user`s & installation manual
Contents
1. Exposures 1 a in E a lise a in n 1m s 3 Once all images have been captured click Done 30 Planmeca ProSensor Digital Radiography System User s Manual USING THE PLANMECA PROSENSOR SYSTEM 7 2 3 Patient positioning 7 2 4 Positioning the sensor Ask the patient to sit down Place a protective lead apron over the patient s chest Paralleling technique recommended Long axis ae Sensor of the tooth The sensor is placed to a sensor holder which is used to align the sensor parallel to the long axis of the tooth Use a long cone for the paralleling technique Bisecting angle technique optional Long axis of the tooth NOTE NOTE The patient holds the sensor in place with his finger The X ray beam is directed perpendicularly towards an imaginary line which bisects the angle between the film plane and the long axis of the tooth The use of the plastic cover is not necessary because the sensor can be sterilized with liquid The sterilization must be done after each patient Be very careful not to put excessive pressure on the sensor Do not place a clamp on the sensor Do not take occlusal exposures with the sensor and advise the user not to bite the sensor Never clamp the sensor package or cable with a hemostat or an unmodified Snap a ray holder Make sure the Planmeca ProSensor system is2. Logarithmic Mapping DICE 25 Original B030 v Midtones Gamma 1 00 mm Midtones Gamma Midtones Gamma Set Defaults Set Defaults Set Defaults 20 Planmeca ProSensor Digital Radiography System User s Manual USING THE DIDAPI CONFIGURATION SOFTWARE 5 2 Configuring Planmeca ProSensor settings 5 2 1 Auto exposure threshold values Ethernet interface If the Planmeca ProSensor Digital Radiography System is used with some other intra oral X ray unit than Planmeca Intra the sensor threshold values can be adjusted for the used X ray unit Change these values only if necessary The threshold value affects the detection sensitivity of the the start of exposure Increase the threshold value if the sensor appears to be too sensitive i e it triggers and takes exposures without radiation Decrease the value if the sensor fails to detect an exposure If the settings have been changed the Apply button becomes active To save the new values click Apply The factory default values can be restored by clicking the respective Set Defaults button Clicking OK quits the program and saves any changes made to the settings Clicking Cancel quits the program without saving any changes 4 DidapiConfig Planmeca DIDAPI Configuration Program Ethemet Interface PCI Interface Common System Info Image Preprocessing Pan Settings Dizi Settings ProSensor Settings
3. 8 Connect the sensor cable to the ControlBox and attach the sensor holder to the tube head support with doublesided tape ControlBox Bracket arm Velcro tapes and counterparts 1 2 Connecting the interconnection cable Planmeca Intra X ray Unit The interconnection cable is routed through the Planmeca Intra extension arm and out from the generator box single stud adapter ceiling arm or through the Planmeca Compact dental unit For more information see Planmeca Intra X ray unit installation manual publication number 10006030 40 Planmeca ProSensor Digital Radiography System User s Manual EMC INFORMATION APPENDIX B EMC INFORMATION A WARNING Use of any accessories and cables other than those specified in ProSensor Digital Radiography System documentation with exception of cables sold by Planmeca as replacement parts for internal components may result in increased emission or decreased immunity of the system WARNING ProSensor Digital Radiography System should not be used adjacent to or stacked with other equipment If adjacent or stacked use is necessary the ProSensor Digital Radiography System should be observed to verify normal operation in configuration which it will be used Guidance and manufacturer s declaration electromagnetic emissions ProSensor Digital Radiography System is intended for use in the electromagnetic environment specified below The customer or the user of the ProSe
4. 4 3 Resetting the IP Address NOTE The following procedure will reset the IP address Subnet Mask and the Default Gateway only 1 Switch on the power of the ControlBox 2 To access the reset button detach the bottom cover of the ControlBox by pushing the lock buttons on both sides of the ControlBox with your fingers 3 At the bottom of the ControlBox a small hole can be seen To reset the default IP address insert an appropriate tool into the hole pushing it to the bottom 4 The ControlBox indicator light starts to flash in yellow before switching to steady Next the steady green light comes on and switches to steady blue This will take a few seconds 5 Lift out the tool and reboot the ControlBox by unplugging and replugging the ControlBox cable 6 Open the DidapiConfig software see chapter 5 USING THE DIDAPI CONFIGURATION SOFTWARE on page 18 7 Click Open ProSensorEthernetConfig txt and enter the required information By clicking the Refresh button the modifications will be updated in the address fields User s Manual Planmeca ProSensor Digital Radiography System 17 USING THE DIDAPI CONFIGURATION SOFTWARE 5 USING THE DIDAPI CONFIGURATION SOFTWARE 21728888883 Planmeca a Didapi Configuration ZENworks For Desktops 4 b Acrobat Distiller 7 0 Adobe Acrobat 7 0 Professional The Didapi Configuration is used to configure and monitor Planmeca device drivers The DIDAPI Configurati
5. Auto Exposure Thresholds Values ProSensor 5 series 50 30 amp 51 30 E 52 50 0 4095 User s Manual Planmeca ProSensor Digital Radiography System 21 USING THE DIDAPI CONFIGURATION SOFTWARE 5 3 Configuring ProSensor ethernet interface NOTE The ProSensor Ethernet Interface can be configured in the Ethernet Interface tab Make sure that the configuration file path is defined as C Program Files Planmeca Dimaxis Program If not click Browse to select the correct path 4 DidapiConfig Planmeca DIDAP Configuration Program System Info Image Preprocessing Pan Settings Disi Settings ProSensor Settings Ethernet Interface PCI Interface Common Common Configuration File Path C Program Files PlanmecaNDimasisNProgram COMPUTERNAME Intra Ethernet Interface X Ray Sensor wepyk 3n002024 CLIENTNAME lt not available gt Planmeca ProSensor v IP Address 172 26 150 52 Network name unknown IP Port NOTE Current configuration shown by COMPLITERNAME wxpyk3n002024 Hox Bort pen sensor config file Pan Ceph Ethemet Interface X Ray Device Type No Pan or Pan Ceph device v IP Address Network name IP Port Rec pc IP Network name IP Port 1 3 NOTE Current configuration shown by COMPLITERNAME wxpyk3n002024 Box Port 77 Cancel To perform the configuration Enter the Con
6. PLANMECA ProSensor Digital Radiography System user s amp installation manual c 9 61001 TABLE OF CONTENTS 1 INTRODUCTION pc 1 Tal ae tee 1 1 2 Notes CAUTIONS warnings dio 1 1 3 Package contents for Ethernet USB interface 3 1 3 1 Ethernet interface Ur E TUS 3 1 3 2 USB Interfa e iier Ea eia EE AE 3 2 SYSTEM REQUIREMENTS nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn Gs 4 21 Planmeca Romexis computer requirements 4 PLANMECA PROSENSOR SYSTEM SETUP FOR ETHERNET amp USB INTER FA OE o reete ER REN eue EE cre DE ere TUE 5 3 1 Ethernet interface connection det arco pee Uer corp psu bua dup eR t aeneus 5 3 2 USB interface connection uoce id eene oer aedes ha fe itia Fes ra a iln dx Y 4 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM A c TE 8 4 DO COUfIOU allBrT cad carla cae b e e ode i fet dieti tritus fts 8 4 1 1 Disabling proxy See ems eae qu unie eet emp metu trenes imd 8 4 1 2 Changing the computer IP address 10 42 Planmeca ProSensor configuration utilities 13 4 2 1 Changing the ControlBox IP address 14 4 2 2 Updating the ControlBox softwa
7. Cables ControlBox to PoE PoE to LAN Power supply USB ControlBox Dimensions Cables Operating environment CMOS with scintillator overall 33 6 x 23 4 mm 1 33 x 0 92 in active area 25 5 x 18 9 mm 1 00 x 0 74 in number of pixels 850 x 629 view delay lt 5 sec overall 39 7 x 25 05 1 56 x 0 99 in active area 31 5 x 20 7 1 24 x 0 81 in number of pixels 1050 x 690 view delay lt 5 sec overall 44 1 x 30 4 mm 1 74 x 1 2 in active area 36 x 26 1 mm 1 74 x 1 2 in number of pixels 1200 x 870 view delay lt 5 sec 17 Ip mm 33 Ip mm 0 86 m 33 9 in or 2 0 m 78 7 in 112 x 46 x 24 mm 4 41 x 1 81 x 0 94 in 48 VDC 65 mA RJ45 10m OR 15m RJ45 10m OR 15m Phihong Single Port Injector Type PSA16U 480 POE Input voltage 100 240 VAC 50 60 Hz Output voltage 48VDC Max output current 0 35 A Insulation voltage Primary secondary 3000VDC 112 x 46 x 24 mm 4 41 x 1 81 x 0 94 in fixed USB 2 0 power supply cable 2 or 5m 6 6 or 16 4 ft Prior to installation of the system check that the local conditions are compatible with the appliance design The temperature of the operating environment should be between 15 C and 40 C The relative humidity of the operating environment should not exceed 60 Transportation and Storage Environment Transportation and storage temperature 5 C 60 C Relative humidity during transportation and storage should not exceed 60 38 Planmeca Pr
8. can be adjusted If the option Auto Levels Enabled is selected automatic adjustment is performed on the image when a new image is taken In the White high and Black 6 low fields percentage of the image tones to be cut in the ends of the histogram can be adjusted in order to gain reasonable contrast The Midtones value affects the gamma curve of the image By adjusting the gamma value you get an image that looks more like a conventional X ray image By enabling the FMH filter an image can be filtered and sharpened For Logarithmic Mapping adjustment tick the respective checkbox and select the appropriate parameter from the drop down menu The logarithmic S curves increases the contrast in the region of interest without clipping low or high values DICE Dental Imaging Contrast Enhancement is an image preprocessing method that suppresses low spatial frequencies in the image to bring out details in the image You can set DICE on or off separately for different image modalities by checking the respective check box If the settings have been changed the Apply button becomes active To save the changed values click Apply The recommended default settings can be restored by clicking the corresponding Set Defaults button Clicking OK quits the program and saves any changes made to the settings Clicking Cancel quits the program without saving the changes User s Manual Planmeca ProSensor Digital Radiography System 19 U
9. concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Electrical fast transient burst 2 kV for power supply lines Not Applicable Mains power quality should be that of a typical commercial or hospital environment IEC 61000 4 4 1 kV for input output 1 kV for input output lines lines Surge 1 kV line to line Not Applicable Mains power quality should be IEC 61000 4 5 2 kV line to earth Not Applicable that of a typical commercial or hospital environment Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 11 lt 5 96 Ur gt 95 dip in Ur for 0 5 cycle 40 96 Ur 60 dip in Ur for 5 cycles 70 96 Ur 30 dip in Ur for 25 cycles 5 96 Ur gt 95 dip in for5s Not Applicable Mains power quality should be that of a typical commercial or hospital environment If the user of ProSensor Digital Radiography System requires continued operation during power mains interruptions it is recommended that ProSensor Digital Radiography System be powered from an uninterruptible power supply Power frequency 50 60 Hz magnetic field IEC 61000 4 8 3 A m 3 A m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment The power frequency magnetic field should be measured i
10. no nicks in the cable The recommendable disinfectant solutions are Durr System Hygiene FD 322 or FD 333 or similar product The immersion time with the Durr disinfectants is 2 minutes If more effective disinfection or cold sterilization is preferred for cleaning recommend the Johnson amp Johnson Cidex Opa high level disinfectant at a minimum temperature of 20 C with maximum immersion time of 8 minutes for a reuse period not to exceed 14 days Follow carefully the manufacturer s recommendations on immersion time and recommended disinfectant liquids Do not leave the sensor in the disinfection solution overnight The magnetic connector of the sensor cable should not be soaked User s Manual Planmeca ProSensor Digital Radiography System 35 CLEANING Use a new disposable protection cap for every sensor usage Wipe up the sensor surface with a compress moisten into a sterile solution NOTE The sensor connector can be cleaned using a soft cloth 9 3 Sensor holders For cleaning the sensor holders refer to the manual supplied with the sensor holder package 9 4 Planmeca ProSensor ControlBox The ControlBox can be cleaned with a soft cloth damped in a mild cleaning solution CAUTION Switch off the unit before cleaning NOTE Do not disinfect the unit 36 Planmeca ProSensor Digital Radiography System User s Manual DISPOSAL OF THE PLANMECA PROSENSOR SYSTEM 10 DISPOSAL OF THE PLANMECA PROSENSOR SYS
11. operating instructions Planmeca pursues a policy of continual product development Although every effort is made to produce up to date product documentation this publication should not be regarded as an infallible guide to current specifications We reserve the right to make changes without prior notice COPYRIGHT PLANMECA 2009 06 Publication number 10019763 Version 2 2 Planmeca ProSensor Digital Radiography System User s amp Installation Manual INTRODUCTION INTRODUCTION This manual describes how to use and install the Planmeca ProSensor Digital Radiography System Please read this manual carefully before using and installing the system See also Planmeca Intra X ray unit user s manual NOTE The Planmeca Intra X ray unit and Romexis software have separate user s manuals which should be used in conjunction with this manual 1 1 Symbols Type BF equipment Standard IEC 878 The use of accessory equipment not complying with the N equivalent requirements of this equipment may lead to a reduced level of safety of the resulting system Consideration relating to the choice shall include use of the accessory in the Patient Vicinity evidence that the safety certification of the accessory has been performed in accordance to appropriate IEC60601 and or IEC60601 1 1 harmonized national standard TAL Planmeca ProSensor Digital Radiography System is c US supplied with the UL Recognition m
12. ready for the exposure and communicates with Romexis refer to section 7 1 Planmeca ProSensor ControlBox on page 25 On how to place the sensor into the patient s mouth refer to the sensor holder manual supplied with ProSensor User s Manual Planmeca ProSensor Digital Radiography System 31 USING THE PLANMECA PROSENSOR SYSTEM 7 3 Exposure values for Planmeca ProSensor sensors Select the digital imaging mode of the unit or adjust the exposure time according to the table NOTE In the digital imaging mode the highest time value that can be selected is 0 80 seconds Exposure values for ProSensor sensors with 20 cm 8 cones o o o o o o o o o o o o o o o o o TME 5 5 8 5 8 SIS EIF S 8 70 kV maxilla child mandible 66 kV maxilla child I P M mandible 63 kV maxilla child I P M mandible 60 kV maxilla child mandible 57 kV maxilla child I P M mandible 55 kV maxilla child I P M mandible 52 kV maxilla child mandible 50 kV maxilla child I P M mandible 70 kV maxilla adult mandible 66 kV maxilla adult mandible 63 kV maxilla adult 60 kV P M maxilla adult mandible 5
13. specified in the user s manual Select the exposure parameters according to the instructions specified in section 7 3 on page 32 It is recommended to use a sensor holder refer to the sensor holder manual supplied with the sensor holder package Select the correct sensor holder according to the exposure Intraoral images can be captured either as single images or into study templates containing a predefined set of multiple images To capture an intraoral image click the Intraoral Exposure button on the upper toolbar to initiate the intraoral image capture mode a The ntraoral Exposure window appears 26 Planmeca ProSensor Digital Radiography System User s Manual USING THE PLANMECA PROSENSOR SYSTEM 3 When the X ray unit is in ready state a message Waiting for Ready appears on top of the window Waiting for Ready Sensor 4 Prepare the patient for exposure select exposure parameters and position Planmeca Intra as required for more information refer to Planmeca Intra user s manual When the Planmeca ProSensor system is ready for exposure the message Waiting for Exposure appears on top of the window You can now expose the X ray as usual After the exposure a message stating Saving the image appears on the display and the image is automatically stored into the database 5 Define the tooth numbers and sensor orientation and take the next exposure or click Done to return to
14. up connec LAN settings Choose Settings above for dial up settings Appearance 4 The following window opens Disable proxy server by unchecking the Proxy server tickbox Click OK Local Area Network LAN Settings X Automatic configuration Automatic configuration may override manual settings To ensure the use of manual settings disable automatic configuration C Automatically detect settings Use automatic configuration script User s Manual Planmeca ProSensor Digital Radiography System 9 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 41 2 Changing the computer IP address The PC IP address must be changed to the same IP space with the Control box so that the ControlBox can be configured 1 Click on windows Start menu and select Control Panel Internet My Documents e Internet Explorer C My Recent Documents gt E mail 2 id s E Microsoft Office Outlook i vi 97 My Pictures Adobe FrameMaker 8 ex My Music Adobe Acrobat 7 0 4 My Computer Professional a My Network Places Acrobat Distiller 7 0 2 Control Panel EuroTranslator Set Program Access and Defaults Paint Printers and Faxes ah Notepad Help and Support 2 Search I Run All Programs D i Fujitsu Siemens Computers 10 Planmeca ProSensor Digital Radiography System User s Manual CONFIGURING PLANMEC
15. 7 kV maxilla adult mandible 55 kV maxilla adult mandible 52 kV maxilla adult mandible 50 kV maxilla adult mandible INCISORS P PREMOLARS AND CANINES M MOLARS 32 Planmeca ProSensor Digital Radiography System User s Manual USING THE PLANMECA PROSENSOR SYSTEM Exposure values for Planmeca ProSensor sensors with 30 cm 12 cones o o o o o o o o o o o o o o o o o me 2 8122212 4 84 8 44 4 3 48 e e e e e 70 kV maxilla child I P M mandible 66 kV maxilla child mandible 63 kV maxilla child I P M mandible 60 kV maxilla child I P M mandible 57 kV maxilla child PM mandible 55 kV maxilla child mandible 52 kV maxilla child mandible 50 kV maxilla child I PM mandible 70 kV maxilla adult 66 kV maxilla adult P M mandible 63 kV maxilla adult mandible 60 kV maxilla adult mandible 57 kV maxilla adult mandible 55 kV P M maxilla adult mandible 52 kV maxilla P M adult mandible 50 kV maxilla P M adult mandible P M INCISORS P PREMOLARS AND CANINES M MOLARS User s Manual P
16. A PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 2 The Control Panel window opens Click Network and Internet connections File Edit View Favorites Tools Help O P Ager gt Folders Em v A 5 Control Panel Switch to Classic View See Also Windows Update 77 Help and Support Other Control Panel Options Pick a category a Appearance and Themes Network and Internet Connections Add or Remove Programs 7 Sounds Speech and Audio Devices Performance and Maintenance Address a Printers and Other Hardware User Accounts Date Time Language and Regional Options Accessibility Options Security Center 3 In the Network Connections window right click the Local Area connection icon and select Properties File Edit View Favorites Tools Advanced Help Qes 00 Pare Brae Gg Address Network Connections LAN or High Speed Internet Network Tasks A Create a new connection Disable Set up a home or small 9 office network Status e Change windows Firewall settings i 2 Bridge Connections Disable this network ad device Create Shortcut Repair this connection Delete ta Rename this connection Rename View status of this connection Change settings of this connection Properties Other Places Control Panel My Network Places E My Documents My Computer Details Local Area Connection User s Manua
17. B or more 160 GB or more recommended Graphics card 128 minimum memory 128 minimum memory Monitor 1280 x 1024 1280 x 1024 Peripherals CD ROM drive CD ROM drive Backup medium None necessary DAT or equivalent Operating system Windows XP 2003 Vista Mac OS X Linux Mac OS Linux support subject to contract Windows XP Pro Windows 2003 Server Vista Other Java platform Java Virtual Machine 1 6 or later Java platform Java Virtual Machine 1 6 or later 4 Planmeca ProSensor Digital Radiography System User s Manual PLANMECA PROSENSOR SYSTEM SETUP FOR ETHERNET amp USB INTERFACE 3 PROSENSOR SYSTEM SETUP FOR ETHERNET amp USB INTERFACE 3 1 Ethernet interface connection The Planmeca ProSensor ControlBox must be installed so that the sensor can be easily placed in the the patient s mouth and that the input cable from the PoE Power over Ethernet port will reach the socket in the back of the PC NOTE The PoE port must comply with IEEE 802 3af standard NOTE Only equipment complying with IEC EN 60950 must be connected to the ethernet connector NOTE The ethernet cables must be connected to ethernet sockets only Do not connect the cables to any other equipment NOTE Ethernet connection has two LED indicator lights Green light signifies 100 baseTx link on and yellow Communication active NOTE The distance between PoE po
18. Digital Radiography System is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of ProSensor Digital Radiography System can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the ProSensor Digital Radiography System as recommended below according to the maximum output power of the Rated maximum output power of transmitter Separation distance according to frequency of transmitter m 80 MHz to 800 800 MHz to 2 5 W 150 kHz to 80 MHz MHz GHz d 1 2 P d 12 d 234p 0 01 0 2 0 2 03 0 1 0 4 0 4 07 1 1 2 1 2 24 ns 4 0 8 0 100 12 0 12 0 24 0 44 Planmeca ProSensor Digital Radiography System User s Manual Planmeca Oy Asentajankatu 6 00880 Helsinki Finland tel 358 20 7795 500 fax 358 20 7795 555 sales planmeca com www planmeca com PLANMECA Oys PLANMECA Environmental Quality System tom
19. Manual 5 PoE port with power cable 1 3 2 USB interface cu 6 5 4 gt S 9 1 Romexis Software package 2 Sensor holder package 3 ProSensor User s Installation Manual 4 Sensor hanger 6 Interconnection cable RJ45 7 Interconnection cable RJ45 8 ProSensor Ethernet ControlBox 9 ProSensor with cable 10 Sensor hanger 3 cs pw 7 Package conem USB 5 ProSensor USB ControlBox 6 Packing list 7 ProSensor with cable User s Manual Planmeca ProSensor Digital Radiography System 3 SYSTEM REQUIREMENTS 2 SYSTEM REQUIREMENTS NOTE NOTE NOTE NOTE The PC and other equipment connected to the system must be approved by local authorities e g IEC approved CE marked UL CSA approved located outside the patient area more than 2m 79 in from the X ray unit protectively earthed The connection of additional equipment to a multiple portable socket outlet must only be possible by using a tool or be supplied via separating transformer The multiple portable socket outlets shall not be placed on the floor Make sure that the system is protected with firewall and up to date anti virus software If possible isolate the system from office network 2 1 Planmeca Romexis computer requirements Processor Planmeca Romexis client work station 1 GHZ Planmeca Romexis database server 2 GHZ RAM 1 GB 2 GB minimum Hard disk space 40 G
20. SING THE DIDAPI CONFIGURATION SOFTWARE The preprocessing performed by DIDAPI is permanent and can not be undone by Romexis For more information on image preprosessing refer to Romexis Installation manual 4 DidapiConfig Planmeca DIDAPI Configuration Program Ethernet Interface PCI Interface Common System Info Image Preprocessing ProSensor Settings Auto Levels Enabled 7 FMH filter enabled White _ Dixi2 and Dixi3 Settings ito Le bled d Black oT Dimax2 and Dimax3 and SmartPan Panoramic Settings Es Use AGC v Logarithmic Mapping v DICE White Black Dimax2 and Dimax3 and SmartPan Bitewing Settings to Levels Enat White 000 Black 0 010 Dimax2 and Dimax3 Cephalostatic Settings C Soft Tissue Filter Enabled Soft Tissue Filter scale DIS ATIS EP SERA v Use AGC White 0010 0 100 Dixi Settings C Auto Levels Enabled white Dimax Panoramic Settings C Auto Levels Enabled Black z 0500 Pan Settings Logarithmic Mapping CI DICE Logarithmic Mapping CI DICE Logarithmic Mapping V DICE Disi Settings Log ProSensor Settings S Original B030 Midtones Set Defaults S Normal F3B034 Midtones Gamma Midtones Gamma 1 05 5 5 Normal SC Normal SC_B034 v Set Defaults Midtones
21. TEM In order to reduce the environmental load over the product s entire lifecycle PLANMECA s products are designed to be as safe as possible to manufacture use and dispose of Parts which can be recycled should always be taken to the appropriate processing centres after hazardous waste has been removed Disposal of obsolete systems is the responsibility of the waste possessor All parts and components containing hazardous materials must be disposed of in accordance with waste legislation and instructions issued by the environmental authorities The risks involved and the necessary precautions must be taken into account when handling waste products Waste Hazardous Main materials Recyclable waste Part disposal for disposal material separate site collection ControlBox metal stainless steel X plastic ASA PC X POM X PC X PU X Cables copper X TPE PU X Packing cardboard X paper X PE foam X Sensors Return the sensors to Planmeca Other parts PoE X NOTE If the component boards cannot be recycled handle them as electronic scrap i e according to the local legislation User s Manual Planmeca ProSensor Digital Radiography System 37 TECHNICAL SPECIFICATIONS 11 TECHNICAL SPECIFICATIONS Sensor Sensor type Sensor dimensions Size 0 Size 1 Size 2 Resolution Theoretical resolution Cable length Ethernet ControlBox Dimensions Power supply
22. ark 1 2 Notes cautions and warnings NOTE The system should be installed and operated by qualified personnel only NOTE EMC requirements have to be considered and the equipment must be installed and put into service according to the specific EMC information provided in the accompanying documents CAUTION Handle the Planmeca ProSensor Digital Radiography System according to the instructions given in this manual Do not pinch the sensor or the cable Do not to drop the sensor or pull strongly the sensor cable Never cut nick or sharply bend the sensor cable Always advise the patient not to bite the sensor or the cable The Planmeca limited warranty does not cover damage which is due to misuse e g dropping the sensor neglect or any cause other than ordinary application CAUTION Do not let the sensor cable run along the floor Protect the cable from rolling over it with a chair or walking over it User s Manual Planmeca ProSensor Digital Radiography System 1 INTRODUCTION CAUTION Do not store or use the Planmeca Sensor near 3m or 10 ft an electrosurgical knife AN WARNING Do not unnecessarily touch the connector pins to keep them clean 2 Planmeca ProSensor Digital Radiography System User s Manual INTRODUCTION 1 3 Package contents for Ethernet USB interface 1 3 1 Ethernet interface 1 Packing list 2 Sensor holder package 3 Romexis Software package 4 ProSensor User s Installation
23. e installed so that the sensor can be easily placed in the patient s mouth and that the cable of the USB hub will reach the socket in the back of the PC The USB cable must be connected to USB sockets only Do not connect the cables to any other equipment If the distance between the Control box and the PC exceeds 5 m a HUB must be used Connect the ControlBox USB cable to the PC Alternatively a hub can be connected between the PC and the ControlBox Connect the magnetic connector of the Planmeca ProSensor to the ControlBox Romexis sde qsn eAnxeiuox14y USB HUB User s Manual Planmeca ProSensor Digital Radiography System 7 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 4 4 1 4 1 1 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM PC configuration Disabling proxy server P Oy Wadan O P DUST pu PLANMECA The following example describes the configuration performed with the Internet Explorer 7 browser However configuration can be performed with any browser 1 To access the ProxyServer settings click Tools on your browser window Ju Eo ee ees Hali Bean Tools 2 Onthe appearing menu select Internet Options ge Safety Reopen Last Browsing Session 1 Pop up Blocker 43 Manage Add ons Cx Work Offline C
24. ensor Settings PCI Interface Common Log Log File workstation ID Log File C DOCUME 1 aaltole LOCALS 1 T emp Didapi log Log level Normal 7 Troubleshoot O Full Debug Intra Sensor used with this PC Intra Sensors Panoramic X Ray used with this PC Panoramic X Ray devices Save a Copy As Open DidapiConfig log DidapiConfig log As Default Location Alternative Location Browse Diril ISA Dixit PCI Dixi2 3 Dixi2 3 USB Dixi2 3 Ethemet ProSensor Proline EC CC with Dimax1 Proline EC CC with Dimax2 3 ProMax 1 16 PCI 1 17 gt PCI ProMax Ethernet Proline Ethernet Pro ne The Log level setting determines how much information will be written to the log file The Log level should be set to Normal If set to Full it might be hard to find relevant information for troubleshooting If intraoral images are taken with this PC check the option Intra Sensor used with this PC and select the ProSensor Ethernet intraoral sensor User s Manual Planmeca ProSensor Digital Radiography System 23 IMAGE QUALITY CONTROL 6 IMAGE QUALITY CONTROL Verify the image quality after installing the software and before patient exposure Perform quality control check according to the requirements of local authorities using for example Quart phantom or similar It is recommended to regularly monitor the image q
25. ensors 32 8 SENSOR HOLDERS i tisciipiitecepo E cC ec nnna 34 CLEANING t EN 35 S CSU ACCS 4196 eo ho Mec P ad Ed dut PE rre ues 35 92 Sensors and eablBS c de 35 9 3 Sensor holders ente est tant eth eae cate cates een d M D Ud 36 9 4 Planmeca ProSensor utra Ea de dudes 36 User s amp Installation Manual Planmeca ProSensor Digital Radiography System 1 TABLE OF CONTENTS 10 DISPOSAL OF THE PLANMECA PROSENSOR SYSTEM 37 11 TECHNICAL SPECIFICATIONS 38 APPENDIX A INSTALLING PLANMECA PROSENSOR SYSTEM TO PLANMECA INTRA X RAY UNIT eene een nnn 39 1 1 Installing the ControlBox to the bracket arm 39 1 2 Connecting the interconnection cable Planmeca Intra X ray Unit 40 APPENDIX B EMC INFORMATION enne nnn nnns 41 The manufacturer assembler and importer are responsible for the safety reliability and performance of the unit only if installation calibration modification and repairs are carried out by qualified author ized personnel electrical installations are carried out according to the appropriate requirements such as IEC364 equipment is used according to the
26. l Planmeca ProSensor Digital Radiography System 11 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 4 Scroll down the menu and select Internet Protocol TCP IP Click Properties Bx Local Area Connection Properties General Authentication Advanced Connect using ES ADMtek 4N983 10 100Mbps PCI Ad This connection uses the following items v File and Printer Sharing for Microsoft Networks v dE QoS Packet Scheduler 5 F Intemet Protocol v Ka TT 121 Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 5 Select Use the following IP address and change your computer IP settings to same IP space with the default ControlBox IP address 172 26 150 150 The address must not be identical with the ConrolBox IP address Click OK Internet Protocol T CP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 172 26 150 Sub
27. lanmeca ProSensor Digital Radiography System 33 SENSOR HOLDERS 8 SENSOR HOLDERS The sensor holders provide an easy way to position the sensor for different anatomical and diagnostic needs For instructions how to use the sensor holders please refer to the manual supplied with the sensor holder package 34 Planmeca ProSensor Digital Radiography System User s Manual CLEANING 9 CLEANING 9 Surfaces 9 2 Sensors and cables NOTE NOTE NOTE CAUTION NOTE Before cleaning the system always check that the X ray unit and the Planmeca ProSensor system are off Planmeca ProSensor ControlBox indicator light is off The surfaces can be cleaned with a soft cloth dampd in a mild cleaning solution Stronger cleaning agents can be used for disinfecting the surfaces We recommend D rr System hygiene FD 333 or respective disinfecting solution Planmeca ProSensor sensors allow enhanced infection control in the surgery As the sensor casing is hermetically sealed the sensors can be immersed in disinfectant solution Always use appropriate instruments for cleaning the sensors It is mandatory to carefully follow the disinfecting and cleaning recommendations in order to not damage the sensors The sensors cannot be sterilized autoclave or UV oven Wipe up the sensor surface with a soft cloth damped into a disinfectant solution The sensors can be soaked in a disinfection solution as long as there are
28. n the Command Prompt window via Windows Start menu by selecting All Programs gt Accessories gt Command Prompt 2 Type command ping and the new ControlBox IP address in the command prompt window Command Prompt 0 x Microsoft Windows Version 5 1 26001 Copyright 1985 2001 Microsoft Corp User s Manual Planmeca ProSensor Digital Radiography System 15 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 42 2 Updating the ControlBox software 1 Select Upload ControlBox SW Planmeca Prosensor Mozilla Firefox pedosto e 2c J hteif122 26 190 9 0idex her ep PLANMECA PLANMECA intraoral sensor Excellence in dentistry Utilities e Change IP address e Upload Control Box SW di 2 Browser goes to http 172 26 150 150 upload asp To select a new software version click Browse and Send gt http 172 26 150 150 upload asp Windows Internet Explorer G yv http 172 26 150 150 upload asp we amp f hitpilf172 26 180 150 uplosd asp n x i T 2 E mee Upload Control Box SW Select file C Browse 3 Wait until the ControlBox indicator light goes from yellow to blue and reboot the ControlBox 16 Planmeca ProSensor Digital Radiography System User s Manual CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM
29. n the intended installation location to assure that it is sufficiently low NOTE Ur is the a c mains voltage prior to application of the test level 42 Planmeca ProSensor Digital Radiography System User s Manual EMC INFORMATION Guidance and manufacturer s declaration electromagnetic immunity ProSensor Digital Radiography System is intended for use in the electromagnetic environment specified below The customer or the user of ProSensor Digital Radiography System should assure that it is used in such an environment IEC 60601 Compliance Electromagnetic environment Immunity test test level level guidance Portable and mobile RF communications equipment should be used no closer to any part of the ProSensor Digital Radiography System including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance Conducted RF 3 Vrms 3 Vrms IEC 61000 4 6 150 kHz to 80 MHz 12 d 1 2 P 80 MHz to 800 MHz Radiated RF 3 V m 3 V m IEC 61000 4 3 80 MHz to 2 5 GHz M where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in metres m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each freque
30. ncy range Interference may occur in the vicinity of equipment marked with the following symbol NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which ProSensor Digital Radiography System is used exceeds the applicable RF compliance level above ProSensor Digital Radiography System should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating ProSensor Digital Radiography System Over the frequency range 150 kHz 80 MHz field strengths should be less than 3 V m User s Manual Planmeca ProSensor Digital Radiography System 43 EMC INFORMATION Recommended separation distances between portable and mobile RF communications equipment and ProSensor Digital Radiography System communications equipment ProSensor
31. net mask 255 255 0 0 Default gateway 172 26 0 1 Ibtain DNS server ad mat Use the following DNS server addresses Preferred DNS server Alternate DNS server 12 Planmeca ProSensor Digital Radiography System User s Manual CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 4 2 Planmeca ProSensor configuration utilities On the Planmeca ProSensor main page you will find utilities for Changing the Planmeca ProSensor IP adress Updating the ControlBox software To access the Planmeca ProSensor main page Type the IP address of the controlbox and index html in the address field of the browser eg http 172 26 150 150 index html If the address has been modified it might be different from the adress of this example Make sure to type in the latest configured address of the control box The following window opens Planmeca Prosensor Mozilla Firefox pedoto Sruhitoria Krjanmerik Tyka PLANMECA intraoral sensor Utilities Change IP address Upload Control Box SYY Qr c x o Gema ProSensor Excellence in dentistry User s Manual Planmeca ProSensor Digital Radiography System 13 CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 4 2 4 Changing the ControlBox IP address 1 Click the link Change IP address Planmeca Prosensor Mo
32. nsor Digital Radiography System should assure that it is used in such an environment CISPR 11 Emissions test Compliance Electromagnetic environment guidance RF emissions ProSensor Digital Radiography System uses RF Group 1 energy only for its internal function Therefore its emissions are very low and are not likely to CISPR 11 cause any interference in nearby electronic equipment RF emissions ProSensor Digital Radiography System is Class B suitable for use in all establishments including domestic establishments and those directly connected to the public low voltage power supply Harmonic emissions IEC 61000 3 2 Not Applicable network that supplies buildings used for domestic purposes Voltage fluctuations flicker emissions IEC 61000 3 3 Not Applicable User s Manual Planmeca ProSensor Digital Radiography System 41 EMC INFORMATION Guidance and manufacturer s declaration electromagnetic immunity ProSensor Digital Radiography System is intended for use in the electromagnetic environment specified below The customer or the user of ProSensor Digital Radiography System should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge ESD IEC 61000 4 2 6 kV contact 8 KV air 6 kV contact 8 KV air Floors should be wood
33. oSensor Digital Radiography System User s Manual INSTALLING PLANMECA PROSENSOR SYSTEM PLANMECA INTRA X RAY UNIT APPENDIX A INSTALLING PLANMECA PROSENSOR SYSTEM TO PLANMECA INTRA X RAY UNIT 1 1 Installing the ControlBox to the bracket arm NOTE These instructions apply for Ethernet installation The ProSensor interconnection cable is routed into the Planmeca Intra bracket arm at the factory 1 Remove the cable opening plug on the bracket arm Plug Opening for the interconnection cable ProSensor interconnection cable Bracket arm 2 Pull out the interconnection cable for approx 19 cm 7 5 in as shown in the figure below 3 To ensure that the interconnection cable moves freely as the bracket arm moves route the cable through the bracket arm as shown in the following figure 4 Cut the plug and attach it to the cable Reattach the plug to the bracket arm opening User s Manual Planmeca ProSensor Digital Radiography System 39 INSTALLING PLANMECA PROSENSOR SYSTEM PLANMECA INTRA X RAY UNIT NOTE The plug is cut on the rounded end Remove the cap from the opening before assembling the plug to the cable 5 Attach the velcro tapes under the ControlBox 6 Clean the bracket arm properly with pure alcohol 7 Connect the interconnection cable and attach the ControlBox to the arm Plug Interconnection cable B N Opening 19cm ControlBox
34. ompatibility View Settings A Full Screen F11 Toolbars Explorer Bars k gt Developer Tools F12 Suggested Sites Windows Messenger Diagnose Connection Problems 7 Internet Options 8 Planmeca ProSensor Digital Radiography System User s Manual CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 3 On the Connections tab click Lan Settings Internet Options Z3 Internet Options y General Security Privacy Connections Programs Advanced General Security Privacy Content Connections Programs Advanced Home page 5 To set up an Internet connection click d To create home page tabs type each address on its own line Setup 1 http fintranet Dial up and Virtual Private Network settings Remove Browsing c T Delete temporary files history cookies saved passwords Settings and web Form information C Delete browsing history on exit Choose Settings if you need to configure a proxy server for connection Settings Never del poonectior Search Dial whenever a network connection is not present Change search defaults Settings Always dial my default connection Current None Set default Tabs Change how webpages are displayed in Settings Local Area Network LAN settings NURSE SEDE tabs LAN Settings do not apply to dial
35. on software is automatically installed with the Romexis software Open the DIDAPI Configuration software by clicking Start gt Programs gt Planmeca gt Didapi Configuration Planmed I Acquire MG 2 2 3 b DIDAPI Readme Ext QuickTime b Dimax3Tool SiS VGA Utilities Install Romexis License Startup ProMax3D Tool WSOY Romexis Romexis Configuration Romexis Service Control CEEEEEPFJS Beam Check 2 The DIDAPI Configuration tool will start and the System Info window appears 4 DidapiConfig Planmeca DIDAPI Configuration Program Ethernet Interface perating System Processor System Uptime Physical Memory RAM Windows Directory System Directory Temp Directory Computer Name Client Name User Name Create Report Microsoft Windows XP Professional Version 5 1 Build 2600 Service Pack 3 x85 Family 15 Model 4 Stepping 3 3066 MHz 1 Processor s System 00 58 43 20GB available 1 1 GB CAWINDOWS available 46 99 GB CNWIND WS system32 available 46 99 GB CADOCUME 1 aaltole LOCALS 1 Temp available 46 99 GB WX lt PYBNN184568 lt not available gt aaltole PCI Interface Common Log System Info Image Preprocessing Pan Settings Dixi Settings ProSensor Settings 18 Planmeca ProSensor Digital Radiography System User s Manual USING THE DIDAPI CONFIGURATION SOFTWARE 5 1 Image Preprocessing In this tab the parametres for intraoral images
36. re 16 4 3 Resetting the IP Address 4 os aeo 17 5 USING THE DIDAPI CONFIGURATION SOFTWARE 18 5 1 Image Preprocessing ota meter rte pe e eee pecu tu det os Eua aiie 19 5 2 Configuring Planmeca ProSensor settings 21 5 2 1 Auto exposure threshold values Ethernet interface 21 5 3 Configuring ProSensor ethernet interface 22 GC MEE CT n PET 23 6 IMAGE QUALITY CONTHRODL 2 222duxe ree rure ceu carece es ccu cente oin onn 24 6 1 Quality cheek using SMPTE test pattern i e oe eet eb apes ips 24 7 USING THE PLANMECA PROSENSOR SYSTEM 25 7 1 Planmeca ProSensor ControlBox eese 25 7 1 1 Planmeca ProSensor ControlBox indicator light 25 7 2 Image acquisition Planmeca Intra X ray unit with Romexis 26 7 2 1 Preparing an intraoral exposure 26 7 2 2 Capturing Intraoral Images 26 T2 S Patient positioning sss oret rate onto 31 7 2 4 Positioning the Sensor ete oreet tabu 31 7 3 Exposure values for Planmeca ProSensor s
37. rolbox indicator light is dim blue intraoral exposure mode and the cable is connected to the ControlBox Planmeca ProSensor system is on Imaging controlbox indicator light is bright blue program communicates with the Planmeca ProSensor system Waiting for Ready controlbox indicator light is blue and flashing slowly Waiting for Exposure controlbox indicator light is green and steady The exposure is taken and image is controlbox indicator light is green and flashing transferred from the sensor to the ControlBox rapidly Error mode controlbox indicator light is red and steady Service mode controlbox indicator light is yellow and flashing Uploading ControlBox software slowly NOTE The exposure can only be taken when the indicator light on the Planmeca ProSensor ControlBox is green and steady not when the indicator light is flashing User s Manual Planmeca ProSensor Digital Radiography System 25 USING THE PLANMECA PROSENSOR SYSTEM 7 2 Image acquisition Planmeca Intra X ray unit with Romexis 7 2 1 Preparing an intraoral exposure NOTE 7 2 2 Capturing Intraoral Images Single images 2 Detailed instructions for using Planmeca Intra X ray unit and Romexis software are given in their user s manual which should be used in conjunction with this manual Select the desired CMOS sensor and connect it to the Planmeca ProSensor ControlBox Prepare and position the X ray unit as
38. rt and ControlBox must not exceed 100 m 1 Connect the Ethernet cable from the PC LAN network to the input socket of the PoE port If necessary a hub can be connected between the PC and the PoE port 2 Connect the Ethernet cable from the PoE output socket to the ControlBox 3 Connect the ProSensor cable to the ControlBox The PoE port can be installed in the same space with the Hub Ethernet switch or next to the ControlBox The control box must be installed so that no liquid will spill on it Typical network configuration 1 ProSensor ll Romexis Control box i Max 100m Ethernet Max 100m HUB or Ethernet switch 100 240VAC User s Manual Planmeca ProSensor Digital Radiography System 5 PLANMECA PROSENSOR SYSTEM SETUP FOR ETHERNET amp USB INTERFACE Typical standalone configuration ProSensor fi Romexis sde zeAnxeiuex y Control box Max 100m Ethernet Max 100m 100 240VAC Connecting Planmeca ProSensor ControlBox to PoE Power over Ethernet port ProSensor with cable ProSensor ControlBox 6 Planmeca ProSensor Digital Radiography System User s Manual PLANMECA PROSENSOR SYSTEM SETUP FOR ETHERNET amp USB INTERFACE 3 2 USB interface connection NOTE NOTE Alternative connection max 5m Fixed 2 or 5m The Planmeca ProSensor ControlBox must b
39. the maging module when all exposures have been captured User s Manual Planmeca ProSensor Digital Radiography System 27 USING THE PLANMECA PROSENSOR SYSTEM Template images To capture intraoral images into a study template click this button 1 Select the desired study template from the list At the beginning of the list there are empty templates and at the bottom of the list there are studies with dates that already include images captured earlier Select Study FMX 18 FMx 20 10 5 2006 FMx 18 24 26 36 34 26 28 38 36 28 Planmeca ProSensor Digital Radiography System User s Manual USING THE PLANMECA PROSENSOR SYSTEM While capturing images using a study Romexis navigates through the template in a predefined order denoting the current image to be captured by a blue border around the slot 2 Follow the tooth numbering and sensor orientation as shown on the image and predefined in the template User s Manual Planmeca ProSensor Digital Radiography System 29 USING THE PLANMECA PROSENSOR SYSTEM To cancel the process click the Cancel button The captured images are saved and the incomplete study is preserved for later use 3 L nra nra 1312 11 21 8 L irera hta nta 24 26 36 34 26 79 38 36 18 16 4648 1614 4446 10 4243 Sensor Onentabon FERES E m iin In e n s js ma Sg a
40. trolBox IP Address in the correct field and click Apply The default IP adress is 172 26 150 150 see also paragraphs 4 2 1 Changing the ControlBox IP address on page 14 and 4 3 Resetting the IP Address on page 17 Alternatively you can leave the P Adaress field empty and enter the network name in the Network name field It is not necessary to enter the IP address as well as the network name by entering the IP address you will obtain the network name and vice versa All IP addresses do not necessarily have a network name When using Planmeca ProSensor in the same PC with Dixi PCI or USB interface imaging is performed with the Dixi sensor even though the Planmeca ProSensor has been configured Choosing Dixi Ethernet will affect imaging only if Dixi Ethernet interface is being used 22 Planmeca ProSensor Digital Radiography System User s Manual USING THE DIDAPI CONFIGURATION SOFTWARE 5 4 Log NOTE From the Log window the Didapi Log can be accessed and a copy of the log can be saved to the desired location Log File Workstation ID sets the name of the current workstation s DIDAPI log file Check that the log file path has been defined The log file location can be changed from Alternative Location Browser Default Location restores the default log file path 4 DidapiConfig Planmeca DIDAPI Configuration Program System Info Image Preprocessing Ethernet Interface Pan Settings Disi Settings ProS
41. uality using the same phantom according to the requirements of local authorities Before performing phantom exposures verify that the brigthness and contrast settings of the monitor are accurate by using a SMPTE test pattern or similar 6 1 Quality check using SMPTE test pattern The test image is specified by the Society of Motion Picture and Television Engineers www smpte org and follows the SMPTE Recommended Practise RP 133 1991 Specifications for Medical Diagnostic Imaging Test Pattern for Television Monitors and Hard Copy Recording Cameras This image should be used for monitor setting and quality checks performed Before every working day The 5 gray field inside the 0 field and the 95 gray field inside the 100 field should be visible If not adjust the brightness and contrast of the monitor Every month The line raster in the corners and in the center must be visible the vertical and horizontal lines must form undistorted squares and the homogenous gray background must not be coloured 24 Planmeca ProSensor Digital Radiography System User s Manual USING THE PLANMECA PROSENSOR SYSTEM 7 USING THE PLANMECA PROSENSOR SYSTEM 7 1 Planmeca ProSensor ControlBox ProSensor indicator light 7 1 1 Planmeca ProSensor ControlBox indicator light PLANMECA PROSENSOR STATUS Planmeca ProSensor system power off controlbox indicator light is off Planmeca ProSensor system is off not in cont
42. zilla Firefox pedo Sruhitoria Krjanmerikt Ty kat we Bo 13 hitpsj 172 26 150 5 ndex html PLANMECA intraoral sensor PLANMECA ProSensor Excellence in dentistry Utilities e Change IP address 4 load Control Box SW 2 Mozilla Firefox pedoto Mud aa m e c A http f 122 26 150 150 netefgasp Control Box IP address Configuration TCP IP TP Address 17226150150 Subnet Mask 25525500 Default Gateway 172 26 0 1 MAC Address 00 09 21 00 3E 7C send Browser goes to http 172 26 150 150 netcfg asp and the following window opens The default IP address for each ControlBox is 172 26 150 150 To change the ControlBox IP address type the new IP address Subnet Mask and Default Gateway in the corresponding fields and click Send Wait until the ControlBox indicator light switches from yellow to blue Reboot the ControlBox by unpluging and repluging the ControlBox cable Change the computer IP address back to original for more information see section Changing the computer IP address on page 10 14 Planmeca ProSensor Digital Radiography System User s Manual CONFIGURING PLANMECA PROSENSOR DIGITAL RADIOGRAPHY SYSTEM 7 Change the new Controlbox IP to DidapiConfiguration please see section Configuring Planmeca ProSensor settings on page 21 To test the ControlBox connection 1 Ope
Download Pdf Manuals
Related Search