Manual - Extech Instruments
Contents
1. POWER BUTTON and AUTO POWER OFF FEATURE 1 Use the POWER button to turn the unit ON or OFF When the unit is powered up a short self test will ensue after which the display will stabilize This meter can either be powered by one 9V battery or an AC adapter When the battery symbol appears on the LCD display replace the battery as soon as possible Low battery power may cause inaccurate readings and erratic meter operation 4 This instrument is equipped with Auto Power OFF which turns the meter off after 10 minutes of inactivity To override this feature press and hold the MODE button until the display shows nft P auto power off de activated or At F auto power off activated FUNCTION SLIDE SWITCH Slide the Function switch on the side of the meter to the desired function Voltage or Current MODE Press the MODE button to select either SOURCE output or MEASURE input UNIT BUTTON Press the UNIT button to select 1 Voltage mode mV or V in source 2 Current mode mA or in source or measure A V OUTPUT ADJUST BUTTONS Press the A YW buttons to increase or decrease the output voltage or current value in the source mode 1 Press the A button once to increase the value in one digit steps 2 Press and hold the A button to increase the value in 10 digit steps 3 Press and hold the A button gt 2 sec and then press the W to increase the value in 100 digit steps 4 To decrease the value use the V button as described above2. User s Guide EXTECH INSTRUMENTS Model 412355A Current Voltage Calibrator Introduction Congratulations on your purchase of the Extech Current Voltage Calibrator The Model 412355A can measure and source current and voltage The Oyster Series meters have a convenient flip up display with neck strap for hands free operation This meter is shipped fully tested and calibrated and with proper use will provide years of reliable service Meter Description LCD display POWER button UP and DOWN buttons MODE button UNIT button MEM and ZERO button Input Output mini connector AC adaptor jack oe oO NP a FON Battery compartment gt gt Neck strap holders Function switch Battery Replacement When the LOW BAT message appears on the LCD replace the 9V battery as soon as possible 1 Open the calibrator s lid as far as possible 2 Open the battery compartment using a coin at the arrow indicator 3 Replace the battery and close the cover You as the end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle 2 412355A EU EN v3 3 07 13 Operation
3. ZERO BUTTON The ZERO button manually zeros the display in the MEASURE mode 1 Set the meter to the MEASURE mode 2 Short the input jack 3 Press and release the ZERO button 3 412355A EU EN v3 3 07 13 MEM BUTTON The memory feature provides 5 user settable source values for stepped calibration outputs The feature is available for Voltage mA and in the SOURCE mode The memory values are stored in nonvolatile memory and are not erased when power is turned off Sourcing from the stored memory values 1 Select the Source mode 2 Press the MEM button The M1 icon memory location 1 will appear in the display and the value stored in that location will be displayed and sourced 3 Repeated pressing of the MEM button will step through the 5 memory locations NOTE The SOURCE icon will blink when the output value has not reached a stable level The common cause for the SOURCE icon to remain blinking is that the load impedance is too high in the current mode or too low in the voltage mode Storing values into memory 1 Select and display a memory location M1 to M5 2 Press the A W buttons to adjust the display to the desired source value 3 Press and hold the MEM button for gt 2 seconds The displayed value will be stored into the displayed memory location Default memory values Five common source values are permanently programmed in memory as the default values These values can be replaced by user
4. ion Cable to the device or circuit under test Use the A W buttons to select the desired output value Use the LCD display to verify the output level Alternatively use the stored calibration values in memory as described in the MEM button section For the 25 to 125 output range the output is 0 to 24mA 25 0 25 50 75 100 125 Display mA OmA 4mA 8mA 12mA 16mA 20mA 24mA output NOTE The SOURCE icon will blink when the output value has not reached a stable level The common cause for the SOURCE icon to remain blinking is that the load impedance is too high in the current mode or too low in the voltage mode 5 412355A EU EN v3 3 07 13 Specifications General Specifications Display Meter Power Auto Power OFF Current output capability Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Altitude Dimensions Weight Accessories Supplied Range Specifications Measure 9999 count LCD 9 volt battery or 9V AC adaptor Meter automatically powers off after 10 minutes of inactivity 24mA at 1000 ohms 5 C to 40 C 41 F to 104 F 20 C to 60 C 4 F to 140 F Max 80 up to 31 C 87 F decreasing linearly to 50 at 40 C 104 F lt 80 2000meters 7000ft maximum 96 x 118 x 45mm 3 8 x 4 7 x 1 8 folded 340g 12 oz 9V battery AC adaptor and calibration cable with spade
5. lugs Mode Function Accuracy of reading 0 075 1 digit or 3 Source Voltage digits whichever is greater Copyright 2013 FLIR Systems Inc All rights reserved including the right of reproduction in whole or in part in any form ISO 9001 Certified www extech com 6 412355A EU EN v3 3 07 13
6. selected values To reset the meter to the default memory values 1 Turn the meter on and select the SOURCE mode 2 Press and hold the POWER button for gt 4 seconds OFLE will briefly appear in the display and the default values will be stored into memory Default Memory Values M1 M2 M3 M4 M5 mV OmV 500mV 1000mV 1500mV 2000mV V 2V 5V 10V 15V 20V mA 4mA 8mA 12mA 16mA 20mA 0 25 50 75 100 Over range Under range Indication Signals above or below the units ranges will be indicated by HHHH for above and LLLL for below 4 412355A EU EN v3 3 07 13 Measure and Source MEASURE Input In this mode the unit will measure voltage or current BO HOL Be TOO Nn Select Voltage or Current on the Function switch Turn the meter ON Press the MODE button to select MEASURE Press the UNIT button to select mA or if current is selected Connect the Calibration Cable to the meter Connect the Calibration Cable to the device or circuit under test Read the measurement on the LCD display SOURCE Output In this mode the unit will source output voltage or current 1 2 3 4 Select Voltage or Current on the Function switch Turn the meter ON Press the MODE button to select SOURCE Press the UNIT button to select V or mV if voltage is selected or to select mA or if current is selected Connect the Calibration Cable to the meter Connect the Calibrat
Download Pdf Manuals
Related Search