Midland BT City manual
Contents
1. AUX wired connection Music or audio from the AUX wired connection by default it is always in the background also when the intercom is open or during a phone call It is possible to change this beaver following the procedure de scribed in the Setup and Special configuration chapter Pairing to other Bluetooth devices The BTCity unit can be paired to other Bluetooth devices like Phone GPS Navigator or PMR446 Radio with built in or external Bluetooth The pairing procedure must be done using the Volume or the Volume buttons gt Pairing to the Volume button for Phone with music A2DP stereo gt Pairing to the Volume button for GPS navigators and other devices which the audio must be always in background GPS PMR446 Radio gt Phone GPS Attention The Volume button does not support the pairing with a phone and do not support A2DP Stereo Music Using the telephone features The cellular phone can be paired only to the Volume in this way it is possible to manage all the phone functionalities and listen to the stereo music An incoming call has the higher priority that means all other communications will be closed Intercom Music Pairing the unit with a mobile phone 1 Enable the Bluetooth device search feature on your mobile phone As this procedure varies according to the brand and model of the mobile phone refer to the manual supplied to your particular pho ne2. ElectroMagnetic Compatibility EMC standard for radio equipment V 2 2 1 Part 17 Specific conditions for Broadband Data Transmission Systems Electromagnetic compatibility and Radio spectrum Matters ERM A Wideband transmission systems Data transmission equipment 3 2 i EN 300 328 operating in the 2 4 GHz ISM band and using wide band modulation i i techniques Harmonized EN covering the essential requirements of V1 8 1 article 3 2 of the R amp TTE Directive Supplementary information to the conformity assessment result on which the declaration is based Conformity assessment procedures are referred to art 10 4 linked with Annex III of Directive 1999 5 ec The test sample fullfils the requirements specified above on the basis of test result and their evaluation The product herewith complies with the essential requirements of EC Directive 99 05 EC 2004 108 EC and following implements and modifications 2006 95 EC and following implements and modifications 93 97 EC Reference to any marking or other indication e g on the product is exhibited in attachment to this declaration Reggio Emilia 19 11 2013 CTE International srl Responsible of Quality Assurance Giovanni Bo C er A ALL GS This document is owned by Cte International srl It is forbiddeen to reproduce or diffuse it without the authorisation of the Quality Assurance Manager of CTE International srl
3. or Volume button If the GPS is paired on Volume the street voice announcement will interrupted all the other communications Intercom Music If the GPS is paired on Volume all the street announcement will be in background and will not interrupted the Intercom communications Attention If you need to connect both Phone and GPS you must pair the GPS to the Volume 4 button and the Phone to the GPS it self not anymore to the Volume button Attention remember to switch off all the other Bluetooth device only the two devices involved in the pairing must be turned on GPS Navigator with stereo music player If the GPS is also a stereo MP3 player and you want to listen to stereo music you must pair the GPS to the Volume button In this confi guration the GPS street voice announcements will interrupt all other communication Intercom Music When the GPS is paired to the Volume button the Phone mode is activated Attention It is possible to listen A2DP Stereo music from the GPS only in Phone Mode How to pair the BTCity to a GPS In general is possible to pair the BTCity to all the GPS for motorbike that support Bluetooth headset connection To pair the BTCity to a GPS you must first enter the setup mode 1 Turn off the unit 2 Press and hold down the Control button about 7 sec until the Red light is on permanently 3 Now press firmly 3 sec the Volume or Volume b
4. authorized service centre gt The affected product or accessory gt The original proof of purchase which clearly indicates the name and address of the seller and the date and place of purchase This warranty does not apply to accidents of any kind exposure to pressure extreme temperatures outside of 10 C to 55 C submer sion water damage battery leak or abuse This warranty does not include the cost of labor for removal or re installation of the product European CE Notice Certification and Safety Appro vals Information This product is CE marked according to the RTTE Directive 99 5 EC and is free use in all the EU countries Users are not permitted to make any changes or modifications to the device Modifications which are not expressly approved by the producer inva lidate the warranty card For further information please go to our website www cte it 13 All articles displaying this symbol on the body packaging or instruction manual of same must not be thrown away into normal disposal bins but brought to specialised waste disposal centres Here the various materials will be divi ded by characteristics and recycles thus making an impor tant contribution to environmental protection Alle A rtikel die auf der V erpackung oder der G ebrau chanweisung dieses Symbol tragen d rfen nicht in den normalen M lltonnen entsorgt w erden sondern m ssen an gesonderten Sammelstellen abgegeben werden
5. button down for approximately 3 seconds until the BLUE indicator lights Switching the unit off gt Press and hold both Control and VOL buttons together for ap proximately 3 seconds until the RED indicator flashes 3 times thus lessening the chances that you might turn off the unit accidentally especially whilst wearing heavy gloves Adjusting the volume Your Midland BTCity uses AGC technology which automatically adjusts the listening volume in relation to background noises However it is also possible to manually adjust the volume by means ofthe Volume and Volume buttons Attention volume can be adjust only when an audio connection is active Operative mode The BTCity can operate in two main mode Intercom and Phone The function button on the unit can have different functionality de pending on which mode the unit is at that moment gt n Intercom mode the Control button lets you manage the communication gt In Phone mode you can manage your Bluetooth cellular phone to place answer a phone call or to listen to the music in stereo mode Please use your phone responsibly and safely You can switch toggle from one mode to the other simply pressing the Middle button for 3 seconds A voice announcement will tell in which mode you are on The toggle sequence is the following Intercom mode if another unit has been paired gt Phone mode if a phone has been paired Every time you tu
6. for 3 Seconds If your mobile phone supports voice calls you will be asked to speak the name of the contact you wish to call Priority Calls have a high priority which means that all other commu nications are temporarily disabled when a call arrives and automatically re enabled once the call ends Ending a call There are several ways to end a call Waitforthe called person to end the call Press the Control button for 3 seconds you will hear an audio confirmation tone Press End button on the mobile phone Using the MP3 player feature of the mobile phone Many mobile phones are now designed to be used as stereo MP3 players The BTCity device fully supports the A2DP and AVRCP proto cols that enable you to listen to stereo music and remotely control your mobile phone s MP3 player You can even use the buttons on the BTCity unit to control the following play options Play Pause Forward and Backward Volume forward Volume backward Control Pause Play Available controls gt To play pause music click the Control button gt To skip forward to the next song keep pressed the Volume button To skip backwards to the previous song keep pressed the volume button Priority the music listening mode has the lowest priority Therefore it Will always be disabled when another type of communication is ena bled Pairing to a GPS navigator The GPS can be paired to the Volume
7. for further information 2 Press and hold down the middle button about 7 sec until the Red light is on permanently setup mode Now press for 3 seconds the Volume button the Blue and Red light will flash 3 After a few seconds the mobile phone will display Midland BTCi ty Select it and follow the instructions provided in your mobile phone manual to accept the pairing When prompted enter the pairing code which is 0000 four zeroes Your mobile phone should then display a confirmation message if the pairing opera tion has been successfully completed 4 The BICity will automatically exit the set up mode red indicator on and go to the working mode blue light flashing Answering a call When you hear the phone ring you can answer in two different ways Vocally Simply say one word to answer the call and start talking Manually Tap the Control button and start speaking Rejecting a call If you don t wish to answer you can let the mobile phone ring or press the Control button for 3 seconds you will hear one audio confirma tion tone Making a call There are several ways to make a call From the mobile keypad Dialthe number on the mobile keypad Press Send on the mobile phone To redial the last number gt Press and hold Volume button for 3 seconds in order to redial the last number you will hear one audio confirmation tone To make a voice call Press Volume button
8. microphone with boom and wire microphone 2plates with bi adhesive strip to fix the unit onto the helmet gt 2clamps to fix the unit onto the helmet gt 2 stereo audio cables to connect an iPod or other models of MP3 players gt 1 miniUSB wall mounting power supply with double plug Wind Suppressing Foam Microphone Cover Allen key and Velcro strip for assembly The units included in the TWIN kit are already paired and can therefo re be immediately used in the Intercom mode Technical specifications of Midland BTCity General gt Bluetooth ver 2 1 stereo Headset Handsfree A2DP protocol AGC system automatically controls the volume in relation to background noise Voice VOX or manual communications option Manual controls to enable telephone intercom and wire con nection gt Fully waterproof gt Lithium battery with 8 hours talk time Recharge time app 4 hours Bluetooth connections gt Identical device for Rider to Pillion or Bike to Bike Intercom mode up to a maximum range of 200 meters With BT Remote for easy to use handlebar commands Bluetooth devices Mobile phone with MP3 player Stereo A2DP protocol GPS spe cific for motorbike PMR446 transceivers with built in or external Bluetooth con nection for group bike to bike communications Wire connections gt For stereo audio input iPod MP3 player For PMR446 transceivers with optional cable Attention before usin
9. D ort werden die Materialien entsprechend ihrer Eigenschaften getrennt und um einen Beitrag zum Umweltschutz zu lie fern wiederverwertet Cte international EC Certificate of Conformity The World in Communication to EC Directive 99 5 2004 108 2006 95 EC Signature DO 7 1 4 4 Rev 5 Authorised on 02 02 2010 By S Peterlini CE DECLARATION OF CONFORMITY N 2013111905 Rev 4 Manufacturer C T E International S r l Address Via Sevardi 7 ZONA INDUSTRIALE MANCASALE 42124 REGGIO EMILIA Products Name BT CITY Product Type BLUETOOTH HEADSET INTERCOM Brand MIDLAND The product described above is in conformity with the following Specifications based on sample testing Item of Standard Title Edition 99 05 CE or ue of zia EN 60065 2002 Audio video and similar electronic apparatus Safety requirements 5503 A1 2006 A11 2008 A12 2011 Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related 3 1 a EN 50371 to human exposure to electromagnetic fields 10 MHz 300 GHz 2002 General public Electromagnetic compatibility and Radio spectrum Matters ERM 3 1 b EN 301 489 1 ElectroMagnetic Compatibility EMC standard for radio equipment V 1 9 2 and services Part 1 Common technical requirements Electromagnetic compatibility and Radio spectrum Matters ERM 3 1 5 EN 301 489 17
10. abled and remains active until you press the Control button again You will hear 1 audio tone when the Intercom feature is enabled and 2 audio tones when it is disabled Voice activation VOX gt This is enabled by default To start an Intercom communication simply start talking The communication will remain active for all the time you are talking gt If there is no conversation the Intercom is automatically closed after 40 seconds Attention If needed you can disable the VOX feature simply by pressing the Volume button for 3 sec A voice announcement will advise you when the VOX is disabled To turn the VOX on again just press the same button and a voice announcement will advise you that the VOX is now active This setting is remembered also in you turn off the unit How to pair the BT City to previous BT line unit The BTCity is compatible with all the BT line unit from Midland You can pair the BTCity to a BT2 BT1 BTX1 BTX2 or BTNext unit and the max distance of the intercom is defined from the lower possible To pair the BTCity to another BT line unit you must first enter the setup mode 1 Turn off the unit 2 Press and hold down the Control button about 7 sec until the Red light is on permanently 3 Now press long 3 sec the Control button the Blue and Red light will flash 4 Follow the procedure on the other unit s instruction manual nor mally you can use the Volume button on a
11. anges are confirmed 6 If needed you can adjust again the sensitivity repeating the steps from point 2 otherwise exit the Setting mode by double clicking the Control button Once the red light turns off the blue led starts blinking Now you can use your BTCity Disabling the VOX feature Intercom and telephone Follow all the procedure described in the previous steps and choose the option 1 VOX disabled You will see the blue led blinks once Wired connection always on This feature let you keep the wired connection always on even when the phone or the intercom is open This feature can be useful when you connect a PMR446 transceiver Enabling Enterthe Setup mode gt Press the Volume and Volume buttons for one second The blue LED will flash once gt To exit the Setup mode double press the Control button Disabling Follow the same procedure up described now the blue LED will flash three times gt Toexitthe Setup mode double press the Control button Recommendations for specific uses The section that follows provides a few useful suggestions on how to achieve maximum performance from your BTCity unit Using a PMR446 transceiver To be able to use the transceiver it is necessary to purchase a specific cable sold separately in order to connect the radio to your Midland BICity Some manufacturers radios use a different pin configuration so we recommend that you ask your deale
12. bling the VOX feature Intercom and telephone The Intercom feature can be enabled both manually and vocally VOX The VOX activation is influenced by the background noise and therefore by the speed For optimum results it is possible to choose one of the following four microphone sensitivity levels high medium low and very low The default setting of BTCity is high It is also possible to disable the VOX feature in order to activate the Intercom and phone call answering features in manual mode only Adjusting the sensitivity of the microphone VOX 1 Enter the Setup mode Switch your BTCity off Press and hold down the central button Control until the red indicator switches on permanently Your BTCity is now in Set up mode 2 Press the Volume and Control buttons till the red indicator will turn to steady blue 3 Now press Volume or Volume to increase or reduce sensi tivity Every time you press the Volume buttons the RED light will flash for confirmation When you reach the end of the upper and lower limit the RED light will not flash 4 Double press the Control button the Blue light will flash several times in order to let you know the selected sensitivity once VOX disabled Twice low sensitivity 3 times Normal sensitivity 4 times high sensitivity 5 times very high sensitivity Default high sensitivity 5 Thelight indicator is now back to steady RED Set up mode and the ch
13. er Intercom Communication amp Entertainment System Instruction Guide r2 TEPRAN NT 3 Bluetooth INDEX Midland BTCItY m M GA 2 Charging batteries Me 3 Description of the unit and installation brackets eesesssessesesosoesescsosoescoceosoesescssesseosoesssosossesesosoeoesosossesesossssesossssosossesesososo 3 Switching your Midland BTCity on and off i e oom en rn id eani eh hk kk an eu kk YER YO RAE EY kb LEER Y HERE EA EH REVO Ha 5 PR ipud e 5 Operative Mode sciicusceiro ira ER XODRURKREMO XX ERE EE EAR ER REOR GLEN ERNRENEERGAR FERRE ssis BSE VE CSV MY HURRE GEEK PKRENERKUEEKE EAR REKRO DAR LER ONERE REA 5 IPIS ETT TTL ILT m 5 Pairing to other Bluetooth devites cessi ptor ipn vid n rir ei Fd rl n rd ea PYS NOE POR PUER UR HDUVUR NEAR REV ERAUXU DUC OF 6 Resetting all paired GOV ICOS 9 Special COMMGUMATIONS me 10 Pairing toa BT RONG me 10 Recommendations for specific USes P s 11 ura dug D H 13 LUEGO TTD T TI LLLI TIL LLLI ID 13 Midland BTCity f
14. f the wired connections gt Charger jack enables to recharge the unit using a standard mini USB power supply and firmware upgrade via PC connection Audio kit jack enable to connect an audio kit stereo headset and microphone Auxiliary audio jack AUX can be used to connect an audio source like a stereo iPod MP3 player or PMR446 transceiver Description of the audio kit The audio system includes two ultra flat stereo speakers and two in terchangeable microphones which are both supplied with a bracket and wire connection Fixing the stereo speakers The two stereo speakers have a Velcro adhesive strip that aids their fixing to your helmet The microphone can be fixed onto the helmet in two ways Boom Microphone Place the section with the Velcro adhesive strip between the padding and the rigid cover of the helmet so that the microphone is correctly positioned in front of your mouth and that the white symbol is facing your mouth This type of microphone is suited for Open Faced and Flip Front helmets Wire microphone Using the Velcro adhesive strip place the microphone inside the hel met in front of your mouth This type of microphone is more suited for Full Faced helmets The mini connector on the microphone allows you choose the microphone that best suits the helmet you are using Audio kit jack The audio kit must then be connected to the central jack of the Midland BTCity unit using the L shaped connect
15. g BTCity for the first time remember to recharge it for at least 5 6 hours Attention Midland BT City is designed to withstand rain and wa ter However if it is raining always verify that the rubber caps protecting the sockets are fully fitted Charging batteries Make sure that the unit is fully charged before use Allow at least 5 6 hours for a full charge before using the unit for the first time Normal ly after the first time it takes 4 hours for a full charge Charge the unit by inserting the wall charger into the charging socket lift the rubber cover to insert the plug gt The red LED on the unit will start flashing when charging begins Allow the headset to charge until the blu LED turns on When the charge is complete blu LED on release the headset from the charger Attention everytime the mini USB recharging plug is inserted the device is automatically turned off To use it while it is in charge you should turn the device on with the plug already inserted Description of the unit and installation brackets Volume Volume Control The BTCity has 3 multifunction buttons and 3 wired connections in the lower section Description of the button features gt Control can be used to enable disable the intercom and manage mobile phone features Volume enables you to increase the volume Volume enables you to decrease the volume Auxiliary audio jack AUX Description o
16. have fixed your BTCity on its suitable tool and have inserted the audio kit plug into the central socket wear your earwarmer headset 12 Now fix the BTCity on the Velcro band Wear your headset insert the connection cable of the headset into the BTCity device and wear the helmet Use at your own risk The use of the headphone headset will impair your ability to hear other sounds and others around you Listening to music or speaking on a telephone may prevent you from hearing others around you and distract you from riding safely The use of such headphone headset while riding or skiing may endanger you and others and its use in some areas could not be allowed Using this headset at a high volume may result in permanent hearing loss If you experience ringing in your ear or any other hearing related pain reduce the volume or discontinue using this device With continued use at high volume your ears may become accustomed to the sound level which may result in permanent damage to your hearing Please use this device at a safe volume level Warranty Midland will repair or replace at its option without charge any BT CITY EVA device which fails due to a defect in material or wor kmanship within TWO Years following the initial consumer purchase In the event of a product defect please return it to the authorized customer service or to the Manufacturer himself To make use ofthis warranty it is necessary to return to the
17. he BTSki Audio Kit accessory optional as shown in the figure Please be sure to have placed the microphone This optional kit is the Bluetooth solution designed for winter sports ALUMS SITE Waly wita Ie ASPICE sigh oriented towards Your mouta use without helmets or with semi rigid type ski helmets The audio system is made up of two ultra thin stereo speakers and a boom mike all contained in a soft material lining The audio system includes two ultra flat stereo speakers and one mi crophone with boom all assembled into a earwarmer headset Using the BTCity with a semi rigid helmet To place the BTCity into a semi rigid helmet you should first of all remove the little triangular pads used to cover the ears in most of helmets on sale and then put your helmet directly on the earwarmer headset audio system Be sure the BTCity unit is placed between the two V shapes strap Fitting and removing your Midland BTCity The BTCity can be easily fitted by sliding it downwards so that it fits into the slot of the fixing device BICity is maintained in position thanks to the fixing clip located on the upper section A To detach the BTCity simply press the fixing dip and push the unit upwards If your helmet is not equipped with the two removable pads you could anyway mount your BTCity system by using the supplied Velcro band Be sure to fix the Velcro band as shown in the figure Using the BTCity without helmet After
18. herefore always be disabled when another Bluetooth communication is opened Using a i Pod MP3 Player Listening to music To listen to music from the wired input connect the audio source using the cable supplied with the BTCity unit The volume level is au tomatically adjusted by the AGC system which means that you only need to adjust the volume of your iPod MP3 player to a level that will allow you to listen to music in normal speed Attention never set the volume of the MP3 Player to the maxi mum possible Hint We recommend that you perform a few tests adjusting the volume of your iPod MP3 player so at the normal speed the Headset volume is suited to your needs The AGC system will automatically increase the volume on higher speed Make a note to remember this setting for future trips Attention the volume adjustment Volume and Volume buttons cannot be used to adjust the volume of the wired audio source eg MP3 player Enabling disabling the wire input The wire input can be enabled and disabled Enabling double click the Control button you will hear one audio confirmation tone gt Disabling double click the Control button you will hear two audio confirmation tones Using a Two Way Radio transceiver To be able to use the transceiver it is necessary to purchase a specific cable sold separately in order to connect the radio to your Midland BICity Some manufacturers radios use a diffe
19. ll the previous BT line units like BT1 BT2 5 When successfully paired each unit will have the Blue light on for one second and than go back to the setup mode Red light always on If you don t have more devices to pair you must exit the setup mode from both units before you can use them for BTCity double click on the Control button the Red light will turn off and the Blue light will start flashing For the other devices of BT line please refer to their own user manual Resetting all paired devices Sometimes you may find it necessary to delete all the pairing referen ces stored in the BTCity unit reset operation Toperform this operation first switch off the BTCity and than keep pressed the control button The red led turns on gt Simultaneously press and hold down the Volume and Volume buttons for 3 seconds The Blue Light will be lit on for 1 sec This procedure deletes all the paired Bluetooth devices stored in the memory and it is therefore possible to start a new clean pairing session Using the wired audio input Your Midland BTCity is also supplied with a wired audio input labeled AUX that can be used to connect an audio source like an iPod or any other MP3 Player or a PMR446 transceiver for communications in group or for a coverage increase Priority the wired audio input has the lowest priority when compared to the other Bluetooth connections including the Intercom and will t
20. or Description of the installation brackets The Midland BTCity can be fixed onto the helmet in two different ways By either using the plate with bi adhesive strip or the clamp These methods allow you to safely fix the BTCity unit onto your helmet and to remove it at any time in order to recharge or store it Plate with bi adhesive strip The fixing plate has a bi adhesive strip on one of its sides To fix the plate in place dean the application area on the helmet surface remove the bi adhesive film and place the fixing plate on the helmet by keeping it contact with the surface for a few seconds 3 jj os Clamp Using the Allen Key loosen the two screws on the clamp and place the rear plate between the helmet padding and the external rigid protec tion Then tighten the two screws in order to firmly fix the clamp in place Inside the clamp is included a small plastic spacer that can be removed to close tigher the clamp Fitting and removing your Midland BTCity The BTCity can be easily fitted onto the helmet by sliding it downwards so that it fits into the slot of the selected fixing device plate with bi adhesive strip or clamp BTCity is maintained in posi tion thanks to the fixing clip located on the upper section A To detach the BTCity simply press the fixing clip and push the unit upwards Switching your Midland BTCity on and off Switching the unit on gt Press and hold Control
21. phone functionality Using the intercom feature To use the Intercom feature be sure both BTCity units are turned on and previously paired together The two units supplied in the Midland BTCity TWIN Pack are already paired and ready for use which means that it is not necessary to per form this procedure If the devices are not part of the same pack or one of the BTCity units has been purchased separately you need to pair them in order to be able to use the Intercom function Pairing with another BTCity device 1 Turn off the unit Press and hold down the middle button about 7 sec until the Red light is on permanently 2 Press the Control button on the first unit until the RED and BLUE lights begin to flash rapidly and alternately 3 Then press the Control button on the second unit until the RED and BLUE lights begin to flash rapidly and alternately 4 Now both BICity units are trying to pair to each other When successfully paired the blue led of each device will light for 1 secand go back to setting mode red light always on waiting for additional pairing or setting procedures 5 Touse the two devices exit the setting mode Double click on the Control button The red light will quit and the blue light will be gin to flash Now you can use your BTCity Intercom The Intercom feature can be enabled in two ways Manual activation Press Control button on one of the two units Communication is en
22. r as to which cable is best suited to your needs To communicate via the attached radio press the transmission Press Top Talk PTT button to speak and release it to listen It is not possible to talk and listen simultaneously The cable connected to the transcei ver has a PTT button that can be placed on the handlebar of your bike or held in your hand If you are the pillion rider Adjust the volume of the transceiver to your needs remembering that the volume adjustment is controlled by the automatic AGC system and that it will therefore be automatically increased in relation to background noise If you wish to use a PMR446 transceiver for group communications and simultaneously maintain the Intercom feature enabled between two BTCity devices you must remember that the Intercom feature is enabled every time you speak by means of the BTCity s VOX feature Consequently radio communications will be disabled whilst you are talking with somebody because they have a lower priority compared to Intercom communications This can be prevented by enabling the Wired connection always on or Disabling the VOX feature both explained in the previous section Disable the VOX feature as explained in the previous section to make sure that the intercom will not automatically be activated when you speak on the PMR446 To enable the Intercom feature when using this configuration you will have to press Control button manually 11 Using t
23. rent pin configuration so we recommend that you ask your dealer as to which cable is best suited to your needs To communicate via the attached radio press the transmission Press To Talk PTT button to speak and release it to listen It is not possible to talk and listen simultaneously Communications can be activated also without pushing the PTT button by enabling the VOX function Special configurations Some Midland BTCity features can be configured to suit specific needs Pairing to BT Remote Adjusting Disabling the VOX feature Intercom and telephone Wired connection always on 10 Pairing to a BT Remote Unit When paired to a BTRemote unit you will have available all the 5 buttons of the remote unit When you are in Intercom mode gt Press short the Control button to open close the intercom When you are in Phone mode gt Press short Forward button voice dial answer incoming call gt Press long Forward button dial last number reject incoming call gt Press short Control button Play Pause music When the music is playing Press short Forward button forward a song gt Press short Backward button backward a song gt Press short Control button Play Pause music In all mode Intercom or Phone gt Press long Backward button enable disable wired AUX input Press very long Backward button 7 sec enable disable Vox Adjusting Disa
24. rn on the unit the default mode is Intercom if it was previously paired to another unit otherwise it will be Phone If was paired to a phone If you need to know in which mode the unit currently is just press the Volume and Volume button together for 3 second A voice announcement will tell you the current mode Priority The BTCity manage the different connection audio sources based on the following priority rules Changing of the operative mode Every time you change mode long press of the middle button to tog gle between Intercom Phone the previous audio is closed and the control goes to the new mode Intercom The Intercom has always a higher priority against the music inclu ding Phone GPS in music play mode Every time you open the inter com the music from a Bluetooth source is stopped Only the audio Music from the AUX wired connection is always in background by default Phone calls The phone call has always the higher priority and will interrupt every connection like music intercom Only the AUX wired connection can be still on if the setting Wired connection always in background was enabled GPS voice announcement When the GPS is paired to the Volume button high priority the street voice announcement will always interrupt the intercom When paired using the Volume button lower priority the voice announcement are always in background also if the intercom is active
25. rom vers firmware 14 03 13 Thank you for purchasing the Midland BTCity the wireless intercom multimedia system for bikers The Midland BTCity is designed to be fit ted directly on to your helmet and to be used for communications with Bluetooth devices like mobile phones GPS Sat Navs and MP3 players If desired it can also be paired with another Midland BTCity unit and used as wireless Rider Pillion Intercom system or Rider to Rider in bike to bike mode within a maximum range of 200 meters The Midland BTCity is also supplied with a wired connection that can be used to connect an iPod MP3 player or PMR446 transceiver which will then enable bike to bike communications up to a maximum range of 5 km Midland BTCity is available in two versions gt Single BTCity Intercom kit with one unit only BICity Intercom TWIN with two units Depending on the model purchased the package contains the fol lowing parts BTCity gt 1BICity communication unit gt Taudio kit with two stereo speakers microphone with boom and wire microphone gt 1 plate with bi adhesive strip to fix the unit onto the helmet gt 1clamp to fix the unit onto the helmet gt 1 stereo audio cable to connect an iPod or other models of MP3 players gt 1miniUSB wall mounting power supply Wind Suppressing Foam Microphone Cover Allen key and Velcro strip for assembly BTCity TWIN gt 2BICity communication units 2audio kits with two stereo speakers
26. utton the Blue and Red light will flash 4 Enable the Bluetooth device search feature on your GPS 5 After some seconds Midland BTCity will be displayed on your GPS 6 Follow the pairing procedure of your GPS If a pin code is requested you must enter 0000 four times zero 7 When successfully paired the Blue light of the unit will be on for one second and then the unit will exit the setup mode and switch to the working mode the Blue light will start flashing You can now use your BTCity and the GPS street voice announcement are always in background If you pair the GPS to the Volume button because for example the Volume button was already used you loose the possibility to pair the phone to the BTCity unit You can overcome this limit by pairing the phone directly to the GPS and then the GPS to the BICity unit All the phone features are therefore managed by the GPS itself How to use a GPS When paired using the Volume button the GPS will be automatically connected and the voice announcement are always in background also if the intercom is active When the GPS is paired to the Volume button the street voice an nouncement will always interrupt the intercom In addition remember to switch to Phone mode in order to listen and control the music play pause backward and forward If the phone is connected through the GPS you must use the control buttons on the GPS screen in order to control the
Download Pdf Manuals
Related Search