Home

File

1. at 508 676 1000 or support aquabotix com Safety and Operational Warnings Assemble AquaLens in a safe dry place Do not assemble while submerged in water or allow AquaLens to get wet before it is fully assembled and enclosed in the watertight dome Do not assemble with wet hands AquaLens is powered by eight 8 AA Alkaline batteries Do not use any other type of battery or powering device for AquaLens Caution should be used when inserting or changing batteries Do not attempt to insert or change batteries into AquaLens while submerged in water Do not let the battery assembly area get wet Do not assemble with wet hands When using topside power to operate your AquaLens use caution to prevent shock or damage The AquaLens dome must be completely secured to keep it watertight Check the security of the dome before submersion To tighten line up the grooves and turn clockwise until it locks The topside box and LCD screen are not waterproof Do not submerge the topside box or LCD screen in water Do not let the topside box or LCD screen get wet AquaLens is meant for depths no greater than 50 feet from the water surface Do not go beyond this depth due to limitation as operational safety is not tested and rated for such depths Secure all cables on board to prevent tripping hazards Do not submerge cable connector plugs let them get wet or handle them with wet hands LEGAL DISCLAIMER Assure cable is properly secured to
2. AQUA MANUAL VERSION 4 Aquabotix Technology Corporation All rights reserved July 2015 Trademarks used in this guide Aquabotix and HydroView are trademarks of Aquabotix Technology Corporation Other names mentioned in this guide may be trademarks or registered trademarks of their respective owners TABLE OF CONTENTS LEGAL DISCLAIMER CHAPTER 1 SYSTEM Overview Specifications CHAPTER 2 ASSEMBLY Pole Attachment Topside Box Connection LCD Screen Wrist Mount Assembly LCD Screen Sticker Mount Assembly LCD Screen Screw Mount Assembly Batteries CHAPTER 3 MAINTENANCE CHAPTER 4 WARRANTY LEGAL DISCLAIMER Trademarks used in this guide Aquabotix and AquaLens are trademarks of Aquabotix Technology Corporation Other names mentioned in this guide may be trademarks or registered trademarks of their respective owners The purpose of this manual is to provide HydroView users with a clear understanding of operating procedures If further information is needed contact Aquabotix at Support aquabotix com or 508 676 1000 website www aquabotix com LEGAL DISCLAIMER Important Safety Instructions Assemble and use AquaLens only as instructed by this manual Read and follow these important safety instructions and the detailed assembly in this manual prior to using the AquaLens Follow all safety and operational warnings and heed all additional restrictions on use Refer all non routine service issues to Aquabotix
3. Velcro to the back of the LCD screen c This will then attach to a provided wrist band allowing you to wear the screen on your wrist 10 ASSEMBLY LCD Screen Sticker Mount Assembly a Attach the swivel mount to the provided pre cut sticker and mount directly to your desired location b Move the screen up and down for convenient viewing 11 ASSEMBLY LCD Screen Screw Mount Assembly a Attach the swivel mount directly to your desired location using 4 screws not provided b Move the screen up and down for convenient viewing 12 ASSEMBLY Batteries a Remove dome turning counterclockwise Use caution when handling your dome to prevent scratches and to protect clarity Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal b With viewing sphere facing you loosen not remove both screws with your fingers c Swivel battery access plate to get to battery pack d Disconnect the battery pack using the battery electrical snap e Insert eight 8 AA batteries not supplied Reconnect the battery pack using the battery electrical snap Swivel battery access plate to cover battery pack Tighten both screws on the access plate with your fingers Re attach dome by lining up the grooves and turning clockwise until it locks Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal 13 MAINTENANCE Removing Dom
4. all important safety instructions CHAPTER 1 SYSTEM tattecth to loreari 3 5 LCD screen Arm band Swivel mount Built in connection Video out composte 12 VDC connector Standard 15 ft Cable optional lengths 25 and 507 Universal fit to any pole Standard attacher Viewing sphere Video camera 640 X 4680p LED ignting Anti fogaing technology Battery compartment Btw coter tte O te wr LED s SYSTEM Specifications Diameter Weight Depth Operating Voltage Battery Run Time Monitor Camera Color 5 inches 10 pounds 50 feet cable dependent 10 VDC 10 hours 8 AA batteries required 3 5 inch LCD screen Total resolution 640 x 480 Yellow CHAPTER 2 ASSEMBLY Pole Attachment preferred method If using a pole with threaded end a Thread the angular adapter into the hole on the back of the viewing sphere Be sure to align the angular adapter vertically with the camera b Thread your pole into the angular adapter ASSEMBLY Topside Box Connections a Attach the camera connecter cable to the topside box b Attach the AC power adaptor for continuous use optional c Turn the power switch on d Toggle the lights on off Please note The lights will not turn on unless the power switch is turned on ASSEMBLY LCD Screen Wrist Mount Assembly a Unscrew the swivel mount from the LCD screen b Attach the provided pre cut piece of
5. e To remove dome turn counter clockwise and remove Use caution when handling your dome to prevent scratches and to protect clarity Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal Cleaning Dome Using an acrylic glass cleaner spray onto surface of dome and rub in witha microfiber cloth Preventing Fogging On Dome 1 Remove dome turning counter clockwise Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal 2 Spray a small amount of anti fogging spray on the inside surface of dome 3 Wipe area with a small cloth until surface is clear 4 Re apply as required After Water Care 1 Rinse AquaLens with fresh water 2 Wipe down using a microfiber lens cleaning cloth 3 Safely store AquaLens cover dome to protect from scratches 14 MAINTENANCE Recommended Replacement Periods O ring Every 6 months Moisture absorbing pack Every 6 months To purchase these from Aquabotix visit our online store accessed through our website at www aquabotix com Replacing O ring 1 Remove dome turning counter clockwise 2 To remove O ring use an O ring removal tool or something flat that can remove it such as a flat head screwdriver or tweezers 3 Remove replacement O ring from package Inspect for cracks and tears 4 Lubricate O ring with an O ring lubricant found at most hardware stores 5 Insert O ring Use cautio
6. e a defective product which is covered by Aquabotix s warranty Aquabotix shall within a reasonable time after being notified about the defect refund the full purchase price of the product Aquabotix shall have no obligation to repair replace or refund the purchase or product until the customer submits an RMA form and returns the defective product to Aquabotix Warranty does not cover the following damage caused by abuse or misuse improper maintenance incorrect assembly accidental damage or damage due to incorrect power connection as described in the user manual Consumable items including o rings moisture absorbing packs LED lights and batteries are specifically excluded from the warranty Items subject to normal wear and tear include but are not limited to the lens and the outer shell which are only covered for defects in workmanship or materials In no event will Aquabotix be liable for any incidental or consequential damages Claims for damage shortage or errors in shipping must be reported within three 3 days following delivery to the customer Aquabotix is not responsible for returned items lost or damaged during shipping A copy of the dated receipt or bill of sale from the original end user purchase is required to determine coverage This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state This model of the AquaLens is intended for personal and recreational
7. n when handling O ring to be sure the area remains clean to ensure a water tight seal 6 Re attach dome by lining up the grooves and turning clockwise until it locks 15 MAINTENANCE Replacing Moisture Absorbing Pack 1 Remove dome turning counter clockwise Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal 2 Pull off black cap 3 Moisture absorbing pack will be exposed 4 Take out moisture absorbing pack and replace 5 Re attach black cap 6 Re attach dome by lining up the grooves and turning clockwise until it locks Use caution when handling O ring to be sure the area remains clean to ensure a water tight seal 16 WARRANTY AquaLens One Year Limited Warranty Certificate Aquabotix warrants that under normal use and service the AquaLens will be free from defects in material and workmanship for one year from the date of purchase applies only to the original purchaser and may not be transferred Unless authorized by Aquabotix any modification customization repair disassembly of the product abuse exposure to contamination excessive electric or magnetic force will void this warranty If Aquabotix receives during the applicable warranty period notice of defect in any product which is covered by Aquabotix s warranty Aquabotix shall either replace or repair the product at Aquabotix s discretion If Aquabotix is unable to repair or replace as applicabl
8. pole with adapter or straps before use AquaLens will sink if not properly secured Inspect AquaLens prior to use If there is any sign of water inside the camera or housing unit or other damage do not use Send AquaLens to Aquabotix for service Do not attempt to dislodge or pry foreign objects from AquaLens Send AquaLens to Aquabotix for service Additional Restrictions On Use AquaLens is meant for operation by adults over 18 years of age only Keep AquaLens out of the reach of children and supervise children and pets when AquaLens is in operation Do not use AquaLens in rain rough sea conditions and or storms Do not use AquaLens while underwater machinery is in operation Do not touch AquaLens to underwater marine growth Keep AquaLens clear of all underwater objects Do not expose AquaLens to high temperatures above 40 C 104 F avoid direct sunlight Use AquaLens in the recommended operating water temperature range of 2 C 35 F to 32 C 89 F Dropping AquaLens or subjecting it to strong force may damage the device and its watertight dome Handle with care A Failure to follow these important safety instructions and the detailed assembly and use instructions of this manual will void your limited warranty from Aquabotix and may result in serious injury or death Aquabotix disclaims all liability arising from or caused by the failure to assemble and use HydroView in accordance with this manual including
9. use only Aquabotix offers a separate commercial grade PRO model of the AquaLens for use in commercial applications The use of this model for commercial applications will void this limited warranty For further information contact Aquabotix at returns aquabotix com or 508 676 1000 17

File

Contents

Download Pdf Manuals

Related Search

Related Contents