Home

ADPRO Presidium by Xtralis Installation and User Manual

1. Doc 12384_05 99 Installation and User Manual ADPRO Presidium by Xtralis Table 10 Horizontal FOV 30 Metres 98 Feet 1 4 camera format 1 3 camera format 1 2 camera format Max Distance Dead zone Max distance Dead zone Max distance Dead zone metres feet metres feet metres feet metres feet metres feet metres feet 4 8 45 148 6 21 30 98 4 12 22 73 2 7 6 0 56 185 8 27 37 123 5 17 28 92 3 11 8 0 75 247 11 38 50 164 7 24 37 123 5 17 12 0 112 371 17 57 75 247 11 38 56 185 8 27 16 0 150 495 23 77 100 330 15 51 75 247 11 38 25 0 234 773 37 121 156 515 24 80 117 386 18 60 Note Caution should be used with the detection ranges shaded grey At these ranges camera visibility and system performance could be adversely affected by rain mist dust storms snow or aggravated camera vibration Camera mounting height 4 2 metres 14 feet 100 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Appendix F Commissioning Checklist Company Date Location Commissioned by 3 Detection Test Parameters Channel No Detection Test Documented Soak Test Recorded 10 11 12 13 14 15 16 17 18 19 20 Doc 12384 05 101 Installation and User Manual ADPRO Presidium by Xtralis 102 Doc 12384_05 ADPRO Pr
2. Normally Closed DEOL Short Circuit Tamper Low Impedance Sealed Hi Impedance Alarm Open Circuit Tamper Figure 30 Access Secure Input Configuration 3 9 2 Fault Relay Presidium has a fault relay which is a Form C single pole changeover contact available on pins 3 4 and 5 of the General Inputs Outputs connector The relay has the following behaviour Table 3 Fault Relay Normally Closed FLT NC Normally Open FLT NO Unit State Pole Pole Power Off Status LED is off Open Closed Unit powered on and is booting i e the Status Open Closed LED is on Operating Normally Status LED is off Closed Open Any system fault is detected Status LED is Open Closed on In the case of an over temperature situation standard Presidium only the fault relay will indicate a fault condition and the unit will turn off but no front panel LEDs will be illuminated A hard power cycle must be performed to restart the unit Refer to Specifications on page 89 for the relay specifications Doc 12384 05 39 M NI Installation and User Manual ADPRO Presidium by Xtralis 3 9 3 General Alarm Relay Output Pins 6 7 and 8 contain a Form C single pole changeover contact set The general alarm relay GAR will activate i e the normally open pole will close if any of the following valid alarms are triggered on any channel of the Presidium video motion detection e contrast
3. System Installers Facilities Building Site Managers 2 1 4 Other Resources A number of other resources should also be used in conjunction with this Design Guide Presidium Design Forms refer to System Design and Equipment Checklist on page 97 Presidium Commissioning Forms refer to Commissioning Checklist on page 101 Presidium Maintenance Forms refer to Site Maintenance Tables on page 105 Where Remote Monitoring is a requirement the Central Monitoring Station Design Guide should be used in conjunction with this Design Guide 2 2 Quick Guide This guide divides the implementation of an Presidium system into four main areas System Design System Installation Site Commissioning Site Maintenance The Quick Guide shown in Table 1 provides an overview of key design considerations allocated in each step and may be used as a quick reference It should be used in conjunction with the entire Presidium Manual to produce a robust system design Table 1 Quick Guide Reference Site Survey amp Checklist Key Design Considerations Conducting a site survey and what information should be gathered Site Survey on page 7 and Site Survey Checklist on page 93 Illumination Illumination selection and location for llumination Requirements on page 19 use with Presidium Cameras Camera selection and location for Camera Selection and Location on page 11 use with Presidium Camera PIR Alignment on pa
4. Doc 12384 05 63 Installation and User Manual ADPRO Presidium by Xtralis VMD Video Motion Detection 1 Select the required Hold Time for the VMD See the explanation of Hold Time above Alarm Generation An alarm may be generated when an alarm input OR VMD is triggered or alternatively when an alarm input AND VMD is triggered The AND function should be used if the background of the detection area has high environmental activity Channel Isolation Isolating a channel prevents that channel from generating alarms This feature is useful in a number of scenarios Commissioning a Presidium Fault finding an installation Configuring detectors Disabling faulty detectors 1 Select the type of the Isolation Input Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resistor Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL Note Any tamper on the isolation input will generate an alarm and activate the general alarm relay Alarm Output Behaviour The way that the alarm output behaves can be set 1 Select the behaviour options required When Alarm active the output is active while the alarm condition is present Pulse on Alarm a specific time duration may be defined by Pulse Length Pulse Length seconds is only available for the Pulse on Alarm behaviour option It can be Set between 1 and
5. FastTrace User Settings Category Site Details Date Time Settings Licensing ons Connected Equipment Cameras Monitor Transaction Devices Transparent Data Port Alarm Inputs Presidium Inputs Control Outputs Audio Arming Disarming fineralional Rehavinur v 2 Information and Help accessing the FastTrace unit Save to FastTrace Configure the communication ports for Ethemet Properties Ethemet Settings Serial Communication Properties Serial Communication Port 1 Settings Serial Communication Port 2 Settings Advanced Communication Properties Advanced Communication Settings Configure Configure Configure Save to File Load from File Discard all changes Figure 76 FastTrace FastTx FastTrace R Communications 2 Select the Configure button in the Advanced Communication Properties section 82 Doc 12384_05 MINI MINI ADPRO Presidium by Xtralis Installation and User Manual Adyanced Communication Properties x Base Port Number 15000 Connection Timeout 1 300 seconds 5 Enable WAN optimisation PPP Settings PPP Request Timeout 1 10 seconds iD PPP Maximum Retries 5 50 10 Presidium High Level Interface Properties 15020 v Listener Port Number Figure 77 Advanced Communication Properties 5 3 1 Presidium High Level Interface Properties When a Presidium is connected to the FastTrace FastTx FastTrace R th
6. Q2 Concrete Figure 6 Recommended Presidium Pole Installation The position of the cameras relative to lighting is extremely important Do not install cameras Close to lights particularly infrared illuminators which could attract insects or face cameras into lights windows the sun or in areas which have a large number of reflections or shadows When the lighting is below or to the side of the camera the recommended safe distance is 2 metres 6 feet If the lighting is directly above the camera then insects flying up towards the light in front of the camera may cause nuisance alarms or obscure the view If this is the case ensure that the lighting is well above the camera in excess of 4m The previous image of the pole shows the location of an IR illuminator The figure below shows this in greater detail Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual ADPRO PRO Detector 1 8m 6 Q IR Illuminator optional Figure 7 Presidium Pole Front View Do not install cameras facing at trees or plants which may move in the wind or drop leaves tree shadows may also move in the wind In many circumstances this is unavoidable but should be limited as far as possible Use the Presidium detection area selection functionality to mask out areas with foliage Do not install cameras facing into areas where there is likelihood of vehicle headlights at night The presence of roads near sites is una
7. This enables the complete configuration to be saved This may then be reloaded in the case of a system malfunction or used to configure another system The configuration is saved as a settings file in a user defined location on the PC 70 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 4 5 2 Loading a Configuration from File Selecting the Load from File button displays the Load Settings from File window Load Settings from File Look in e Setup Utility 1 0 Qimageformats J plugins MyRecent jtranslations Documents E defaults settings 3 My Network File name Places Files of type Presidium Settings Files settinas Figure 63 Load Settings from File 1 Navigate to the required settings file and select Open 2 Select the Save to Presidium button The saved configuration is uploaded to the connected Presidium Note It is not possible to load settings from a Setting File created by an older version of the Presidium firmware If Presidium is upgraded then a new settings file should be saved after the upgrade is completed 4 5 3 Printing the Site Configuration Selecting the Print Settings button displays the following screen General Select Printer L5 Add Printer Em 1 Step RoboPDF Eg HPB150DN Sy Adobe PDF Eg HPB550N Status Ready Print to file Preferences Location Comment Find Printer Page Range e All Numb
8. ADPRO Presidium by Xtralis includes Presidium Mini Installation and User Manual March 11 2010 Part 201975 05 ADPRO by xtralis ADPRO Presidium by Xtralis Installation and User Manual Disclaimer The contents of this document are provided on an as is basis No representation or warranty either express or implied is made as to the completeness accuracy or reliability of the contents of this document The manufacturer reserves the right to change designs or specifications without obligation and without further notice Except as otherwise provided all warranties express or implied including without limitation any implied warranties of merchantability and fitness for a particular purpose are expressly excluded Intellectual Property and Copyright This document includes registered and unregistered trademarks All trademarks displayed are the trademarks of their respective owners Your use of this document does not constitute or create a licence or any other right to use the name and or trademark and or label This document is subject to copyright owned by Xtralis AG Xtralis You agree not to copy communicate to the public adapt distribute transfer sell modify or publish any contents of this document without the express prior written consent of Xtralis General Warning This product must only be installed configured and used strictly in accordance with the General Terms and Conditions User Manual and pro
9. Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Suitable Unsuitable Perimeter Conditions sess eese entes Suitable Unsuitable Area Detection Scenes sss Required Video Signal sse Camera Dead Zone ssss sss enne nens Camera Dead Zone Coverage sss Recommended Presidium Pole Installation sseeee Presidium Pole Front View FOV of Curtain PIR with Camera FOV of Wide angle PIR with Camera Camera PIR Mounting Details sse Camera PIR Dead Zone Comparison sess ene enne enne nenne Optimal PIRANG UE PIR Alignment on Fenceline sene Example PIR Baier Camera PIR Algnment sss enne Correctly Illuminated Scenes s sss Typical Connections to a standard Presdum test iettt nesr nesrrnssrnssr ressens PIR Alignment on Fenceline seen Rear View of the Presidium sse Cable Entry Requirements esses Rear View of the Presidium Mini enclosure seen Typical Conn
10. 1 Highlight the custom level to be modified 2 Modify the Video Motion Thresholds on the right side of the window as required values outside of the valid ranges will not be able to be entered 3 Select OK The window closes and the modified level is selected for this channel Table 5 Video Motion Thresholds Explanation Threshold Explanation Minimum Area sq m The minimum area in square metres an object must be to generate an alarm Maximum Area sq m The maximum area in square metres an object must be to generate an alarm Minimum Width m The minimum width in metres an object must be to generate an alarm Maximum Width m If an object is wider than this measurement it is deemed too large to generate an alarm Minimum Height m The minimum height in metres an object must be to generate an alarm Maximum Height m If an object is higher than this measurement it is deemed too large to generate an alarm Minimum Speed m s The minimum velocity in metres per second that an object may be to generate an alarm Maximum Speed m s The maximum velocity in metres per second that an object may be to generate an alarm Minimum Distance m The minimum distance in metres that a motion detection track must be to cause an alarm Note If the intruder has taken a meandering path the track length is measured as the crow flies and not along their entire distance of travel
11. Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL Note If the Presidium is to be connected to a FastTrace FastTx FastTrace R ensure the Access Secure input is set in the default state of Normally Open and that nothing is connected to this input This ensures the Presidium is in the Secure state at all times and access is controlled at the FastTrace FastTx FastTrace R Authentication A Password is required to access Presidium setup or software upgrade Presidium Mini requires a Username and Password for setup or software upgrade The default password and username is admin this should be changed to a user defined password The new password takes effect once the Save to Presidium button is pressed Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Default Settings The Default All Settings button resets the channel password and network settings It also disconnects the Presidium Note To reconnect to the Presidium it may be necessary to change the PC network settings if the Presidium network settings have been previously modified 4 4 9 Status Tab The Status screen displays the value of all settings that have been entered for each channel ADPRO Presidium Device Status Dres Disconnect ADPRO Presidium Figure 60 Status Tab 4 5 Saving the Site Records 4 5 1 Saving a Configuration to File Selecting the Save to File but
12. Typical Video Transmitter User Settings Doc 12384 05 79 MINI Installation and User Manual ADPRO Presidium by Xtralis 5 2 Note Presidium Inputs At least one Presidium Input must be configured If there are no inputs configured the following Presidium system alarms will not work at the FastTrace FastTx FastTrace R Presidium Operational Tamper alert Over Temperature Communication to Presidium Lost Communication to Presidium Resumed Presidium Fault The Presidium Inputs option under the Connected Equipment menu enables the configuration of video motion detection alarm output from a Presidium to enable alarms on the FastTrace FastTx FastTrace R unit 1 Select the Presidium Input number from the displayed list FastTrace User Settings Category S Site Details Presidium Inputs Date Time Settings Channel Name Configure Communications KR Presidium 2 Coll List Presidium 3 Connected Equipment Cameras Monitor Transaction Devices Transparent Data Port Alarm Inputs Presidium Inputs Disconnect Presidium 4 Presidium 5 Control Outputs Audio Arming Disarming fIneratienal Rehaviei ir Information and Help Define the configuration of the Presidium inputs linked to the unit Save to FastTrace Save to File Load from File Discard all changes Figure 72 Presidium Inputs List The status of an Presidium Input is shown by a small icon to
13. Change Video Standard This screen enables PAL or NTSC to be selected as the video standard 3 Select the video standard of the cameras connected to the Presidium and select OK The following screen is displayed Doc 12384 05 51 Installation and User Manual V Presidium Setup Utility ADPRO Presidium Setup Channels Network High Level Interface Channel List Channel Name Paddock Carpark Gate Front OF Building End OF Building Main Foyer Staff Entrance CS M amp S S leeooxoneome Channel Status Channel Name Paddock Camera State Connected VMD Rule OR EE an Unit of Measure Select the unit of measure Metres Feet to be used for displaying and storing the settings Current Unit of Measure Metres Video Standard The Video Standard PAL NTSC should be set to match the cameras connected to the Presidium Current Video Standard PAL Load Save ALL Settings Full Carpark View From Front Foyer Entrace TestLab Entrance Canteen Hallway Load from File Save to File Disconnect ADPRO Presidium Figure 44 Presidium Setup ADPRO Presidium by Xtralis Save to Presidium The Connect button is used to enable a channel to detect alarm conditions To temporarily disable the use of a camera and any alarms that may be generated by it the Disconnect button is used For example Disconnect can be set if maintenance is being performed on that camera or if no camera i
14. Detection Tests iere reti pa resa deae mentee AS 2 8 5 Maintenance to Regulatory Requirements S 3 Presidium GConnectors 2 eru ds Sates dures maces quen NEEN dun gu M ann aud Nardo nr Deum e de ELO P 3 2 Presidium Mini cet 5 iieri auci race SEENEN ceeds NEEN eege Eed eran Dr aedi a na OO 3 3 Power Connection otra cerne tege ere ESA Geer 9 9 T le Un EE Bis 2 PresidiumMIFl tee e EE ee Ee 32 SEENEN e 3 5 Video Connections ai icio rui drin in ni ENNEN KENE ENNER an ma CR ara dn dt da c RC coaud varedveddeacecdsvecceadsectuaa G2 3 6 Alarm Inp tls ca ca cease Sec ee rere ceret terna EEEE EE te aur exe NEEN ip quon Eege KWAlEnIEu pl emt c EE 3 8 Alarm e CES OF 3 9 General UO Connector eeeeeeeiseeeeeieneees eene nennen nn snnt nnnn nene nnne nnn nennen OL 3 9 1 Access Secure InpUt 2 o inet te ete e DIESE 3 9 2 Fault Relay DEC 3 9 3 General Alarm Relay Output T L 3 10 Network Communications eeeseeeeeeee eese enne rennen ne ne EE nenen nnmnnn ener 4Q 3 101 PFeSIGIUITES R A E ehe heo e Ee e Ee ENT 3 10 2 Presidium Mini EEEE E EE E E E E 40 3 10 3 Network Connector LEDS d Tt Status LEDS mics cobs occ a r SEENEN ch EE o A aaia aaa aa Ad 4 Installation Configuration sisitan NEEN aneia si eunana bude adain ain ao nenne aeaii nns nnne
15. Extra Low Voltage SELV rated Failure to do so will invalidate the electrical safety approval and may cause injury or loss of life Contact Us The Americas 1 781 7402223 Asia 852 2916 8894 Australia and New Zealand 61 3 9936 7000 Continental Europe 32 56 24 19 51 UK and the Middle East 44 1442 242 330 www xtralis com Doc 12384_05 iii Installation and User Manual Declaration of Conformity Manufacturer s Name Manufacturer s Address ADPRO Presidium by Xtralis Xtralis AG Pty Ltd 4 North Drive Authorised EU Representative Virginia Park 236 262 East Boundary Road Bentleigh East VIC 3165 Australia Xtralis UK Ltd Vision House Focus 31 Mark Road Hemel Hempstead Hertfordshire HP2 7BW UK declares that the product s Product Name ADPRO Presidium by Xtralis Intelligent Video System Model Number PDM xx VM 15 Product Options All Product Name ADPRO Presidium Mini Intelligent Video System Model Number PDM Mini meet the Standards detailed below EMC Emissions EMC Immunity Safety EN55022 1998 CISPR 22 1997 A1 A2 AS NZS CISPR 22 2006 Class A Conducted and radiated emissions FCC Part 15 Class A Conducted and radiated emissions EN 61000 3 2 2000 A1 A2 Current harmonic emissions EN 61000 3 3 1995 A1 Voltage fluctuations and flicker EN 50130 4 1995 A1 A2 Alarm systems immunity EN 60950 1 2001 Safety of Information Technology Equipment IEC 60950 1 2001 1991 Saf
16. Minimum Density 96 The minimum allowed ratio of motion detection pixels to bounding box area for each tracked object For example the bounding box area for a tree may be very large if there is movement at the extremity of the branches but the number of motion detection pixels through the rest of the box may be small whereas a moving human will generate a large number of detection pixels for a relatively small bounding box Scene Change Threshold Kal If the scene changes by the percentage specified the scene learning mechanism is retriggered This may prevent nuisance alarms caused by sudden changes in lighting levels eg when lights are turned on at night Note It should not be necessary to change this value with normal use Scene Change Holdoff s The scene change percentage specified above must exist for this length of time before the scene is relearnt Note It should not be necessary to change this value with normal use Detect Delay seconds A track needs to continue to meet the size area velocity and density criteria for this duration before an alarm will be generated The remaining criteria must also be met before an alarm can be generated Subject to the figure entered in the Detect Delay parameter Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Note The above thresholds may also be displayed in feet depending on the selection made in Camera Calibration Disp
17. Soak test the system refer to Soak Tests on page 26 Perform system tests refer to System Tests on page 26 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 Doc 12384_05 Design Guide 2 1 Introduction The Presidium Intelligent Video System is designed to provide reliable and predictable detection of intrusion into secure areas The system analyses images from strategically placed CCTV cameras to detect human like movement and if the movement fulfils a number of criteria alarms are generated These alarms can be handled locally or coupled with ADPRO FastTrace ADPRO FastTx and ADPRO FastTrace R and Monitoring Software can be transmitted to a remote central monitoring station assessed and managed by experienced security personnel A well designed installed and maintained Presidium system can remove the need for onsite guards or patrols or provide an adjunct to local monitoring improving the effectiveness of the overall site security 2 1 1 Purpose The purpose of this Design Guide is to describe the specification design installation commissioning and maintenance of Xtralis s ADPRO Presidium Intelligent Video System The recommendations presented are designed to achieve optimal system performance and high reliability Although there are many variations to the recommended scenarios any departure from these recommendations may result in less than ideal system performance This document des
18. and reliability in the outdoor environment Presidium Mini is a high performance DC powered 2 channel video movement detection system in a desktop wallmount enclosure for the protection of smaller properties Note For consistency in this manual the generic term Presidium is used to refer to both standard Presidium and Presidium Mini Important This symbol is shown next to the section where a feature or procedure is not applicable to the Presidium Mini Presidium employs state of the art digital signal processing hardware and software to provide a high level of performance by reducing unwanted alarms without compromising detection The Presidium has been designed to be fully compatible with all CCIR PAL and RS170 NTSC CCTV systems monochrome and colour It is simple to include in new designs or to retrofit to existing CCTV systems to improve security 1 1 Features of the Presidium Modular expansion from 2 to 20 channels per Presidium chassis Advanced algorithms to maximise target acquisition and tracking under a wide range of environmental conditions Low probability of false alarms from small animals clouds wind and rain Multiple free form detection zones Additional functionality to enhance the Presidium detection capability and reduce unwanted alarms to near zero such as directional object detection dual edge trigger areas used to qualify alarms single edge target detection and timer enabled detection for sterile
19. avalabin the ADORO Presidium rd automatically assign an IP address starting with 169 254 This enables youto The ADPRO Presidium has three external Communicate with the device in the absence of a DHCP server since Windows automaticaly assigns network ports providing convenient ae IP in this range f no DHCP server is present access for IMPORTANT If you change the ADPRO Predam network settings alter you save the changes to the device you may need to change your PC network settings to be compatible with the new e Installation redes Connecting a second device such as an ADPRO FastTrace Load Save ALL Settings Load from Fle besen e stirs areto resis ove Disconnect ADPRO Presidium Figure 55 Network Tab Device Name The Device Name will be displayed in the list of local units when connecting to a Presidium refer to Figure 37 IP Address Configuration Note If the Presidium is to be connected to a FastTrace FastTx FastTrace R a static address in the same range with the same subnet mask as the FastTrace FastTx FastTrace R must be entered refer to Connection to ADPRO FastTrace FastTx FastTrace R by Xtralis on page 77 for more details 1 Selectthe Configure button to display the IP Address Configuration screen IP Address Configuration Obtain an IP address automatically DHCP Client Use the following IP address Static IP address 192 168 p v4 Automatically As
20. cable connect your PC to fe Setup Port of the Presidum 3 Wait up to 60 seconds for a devine to appear in the list below 4 Solt device from the list and prove Connect Select from List of Local Units Auto Detected a To connect to a device on a remote network enter the network address and port ol the remote device below E Enter Network Address IP Address or Host Name IP Address e 290 9 en Poet Sytem bie Connect ADPRO Presidium Comet Treiben Seay Ud Verven 02 16 32 babl 0004 Figure 39 Entering IP Address and Port Number 48 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 Once the connection to the Presidium is established the Password screen is displayed refer to Section 4 4 3 Presidium Mini 1 The Presidium Mini requires connection to two consecutive IP Address on Port Number 80 The default addresses are 192 168 1 3 and 192 168 1 4 on Port 80 2 While some network configurations may allow the use of two IP Addresses other simple network configurations such as xDSL may not To allow connection via simple xDSL services for example the Port Redirection feature of the xDSL Router connected to the Presidium Mini can be used This will cause two public ports to be redirected to the private Port 80 utilised for both addresses Refer to Figure 40 for an example using a DrayTek xDSL Router of redirecting two public ports in this example Port 81 and Port 82 to Po
21. failure a backup supply would also need to provide power for all the cameras and other detectors as well as any communications equipment Refer to Power Connection on page 32 for details on power consumption and the manuals for respective equipment for their power consumption details Access Requirements Access to Presidium equipment should be limited to authorised personnel An access control system may be used to limit access Equipment Mounting Presidium is compatible with 19 racking systems To ensure proper cooling ideally allow spacing equivalent to 1U between different equipment in the racking Consider providing cooling within the rack if the rack has a significant amount of equipment Presidium Mini is housed in a desktop wall mount enclosure To ensure proper cooling the enclosure must be location where it is clear of other heat generating equipment for example computers printers photocopiers generators etc Do not place the enclosure in a position where it will be subject to strong or continuous sunlight Monitoring Equipment A standard Presidium system may be remotely monitored through a FastTrace FastTx FastTrace R and VideoCentral Refer to the Central Monitoring Station Design Guide for details of selection configuration operation and maintenance of the remote monitoring station equipment Communications Infrastructure For remote monitoring to be used with ADPRO products suitable communications infrast
22. national electricity code USA use a UL listed type SVT or SJT detachable power cord Canada use a CSA certified detachable power cord Radio Interference The Presidium complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The Presidium complies with the electromagnetic emission limit requirements of AS NZS CISPR22 and EN55022 Class A In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Internal Lithium Battery Caution The Presidium contains an internal lithium battery There is danger of explosion if the battery is incorrectly replaced The battery is not user replaceable and can only be replaced by Xtralis or their Authorised Service Representative Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Compliance of Power Cord Caution If the power cord supplied with the Presidium or the Presidium Mini plug pack is not suitable for your local power connection do not modify the cord or plug pack Please purchase a power cord that has the safety approvals appropriate for your country Connection to Other Equipment Caution All interface ports on the Presidium must be only connected to other equipment or systems that are Safety
23. nn nre nennen AO 4 1 Unpacking E E 4 2 Install FA Utility ee EE 4 3 Configure the PC Network Connections nesciens 4D 4 4 Configure Presidium ET vg 4 4 1 Connect to an Presidium ERE Ti Presidium standard ege Nd etes dre be cose one Pk re Lp n i dd 48 Presidium MIDI arre entered ah eit ee ceed 49 4 4 2 Setup Utility No Activity Timer e DO 4 4 3 Using the Setup Utility 50 4 4 4 System Stalus ec bee UL aia daa dee eae 53 4 4 5 Configure Channels cccceccececceeceeee cece eeecaeeeeeeeeceaeeaeeneeeeeeeaeseeaeesseeeaeenaeeneneaees 54 General Setup EE 54 Camera Calibrations eens ierit taper e rri e e DD it epe AEN 56 Areas Ugh eR GA d rege pueda bee de cai uen du sd t e Trigger Area Properties dE E ETE PE 58 Detection Parameters 20 2 2 cece a iae e RENE ee EE EEN EAE 60 Alarm Behaviour esses eese ener nennen nennen enne nennen eee OG Video Monitoring WEE 65 4 4 6 Network Tabs ete eet wei puo etoce ct pe cp ate teo fbrte DO Device Name aine ccr deu beca a enu ds yea Ai P rege d dnd di 66 IP Address Configuration e D I 4 4 7 High Level Interface Tab ccc cece cece ce REENEN KEREN ENEE cane entente nnns 67 Doc 12384_05 ADPRO Presidium by Xtralis 4 4 8 Security Tab Access Secure Input Type uM AX ACD E EE EE A Mx e UEM CM E AUtN NtiCatlon eL Default Ge 4 4 9 Status Tab 4 5 Sa
24. of small targets The tables in Appendix E show the approximate maximum distance between the camera and the target for reliable detection at a maximum horizontal field of view of 20m 66ft 22m 75ft and 25m 82ft respectively The approximate dead zone beneath the camera is also shown for a camera mounted at 4 2m 14ft although this will vary depending upon the final angle at which the camera is set These figures should be used for guidance only Other considerations such as lighting and external environmental aspects may dictate the use of different camera lens combinations The formula for determining the distance from camera to target based upon the maximum horizontal FOV is as follows Lens focal length x Maximum horizontal field of view Distance between camera and target Camera format width Where Distance between the camera and target is in metres Maximum horizontal field of view is in metres Lens focal length is in millimetres Camera format in millimetres 8 8 mm for a 2 3 camera 6 4 mm for a 1 2 camera 4 4 mm for a 1 3 camera 3 2 mm for a 1 4 camera Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual 4 Dead Zones The dead zone is the area under the camera that the camera cannot view and should be considered during system design The following figure shows the dead zone area Camera Camera Dead Zones Figure 4 Camera Dead Zone Camera positioning should be such t
25. of the PIR using another person as an IR target when required Determine the level of intrusion to be detected such as a casual opportunistic intruder or a well planned and executed covert intrusion Design and document tests based around the security level and scene content Factors that may vary include the speed of target the size of the target and the location in the scene The following describes how to perform the tests and is suitable for both the PIR and Presidium detection testing Tests should be performed at three separate locations the foreground FOV in the middle of the scene and at the maximum FOV The target should move to the point where intrusion would expect to start If this is within the detection area then once the target has moved to the start point the target should stay motionless for one minute to allow Presidium to settle The target should then perform the detection test As a minimum a walk test and a run test should be performed at each distance More tests can be performed as required in each individual scene but most importantly all possible intrusion points must be tested For size discrimination testing a small target such as a basketball rolled across the scene could be used to check that small targets are or are not being detected by Presidium as required Doc 12384 05 25 Installation and User Manual ADPRO Presidium by Xtralis 26 Execute tests in each detection area based on the ty
26. on which the Presidium High Level Interface communicates with the FastTrace FastTx FastTrace R Do not change this setting unless instructed by Xtralis technical support LN Presidium Setup Utility at the IP address specfied below You can also specify the TCP port FostTexefOVR IP Ad ress 172 2 FastTracefDW Port Number 15020 No The ADPRO abeng defui IP address is 197 109 1 1 and the defaut port used by the Fastirace HLI 18029 W you we using the Presa HI to communicate hs FastTracefFastTx you must aiso configure the wet Trac Feet Tx Proscdium ings uang the D t line Mer Load Save ALL Settings Load from Fle E to Pile rre Settings oe Disconnect ADPRO Presidium Figure 58 High Level Interface Refer to the High Level Interface Manual available on the website www xtralis com adpro for details of the Presidium HLI operation Doc 12384_05 67 Installation and User Manual ADPRO Presidium by Xtralis 68 4 4 8 Security Tab Figure 59 Security Tab Access Secure Input Type The Access Secure input allows the Presidium to be independently set into the Access state of operation This input is usually connected to an alarm panel or access control system Refer to Access Secure Input on page 38 for more information 1 Select the type of the Access Secure Input Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resistor
27. other equipment connected to the CCTV system from potentially hazardous voltages that may appear on the cables that connect the video cameras to the Presidium To ensure the integrity of the protective earth that is provided via the grounded AC power outlet Presidium is fitted with an earthing grounding screw located on the top right corner of the rear panel The Presidium earthing grounding screw must be connected to a suitably grounded object such as rack frame or metallic water pipes using wire with a minimum of 2 5 mm cross section area 3 5 Video Connections 3 5 1 Inputs Figure 24 shows the video connections to Presidium The video output of a camera is connected to a Video In BNC type connector which may be terminated in 75 ohms software controlled at setup time The camera should be terminated unless the camera is teed off the video input to another device Each Presidium VM15 Video Module has two video inputs Video A In and Video B In Up to 10 VM15 Video Modules may be installed into a Presidium making a total of 20 video movement detection channels per unit Presidium Mini has two Video In connections Video A In and Video B In available Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual VM15 Video Module ALMA OP Alarm A Output ALM A ISOLATE Alarm A Isolate ALMA I P Alarm A Input GND Ground ALM O P COM Alarm Output Common ALM B O P Alarm B Output ALM B ISOLATE Al
28. site conditions should occur as a minimum These conditions can impact on the performance of Presidium or the level of security provided but are by no means an exhaustive list If a very significant change occurs then a site re evaluation may be required to ensure optimum performance Foliage can impact Presidium in a number of ways and must be kept controlled so that the following scenarios do not occur Masking areas where detection should occur Causing nuisance alarms where foliage has grown to be visible in the field of view Blocking lighting of areas during the night Removal of foliage causing changed lighting conditions such as removal of shrubs along a fence line allowing multiple vehicle headlights to sweep across a camera s field of view Moving shadows from wind blown foliage in the field of view of the camera causing nuisance alarms Lighting is an essential element of the performance of Presidium Lighting should be checked to ensure that all areas are adequately lit at all times and in particular structures or foliage are not blocking lights There are other environmental factors that can impact on the performance of Presidium or the level of security provided These include Changes to adjacent premises such as the erection of temporary or permanent structures can alter lighting provide a path for intruders to access the site or change activity levels expected around the site Changes within the prem
29. state at all times and access is controlled at the FastTrace FastTx FastTrace R refer to Access Secure Input Type on page 68 Note When connecting a FastTrace FastTx FastTrace R to a Presidium each FastTrace FastTx FastTrace R video input must be directly connected to a Presidium video output Hence if the Presidium has 20 channels a 20 channel FastTrace FastTx FastTrace R is required to operate all 20 channels If the FastTrace FastTx FastTrace R has not been previously configured refer to the unit s Installation and User Manual for the complete configuration procedure If the FastTrace FastTx FastTrace R has been previously configured refer to the procedure below to add the Presidium 1 Connect the FastTrace FastTx FastTrace R to the Presidium as shown in Figure 69 2 Connect the PC to the FastTrace FastTx FastTrace R via the Presidium Setup port on the front panel of the Presidium Note The PC must have VideoCentral installed refer to the FastTrace FastTx FastTrace R Manual for details 3 Access the FastTrace FastTx FastTrace R Installer Menu as detailed in the following section 78 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 5 1 Entering the FastTrace FastTx FastTrace R Setup Screen Remote programming of ADPRO video transmitters is carried out via a screen as shown below To start the programming operation connect to the attached FastTrace F
30. unselected part of the detection area The Darken Image checkbox increases the visibility of the detection area lines When a Trigger Area is selected using the right mouse click an option will be present in the drop down list to duplicate the current selected shape including properties Using this option may decrease setup time when requiring multiple Trigger Area shapes that are simular in shape and properties Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual The following figure defines the Logic used to generate VMD alarms It is important to note that Trigger Areas require 2 events before an alarm is generated Detect Movement Is movement within a Detection Area No Alarm Generated Is the movement a valid target Valid targets meet criteria defined in the Detection Parameter Screen Are any Trigger Areas Programmed Two events need to occur BEFORE a trigger area can generate an alarm Examples are A Target track crosses TWO edges in the correct direction B The target track crosses one edge and the Trigger Delay timer expires C The target crosses an edge and the disappears Have TWO trigger events occurred External alarm input active during VMD activity Alarm Input AND VMD Is external alarm input enabled ALARM Figure 50 Alarm Logic Doc 12384 05 59 Installation and User Manual ADPRO Presidium by X
31. 60 seconds 2 Once all settings are complete select Next The following screen is displayed 64 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Figure 54 Video Monitoring Video Monitoring Video Monitoring enables the generation of an alarm when the video signal is tampered with or a camera develops a fault Contrast Monitoring The Contrast Monitoring feature is provided as a check that the contrast of the camera image is acceptable The settings allow detection of unusually low contrast levels A contrast level indicator may be displayed on the video output refer to Display All Tracks on Video Output on page 54 for instructions A contrast alarm is triggered if low contrast is detected in a larger percentage of the image than specified in the Contrast Threshold 96 Note The contrast must be below the threshold for the entire duration defined in the Minimum Time to Cause Activation setting for a contrast alarm to be generated A low contrast alarm will be generated for both the following situations the camera is bagged by placing an opaque material over the lens causing the image to go dark the camera has a very bright light shone into the lens causing the image to flare and whiteout Note A contrast alarm will not be generated if the channel is isolated No Video Detection When checked Presidium will generate an alarm in the event of lost video on this camera channel
32. R Illuminator optional Figure 10 Camera PIR Mounting Details 16 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual The difference in dead zones of the two technologies is an important factor to consider when the PIR camera combination is used The PIR may have a very steep downwards angle whereas a camera may have a much larger dead zone as illustrated below This is a very important consideration as a moving target in the camera s dead zone may activate the PIR The target will not be visible to the camera mounted with the PIR however the target will be visible to the camera covering the first camera s dead zone If the PIR camera dead zones require matching carefully check the comparative dead zones to ensure that this can be achieved Also consider mounting the PIR and camera on separate poles PRO Detector A Difference in Dead Zones Camera Dead Zones Figure 11 Camera PIR Dead Zone Comparison The installation and use of any detection technology should consider The angle of elevation and the horizontal alignment with the camera is critical in providing a high degree of performance It is recommended to keep foliage trimmed and grass cut for a clear PIR and camera FOV e Termination barriers are important so that targets past the protected area are not detected Minimise reflective material in the FOV to ensure reflections from sunlight do not affect the PIR Minimise facing PIRs in the
33. This will minimise the number of nuisance alarms In each detection area check that detection does not occur in areas that are masked out or should not be aligned with PRO series PIRs or other detection technology 4 6 2 IP Address Forgotten If the Presidium appears in the list of local units on the Establish Connection page refer to Connect to an Presidium on page 47 highlight the Presidium and select the System Info button The IP Address and Subnet Mask are displayed 4 6 3 Presidium Will Not Connect Presidium Appears in List of Local Units If the Presidium appears in the list of local devices on the Establish Connection page refer to Connect to an Presidium on page 47 but will not connect 1 Ensure that the PC and the Presidium have correct IP addresses assigned and that the subnets match If the PC has a static IP address on a different subnet to the Presidium they won t be able to connect refer to Configure the PC Network Connections on page 45 Doc 12384 05 73 MINI 74 Installation and User Manual ADPRO Presidium by Xtralis 2 Select the System Info button to display the Presidium s IP address and subnet Presidium Does Not Appear in List of Local Units If the Presidium does not appear in the list of local units 1 Ensure that the connected PC has a compatible IP Address This may be performed by following the procedure on page 45 Configure the PC Network Connections 2 Restart the Presidium Setup Uti
34. Trace Fails to Operate Ensure the IP Address and Port Number programmed within the Presidium High Level Interface HLI match the respective details within the FastTrace After programming and the physical network connection has been completed re power both the FastTrace and the Presidium to restore the connection 4 6 6 Presidium Setup Utility cannot be Started If the Setup Utility is closed incorrectly it will be left in a state where an error dialog will appear when trying to restart The error dialog box may indicate the Setup is already running To rectify this problem using Windows Explorer navigate to the installation location The default is C Program Files ADPRO Locate the file called Setup Utility 1 0pSU lock and click DELETE The Setup Utility should now start correctly Doc 12384 05 75 Installation and User Manual 76 ADPRO Presidium by Xtralis Doc 12384_05 Installation and User Manual 5 Connection to ADPRO FastTrace FastTx FastTrace R by Xtralis ADPRO Presidium by Xtralis uinipisaig Aq poje1ouob suueje 40jluoui 0 pasn ejue2 oapiA g 10jeodo uinipisaig Aq poje1euoB suueje 10juoui 0 pasn eua oopiA z 10je19dO A Vi SHOMION E S uunipisaig Aq payeiaueb swseje 40 UOW 0 pasn Eu O9pIA 10j amp 19d uinipisaig Aq poje1ouoB suueye 10juoui 0 pasn jeua oapiA v 10je19dO jejpuer uorsses JNO saunbal Serien is JO pesn osje j sed 310M SN seBeuu 19jutd So1y
35. a Bi SPECifi CATIONS ec Appendix A False and Nuisance Alarms eese nennen inte nr nin nens Appendix B Site Survey Checklist eese sese esie ea nennen nenne nnnn nn tante th nan nnn Appendix C Example Site Plan 4 eeseseseeeseeeeeee ei EEERR ENER EEEEE REESEN ENEE REENEN nan nnns Appendix D System Design and Equipment Checklist eee Appendix E Camera Lens Selection eee esie eren ense en nenne tenni tht ne nhan tnn Appendix F Commissioning Checklist eese ereeese cessere eee enne nnn nnn nn then tranne Appendix G Site Detection Tests esses EEEEERREE EE s eeenen NEE annnm nnn neri tane nn tenants Appendix H Site Maintenance Tables esee esee sese sensere nnne nnn nnn nnn tren nena nnns Appendix I Installation Quick Reference eeeesseeeserse seien eenee ener nnne then nhan nns Appendix J Presidium Do s and Dont ts eese essen ener eenne nenne nnne nin nn nr rnnt Doc 12384 05 Installation and User Manual 91 93 95 97 99 101 103 105 107 109 Installatio n and User Manual List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17
36. al 7 Adding a VM15 Module Extra VM15 Video Modules may be retro fitted to provide a maximum of 20 channels per Presidium Caution ADPRO Presidium system components contain electrical parts that are susceptible to damage from static discharge Static voltages of one to thirty kilovolts are common in unprotected environments When installing or servicing Presidium equipment it is advisable to observe the following standard precautions for handling electronic assemblies to reduce the risk of component damage Minimise handling of electronic assemblies and components Transport temporarily arrange and store electronic components in recognised anti static containers Discharge any static voltage from your body before handling electronic components or wear a grounded Safety Standard Approved anti static wrist strap while handling components Avoid handling electronic components in areas which have a floor or work surface capable of generating a static charge To add a VM15 Module 1 Ensure that the Presidium is switched off and all power is removed 2 Remove the 10 screws securing the lid to the top of the Presidium retaining the screws 3 Remove the blanking plate from the slot where the new module will be inserted retaining the screw Note The module must be inserted into the next blank space i e closest to the mains power connector 4 Insert the module ensuring correct polarity and that the pins are no
37. and User Manual ADPRO Presidium by Xtralis 32 3 3 Power Connection 3 3 4 Presidium Presidium is designed for 100 240 VAC 50 60Hz operation It should not share electrical outlets or circuits with devices that may cause significant electrical interference such as air conditioners or a photocopier Some installations may have particularly bad mains power disturbances such as large voltage spikes surges and power sags which may cause system failure In this case power line filters conditioners and or uninterruptible power supplies should be fitted between the Presidium and the mains As with any electronic equipment to ensure long term reliability it is advisable to mount the Presidium clear of other equipment which may dissipate large amounts of heat and ensure adequate convective air flow between the Presidium and its surroundings 3 3 2 Presidium Mini The Presidium Mini is designed for regulated 12V DC operation The recommended method of obtaining this power is from the supplied plug pack unit via 100 240 VAC 50 60Hz operation Alternatively the DC power may also be supplied from a suitable 12V battery source with fuse protection 3 4 Earthing Screw IEC 60950 1 the relevant product safety standard for Presidium classifies the CCTV systems that Presidium is typically used in as Cable Distribution Systems The integrity of the Presidium protective earth must be ensured This is to protect service persons and users of
38. and programmed correctly Adjust the Detection Sensitivity as required refer to Detection Sensitivity on page 60 It may be necessary to increase the sensitivity The sensitivity may be customised refer to Customise Sensitivity on page 61 Adjust the Environment Activity as required refer to Environmental Activity on page 60 Each Presidium channel may be isolated which will prevent any alarms from being generated by that channel Ensure that the channel is not isolated The Presidium must be set to Secure for detection to occur Check that the physical input to the Presidium is in the Secure position refer to Access Secure Input on page 38 To perform detection diagnostics select Display all Tracks on Video Output General Setup on page 54 this displays all movement that the Presidium is detecting in the detection area This may be used to ensure that all movement is being detected Note It is not recommended to enable this function during general use of the Presidium It should only be used as a diagnostics tool when setting up or fault finding the Presidium Note The Presidium Setup utility must not be connected to the Presidium during normal operation The setup utility should only be connected when programming or changing settings All VMD detection is temporarily disabled when the Setup Utility is connected It is also important to check that detection is not occurring in areas in which detection should not occur
39. arm B Isolate ALM B I P Alarm B Input Figure 24 Connection to the VM15 Video Module In order to synchronise to the incoming video from the camera and to avoid reduced performance of the video movement detection the following conditions must be met the sync amplitude atthe Video Input of each VM15 Video Module must be within the range of 0 2 V to 0 4 V and the video amplitude not including sync at the Video Input of each VM15 Video Module must be within the range of 0 5 V to 1 0 V If the video level at the Video Input is poor cable compensators or video line drivers should be installed at the camera end This boosts the video signal to within the voltage limits given above A video contrast level indicator may be displayed on the Presidium video output if required to assist with setting the video contrast levels Refer to Display All Tracks on Video Output on page 54 for more information 3 5 2 Outputs There are two video outputs on each VM15 Video Module and on Presidium Mini e Video A Out and Video B Out The video outputs provide standard composite video signals when driving 75 ohm loads In the event of a power failure at the Presidium the video input signal is passed directly through from the video input to the video output Doc 12384 05 33 Installation and User Manual ADPRO Presidium by Xtralis The following table details graphics that are displayed on the video outputs Table 2 Video Outpu
40. as of a camera s field of view will generate a motion detection alarm To reduce false alarms areas of a camera view that contain trees roads etc should if possible be excluded from detection or trigger areas Add Detection Shape A Detection Shape is a special area graphical shape placed onto a camera view that is sensitive to target motion within its boundary lines The parameters used to define and measure motion of a target within a Detection Shape are defined by the Detection Parameters see section on page 60 and all detection parameters must be satisfied before a alarm event can be triggered Targets outside of a Detection Shape are ignored Click on the Add Detection Shape button or right click in the image to place a new detection area on the image The detection area is shown in red and is presented with four nodes Use the mouse to move the position of the nodes to change the size and shape of the detection area To add more nodes select a boundary line and press the Add Node button or right click on a line segment To remove nodes select Remove Node button or Right Click on a node To remove an entire shape select a shape and press Remove Shape or right click on a shape Add Trigger Shape A Trigger Shape is a special area placed within a Detection Area A Trigger Shape is sensitive to target track motion across its boundary lines The user can select the particular type of target action ie direction that must occur to
41. ass through two edges to generate an alarm Note The default trigger area needs to be programmed by defining edge properties and area properties before it will detect target activity Doc 12384 05 57 Installation and User Manual ADPRO Presidium by Xtralis 58 Trigger Area Properties V Trigger Area Properties Name Trigger Area C Detect Appearance go Detect Disappearance C Enable Timer Trigger Delay in Seconds Figure 49 Trigger Area Properties Trigger Areas can be given a unique Name to assist with identification Attached to each trigger area are options to Detect Appearance Select this option if an alarm is to be generated when a target appears but has not entered the trigger area by crossing an edge Detect Disappearance Select this option if an alarm is to be generated when a tracked target disappears from the trigger area for example hides behind a pillar or stops moving Enable Timer By selecting the Enable Timer option a value of 0 to 180 seconds can be entered as the Trigger Delay in Seconds A timer delay of 0 seconds will cause an alarm to be generated as soon as a target track crosses an Entry or Crossing edge A value of 1 180 seconds defines the maximum time a target track can remain within the trigger area before an alarm is generated The entire field of view of a Detection Area may be selected using the Select Entire Area button The Invert Active Region checkbox selects the previously
42. assis Access secure MODE input to enable disable detection on all channels Screw terminal connectors Normally Open NO Normally Closed NC Single End of Line SEOL or Dual End of Line DEOL tamper detection on each input using supplied resistors Outputs per channel 2 channels per module or Presidium Mini Alarm output relay activates on the occurrence of an intrusion alarm Can also be programmed to activate on a no video and or contrast alarm Outputs per chassis 1 general alarm relay normally open and normally closed contacts activates when an alarm condition occurs on any module standard Presidium only 1 fault relay normally open and normally closed contacts activates on the occurrence of any system fault power loss over temperature condition system reset Network Connections Setup Port Front Panel on standard Presidium and Rear Panel on Presidium Mini 10BaseT 100BaseT Ethernet Port supporting TCP IP LAN 1 amp 2 Rear Panel standard Presidium only Both 10BaseT 100BaseT 1000Base T Ethernet Port supporting TCP IP Used for HLI connection to FastTrace FastTx FastTrace R and remote network connection Setup Setup via an intuitive PC based utility that connects to the unit via a network connection Power Requirements 100 240 volts AC 47 63 Hz Maximum power dissipation 250W Presidium Mini 11V to 16V DC Maximum power dissipation 18 W Universal AC Power Adaptor su
43. astTx FastTrace R and click on the Installer Menu button behind the Site Actions button in the main VideoCentral User Interface GUI l x Live Review Figure 70 Installer Menu Icon Note Only operators logged on to the system either as Administrators or Installers have access to this icon Users defined as Operators do not have access to this function If this icon does not appear or appears greyed out log out the current operator and log on a new operator with the correct access rights The current settings within the FastTrace FastTx FastTrace R will be downloaded to the VideoCentral system and the following typical screen will appear Note that FastTrace R transmitters have some options disabled FastTrace User Settings Category Site Details past Date Time Settings Licensing P73 BUILD Communications Call List Connected Equipment FT1111 Cameras Monitor Transaction Devices FT2222 Transparent Data Port Alarm Inputs Presidium Inputs Copyright Details Control Outputs Version p 3setup axiom2 Build 0001 Audio Arming Disarming Aneratinnal Rehavinwr gt Observer Password CMS Password Copyright Copyright 2007 by Xtralis Information and Help Basic information about the site for ideo Central to be able to access it Matching details must be entered into the Video Central Database Save to File Load from File Discard all changes Figure 71
44. be used in conjunction with other detection technologies The respective maintenance and testing procedures for the other products should be used in conjunction with this information to ensure overall site security is maintained at the required level Maintenance of the PRO series of PIR detectors is also covered in this section To perform maintenance in a repeatable and consistent manner it is suggested that a table of tests and checks to be carried out in each inspection maintenance cycle be drawn up which should have been done as part of the commissioning phase This will ensure that the system is tested in a similar fashion each time particularly if sufficient detail is provided for each test These tables should include the following information for each camera PIR and or detection area Date Time Person conducting tests Description of test or maintenance to be performed Results of test or maintenance performed Highlight any maintenance or site issues to be addressed Date Time for next maintenance test In addition copies of site plans annotated showing camera locations as well as location of any other detector technologies should be used to document detection areas and the path of detection tests Site Maintenance Tables on page 105 contains examples of tables for tracking maintenance procedures and outcomes 2 8 2 Routine Site Maintenance Regular site inspections preferably on monthly basis that check the listed
45. by Xtralis Installation and User Manual Table 4 Network Connection Indicators Link Status Network Speed LED Displays 10 100 1000 LAN1 Down Any All LEDs off and LAN 2 ports on rear panel UP 10 Mbps RH Dual coloured speed LED OFF LH Green Activity LED LINK ACTIVITY ON if link up or flashing if link up and data transfer activity MINI UP 100 Mbps RH Dual coloured speed LED GREEN LH Green Activity LED LINK ACTIVITY ON if link up or flashing if link up and data transfer activity UP 1000 Mbps RH Dual coloured speed LED Yellow LH Green Activity LED LINK ACTIVITY ON if link up or flashing if link up and data transfer activity 10 100 SETUP Down Any All LEDs off port on front fascia MINI UP 10 Mbps LH GREEN LED OFF IR RH GREEN LED LINK ACTIVITY ON if link up or flashing if link up and data transfer activity UP 100 Mbps LH GREEN LED ON RH Green LED LINK ACTIVITY ON if link up or flashing if link up and data transfer activity Note ALWAYS consult with the IT or Network Manager for the network BEFORE physically connecting Presidium to the network 3 11 Status LEDs The are two LEDs displaying the unit s condition Power and Status Power LED The Power LED illuminates green when power is supplied to the Presidium Status LED The Status LED illuminates red when a fault has been detected in the Presidium the fault relay is also activated or during bootup Th
46. by causing interference on the video signal i e the picture displayed on the monitor During the design stage it is important to consider the likelihood of interference from high voltage or ground loops and factor counter measures into the design such as floating earths and isolation transformers on video signals Installation Adjacent to Roads Headlights sweeping across the area under surveillance have the potential to cause nuisance alarms If the area is near a road and has the likelihood of headlights sweeping over it consider some sort of light barrier to ensure the headlights do not cause nuisance alarms The options for light barriers includes a solid panel such as plastic or metal facades placed on fences next to the road high opacity shade or greenhouse landscaping cloth or privacy mesh interwoven on chain link fences 2 6 2 PIR Installation Alignment Aligning the PIR with the camera is critical for good performance There are a number of ways of checking PIR alignment A slot in the top of some of ADPRO s range of PIRs can be used as a simple method to align the PIR Looking through a drinking straw into the slot or resting a laser pointer in the slot can be used to help with alignment ADPRO offers an alignment telescope for aligning PIRs across the full range A cordless walk tester CT 45 is available During a walk test it indicates a detector alarm with a beeper and an LED In addition a tester and softwa
47. c udo ta a e REN nud cni catione n te PER 21512 SIG HIEN ee tte pet e do oO eds red aen fO EAE Detailed Site Plan EEN EEN Site Images Clarify Requirements EODEM 2 5 3 System Hardware Camera Selection and Location EE Other Detectors Selection and Location sess PIR Ahonmemt enana WC le WEE Camera PIR Alignment Illumination Requirements EQUIPMENE ROOM os iie adi ee A IR Rede Ree e Re io a RAM ERR Monitoring Equipment eire a e eet cb aee RE qe rea dto restos 2 6 System UE EE 2 64 Gamera Installation re eet Ee pentes ele e uode dette een E E e ats Alignment Installation Hints Installation and User Manual N oL o DOONNNNND DOO THUY Bb RROUoOoO0O w Interference Caused by High Voltage c or r Ground Loops Installation er ae tO HOadS eom acera ret eee ta ene e RT ee ri a s 2 6 2 PIR Installation Alignment 2 6 3 Instrument Racks and Cablings E 2 7 Site Commissioning aie tates ne 2 7 1 Presidium Configuration 2 7 2 Performance Assessment Detection RK Soak Tests 2 7 3 System Tests oe PE AA AE ed ecd aee Gag E e 2 7 4 Recording System Configuration EE Doc 12384_05 Installation and User Manual ADPRO Presidium by Xtralis 2 8 Site Maintenance EE 2 8 1 Routine Maintenance EE 27 2 8 2 Routine Site Maintenance e nnn OD 2 8 3 Routine Equipment Maintenance eee eene ener 28 2 8 4 Routine
48. cessfully transmitted to the Central Monitoring Station If functions such as Access Secure are being used within Presidium test that the behaviour meets expectation and the system generates alarms when it is armed If the Presidium is integrated into a larger matrix or CCTV system ensure that any inputs outputs to from the larger CCTV system function as expected 2 7 4 Recording System Configuration Once all the Presidium channels have been configured the configuration details should be saved Selecting the Save to File button on the Presidium Setup screen will cause all settings currently within the software to be saved to the PC a confirmation box will be presented to verify the required action This enables the complete configuration to be saved This may then be reloaded in the case of a system malfunction or used to configure another system The configuration is saved as a settings file in a user defined location on the PC Selecting the Load from File button enables the saved configuration to be uploaded to the connected Presidium 2 8 Site Maintenance This section covers the following five areas of system maintenance and management Routine Maintenance Routine Site Maintenance Routine Equipment Maintenance Routine Detection Tests Maintenance to Regulatory Requirements Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 8 1 Routine Maintenance On many sites Presidium will
49. ck on the Presidium Setup Utility icon on the PC desktop The following screen is displayed V Presidium Setup Utility Establish Connection To establish connection follow these simple steps 1 Configure your computer with an IP address of 192 168 1 2 and a subnet mask of 255 255 255 0 in the Network Connections control panel 2 Using the supplied network cable connect your PC to the Setup Port of the Presidium 3 Walt up to 60 seconds for a device to appear in the lst below 4 Select a device from the list and press Connect 9 Select from List of Local Units Auto Detected ADPRO Presita To connect to a device on a remote network enter the network address and port of remot below O Enter Network Address IP Address or Host Name IP Adress Pert Connect ADPRO Presidium Dresda Sano Lely Verson 0100 00 Figure 38 Establish Connection to the Presidium Presidium standard 1 Enter the IP Address or Host Name and Port Number of the Remote Network Select the Connect button Note Port 80 is used as the default The number can be changed in the Setup Utility to a valid number between 80 and 65535 excluding 88 and 20001 to 20004 W Presidium Setup Utility Establish Connection To establish connection follow these simple steps 1 Configure your computer wih an IP address of 192 160 1 2 and a subnet mask of 255 255 255 0 n the Network Connections control panel 2 Using he supplied network
50. cribes a typical installation scenario for a medium security Presidium system To provide a high security installation where the intrusion is expected to be covert detailed consultation with Xtralis staff is required 2 1 2 Scope The following items are addressed in this Design Guide Presidium Operational Background Site Survey and System Design Equipment Installation System Commissioning Site and Equipment Maintenance The following items are not discussed in detail in this guide Design installation configuration or maintenance of complementary detection technologies excepting PIRs supplied by ADPRO refer to other manufacturer s technical and application information Installation or configuration of ADPRO FastTrace ADPRO FastTx or ADPRO FastTrace R refer to the FastTrace FastTx FastTrace R Installation and User Manuals Installation or configuration of Xtralis s ADPRO VideoCentral Monitoring Software refer to Central Monitoring Station Design Guide Part No 201700 Any relevant Application Notes Tech Tips and FAQs Refer to Xtralis website www xtralis com 1 Human like a feature that is able to differentiate between human and non human movement for intru sion detection Installation and User Manual 2 1 3 Intended Audience ADPRO Presidium by Xtralis The intended audience for this Design Guide includes the following key stakeholders Security Consultants System Integrators
51. ction area and press Update Image 2 Drag line A over the object adjusting the horizontal bars to extend from the top to the base of the object Ensure that the object is larger than the minimum height to which the line may be adjusted 3 Enter the height of object A in the Height of object A box Note An indicator of the position of object A should be retained to enable the distance between object A and B to be measured 4 Position a person or object in the background of the detection area and press Update Image 5 Drag line B over the object adjusting the horizontal bars to extend from the top to the base of the object Ensure that the object is larger than the minimum height to which the line may be adjusted Enter the height of object B in the Height of object B box Enter the distance between the base of the two objects in the Distance between base of each object C box NO Note The greater the distance from foreground to background of the two objects the more accurate the camera calibration will be This is because small inaccuracies in measurement are less significant over larger distances Note The Darken Image checkbox increases the visibility of the calibration lines 8 Select Next The following screen is displayed Figure 48 Areas 56 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Areas Defining the detection and trigger areas for a camera determines which are
52. d and All Tracks selected refer to Display All Tracks on Video Output on page 54 All active tracking information is displayed Pre and post alarm tracking is distinguished using colour Any movement real or imagined is tracked This mode is primarily for diagnostics 34 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 3 6 Alarm Inputs There are two alarm inputs one per channel on each VM15 Video Module and two in total on Presidium Mini They are labelled ALM A I P and ALM B I P The alarm inputs may be used to connect PIRs etc to combine with the video motion detection by ANDing or ORing to generate an alarm A triggered alarm input may be configured with a hold time from 0 to 60 seconds for alarm generation with VMD refer to Alarm Behaviour on page 63 To ensure the best immunity to EMC disturbances the alarm inputs should be wired using shielded cable Connect the shield to the ground GND terminal VM15 Video Module p Camera 20 PIR to alarm input ALMA O P Alarm A Output ALMA ISOLATE AlarmA Isolate ALMA I P Alarm A Input GND Ground ALM O P COM Alarm Output Common ALMB O P Alarm B Output ALMB ISOLATE Alarm B Isolate ALMB I P Alarm B Input Figure 25 PIR Connections VM15 shown The Alarm Input state may be Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resis
53. degradation is minimised from the outset The quality of the video is influenced by the cable length Generally the shorter the cable runs between the Presidium and the camera better the quality of the picture For long cable runs cable compensators may be required A video contrast level indicator may be displayed on the Presidium video output if required to assist with setting the video contrast levels Refer to Display All Tracks on Video Output on page 54 for more information Doc 12384 05 11 Installation and User Manual ADPRO Presidium by Xtralis 12 2 Camera Field of View FOV Setting the correct horizontal FOV of the camera is critical for reliable detection The horizontal FOV determines the lens required on the camera The following guidelines are important Ensure there is adequate detection area The minimum detection area requirement is 6m 19ft width i e if there is only a 2m 6ft gap between a building and a fence then reliable detection will not be possible Ensure that the horizontal FOV at the maximum detection range does not exceed the recommended maximum of 25m 82ft The tilt of the camera should be such that the FOV does not include large areas of the sky thereby reducing the detection area of the Presidium system Ensure the FOV is clear with minimum views of foliage and obstructions that provide cover for intruders Presidium uses perspective compensation for its motion detection algorit
54. dered for offsite response identify the location of any noisy equipment e g generators to ensure that any microphones to be installed will not be affected by the noise This also relates to onsite audio broadcast equipment i e speakers and horns should be appropriately located and specified with appropriate power Site Images Collect a detailed set of site images covering all protected areas The site images provide a visual reminder when assessing the site plan offsite These also provide a reference point during installation and commissioning Ideally the digital images should be taken under a variety of lighting conditions i e dawn daylight dusk and night The most challenging lighting conditions for CCTV systems can occur at dawn and or dusk It is vitally important to be aware of the variable lighting conditions under different circumstances and in different seasons The detailed site survey must consider the likely occurrence of seasonal variations Shedding or sprouting of new leaves on nearby trees may affect lighting conditions and camera views Ideally there should be no trees in any camera views however this is not always possible Lighting and views change as foliage grows or drops affecting nuisance alarm rates or detection probability The following images illustrate some suitable and unsuitable perimeter and area protection scenarios for a Presidium system 8 Doc 12384 05 ADPRO Presidium by Xtralis Installation and Use
55. desg uonejs e3ue2 DSWD 193nduio5 uonejs Buuojuoy je3ue2 E I IND dnjes winipisasg pue unipisaJd Aq paje1ouob suueje 40 UOW 0 pasn Eu O PIA SE Bur66o0 49jul4d au uod woo ZEZSH AUN eus 10M9N oz eweg eesse 0 suere je spues IH Ps o 000000000 00000900 ats OGD SEES EE uopeogunwwog iE SE E Lee eose1jpjse4 OUdQv UinipiSeJg WOM og Bno pedoo ep L EN D A nipisaJd OYdAY Aue2o Dosen Ind dnjes T aus ajoway Figure 68 Complete standard Presidium Installation 77 Doc 12384_05 Installation and User Manual ADPRO Presidium by Xtralis Setup GUI N RS used locally E mm S m S Mos ens NDA BN Setup GUI used remotely can be on the same PC as Video Central Video looped through 20 from Presidium FastTrace Network ADPRO FastTrace an e ENS wand p Bex alarms generated by Presidium HLI sends all alarms to FastTrace Figure 69 Typical Connections to a standard Presidium Note Before connecting the FastTrace FastTx FastTrace R to the Presidium ensure the Presidium setup has been completed refer to Configure Presidium on page 47 Note Ensure the Access Secure input is set in the default state of Normally Open and that nothing is connected to this input This ensures the Presidium is in the Secure
56. direction of sunrise or sunset e PIRs also require a maintenance program to clean the lenses and to regularly check performance and alignment PIR Alignment For good PIR performance ensure PIR and camera alignment match The following figure shows the optimal PIR placement angle where the top of the curtain is approximately 1m 3ft high at the maximum detection range PRO Detector Figure 12 Optimal PIR Angle When using a long range PIR next to a fenceline it is important that the PIR curtain is aligned approx 0 5m 2 ft inside the fenceline as shown in the next figure Doc 12384 05 17 Installation and User Manual ADPRO Presidium by Xtralis Camera Dead Zone PIR Curtain Camera Field of View Fenceline Termination Board Figure 13 PIR Alignment on Fenceline PIR Termination If PIRs are being used on the site then their detection curtain must be terminated suitably ina similar fashion to blocking out lights from nearby roads Referring to Figure 15 under the PIR alignment section the detection curtain should be terminated by a suitable material at the boundary of detection Suitable materials include privacy mesh that can be woven into chain link fences plywood heavy landscaping cloth or plastic facades The use of steel is not recommended as it may heat to a temperature that a PIR may incorrectly detect as a human body Figure 14 Example PIR Barrier 18 Doc 12384_05 ADPRO Presidium by Xtra
57. duct documents available from Xtralis All proper health and safety precautions must be taken during the installation commissioning and maintenance of the product The system should not be connected to a power source until all the components have been installed Proper safety precautions must be taken during tests and maintenance of the products when these are still connected to the power source Failure to do so or tampering with the electronics inside the products can result in an electric shock causing injury or death and may cause equipment damage Xtralis is not responsible and cannot be held accountable for any liability that may arise due to improper use of the equipment and or failure to take proper precautions Only persons trained through an Xtralis accredited training course can install test and maintain the system Liability You agree to install configure and use the products strictly in accordance with the User Manual and product documents available from Xtralis Xtralis is not liable to you or any other person for incidental indirect or consequential loss expense or damages of any kind including without limitation loss of business loss of profits or loss of data arising out of your use of the products Without limiting this general disclaimer the following specific warnings and disclaimers also apply Fitness for Purpose You agree that you have been provided with a reasonable opportunity to appraise the products and have made your o
58. e This appendix provides a quick reference guide for installation of a Presidium system Camera Alignment Align the camera as described in the site design plan documentation Test the alignment by measuring the FOV at the near range and the maximum range PIR Alignment Align the PIR as described in the site design plan documentation Test the alignment by a manual check or using test software to confirm detection Set Detection Areas Set the detection areas on each camera on Presidium to mask out any unwanted areas that are unavoidably within the FOV of the camera i Program Detection Parameters Program the detection parameters in each Presidium channel Use the suggested typical settings as described in this document and adjust later as required Test System Perform walk run tests in each detection area to check that the Presidium PIR is functioning as expected Alter parameters as required to achieve detection reject nuisance alarms and retest as appropriate Save the final configuration for all channels Doc 12384 05 107 Installation and User Manual ADPRO Presidium by Xtralis Maintain System Perform routine maintenance on the system to ensure that detection still occurs as initially planned and the nuisance alarm rate is at a minimal level Take remedial action if the system is not functioning as required 108 Doc 12384 05 ADPRO Presidium by X
59. e Listener Port Number defines on which port the Presidium High Level Interface communicates with the FastTrace FastTx FastTrace R Warning Note 5 4 It should not be necessary to change the port number on which the Presidium High Level Interface communicates with the FastTrace FastTx FastTrace R Do not change this setting unless instructed by Xtralis technical support Ports 15020 to 15029 are valid for connection to the Presidium This setting must be the same port as that selected in the Presidium Setup Utility High Level Interface tab refer to High Level Interface Tab on page 67 IP Address Requirements Once the Presidium and the FastTrace FastTx FastTrace R have been configured it may be necessary to change the IP Addresses to suit the network requirements Note Doc 12384 05 When choosing the FastTrace FastTx FastTrace R and Presidium IP addresses itis important to ensure no other devices on the network are using those IP addresses Ask your network administrator if you are unsure what IP addresses can be used 83 84 Installation and User Manual ADPRO Presidium by Xtralis Example IP Addresses If the FastTrace FastTx FastTrace R IP address is 192 168 5 10 and the subnet mask is 255 255 255 0 a compatible Presidium IP address would be anything starting with 192 168 5 x e g 192 168 5 11 The Presidium subnet mask should then be set to 255 255 255 0 The FastTrace DVR IP Address
60. e Presidium Mini also has 2 additional LED indicators to display which channel is in alarm Doc 12384 05 41 Installation and User Manual 42 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual 4 Installation Configuration Before installing the ADPRO Presidium this section should be read thoroughly If any difficulties arise contact your supplier or Xtralis Pty Ltd directly 4 1 Unpacking After unpacking the Presidium carefully check for any signs of damage Any damage should be reported to your supplier or to Xtralis Pty Ltd directly before the Presidium is installed Check that the packing carton contains the following items 1 detachable power cord 1 regulated 12 V plug pack Presidium Mini only 1 I O screw terminal connector to connect to the I O connector fitted to the unit 1 EOL resistor pack 1 Presidium Quick Setup Guide 1 ADPRO Product Installation and Upgrade DVD 1 crossover Ethernet cable 1 fan cover to be fitted before powering unit standard Presidium only When supplied as a spare each VM15 module is supplied with 1 I O screw terminal connector to connect to the Alarm connector This connector will be plugged into each VM15 module 1 EOL resistor pack 4 2 Install Setup Utility To set up the Presidium for operation it must be connected to a PC installed with the Presidium Setup Utility The PC must also be configured with the requir
61. e detected the horizontal field of view should not exceed 25m or 20m for high security 2 5 2 Site Survey Once preliminary information is collected and the site considered suitable for protection with Presidium a site survey can be conducted Conduct the site survey taking into account any customer tender or requirements documents to ensure that the survey and subsequent design meet the customer s specifications and requirements The site survey draws on the preliminary information to design a complete system Determine all necessary criteria for the system and ensure all relevant information is collected Where clarification is required ensure that this is received from the customer or their representative Appendix B contains a checklist for a Site Survey The items required to perform a detailed site survey include 1 Digital Camera 2 Tape measure 3 Workbook and 4 Site Plans accurate engineering drawings of the site The different stages of a site survey are described below Doc 12384 05 7 Installation and User Manual ADPRO Presidium by Xtralis Detailed Site Plan The production of a detailed site plan annotated with key information refer to Appendix C for an example is the key element in completing a successful site survey As a minimum the following information must be included 1 Location and type of existing illumination including coverage to determine its suitability If necessary specify additional illuminati
62. e eene nennen mener en nnne enr renes 82 Figure 76 FastTrace FastTx FastTrace R Communications e El Figure 77 Advanced Communication Properties A OG Figure 78 Typical Connections to a Third Party DVD OD Figure 79 VM15 Module Inetallapon sess nennen mener nenne 87 List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 QUICK GUIDE cce ote ee e s Rok e eo estet 4 Video Output Display ege ode ee ted vit bec tee Dose deu eu OL Age 34 Fault Ftelayz addu ee NIS eee eh ARSON nc diet peste edid eame ciens 39 Network Connection Indicators sisse eee Al Video Motion Thresholds Explanation sse mmn O2 Presidium Specifications esses esee esee emen iaai neni sn rte senes 89 Horizontal FOV 20 Metres 66 Feet ene DO Horizontal FOV 22 Metres 75 Feet HEI Horizontal FOV 25 Metres 83 Feet HEI Table 10 Horizontal FOV 30 Metres 98 Feet 100 Table 11 Camera Maintenance Table uu ccc cece eccc eee eeeeceese cece 105 Table12 PIR Maintenance Table enr eee Ee SEENEN tenete 105 Doc 12384 05 Installation and User Manual ADPRO Presidium by Xtralis Doc 12384_05 M NI ADPRO Presidium by Xtralis 1 Installation and User Manual Introduction The Presidium Intelligent Video System is a high performance modular multi channel video movement detection system It is optimised for maximum protection
63. e which sequences through the three images to highlight movement Camera Behaviour Setup While the FastTrace setup allows any Presidium input to be associated with any camera they must be mapped one to one ie Presidium Input 1 to Camera 1 See Figure 75 as an example Doc 12384 05 81 Installation and User Manual FastTrace User Settings Category Monitor Transaction Devices Transparent Data Port Alam Inputs Presidium Inputs Control Outputs Audio Arming Disarming Operational Behaviour Operational Modes Audio Behaviour Camera Behaviour Multi Screen Live Behavior Entry Exit Behaviour Maintenance lt Information and Help Detine the behaviour for each camera connected to the unit Save to FastTrace Save to Fie Camera Behaviour Select Mode from list ADPRO Presidium by Xtralis 1 Front door gt Presidium Input Front door Camera Recording System Information Compression capacity in use for selected Mode 40 Recording Capacity available Days Load from File 0 Discard all changes Figure 75 Mapping the camera inputs 5 3 Advanced Communication Properties Warning It should not be necessary to change the port number on which the MINI Presidium High Level Interface communicates with the FastTrace FastTx FastTrace R Do not change this setting unless instructed by Xtralis technical support 1 Select the Communications option
64. eally there should be very little activity caused by car headlights trees etc in the background to avoid false alarms Please refer to the on screen descriptions for guidance on the setting to use based on the camera view Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual If a cluttered background scene is unavoidable it is recommended that motion detection be combined with another method of alarm generation e g PIR microwave detector or fence sensor Both motion detection AND the alarm input must be triggered before an alarm is generated This is configured on the next screen Alarm Behaviour Defining trigger areas can also be used to minimise nuisance alarms in these circumstances Please refer to the on screen descriptions for guidance on the setting to use based on the camera view Increased Sensitivity To increase the sensitivity of detection under constant lighting conditions tick the Increased Sensitivity check box Constant lighting usually refers to indoor locations where there is little change in the lighting level and contrast of a camera view Customise Sensitivity V Customise Detection Sensitivity Create Edit Remove custom detection sensitivities based on the video motion thresholds to the right Note You cannot modify the pre defined Low Medium and High sensitivities IMPORTANT If you modify a sensitivity the changes will apply to all channels using that sensitivity IF you o
65. ect Predis erg Utliry Vernon 01 00 00 Figure 37 Establish Connection to the Presidium 5 Wait for approximately 60 seconds for the connected device to appear in the List of Local Units if the Presidium is connected locally The default Presidium IP address is 192 168 1 3 and the subnet mask is 255 255 255 0 6 Highlight the required device and select Connect If the connected device does not appear in the list check the following Check the ethernet connection by ensuring the LEDs on the Setup port connector are illuminated refer to Table 4 on page 41 If the connected device appears in the list but will not connect Ensure the PC and Presidium subnets match If the PC has a static IP address on a different subnet to the Presidium they won t be able to connect refer to Configure the PC Network Connections on page 45 Select the System Info button to display the Presidium s IP address and subnet 7 Once the connection to the Presidium is established the Password screen is displayed refer to Section 4 4 3 Doc 12384 05 47 Installation and User Manual ADPRO Presidium by Xtralis 4 4 1 2 Remote Connection 1 Ensure the fan cover is fitted to the front of the Presidium standard Presidium only Use the supplied crossover Category 5 Ethernet cable to connect the PC s network port to the Setup port on the front panel of the Presidium Ethernet port on Presidium Mini 3 Power on the Presidium 4 Double cli
66. ections to a standard Presdum nesr iettt nest nesrnnssrnssrrnssrns Typical Connections to a Presidium Mim Connection to the VM15 Video Module sss eene nnns PIR Connections VM15 sbown sss eene nnne nennen nentes nnn Alarm and Isolate Input Confouraion eene eene nenne Alarm Outputs Select Function General Tab Areas Trigger Area Properties Alarm Logic Pinouts for Presidium General vO EE Pinouts for Presidium Mini UO connechor eene nens Access Secure Input Confouratton eene nnne nns Installation SCre rnis ca loi icone Te reete tal ed ede ep oe ti Presidium Setup Utility seen Presidium Licence Agreement Choose Setup Type eene Local Area Connection Properties assesses Internet Protocol Properties AA Establish Connection to the Presidium sss Establish Connection to the Presidium sssssss Entering IP Address and Port Number Port Redirection Example sese Enter Password inre ner deri aia etie eet ADPRO Presidium by Xtralis Change Video Standard Neal de ote A aati Presidium Setup eene Contrast Level Indicator M E Gamera Galibration lcm Lie e e eter eter rag Detection Parameters qme PA Et ele ETT D Customise Detection Sensitivity sess Alarm Behaviour EE Video Monttorimg nnn Network Tabiainiuudaies c Ee Ee
67. ed IP Address Note If uninstalling the Presidium Setup Utility and reinstalling to a different directory the Presidium Setup Plugin and the Presidium Upgrade Plugin must be uninstalled using Add Remove Programs before reinstalling the Setup Utility To install the Presidium Setup Utility 1 Insert the ADPRO Product DVD into the PC to autorun and show the following screen Vi is Chi ADPRO Product Presidium Installation Transmitters one and ds Upgrade Figure 31 Installation Screen Doc 12384 05 43 Installation and User Manual 44 Select the Presidium button The following screen will be displayed i Presidium Setup Utility Setup Welcome to the Presidium Setup Utility Setup Wizard The Setup Wizard will install Presidium Setup Utility on your computer Click Next to continue or Cancel to exit the Setup Wizard Figure 32 Presidium Setup Utility Select Next The Licence Agreement is displayed i Presidium Setup Utility Setup End User Licence Agreement Please read the following licence agreement carefully Licence Agreement 1 Grant of licence Subject to this agreement Xtralis grants the Licensee a non transferable non exclusive licence to use the Software and Documentation for its internal business purposes in accordance with the terms of this agreement 2 Restrictions on use The Licensee must fal opt use the Software in canfarmity with Cancel Figure 33 Presidi
68. el 46 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 4 4 Configure Presidium Once the Presidium Setup Utility has been installed and the PC s network connection has been configured use the following procedure to configure the Presidium 4 4 1 Connect to an Presidium 4 4 1 1 Local Connection 1 Ensure the fan cover is fitted to the front of the Presidium standard Presidium only Use the supplied crossover Category 5 Ethernet cable to connect the PC s network port to the Setup port on the front panel of the Presidium Ethernet port on Presidium Mini 3 Power on the Presidium 4 Double click on the Presidium Setup Utility icon on the PC desktop The following screen is displayed D Presidium Setup Utility Establish Connection To establish connection follow these simple steps 1 Configure your computer with an IP address of 192 168 1 2 and a subnet mask of 255 255 255 0 in the Network Connections control panel 2 Using the supplied network cable connect your PC to the Setup Port of the Presidium 3 Wait up to 60 seconds for a device to appear in the list below 4 Select a device from the ist and press Connect S Select from Ust of Local Units Ato Detected ES F o To connect to a device on a remote network enter the network address and port of the remote device below O Enter Network address IP Address or Host Name P Address Poet Connect ADPRO Presidium Corr
69. ent channel with black level at the base and peak white at the top The black portion at the base shows the unused levels at the lower range of the video signal If there is no black at the base of the indicator then the black level of the video is correct This can be changed by adjusting the camera s brightness level The green portion shows the active video range and should ideally extend from the base of the indicator to near the top of the indicator in order to maximise detection capability The white portion at the top shows the unused levels at the upper range of the video signal This can be changed by adjusting the camera s contrast level after the black level has been set general use of the Presidium It should only be used as a diagnostics A Important Itis not recommended to enable the Display All Tracks function during tool when setting up the Presidium 1 Once all settings are selected select Next The following screen is displayed Figure 47 Camera Calibration Doc 12384 05 55 Installation and User Manual ADPRO Presidium by Xtralis Camera Calibration Camera calibration calibrates the dimensions and depth of field of the camera s field of view Camera calibration is important to ensure that Presidium can accurately determine target sizes The detection areas and detection parameters are defined in the following sections To calibrate the camera 1 Position a person or object in the foreground of the dete
70. ent material such as pest control strips or surface spray will reduce any nuisance alarms caused by such events 2 8 4 Routine Detection Tests Regular site detection tests should be performed at least once per month but preferably weekly to check the Presidium system detects unauthorised intrusions The detection tests used as part of the maintenance program should follow the tests performed as part of the initial installation and commissioning The descriptions of these tests should have been documented in tables For each detection area the following should be performed Check that the detection area covered by each camera connected to Presidium matches the initial design and commissioning and that the detection areas programmed for Presidium are still aligned within the field of view of the camera Check that any PIR detector is still aligned as initially designed and commissioned Execute a test in each detection area based on the type of intrusion such as a walking target for opportunistic intruder Ensure that the alarm activation is reported as expected at the Presidium system and also that any third party system triggered from the Presidium system receives an alarm notification Repeat the tests under the different lighting conditions e g day or night Conducting tests at dawn dusk should also be considered as the lighting conditions at these times can provide the most challenging environment for detection It is also im
71. er of copies H ppl pl s Figure 64 Print Settings Printing the site configuration produces a print out of all channel settings as displayed in the Status tab refer to Status Tab on page 69 Doc 12384 05 71 Installation and User Manual ADPRO Presidium by Xtralis 72 4 5 4 Upgrading Presidium Software Ensure the Presidium Setup Utility is first upgraded to the latest version refer to the Xtralis web site The latest version of the Setup Utility is available on the website www xtralis com adpro Important Do not upgrade the Presidium software to Version 2 or greater with a Setup Utility V1 xx as this process may leave the unit in a state whereby the default setting may need to be reloaded Use the ADPRO Presidium Setup Utility to select and connect to the Presidium site to be upgraded Select Function Pree Ge he Rectan ros at to partan saa DT Figure 65 Software Upgrade option Check the Software Upgrade option Browse to the location of the upgrade file and select the file to be used for example Presidium upgrade 02 00 02 0001 adu Click the Upgrade button to start the process The following warning message is displayed S Software Upgrade You are about to upgrade the Presidium Software The upgrade file will be transferred to the Presidium your connection will be closed and the Presidium wall reboot after a few seconds Proceed with upgrade e Click OK to contin
72. esidium Doc 12384_05 13 Installation and User Manual ADPRO Presidium by Xtralis 14 6 Camera Positioning and Mounting The position and mounting of cameras is vital to ensure reliable performance from a Presidium System The essentials when choosing a position and mount for cameras are Ensure the camera mount and pole are stable even in windy conditions As the lens size increases smaller movements appear magnified and the stability of the camera mounting becomes increasingly important Ensure that there are at least three mounting points on the selected camera housing mounting A camera mounting used for a standard CCTV site implementation may not be suitable as some camera movement generally does not cause distress to an operator however Presidium relies on steady camera images Though the algorithms within Presidium allow for some camera shake it is advisable to use a heavy duty mounting location or pole The following figure shows a typically recommended mounting pole for a camera PIR combination as well as infra red illuminator IR illuminator optional mounted 0 15m 6 diameter schedule y 8m 6 below camera 80 Galvanized post y 4 5m 15 above ground 4 2m EE d Kess TS DA gt Q2 d d d d d dh e etat ee SRS SSRIS d d Ge o SCENE 052525252505 25 260605 S52 954495459949 4 4 4 d d 9050505060605 de gt e 2 te Ge e d Ge d dei d Q2 D d
73. esidium by Xtralis Installation and User Manual Appendix G Site Detection Tests Company Date Location Tested by 1 Detection Test Description Test Conditions day night dusk Test Description dawn Detection Area Test Camera Name and No Number 2 Detection Test Performance Detection Area Test Detection Pass Fail Camera Name and Test Due Test Performed Signed No Number Doc 12384_05 103 Installation and User Manual ADPRO Presidium by Xtralis 104 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Appendix H Site Maintenance Tables Company Date Location Maintenance by Table 11 Camera Maintenance Table Camera Name and Number Maintenance Due Maintenance Performed Signed Cleaned Window Housing Condition Cable Condition Heater or Blower functioning Correct Alignment Company Date Location Maintenance by Table 12 PIR Maintenance Table PIR Location Maintenance Due Maintenance Performed Signed Cleaned Window Window Condition Cable Condition Correct Alignment Doc 12384 05 105 Installation and User Manual ADPRO Presidium by Xtralis 106 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Appendix I Installation Quick Referenc
74. etres feet metres feet metres feet metres feet 4 8 30 98 6 19 20 65 3 10 14 48 2 5 6 0 37 123 8 25 25 81 4 15 18 60 3 9 8 0 50 164 10 35 33 109 7 22 25 81 4 15 12 0 75 247 16 53 50 164 10 35 37 123 8 25 16 0 100 330 22 71 67 220 14 47 50 164 10 35 25 0 156 515 34 112 104 343 23 74 78 257 17 55 Table 8 Horizontal FOV 22 Metres 75 Feet 1 4 camera format 1 3 camera format 1 2 camera format Max Distance Dead zone Max distance Dead zone Max distance Dead zone metres feet metres feet metres feet metres feet metres feet metres feet 4 8 33 108 6 20 22 71 3 11 16 53 2 6 6 0 41 135 8 26 27 90 5 15 20 67 3 10 8 0 55 181 11 35 36 120 7 22 27 90 5 15 12 0 82 272 16 54 55 181 11 35 41 135 8 26 16 0 110 363 22 73 73 242 15 48 55 181 11 35 25 0 172 567 35 115 115 378 23 76 86 283 17 57 Table 9 Horizontal FOV 25 Metres 83 Feet 1 4 camera format 1 3 camera format 1 2 camera format Max Distance Dead zone Max distance Dead zone Max distance Dead zone metres feet metres feet metres feet metres feet metres feet metres feet 4 8 37 123 6 20 25 81 3 11 18 60 2 6 6 0 47 154 8 26 31 102 5 16 23 76 3 10 8 0 62 206 11 36 41 137 7 23 31 102 5 16 12 0 94 309 17 56 62 206 11 36 47 154 8 26 16 0 125 412 23 75 83 275 15 49 62 206 11 36 25 0 195 644 36 117 130 429 24 78 98 322 18 58
75. ety of Information Technology Equipment Supplementary Information The products listed comply with the requirements of the Low Voltage Directive 2006 95 EC where applicable and the EMC Directive 2004 108 EC and carries the CE marking accordingly The products were tested in a typical configuration The CE Mark first applied in 2002 N237 Doc 12384_05 ADPRO Presidium by Xtralis Contents Tute e TEE 1 1 Features of the Presidium cence ee eee ee en KREE NEEN nunnu nnne nnn rennen rin nn rrr inne nra 1 2 Unique Features of Presidium Mini cernere nnne 1 3 Installation Steps nics 2 De Si GT Guide ee EENS A SEENEN RER e Te e TEEN a E Medie 2 1 2 860D6 EE 2 1 3 Intended Audience sessi en ensecaeaesa es eeeseauaesceeeeeseaeesseeeeaaneaeeeees 2 1 4 Other Ee De pEiecnI see ICE 2 3 The Role of Security 2 3 1 ADPRO Solutions AC Oe Lu UI fonde Tiene I a ch cated ues cater dts ed e 2 3 2 Presidium an ADPRO Solution p Tcu 2 4 Presidium System Concept eegene eech uo ep rh gr nr ep nar 2 4 1 Operational Concept ssssssssssssssssss eee ener nennen nenne nri en tena Ee Parameters EE 2 5 System Design 2 5 1 Preliminary Information E E EE Discuss Requirements otio ie eiae eto eese et ico peut aco c papae toot stor cp ipei Hecomiiendatlons 2 i tii
76. f standard procedures that should be followed while installing any electrical equipment including a rack mounted Presidium Ensure all local safety regulations regarding installation of electrical equipment are followed All cables should be routed neatly and held in place using routing trays channels or ties All cables should be labelled for future reference and the identifiers marked on cabling diagrams or plans Adequate space should be allocated between all equipment in the rack to provide ventilation Once all equipment has been installed and operating in the rack the temperature in the rack should be monitored to check that the equipment is operating within specified limits operating range 0 C 40 C Even though equipment may be operating within specified limits reducing the temperature will increase the operable life of all equipment in the system Note Do not stack Presidium Mini units on each other due to heat transfer between enclosures 24 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 7 Site Commissioning The Commissioning Phase consists of the following steps Presidium Configuration Detection Tests Soak Tests Monitoring Tests Appendix F contains a commissioning checklist for each Presidium channel 2 7 1 Presidium Configuration The first element of Site Commissioning is to configure the Presidium system Refer to Installation Configuration on page 43 for ins
77. f three elements Preliminary Information Gather general site information and discuss the security requirements with the customer to ensure that the Presidium meets the customer s requirements Site Survey Conduct a site survey to determine site requirements such as the positioning of cameras and other detectors lighting and existing and required communications infrastructure Equipment Selection Conduct a comprehensive analysis to determine equipment requirements such as camera types and lenses level and type of illumination and communications and control room equipment 6 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual The system design is critical to ensure that the Presidium system performs as expected A well designed system can deliver exceptional performance whereas a system that has not had a rigorous design process will not perform to expectations Presidium provides a high level of flexibility in its configuration but is dependent on the quality of video signals and scene content to deliver a high performance solution 2 5 1 Preliminary Information Gather site information to determine Presidium s suitability for the site If possible obtain a copy of the site plans to check the layout and suitability of Presidium Assess Site Plans Assessing the site plans prior to visiting the site allows a quick overview as knowledge of this is important for a good Presidium system design If unable t
78. for the defined time due to camera disconnection or output failure Note A no video alarm will not be generated if the channel is isolated 1 Once all Video Monitoring settings are complete select Finish The Presidium Setup screen is displayed refer to Figure 44 2 Repeat the channel configuration for all channels Once all channels are configured the following optional settings may be adjusted Doc 12384_05 65 Installation and User Manual ADPRO Presidium by Xtralis 4 4 6 Network Tab The Network screen enables a device name to be entered and the Presidium IP address to be changed if required Presidium Setup Utility APRO Presidium Setup Chances Network gh Level biss Securty Status Network Settings Device Name clum TP Adress Settings Uerder Yes IP Address Automabicaty Assigned Sabet Ma AuRomaticaly Acad Defaut Gateway Automatically Assigned The ADPRO Presidium device has three external network ports treo located on the back panal and ore on the front panel Internally these ports ore all connected together much Ke an Ethernet ach By dela the ADPRO Presidium has a dain IP address of 192 183 1 3 If you wont the ADPRO Predam to communicate rath external networks you must sat the defaut gateway Akermately f you want to configure the 40920 Presidium as a DHCP dert you may do so here requres a DHCP server to be avalatin H the ADPRO Presidium amp a DHOP chent ad there s no DHOP server
79. ge 19 Camera Installation on page 22 and Camera Lens Selection on page 99 PIRs Design and installation of PIRs with Other Detectors Selection and Location on page 15 Presidium PIR Alignment on page 17 Camera PIR Alignment on page 19 and PIR Installation on page 23 Presidium Configuration Configuring the Presidium system for operation Presidium Configuration on page 25 Commissioning and System Test Testing the system and checking the detection performance Performance Assessment on page 25 System Tests on page 26 and Site Detection Tests on page 103 System Maintenance Ensuring the system continually operates to the required criteria Site Maintenance on page 26 Site Detection Tests on page 103 and Site Maintenance Tables on page 105 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 3 The Role of Security Security is becoming an increasingly accepted part of every day living It is imperative for organisations to consider physical and information security as a fundamentally important element of their overall management strategy Suitable security must include detailed Risk Analysis and Management as well as an awareness of Business Continuity Management ensuring that the System instituted provides the organisation with the best approach to achieve ongoing success The key elements to instituting a security solution are Identify and Evaluate Risks Develop Stra
80. ge ENEE ton Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Figure 56 IP Address Configuration essere nennen nen trt te renes 66 Figure 57 Advanced Communication 67 Figure 58 High Level Interface rites npe e e be E E ER d EET LEE GC KEN HR 67 Nie UTC RE ele E EE 68 Figure 60 Status lab EE ENEE 69 Figure 61 Presidium Setup Screen sse rennen nen tenen nnne nes 70 Re ICH to RE 70 Figure 63 Load Settings from File 71 Figure 64 Print Settings tero cea v Pre terere en E ee eb e ERO Ee ER RU Reto e eR s 71 Figure 65 Software Upgrade option sss entente nnne nennen tenen rennes 72 Figure 66 Enter Password Window sess enne EEN EEN nennen nennen trennen 74 Figure 67 Reset Password eene ite aav e n ere BECA dace ern dee M RE E coude 74 Figure 68 Complete standard Presidium Installatton A DT Figure 69 Typical Connections to a standard Presidium s sss sess LO Figure 70 Installer Menu leon itte teet eee eL ene ra Rn EE dedu 79 Figure 71 Typical Video Transmitter User Settings sss sss 9 Figure 72 Presidium Inputs Lista i atre edo ee Ee Et e e ES 80 Figure 73 Unallocated lcon esee eene nennen nennt nnne entente innen nns 80 Figure 74 Presidium Input Settings esses nennen en rn tenentes 81 Figure 75 Mapping the camera inputs sssssssseses
81. gher bandwidth links im SHE Camera 1 Setup GUI used locally ADPRO Presidiu Te Ee oe Ch 22 mm Setup GUI used remotely can be on the same PC as Video Central Video looped through from Presidium FastTrace Network Communication ADPRO FastTrace H WAN Video Central used to monitor alarms generated by Presidium do oooop 0000000006 o eisai HLI sends all alams to FastTrace Figure 17 Typical Connections to a standard Presidium 2 6 System Installation Install the Presidium system and associated hardware in accordance with appropriate CCTV installation practices Ensure adherence to any local legal or mandatory requirements for electrical or telecommunications infrastructure Appendix contains a flowchart providing an overall view of the installation and commissioning process It can be used as a guide for the installation and commissioning sequence of events 2 6 1 Camera Installation Alignment Confirming the FOV of the camera is very important The initial design must ensure that the perimeter or area is completely protected and no dead zones are present Adherence to the design during installation ensures there will be no dead zones or blind spots in the protected area Placing traffic cones or markers at the edges of the expected detection areas foreground and background provides a mechanism to initially align the camera and ensure that the FOV is as per require
82. hat the dead zone of one camera is covered by another camera s field of view The area just in front of the dead zone can also be vulnerable to fast moving targets It is a good practice to ensure that the field of view of the camera covering the dead zone includes the dead zone plus an extra 1096 to 1596 of the area adjacent to the dead zone The following diagram shows the camera s FOV and dead zone in both perimeter and area protection scenarios Camera Dead Zone Camera Dead Zone Area to be Protected PIR Curtain Camera Field of View i H H H 1 1 1 I i Camera Field of View 1 i Fenceline Ot ee eee eee Termination Board Figure 5 Camera Dead Zone Coverage 5 Optimal Camera Angle Figure 4 which shows the dead zone of a single camera also shows the optimal camera angle The target closest to the camera should have its feet at the base of the camera FOV and the head of the target at the furthest detection distance should be just below the top of the FOV of the camera Normal video monitors do not show the full horizontal video available Presidium uses all of the horizontal video for detection Hence when aligning cameras it is important to take this into account and if normal monitors are to be used as opposed to underscanning monitors then care must be taken to mask out the extreme left and right hand edges of the image using the detection area selection capability of Pr
83. hms hence it is important that the FOV is not obtuse i e a target in the background on the left edge of the FOV must be the same size as a target on the right edge of the FOV When designing cameras to look along a fenceline the majority of the horizontal FOV of the camera should be on the monitored side of the fence 3 Camera and Lens Selection The maximum horizontal field of view and the likely target size to be detected determines the required camera and lens configuration The absolute maximum horizontal field of view where detection occurs should not be more than 30m 98ft Presidium functions most effectively when the camera is not mounted too high The perspective characteristics used in the detection algorithms will not function as expected when the camera is mounted too high When looking directly down on a cat or a person their relative sizes are quite similar the true sizes can be judged only when viewing at an angle Place the camera at a height that it is out of reach of intruders This should be between 3 6 metres 9 8 19 7ft The ideal height is 4 2m 14ft as this allows the detection algorithms to function and is high enough to prevent tampering with the camera Analysis of the site plans and information from the site survey determine the FOV of the camera to ensure coverage of all areas requiring protection Always ensure that the maximum horizontal FOV is no greater than 25m 82ft to avoid compromising detection
84. iated with the equipment When a no video or contrast alarm occurs the Presidium still sends video with an error message displayed This means that if the DVR has a no video or contrast monitoring function it will not detect these fault conditions The alarm output of the channel in alarm is activated and will remain active until the problem is rectified Channels may be isolated by wiring relay outputs from the DVR to the Alarm Isolate inputs on the Presidium refer to Alarm Inputs on page 35 The Presidium may be switched between access secure by wiring a relay output from the DVR to the Access Secure pin of the I O connector on the Presidium refer to Access Secure Input on page 38 The Presidium does not supply camera names or time date information with the video The DVR must be used to supply channel names and time date Tracking information can be supplied by the Presidium There a two types of tracking provided Display Alarm Tracks on Video Output A track is displayed showing the path taken by a target as it moves through the detection area The track is only displayed once an alarm has been generated Display All Tracks on Video Output This option should only be used for diagnostics Tracking may be disabled if required refer to General Setup on page 54 Doc 12384 05 85 Installation and User Manual 86 ADPRO Presidium by Xtralis Doc 12384_05 MINI ADPRO Presidium by Xtralis Installation and User Manu
85. in order to deter intruders is not effective because if illumination levels are too low Presidium may not detect the intrusion If the scene contrast is poor and no additional lighting can be installed then the contrast can be increased by adding stripes to walls and pathways by painting the background surfaces a light colour or by laying strips of different colours of gravel Determining the required lux level from a mathematical calculation can be difficult There are references available that describe this process in detail Refer to these references or other sources for a mathematical approach in determining the lux level required at a site to provide adequate illumination for the cameras selected Lux meters are available for checking the illumination level at a site and to relate the measurements to camera specifications A good rule of thumb is if the target is clearly visible to the human eye at the maximum range under the worst lighting conditions then a camera can detect it Doc 12384 05 19 Installation and User Manual ADPRO Presidium by Xtralis The following are some key considerations in determining the best illumination method The requirements will dictate if IR illuminators or visible lighting is used The cameras used with IR illuminators must be either B amp W or day night cameras capable of automatically switching between colour B amp W depending on the conditions Visible lighting must be used for colour cameras The leve
86. ion module two VMD channels per module One VM15 module per chassis is required for basic operation General Alarm Fault Relay Switching Voltage 30 VDC maximum Switching Current 1 Amp maximum Isolation 750 V maximum 90 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Appendix A False and Nuisance Alarms Ultimately no security system is perfect generally through generating false or nuisance alarms As a security system is made more sensitive to detecting intrusions the false and nuisance alarm rate can increase False or nuisance activations limit the effectiveness of a security system as operators become used to receiving alarms that are not valid and may miss valid alarms assuming that the alarm is just another false or nuisance alarm A False Alarm can be defined as an alarm activation that is reported but the cause of which can not be identified A Nuisance Alarm can be defined as an alarm activation that is reported but the cause of the alarm can be verified and no further response is required The goal in designing a security system is to provide the highest rate of successful detection traded off against the lowest rate of false and nuisance alarms Using a system such as Presidium coupled to FastTrace FastTx or FastTrace R provides the capability to remove Nuisance Alarms as a problem as the alarm must be verified remotely at a Monitoring Centre prior to dispatch of personne
87. ises such as erection of temporary or permanent structures facilities maintenance activities or new operating procedures Doc 12384 05 27 Installation and User Manual ADPRO Presidium by Xtralis 28 2 8 3 Routine Equipment Maintenance There are a number of regular maintenance tasks that should be performed monthly to ensure that the Presidium system continues to perform as expected General inspection of all cabling conduit connectors glands and housings to ensure that they are all in good working order and not suffering deterioration General inspection of the standard Presidium chassis ensuring that it is dust free and the fan mounted on the power supply is not obstructed in any way Remove the fan cover from the front panel it clips off and check whether the fan filter requires cleaning or replacement Regular cleaning of camera housing windows with lens cleaner and a lint free cloth to ensure that the performance of the system is not prejudiced by poor image quality Check that any heaters blowers washers or wipers installed on camera housings are operating as expected Regular cleaning of the window on any PRO series PIR The window should be cleaned with lens cleaner and a lint free cloth If the window is showing signs of deterioration or peeling please contact your Xtralis supplier for replacement details Where insects or spiders can be a problem in or near camera housings the provision of insect repell
88. l The use of a second detection technology device e g PIR microwave detector or fence sensor may also be useful in minimising false alarms The second device may be ANDed with VMD to provide double knock alarm generation In addition a well designed and correctly installed system can limit the generation of False Alarms significantly The capability of reducing the impact of both of these types of problem alarms greatly enhances the utility and suitability of the Presidium Intelligent Video System to a number of scenarios Doc 12384 05 91 Installation and User Manual 92 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Appendix B Site Survey Checklist Company Date Location Survey by Site Plan Annotation Checked Location of lighting Location of equipment room Communications infrastructure identified Trees identified and marked Location of fences and barriers Location of nearby roads Location of adjacent structures Location of existing CCTV systems or other detectors Location of all structures Other Requirements Site images acquired Clarification of customer and security expectation Clarification of any special security requirements Doc 12384_05 93 Installation and User Manual 94 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and U
89. l of lighting required is higher for colour cameras as these have less sensitivity compared to B amp W cameras The sensitivity of the cameras determines the required level of illumination When visible illumination is used the lighting should be sufficient for the human eye to see targets at the maximum detection range When using IR illumination verify the intensity by viewing the camera output on a monitor It is important to ensure that areas where lighting casts shadows do not provide dark areas for intruders to utilise Illuminators visible or IR should not be positioned to face directly into a camera Typically the best type of visible lighting is closest to normal daylight i e a white light source rather than a coloured light source such as sodium vapour Figure 16 Correctly Illuminated Scenes Equipment Room The equipment room for mounting the Presidium equipment should meet the following requirements 20 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Environmental Requirements The equipment room should meet the following environmental specification Temperature 0 C 32 F to 40 C 104 F standard Presidium Temperature 0 C 32 F to 40 C 104 F Presidium Mini Humidity less than 9096 non condensing Power Supply Depending upon security requirements a backup power supply such as a UPS should be considered To ensure total system reliability in the event of power
90. lay Units 1 Once the Detection Parameters have been defined select Next The following screen is displayed Figure 53 Alarm Behaviour Alarm Behaviour The Alarm Behaviour screen enables the configuration of the alarm input VMD behaviour and channel isolation Alarm Input 1 Check the Enable checkbox if a second detection technology device e g PIR microwave detector or fence sensor is connected to this channel 2 Enter a descriptive name for the alarm input in the Alarm Input Name box This name is displayed on the Setup screen but is not communicated to a FastTrace FastTx FastTrace R or VideoCentral if connected 3 Select the type of the Alarm Input Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resistor Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL 4 Select the required Hold Time for the alarm input The Hold Time determines the length of time that a triggered alarm input is active when being ANDed with VMD to generate an alarm double knock method The Hold Time commences when the alarm input has stopped triggering A VMD alarm must be triggered within the Hold Time for an alarm to be generated Any tamper condition on the alarm input will generate an alarm and activate the general alarm relay Note An alarm input or input tamper alarm will not be generated if the channel is isolated
91. lis Installation and User Manual Camera PIR Alignment The camera alignment relative to the boundary and other cameras is paramountin ensuring that there are no blind spots on the site Align each camera to cover the dead zone of the next camera and to adequately cover the area under protection If due to practical limitations external areas not requiring detection are included in the camera view use the detection area selection feature in Presidium configuration to mask out such areas The following figure shows camera alignment and PIR alignment around the perimeter of a facility Camera Dead Zone PIR Curtain I I I U I U I I 1 LI Camera Field of View LI 1 k Fenceline pi y Te die ee ede e 1 1 ke em zm zm em em mm M i P Termination Board Figure 15 Camera PIR Alignment Illumination Requirements Ideally the illumination around the site should be even with no major contrast changes caused by shadows at all times of the day and night Typically to provide more even illumination it is better to utilise high levels of ambient lighting throughout the field of view of the camera rather than subjective lighting systems To ensure continuous monitoring by Presidium the lighting or illuminators should be on at all times during hours of darkness typically photo cell controlled Switching illuminators on at the point of alarm
92. lity The Presidium should now appear in the list of local units Reboot the PC or reinstall the Presidium Setup Utility if the Presidium does not appear 4 6 4 Password Forgotten If the Presidium password has been forgotten 1 Connect the Presidium to a PC with the Presidium Setup Utility installed 2 Open the Presidium Setup Utility 3 Highlight the required Presidium in the list and press Connect The Enter Password window is displayed Enter Password DER Enter Password for Device ADPRO Presidium Remember password Forgotten Password Figure 66 Enter Password Window 4 Select Forgotten Password The Reset Presidium Password window is displayed V Reset Presidium Password If you Forgot your password you can reset it to the system default Enter the ADPRO Presidium Setup Disk into your CD DVD ROM drive Choose the drive letter from the list below Press Reset P W to reset the password Drive Letter Figure 67 Reset Password 5 Insert the ADPRO Installation and Upgrade DVD into the PC 6 Select the drive letter from the drop down list 7 Select Reset PW 8 Select OK at the confirmation screen The password is reset to admin Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual Note Presidium Mini uses an internal hardware jumper to reset the unit to its factory default password Contact your local Xtralis representative for details 4 6 5 HLI Connection to Fast
93. ll send an alarm When connected to a FastTrace FastTx FastTrace R or third party DVR the Access Secure input must be set to Secure The state is then controlled by the connected DVR The Access Secure Input state may be Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resistor Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL Doc 12384 05 ADPRO Presidium by Xtralis Ground Connection Access Secure Input Ground Connection Access Secure Input Ground Connection e R1K1 Access Secure Input Ground Connection e e RIKI Access Secure Input Ground Connection R1K1 R2K2 Access Secure Input e le Ground Connection hd RIKI R2K2 Access Secure Input p e Installation and User Manual Normally Open NEOL Short Circuit Alarm Open Circuit Sealed o Tamper Operation ormally Closed NEOL hort Circuit Sealed en Circuit Alarm o Tamper Operation zouoz ormally Open SEOL ort Circuit Alarm ow Impedance Sealed en Circuit Tamper or moz ormally Closed SEOL hort Circuit Tamper ow Impedance Sealed pen Circuit Alarm or oz Normally Open DEOL Short Circuit Tamper Low Impedance Alarm Hi Impedance Sealed Open Circuit Tamper
94. lly linked with any other detectors in use and the availability of suitable lighting 1 Camera and Video Signal Requirements Cameras must adhere to the CCIR PAL or RS170 NTSC standard for suitable operation with Presidium Each camera channel can pass both colour and monochrome video signals Presidium only processes the monochrome section of the video signal Any colour signal present neither adds nor detracts from the performance The following conditions must be met for the Presidium to synchronise to an incoming video signal from the camera and to provide good video motion detection The sync amplitude at the video input of the Presidium must be within 0 2V to 0 4V range The video amplitude not including sync at the video input of the Presidium must be within the range of 0 5V to 1 0V White 1 Volts Video content 0 7 Volts 0 5 to 1 0 Black 0 3 Volts D Volts Sync pulse 0 3 V Chroma Burst 100mV 0 2 to 0 4 Ground reference Figure 3 Required Video Signal If the video level at the video input of the Presidium is low cable compensators or line drivers should be installed at the camera end and adjusted to boost the video signal to within the correct voltage levels Typically the best solution is to ensure that the correct grade of coaxial cable is installed to transmit the images over the required distance Take into consideration impedance and capacitance qualities of the selected cable type to ensure that image
95. ment Alternatively have one person watch a monitor and direct another use a walkie talkie to walk the site 22 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Installation Hints When installing cameras in camera housings the following hints will avert some nuisance alarms The application of insect repellent material such as pest control strips or surface spray reduces any nuisance alarms caused by insects or spiders in or near camera housings Place a bead of silicone across the top of the shield or housing near the front This prevents water droplets falling in front of the camera off the front of the sun or rain shield of the housing When water hits the bead it diverts to the side and does not collect along the front of the housing Rain or sun shields can catch the wind causing significant camera shake To restrict camera movement appropriately increase the strength of the fixing hardware as the size of the shield increases Interference Caused by High Voltage or Ground Loops There is significant potential for interference to video signals in some installations particularly on sites with high voltage infrastructure such as electricity substations High ground loop currents are produced between equipment earthed at different points around the site Depending upon the level and type of interference the ground loop currents have the potential of causing nuisance alarms or a reduced detection rate
96. nergy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures re orientate or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment to a power outlet which is on a different power circuit to the receiver or consult the dealer or an experienced radio television technician for help Document Conventions The following typographic conventions are used in this document Convention Description Bold Used to denote emphasis Used for names of menus menu options toolbar buttons Italics Used to denote references to other parts of this document or other documents Used for the result of an action Doc 12384_05 i Installation and User Manual ADPRO Presidium by Xtralis MINI The following icons are used in this document Convention Description Caution This icon is used to indicate that there is a danger to equipment The danger could be loss of data physical damage or permanent corruption of configuration details Warning This icon is used to indicate that there is a danger of electric shock This may lead to death
97. ning a Presidium Fault finding an installation Configuring detectors Disabling faulty detectors Both the alarm input and alarm isolate connections are tamper protected regardless of the access secure state To ensure the best immunity to EMC disturbances the isolation input should be wired using shielded cable Connect the shield to the ground GND terminal Note If a channel is isolated no alarm input or tamper alarm will be generated The Isolate input state may be Normally Open No End Of Line NEOL Resistor Normally Closed Normally Open SEOL Single End Of Line Resistor Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 3 8 Alarm Outputs There are alarm outputs provided for each video channel on a VM15 module or Presidium Mini and labelled ALM A O P and ALM B O P Alarm outputs may be used to connect the Presidium to third party alarm panels DVRs etc The alarm outputs are normally open When in an alarm state the alarm outputs are closed ALARMA O P ALARMB O P ALARM O P COM Figure 27 Alarm Outputs Alarm output relay activates on the occurrence of an intrusion alarm or tamper condition All outputs on the alarm connector share a common ground 3 9 General I O Connector To ensure the best immunity to EMC disturbances the connections on the general I O connector should be
98. nly want this channel to use the new thresholds you should create a new sensitivity Detection Sensitivities Video Motion Thresholds Low New Sensitivity Minimum Area sq m Medium Hon Remove Sensitivity Maximum Area sq m Custom Detection Sensitivity Minimum Width m Maximum Width m Minimum Height m Maximum Height m Minimum Speed mys Maximum Speed m s Minimum Distance m Minimum Density Scene Change Threshold Scene Change Holdoff s Detect Delay s Cas Figure 52 Customise Detection Sensitivity This window may be used to create a customised sensitivity level or to edit an existing custom level Note The standard Low Medium and High sensitivity levels may not be modified or deleted Doc 12384_05 61 Installation and User Manual ADPRO Presidium by Xtralis To create a customised sensitivity level 1 Highlight the sensitivity level on which the new level is to be based 2 Select New Sensitivity 3 Enter a name for the new sensitivity level and select OK 4 Modify the Video Motion Thresholds on the right side of the window as required values outside of the valid ranges may not be entered 5 Select OK The window closes and the new level is selected for this channel To remove a previously created customised sensitivity 1 Highlight the custom level to be removed 2 Click the Remove Sensitivity button 3 Click Yes To modify a custom level
99. nm Channel Status hereal free Doc 12384_05 53 Installation and User Manual ADPRO Presidium by Xtralis 4 4 5 Configure Channels Configuring the channels enables cameras detection areas and alarm behaviour to be defined General Setup 1 Highlight the required channel and select Configure The following screen is displayed Figure 45 General Tab Channel Name Enter a name for this channel The name is only displayed on the Setup screen but not on the video output Terminate Video Input Select this check box to terminate the camera in 75 ohms unless the video input is teed off to another device The video input should normally be terminated Display Alarm Tracks on Video Output When this checkbox is selected a track is displayed on the video output showing the path taken by a target as it moves through the detection area The track is only displayed once an alarm has been generated Alarm tracks are displayed as red Display All Tracks on Video Output When this checkbox is selected a track is displayed on the video output showing all registered objects that are moving in the detection area These tracks are displayed as green A contrast level indicator is also displayed on the video output 54 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual CONTRAST LEVEL Figure 46 Contrast Level Indicator The contrast level indicator shows the dynamic range of the video on the curr
100. no video external alarm input tamper The GAR contacts will remain in the changeover condition until all alarms are reset with the following conditions When an alarm output is set to pulse the GAR will remain active for the duration of the longest pulse time of any alarm input source that has been activated When an alarm output is set to while active the GAR will remain active while any alarm input source is active When a combination of pulse and while active is used by various inputs the GAR will remain active for the longest pulse time of teh various sources that have become active or while any source not set to a pulse time is active When set to pulse the GAR will not re activate until the longest alarm hold off period for any channel that has gone into alarm has expired Refer to Specifications on page 89 for the relay specifications 3 10 Network Communications 3 10 1 Presidium Two 10 100 1000Base T network ports LAN1 and LAN2 are provided on the back panel One 10 100Base T network port labelled SETUP is provided on front panel This port is primarily used to setup and program the Presidium 3 10 2 Presidium Mini One 10 100Base T network port ETHERNET is provided 3 10 3 Network Connector LEDs Integrated LED diodes in the network connectors are used to indicate LINK UP LINK SPEED and LINK Activity as defined in the following table Doc 12384 05 ADPRO Presidium
101. o obtain site plans prior to visiting the site then once on site prepare a sketch of the site remembering to include the immediate external environment such as roads and location of neighbouring buildings Discuss Requirements During the preliminary stages discuss the security requirements and expectations with the customer s representative Different areas of the site may have varying security requirements and knowledge of the external environment is critical in understanding the customer s requirements and performance expectations from the system Collect information about the customer s response requirements such as use of local guards and or remote monitoring Recommendations If after the preliminary investigation phase the site is deemed suitable for Presidium and the customer s performance expectations can be met a site survey should be conducted The following criteria determine the site s suitability for a Presidium System 1 Sterility of protected area i e how well defined is the border surrounding the protected area is the area free from general or expected activity and are there clear areas in which detection can occur 2 Customer requirements for response onsite or remote 3 Customer expectations of system performance such as false alarms or integration into third party systems 4 Possible addition of other detection technology e g PIR 5 Atthe maximum distance from the camera where a target is expected to b
102. on 2 The location for the installation of the Presidium system to confirm cable run lengths for cameras 3 If remote monitoring is to be used confirm the location and type of any existing communications infrastructure 4 Location of trees and other vegetation that may affect detection performance camera positioning and field of view 5 Type and height of fences or barriers to check where intrusion is likely to occur Also determine if any concealment of intruders may occur and what is visible through fences 6 Anyother permanent or semi permanent structures not already marked on the site plan e g semi permanent location of large cable drums which may obscure camera views 7 Location of any nearby roads to determine whether street lighting or car lights from any roads nearby may present a lighting problem 8 Location and description of nearby buildings or structures to understand whether lighting may spill from adjacent properties or shadows from industrial equipment may affect performance e g a shadow from a moving crane cast across the FOV of a camera may cause nuisance alarms 9 Location of any existing CCTV cameras or other detectors and their suitability with the Presidium system or incorporation as a third party detector 10 Special requirements within protected areas i e high security critical areas within the site or special requirements due to dangerous chemicals and or service reliability 11 If audio is consi
103. on Properties General Authentication Advanced Connect using HB 3Com 3C920 Integrated Fast Etheme This connection uses the following items Client for Microsoft Networks E B File and Printer Sharing for Microsoft Networks M E QoS Packet Scheduler M 3 Internet Protocol TCP IP Install Uninstall Description Allows your computer to access resources on a Microsoft network v Show icon in notification area when connected v Notify me when this connection has limited or no connectivity Figure 35 Local Area Connection Properties 4 Highlight Internet Protocol TCP IP and select Properties The following screen is displayed Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 158 1 2 Subnet mask 20 Zon Zoot 0 Default gateway Use the following DNS server addresses Preferred DNS server ES Alternate DNS server Figure 36 Internet Protocol Properties 5 Change the PC IP settings to the following 192 168 1 2 6 Set the subnet mask address to 255 255 255 0 7 Click OK and the Local Area Connection Properties box is displayed again Click OK and close the Network and Dial up Connections pan
104. on a desk top do not stack on each other due to heat transfer between enclosures Referring to Figure 20 Presidium Mini has two video movement detection channels Video A and Video B Each channel incorporates Alarm Input Connectors one per channel to enable alarm sensors e g Passive Infra Red PIR microwave etc to be associated with cameras GND Ground A S Access Secure Mode FLT N C Fault Normally Closed r FLT COM Fault Common VIDEO IN VIDEO OUT r FLT N O Fault Normally Open _ gt _ gt A B A B 2 ETHERNET INDO ALM B IP Alarm B Input ALM B ISOLATE Alarm B Isolate ALM B OPP Alarm B Output ALM OP COM Alarm B Output GND Ground ALM A IP Alarm A Input ALM A ISOLATE Alam A Isolate ALM A OP Alarm A Output Figure 21 Rear View of the Presidium Mini enclosure 30 Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual E Setup GUI used locally A Setup GUI used remotely can be on the same PC as Video Central WS ES Video Central used to monitor alarms generated by Presidium HU sends all alams to FastTrace Figure 22 Typical Connections to a standard Presidium ACCESS SECURE switch Saas Setup GUI used remotely can be on the same PC as Video Central Local Video Monitors Figure 23 Typical Connections to a Presidium Mini Doc 12384_05 31 Installation
105. on the HLI tab refer to High Level Interface Tab on page 67 should be set to 192 168 5 10 The Status Tab on the Presidium setup will indicate whether the Presidium has connected to the FastTrace FastTx FastTrace R in the High Level Interface section Connected to FastTrace DVR yes no The following IP Addresses must be changed in the following order Presidium IP Address Refer to Network Tab on page 66 for instructions to change the Presidium IP Address FastTrace FastTx FastTrace R IP Address Refer to the FastTrace FastTx FastTrace R User Manual Communications section for instructions to change the transmitter s IP Address The Site IP Address used by VideoCentral to communicate with the transmitter Refer to the FastTrace FastTx FastTrace R User Manual Setting the Network Connection section for instructions PC IP Address if further configuration is required Refer to Configure the PC Network Connections on page 45 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 6 Connection to a Third Party DVR Setup GUI used locally Video looped through from Presidium Presidium alarm outputs connected to DVR alarm inputs Monitor Keyboard bac Figure 78 Typical Connections to a Third Party DVR The above diagram shows a sample configuration for connecting a Presidium to a third party DVR The following section describes settings and behaviour assoc
106. ons using a different technology can reduce nuisance and false alarm rates to minimal levels dramatically increasing the overall effectiveness of the system The benefit of verifying the nature of the intrusion through video images is paramount with the additional technology providing an extra level of security The use of PIR detectors is a well established and field hardened method of providing security The ADPRO range of PIR detectors feature long range and wide angle detectors suitable for perimeter protection and for area protection respectively The operable range of the detectors varies from 18m 60ft for the wide angle up to 150m 500ft for the longest range PIR Prevailing site conditions determine the effective range The recommended maximum is 100m 330ft Doc 12384 05 15 Installation and User Manual ADPRO Presidium by Xtralis The following diagrams illustrate the alignment of a long range PIR with the camera field of view and a wide angle PIR with the camera FOV Camera Field of View PRO Detector PIR Field Direction of of View Intrusion Figure 8 FOV of Curtain PIR with Camera Camera Field of View PIR Field of View Figure 9 FOV of Wide angle PIR with Camera To aid aligning the camera and the PIR it is recommended that the PIR is mounted as close to the camera as possible preferably mounting off the same bracket as the camera as shown in the following diagram ADPRO PRO Detector I
107. or permanent injury Warning This icon is used to indicate that there is a danger of inhaling dangerous substances This may lead to death or permanent injury Information This icon is used to indicate that the particular feature or action is not available when using the Presidium Mini product MINI Apple m DNSResponder Licence Agreement Presidium uses Apple mDNSResponder open source software This software is covered by the Apple Public Source Licence PApple mDSNSResponder software is available from Apple website http developer apple com opensource internet bonjour html The ADPRO Product Installation and Upgrade DVD contains a copy of all distribution licences relevant to Presidium Tradename statement Xtralis ADPRO is a registered trademark of Xtralis AG Pty Ltd Lightning or Related Voltage Surges Damage or malfunction caused by lightning or related voltage surges may be excluded from the manufacturer s warranty at the manufacturer s discretion Safety Procedures Installations in the United States of America and Canada For systems installed in the United States of America and Canada the following requirement is applicable All equipment installations are required to be in accordance with the National Electrical Code NEC ANSI NFPA 70 and the Canadian Electrical Code CEC Part 1 CAN CSA C22 1 If the power cord is not supplied with the Presidium select the proper power cord according to your local
108. os A remotely monitored standard Presidium System linked to a FastTrace or FastTx provides rapid remote response with an option for local response follow up The response from a remote monitoring station followed by dispatch of security guards or law enforcement provides a powerful flexible and effective solution to many site security problems The presence of a Presidium System at a site can provide rapid local response When local notification via standard CCTV monitors is linked to alarm systems for visual and audible notification at a local monitoring station it is possible for guards to respond appropriately in the minimum timeframe Automatic monitoring of multiple video channels provides significant security and cost benefits Doc 12384 05 5 Installation and User Manual ADPRO Presidium by Xtralis 2 4 Presidium System Concept This section provides a brief description of how Presidium performs image processing to determine if an intruder is present in the protected area 2 4 1 Operational Concept Presidium analyses video from CCTV cameras to detect movement that is likely to be an intruder A number of criteria used in conjunction with complex image processing routines are used to distinguish between an intruder and some other form of movement The same techniques are used to reduce other factors such as changes in contrast from shadows cast by clouds and moving trees Presidium monitors contrast changes and rate of cont
109. ould be subjected to dawn dusk shadows some camera movement or occasional strong wind and rain cloud shadows or snow High Use this setting for scenes between Medium and Very High Very High Use this setting when the detection area is cluttered has a lot of shadow activity camera movement wind rain clouds or snow High environmental activity may cause false alarms to be generated To minimise this dual technology using another sensor in an AND double knock configuration that complements VMD should be used m Se To define your own the detection sensitivity parameters press the Customise Sensitivity button a d Cancel Back Next Figure 51 Detection Parameters Detection Parameters The Detection Parameters enables the detection sensitivity of the Presidium channels to be adjusted Detection Sensitivity This setting adjusts the sensitivity of the channel to movement within the detection area This setting defines the level of intrusion being guarded against There are three default levels of sensitivity low medium and high If detection problems are experienced with the default levels it is possible to customise a new sensitivity level however the default levels should normally be used Please refer to the on screen descriptions for guidance on the setting to use based on the camera view Environmental Activity This setting defines how busy the background scene of the detection area is generally likely to be Id
110. pe of intrusion and where possible differing environmental conditions e g day night dusk dawn Ensure that the alarm activation is reported as expected at the Presidium system and also that any third party system triggered from the Presidium system receives an alarm notification If the system is installed in a high security installation then tests with different types of camouflaged clothing should also be performed Soak Tests Once the system has been installed and the detection tests performed then the system must be monitored for its performance in relation to the ambient environment Changes in environmental conditions or just routine actions can produce nuisance alarms The system should be monitored on a daily basis prior to going live to highlight issues of concern and then adjust the Presidium parameters as required Every time detection parameters are modified detection tests should be performed again to ensure the detection performance has not been compromised Once the performance of the soak tests has reached an acceptable level and the detection performance is as required the system can go live 2 7 3 System Tests Typically Presidium is an element of a larger system The integration and performance of Presidium as a system component must be verified to ensure the complete system behaves as required and expected There are a number of areas to check For remote monitoring ensure that generated alarms are suc
111. portant to check that detection is not occurring in areas in which detection should not occur In each detection area check that detection does not occur in areas that should be masked out or should not be aligned with PRO series PIRs or other detection technology With the PIRs in particular check that detection does not occur past the defined maximum detection point 2 8 5 Maintenance to Regulatory Requirements Regular maintenance and testing of security systems may be mandated by internal organisational requirements but in some industries specifically high risk industries such as nuclear power generation there may be statutory requirements for maintenance and testing Please check with the appropriate government agencies to determine whether any such criteria apply in your industry area Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 3 Presidium Connectors 3 1 Presidium The standard Presidium is housed in a DIN4194 Eurocard standard 3U high subrack unit It is designed to be mounted horizontally in a standard 19 inch rack Referring to Figure 19 the Presidium may be configured with the following modules From one to ten VM15 Video Modules may be installed in Video Module slots 1 to 10 depending on the number of video movement detection channels required Each VM15 Video Module provides video movement detection for two channels cameras Extra VM15 Video Modules may be retro fitted to provide a ma
112. pplied Construction Standard 19 rackmount 3U high subrack to DIN4194 Presidium Mini Metal desktop enclosure Two mounting ears used for wall mounting Dimensions 482 mm 19 inch W x 132 mm 5 2 inch H x 281 mm 11 inch L Presidium Mini 263 mm 10 3 inch W x 73 mm 1 3 inch H x 236 mm 9 3 inch L Weight Rackmount Fully configured system 8 7 kgs 19 2 pounds Presidium Mini 2 0 kgs 4 4 pounds Temperature Range Operating range 0 40 C 32 104 F Humidity less than 90 non condensing Doc 12384 05 89 Installation and User Manual ADPRO Presidium by Xtralis EMC Compliance Emissions Class A compliance to EN55022 1998 A1 A2 AS NZS CISPR 22 2006 FCC Part 15 Harmonic Current Emissions to EN61000 3 2 2000 Voltage Fluctuations amp Flicker to EN61000 3 3 1995 A1 Immunity EN50130 4 1995 A1 A2 Alarm Systems Product Family Immunity Standard UPS required for compliance with 100 mS mains voltage interruption requirement applies to Presidium only Safety Compliance IEC 60950 1 2001 CB Report including national deviations for AU CA KR US and EU Group UL Listed to US and Canadian Safety Standards under File E219750 pending Warranty Twenty four 24 months on all components Configuration Options The standard Presidium chassis has slots for up to ten video input modules Each module has two channels of VMD Video Input Module option VM15 video intrusion detect
113. r Manual HE ss A Suitable Scenes Unsuitable Scenes Figure 1 Suitable Unsuitable Perimeter Conditions Doc 12384_05 9 Installation and User Manual ADPRO Presidium by Xtralis E E Suitable Scenes Unsuitable Scenes Figure 2 Suitable Unsuitable Area Detection Scenes Presidium is used in perimeter and area protection scenarios The key to providing a successful solution is installing Presidium into a scenario that is suited to its requirements Essentially the sterility of the area perimeter to be protected is paramount It is essential to have clear areas for target observation with minimum continuous or sporadic movement from non target sources Clarify Requirements The exact requirements for site security must also be clarified through tender documents or engineering specifications This is vital to ensure that the system design and installation meets the customer s expectations It is good practice to draft a commissioning schedule to further clarify the system acceptance criteria Details of system commissioning are described in Site Commissioning on page 25 10 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 5 3 System Hardware Appendix D contains a checklist for system design and equipment selection Camera Selection and Location The selection and location of cameras is vitally important for the successful operation of the Presidium Video Intrusion System The cameras are intrinsica
114. rast change within the defined detection areas This information on contrast changes and rates of change is fed into a number of computational routines that analyse the changes and extract valid targets from the images whilst rejecting changes from background movement The detected targets are further analysed to ensure that they meet criteria based on size and speed If the criteria is met an alarm is generated What is actually considered a target will depend on your particular security requirements In a high security environment the maximum horizontal Field of View FOV should be less than for that in a medium security environment 2 4 2 Basic Parameters To achieve high detection probability and effective nuisance alarm rejection the field of view at the maximum detection distance should be no more than 16 7 times the target size For example to detect a 1 8m high human target the recommended maximum field of view at the maximum detection distance is FOV 16 7 x 1 8m 30m If a larger field of view is used then the detection probability is reduced In this scenario increasing Presidium s sensitivity can only partially compensate for the reduced detection probability and may lead to an increase in the number of false alarms It is not recommended The maximum horizontal FOV and the required target size to be detected determines the required camera and lens configuration 2 5 System Design The system design phase consists o
115. re available for each type of ADPRO PIR provides a very accurate method of aligning the PRO detector The tester provides an output showing the IR activity that the PIR is sensing This requires two people where one acts as a target while the other adjusts the alignment of the PIR to cover the required detection area Doc 12384 05 23 Installation and User Manual ADPRO Presidium by Xtralis em eee eee e Camera Dead Zone PIR Curtain Camera Field of View f Fenceline l I ma Termination Board Figure 18 PIR Alignment on Fenceline It is important that the PIR curtain is aligned approx 0 5m 2ft inside the fence when a long range PIR is used next to a fence line the previous figure illustrates this The PIR can be aligned using previously described methods Confirm correct alignment with a walk test performed immediately adjacent to the fence ensuring that detection does not occur in the 0 5m 2ft area directly next to the fence It is important to ensure that the extents of the PIR detection are within the FOV of the camera i e if a wide angle type PIR is used the camera FOV must overlap the PIR detection area To confirm this the alarm output status or the test output using the PIR tester software of the PIR should be monitored as a person walk tests the site Ensure the person remains within the FOV of the relevant camera 2 6 3 Instrument Racks and Cablings There are a number o
116. rt 80 3 Once the router has been configured at both ends of the network enter the xDSL IP Address and the first Port Number for the Remote Public Network within the Presidium Setup Utility and select the Connect button Note The Presidium Mini IP Addresses can be change to suit the setup of the respective network The Presidium Mini Port Address cannot be changed fe Edt View Hoy Bookmarks Tod Hep 2s A O eme ie tu D gt Q Getting Started E Latest Headines Port Redirection Table lt Back Index Service Nome Protocol Public Port Private IP Private Port Active 1 Mini 81 TO 1 192 16013 Mini amp 192 168 14 CH en 0 0 0 0 0 Seed ep eon I Cox PUPAN 2009 DrayTek Carp Ali Migrtu Bereet Figure 40 Port Redirection Example 4 Once the connection to the Presidium is established the Password screen is displayed refer to Section 4 4 3 Doc 12384_05 49 Installation and User Manual ADPRO Presidium by Xtralis 50 4 4 2 Setup Utility No Activity Timer The Presidium Setup Utility will automatically disconnect the connection to a Presidium if no mouse movement is detected within a 5 minute period This action is performed to ensure the Presidium s detection is enabled Note When the Setup Utility is connected to a Presidium the following outputs and on screen monitor output displays are not updated This means they will retain and display there last state Target T
117. rucks Target Bounding boxes Trigger areas Contrast level No video alarm Contrast alarm VMD alarm General alarm output Presidium detection is also disabled when Setup Utility is connected 4 4 3 Using the Setup Utility V Enter Password DER Enter Password for Device ADPRO Presidium v Remember password Forgotten Password Figure 41 Enter Password 1 Enter the password Presidium standard Enter the password default admin and select OK Presidium Mini Enter username default admin and password default admin select OK Note that the defaults should be changed to a user defined a new username or password refer to Authentication on page 68 The following screen is then displayed Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual V ADPRO Setup Utility Select Function Please choose the function you wish to perform ALPRO Presidium Setup twee Disconnect ADPRO Presidium Figure 42 Select Function 2 Select the ADPRO Presidium Setup radio button and select Next If this is the first time this Presidium has been connected to the following screen is displayed Change Video Standard Choose the video standard PAL NTSC that matches the cameras connected to the Presidium When you press OK the video standard plus any other changes you may have made will be saved to the Presidium N OK Cancel Figure 43
118. ructure must be provided There is a range of communications media choices available for use such as PSTN ISDN ADSL microwave or RF The type of communications link is dependent upon a number of criteria 1 Existing infrastructure To provide a cost effective solution consider using any existing communications infrastructure at the site subject to it meeting required bandwidth and other operational requirements 2 Backup communications Under some circumstance a secondary communications link may be required if the primary method is negated 3 Availability Consider the availability of different telecommunications options as not all telecommunication solutions will be provided by a single provider or site requirements might exclude certain types of communications 4 Installation and operational cost The installation and operational cost are a major factor in deciding the type of communications infrastructure selected The cost is generally linked to the bandwidth provided on the link 5 Bandwidth requirements The expectation of bandwidth which ultimately drives how quickly video information can be transmitted is extremely important to ascertain Links with throughput of 9600 baud right through to 2 mega baud are available ADPRO video Doc 12384 05 21 Installation and User Manual ADPRO Presidium by Xtralis transmitters are optimised for operation over low bandwidth links however they also provide outstanding operation over hi
119. s connected to that input The Channel Status area displays the settings that have been applied to this channel Selecting the Change button in the Unit of Measure section enables metres or feet to be selected as the displayed unit of measurement Selecting the Change button in the Video Standard section enables PAL or NTSC to be selected as the video standard Important The Presidium detection is disabled when the Presidium Setup Utilty is connected to the unit Once the Presidium has been programmed then ensure that the setup utility is disconnected and displaying the site list refer to Figure 37 Establish Connection to the Presidium on page 47 52 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 4 4 4 System Status The status of the Access Secure input Alarm Inputs and Isolation Input can be determined through the Setup Utility GUI Status information may be useful while commissioning or fault finding a Presidium Access Secure Channels Network Securty status jecur rp Toe TICO Aces SeueSuus Teen UUN Authentication Set the password used for connecting to the Preadum Username adpro V Passwords match When you press the Save to Presidum button the new password wil take ellect Alarm Sealed Alarm Unsealed Channel Status E a hareel Name ackdoor Isolated Isolation with Alarm Input Tamper athe s
120. ser Manual Appendix C Example Site Plan El OFFICE pm caD PROTECTED AREA IR ILLUMINATOR 0 y REPORT ALL ERRORS TO THE TOP VIEW SIDEPOST MOUNT TOP VIEW CORNER POST MOUNT ECTEDAREA SIDE VIEW EXAMPLE SITE PLAN OW CAMERA Tecte io gy ak Meng Lakes Sout Astralia ar VIEW Xtralis ADPRO PRO 250 MOUNTED BEU FRONT VEW 2 5 z T ae n e e e ri H WOI SSIS NILUM S 2 ANGH IM Dei N OST10 NI 03501008438 FELON IER 1I QLYEREL L5 A ENASI 4 1129 40044 SHE SI ONVWYO SHL Doc 12384 05 95 Installation and User Manual 96 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Appendix D System Design and Equipment Checklist Company Date Location Design by Channel Camera Lens Field of Lighting Other Camera No Selected Selected View OK 0 4 Detectors Mounting Cabling Distance Any Special Requirements Doc 12384 05 97 Installation and User Manual 98 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual Appendix E Camera Lens Selection Table 7 Horizontal FOV 20 Metres 66 Feet 1 4 camera format 1 3 camera format 1 2 camera format Max Distance Dead zone Max distance Dead zone Max distance Dead zone metres feet metres feet m
121. signed Subnet mask 255 255 255 O GA Automatically Assigned Default gateway v4 Automatically Assigned Figure 56 IP Address Configuration Note The Presidium IP Address may be dynamically assigned by selecting the Obtain an IP Address automatically DHCP Client radio button if required Presidium Mini has two IP addressses The second IP address is automatically assigned to the next address when static IP addressing is used 66 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 2 Select the Advanced button to display the Advanced Communication screen MINI V Advanced Communications Enter the port the Presidium uses to accept connections This can be any value from 80 to 65535 except port 88 and ports 20001 through 20004 80 OK Cancel Figure 57 Advanced Communication The port used to accept connections may be changed if required By default the port used is port 80 The valid port range is 80 65535 excluding 88 and 20001 20004 The default port should be used in most installations 4 4 7 High Level Interface Tab The High Level Interface HLI only requires configuration if the Presidium is connected to an a MINI FastTrace FastTx FastTrace R or other DVR which supports the Presidium HLI Note The address of the FastTrace FastTx FastTrace R must be programmed in the FastTrace DVR IP address field Warning It should not be necessary to change the port number
122. t Display Display No Video Screen e When No video detected refer to No Video Detection on page 65 Explanation A blue screen is displayed with the No Video icon superimposed if valid video signal is not detected at the channel input Contrast Icon Contrast Alert active refer to Contrast Monitoring on page 65 Displayed when a message is sent to indicate that the video quality is too poor for reliable VMD operation The Contrast icon is superimposed over the video Tamper Icon Alarm Input Tamper active Displayed when a tamper on an alarm input triggers an alarm Isolate Tamper active Displayed when tamper on the isolate input triggers an alarm The Tamper icon is superimposed over the video Alarm Input Icon Alarm Input active refer to Alarm Inputs on page 35 Displayed when the alarm input is in the alarm state Chassis Tamper Icon Sai Secure Tamper active refer to Access Secure Input on page 38 Displayed when a tamper on the access secure input triggers an alarm Video Detection Icon X Video Movement Detection active Displayed when an alarm is generated by video movement in the detection area Alarm Tracks Alarm event active and Alarm Tracks selected refer to Display Alarm Tracks on Video Output on page 54 A target bounding box and track history is displayed from the time that an alarm triggers All Tracks Connecte
123. t bent or damaged 5 Attach the VM15 module to the frame of the Presidium using the retained blanking plate Screw 6 Re attach the lid of the Presidium using the 10 screws VM15 VM15 Video Module Video Module 1 10 Figure 79 VM15 Module Installation Doc 12384 05 87 Installation and User Manual 88 ADPRO Presidium by Xtralis Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual 8 Specifications Table 6 Presidium Specifications Video Inputs 2 independent camera input per VM15 module or Presidium Mini Each input 1 V peak to peak 75 ohm or high impedance Video Outputs 2 independent video outputs per VM15 module or Presidium Mini 1 V peak to peak video output when terminated by 75 ohm load Each video output displays channel video and on screen display information and connects directly to the camera during power failure Inputs per Channel 2 channels per module or Presidium Mini All external inputs are transient protected and designed to be driven by dry contacts or logic levels Voltage input lt 0 8 V logic low 7 ma max between 3 5 V and 5 0 V logic high Screw terminal connectors Normally Open NO Normally Closed NC Single End of Line SEOL or Dual End of Line DEOL tamper detection on each input using supplied resistors Isolate input to disable enable detection no video and contrast alarms Alarm input with programmable hold time Inputs per ch
124. tegy to Remove or Reduce Risks Test and Monitor Strategy 2 3 1 ADPRO Solutions ADPRO provides a range of video security solutions that focus on remote monitoring of facilities but also provide excellent onsite monitoring capabilities The product range features video transmission video recording and video detection systems that link to an industry leading software package VideoCentral for remote management and control A typical approach to security is to provide an indication when an intrusion has occurred ADPRO however recognises the value in being able to immediately identify the cause evaluate the situation and respond accordingly ADPRO s combination of onsite detectors audio video recording and transmission to monitoring stations provides security in a wide variety of markets and application areas Presidium forms an important element of security solutions where automatic detection and verification of an intrusion is paramount 2 3 2 Presidium an ADPRO Solution ADPRO Presidium and Presidium Mini in conjunction with the other Xtralis products are ideally suited for security solutions where the risk is illegal intrusion into a high value asset The Presidium approach provides reliable protection of a perimeter or sterile area with rapid identification of the cause of any intrusion within that perimeter The Presidium system coupled with other ADPRO technologies can form an important link in responding to different scenari
125. the left of the channel number A Presidium Input is unallocated when no name is shown next to the number 9 3 Q9 4 Figure 73 Unallocated Icon The Connect button is used to enable a Presidium Input A green tick is shown and details can be modified To disable the use of an Presidium Input the Disconnect button is used and a red cross is shown For example set Disconnect if maintenance is being performed in that area or the sensor is being replaced 80 Doc 12384 05 ADPRO Presidium by Xtralis Installation and User Manual 5 2 1 Presidium Input Settings 1 Highlight the required channel and select the Configure button to setup the Presidium Inputs MINI Presidium Input 1 Settings Presidium Input Name Presidium Presidium Input Camera View Style Quad zl Figure 74 Presidium Input Settings Presidium Input Name Option 16 characters maximum Enter the name to be associated with this Presidium Input Presidium Input Camera View Style Options Live Quad Factory Default Quad When an alarm is triggered by Presidium the style of display configuration shown on VideoCentral can be preset The Live option is primarily designed for use with access entry exit points A live video feed is displayed at VideoCentral The Quad option captures three alarm images in a user defined period defined under Camera Settings General tab and displays the images at VideoCentral along with a fourth pan
126. ton at any time will cause all settings currently within the Presidium setup utility software to be saved to a file on the PC a confirmation box will be presented to verify the required action Doc 12384_05 69 Installation and User Manual ADPRO Presidium by Xtralis V Presidium Setup Utility DER ADPRO Presidium Setup Channels Network High Level Interface Security Status Channel List Monitor Camera Paddock Connect Front Of Building End Of Building Full Carpark View From Front Foyer Entrace Main Foyer Staff Entrance TestLab Entrance MSSSSSSSSS SS iceeoosonsoNe EB Canteen Hallway Channel Status Channel Name Paddock Camera State Connected VMD Rule OR Unit of Measure Select the unit of measure Metres Feet to be used for displaying and storing the settings Current Unit of Measure Metres Video Standard The Video Standard PAL NTSC should be set to match the cameras connected to the Presidium Current Video Standard PAL LoadiSave ALL Settings Load from File Save to File Print Settings Save to Presidium Disconnect ADPRO Presidium Figure 61 Presidium Setup Screen Save Settings to File Save in Setup Utility 1 0 sl e ES Qiimageformats plugins MyRecent translations Documents E defaults settings My Network File name Places Save as type Presidium Settings Files settings hd Figure 62 Save to File
127. tor Normally Closed SEOL Normally Open DEOL Dual End Of Line Resistor Normally Closed DEOL Doc 12384 05 35 Installation and User Manual ADPRO Presidium by Xtralis 36 Normally Open NEOL Short Circuit Alarm Open Circuit Sealed No Tamper Operation Ground Connection Alarm Input Normally Closed NEOL Short Circuit Sealed Open Circuit Alarm Ground Connection leo e ee e e Alarm Input No Tamper Operation Ground Connection Normally Open SEOL RIKI Short Circuit Alarm Low Impedance Sealed Alarm Input e Open Circuit Tamper Emer e e Normally Closed SEOL RIKI Short Circuit Tamper Low Impedance Sealed Alarm Input Open Circuit Alarm Ground Connection RIKI Normally Open DEOL Short Circuit Tamper Low Impedance Alarm R2K2 Hi Impedance Sealed Open Circuit Tamper Alarm Input A e Ground Connection vw RIKI Normally Closed DEOL Short Circuit Tamper Low Impedance Sealed R2K2 Hi Impedance Alarm Open Circuit Tamper Alarm Input Pa Figure 26 Alarm and Isolate Input Configuration 3 7 Isolation Isolation inputs are provided for each video channel ALM Isolate A and ALM Isolate B These connections allow individual channels to be isolated prevented from generating an alarm This feature is useful in a number of scenarios Commissio
128. tralis 60 Once all required areas have been defined select the Next button The following screen is displayed V Presidium Channel Configuration Channel 1 General CameraCalbration Areas Detection Parameters Alarm Behaviour Video Monitoring Detection Parameters Detection Sensitivity Detection Senskivity M The Detection Sensitivity defines the most difficult intrusion the system is expected to detect The default sensitivities are as follows E Customise Senskivty Low Use this setting to detect general intrusion in open well lit scenes that would include single or multiple targets walking or running Environmental Activity High 3 Medium Use this setting to detect normal or more obvious intrusion including targets crawling walking or running Fl ss sedit y High Use this setting when the detection requirement includes small slow moving crawling or low contrast targets in the horizon Environmental Activity The Environmental Activity tells the Presidium what the general environmental conditions for this scene will be most of the time Very Low Use this setting when the detection area is ideal For high sensitivity VMD detection It will be close to completely sterile evenly lit at night with no tree shadows minimal camera movement and minimal effects From wind rain and cloud Low Use this setting for scenes between Very Low and Medium Medium Use this setting for a typical detection area This w
129. tralis Installation and User Manual Appendix J Presidium Do s and Don ts Do Don t Walk test at day dusk night Install cameras looking into lights IR illuminators Trim foliage regularly Change parameters without testing the system Use PIR terminations barriers Use a FOV of greater than 30m 98ft Check alignment of cameras Check alignment of PIRs Regularly clean camera windows lens Regularly clean PIR windows Route cables neatly Spend time performing a thorough survey Use barriers to prevent light spillage from roads Account for dead zones in site layout and camera lens selection Check target sizes at the foreground and background Doc 12384_05 109 Installation and User Manual ADPRO Presidium by Xtralis 110 Doc 12384_05
130. trigger an alarm event A trigger shape can only be defined within a Detection Area Multiple Trigger Areas can intersect and overlay each other Trigger Shapes provide enhanced target detection capability for example Simple triggers the target crosses one of the boundary lines Directional triggers the target crosses two of the boundary lines Loiter triggers the target crosses one boundary and moves within the area for a preset period or the target simply appears or disappears see Trigger Area Properties Click on Add Trigger Shape or right click on a detection area to add a new trigger shape Move the position of the nodes or Add Nodes to change the size and shape of the trigger area To remove entire shape select a shape and press Remove Shape or right click on a shape A new trigger shape is presented as a square with 4 edges and 4 nodes A small yellow box will define the origin node Each edge of the Trigger Area can be assigned a unique trigger property Entry Edge target track must move into the trigger area Exit Edge target track must move out of the trigger area Crossing Edge target track must cross over the edge line in either direction Disable Edge target track is ignored By default a new trigger area has All edges disabled The Enable Timer set to inactive This means that no timer function is enabled and alarm triggers are only defined by the Edge properties ie target tracks must p
131. tructions 2 7 2 Performance Assessment Detection Tests Presidium as a detection system should initially be configured to ensure detection occurs effectively and then corrective action can occur to limit any nuisance alarms Whilst performing the detection tests it is important to ensure that the tests are adequately documented and described for proper ongoing maintenance A subset of the tests should be performed on a regular basis to confirm correct operation The detection tests should also be annotated on a site plan to highlight the areas where the tests are performed Refer to Site Maintenance on page 26 for a description of the necessary maintenance procedures Site Detection Tests on page 103 contains a table for documenting the detection tests performed and their outcome Prior to performing the detection tests Display all Tracks on Video Output should be disabled Refer to General Setup on page 54 For each detection area the following should be performed Check that the detection area covered by each camera connected to Presidium matches the design and that the detection areas programmed for Presidium are correctly aligned within the field of view of the camera Check that any PIR detector is aligned as initially designed This may require using the PIR tester and software to ensure that the angle of the tilt is correct i e approximately 1m 3ft high at the maximum detection distance as well as the horizontal alignment
132. ue Important Important Important Important It is not recommended the Presidium Mini be upgraded over any type of WAN connection This is because if the link is dropped during the upgrade process the unit may be left in an inoperatable state Upgrades performed over a WAN communications network such as xDSL may take upto 30 minutes to complete Also updates to video images within the Setup Utility can typically take 10 15 seconds Do NOT switch off the power to the Presidium during the upgrade process as it may leave the unit in a non operational state which will require the unit to be returned to the manufacturer for restoration Once the upgrade has been completed reconnect to the unit and follow the process described in Saving a Configuration to File on page 69 to save a copy of the settings This procedure is required as previous saved settings files cannot and should not be loaded Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual 4 6 Troubleshooting 4 6 1 Detection Problems Troubleshooting may be performed using a video monitor connected to the Presidium video output if required If detection is not occurring as expected check the following Ensure that Camera Calibration has been properly performed refer to Camera Calibration on page 56 Ensure that the Detection Areas have been defined as required refer to Areas on page 57 Ensure Trigger Areas have ben positioned
133. um Licence Agreement ADPRO Presidium by Xtralis Accept the terms of the agreement and select Next The Destination Folder screen is Doc 12384_05 ADPRO Presidium by Xtralis Installation and User Manual i Presidium Setup Utility Setup Destination Folder Click Next to install to the default Folder or click Browse to choose another Install Presidium Setup Utility to C Program Files ADPRO Setup Utility 1 01 Figure 34 Choose Setup Type 5 Select Next to install the Setup Utility in the default folder or select Browse to specify a different installation location 6 Select Install The Presidium Setup Utility commences installation 7 Select Finish when the installation has completed A shortcut to the setup utility is placed on the desktop 4 3 Configure the PC Network Connections The factory TCP IP network addressing for the Presidium is 192 168 1 3 The Presidium Mini has two factory IP addresses 192 168 1 3 and 192 168 1 4 The factory subnet mask address is 255 255 255 0 For the PC to be able to successfully connect to the Presidium the PC IP settings must be modified to a class C address on the 192 168 1 x subnet 1 Select Network Connections from the Control Panel 2 Double click on Local Area Connection or other type of connection displayed Doc 12384 05 45 Installation and User Manual ADPRO Presidium by Xtralis 3 Select Properties The following screen is displayed 4 Local Area Connecti
134. ving the Site Records 4 5 1 Saving a Configuration to File 4 5 2 Loading a Configuration from File 4 5 3 Printing the Site Configuration sssssssssessesee eene rennen nns 4 5 4 Upgrading Presidium Software 4 6 Troubleshooting 4 6 1 Detection Problems M CREER ERR 4 6 2 IP Address Forgotten sande age ee eh 4 6 3 Presidium Will Not Connect Presidium Appears in List of Local Units Presidium Does Not Appear in List of Local Units ME 4 6 4 Password Forgotten 4 6 5 HLI Connection to FastTrace Fails to Operate xd sud RC ete e rene EEN 4 6 6 Presidium Setup Utility cannot be Started 5 Connection to ADPRO FastTrace FastTx FastTrace R by Xtralis sss 5 1 Entering the FastTrace FastTx FastTrace R Setup Screen 5 2 Presidium Inputs 5 2 1 Presidium Input Settings Presidium Input Name Presidium Input Camera View Syle Camera Behaviour Setup 5 3 Advanced Communication Pionero T 5 3 1 Presidium High Level Interface Properties 5 4 IP Address Requirements esee eene eene nennen nnn terne nnn nennen nnn nnns 6 Connection to a Third Party DVR eseseeeeesieseiseee een en nennen nennt inna nnn sn nnn the nn nenas tn nnn 7 Adding a VM15 Module 2 ee ence ee eeeenee se eeeeeee sense ense nenne then anne tra anne nne ences nn trn in nen
135. voidable and the positioning of cameras must account for this The placement of opaque material on fences near roads can alleviate most nuisance alarms from lighting Take into consideration the position of sunrise and sunset as well as reflections from objects in the FOV to limit any blinding of the camera due to bright light Do not install cameras facing into bright lights or IR illuminators 7 Cable Selection Typically RG59 standard 75 ohm cable should be used as a minimum requirement In a monochrome system the cable length should be restricted to 250m 800ft before cable compensators are installed Signal degradation due to cable length has a far greater effect on colour video where the coaxial cable should be restricted to 150m 500ft before cable compensators are installed Other Detectors Selection and Location The rationale behind using an additional detection technology is to provide a system that is not susceptible to any one possible cause for nuisance or false alarms i e using complementary technologies to limit false and nuisance alarms whilst maintaining the highest detection probability ADPRO recommends using either long range for perimeter protection or wide angle for area protection Passive Infra Red PIR technology in conjunction with Presidium In many instances using other detection technologies with Presidium is extremely beneficial to provide a double knock scenario Double knock installati
136. wired using shielded cable Connect the shield to the ground GND terminal 8 pin Screw Terminal Connector m 2 2 Wo Pin 1 8 gt ESSI ON ON Ad joo ON d aon ON WIV ou ON WIV oa WOO UL mm BOO WOOD WIV ml No Figure 28 Pinouts for Presidium General I O Connector Doc 12384_05 37 38 Installation and User Manual ADPRO Presidium by Xtralis 5 pin Screw Terminal Connector N go m m m m 4 2 3 4 b M G c EI 7TI ELE e CDD z oz o zo Figure 29 Pinouts for Presidium Mini I O connector 3 9 1 Access Secure Input The Access Secure input pin 2 is used to put the Presidium into the Access or Secure state When in the Access state alarm triggers are disabled for alarm inputs and VMD however alarm input tamper contrast and no video triggers are still enabled unless disabled by the Alarm Isolate When in the Secure state all alarm triggers are enabled unless otherwise disabled by the Alarm Isolate The Fault Relay is not affected by this state The Access Secure input allows the Presidium to be independently set into the Access state of operation This input is usually connected to an alarm panel or access control system The access secure input is tamper protected regardless of the access secure state Note If a tamper is generated on the Access Secure input then all Presidium channels wi
137. wn independent assessment of the fitness or suitability of the products for your purpose You acknowledge that you have not relied on any oral or written information representation or advice given by or on behalf of Xtralis or its representatives Total Liability To the fullest extent permitted by law that any limitation or exclusion cannot apply the total liability of Xtralis in relation to the products is limited to i in the case of services the cost of having the services supplied again or ii in the case of goods the lowest cost of replacing the goods acquiring equivalent goods or having the goods repaired Indemnification You agree to fully indemnify and hold Xtralis harmless for any claim cost demand or damage including legal costs on a full indemnity basis incurred or which may be incurred arising from your use of the products Miscellaneous If any provision outlined above is found to be invalid or unenforceable by a court of law such invalidity or unenforceability will not affect the remainder which will continue in full force and effect All rights not expressly granted are reserved FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency e
138. ximum of 20 channels per Presidium refer to Adding a VM15 Module on page 87 VM15 Modules must be added in order i e slot 1 first followed by slot 2 etc to ensure that camera numbers are correct Each VM15 Video Module incorporates Alarm Input Connectors one per channel This enables alarm sensors e g Passive Infra Red PIR microwave etc to be associated with cameras VM15 VM15 Video Module Video Module 1 10 VGA RS 232 GND Ground ALMA O P Alarm A Output A S Access Secure ALMA ISOLATE AlarmA Isolate FLT N C Fault Normally Closed ALMA I P Alarm A Input FLT COM Fault Common GND Ground FLT N O Fault Normally Open ALM O P COM Alarm Output Common GEN ALM N C General Alarm Normally Closed ALMB O P Alarm B Output GEN ALM COM General Alarm Common ALMB ISOLATE Alarm B Isolate GEN ALM N O General Alarm Normally Open ALMB I P Alarm B Input Figure 19 Rear View of the Presidium Note The VGA RS232 and USB ports are currently not used Doc 12384 05 29 Installation and User Manual ADPRO Presidium by Xtralis 3 2 Presidium Mini Presidium Mini is housed in a metal enclosure suitable for desktop placement or vertical attachment to a wall via two screw mounting tabs Important It is a UL requirement that cabling to a wall mounted Presidium Mini is only from the side or top EH de v Figure 20 Cable Entry Requirements Note When Presidium Mini units are located
139. zone loitering Contrast alarms for sabotage detection No video detection for camera lens or cable failure Easy to commission via quick setup feature Single cable High Level Interface to ADPRO FastTrace ADPRO FastTx and ADPRO FastTrace R reducing wiring and setup time providing seamless integration standard Presidium only External access control input for easy integration into a security system External detection inhibit input to reset all alarms External alarm inputs for integration of other alarm sensors Over temperature alarm standard Presidium only 1 2 Unique Features of Presidium Mini Two channels Small size footprint via desktop wallmount enclosure 12V DC power supply supports battery based operation Doc 12384 05 1 Installation and User Manual ADPRO Presidium by Xtralis 1 3 Installation Steps The following steps must be followed to install a Presidium system Design the system Gather site information refer to Preliminary Information on page 7 Discuss requirements with client Survey the site refer to Site Survey on page 7 Select the equipment refer to System Hardware on page 11 Install the system Commission the system nstall Presidium Setup Utility software on PC refer to nstall Setup Utility on page 43 Configure the Presidium refer to Configure Presidium on page 47 Assess the system performance refer to Performance Assessment on page 25

ADPRO Presidium by Xtralis Installation and User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents