Home

PROTEUS

1. channel Value Function CH1 0 No Strobe Effect 1 255 Strobe Speed from slow to fast ere 0 255 Red Dimmer 0 100 H ere 0 255 Green Dimmer 0 100 ii 0 255 Blue Dimmer 0 100 Cre 0 255 White Dimmer 0 100 0 127 Motor Position CH6 128 191 Clockwise rotation speed from fast to slow 192 255 Counterclockwise rotation speed from fast to slow CH7 0 255 Automatic Programs Stagg IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS HEED ALL WARNINGS If after you have followed the instructions outlined above this device fails to function please contact your dealer Under no circumstances should this device be opened Leave all servicing to qualified personnel Electrical appliances must never be used in conditions of high humidity or heat To prevent any risk of fire or electric shock never spill or splash liquids on this device Should this happen unplug the power cable from the mains outlet and switch off the mixer immediately MARKING amp CONFORMITY 1 The CE mark on this product means it conforms to the EMC Directive 2004 108 CE CE marking Directive 93 68 EEC and Low Voltage Directive 2006 95 EC 2 The Crossed out Wheeled Bin is to draw your attention to the WEEE Waste Electric amp Electronic Equipment Directive 2002 96 EC It means this apparatus must be collected separately for recycling 3 ROHS compliant means this device conforms to the Directive 200
2. 2 95EC on the restriction of the use of certain hazardous substances in electrical and electronic equipments such as Mercury Lead Cadmium Hexavalent Chromium Polybrominated Buphenyl PBB and Polybrominated Diphenyl Ethers PBDE 13 11 13 DISTRIBUTOR DEALER X wows CE
3. User Manual PROTEUS SDJ PROTEUS Table of Contents 1 BEFORE USAGE This package contains Unpacking Introduction Specifications Features 2 INSTALLATION Installation Requirements Maintenance Power Connection DMX 512 Connection 3 OPERATION Menu Map Operating Instructions DMX 512 Control DMX Channels 1 BEFORE USE This package contains e 1x Proteus e 1x Power Cable e 1x User Manual Unpacking e Thank you for purchasing this product it has been thoroughly tested and has been shipped in perfect operating condition e Carefully check the packaging for damage that may have occurred during shipping e Ifthe packaging appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact e f damage has been found or parts are missing please contact your vendor or our customer support number for further instructions Introduction e This fixture can operate in four different operating modes DMX control sound active automatic programs or in a Master Slave configuration e This product comes with several built in programs that can be used while operating as a single unit or with multiple units linked in a master slave configuration e For best results use fog or special effects smoke to enhance the beam projection e Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture e Warnin
4. e menu list or reduces the value when in a function AFTER CHANGING ANY VALUE IN THE LIGHT WAIT UNTIL THE DISPLAY TURNS OFF AT THIS POINT THE CHANGES WILL BE SAVED INTO THE MEMORY AND WILL BE REMEMBERED WHEN POWER IS TURNED OFF AND BACK ON DMX Address Setup e Press MENU until A001 to A512 is displayed e Change the DMX address by pressing UP or DOWN e Press ENTER to save the DMX address Automatic Program Setup e Press MENU until AX X is displayed e Choose your program of preference see menu map by pressing MENU repeatedly e Adjust the speed of the program by pressing UP or DOWN Sound Control Setup e Press MENU until SX X is displayed e Choose your program of preference see menu map by pressing MENU repeatedly e Adjust the speed of the program by pressing UP or DOWN Master Slave Setup e Set the Master Light to your automatic program or sound control program of choice e Set all Slave Lights to DMX Address 001 and daisy chain them to the DMX out of the Master Light DMX 512 Control This function allows you to use a universal DMX 512 controller such as the Stagg COMMANDOR 10 to control the PROTEUS a DMX controller allows you to create unique programs tailored to your individual needs The PROTEUS uses 7 DMX channels this will allow you to create custom lightshows Follow the instruction on the following DMX address charts DMX Channels 7 Channel Mode 7 Channels Table
5. g This product may cause severe eye damage Avoid looking directly into the light source at all times Specifications e Light source 20W RGBW LED e Strobe 0 20HZ Input Voltage AC100V 240V 50 60HZ e Max Power Consumption 25W e Packing Dimensions 370x220x280mm e Net Weight 2 00 kg e Gross weight 2 68 kg Features e 3PIN XLR DMX in and out e IEC Power Input e 4control modes DMX512 automatic programs sound control mast slave Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 2 INSTALLATION Installation requirements e The product can be hung or placed on a solid surface with the double mounting brackets e If you install the light in a hanging position always use a suitable mounting position and a clamp or screw that is strong enough to hold the product without stress Always use a safety wire to secure the light e Always keep a distance of minimum 0 5m to all objects or persons e Installation should always be done by a trained professional e Make sure the light always has good ventilation e Itis recommended to always use 110 Ohm DMX cable to prevent data corruption of your DMX control signal Maintenance This product shoud be freed regularly from dust other deposits and contamination Before cleaning always disconnect the product from the mains Maintenance should be performed on a regular basis e Always make
6. sure the product has completely cooled down e Check all screws they should be properly tightened and free from any corrosion e The housing lenses mounting supports and the installation location should not be deformed modified or tampered with e Mechanically moving parts must not show signs of wear amp tear or blockage or rubbing e Any cables should not show any form of damage or wear e Clean the outside lens with glass cleaner and a soft cloth dry carefully after cleaning e Clean the outside of the product with a damp soft cloth Only use water without any detergents Never immerse the device in any liquid Dry carefully after cleaning e Remove dust from the inside by blowing compressed air through the ventilation holes to expel Power connection The equipment has an auto switching power supply that can accommodate a wide range of input voltages The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages This equipment will accommodate between 100V and 240v AC 50 60HZ Color Connection PIN Brown AC live wire 1 Blue AC zero curve 2 Green Yellow AC ground wire 3 DMX 512 Connection 1 Connect the male 3pin DMX input of the first fixture to the female 3pin DMX output of the lighting controller using 110 Ohm DMX cable for example a Stagg Commandor 10 skip this step when not using a controller 2 Connect
7. the output of the first fixture to the input of the next fixture using 110 Ohm DMX cable Repeat this process until you reach your last fixture Here it is recommended to connect a DMX terminator to the output of the last fixture in the chain Always use proper 1100hm DMX cable such as the Stagg NDX series Using regular 600 Ohm microphone cable can cause data corruption and unwanted or bizarre response from your lights It is also recommended to place a DMX terminator on the last light in your DMX chain such as the Stagg NDXTERMINR 3 2 DMX DMX IN Gef DMX OUT Menu Map Operating Instructions A001 A512 DMX Adress AXX A1 X m Red Automatic Program A2X m Green Automatic Program A3 X m Blue Automatic Program A4 X m gt White Automatic Program A5 X RGBW Automatic Program A6 X Seven Colors Automatic Program A7 X m gt Rainbow all colors gradually A8 X Strobing Automatic Program S1 X HM Sound Controlled Strobing S2X Sound Controlled Color Change Button Function MENU ESC Exits from the current menu or function ENTER Enters the currently displayed menu or confirms the currently selected value UP Navigates upwards through the menu list or increases the value when in a function DOWN Navigates downwards through th

PROTEUS

Contents

Download Pdf Manuals

Related Search

Related Contents