User manual / Technical Information
Contents
1. place that water or chemicals may go into the equipment gt PO If they going into the equipment the circuit may short Then fire or electric shock may occur as the result Other precautions during stora When storing this unit take the following precautions e Store this unit at temperatures from 10 to 50 C and a humidity from 20 to 95 e Do not store this unit in locations directly exposed to steam and in locations where condensation occurs e Do not store this unit in locations where corrosive gases are generated e Do not use this unit in locations subject to vibration e Do not use this unit in locations exposed to excessive dust or debris e Do not leave this unit in unstable or hazardous locations Do not apply excessive shock to this unit and do not drop it e Do not place this unit in locations where the temperature is extremely low or near heaters e Avoid using this unit in locations directly exposed to air flow from an air conditioner or fan e Do not place any object on this unit When moving or transporting this unit When moving or transporting this unit take the following precautions Always use the original carton and packing materials when transporting this unit Our warranty does not cover any damage or breakdown caused during transportation due to use of non specified cartons and packing materials When moving this unit always first disconnect the DC plug from the devic2. Lumitester PD 20 Control Kit Operation manual NC60 1 Carl Roth GmbH Co KG Schoemperlentr 3 5 D 76185 Karlsruhe BOTH Tel 0721 5606 0 Fax 0721 5606 149 www carlroth com Thank you for purchasing the Lumitester PD 20 Control Kit To use this kit safely and correctly read this operation manual carefully and follow the instructions Kikkoman Biochemifa Company Ver 1 0 Table of Contents _ O on DE on OE ae ee IS r a r r a n Oro Oro E O Nea O Please read first List of contents Overview Features List of components Dimensions and part names Operating method Judgment of a measurement result Maintenance Troubleshooting Specification of light source positive rod Specification of a blank tube negative rod Calibration Warranty Reliability Contact o O O O W N 10 12 12 13 14 14 14 15 15 15 1 Please read first This kit is used to check the indicated value of Lumitester PD 20 Please do not use it for the other purposes This operation manual uses following symbols for safe and proper use WARNING indicates a potentially hazardous situations Which if not WARNING avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not CAUTION avoided could result in minor or moderate injury or damage to the gt gt equipment In addition to the above alert symbols and signal word
3. e and then unplug the AC adaptor from the electrical outlet Disposal of this unit When disposing of this unit comply with the laws and regulations in your area WARNING Do not put unit in fire AN And do not burn it t There is risk of explosion or burst inside it s 2 List of contents Light source 1 Blank tube 1 AC power cord AC DC adaptor 1 A plug type 1 AC power cord C plug type 1 e Operation manual 1 e Silica gel 1 3 Overview The check of Lumitester PD 20 operation and the check of sensitivity can be performed by using this kit This kit can generate a stable light by adopting automatic light control using LED 4 Features e Electric method using LED e The fluorescence by a radioactive material is not used e Stable light is generated by automatic light control e Battery exchanging is unnecessary with rechargeable e Charge time is about 30 seconds e Luminescence duration About 15 minutes 5 List of components Name Specification and characteristic Quantity Light source positive rod 1 Blank tube negative rod Typical 0 RLU 1 AC DC adaptor for charge Output DC 5V 3A 1 Power cable for Japan A type 1 Power cable for Europe C type 1 Operation manual Ver 1 0 1 storage Case for transportation and 6 Dimension and part names Jack for charge The body of a light source Labels RLU and term of validity disp
4. ich occurred as a result of use warranty does not cover 15 Reliability Quality and reliability of our products is very important to us However the breakdown occurs in the product including the semiconductor at a certain probability Therefore pay attention to the following item before you use it e Use it safety to cause neither the accident resulting in injury or death nor the fire accident etc A user s equipment may differ from the diagram of this manual or the items mentioned in part about details Please understand the situation beforehand 16 Contact Please tell us the question about directions for use to the following contact my Carl Roth GmbH Co KG Schoemperlentr 3 5 D 76185 Karlsruhe ROTH Tel 0721 5606 0 Fax 0721 5606 149 www carlroth com 15
5. lay etc Luminescence part Hole for degassing 7 Operation method Operate it by following method and notes 7 1 Connect an AC power cord to outlet And connect a DC plug to a jack for charge Hold here and connects with Jack and charge AC power cord AC DC adaptor I De pug wol Cautions Do not give stress to a cord 7 2 Charge for about 30 seconds 30 second or more charge has no problem Additional charge is possible 7 3 Remove a DC plug from a jack for charge And remove an AC power cord from outlet Also remove AC plug of an AC DC adaptor from an AC power socket Hold here and remove from Jack AC DC adaptor DC plug 10 7 4 Start PD 20 Insert a light source into a measurement chamber age y This mark is in front 7 5 Press Enter key of Lumitester PD 20 and measure lt Caution gt Hold this unit vertically while measurement If you set diagonally or horizontally an error may increase In the case of error increases 1 In the case of error increases 2 Holding diagonally Holding horizontally 7 6 Measure a blank tube like 7 4 and 7 5 11 8 Judgment of Measurement Result Results Treatment When it has not improved 1 When RLU is less than There is a possibility Failure of PD 20 80 of a label display that the measurement or a recalibration may be When a RLU display is chamber of PD 20 or required 1000 800 or
6. less the luminescence part Please contact the dealer window of the light Or us source is dirty Clean it off 2 When RLU is over There is a possibility Failure of PD 20 120 of a label display that the measurement or a recalibration may be When a RLU display is chamber of PD 20 is required 1000 1200 or more dirty Please contact the dealer Clean it off Or us 3 When the measured There is a possibility Failure of PD 20 value of a blank tube that the measurement or a recalibration may be over 10RLU chamber of PD 20 is required dirty Please contact the dealer Clean it off or us When PD 20 doesn t display a normal value by 1 or 2 and when it displays a normal value by 3 The possibility of failure of a light source is also suspected Please send to the dealer or us together in repair of PD 20 or the case of recalibration 9 Maintenance 9 1 Maintenance of a light source The surface of the luminescence part is glass If this part is dirty light volume will decrease In such a case wipe with a dry cloth or paper such as tissue paper If this part is heavily dirty wipe with a soft cloth damped with diluted mild detergent solution lt Cautions gt Do not spill liquids reagents nor organic solvents etc over the instrument If any liquid should be spilt on the instrument wipe the liquid off immediately dry the instrument When dirt remains Take the same treatmen
7. nk tube in Lumitester PD 10 Or do not insert to other company products e Do not move this equipment during measurement It may cause an error of measurement e Do not incline this equipment during measurement It may cause a measured value error e Be sure to take out a light source after measurement e Keep this equipment at least 50cm away from the electromagnetic noise source e Do not expose this equipment to liquids reagents and organic solvents That may cause failure discoloration and modification If they are attached wipe off immediately e Use it in the range of temperature 10 30 C and humidity 20 85 e Do not use it at the place where temperature changes violently e Do not use it at a place with sunlight or strong light It may cause an error of measurement e Do not expose it to steam Use it at the place without dewing e Do not expose it to corrosive gas e Use it at a place without vibration e Use it at a place with little dust e Do not put on unstable place or a dangerous place e Do not fall it or give a strong shock e Avoid the place where the wind of an air conditioner hits directly Notes on installation or storage ae While using a light source do not use the chemicals which flammable gas generates Moreover do not keep or install in flammable gas atmosphere In this case there is a risk of a gas explosion occurring inside equipment Do not install or keep it in a
8. s the following warning symbols are used in this manual to designate the degree of hazard and damage that might occur if this product is used incorrectly Mandatory This symbol indicates a mandatory action Prohibited This symbol indicates a prohibited action Electrical shock hazard This symbol indicates a risk of electrical shock Fire hazard This symbol indicates a risk of smoke emission or fire Explosive hazard This symbol indicates a risk of explosion Toxic hazard This symbol indicates a toxic substance risk Corrosion hazard This symbol indicates a risk of corrosion oP Pee OO Handling precautions If an abnormal condition is found A N WARNING PERO When abnormality is observed remove AC power cord from outlet immediately When abnormality is observed such as malfunction burning smell fuming etc there is a danger of fire and burst Make sure that fumes are extinguished and contact the dealer or us Never repair the instrument by yourself as this is very dangerous Precautions during use WARNING PELO Do not use chemicals that may generate flammable gases and do not use in an atmosphere containing flammable gases Doing so may cause gas explosion in this unit Never attempt to remove any cover of this unit or disassemble or repair any part of this product Only our qualified service personnel are allowed to service thi
9. s unit This unit contains high internal voltages so improper handling may cause electrical shock fire or abnormal operation Do not plug or unplug the AC adaptor with wet or moist hands Doing so may cause electrical shock fire or malfunction When using the AC adaptor always connect it to a power source ranging from AC 100V to 240V 50 60H2 Failure to follow this instruction may cause electrical shock or fire or damage this unit Never connect an AC power source to the AC adaptor input and RS 232C terminal Doing so may cause electrical shock fire or malfunction Do not expose this unit to water and do not handle it with wet hands This unit is not water proof so water or moisture may cause electrical shock fire or malfunction CAUTION When thunder has occurred please do not connect an AC DC adaptor to an electric outlet Use an AC DC adaptor only at the time of charge Pull out the AC DC adaptor from an electric outlet and remove it from a light source when you do not use it Do not cover the hole of this side There are two holes of degassing in the side 2l Do not soil the glass of a luminescence part If dirt and a crack are given to glass light volume will change Other cautions When you use this equipment be careful of the following things e This equipment is Lumitester PD 20 exclusive use Do not insert a light source or bla
10. t as the above mentioned maintenance 12 10 Troubleshooting WARNING D ZAA When abnormality is observed remove AC power cord from outlet immediately When abnormality is observed such as malfunction burning smell fuming etc there is a danger of fire and burst Make sure that fumes are extinguished and contact the dealer or us Never repair the instrument by yourself as this is very dangerous 13 11 Specification of a light source positive rod Item Contents Light emitting device Green LED Center wavelength Typ 545nm Half width of spectrum 40nm Typ RLU value It is displayed on the label of a light source Ambient temperature range 10 30 C Ambient humidity range Storage temperature range 20 85 Free from condensation 0 35 C Storage humidity range 20 95 Free from condensation Internal power source Electric double layer capacitor Terminal for charge Outer diameter 5 5mm__Inner diameter 2 14mm Charging current Center plus Input voltage 5 0V MAX 1A After the completion of charge About 2 mA Charge time 30 seconds or more Operating time 15 minute after the completion of charge Dimensions Diameter 12mm_ Length 134 7mm Weight About 20g except AC DC adaptor 12 Specification of a blank tube negative rod Item Contents RLU value Tolerance of a RLU value T
11. yp ORLU Minimum ORLU Maximum 10RLU Dimensions Diameter about p12mm Length about 149 5mm Weight About 10g 13 Calibration This device is factory calibrated with a minimum period of validity as stated on the label The calibration will only be valid if the instructions contained in this document are followed Any non recommended use may compromise this calibration Following the stated period of validity the device can be re calibrated and re labeled with new period of validity for a fee 14 14 Warranty A warranty period of the Lumitester PD 20 control kit is one year from the date of purchase except that it is two years from the date of purchase in member states of EU where EU Directive 1999 44 EC is in effect If any failure is found in the workmanship or materials within this warranty period we will repair or replace the defective parts without charge However the warranty does not cover any of the following cases even if within the warranty period e The product has been misused not following the operation manual It includes for example such case where the failure was caused by the use with an Incorrect AC DC adaptor e The product has been modified e The failure was caused by natural or man made disasters including but not limited to earthquake fire lightning flood and others This warranty is limited to repair or replacement e In the case of damage to the peripheral equipment wh
Download Pdf Manuals
Related Search