manual_GB18, COD18, SD18, WD18
Contents
1. Remote or as a Sensor the difference between these mode is explained below Remote mode When set to Remote mode the detector will act as a remote which means it will always trigger an alarm as soon as a fault is detected The state of the console being Armed or Disarmed will make no difference Sensor mode In Sensor mode the status of the console in which an alarm is triggered will be configurable Default this will only be when the console is armed like for example a motion detector To change this the detector can be configured being an Emergency Sensor then an alarm will be given regardless the state of the console The advantage of the detector set to Sensor mode is that will be possible to execute home automation functions when the detector is triggered E g when a Water detector detects water in your basement you can switch on an appliance module to control a pump The preferred mode can be chosen with the selection switch on the back side of the detector Set the detector to the desired mode sensor or remote and place it in the chosen location The registration process is the same for both the remote and the sensor mode Registering with the SC28 HomeProtector 1 Set the detector to the correct mode being Remote or Sensor 2 Access the menu of the console done by either using the menu UP Oor DOWN button The display now shows ENTER PIN 3 Enter your PIN factory default is 0000 The display is2. ause false alarms Extreme temperatures will affect the sensitivity of the CO amp Smoke Alarm Do not install in areas where the temperature is below 40 degrees Fahrenheit 4 4 Celsius or above 100 degrees Fahrenheit 37 8 Celsius Place the detector away from doors and windows that open to the outside Using the CO amp Smoke Detector Installing the battery Connect a new 9 volt battery to the connector Do not use a rechargeable battery The battery will fit only one way Be sure the battery connector is securely attached Last update 25 07 2008 p g 4 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 Place battery into battery pocket Alarm Every alarm type has its own individual character CO alarms will sound as four short alarm beeps and continuous beeps will sound when smoke is detected In case both are detected simultaneously the smoke pattern alarm will sound One chirp every 30 seconds will be an indication that the battery is low or the unit is malfunctioning In case of a low battery level replace the battery as soon as possible As you install the battery the unit will sound chirp to indicate the battery is installed properly The red LED will flash in conjunction with the alarm beep l e the red LED will flash during a CO alarm a fire alarm and a low battery mode chirp Testing the detector Press the test b
3. centralcasa domotica Technical Sensors GB18 COD18 SD18 WD18 Wireless technical Sensors GB18 wireless Gas Detector COD18 wireless Carbon Monoxide Detector SD18 wireless Smoke Detector WD18 wireless Water Detector Last update 25 07 2008 pag 1 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 GB18 Gas dotectokr AA A AA Installation Instructions a Using the Gas CeteCtOrc cssscccdsccessseesesaces cceeseedesuaceceestecessssesactssadecevessssssteccdscevecssscateccdscetsesseeatencdeusteaseesatensis Carbon Monoxide COD18 amp Smoke detector SDB a Installation instructions Using the CO amp Smoke DeteCtOr es aaa AABANG WD18 Water detector 1111 2 nint tn nunnan ntn nunn EEEa AARAA ER AEEA EEEA AEREE EA AEEA EEEEEEREEER EEA EEEA EER EEE REEE EEEE Installation Instructions 0 0 0 LA Using the Water detector aaa NAA AA ANAN AN ANAN AA ATA tre etre er AA Registering a technical sensor with a compatible security console ssswwwwaaaaaaanaananaaaaananannaaasasaaannnana Registering with the SC28 HomeProtector4 ccccceeeceeeeceeeee eee e eee eeeceaaeee sees eeeeeecaaeeeeeeeeeeeeecaaeeeeeeeeeteeneaaaes Registering with the BS800 HOMeGUAIC ccc ee eectene eee eee e eee a ease eee eeteeeaaaeeeeeeeeeteecaaaaeeeeeeeeteeeaaaeaaaes Last upda
4. cleared and shows a for each number entered 4 When the PIN code has been entered correctly the word INSTALL will show up on the display 5 Press OK 6 Press the TEST button on the Detector The console will beep to confirm The display will either read ZONE 1 SET when sensor mode was set or RMOT 1 SET when remote mode was set A memory space for a sensor is called a zone If you have more than 1 sensor installed they will be shown e g ZONE 2 SET ZONE 3 SET ZONE 30 SET You can choose in which zone you want to install the sensor If you want to install the sensor in zone 3 press 3 on the number pad before executing step 5 It s advisable to write down which zone contains which sensor There is space reserved at the back of this User Manual 7 Repeat step 5 for every Detector you wish to register 8 Press CLEAR to go back to the first menu item Press CLEAR again to quit the menu To confirm this choice press 1 for Yes or 2 for No If you choose Yes you will quit the menu If you choose No you go back to the first menu item Last update 25 07 2008 pag 8 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 Registering with the BS800 HomeGuard 1 Set the detector to the correct mode being Remote or Sensor 2 Access the menu of the console a PIN will be requested 3 Enter your PIN factory default is 0000 You will hear three h
5. igh tones and one low tone as confirmation The green indicator starts flashing 4 Press 1 on the keyboard of the HomeGuard One high tone is given for confirmation 5 Press the test button of the sensor One low tone is given for confirmation 6 Repeat step 1 3 for every Detector you wish to register 7 Press any button on your HomeGuard keyboard to finalise the registration procedure One short low tone is given and the green indicator will stop flashing If successive commands are not entered within a period of 15 seconds the base station returns to normal operation To restart the registration you must start the procedure from step1 NOTE The RF range can be affected by a number of factors including building construction so make sure you test the detector in the desired location using the detector s main test button The detector will sound an alarm and when in range the console will also acknowledge the detector Last update 25 07 2008 pag 9 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt
6. ning of the detector it is recommended to test the detector on a monthly basis The detector can either be checked by using the test button on the side of the detector Technical Specifications Power Source 220V AC Sensitivity 10 LEL Power Consumption 1 7W Operating Temperature 10 50 C Ambient Humidity Less than 95 RH Horn Level 85 Decibels Weight 270g Type Of Gas Sensed LPG Butane Propane used in normal and mini gas bottles Gas from piping system city gas and natural gas Methane Last update 25 07 2008 pag 3 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 Carbon Monoxide COD18 amp Smoke detector SD18 Installation instructions Recommended Installation Locations We recommend the installation of a Carbon Monoxide amp Smoke Combination Detector in the following locations illustrated below For maximum protection we suggest an alarm be installed on each level of a multilevel home including every bedroom hallway finished attic and basement Put an alarm at both ends of a bedroom hallway or large room if the hallway or room is more than 30ft 9 1m long If you have only one alarm ensure it is placed in the hallway outside of the main sleeping area or in the main bedroom Verify the alarm can be heard in all sleeping areas Locate an alarm in every room where someone sleeps
7. r Alarm but the moisture is unable to come into contact with the sensors in the legs of the unit the alarm will not sound and damage could occur The Water detector should be placed so that leaking water will come into contact with the legs immediately The water detector may not be heard The loudness of the alarm in your detector meets or exceeds current standards However if the water detector is placed in the basement it may not be heard on the second floor If the sound is blocked by distance closed doors normal noise such as traffic stereo radio television air conditioning units or other appliances it may not be heard The alarm may not be heard by people that are hard of hearing Water detectors are not substitutes for property insurance The Water Alarm is designed to alert you to potential water damage There is no guarantee expressed or implied that it will prevent water damage Using the Water detector Installing the battery Match the terminals of a 9 volt Alkaline battery do NOT use rechargeable batteries to the connections on the Water Detector When the terminals are properly matched push the other end of the battery gently into the base of the Water Detector When the battery is getting to the end of its useful life the Water Detector will bleep approximately once every minute and the battery should be replaced as soon as possible To remove the battery turn the unit over and gently lift the end of the battery away f
8. rom the terminals and withdraw from he battery compartment The Water Detector will not function and may be damaged if the battery is not correctly installed Alarm operation The Water Detector is designed to detect water that comes in contact with the sensors in its legs A slight dampness will be enough to trigger the sensor The metal sensors in the legs will penetrate into carpeting for better sensitivity Water that does not come in contact with the sensors cannot be detected Testing the detector Correct operation of your Water Detector can be verified by placing it on a damp towel The alarm will sound within 3 seconds When the this does not happen or it takes longer replace the battery and re test If replacing the battery does not Last update 25 07 2008 pag 6 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 fix the problem the unit needs be repaired or replaced immediately This is the only way to ensure that the Water Detector is working properly Technical Specifications Power Source 9V battery Alkaline or Carbon Zink Last update 25 07 2008 pag 7 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 Registering a technical sensor with a compatible security console The detector can be registered in two different modes being either as a
9. te 25 07 2008 pag 2 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 GB18 Gas detector Installation Instructions Recommended Installation Locations Mount the detector on the wall or cabinet about 30cm above the ground for LPG or about 30cm below the ceiling for carbon monoxide gas and natural gas use The ventilation hole should be installed facing downwards General limitations Install the detector securely to avoid impact and drop Prevent dust and oil from entering the detector as this could block the ventilation slots and cause the detector to malfunction Do no install the gas detector near hot humid and oily sources Do not install the gas detector near windows or fans where a gas leak can be quickly dispersed Using the Gas detector Plug the flying lead of the detector into a 230V 50Hz wall socket The equipment needs 3 5 minutes for the sensor to begin functioning The green LED will light up in normal mode Alarm operation When the Gas detector detects an ignitable gas three short alarm beeps will sound at intervals until the ignitable gas has disappeared If the detector is malfunctioning a single alarm beep will sound continuously The red LED will flash in conjunction with the alarm beep I e the red LED will flash during a gas alarm and a low battery mode alarm Testing the Detector To ensure the correct functio
10. utton for several seconds to test the detector s electronics The alarm will sound NOTE Do this weekly to ensure correct functioning Technical Specifications a Power Source 9V battery Alkaline or Carbon Zink a Sensitivity Setting CO 100 50ppm CO concentration SMOKE 1 5 FT OBS a Power consumption Standby lt 100uA Alarm lt 75mA Operating Temperature 5 40 C a Ambient Humidity 20 90 RH a Horn Level 85 Decibels Last update 25 07 2008 p g 5 de 9 Copyright CentralCasa info centralcasa pt www centralcasa pt centralcasa dom tica Technical Sensors GB18 COD18 SD18 WD18 WD18 Water detector Installation Instructions Recommended Installation Locations Place the Water Detector level with all 4 legs flat on the surface to be monitored for water Place a Water Detector in areas where there is a potential for water damage from leakage Suggested areas are a Near or under washing machines dishwashers refrigerators sinks etc Next to your kettle Under a water bed Inthe bathroom where toilets tubs or sinks could overflow Inthe basement where ground water or leaky water lines may cause damage On the floor under potentially leaky pipes General limitations Water detectors will not work without properly installed batteries Test monthly for proper operation Water Detectors will not sense water that does not come in contact with the sensing probes If there is a leak near the Wate
11. with the door closed Mount the alarm on the ceiling in the centre of the room Ceiling mounting is preferred in ordinary residential construction When mounting an alarm on the ceiling locate it at a minimum of 4 10cm from the side wall If installing the alarm on the wall at a minimum of 4 10cm and a maximum of 12 30 5cm below the ceiling see diagram below 4 10cm CEILING MINIMU 4 10cm F INIMU NEVER HERE i h ACCEPABLE f 30 5cm HERE MAXIMUM ZSIDE WALL Where not to mount the detector Do not install in garages kitchens furnace rooms or bathrooms and INSTALL AT LEAST 15 FEET 5m AWAY FROM ANY FUEL BURNING APPLIANCE Do not install within 3ft 0 9m of the following The kitchen door or a bathroom that contains tub or shower forced air ducts used for heating or cooling ceiling or whole house ventilating fans or other high air flow areas Avoid excessively dusty dirty or greasy areas Dust grease or household chemicals contaminate the alarm s sensors causing it to malfunction Do not place the alarm where drapes or other objects can block the sensor Carbon Monoxide and smoke must be able to reach the sensors to accurately detect these conditions Do not install in peaks of vaulted ceiling A frame ceilings or gabled roofs Avoid installing the detector in damp and humid areas Install at least one foot away from fluorescent lights electronic noise may c
Download Pdf Manuals
Related Search