Composer/ComposerPlus
Contents
1. Optical Disc Duplicator s Manual Notices The information in this document is subject to change without notice NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without prior written consent Trademark Acknowledgments Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Printing History Edition 2 2 090402 FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Users in the United States This product is intended to be supplied by a UL Listed Direct Plug In Power Supply marked Class 2 or a UL Listed ITE Power Supply marked LPS with output rated 24 V dc 2 5 A This equipment has been tested and found to comply with the limits for a C2. lt a TOC INDEX Check one more time for printer alignment after the screws have been tightened down just in case something changed while you were making the adjustment Re align if necessary l Press the Sequence button m Press the Pick button The CD will drop into the Output Bin n Press the Pick button again The CD will be picked up out of the Output Bin o Press the Sequence button several times until the CD is transported back above the Input Bin p Press the Pick button The CD will drop into the Input Bin C FINE TUNING THE PRINTER STAND ALIGNMENT If you find that some discs are not being held tightly in the printer tray and start to move inside the printer while printing the printer stand may need further alignment If the discs are not placed in the exact center of the Printer Tray it is possible you will encounter failed picks or poor print quality There is a special Fine Tune Alignment built in to the program of the Duplicator to ensure proper picks To perform this alignment follow these steps 1 Open the Printer Tray by pressing the Printer Tray Button on the top of the Printer Control Panel 2 Loosen the three Printer Stand Adjustement Screws shown Press the Sequence Button on the front of the Duplicator until the Robotic Arm is positioned over the Input Bin 3 Press and hold the Pick Button on the Duplicator s Front Control Panel for 5 seconds Your will see the LEDs on the front of the D
3. 6 After recording the CD Tray opens automatically so that the Robotic Arm can pick the CD and transport it to the optional printer Print time varies according to which printer has been selected Both ink jet and thermal printers are available In most cases print time takes no more than 1 minute 4 Getting Started gt TOC INDEX 7 After printing the printer s CD Tray opens automatically and the Robotic Arm picks the CD and transports it to the Output Bin The process starts over and repeats until all blank discs are gone or the number you have specified via software are copied and printed Here is a schematic of the process Start Start Again Start Again gt lt Input Bin CD R Recorder Good Output Bin Now that you understand the principle and the order of operation it is time to set up your Duplicator This is discussed in the next several sections Nor Good Reject Area Getting Started 5 lt a TOC INDEX B CHOOSING A GOOD LOCATION Place the Duplicator in a location with adequate air circulation to prevent internal heat build up If you will be attaching an optional printer you ll need a table top with at least 30 76cm of depth for adequate clearance Do not place the duplicator near heat sources such as radiators or air ducts or in a place subject to direct sun light excessive dust mechanical vibration or shock Allow for adequate clearance in front of t
4. dA 1 4 7 9 13 38 Thermal ii toi 1 4 8 9 14 38 PRN Files iii ia eii 31 32 PXE Files cid editan 31 32 RE CE ATCA 4 iii inn Conds doi di O PIE 3 8 29 Resetting the Duplicator cece ce ee ceeeeeeeteneneesenees 34 Selecting Diven w A A la 21 Software Installation Didi atico 20 Operating Scre S soisin isise ernro eiii iiss 27 JESU Bsc ada TT 22 Specifications ini da hw Ad 38 Stands Printer nia ta 9 13 14 15 19 System Requirements ccoocccconinnonnononnnnonncnnararocnnnaroricnonororirannonos 10 Technical Support rrene aria 37 Tray Support Bracket o oocinnnncococoninonicinananonononcnananonononononanononononos 9 Troubleshooting AAA a UA io 34 Unpacking wedi oo A rzy 6 Index 41 Printed in the United States of America P N 510140
5. file to be saved in If your application does not have a print to file option then you must change the printing mode under the printer properties Right click the printer icon from the printers folder and select properties Next if using Windows 95 98 ME select the details tab Under the setting Print to the Follwing Port change it from LPT1 to File this is an option just select the drop down arrow If using Windows NT 2000 select the ports tab and select the File option Which ever system you have any time you try to print using that driver you will be prompted for a file name and location This will create a prn file Note When creating print files make sure that the 32 Bit Spooler and Direct to Port options under printer properties are not checked You will encounter problems if they are checked 2 PXF files These are created using the Prassi Disc Face Editor software that is built into the Prassi PrimoDVD Pro 2 0 To use Disc Face Editor go to Tools Disc Face Editor The program launches Full instructions for its use are in the Prassi User s Guide Once you have created your image store it in a directory where you can later find it when you need to call it from your Image Job window 32 Running Your First Job TOC INDEX Section 4 Interpreting the Duplicator s LED Status Lights The LED Status Lights are located on the front Control Panel They can tell you a lot about what is happening at any given moment
6. is where you stack blank discs which are to be recorded and printed The Output Bin is where discs are stacked up to 50 at a time after they have been recorded and printed by the Duplicator The Reject Area is where discs are dropped if they do not pass a software verification test Discs simply drop on the table top in front of the left front side of your Duplicator In most cases rejected discs should be discarded This is usually indicative of a disc manufacturing problem If one brand of discs seems to be rejected frequently you ll probably want to try using a different brand For reference the illustration below shows the optional Thermal CD Printer attached to the Duplicator Note that the Thermal CD Printer attaches to the left side of the printer and that the Output Bin is located in a different spot due to the location of the Thermal CD Printer When you first power up the Duplicator it will automatically do a search for where the Input and Output Bins are located and from then on will know where to pick and place discs 8 Getting Started lt a TOC INDEX When using the Thermal CD Printer you will also need to attach a Tray Support Bracket to the top cabinet of the Duplicator Follow the instructions packed with the optional Printer Stand for the Thermal CD Printer Rear Panel This illustration shows the input ports found on the rear panel of the Duplicator Power Input Port Printer Control Port Con
7. may be loaded at one time into the Input Bin of the Duplicator The Duplicator Plus will hold up to 100 discs Input Bin 2 The Duplicator has an integrated robotic arm that picks discs one at a time from the Input Bin 3 The CD Tray on the built in high speed CD Recorder opens automatically and the Robotic Arm places the disc into the recorder 2 Getting Started lt a gt TOC INDEX The CD Tray on the CD Recorder automatically shuts Through software control you can perform a verification test on each CD R disc before recording If a disc does not pass meaning that all or part of that disc is not recordable the Robotic Arm picks it out of the CD Tray and sends it to the Reject Area located at the front left side of the Duplicator Rejected discs simply drop onto your table top in this area Since most CD Rs available today are of extremely high quality you will rarely reject a disc Nevertheless it is good practice to verify each disc just in case You certainly don t want to send out a great looking disc that does not read properly in your customer s CD drive Keep in mind that verifying each disc will add extra time to the recording process The CD R is now recorded If you were to fill up each CD with data audio video or music 650 MB recording time is about 6 minutes each Most jobs don t fill the entire CD R so recording time is usually less than this Getting Started 3 de TOC INDEX
8. or III and the RAM should be at least 128mb 10 Getting Started TOC INDEX Section 2 Hardware and Software Set Up and Testing A CONNECTING INTERFACE CABLES 1 Make sure that your PC is turned off and that it is disconnected from its power source Leave the PC turned off until you are requested to turn it on later in this set up procedure Install a compatible FireWire board inside your PC Please refer to the board manufacturer s instructions for the proper installation procedure Connect the FireWire cable One end is connected to the FireWire port on the rear panel of the Duplicator The other end is connected to the FireWire board s output port on your PC Hardware and Software Set Up and Testing 11 lt a gt TOC INDEX 4 Connect the Serial Interface cable One end is connected to the DB9 connector on the rear panel of the Duplicator The other end is connected to your PC s DB9 COM1 port If COM1 is already used for another device you can use COM2 or COM3 and follow on screen instructions later in the set up procedure for changing the default serial port for the Duplicator 5 Apply power to the Duplicator One end of the power adapter s cord is attached to the power input port on the rear panel of the Duplicator The other end is connected to a suitable wall outlet Use of a high quality commercially available surge suppressor is highly recommended 6 If you will be printing as well a
9. software according to the instructions in that unit s Operator s Manual 2 Install PrimoDVD Pro 2 0 software as follows a Close down all other software applications b Insert the included CD into your computer s CD ROM drive In most computers the software will auto boot If it does proceed to Step 3 below If it does not follow these steps e Double click on My Computer e Double click on your CD ROM drive containing the installation disc e Click Install Prassi PrimoCD Pro or Prassi DVD Pro 3 The Prassi Welcome Screen is now displayed Press Next 4 The license agreement screen is displayed After reading it press Yes to continue or No to leave the program 20 Hardware and Software Set Up and Testing lt a gt TOC INDEX 5 Assuming that you pressed Yes the next screen shows the Destination Location If you wish to install the program in a different location press Browse If not press Next 6 The Show Program Folder screen is displayed If you wish to change the name of the folder in which the software will be installed do so now If not press Next 7 The installation progress will be displayed When the program is completely installed you will see Set Up Complete Press Finish 8 Re boot your computer before you proceed E SELECTING YOUR RECORDER DRIVE If your PC has one or more recording drives in addition the drive in your Duplicator the following window will be seen each time Prassi Primo CD
10. ydy o i O ROG a Wawa 40 iii Interactive Feature in this PDF Document There are interactive features that will allow you to jump to different locations within the document Each listing in the Table of Contents is interactive Place the cursor on either the words or the page number A small hand with a pointing finger icon appears Click on the line with the icon and the document will jump to that page If you want to return to the Table of Contents move the icon to the top of the page and click on the arrow marked TOC Navigating through the Index is similar Place the icon on one of the listings or page numbers click on it and it will move to that page The text relating to the Index listing will appear in red Returning to the Index can be done by clicking on the arrow marked Index lt a TOC INDEX Section 1 Getting Started THANK YOU for purchasing the Optical Disc Duplicator or Optical Disc Duplicator Plus It is the perfect way for you to copy CDs The Optical Disc Duplicator handles 50 discs at a time while the Optical Disc Duplicator Plus has 100 disc capacity You can also print directly onto disc surfaces with an optional ink jet or thermal printer A wide variety of disc formats are supported including Audio CDs Video CDs data discs and more Operation is simple and totally automatic once a job has been started To begin using your Duplicator please read this manual carefully This Operator s Man
11. E AM ih Y zepina t PRIMERAS 4 o alapa seen inei Melee ate M gon DSi Oem TA uaan ty u mac AT E A Fomwawe E c Examine the type of recording job you are attempting If you are attempting to record directly from a CD Reader to the Duplicator the reader or the bus inside your computer may not be able to keep up with recording at 16x speed Try creating a global image GI of the disc as described earlier in this manual and you will most likely have greater success 36 Maintenance and Troubleshooting 4 gt TOC INDEX E TECHNICAL SUPPORT If you have difficulties in operating your Duplicator the procedures in this manual and the Prassi software User s Guide should in most cases solve the problem If you still have difficulty contact the technical support number listed on the insert included in the supply pack that came with your Duplicator Maintenance and Troubleshooting 37 K TOC gt INDEX Model Configurations Optional Printers Minimum System Disc Capacity Recordable Formats Optical Disc Duplicator CD R System One CD R recorder Prassi PrimoCD Pro Software Robotic Transport Station DVD R System One DVD R recorder Prassi PrimoDVD and PrimoCD Software Robotic Transport Station Print Only System Printer Autoloader Robotic Transport Station only controlled by Ink Jet CD Printer or Thermal CD Printer Ink Jet CD Printer or Thermal CD Printer Pentium II II P
12. Pro is launched PrimoCD for Primera x R Optical Disc Duplicator OK Cancel Choose the drive in your Optical Disc Duplicator If you are unsure try each Open Close button to determine the proper drive SELECT Recorder at Host 2 ID 4 Generic CRD BP4 4 28 Open Close Recorder at Host 2 ID 5 Generic CRD BP4 4 28 Open Close e Recorder at Host 31D 0 Pioneer DVD RW DVR 103 1 44 Hardware and Software Set Up and Testing 21 lt a TOC INDEX This dialogue box will allow Prassi to identify the drive in your Duplicator Each recording drive installed on your system will be listed in this dialogue box Click each Open Close button to ope the recorder drive then click the appropriate SELECT radio button for the drive installed in your Duplicator F SOFTWARE TEST The final set up step before starting your first job is to test the entire hardware software configuration This will confirm that the hardware software and your PC are all communicating properly with each other properly Follow this procedure 1 Launch the Prassi software from your Windows Desktop or program menu The main Application Window will appear Single click on the Duplicator drive in the list of available drives on the lefthand side of the screen to high light it 2 From the main Application Window click on Robotics BIO HoarliDOEJ es Em oo 7 a ss g A TIZD PAS 4 vr Wr py fol Aa NEPA a 22 Hardwar
13. VD Pro 2 0 Software from your Windows Desktop or program files 2 Insert the master disc into your PC s CD drive In the drive list right click on the Host Drive and select Disc Explorer and Drive Properties 3 The Disc Explorer Window will be displayed Check in the Disc Explorer that the source disc is correctly read Click on the Force Refresh Button if the Auto Refresh checkbox is not checked 4 Press the big Global Image button In the panel that appears at the bottom of the Disc Explorer enter the file name that will contain the disc image uses a GI extension Then press Build Please note that this method of building a disc image creates a saved file on your computer s hard drive These files can get huge up to 650MB each You may want to create only a temporary image that is automatically deleted after your copy job is done To do this instead build your job image file using the Disc to Disc option from the main File New Job drop down menu Be sure to click the checkbox that reads Make a Temporary Image on the Hard Disc and Copy From There The job will build automatically make the number of copies you ve specified and delete the disc image afterwards 5 Wait until the image is completely built and then close the Disc Explorer dialog 6 From the Menu bar select File New Job or New Global Image or Other Image Job A Job Window will now open in the right side of the application 30 Running Your First J
14. a This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada CAUTION TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE EXTERIOR PANELS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL OPERATE THE UNIT WITH ONLY THE PROPER ELECTRICAL SPECIFICATIONS AS LABELED ON THE PRINTER AND AC ADAPTER CAUTION THIS PRODUCT CONTAINS A LASER DIODE OF A HIGHER CLASS THAN 1 TO ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF THIS PRODUCT REFER ALL SERVICING TO QUALIFIED PERSONNEL THE FOLLOWING LABEL APPEARS INSIDE YOUR UNIT CLASS 1 LASER PRODUCT LASER KLASSE 1 CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION NOTE The optional DVD R drive inside this product has laser diode s emitting below the limits of Class 3B ii gt INDEX Table of Contents Section 1 Getting Started ssesssseessessessesssoressessesreosesse
15. age Job dialog box set the number of copies the speed if you select a speed that the recorder does not support it will default to the immediate lower one and the action you desire Test Test and Record Record Verify and Record etc Press the red Record button to start recording your copies If everything worked right the Duplicator should now be recording and printing your discs Running Your First Job 31 4 TOC INDEX D CREATING PRINT FILES Two types of print files are supported in PrimoDVD Pro 2 0 1 prn files and 2 pxf files Each are explained below 1 PRN files First and foremost a prn file is created by printing it is not saved in the conventional manner The prn has all of the driver properties built into the file at the time of creation Once this file is created it can not be changed Example If a print file was created with the cartridge type set to color you can only print using color If you change to a monochrome cartridge the prn will not work Print files can be created from any Window s based graphics application Most applications have a check box in the print window for printing to file If this is the case run your print to the printer to make sure that all settings are correct Once you are to the point of making the print file just select print then in the print window select the Print to File checkbox A window will pop up prompting you for a file name and location for the
16. at Top or Show at Right from the drop down menu gt dd Iwa PTY Su nr Tae TOTTE ku BEET Aa 2 EA A rT ae e p j J 14 HOT PRIMERAS 4 o J diapa entecat Melendo e 11M Beet A271 TS SRT turan Gotowe Mawel ATAN TT 4 Epa This will show a history of tasks performed by Prassi If there are errors you will see them in this list For more information on recording errors you can consult the Prassi manual included with the Duplicator The most common error is Buffer Underrun This occurs when data can not be sent fast enough to keep up with the recording drive The following suggestions are very useful in eliminating buffer underrun errors Maintenance and Troubleshooting 35 gt TOC INDEX a Click Tools Options and check the box labeled Enable Burn Proof This option enables the drive to slow down its recording speed to match the data E Runnin minge fran tre Liyana alit EF MT ALA E Dupe whet ap Boso u Praka Duelos tiwa O Manet tw ct andaria 1 mc ct set Hania shan adc k a rzad ni Ln ki AS i voto Ford Mea D bth BREN Pl TIA F Baw s 4 o I Bom Aim 57167 3F1 that at plac red Direc la tree rea wad ada e we i ipa Piata ninen Mob er IK b Click Robotics Options and deselect Record and Print Simultaneously This will cause your jobs to take longer but will free more computer resources for recording r y me Div IBAN Del Pad T O Mei RA W
17. b and walking away Verifying will compare the data of the recorded CD R with the original information This takes extra time but ensures that the recorded CD R is an exact match After your job s have been set up each one may be started by clicking on the red Record Button at the top of the Job Setup Panel Here s what the Job Setup Panel looks like Pause Button Record Button Stop Button While jobs are running they may be paused or stopped by clicking on the appropriate buttons on the Job Setup Panel The Pause Button will allow the current recording to finish then suspends operations on that job Recording is resumed by clicking the Pause Button again The Stop Button will abort any recording in progress and cause the Duplicator to transport the disc to the Reject Area It will also terminate that job Record Stop and Pause actions for the currently selected highlighted job may also be selected from the Toolbar at the top of the main Application Screen Running Your First Job 29 lt a TOC INDEX C COPYING AN AUDIO CD Now you re ready to start an actual recording job In this example we ll perform a simple audio disc copy More detailed information regarding other types of jobs data discs Video CD etc can be found in the Prassi User s Guide and in the Help files included on the main Application Screen Toolbar Follow these steps to set up and perform an audio CD copy job 1 Launch the PrimoD
18. e and Software Set Up and Testing gt TOC INDEX In the drop down menu go to Services MLS Hat 10 05 Bo ATA Fry ERAS PRIM SrrimoCd for Primera Click on Check Communications You will get a dialog box saying Communication OK System Idle If you don t check that all cables are connected securely Or change the from on your PC to and change the setting in the drop down menu Try again until you get the Communication OK message 3 rrimaCD for Primera Click OK to get back to the main screen Hardware and Software Set Up and Testing 23 lt a TOC INDEX 6 Click on Robotics again NT AAA PAS he J hala fOr gt PRIMERA Dirt ny Hr y 7 PRIMERA 24 Hardware and Software Set Up and Testing gt TOC INDEX 8 Deselect any components you don t have installed in the check boxes in Multiple System Test Hrn p TRIMERS 9 Load at least 4 5 discs into the Input Bin 10 Click on Start Test The robotic arm will move through its entire sequence automatically If you specified more than one disc it will continue until the number you specified is completed or it runs out of discs Jo PRIMERA Congratulations You have now completed the installation process and your Duplicator is ready for operation Hardware and Software Set Up and Testing 25 4 TOC INDEX NOTE Prassi Primo PrimoDVD Pro 2 0 software is for use only with Windo
19. he printer to accommodate the length of the unit with its recorder s CD Tray open You will also need an area in front of the unit for rejected discs to fall C UNPACKING AND INSPECTION While unpacking your Duplicator inspect the carton to ensure that no damage has occurred during shipping Make sure that all supplied accessories are included with your unit The following items should be included e Duplicator e Gray Plastic Input and Output Bins e Power Adapter and Power Cord Serial Control Port Cable IEEE 1394 FireWire Cable e Application Software Installer CD R e Warranty Statement and Registration Card e This Operator s Manual Quick Start Guide and Other Printed Information Save the carton and packing materials They will come in handy later if you ever need to transport the Duplicator and or any of its parts and accessories Transporting the unit without the proper packaging can cause damage to the robotics 6 Getting Started lt a TOC INDEX D IDENTIFYING THE PARTS Front Panel and Top This illustration shows the Duplicator its Control Panel Buttons LED indicator lights Input and Output Bins and other components An optional ink jet CD printer is shown with the unit so that you can see where it is attached Ink Jet CD Printer CD Printer Tray Input Bin Robotic CD Recorder Tray CD Recorder CD Recorder Tray Button LED Status Light Pick Button Control Pa
20. ize windows that indicate what you ve setup and what s happening the Drive Status Window the Job Status Window and the Job Setup Window A sub Window called the Activity Log is also available but it is hidden upon initial boot up of the software Here s a short explanation of each Window e Drive Status Window Lists all of the drives installed in the system Your configuration has just two drives the internal drive in your PC and the CD Recorder installed in your Duplicator Running Your First Job 27 de TOC INDEX Job Set Up Window This is the space where the Job Setup Panel for each job is displayed When you select a job by clicking on File New from the File pull down menu a different type of Job Panel will appear in the Job Set Up Window depending upon the type of job selected Each Job Panel contains all of the necessary information to run that job including source file name number of copies to make etc In addition the Job Panels reports status information during the running of the job e Job Status Window As each Job Panel is formed an entry is made in the Job Status Window at the lower left side of the main Application Window When jobs are started this list displays the status of each job including the number of discs copied and the number remaining This window may be hidden by clicking on the Show Job List Panel under the View menu One other sub window available is called the Activity Log Panel It record
21. lass B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of a shielded cable is required to comply with the Class B limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate and or obtain warranty service for this equipment This product is intended to be supplied with a UL Listed Direct Plug In Power Supply marked Class 2 or a UL Listed ITE Power Supply marked LPS with output rated of 24 V dc 2 5 A For Users in Canad
22. lel cable One end is connected to the parallel port on the rear panel of the printer The other end is connected to the parallel port of your PC Make sure that your PC s parallel port is set to ECP mode If you don t know how to check this or how to change it refer to set up section of the printer s Operator s Manual 11 Make sure that all cables are routed neatly underneath and out the back of the printer stand and that no cables are underneath the Duplicator or printer stand feet Hardware and Software Set Up and Testing 15 de TOC INDEX 12 Apply power to the printer One end of the Power Adapter is connected to the printer s rear panel Power Input Port The other end is attached to a wall outlet You have now completed the hardware and cabling set up Continue on to the Hardware Test and Printer Alignment procedures in the next section B HARDWARE TEST AND PRINTER ALIGNMENT 1 Power up your PC by re connecting its main power cord Turn on the PC with its power button 2 While waiting for Windows to start perform a Hardware Test as follows a Place the gray plastic Input and Output Bins on top of the duplicator 16 Hardware and Software Set Up and Testing de gt TOC INDEX b Puta stack of blank CDs in the Input Bin the one on the right side c Press the Sequence button on the Duplicator s front control panel The Robotic Arm will swing around to do an initial check to optically detec
23. n MIND DIN ica 13 15 Serial AA A ana 6 9 23 Connections Rear Panel oonnonccnnnnnccccncoonconcoononncoononnnonnonnnonnonncnnos 9 Controls Front Panel e eeuae aaa aaa aaa aaa aaa wiwa 7 Disc Face Eqitot iio ia PAC 31 32 FireWite EE EEE EA A EET 6 9 10 11 39 Hard Ware Testi ie aaa ses esses 16 20 Identifying the Parts ci cc ccecsscssenssiestesaseveedoeeisvenssuesevensbevessvenseun 7 LED Status Lights een nseni siia eiiie 7 33 Locating Holes Printer onnnncninnnnnnnnncnnnnoninononononanonononanaranonononos 14 EOcaUom ice ee Se A e De SI 6 Maintenance cial osi aikido 34 Overview of Operation cc ceseseecesenssssseeseneneeeeesees 2 Overview of Recording e ee aa 28 Parallel Interface Cable WZA OOO APO 11 15 ECP MOdE sia idac to re ere eS 15 Ports COMT COMZ2 COMS saw ca 9 12 23 Control iis ania ne aio ea ees 9 23 Printer Control ccccccccccssccessecsssessceceseeeseceseeeseeeseecees 9 13 15 Power Mputa aroni e rra e E saaat 9 12 40 Index 4 TOC PrimoCD Pro Software Activity LOS n Ao ind GA 27 28 Application Window aaa aaa 22 28 Drive Status Window wawa awa naa 27 Job Status Window cceceeeeccseessesseseceeeceeseeseeeeeeceaeneeeeeaes 27 28 Job Set Up Window anawa 27 28 Print Files CREAN zana ian w inna A Rain 32 TYPOS Ra dat i Aa 32 Printer Driver Software ee eeeuae aaa aaa 20 26 Printers Ink Jet ec titre di
24. nel Sequence Button Reject Area Pause Button The CD Recorder is where the Duplicator loads discs as they are copied one by one The Robotic Arm transports discs from the Input Bin to the CD Recorder to the printer and finally to the Output Bin The CD Tray Button manually opens or closes the CD Tray In normal operation the in out movement of the CD Tray is controlled automatically and this button is not used The Control Panel contains LED Status Lights and Buttons to manually control operation of the duplicator The LED Status Lights indicates that Power is ON and when the Pause Button has been pressed They also blink in certain patterns to indicate an error or other condition of the Duplicator See Section 4 for a full explanation of the LED Status Light conditions Getting Started 7 de gt TOC INDEX The Pause Button immediately pauses the motion of the Robotic Arm Itis also used in combination with other buttons to perform certain reset and error clearing operations The Sequence Button moves the Robotic Arm from one position to the next Is is used mainly during the set up and testing procedures Itis also used in combination with other buttons to perform certain reset and error clearing operations The Pick Button is used to manually pick up a disc and to drop it in a Bin the CD Recorder or the Reject area Itis also used in combination with other buttons The Input Bin is on the right side of the Duplicator This
25. ob 10 11 12 de TOC INDEX In the Image Job dialog box enter the name of the GI file you just created into the Image field name A drop down box will contain all the recent images you created and you can easily select from this list if you choose Also in the Image Job dialog box check the box labeled Print if you have a printer installed and wish to print a print image onto each disc after it has been recorded There are two types of files supported 1 prn files you ve previously created using almost any Windows graphics application or 2 pxf files that have been created with the built in Disc Face Editor software Both graphics file types and how to create them are explained in Section D NOTE It is highly recommended that you use PRN files for printing as opposed to PXF files PXF files may not print properly PRN files are the recommended way for printing on any operating system In the drop down box to the right of the Print checkbox you can select any recently used pxf or prn files Or click the box next to the print dialog box to browse for saved pxf or prn files Find the file you wish to print highlight it and click Open Or double click on it The file appears in the Image Job Window print dialog box with its path In the Drive List highlight the recorder icon This is where the software will send the job for recording Right click on the icon and select Select Deselect as Recorder In the Im
26. rays Stronger cleaning solutions are NOT recommended because they may damage the paint and plastic materials from which the parts are manufactured Always disconnect your Duplicator and printer s power cords before cleaning Resume operation only after the surfaces are completely dry B RESETTING THE DUPLICATOR If you find yourself in a situation where the Duplicator is not responding properly you may need to do a system reset A typical cause may be when you stop a job out of sequence To do so press the Pause and Pick buttons at the same time Do NOT be tempted to simply unplug the Duplicator s power cord This will shut down the Duplicator s internal SCSI CD R drive and force you to completely restart the PC to re initialize the drive C SCSI POWER DOWN PROCEDURE As you may know SCSI is a very finicky interface You can not simply unplug cables or power down out of sequence since drive locations will be lost PCs can freeze up and other nasty things can happen To power down always shut down your PC first then unplug the Duplicator Use the opposite procedure for power up Always start the Duplicator first then turn on your PC 34 Maintenance and Troubleshooting lt a TOC INDEX D RECORDING ERRORS If discs are not being recorded properly or are not passing verification you will want to consult the error log This is available in Prassi by clicking View Activity Log then selecting the option to Show
27. rocessor or equivalent at 450 Mhz or higher 128MB RAM available PCI slot SCSI controller card Advansys ASB3940UA or compatible one free serial port one free parallel printer port Optical Disc Duplicator 50 disc input 50 disc output Optical Disc Duplicator Plus 100 disc input 100 disc output CD R CD Audio CD DA CD ROM CD I Video CD MP3 to CD Audio on the fly no hard drive overhead required Pioneer AO3 General Purpose DVD R DVD R Writes DVD R 4 7 General Only DVD RW CD R CD RW Reads DVD ROM DVD R all types DVD RW CD ROM CD TEXT Photo CD CD DA CD Extra 38 Technical Specifications de TOC INDEX Operating Systems Windows 98SE XP 2000 Interface Control PC serial port Printing PC parallel port Image data IEEE1394 FireWire 16x CD R SCSI Power Requirement 100 240 VAC 50 60 Hz 60 watts Weight 12 5 Ibs 5 67 kg Dimensions 16 625 W x 10 H x 10 125 D 422mmW x 254mmH x 257mmD Certifications Emissions FCC Class B CE Safety TUV GS cTUVus CE Warranty One year return to depot Technical Specifications 39 4 TOC Application Wind0W ooonioininnnnnnninnnincnnnnncncnrncncnrarornrncnnos 22 27 28 Audio Job RUNDING heee ipiis A A RE 27 Bins A O a Ea ais 6 7 8 16 DU puta data nowi eine 6 7 8 16 Buttons CD raj powita a p asi on A 7 17 Piu s n Al thet Hite ie ihe WAN ee 7 8 29 PICK oh di O A CAO 8 17 19 20 34 A A 8 17 19 20 Cables 6 Pi
28. s all user actions and system responses during the recording process by time of occurrence If a problem occurs while you re not present in front of the computer you can browse the log to find out details that may no longer be present on the main screen Control of the Activity Log is under View Activity Log The log may be saved this happens automatically every time you exit the software Emptying the log will delete the entire log B OVERVIEW OF RECORDING Three basic recording operations are available 1 actual recording 2 test recording and 3 verifying Actual recording is self explanatory Discs will be recorded without any testing or verifying beforehand If you have used the Duplicator successfully before with a particular brand of media that is highly reliable you may choose to record without testing or verifying This will deliver the highest throughput rate of finished discs Test recording performs all of the operations of recording with the drive s laser turned on to reading power A test recording run will determine if the data source will keep up with the recorder s demand Normally a single test run is sufficient to determine if a condition knows as buffer underrun will occur If a buffer underrun occurs during recording all the discs that are run through your CD Recorder will be wasted So a quick 28 Running Your First Job lt a TOC INDEX test recording is highly recommended before starting a jo
29. s duplicating discs setup the printer according to its instructions and continue on to step 7 If you won t be attaching a printer you have now completed the Hardware and Cabling Set Up procedure Proceed to Section B 12 Hardware and Software Set Up and Testing lt a TOC INDEX 7 Connect the 6 pin mini DIN cable included with the optional Printer Stand to the Printer Control Port on the rear panel of the Duplicator Do not connect the other end yet You need to attach the Printer Stand and mount the printer first 8 Attach the optional printer stand required for a printer installation to the Duplicator by locating the connecting tabs and inserting them into the slots on the rear panel of the Duplicator For the Ink Jet CD Printer the stand is attached in the center of the Duplicator S U 07 Hardware and Software Set Up and Testing 13 de gt TOC INDEX For the Thermal CD Printer the printer is mounted on the left side of the Duplicator For either printer find the locating holes on the bottom plate of the printer Position the printer on the stand so that the printer stand locating pins are inserted into the locating holes of the printer 14 Hardware and Software Set Up and Testing de gt TOC INDEX 9 Connect the other end of the 6 pin mini DIN cable to the Printer Control Port on the rear panel of the printer 10 Connect the printer with an IEEE 1284 compliant paral
30. ssesneosessesseoneoressessesse 1 A Overview of Operation cd tc ueaeaebbe 2 B Choosing a Good Location ccccincnnininnnninonenennnnnnnnnananin ran arononononicncnnos 6 C Unpacking and hspech On wc dO ORA Gej 6 D Identifying the Falowniki AE OKR 7 E System Requirements u ee eee 10 Section 2 Hardware and Software Set Up and Testing 11111 11 11 A Connecting Interface Cables aaa 11 B Hardware Test and Printer Alignment cece 16 C Fine Tuning the Printer Stand Alignment ee 19 D Software Installation aaa 20 E Selecting Your Recorder Drive oo eee 21 E Software Test we a a cidad 22 Section 3 Running Your First JOD csssssssssssssesesssessesssesssesseeeeeesees 27 A Operating Screens orere eee 27 B Overview of Recording ueus usenecie 28 C Copying a Mudo CD siii ja 30 D Creating Print Files AA A 32 Section 4 Interpreting the Duplicator s LED Status Lights 33 e Power LED concisa ica 33 Bev Pause LED oia ii cata 33 Section 5 Maintenance and Troubleshooting omocononooams mmss s 34 As Cleaning the Cassini 34 B Resetting the Duplicator uee eee 34 C SCSI Power Down Procedure cece anna 34 D Recording Errors sissies diccisseseeitscscevteenseshctenaessasantes BOO 35 E Technical Supports asa do od A Owad die 37 Section 6 Technical Specifications u cscs cesesseeseseseeeseseeees 38 Index
31. t which printer is installed It will then go to a position directly above the Input Bin d Press the Pick button on the control panel The robotic arm will pick up a disc e Open the CD R Recorder s CD Tray with the CD Tray button f Press the Sequence button g Press the Pick button The CD will be placed into the CD Tray h Press the Pick button again The CD will be lifted out of the CD Tray Hardware and Software Set Up and Testing 17 de TOC INDEX i Open the printer tray with the disc in out button On the Ink Jet CD Printer this is the button with the two arrows pointing different directions On the Thermal CD Printer this is the button on the lower right side of the front panel A s38 29 j Press the Sequence button k Press the Pick button The CD will drop into the printer s tray If it does not drop perfectly into place you will need to adjust the printer stand s Mounting Plate This is accomplished by loosening the three Phillips head adjusting screws and moving the printer slightly in one direction or another until the disc is dropped perfectly into the printer s tray You can repeatedly press the Pick button to test your alignment Or press and hold the Pick button for 5 seconds then release it and the disc will be positioned about 5 mm above the tray for easy visual alignment When the alignment is correct tighten down the screws securely 18 Hardware and Software Set Up and Testing
32. trol Port FireWire Port The FireWire IEEE 1394 Port of the duplicator is for connection to your PCs internal FireWire board The Control Port is connected to COM1 or COM2 or COM3 of your PC with a serial cable included with your Duplicator The Printer Control Port is connected to the mini DIN plug on the rear panel of a Thermal CD Printer or an Ink Jet CD Printer with a mini DIN cable included with the optional printer stand The Power Input Port is for connection to the 24V Power Adapter included with your Duplicator Getting Started 9 de TOC INDEX E SYSTEM REQUIREMENTS Before getting started it is important for you to verify that your PC meets the minimum system requirements Here s what you need in order to successfully copy discs at 8x or above using the Prassi software e 450 MHz or faster processor 128MB or greater RAM e Video display capable of 1024 x 768 pixels e Free hard drive space of at least 2 GB If your PC does not have at least these minimum system requirements you probably do not want to install the FireWire SCSI board and software on that PC System performance will more than likely not be acceptable For example you may find that your top recording speed will be limited to only 4x Your Duplicator is capable of much higher performance so why limit it due to a slow PC To print and burn simultaneously you will need more RAM or a faster processor The processor should be a Pentium II
33. ual is a complete step by step guide to quickly and easily setting up and beginning to copy discs with your new Duplicator A separate User s Guide is provided with your Duplicator that explains the operation of the Prassi PrimoPro CD or PrimoDVD Software NOTE ON TERMS AND CONVENTIONS From this point forward the following terms and conventions will apply 1 Both the Optical Disc Duplicator and Optical Disc Duplicator Plus will be abbreviated as the Duplicator 2 Optical discs which can include many different types of discs including CD Rs CD RWs DVD Rs and more are all referred to as CDs or discs Please note that in order to copy and record DVDs you need to have purchased the DVD R version of the Duplicator 3 This manual assumes that you will be attaching a printer to the Duplicator It further assumes that you will be using the Ink Jet CD Printer CD Printer IV If you are attaching a Thermal CD Printer or any other ink jet CD printer virtually all of the same set up instructions are valid In either case you will need to consult the printers own Operator s Manuals for details on printer operation Getting Started 1 lt a TOC INDEX A OVERVIEW OF OPERATION Your new CD Duplicator is an automated precision device intended for continuous duty copying and printing of CDs The following is a description of the complete process of copying and printing a CD job on your Duplicator 1 Up to 50 blank CD Rs
34. uplicator toggle back and forth 4 Immediately press the Pause Button to enter the Fine Tune Mode 5 Next press the Duplicator s Pick Button to perform the Printer Tray Fine Tune Alignment The Robotic Arm will move to the printer position and hover just above the Printer Tray Hardware and Software Set Up and Testing 19 lt a TOC INDEX 6 With the Robotic Arm holding a disc just over the tray move the printer around until aligned as close as possible For a more accurate alignment press the Sequence Button to step the arm slightly to the right clockwise or press the Pause Button to step the arm slightly to the left counter clockwise 7 With the printer aligned tighten the three Printer Stand Adjustment Screws 8 Press the Pick Button to exit the Fine Tune Mode 9 Test your alignment by pressing the Pick Button repeatedly to pick and place a disc into the tray You have now completed the Hardware Test and Printer Alignment Continue on to the Software Installation D SOFTWARE INSTALLATION Once you have properly set up your Duplicator and optional CD printer the next step is to install the appropriate software on your PC that you ll need for duplicating and printing There are two software programs to install 1 the printer driver software and 2 the CD duplicating application software called Prassi PrimoDVD Pro 2 0 Install the two software programs as follows 1 Install the printer driver
35. with the Duplicator including a number of error conditions To accurately interpret what is meant when the lights are on off or flashing please refer to the following chart Power LED Pause LED A POWER LED Status Condition Off No Power Plug in Power Adapter On Solid Power is ON This is the Duplicator s normal waiting mode Flashing Power is ON but an error condition exists a Didn t pick up a disc b Dropped a disc c Discs out d Robotic arm stalled probably hit something while moving Press any button on Control Panel to re try B PAUSE LED Status Condition Off Normal waiting mode On Solid Duplicator is paused Flashing Duplicator is busy i e motors are running printer is printing etc Interpreting the Duplicator s LED Status Lights 33 TOC INDEX Section 5 The Duplicator is designed to operate for extended periods of time with very little attention In fact no regular maintenance is recommended other than cleaning the outside case NOTE Do NOT attempt to oil or grease the Duplicator s Robotic Arm shaft or other components You will likely cause more harm than good Any moving parts are designed to be run for the life of the machine with no additional lubrication required A CLEANING THE CASE Use a clean white rag with a small amount of water or isopropyl alcohol to clean the Duplicator and printer s outside cases and CD t
36. ws 98SE Windows 2000 or Windows XP A Macintosh version is not available The next section of this Operator s Manual will guide you through a simple audio disc copy procedure For information on performing more advanced copying jobs or to learn how to copy Video CDs data discs and other formats consult the separate Prassi PrimoDVD Pro 2 0 Operator s Guide included with your Duplicator An excellent on line Help file is also available from within the Prassi software as well as from the printer driver software 26 Hardware and Software Set Up and Testing TOC INDEX Section 3 Running Your First Job Now that you ve completed the hardware set up connected all cables loaded the Prassi PrimoDVD Pro 2 0 Software and the printer driver and performed all tests you re ready to copy discs The example given in this chapter is for a simple audio CD copying job using Prassi PrimoDVD Pro 2 0 software Please refer to the excellent Prassi Software User s Guide for instructions on performing other types of copying jobs There is also on line help available from the Prassi software s Help screens A OPERATING SCREENS To keep things simple there is really only one main operating screen you ll need to know about in order to run the Prassi Software It is called the Application Window and it looks like this Drive Status Window Job Set Up Window DATE Job Status Window Under this window there are several adjustable s
Download Pdf Manuals
Related Search
Composer/ComposerPlus composer/composer