada Inc 4711 Yonge Street Suite 1100 Toronto Ontario M2N 6K
8. ements for Imaging Equipment Version 1 1 D ENERGY STAR Energy consumption All countries In order to limit energy consumption during times of non use the Oc ColorWave 300 has a Sleep mode during which the power level is reduced The value for the Sleep mode is listed in the Product Safety Data Sheet Power modes and delay times The energy consumption and efficiency are influenced both by the product technology and by the settings chosen by the user especially the delay times that are selected to enter reduced power states The following delay times have been pre set Power modes and delay times Operational mode Default delay time minutes Low power s minutes range 5 240 minutes Sleep 30 minutes range 5 240 minutes The modes above are automatically entered after the Default Delay Time has elapsed counting from the moment the last print has been produced These settings are recom mended and for most users ensure both ease of use and low energy consumption Between brackets are the minimum and maximum values the Delay Times can be changed to by the key operator Shorter delay times within this range will lower the energy consumption even further but may cause longer recovery times In some cases longer delay times may prove to be more convenient but it should be noted that this may cause an increase in energy consumption Therefore from an energy preservation point of view longer delay times are not recomm
9. emits smoke or produces unusual odors or noises Immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative Caution m Stop using the machine if the machine was dropped or a cover was damaged Imme diately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative 8 Chapter 1 Safety information Instructions for safe use m LCD display Do not rub press or touch the display surface with hard material because the polarizer at the surface can be easily scratched The LCD module consists of glass Therefore the LCD module can damage when you drop pinch strongly or punch the module When glass breaks be careful that you do not get injured by glass pieces Call Customer Service Consumables supplies and maintenance materials Warning m Do not throw ink containing or contaminated parts into an open flame Caution m Donot leave ink containing or contaminated parts in a place within reach of children m Always use the materials which the manufacturer recommended and which are devel oped for this machine Materials not approved by the manufacturer may result in faults in your machine Moving the Machine Caution m Make sure that you disconnect the power cord and other cables before you move the machine m Make sure that you check the documentation for the space requirements before
10. ended Standby Power Federal Energy Management Program All Countries 14 This product meets the following criteria for the United States Federal Energy Management Program FEMP m In standby mode this product consumes less than 1 W o W After shutting down all systems properly standby mode as defined by FEMP is reached by switching the main switch to o m This product has a hard off switch m This product meets the Energy Star guidelines for energy efficiency Chapter 2 Regulation notices Regulation notices country dependent Recycled paper All countries The use of recycled paper benefits the environment The Oc ColorWave 300 is designed to use recycled paper which complies with the requirements of EN12281 2002 Product literature on recommended types of recycled copier paper can be obtained from your local Oc company or Oc Headquarters Chapter 2 Regulation notices 15 Regulation notices country dependent 16 Chapter 2 Regulation notices Chapter 3 General information Caution labels and notations Caution labels and notations Introduction You can find the power marking label near the mains entrance If connection to a different mains voltage is required contact Customer Service Caution A Do not remove caution labels or caution notations Ifa label or notation is soiled please clean the label or notation If you cannot make label or notation legible or if the label or not
11. nected via a wall socket Place the machine close to a wall socket that is easily accessible The power plug is intended to serve as a disconnect device Grounding Warning m Connect the power cord to an electrical outlet wall socket that is equipped with a grounding terminal Installation Warning m Make sure that the machine is placed on a level horizontal surface of sufficient strength Do not place this machine on an unstable or tilted bench Do not place this machine in a location that is subject to lots of vibrations and shocks Do not use flammable sprays liquids or gases near this product because this could cause a fire Ventilation Caution m The machine can produce odors of exhaust air when you use this machine in a poorly ventilated room for a long time produce large amounts of copies or print Therefore make sure that you ventilate this room well Do not block the ventilation openings of the machine m Do not place the machine in rooms which are too small and insufficiently ventilated See the Product Safety Data Sheet of the machine for the ventilation requirements Actions in response to troubles Warning m When a piece of metal water or any other similar foreign matter gets inside the ma chine immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative m Immediately stop using the machine if the machine becomes excessively hot
12. onents and maintenance materials other than the components and materials that are mentioned in the user manual Do not place any liquids on the machine Do not open any door while the machine starts up or runs unless the operator panel displays a message asking you to open one or more doors Only use maintenance materials or other materials for their intended purpose To avoid any risk only properly qualified and trained service technicians are allowed to modify the machine m Do not bridge any mechanical or electrical circuit breakers Note m Keep maintenance materials away from children Power cord Warning m Do not scratch abrade heat twist bend place a heavy object on or cause any other damage to the power cord The use of a damaged power cord exposed core wire broken wire for example could result in a fire or breakdown If you find any of these conditions immediately turn OFF the power switch and unplug the power cord from the power outlet Then call your authorized service representative m Only use the mains connector cable that was supplied with the machine Power source Warning m Do not connect the machine to a mains voltage that differs from the value as stated on the power marking label Note m Ifconnection to a different mains voltage is required contact your authorized service representative Power plug Warning Chapter 1 Safety information 7 Instructions for safe use m For machines that are con
13. p www oce co uk Note The web site http www oce com gives the current addresses of the local Oc organiza tions and distributors Chapter 4 Miscellaneous Addresses of local Oc organisations Note The addresses of local Oc organizations for information about the Wide Format Printing Systems and the Production Printing Systems can be different from the addresses above Refer to the web site http www oce com for the addresses you need Chapter 4 Miscellaneous 23 Beyond the Ordinary 22009 Oc Illustrations and specifications do not necessarily apply to products and services offered in each local market Technical specifications are subject to change without prior notice All other trademarks are the property of their respective owners 2009 10 us Printing for Professionals Professionals everywhere look to Oc for digital printing and document management In the office Oc systems keep the information of business and government flowing In manufacturing architecture engineering and construction Oc wide format printers set the standard while our display graphics systems help people produce banners billboards and other large colorful applications In corporate print facilities marketing service bureaus and the graphic arts industry Oc systems print transaction documents mailings newspapers manuals and books on demand and at the highest speeds And Oc Busine
14. ss Services manages the complete document workflows of customers around the world It all helps you go Beyond the Ordinary in printing and document management For more information visit us at www oce com
15. you move the machine Holidays Caution m Unplug the machine if you will be using it for a long period of time Chapter 1 Safety information 9 Instructions for safe use 10 Chapter 1 Safety information Chapter 2 Regulation notices Regulation notices country dependent Regulation notices country dependent Introduction This section describes the regulation notices Radio Interference Suppression all countries except USA Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate corrective measures FCC Approval USA Only This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide rea sonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense VCCI Japan Only This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology
Download Pdf Manuals
Related Search