Home

Catalogue

1. If you are using the recommended controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR output you need to use adapter cables Building a Serial DMX Chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected CAUTION At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohm resistor between Signal and into a 3 pin XLR plug it in the DMxX output of the last fixture DMX Channels DMX Channel Description DMX Channels Data Remark CH1 Strobe Dimmer 0 255 Dimmer plus strobe CH2 Color Wheel 0 255 Seven colors plus white CH3 Gobo Wheel 0 255 Six metal gobos plus one glass gobo CH4 Gobo Rotation 0 255 High speed rotation is available CH5 Gobo Shake 0 255 Shake up and down is available CH6 Pan 0 255 Rotate 540 degree CH7 Tilt 0 255 Rotate 270 degree CH8 Pan Fine 0 255 Pan jiggle CH9 Tilt Fine 0 255 Tilt jiggle CH10 Pan Tilt Speed 0 255 Control Pan Tilt speed CH11 Prism plus 0 255 From slow to fast Prism Rotation CH12 Focus 0 255 Multi step focus CH13 Reset 0 255 Renew factory state Addressing The control board on the front side of the base allow you to assign the DMX fixture the a
2. Supply Europe voltage 208 230 240V AC 50 60HZ Fuse TSA 250V The USA voltage 100 115 208 230V AC 50 60HZ Lamp HMI 575W Fuse T10A Power consumption 900W Optical System High luminous efficiency parabolic mirror and double condenser system All lenses are anti reflection coated Color Seven different colors interchangeable diachronic filters plus white color wheel with variable rotation speed Gobo Rotation Six interchangeable gobos plus white six metal gobos one glass gobo Strobe Strobe effect with variable speed 1 10 flashes per second Dimmer Smooth dimmer from 0 100 Prism 3 facet prism rotating in both directions at different speed Focus Can be controlled through DMX Mechanical multi step focus with three different angles 15 degree 18 degree and 22 degree Shutter Mechanical non step can be adjusted shutter are suitable for different line angles Effect Seven big prism gobos Preprogrammed and changing shutter pulse effect Motor 9 high quality stepping motor controlled by microprocessors Pan Tilt Pan movement range 530 degree Tilt movement range 270 degree Rigging Stands directly on the floor Use two clamps to install Two truss orientation Safety chain cord attachment point Temperature Maximum ambient temperature ta 40 degree Maximum housing temperature tb steady state 80 degree Dimensions and Weight Length of base including handles 520mm Width 520mm Height head horizo
3. Catalogue PEP OGUCHON 5 sccsaascenvecccenavedstsasine reks ea asn EEr E Seana 2 Features Description of the fixture Safety INStrUCHONS soesoenan nosies ns i Eoaea eas 3 4 The safety guides The operation limits PMSCAM AON ois nsc csi os Soa scetiad inosine isveteetesvesascdnosseweiseeeeet eavesenes oss 4 7 Fitting Exchanging the lamp Beam path Inserting Exchanging the gobos Rigging DMXS512 connection connection between fixtures DMX Chammels sissies ds eevee tevisaanp vaesendactigevaveavencdspeetetsindacussteasiwndss 7 Display and operating instructions DMX 13 channels instruction PROV OSSIING sessione aha oa vedas eda eae nase de exe e SETVE ESEE 7 8 Control Technical Specifications 5 lt 0ccccesccsccdvcsdtedssacevescceceedvedesedeseeesessvesits 8 9 Power supply Lamp Color wheel Fixed gobo wheel Rotating gobo wheel Three facet rotating prism Shutter Focus Dimmer shutter strobe Fans Motors Maintenance and Cleaning ccccccssccscccscsccscccsscccsccessccsssees 9 10 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initial start up Introduction Thank you for choosing our moving head light You acquired a versatile powerful and intelligent lighting effect Please unpack your casing and make sure that there are no damages caused by transportation Should there be any please refer to yo
4. ans the lamp is too back at the reflecting shelf Through adjusting three A B C screws at the same time and deasil 1 4 rotate to push out the lamp until the light is bright and distribute equably Rigging and Hook ePay attention to the safety e Please respectively consider the EN 60598 2 17 and the national standard during the installation The installation must only be carried out by the authorized dealer e The installation of the projectile shelf has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolishment eThe installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails eWhen rigging deranging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden eThe operator has to make sure that the safety measure and the machine s technical installation are approved by an expert before taking into operator for the first time and after changes before taking into operation anther time eThe operator has to make sure that safety measure and the machine s technical installation are approved by an expert after every four years in the course of an acceptance test eThe operator has to make sure that the relativ
5. c shock when touching the wire This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important statement Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems elf the device has been exposed to drastic temperature fluctuation e g after transportation do not open the light at once The agglomeration of vapor is likely destroying your product Do not open the product until it reaches normal temperature eThis device falls under protection class 1 The power plug must only be plugged into a protection class 1 outlet Never let the power cord come into contact with other cables Handle the power cord all connections with the mains with particular caution eMake sure that the available voltage is not higher than stated on the rear panel e Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord by the plug Never pull out the plug by tugging the power cord e Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord e During the initial start up some smoke or smell may ar
6. d gently pull the lamp out If you want to change the lamp remove the old lamp from the socket Do not install the lamp with a higher wattage If so the lamp will generate high temperatures and the device is not designed for that case Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer s announcement Do not touch the glass buld bare handed during the installation Make sure that the lamp is installed tightly into the lamp holder Reinstall the top cover of the head and tighten those 4 screws Do not operate the fixture with operate housing cover The brightness of the lighting has been aligned at the factory Due to the difference between lamps fine adjusted may improve light performance Strike the lighting open the grating and the diaphragm adjust the brightness to 100 and then focus the light on a flat surface e g wall Through using three A B C adjusting screws you can make the light focus on the hot spot the brightest of the light line Rotate one screw once to drag the hot spot through projectile shadow in the direction of diagonal Ifyou cannot find the hot spot adjust the lamp until the light line is even Through adjusting three A B C screws at the same time and deasil 1 4 rotate until the light line distribute equably then pull the lamp into doing so can reduce hot spot If the light in the edge is brighter than in the centre or the light output is very low it me
7. ddress which is defined as the first channel For example if you set the address to channel 5 this lighting will use the channel 5 to 16 for control Please be sure that you do not have any overlapping channels in order to control each lighting correctly and independently from any other fixture on the DMX data link Addressing setting 1 Turn on the moving head wait till finishing the reset RST flashes on the display 2 The main menu is accessed by pressing the MODE key press this one until the display shows message R001 Press ENTER to confirm 3 Use the UP and DOWN keys to select the required address 4 Press ENTER to confirm or press MODE to cancel Controlling After having addressed the lighting you may now start operating these via your lighting controller Note After switching on the lighting will automatically detect whether DMX512 signal is received or not If there is no signal received at the DMX input the display will not flash This situation can occur if The three pin XLR plug cable with DMX signal from controller is not connected with the input of the moving head light The controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm in the link in order to ensure proper transmission on the DMX data link Technical Specifications Power
8. e g due to cracks or deep scratches eThe objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly eThe gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet eThe diachronic color filters the gobo wheel and the internal lenses should be cleaned monthly eTo ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates eThere are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Please refer to the inserting and exchanging lamp chapter in this manual Replacing the Fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse of same tripe and rating Before replacing the fuse unplug mains lead Procedure STEP 1 Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing anti clockwise STEP 2 Remove the old fuse from the fuse holder STEP 3 Install the new fuse in the fuse holder STEP 4 Replace the fuse holder eShould you need any spare parts please use genuine parts elf the power supply cable of this device bec
9. e safety measure and the machine s technical installation are approved by a technician once a year eProcedure The projectile shelf should be installed outside areas where persons may walk by or be seated IMPORTANT MATTER Overhead rigging requires extensive experience including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury or property loss eThe projectile shelf has to be installed out of the reach of people elf the projectile shelf shall be lowered from the ceiling or high joists professional trussing systems have to be used The projectile shelf must never be fixed swinging freely in the room CAUTION Projectile shelf may cause severe injuries when crashing down If you have doubted concerning the safety of a possible installation do not install the projectile shelf eBefore rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight eDANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of minimum 0 5 meter CAUTION Use two appropriate clamps to rig the fixture on the truss Follow the ins
10. ise This is a normal process and does not necessarily mean that the device is defective eCAUTION During the operation the housing becomes very hot eNever frequently open close the lighting for reducing the life of the lamp eNever look directly into the light source as sensitive persons may suffer an epileptic shock especially meat for epileptics e Damages caused by non observance are not subject to warranty e Keep away children and amateurs Operating Determinations eThis device is a moving head spot for creating decorative effects And was designed for indoor use only eThis device is designed for professional use for example on stages in discotheques and theatres etc eLighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects eDo not shake the device Avoid brute force when installing or operating the device eNever lift the fixture by holding it at the projector head as the mechanic may be damaged Always hold the fixture at the transport handles e When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be cables lying around Make sure the safety of others and yours eAlways fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only eOnly operate the fixture after having checked that the housing i
11. ntal 700mm Weight net weight 28kg Shipping weight 30kg Maintenance and Cleaning The operator must make sure that correlative safety equipment and machine s technical installations are inspected by an expert after every four years in the course of an acceptance test The operator must make sure that correlative safety equipment and machine s technical installations are inspected by a skilled technician once a year The following points need to be considered during the inspection 1 All screws used for installing the devices have to be tightly connected and must not be corroded 2 There cannot be any deformations on housing fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rerate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed Danger High power Danger to life Disconnect from mains before starting maintenance operation e We recommend a frequent cleaning of the device Please use a moist flax to clean Never use alcohol or solvents eCAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired
12. omes damaged it has to be replaced by authorized dealers only in order to avoid hazards eShould you have further questions please contact your dealer We hope you will enjoy your lighting We can assure you that you will enjoy this device for years if you follow the instructions given in this manual
13. s firmly closed and all screws are tightly fastened eThe lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet which may cause burn e The maximum ambient temperature must never be exceeded CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g dug to cracks or deep scratches eOperate the device only after having familiarized with its functions Persons not qualified are not allowed to operate the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat ePlease use the original packing if the device is to be transported ePlease consider that unauthorized modifications on the device are forbidden due to safety reasons eNever remove the serial burial barcode from the device as this would make the guarantee void elf this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash Installation DANGER Install the lamp with the device switched off or unplug from mains Fitting Exchanging the Lamp Open the small lamp cover by loosening 3 screws open the small back cover at the back panel from the lighting an
14. tructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure eThe moving head light can be placed directly on the floor or rigged in any orientation on a truss without altering its operation character rustics There are two possibilities to fix the base of the lighting Use the rigging clamp to merge M10 or M12 screw please check the base For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety rope with screw on carbines Connection with the Mains Connect the device to the mains with the power plug The occupation of the connection cables is as follow Cable Pin International Brown Live L Blue Neutral N Yellow green Earth The earth has to be connected Pay attention to the safety Before taking into operation for the first time the installation has to be approved by an expert DMX 512 Connection Connection between Fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to controller with the fixture or one fixture with anther Occupation of the XLR Connection DMxX output DMX input XLR mounting socket XLR mounting plug 1 Ground 2 Signal 3 Signal
15. ur local dealer or our factory and do not take the device into operation Multi function moving head light trait eColor system One color wheel with seven kinds of different color diachronic filters plus white e One gobo wheel with six rotating metal gobos and one glass gobo rotating gobo can rotate to 360 eHigh speed rotating 3 facet prism eCombined shutter dimmer unit allowing very smooth dimming and strobe effect 1 10 flash second eThe lighting of the stock size eAddressing special functions setting effects calibration via control panel with 4 digit LED display eReadout fixture and lamp usage receiving DMX values temperature etc eMacro function for rotating gobo rerating prism combinations eBlack out while the light head moving or gobo color changing eRemote reset function eIntelligent control panel with 4 digit LED display eSilent fans cooling e13 DMX channels ePan movement rang 530 Tilt movement rang 280 eHigh luminous efficiency parabolic mirror and double condenser system eMechanical multi step focus eFocus is controllable through the mechanization of DMX ePreprogrammed changeable or stochastic grating pulse effect e All lenses are anti reflection coated e9 high quality stepper motors for smooth movement eSelf resettable thermo fuse eFor PHILIPS MSI 575W or OSRAM HMI 575W lamp Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electri

Catalogue

Contents

Download Pdf Manuals

Related Search

Related Contents