DIGIgarde PLUS Reader Installation Instructions
Contents
1. ACCESS EVERYWHERE CAUTION Ensure that the supplied ferrite ring is DIG lga rde PLUS Wiring fitted to the units cable bundle for EMC protection ais incor ss mtn Black aa T T WDO IN Wiegand Input Data 0 WD1 IN Wiegand Input Data 1 WDO0 OUT Wiegand Output Data 0 White WD1 OUT Wiegand Output Data 1 weour White O gand Outp Introduction DIGlgarde PLUS is a combined fingerprint and smart card reader with integral backlit keypad providing User ID fingerprint PIN and smart card authentication modes This Quick Start Guide explains how to Unpack the unit and prepare for installation Mount the unit using the supplied fixing kit Connect the unit Set up an administration account Enrol a user and record their fingerprint Verify a user and scan a fingerprint Please read the user manual on the accompanying CD for detailed information about any of these steps Black GND Wiegand GND gt e We o o Lock The user manual can also be downloaded from the TDSi website http www tdsi co uk For technical assistance contact TDSi Support on 44 0 1202 724998 or email support tdsi co uk C E epesstuton C mo i nomaycosa Nam pe ALARM NO2 DiGlgarde PLUS 9002 0455 Al N lly O Quick Start Guide arm Normally Open Alarm Common sam e ALARM COM2 RS 485A 2 RX RS 485 2 level RS485 2 RS 485B 2 RX RS 485 2 level E RS 232 OV RS 232 OV Grey RS 232 RX Receive Data RS 232C level2. RS 232 TX Transmit Data RS 232C level RS 485A 1 RX RS 485 1 level QS015 Issue 1 Copyright 2012 TDSi 1 Unpacking This pack contains 2 Mounting Unfasten and remove the screw on the base of the DIGlgarde PLUS Remove the back cover Use the mounting template to mark out the drill holes and cable access point Drill the two 6mm holes to a depth of 35mm Push the supplied plugs into the drill holes A TDSi DIGlgarde PLUS fingerprint reader CD with operating software and manual Mounting template Cable assembly RS 485B 1 RX RS 485 1 level Ferrite ring Tool for security screw Fixing kit Suppression diode Fasten the unit s back plate to the wall using the supplied screws Ensure that the anti tamper magnet is positioned correctly Feed the cable into the wall and hook the top of the RS485RES Brown Brown RS 485RES Link wires to provide termination RS 485RES resistor for this unit see below DIGlgarde PLUS onto the mount Fit the supplied ferrite ring around the wire bundle for EMC Cabling Requirements protection You will need to supply and install the following cables RS232 TX purple to the unit l C ery 3 Connections RS232 OV black DIGlgarde PLUS can be connected to other devices access control units lock door sensor alarm host PC etc through the colour coded and labelled connection cables In addition to the connections described in the table opposite there is
3. also a pre configured POl capable RJ 45 connector RS232 RX grey RS232 RS485 Communications y Communications RS232 or RS485 Screened cable Belden 9729 Belden 9502 OS2P24 OS2P22 Alpha 5902 Alpha 5094 or other equivalent screened alarm cable Communications TCP IP Cat5 or Cat6 RS485 1 blue RS485 1 yellow Access Controller Power Supply 6 core Belden 9730 Belden 9503 Alpha 5096 or OS6C24 CAUTION Lock strike suppression devices MUST be fitted directly across all inductive loads such as lock RS232 port RS232 RS485 rn strikes secondary relays and automatic door openers converter Failure to adhere to this notice will invalidate the warranty of this product and may result in irreparable damage to it and other connected equipment On first unit short On last unit short two brown wires two brown wires in RS485REM in RS485REM bundle if converter bundle to provide does not provide termination resistor termination resistor 4 Standalone Use a Enrolment Menu To enrol a user press the Menu button If you have registered an Administrator Manager or Enroller account d User Manage you are prompted to verify your identity see Step c After you have Options done this press the Menu button again Sys Info Press the OK button to select the User Manage menu option Select Enrol User and follow the on screen prompts to User Manage Enrol User 1 Select a user ID 2 Choose the enr
4. olment method fingerprint FP password Pwd or both FP amp Pwd 3 Scan a finger three times and or enter a 5 digit password or PIN 4 Repeat the procedure to provide the user with a backup fingerprint 5 Save the template FP Card Mng Enrol dmin Enrol User Enrol FP Enrol Pwd FP amp Pwd b Setting up Admin Accounts The first time the DIGlgarde PLUS is powered up there are no user accounts Your first step should be to create one or more protected administrator accounts DIGlgarde PLUS recognises three admin levels Enroller Manager Menu y Admin User Manage To set up an Admin Manager or Enroller account Options Sys Info 1 Press the Menu button 2 Press the OK button to select the User Manage menu option 3 Inthe User Manage menu use the A V keys to select the Enrol Admin option 4 Usethe AVY keys to select the enrolment method fingerprint FP password PWD or both FP amp Pwd Press the OK button 5 The Admin Accredit screen is displayed Use the A V keys to choose the management role 6 Follow the on screen prompts to scan a finger three times and or enter a password c Verification The verification process involves one or more of the following steps Keying in your user ID Scanning the fingerprint recorded during enrolment Entering your password Reading of a smart card N N NW N 5 Connecting to an ACU a Connections WG OUT TCP IP Netw
5. ork required for template distribution b Configure Reader Format Choose whether you want to use Wiegand format or Magnetic Clock and Data Format 1 Press the Menu button 2 Use the VW to select Options and press the OK button 3 Press the V key to select 4 Use the AV keys to select Data Out Type and then either WG Type Wiegand or press the OK button MAG Type Magnetic mode Menu User Manage Options Log Opt Data Out Type Options Sys Info LED Mode Data Out Type c Configure Wiegand Mode If you are using Wiegand mode you will need to set up the Wiegand data format 1 Press the Menu button 3 Press the OK button to 4 Use the VW key to select 2 Press the V key to select select System Opt Wiegand and press the OK Options and press the OK button button Menu Options System Opt User Manage gt System Opt DLST Options Power Mng Wiesand Sys Info Comm Opt Adn Options 5 Use the WV key to select 6 Select Output Format and 7 Usethe AVY keys to select Output Setting and press the OK button the required format for press the OK button Wiegand Input Setting example WG26 without ID Output Setting Output Format Output Setting gt Output Format gt Output Setting Output User Site Code 256 G26 without ID ESC OK
Download Pdf Manuals
Related Search