LED Techno Strobe User Manual Rev. 4
Contents
1. 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector Then proceed to connect from the output as stated above to the input of the following fixture and so on ST 3000 LED User Manual 7 Rev 4 y Operating Instruction Ch fl VEL 4 Ing Instructions The ST 3000LED is a DMX 512 controllable flash LED panel made up of highly efficient and super bright white LEDs The ST 3000LED can operate in Stand Alone Master Slave and via DMX 512 control utilizing 3 channels A pe Standalone Mode Nae The ST 3000LED can be operated without a DMX controller in a standalone mode It can be operated as a single fixture or together with several other ST 3000LED fixtures in what is called a Master Slave configuration Single Fixture Mode The ST 3000 LED Techno Strobe can be set to operate independently of other fixtures or a DMX controller in either a sound active or automatic mode A serial data link is not necessary for this mode of operation and it is recommended that no connection to other fixtures be made at all 1 Simply choose from any one of 10 built in DIPswitch Options from the table below Master Slave Mode A master slave mode setup consists of more than one fixture connected in a serial data link without the use of a controller In a master slave operation the slave fixtures will s2. ll l le l lb ll le hh me le ls l le die le le la lea N O I A o Y O IN 0 IO 1O mr A oQ JH O O IN 0 HD IO Ir IN oQ Jr IO O IN D O IO IO IO O IO IO JO JIO O jrm je Jr jie je jie je je ANON N AN N N IN AN IN wee O 1 EER EE Ea a sO ce e ee ss E a 1 A R REE 10 eT ES NSO e A Oi GENEA NENS E a MTE e Ce Oe oe 1 coe e a Y O N O jm IN 0o Hr JO IN 0 JO IN Q Joa O N 0D IN V Y LO o CLO O O 1 o 0D IGO lO o O 1D D CV 0O Y O JO IR 0 O O r IN TO JH O O IN 0 HO JO Io IN jQ Y JO O IN JO IO JO r IN Q N 98 N 9 NN NN 90 JO Y Y Y Y Y Y Y Y Y NY JO FO FLO FO O O O O JO O O O DMX Address Rev 4 10 CHADVET OFF or ON X Binary Addressing Quick Reference Chart gic Fc cal AA AE E SO DIP switch Position ST 3000 LED User Manual CHAUIEL Appendix DMX Channel Values NOTE Please read all instructions carefully on fixture DMX control mode and addressing DMX channels 2 and 3 functions are determined by the current settings of channel 1 For example while Channel 1 is set between 000 and 029 the following conditions will apply Channel 2 will control Strobing from 0 to 100 Channel 3 will control Dimming Intensity from 100 to 0 Channel Value Function 030 059 060 089 1 210 gt 255 Sound Photometric 20 Beam Angle 163 1800 87 980 Ch2
3. Ch3 Strobe 0 255 Speed Intensity Slow Fast 100 lt gt 0 No Function 34 Foot Candles 383 LUX 0 304 ST 3000 LED User Manual 0 914 6 Distance feet 1 828 Distance meters 11 Rev 4 CHAUVET Appendix Technical Specifications WEIGHT amp DIMENSIONS Kus i a ee ae ec o ne ade cee A eos ee one ce ee eee eas 355 6 mm 14 0 in Mt 247 65 mm 9 75 in a A A a ey ea esse ee geese ee eee 165 1 mm 6 5 in WOON ite acre retornado toi teiisciias 2 22 Kgs 4 9 lbs Master PACK CAPO A po o e o A 4 pcs 12 84 Kgs 28 3 Ibs POWER ss 2 eee een Nee eee te et er Le eee a NCES Nee iran tc ene ee mee eee eee nee eee eee 90V 240V 50 60 Hz 0 A A IEC 60320 C14 EEE suertee aero erneieneal peak lt 12W 120V inrush lt 24W 120V FUSE I acento emcee sere 20mm Glass 2A Fast Blow LED A ee mR Oe ee eee ee ee ee ee 192 Total white lr go PP A PAP o deenecteagsecasenesesiacs 20 ITO Po ECO ote ae oer EEE 82 6fc or 888 8lux 1 meter CONTROL amp PROGRAMMING Data Plains roads locking 3 pin XLR male socket Ps e O A locking 3 pin XLR female socket Data O16 ON MOMMA A e ice pin 1 shield pin 2 pin 3 ns PP o E o O O ES PG E E An DMX 512 USITT DRD AIM rca 3 ORDERING INFORMATION Ar M er sn meee ree te reer etre cere eon eee er eee ee ST 3000LED Contact Us World Wide General Information Technical Support World
4. Wide Web ST 3000 LED User Manual CHAUVET Lighting 5200 NW 108th Avenue Sunrise FL 33351 voice 954 929 1115 fax 954 929 5560 toll free 800 762 1084 CHAUVET Lighting 5200 NW 108th Avenue Sunrise FL 33351 voice 954 929 1115 Press 4 fax 954 929 5560 Attention Service www chauvetlighting com SATELLITE READY Rev 4
5. lamp source e All Class fixtures must be connected to circuits with a suitable Earth Ground e To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure there are no flammable materials close to the unit while operating e Do not operate the fixture if covers are open or if any internal component is missing or damaged an unshielded discharge lamp emits dangerous UV radiation that can cause burns and eye damage e Make sure power cord is never crimped or damaged e Never disconnect power cord by pulling or tugging on the cord e This product is designed to be used with very specific lamp s Use of any other type of lamp not stated in this manual may create a fire hazard due to possible risk of lamp explosion Using the wrong type of lamp in this product VOIDS the warranty e Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked e Maintain a minimum distance of 1 meter 3 28 feet from combustible materials e Allow this product to cool for a minimum of 15 minutes before opening handling or removing the lamp in this product e Maximum ambient temperature is Ta 40 Do not operate fixture at temperatures higher than this Avoid dir
6. to remove dust collected on external vents and internal components Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint Do not to touch the lamp glass when cleaning fixture Oil and dirt can cause damage and premature aging of the lamp In the event that the lamp is touched or becomes dirty clean the lamps with an alcohol wipe The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days ST 3000 LED User Manual 9 Rev 4 Appendix DMX amp Binary Address Quick Reference Chart DIP switch Position 1 dd EUA ENANA A AE AEREAS ES 0 D gt JO I IN Q Jr IO JO Mm 0 O JO r IN O JH OO IN JO O O Jo IN lm JT WO O WR CO O CV IN N 0 JO NN SO JO 9 IO 0 0 Y Y Y Y Y Y Y Y TH Y FOO FO FO FOO FLO FLO FLO O O LO l le l
7. LED Techno Strobe ST 3000LED Fe SER MANUAL ve N L SATELLITE READY CHAUVET Voive anovation Performance CHAUVET 5200 NW 108th Avenue Sunrise FL 33351 U S A 800 762 1084 954 929 1115 FAX 954 929 5560 www chauvetlighting com Table of Contents 1 BEFORE YOU BEGIN o ccot canes ws tauce nnmnnn nnmnnn mnnn nnmnnn nnmnnn oa 3 O D TTT A A E 3 UNPACKING Aba 3 SAFE NOTES gee eo Po ee ee A iaie 3 Z INTRODUCTION Sotoca runa Aer a 4 Sani ES E A ho E it ite E tou a et coe ean enue dt de ar ease ener 4 DNS CHANNEL An II tanec 4 RITTER ele ie rs get NG Pe aoe A SOREN SENSE SE NOTE OLE Sr Sen NORA OT gon MOE Nate eT 5 a 6 ACPOWER nmu ea a a E add eo e aiOO 6 O ate A 6 FIXTURE LINKING tdi a cts sets a a a a AA ede 7 STANDALONE MASTER SLAVE FIXTURE LINKING sss sss sse sxs sse eee 7 4 OPERATING INSTRUCTIONS s sss lt s lt c c c scs eaea aaaeeeaa aaaeeeaa aaaeeeaa aeaaaee aaaeeeaa 8 SIAN BANKO N AY e EA A AA ALANES AEA AA EAEE EATE AAE A TE Wa LE IATE RE ERO TTT 8 GIS FOE nn o A test emenettte say tenia ticie nea tenineet at 8 Vase plave NOS 8 A e 8 pS OOE aaa n ves tccece caucststsuetcesestaaas uaceceestcecse snuet anes vetuans TTT 8 SAP PE ND o LE Leds 9 O A O O A A OO A A TTT 9 IE A 9 MANTENINCE aa Aaa ea cd ET 9 BINARY ADDRESSING QUICK REFERENCE CHART sss sss sse 10 DNIX CHANNEL O cet iene Se roe re te ewe oP nr ne RE he RA oe ESSA Oren eR AS SE TOR
8. S aT SOE Seg Tg SEAS OE ne aT ae eee NE eee oe 11 Sene h nS 11 TECNICAS ENS da 12 2 A a A 12 CHAUVET 2012 All Rights Reserved Information and specifications in this User Manual are subject to change without notice CHAUVET assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual ST 3000 LED User Manual 2 Rev 4 Before You Begin Ch fl l VEL L Before You Begin What ts Included e 1 x LED Techno Strobe ST 3000LED e Warranty Card e 1 x Power cable e Users Manual 2 x Flush Mount Brackets with screws Unpacking Immediately upon receiving a product carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned it is important that the fixture be returned in the original factory box and packing Safety Notes This product is designed for professional use It is not intended for use in a household environment Read this manual before installing or powering the fixture follow the safety precautions listed below and observe all warnings in this manual e Always disconnect from AC power source before servicing or replacing lamp or fuse and be sure to replace with same
9. ect eye exposure to lamp while it is on Do not operate the fixture if covers are open or if any internal component is missing or damaged Secure fixture to fastening device using a safety chain A hot lamp is an explosion hazard Do not open fixture for a minimum of 15 minutes after switching off Wear eye and hand protection when re lamping Fixture surface may reach temperatures of up to 160 C 320 F Handle fixture after it cools In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact CHAUVET ST 3000 LED User Manual 3 Rev 4 T CHAUVET 2 Introduction Features e 3 channel DMX 512 LED white strobe light e Blackout static dimmer strobe e Built in automatic programs e Adjustable flash rate dimmer and static via stand alone e Automatic built in programs with sound activation e Linkable with LED Techno Strobe amp LED Shadow M in stand alone e Low power consumption e Additional power output for daisy chaining units together DMX Channel Summary 1 2 3 DMX Channel Column
10. ircuit even if the rheostat or dimmer channel is used solely for a O to 100 switch Before applying power to a fixture check that the source voltage matches the fixture s requirement All fixtures must be connected to circuits with a suitable Earth Ground Power Cable Configuration CABLE Pin International Screw Color BROWN Live L Yellow or Brass BLUE Neutral N Silver YELLOW GREEN Earth EG Ground Green Mounting Orientation This fixture can be mounted on a truss using a clamp in any position or against a flat surface using the brackets provided Rigging The fixture includes a mounting yoke to which 1 rigging clamp can Hanging Clamp be bolted and 2 Flush Mount Brackets for flush mounting to flat surfaces You must supply your own clamp and make sure the clamp is capable of supporting the weight of this fixture You can order C clamps from any CHAUVET dealer or distributor 1 Block access below the work area and use suitable and stable platform when installing or servicing fixture Align the clamp screw with the center hole on the yoke and tighten Flush Mounting Bracket Verify the structure can hold 10 times the weight of all to be installed fixtures Adjust the angle on the yoke arm as necessary Always use a Safety cable or chain as a secondary source of attachment The safety cable must hold 10 times the weight of the fixture If safety cable attachment point is provided that i
11. s Dimmer 000 029 ZTE nz ee ld 030 209 N co es Sound Mode 225 255 No Function CONTROL MODES amp OPTIONS Rows For a detailed view of DMX values turn to the Appendix section in this manual Control mode parameters are set by DMX values in Channel 1 ST 3000 LED User Manual 4 Rev 4 Mf CHAUVET Introduction Product Overview Power Link Out f IEC Plug for AC Input amp Fuse Compartment Flush Mounting Bracket ST 3000 LED User Manual DI P switches DMX Addressing gt RUPPY LED Front Panel DMX OUTPUT Hanging Yoke de fee Audio Sensitivity Rotary knob DMX OUTPUT Red LED Power Indicator Blue LED Signal Indicator L 6 0 a wd l Ka 406 500 0 0 0 000 4640 0000000 606505200000000 AA A H H H 8 8 8 E A TH E E 5 i ee ee ee ee ee N i a NN i E E E E a DMX Input Rev 4 Setup 3 Setup AC Power Warning Verify that the power requirement label on your unit matches the line voltage applied All fixtures must be connected to circuits with a suitable Earth Ground To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture or refer to the fixture s specifications chart A fixture s listed current rating is its average current draw under normal conditions All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer c
12. s permanently affixed to the surface or body of the fixture use that instead of looping through a hanging yoke arm Flush Mounting 1 ST 3000 LED User Manual Draw a screw hole template on a large piece of vellum or transparent paper for best alignment Place paper against the mounting surface and drill holes or mark the surface for drilling Hang Panel 6 Rev 4 CHAUVET G Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX 512 controller or to run synchronized shows on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support The ST 3000LED Techno Strobe uses 3 channels of DMX control Important Fixtures on a serial data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 32 devices should be connected on one data link Connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal Maximum recommended serial data link distance 500 meters 1640 ft Maximum recommended number of fixtures on a serial data link 32 fixtures Standalone Master Slave Fixture Linking 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture
13. the model number serial number and a brief description of the cause for the return Once you have received the RMA number please include the following information on a piece of paper inside the box e Your name e Your address e Your phone number e The RMA number e A brief description of the problem Be sure to pack the fixture properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility FedEx packing or double boxing are recommended Claims Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customer s responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Any other claim for items such as missing component part damage not related to shipping and concealed damage must be made within 7 days of receiving merchandise Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or air compressor and a soft brush
14. ynchronize and will behave either identically or in a planned chase pattern to the master unit which must be the first in the serial daisy chain A Master Slave ST 3000LED system can consist of an unlimited range of fixtures or at least the number stated to conform to EIA 485 standards Setup 1 The ST 3000LED sets up automatically for Master Slave no DIP switch settings are required other than for selecting DIP switch Options 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connector to the DMX IN input connector of the Slave fixture consisting of a male 3 pin connector Continue the loop from DMX OUT to DMX IN DiPswitch Options Functions Dipswitches ON Notes amp Description Sound Active Music Sound Activated Rotary knob sets sound sensitivity Flash Speed 1 pC Flash Speed 2 p CC Flash Speed 3 pC Flash Speed 4 a slash Speed Flash Speed 6 Flash Speed 7 J CBC Flash Speed 8 Full On 9 JAlLEDsfullon Preset Program Preset Programs run in Automatic speed OJAN ST 3000 LED User Manual 8 Rev 4 y CHAUVET Del 5 Appendix Returns Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Return Merchandise Authorization Number RA Products returned without an RA will be refused Call CHAUVET and request an RA prior to shipping the fixture Be prepared to provide
Download Pdf Manuals
Related Search