DESKLINE Controls Handsets User Manual
Contents
1. 4 5 11 75 80 8 3 i Sar RJ 27 DP1 Desk Panel DPF1K Desk Panel 18 5 DPF1C Desk Panel with display 130 Gay 28 DPF1M Desk Panel 179 9 29 WDP fitting for desk D D 110 gS 49 5 25 7 LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware software technical advice etc related to an existing or new customer application LINAK products as defined above are applicable for a wide range of applications within the Medical Furniture Desk and Industry areas Yet LINAK cannot know all the conditions under which LINAK products will be installed used and operated as each individual application is unique The suitability and functionality of the LINAK product and its performance under varying conditions application vibration load humidity temperature frequency etc can only be verified by testing and s2. for 3 sec While the S is displayed touch the memory button 1 2 or 3 The display will acknowledge by showing S1 S2 or S3 for 1 sec To abort a store sequence press the A or v button while the S is flashing or wait the 3 seconds until the display automatically returns to show the height of the desk Drive to a stored position Press memory button 1 2 or 3 and the system will start driving to the desired memory position Keep the button activated until the position is reached The display will count the height as it is driving to the memory position Customising the DPT digital display Adjust the display to show the correct height The DPT will show 68 cm or 24 5 inches as the height of the desk as the default setting It may be necessary to adjust the displayed height due to different thicknesses of desktops etc when the DPT is delivered from the factory To adjust the display touch the S button and the A or v button at the same time until the display shows the actual height of the desk Changing between cm and inches Touch the S button for approximately 4 seconds and the unit of measurement will change on the display The default setting depends on the type chosen Error Codes The DPT has capability of displaying error codes for diagnostic feedback Below are possible feedback errors which can be displayed by the DPT The error codes will only be displayed when a button is touched in unlocked mode The d
3. 2 or 3 in the display depending on chosen position Memory drive small buttons with dots Press one of the memory buttons and the system will start driving to the pre programmed memory position Keep the button pressed until the position is reached Display function Shows the actual height in either cm or inch Other functions Adjusting initial height It may be necessary to adjust the displayed height due to different thicknesses of desktops etc The DPF1C will as standard either show 68 cm or 24 5 inch as the default desk height Procedure Press A and V keys at the same time and keep them pressed for 5 seconds This allows the initial height to be adjusted Until the initial height can be adjusted the display will show three minuses hereafter the display will revert to showing the height The height can then be adjusted by either A or V until til desired height has been reached The system will return to normal operation and give a short blink after 5 seconds of inactivity on the keys The feature can be disabled via configuration in which case pressing the A and V keys at the same time will be considered an illegal keypress Switch between cm and inch Switching between cm and inch can only be done via the DPF1C configurator Adjusting the light intensity of the LED display Possible settings are Off 6 12 19 25 37 50 75 and 100 The adjustment can only be done via the DPF1C configurator Ad
4. ILSA S A de C V Phone 52 55 5388 3960 Fax 52 55 5388 3966 E mail linak ilsamexico com www ilsamexico com PERU PERCY MARTIN DEL AGUILA UBILLUS Phone 51 99 883 9879 RUSSIAN FEDERATION 000 FAM Phone 7 812 3319333 Fax 7 812 3271454 E mail purchase fam drive ru www fam drive ru SINGAPORE SERVO DYNAMICS PTE Ltd Phone 65 6844 0288 Fax 65 6844 0070 E mail servodynamics servo com sg Www servo com sg SOUTH AFRICA Industrial Specialised Applications CC Phone 27 11 312 2292 or 27 11 2077600 Fax 27 11 315 6999 E mail gartht isagroup co za www isaza co za SOUTH KOREA UNITEK ENG Phone 82 2 567 0888 Fax 82 2 3453 1177 E mail unitekeng unitekeng co kr www unitekeng co kr UNITED ARAB EMIRATES Mechatronics Phone 971 4 267 4311 Fax 971 4 267 4312 E mail mechtron emirates net ae www mechatronics ae For contact details on other countries please visit www linak com or contact LINAK INTERNATIONAL Fax 45 74 45 90 10 E mail info linak com www linak com Terms of use The user is responsible for determining the suitability of LINAK products for specific application LINAK takes great care in providing accurate and up to date information on its products However due to continuous development in order to improve its products LINAK products are subject to frequent modifications and changes without prior notice Therefore LINAK cannot guarantee the correc
5. a memory position Example Action Display view If only one desk is connected go to point 4 1 Press 3 Press 4 Press O i or until the wanted user is shown in the display 5 Press A or W until the wanted height is obtained 6 Press and then or 2 Press i O or Q until the wanted desk is shown in the display 1 8 Desk I User Position II The position is now stored in the control box To store a new memory position on the same desk go through points 3 to 6 again If the buttons are not activated for 15 sec the clock function will appear in the display 23 Switch to a stored memory position Quick setup On the back of the WDP you will find a quick guide for storing a memory position Example Action Display view 1 Press 2 Press or until the wanted user is shown in the display 3 Press and hold O or ow all desks have reached their memory position Desk I User III name Flashing Desk User III Position Position is flashing digits counting from 117 to 88 When the desk has reached the new height position it will stop flashing The display will show the height of the moving desk for about 15 sec If the buttons are not activated for 15 sec the clock function will appear in the display 24 Disposal of LINAK s products As LINAK s customers often ask us how
6. are always ready to help you LINAK provides a warranty on all its products This warranty however is subject to correct use in accordance with the specifications maintenance being done correctly and any repairs being carried out at a service centre which is authorised to repair LINAK products Changes in installation and use of LINAK systems can affect their operation and durability Changes must therefore only be made by agreement with LINAK A S and are made at your own risk LINAK A S Safety instructions A Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons Moreover children must be under surveillance to ensure that they do not play with the product ate It is important for everyone who is to connect install or use the systems to s have the necessary information and access to this User Manual E If there is visible
7. damage to the product it must not be installed ate The appliance is not intended for use by young children or infirm persons w without supervision ate Young children should be supervised to ensure that they do not play with the Sag appliance Repairs In order to avoid the risk of malfunction all DESKLINE repairs must only be carried out by authorised LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Lifting units under warranty must also be returned to authorised LINAK workshops Warning If any of the DESKLINE products are opened there will be a risk of subsequent malfunction Warning The DESKLINE systems are not resistant to cutting oil CE LINAK WE IMPROVE YOUR LIFE DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY LINAK A S Smedeveenget 8 DK 6430 Nordborg Name and address of the person authorized to compile the relevant technical documentation John Kling Group Headquarters Guderup DK 6430 Nordborg email jkI linak com Herewith declares that LINAK Actuators and Actuator Systems comply with the following parts of the Machinery Directive 2006 42 EC ANNEX I Essential health and safety requirements relating to the design and construction of machinery 1 5 1 Electricity supply Directive 2006 95 EC on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits 1 5 10 Radi
8. industrial environments Date 2009 04 03 Signature gt Dn John Kling 31 FACTORIES CHINA LINAK Shenzhen Actuator Systems Ltd Phone 86 755 8610 6656 Fax 86 755 8610 6990 E mail sales linak cn www linak cn DENMARK LINAK A S Group Headquarters Guderup Phone 45 73 15 15 15 Fax 45 74 45 80 48 Fax Sales 45 73 15 16 13 E mail info linak com www linak com SLOVAKIA LINAK Slovakia s r o Phone 421 517563 414 Fax 421 517563 410 E mail jp linak sk www linak com USA LINAK U S Inc North and South American Headquarters Phone 1 502 253 5595 Fax 1 502 253 5596 E mail info linak us com www linak us com SUBSIDIARIES AUSTRALIA LINAK Australia Pty Ltd Phone 61 3 8796 9777 Fax 61 3 8796 9778 E mail sales linak com au www linak com au AUSTRIA LINAK GmbH Austria Phone 43 0 2266 61 9 62 Fax 43 0 2266 63 2 99 E mail info linak de www linak at BELGIUM amp LUXEMBOURG LINAK Actuator Systems NV SA Phone 32 0 9 230 01 09 Fax 32 0 9 230 88 80 E mail info linak be www linak be BRAZIL LINAK DO BRASIL COMERCIO DE ATUADORES LTDA Phone 55 11 2832 7070 Fax 55 11 2832 7060 E mail info linak com br www linak com br CANADA LINAK Canada Inc Phone 1 502 253 5595 Fax 1 905 821 4281 E mail info linak ca www linak ca CZECH REPUBLIC LINAK C amp S S R O Phone 420581741814 Fax 420581702452 E mail p
9. is fixed Drawings of the mounting brackets Article number 914759 Article number 914757 Ta Article number 914760 Article number 914785 l 2 Operation of the DPT For safety reasons the DPT has a locking function i If the DPT is locked only a bar is lightning in the display To unlock the control press S for 1 sec When the DPT is unlocked the height will be shown in the display Now the DPT is active for 2 5 seconds When pressing one of the keys you can do your adjustment Hereafter the DPT will be active for 5 seconds but when there are no activations made within the mentioned time slot the DPT will go in to locking mode again Also if you press S for unlocking too long the DPT will unlock but immediately lock again The Touch Desk Panel is used to operate the DESKLINE systems The DPT is divided into parallel and memory drive The two arrow buttons are used for parallel drive and the last four buttons for memory drive Desk up Desk down Store memory e Memory 1 Memory 2 WIN Memory 3 Normal operation To run the desk up or down press the or v button and keep it pressed until the desk reaches the desired height The display will count the height as the table is moving and will continually show the height of the desk after stopping Storing a memory position Touch the S button and the display will flash S
10. system reaches end position M version DPF1M Desk Panel The DPF is divided into parallel and memory drive The two arrow buttons are used for parallel drive and the last four buttons for memory drive storing memory Parallel up 93 25 V Parallel down S Store memory e Memory 1 ee Memory 2 eee Memory 3 Parallel drive AV The arrow buttons start parallel drive The function is only activated when holding the button down Store memory e Press S button e Within two seconds press one of the small buttons with dots and the position will be stored at this button Memory drive small buttons with dots Press one of the memory buttons and the system will start driving to the pre programed memory position Keep the button pressed until the position is reached Operation of the DPF1C IDPF1C Desk Panel Parallel up V Parallel down S Store memory e Memory 1 ee Memory 2 eee Memory 3 Up and down AV Just activate either the up or down button for parallel drive and the system will drive until the button is released again or the system reaches end position Memory The four small buttons are used for memory drive storing memory Store memory e Press S button the display will flash for 2 seconds e Within these two seconds press one of the small buttons with dots and the position will be stored at this button e The panel will acknowledge by showing 1
11. DESKLINE IMPROVING ERGONOMICS Controls Handsets Li NAK To learn more about LINAK please visit OM WE IMPROVE YOUR LIFE Contents Preface Safety instructions Repairs Manufacturer s declaration Daou Misc on the DESKLINE system Warranty Maintenance Mounting guidelines for DPA DPB Operation of the DP1 Operation of the DP1C Operation of the DPF Operation of the DPF1C Mounting of all DPF verions Operation of the DPT Mounting of the DP1T Operation of the WDPL Disposal of LINAK s products Labels Drawing appendix Addresses Preface We are delighted that you have chosen a product from LINAK A S LINAK systems are high tech products based on many years of experience in the manufacture and development of actuators electronic control boxes controls and chargers We are also constantly improving our products to meet customer requirements This User Manual will tell you how to install use and maintain your LINAK DESKLINE products We are sure that the DESKLINE products will give you many years of problem free operation Before our products leave the factory they undergo full function and quality testing Should you nevertheless experience problems with your systems you are always welcome to contact our service departments or service centres LINAK subsidiaries and distributors all over the world have authorised service centres which
12. ation 1 5 11 External radiation Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility The relevant technical documentation is compiled in accordance with part B of Annex VII and that this documentation or part hereof will be transmitted by post or electronically to a reasoned request by the national authorities This partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of this Directive where appropriate Date 2010 01 01 Signature hu Chr John Kling Certification and Regulatory Affairs Misc on the DESKLINE system Warranty There is a 36 months warranty on the DESKLINE products Controls Hand controls against manufacturing faults from the production date of the individual products see label LINAK A S warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with Furthermore the system must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid For further details please see LINAK A S ordinary conditions of sale Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as fixing po
13. desk up or down press the UP or DOWN button and keep it pressed until the desk reaches the desired height The display will count up or down while running and after stop it will continually show the current height of the desk Changing between cm and inches Keep the S button pressed for approx 4 sec and the reading will change from the current setting The default setting depends on the type chosen Store a memory position When pressing the store button the display will flash S for 3 sec Within the 3 sec press memory button 1 2 or 3 The display will acknowledge by showing S1 S2 or S3 for 1 sec To abort a store sequence press the UP or DOWN button while the S is flashing or wait the 3 sec until the display automatically returns to show the height of the desk Drive to a stored position Version with GO memory Press memory button 1 2 or 3 The display will flash GO1 GO2 or G03 for 3 sec Within the 3 sec press the UP or DOWN button and keep it pressed until the desk stops in the stored position Both the Up and the Down button will activate memory drive Although e g the memory position is higher than the actual height it will drive upwards when you press the Down button While running to a memory position the display will show GO1 GO2 or GO3 and when it stops in the stored position the height of the desk will be shown Releasing the UP or DOWN button will abort the memory drive Th
14. e display will show the height of the desk Version with standard memory Press memory button 1 2 or 3 and the system will start driving to the wanted memory position Keep the button pressed until the position is reached The display will show the actual height during the memory run Adjust the display to show the correct height It may be necessary to adjust the display due to different thicknesses of desktops etc when the DP is delivered from the factory The DP will show 68 cm or 24 5 inches default setting height of the desk At the same time press the Store button and step UP or DOWN until the display shows the correct height Adjusting the light intensity of the LED display Possible light settings are 0 off 25 25 50 50 75 75 100 100 Adjustment procedure Press the 1 button and at the same time either desk up or desk down this will adjust the light intensity Initial press will show the current setting Keep the 1 button pressed during the whole sequence while adjusting up or down Keep a button pressed for more than 800 msec then the button will auto repeat every 100 msec Releasing all buttons stores the new setting Adjusting the light timeout Possible light timeouts are 0 15 sec and off Adjustment procedure Press the 3 button and at the same time either desk up or desk down this will adjust the light timeout Initial press will show the current setti
15. e product is IP30 the customers can be sure that fluids dust will not enter the product The front itself is closed by the acrylic plate s adhesive foil 6 Cable release is specified for max 5 kg 7 Remember to remove the protection foil Frame SECTION A A L i Countersink Min 5 45 SECTION A A Operation of the WDPL The batteries Wired WDPL Install 3 x 1 5 V batteries type AA MOE The batteries are used as a backup of the clock function if the CBD is disconnected from the mains Figure 9 When the batteries are mounted the display will show the clock function in hh mm The clock has to be adjusted See adjusting the clock on page 22 Low battery Change batteries at weak contrast in the display or when the display shows strange symbols misinformation This does not influence the function of the WDPL it is exclusively a sign that the batteries are to be replaced The WDPL will also work without batteries because it will be powered by the control box The WDPL will also work on a CBD4 CBD5 with mains cut off The clock will only be shown if you have battery backup The cable from the WDPL is connected to the control box under your table Control box Wired WDPL WDP fitting for desk SS Figure 11 Flashing when activated IN Error Squeeze Store 4 US cl
16. h local recycling system Please do not throw used or leaking batteries in normal household waste or in nature This will cause damage to the enviroment How to deal with leaking batteries Leaking batteries should be disposed as described above If leaking batteries are discovered in the product the batteries must be removed at once to minimise damage to the product If leaking batteries are left in the product it become defective It is recommended to use plastic gloves when handling leaking batteries The contents of a leaking batteries can cause chemical burns and respiratory irritation If exposed to the contents of a leaking battery please wash with soap and water If irritation persists please seek medical attention In case of eye contact please flush eyes thoroughly with water for 15 minutes and seek medical attention gt Label DPA The label is printed directly on the DPA Label for DPB The label is printed directly on the DPB DPBKOE PO 299218 T A O DPBK06 P O 299218 X Label for DPF1C Label for DP Label for DPF Item DP1000 000001 Date 2006 05 09 X P O 123456 0000 c ev rb xered serne A Label for DPT Label for WDPL WE IMPROVE YOUR LIFE Item WDPL1000 000001 1P40 Date 2006 05 09 P O 123456 0000 S W PIN 0077006 Ver B1 11 E DENMARK 26 DRAWING APPENDIX DESKLINE DPA
17. hall ultimately be the responsibility of the LINAK customer using any LINAK product LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question 30 DECLARATION OF CONFORMITY LINAK A S Smedeveenget 8 DK 6430 Nordborg hereby declares that LINAK Actuator System composed of Control Box s CBD4 CBD5 And Linear Actuator s 31xxxH xxxxx50S DB4 DB5 DB6 DB7 DBO and or Lifting Column s DL2 DL4 DL5 DL6 DL7 DL8 DL9 DL10 DL11 And Desk Panel s DP1C DP1K DP1T DPB DPF DPBK DP1L DP1V DPAK DPH1K WDPL1 complies with the EMC Directive 2004 108 EC according to following standards EN 61000 4 2 1995 A1 A2 EN 61000 4 3 2006 EN 61000 4 4 2004 EN 55022 1998 A2 Class B and complies with Low Voltage Directive 2006 95 EC according to the standard EN 60335 1 2002 A1 A11 A12 A2 Household and similar electrical appliances Safety Part 1 General requirements Additional information The system does also comply with the standards DS EN 61000 6 1 2002 Electromagnetic compatibility EMC Part 6 1 Generic standards Immunity for residential commercial and light industrial environments DS EN 61000 6 3 2002 Electromagnetic compatibility EMC Part 6 3 Generic standards Emission standard for residential commercial and light
18. ints J The cleaners and disinfectants must not be highly alkaline or acidic Ws pH value 6 8 ate The mounting screws on the DP DPA or DPB must be fastened with a max ma torque of 1 Nm Mounting guidelines for DPA DPB The DPA DPB can be mounted on the desktop so that the keys are either facing upwards or outwards Alternatively the DPA can be mounted flat under the desktop with the keys facing downwards Operation of the DPA DPB in connection with DESKLINE systems not CBD2N The Desk Panel is used to operate the DESKLINE system The two arrow buttons are used for parallel drive Parallel drive AV The arrow buttons start parallel drive The function is only activated when holding the button down ate The mounting screws on the DP DPA or DPB must be fastened with a max ay torque of 1 Nm Operation of the DP1 The Desk Panel is used to operate the DESKLINE system DPA Desk Panel The DP is available in a number of versions DP1K DP1L DP1U DP1V DPF1C DPF1K for single parallel drive without memory and DP1U DPF1M for single parallel drive with memory 3 memory positions The two arrow buttons are used for single parallel drive and the last four buttons for memory drive 4 Desk up tL Desk down DP1K Desk Panel S Store memory U User memory Only 1 Memory 1 DP1N DP1L Desk Panel 2 Memory 2 3 Memory 3 EW Single para
19. isplay will blink while showing the error E16 overrules any other error since the detection is registered only in the display and no message is sent to the control box For detailed error description and codes please see the appropriate CBD software description Error no Description E01 The desk has an unknown position and needs to be initialised E02 Overload in upwards direction has occurred E03 Overload in downwards direction has occurred E16 Illegal keys are pressed Mounting of the DP1T The hole in the tabletop has to be made according to the drawing The DPT is mounted in the hole and the two screws on the backside are fastened with a maximum torque of 40 Ncm If you do not have a torque screw driver please tighten gently and not more until you can feel a slight resistance Do not use electrical tool Please note l 1 Mounting the DPT into the tabletop should be done at the end user so the IE product will not be exposed to any stress which can destroy the product when transported 2 For countersink versions the technician must ensure that the acrylic plate is not put under pressure which will push the acrylic plate out of place 3 The screws which are delivered with the product must be used If they have gone lost there should not be chosen new screws which are longer than 12 mm otherwise top and bottom will disconnect 4 If the product has visible damages it should not be mounted 5 Th
20. justing the light timeout Possible settings are 0 15 seconds and Off The adjustment can only be done via the DPF1C configurator Error codes Below please find the possible error codes which can be displayed The error codes will only be displayed when a button is pressed The display will blink while showing the error code The E16 error will overrule any other errors as the detection is registered only in the display and no message is send to the control box Error code Description E01 The desk has a unknown position and needs to be initialised E02 Overload in upwards direction has occurred E03 Overload in downwards direction has occurred E16 Illegal keys are pressed Mounting of all DPF versions The DPF must be mounted via a mounting bracket The mounting bracket comes in 4 different versions depending on how the panel should be mounted Below are some examples on ways to mount Example 1 Article number 914759 Example 2 Article number 914757 The panel is mounted with a 90 The panel is mounted with a 90 bracket bracket and placed close to the tabletop and place with a distance to the tabletop Example 3 Article number 914760 Example 4 Article number 914785 The panel is mounted with a 45 The panel is mounted with a 45 bracket bracket and placed at the edge of the and placed on a tabletop with angled front tabletop To mount the panel Just click the panel into the bracket and it
21. llel drive PRINS DOSE Pane The arrow buttons start the DL4 DB4 The function is gt aT only activated when holding down the button Jone oE Store memory S DP1U Desk Panel e Push S N e Within two sec push either 3 ror Choice of user U only DP1N DP1V Desk Panel Two persons can store 2 memory positions each Select user_1 or user 2 e Push U e Within two sec push either 1 or 2 Store memory S e Push S e Within two sec push either _1 or 2 Memory drive 2113 Memory 1 2 and 3 start a memory drive the channel s drive to a preprogrammed position The mounting screws on the DP DPA or DPB must be fastened with a max w torque of 1 Nm Operation of the DP1C The DP1C cannot be used on the CBD4 with mains cut off Description The DP1C is equipped with display and memory and is compatible with CBD4 Advanced software 077402 ver 1 66 or later The DP1 is only available as a 1 channel version for operation of the parallel channels up and down The actual height of the desk is shown in the display The display is of the LED type with a yellow light and 10 mm high digits 4 gt Desk up J Desk down S 1 Store memory Memory 1 Memory 2 2 3 Memory 3 Normal operation To run the
22. ng Keep the 3 button pressed during the whole sequence while adjusting up or down Keep a button pressed for more than 800 msec then the button will auto repeat every 100 msec Releasing all buttons stores the new setting Errors Below please find the possible errors that can be displayed The errors will only be displayed when a button is pressed The display blinks while showing the error E16 overrules any other error as the detection is registered only in the display and no message is sent to the control box Diagnostic errors The CBD4 version 1 86 or later can send up to 6 different diagnostic error codes at the same time The diagnostic error codes will overrule error states except E16 Diagnostic errors will only appear as long as the button is pressed The display will blink EXX and will toggle through the diagnostic errors and send them to the LINBUS in the CBD For detailed error description and codes please see the appropriate CBD software description Only working with DP1C from production date 1 february 2006 and onwards Error no Description E01 The desk has an unknown position and needs to be initialised E02 Overload upwards has occurred E03 Overload downwards has occurred E16 Illegal keys pressed Operation of the DPF K version DPF1K Desk Panel Just activate either the up or down button for parallel drive and the system will drive until the button is released again or the
23. ock m AM mode PM BB N 4 digits for height pa n ml Desk III User III Position III and clock mode Display layout WDPL Inch sign Active in clock and height mode 20 Calibrating the WDPL For the WDPL to function correctly you have to calibrate your system This has to be done before using the WDPL You only have to do this once Action Display view 1 Switch between cm and inch Press and hold and then press 68 Desk User I 2 Measure the height from desk to floor If only one desk is connected go to point 4 68 w Press es and then press Q or i to select desk Desk User I If only one desk is connected it is not possible to select Desk II or Ill 4 Press and hold and then press Ne W to adjust the height in the display Example The display will switch from e g 68 to 69 70 71 etc when is pressed and held and then is pressed and e g 68 to 67 66 etc when is pressed and held and then Ww is pressed 5 When the wanted height is shown in the display press and hold ion and then os The reference height of the desk will now be stored in the control box When the reference height is stored the digits will be switched off for 1 sec and Desk User back on again If the buttons are not activated for 15 sec the clock function will appear in the display It is not neces
24. onizil linak cz www linak cz DENMARK LINAK DANMARK A S Phone 45 86 80 36 11 Fax 45 86 82 90 51 E mail linak linak silkeborg dk www linak dk FINLAND LINAK OY Phone 358 10 841 8700 Fax 358 10 841 8729 E mail linak linak fi www linak fi FRANCE LINAK FRANCE E U R L Phone 33 0 2 4136 3434 Fax 33 0 2 4136 3500 E mail linak linak fr www linak fr GERMANY LINAK GmbH Phone 49 6043 9655 0 Fax 49 6043 9655 60 E mail info linak de www linak de INDIA LINAK A S Asian Representative Office Phone 91 120 4797013 E mail info linak in www linak in IRELAND LINAK UK Limited Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail sales linak co uk www linak co uk ITALY LINAK ITALIA S r l Phone 39 02 48 46 33 66 Fax 39 02 48 46 82 52 E mail info linak it www linak it JAPAN LINAK K K Phone 81 45 533 0802 Fax 81 45 533 0803 E mail linak linak jp www linak jp MALAYSIA LINAK A S Asian Representative Office Phone 60 4 210 6500 Fax 60 4 226 8901 E mail info linak asia com www linak asia com NETHERLANDS LINAK Actuator Systems B V Phone 31 76 5 42 44 40 Fax 31 76 5 42 61 10 E mail info linak nl www linak nl NEW ZEALAND LINAK New Zealand Ltd Phone 64 9580 2071 Fax 64 9580 2072 E mail nzsales linak com au www linak co nz NORWAY LINAK Norge AS Phone 47 32 82 90 90 Fax 47 32 82 90 98 E mail info linak no ww
25. our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion Guidance We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or combustion For example waste can be sorted into metals plastics cable scrap combustible material and recoverable resources Some of these main groups can be further divided into subgroups e g metal can be divided into steel aluminium copper and plastic can be divided into ABS PA PE PP As an example the table below breaks down the different components in LINAK products to various recycling groups Product Components Recycling group Handset Plastic housing Plastic recycling or combustion Control Cable Cable scrap or combustion PCB board Electronics scrap By now almost all our casted plastic parts are supplied with an interior code for plastic type and fibre contents if any Main groups of disposal Product main Metal Cable Electronics Plastic recycling Comments groups Scrap scrap scrap or combustion DPXX X X X WDPL X X X Disposal of batteries Details regarding safe disposal of used and leaking batteries Batteries should be disposed in accordance with appropriate federal state and local regulations LINAK recommends that used or leaking batteries are disposed throug
26. sary to repeat the calibration when changing batteries 21 Adjusting the clock Example Action Display view 1 Press the clock button using a ball pen 24hr mode European time mode is default can be changed to 12hr mode hr US time mode i Flashing Changing time mode press AN or y jahe Flashing Press the clock button again to confirm time mode using a ball pen 2 Press Ne We adjust hh 3 Press the clock button again to confirm hh 4 Press A or We adjust mm 5 Press the clock button again to confirm mm a x a a 2 3 a Switches to PM if hh gt 11 mm is flashing The clock is now activated Troubleshooting WDPL If errors occur the error code appears in the display The error segment flashes 1 Hz Error Description of the error Troubleshooting code E 01 Position lost Initialise E 02 Overload in upward direction Remove heavy objects from the desk E 03 Overload in downward direction Remove objects that prevent downwards operation E 16 Illegal push on key Release all buttons and activate valid button button combination 22 Store a memory position 3 users can store 3 memory posistions each The connected desks max 3 are to be adjusted individually one at a time Quick setup On the back of the WDP you will find a quick guide for storing
27. t and actual status of said information on its products While LINAK uses its best efforts to fulfil orders LINAK cannot for the same reasons as mentioned above guarantee the availability of any particular product Therefore LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK All sales are subject to the Standard Terms of Sale and Delivery for LINAK For a copy hereof please contact LINAK LINAK amp LINAK A S reserve the right to make technical alterations Copyright LINAK 2010 10 MA M9 02 350 A WE IMPROVE YOUR LIFE
28. w linak no POLAND LINAK Polska Phone 48 22 500 28 74 Fax 48 22 500 28 75 E mail dkreh linak dk www linak pl SPAIN LINAK Actuadores S L u Phone 34 93 588 27 77 Fax 34 93 588 27 85 E mail linakact linak es www linak es SWEDEN LINAK Scandinavia AB Phone 46 8 732 20 00 Fax 46 8 732 20 50 E mail info linak se www linak se SWITZERLAND LINAK AG Phone 41 43 388 31 88 Fax 41 43 388 31 87 E mail info linak ch www linak ch TAIWAN LINAK A S Taiwan Representative Office Phone 886 2 250 80296 Fax 886 2 2508 3604 E mail info linak com tw www linak com tw TURKEY LINAK A S Turkey Representative Office Phone 90 312 4726338 59 Fax 90 312 4726635 E mail vozen linak com tr www linak com tr UNITED KINGDOM LINAK UK Limited Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail sales linak co uk www linak co uk DISTRIBUTORS ARGENTINA NOVOTEC ARGENTINA SRL Phone 54 11 4303 8900 89 Fax 54 11 4032 0184 E mail info novotecargentina com www novotecargentina com COLOMBIA MEM Ltda Phone 57 1 334 7666 Fax 57 1 282 1684 E mail servicioalcliente memltda com co www memltda com co INDONESIA PT HIMALAYA EVEREST JAYA Phone 6 221 544 8956 65 Fax 6 221 619 4658 1925 E mail hejplastic div centrin net id www hej co id IRAN Bod Inc Phone 98 2188998635 6 Fax 98 2188954481 E mail info bod ir www bod ir MEXICO
Download Pdf Manuals
Related Search