SR-NF905 5in Diamond Microdermabrasion
Contents
1. Inflected skin Do not use on the following areas 1 Sensitive skin 2 Skin rash 3 Damaged inflamed or infected skin 4 Surgical scar that is less than 12 months old 5 Swollen skin 6 The probes should not point directly towards the eyeball 7 Do not use on the genitals amp Cold amp Hot Function The cold treatment is specially designed to calm down the skin after diamond microdermabrasion or chemical peel The skin is sensitive after peeling treatment so the cold treatment procures is necessary The hot treatment is designed for the acceleration of product absorption Operation instruction 1 Connect the cold and hot hammer to the cold amp hot socket 2 Set microdermabrasion ultrasound timer then press the hot amp cold hammer button You will hear the fan turn on 3 To start the cold function press the button on the hot cold head piece down The metal on the cold hammer side will get very cold 4 To start the hot function press the button on the hot amp cold hand piece up o You will only hear the fan speed up The other side of the hammer will get hot but not extremely hot 5 Wait 2 3 minutes foe the hammer to get cold or hot before starting treatment 6 The treatment should be approximately 5 10 minutes Do not stay in one area of the skin too long this will avoid any damage to skin from the hot amp cold head 7 Press the hot amp cold button on panel again to turn off 8 Clean head before an2. d after every treatment wiping with alcohol a disinfection wipe Ultrasonic Operation instruction 1 Connect the face eye electronic into the ultrasonic electrode outlet 2 Set the ultrasound timer 3 Press the intensity level button up or down for intensity desired for facial work low to mid intensity is recommended 0 4 For body work mid to maximum intensity is recommended 5 9 4 Press pulse or continuous wave indicator light 5 Press the button start or stop Safety warming Do not treat eyelid directly Treat just below the eyebrow and brow bone Never stop the electrode on the skin in one spot Always keeps the electrode moving across the skin Never point the electrode towards chest area Eee e Clean lightly the popping head with cotton Do not rinse it with water be careful not to drop or crash 6 Pregnant patient with disease of blood vessel heart skin bleeding amp trauma are prohibited to use ultrasonic 4 Skin Scrubber Operation Please do not turn on usage with long time better use scrubber within 15 30 minutes per time Then stop the scrubber for 20 minutes before the next scrubber operation Long time operation will burn the scrubber gray box and destroy the control board of the whole machine 1 Make sure the main power button are on 2 Press the skin scrubber timer button then set the skin scrubber intensity using the up or down buttons Always consider the clients comfort leve
3. SR NF905 5in Diamond Microdermabrasion Dermabrasion Photon Scrub User manual 5 functions Micro Dermabrasion Coil amp Hot Treatment Ultrasonic Photon Skin Scrubber Time Display Power Switch Scrubber Ultrasonic Exchange Adjust intensity for Scrubber Ultrasonic O Diamond ON OFF Ultrasonic Output B A Photon Output CGI Le A O _cotianor ON OFF Cold amp hot Output t y Vacuum Meter 7 A Vacuum Output e We Intensity knob for a Vacuum Conductive probe Intensity knob for Photon Ultrasonic Output Scrubber Output Function amp Operation Contents function amp treatment DQQ46 1 Finish all accessories connection before plug the power cord Do not plug the accessory power wires to the sockets when the machine powers are on 2 Be sure the main power swith on the top of the face panel is on set the time Diamond press ON diamond on off to start adjust the intensity knob for the suction you want press OFF diamond on off after use Cold amp Hot turn on the panel power HOT amp COLD press the power button on the hot amp cold hammer turn off both power buttons after use Ultrasonic amp Skin Scrubber set TIMER and adjust the INTENSITY press scrubber START STOP to stop after use Ultrasonic amp Skin scrubber can not work at the same time press ULT or SCR for exchange OUTPUTS BA to control the 2 probes of ultrasonic The ultrasoun
4. d flat probe amp pointed probe can not work at the same time Choose B or A for exchange for the output Caution please do not turn on usage with long time better use scrubber within 15 30 minutes per time Then stop the scrubber for 20 minutes before the next scrubber operation Long time operation will burn be scrubber Grey box and destroy the control board of the whole machine 3 Photon be sure the main power switch on the top of the face panel is on Refer to contents function amp treatment 5 power cord then disconnect and clean accessories 1 Diamond Microderbrasion Function The Diamond Microdermabrasion provided a non surgical skin refinish procedure by using sterile diamond heads to abrade or rub off the top skin layer then Vacuuming out the particles along with any dirt and dead skin back up This procedure removes skin debris imperfection blemishes wrinkles and unwanted Micordermabrashion accompany with skin products that penetrate through top skin layer that reach the dermis level helps to replenish natural nutrients restore cell activity and promote skin health The results after Diamond Microdermabrasion treatment is usually a healthy glowing beautiful skin Accessories O 7 5 a X 3 PVC hose Rubber rings Big cotton Small cotton Color Box amp Fuses filter filter Preparation before treatment 1 A consultation included the examination of the skin a plan for treatment 2 Operation should wear
5. ifferent directions to prevent streaking lines as in the reference picture Brush stock or polishing motions may be used in different sites 7 After treatment brush off all remaining dead skin with a soft brush and rinse with damp sponges or damp cool towel 8 Allow skin to dry then apply desired skin product 9 To clean the diamond head use toothbrush or cotton swab damped with a little alcohol to wipe off the dirty impurity and then use UV light or high temperature for sterilization DIAGAM OF SUGGESTED MOVEMENTS AND AREAS FOR DERMABRASION Diagram of Diamond Dermabrasion Tips amp Wands Set 2 stainless steel wands which are used with 9 interchangeable diamond tips Body Especially for acne knee elbow areas and striae of pregnancy Face For the large blemishes For Scars fine lines and imperfections Used on the eyes and both sides of nose For wrinkles oil tablets blackheads and acne After the D tips peeling procedure use this smooth tip to vacuum clear away the dead abraded skin 1 Clean diamond tips with alcohol then sterilize them with UV light or high temperature 2 Replace the big cotton filter inside the vacuum connector after every five to six treatment 3 Replace the small cotton filter on the wand head after every treatment Safety Warming Never operate this equipment on a person that suffer form the following A Heart disease B Sensitive skin C Damaged sk n D Inflamed skin E
6. l You can increase the intensity when needed 3 Press the skin scrubber on off button You will hear the scrubber start to tick 4 Choose pulse or continuous current according to your needs You will hear different between pulse and continuous current amp Photon Operation 1 It is not recommended to put the probes on a same position for long time Probes may move on the skin in regular line or circle 2 Chose the proper spectrum reaching different depth on skin NOTE 1 Before use choose color according to the skin status 2 The unsuitable setting may cause rubefaction on sensitive skin When this occur can use the cold side of cold amp hot hammer to cool down the area The rubefaction will disappear in 24 hours Photon function can be combined with micro electric current which will make the phnton function more effective 3 The micro current should be MIN at the beginning then adjust it strong according to customer s needs Ps the long stick is use for electric conduction when we do the ultrasonic and the skin scrubber we need to connect this to transfer the microcurrent so the head can work well
7. vinyl gloves and a facemask 3 On oily or acne skin a steamer may be used prior to the cleanser 4 Cleansing the skin with cleaning gel or water then wipe off with cotton pad Allow the skin to dry Operation instruction 1 Connect all accessories to the machine 1 Unscrew the vacuum connector make sure a big cotton filter is in the center amp a large black ring is around connection head 2 Screw down the connector after check Then attach the PVC hose to the connector 3 Place the other end of PVC hose in the end of wand 4 Place a small cotton filter on the head of wand a small black ring is around the head 5 Screw the diamond tip into the wand 2 Put the plug into the power socket and turn in the power button Turn the intensity knob to left side 3 Adjust the vacuum intensity slowly from minimum to maximum the vacuum meter will show the date of pressure For commonly use do not set the intensity to maximum unless necessary Recommended Vacuum intensity in treatment area Treatment area Normal skin inHg Sensitive skin inHg 4 treatment schedule table Treatment Frequency Total Visits 5 Place the diamond had on skin surface start from forehead proceed with a slow sliding motion Do not leave the diamond tip at on spot for too long doing so will cause harm to skin 6 Gently stetch the skin with thumb and finger and glide the hand piece 2 to 3 times over the area being treated Then cross again in d
Download Pdf Manuals
Related Search