Home

User manual

1. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal noncommercial use of this product and shall not apply to the following damage that occurs in shipment delivery and installation applications and uses for which this product was not intended altered product or serial numbers cosmetic damage or exterior finish accidents abuse neglect fire water lightning or other acts of nature or God use of products equipment systems utilities services parts supplies accessories applications installations repairs external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems incorrect electrical line voltage fluctuations and surges customer adjustments and failure to follow operating instructions maintenance and environmental instructions that are covered and prescribed in the instruction book product removal and reinstallation problems caused by pest infestations This limited warranty does not cover problems resulting from incorrect electric current voltage or supply light bulbs house fuses house wiring cost of a service call for instructions or fixing installation errors SAMSUNG does not warrant uninterrupted or error free operation of the product EXCEPT AS SET FORTH HEREIN THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING BUT NOT LIMITED TO ANY
2. a om w D je 2 Use 4 diameter rigid metal duct Tape all joints including at the dryer Never use lint trapping screws 3 Keep ducts as straight as possible English 29 DV8000J 03170M 01_EN US_150122 indd 29 a 2015 1 23 16 30 00 Installation 4 Clean all old ducts before installing your new dryer Be sure the vent flap opens and closes freely Inspect and clean the exhaust system annually S amp wy Va Don t let a poor exhaust system slow drying by 1 Restricting your dryer with a poor exhaust system 2 Using a plastic thin foil or non metal flexible duct N 30 English DV8000J 03170M 01_EN US_150122 indd 30 a 2015 1 23 16 30 00 3 Using unnecessarily long ducts that have many elbows a a w D je 4 Using crushed or clogged venting or ducts Door reversal If you want to reverse the direction of the door we recommend you call a qualified service technician 1 Unplug the power cord 2 Remove the four hinge screws from the door 3 Remove the door by lifting it English 31 DV8000J 03170M 01_EN US_150122 indd 31 a 2015 1 23 16 30 01 Installation 4 Remove the two screws from the holder lever and then remove the cover holder 5 Assemble the holder lever on the opposite side using the screws that were removed from the holder lever in Step 4
3. 6 Assemble the cover holder on the opposite side Installation 7 Remove the two cover hinges 8 Assemble the two cover hinges on the opposite side NOTE Use a flat head screwdriver to remove the cover holder s cover hinge 9 Remove the 14 screws NOTE Two screws B are longer than the other Screws 32 English DV8000J 03170M 01_EN US_150122 indd 32 a 2015 1 23 16 30 01 10 Remove the holder glass 11 Exchange the positions of A The cover hinge and handle door B The holder hinge and guiderholder glass 12 Remove the door lever and then install it on the opposite side NOTE Refer to the illustrations on the left to aid you in the assembly process a om w D eo 13 Remove the cover hole C 14 Assemble the holder glass and then fasten the 14 screws that you removed instep 9 15 Attach the cover hole NOTE A spare cover hole is in the assy manual English 33 DV8000J 03170M 01_EN US_150122 indd 33 a 2015 1 23 16 30 02 Installation 16 Install the door on the frame front and then fasten the 4 screws that you removed in step 2 NOTE Check the positions of the screws you installed in the hinge door S Ww Z Va 34 English DV8000J 03170M 01_EN US_15012
4. D Securely tighten the gas line fitting over the threads E Turn on the gas supply Check all gas connections for leaks Using a soap solution If bubbles appear tighten the connections and recheck DO NOT use an open flame to check for gas leaks F Go to Step 6 a om w D eo English 21 DV8000J 03170M 01_EN US_150122 indd 21 a 2015 1 23 16 29 57 Installation 6 Review the Electrical requirements section then follow the 3 Wire system connection instructions Step 7 or 4 Wire system instructions Step 8 below 7 Three Wire system instructions A External ground connector B Neutral grounding wire white C Center silver colored terminal block screw D Neutral wire white or center wire E 34 1 9 cm UL listed strain relief a Loosen or remove the center terminal block screw b Connect the neutral wire white or center wire of the power cord to the center silver colored terminal screw of the terminal block Tighten screw c Connect the other wires to outer terminal block screws Tighten screws d Tighten the strain relief screws e Insert the tab of the terminal block cover into your dryer s rear panel slot Secure the cover with a hold down screw e amp wy Va N WARNING If converting from a 4 wire electrical system to a 3 wire you must connect the ground strap to the terminal block support to ground the dryer frame t
5. HEAVY DUTY Use this cycle to get high heat for heavy fabrics such as jeans corduroys or work clothes BEDDING e For bulky items such as blankets sheets and comforters e i f D PERM PRESS e Dry wrinkle free cottons synthetic fabrics Knits and permanent press fabrics automatically gt WOOL e For machine washable and tumble dryable wool only DELICATES e For heat sensitive items at a low drying temperature e For exercise wear and outdoor wear such as sports jerseys training pants water repellent jackets and other performance ACTIVE WEAR clothing Thick fabrics like a zipper or velcro closure of a jacket or training socks may not be completely dried TOWELS e For bath towels and similar items English 41 DV8000J 03170M 01_EN US_150122 indd 41 a 2015 1 23 16 30 04 Operations Manual Dry cycles Cycle Description QUICK DRY e Provides a 30 minute drying cycle e Allows you to select a cycle time in minutes If this cycle is selected the Eco Dry function is enabled by TME DRY default For more information refer to the description of the Eco Dry option AIR FLUFF e Tumbles the load in room temperature air Steam Dry cycles Cycle Description e Best for smoothing out wrinkles and reducing odors from loads consisting of one to four dry items In this cycle a small amount of water is sprayed into the dryer drum after several minutes of
6. NOTE The Smart Care function has been optimized for Galaxy amp iPhone series cannot be supported for some models Download the Samsung Smart Care app into your smart phone from the Android market or Apple App store Search word Samsung Smart Washer Dryer To use Smart Care follow these steps 2015 1 23 16 30 04 1 Press Power to turn the dryer on and then press and hold Eco Dry for 3 seconds If you press a button other than Eco Dry after turning the dryer on you will not be able to activate the Smart Care function 2 When the Smart Care function is activated the Smart Care indicator lights up on the display 3 Run the Smart Care app on your smart phone 4 Focus the smart phone s camera on the display panel of the dryer 5 When the smart phone s camera is focused on the display panel of the dryer the panel and information code is automatically recognized and the code type and countermeasures are displayed on the smart phone 6 If the smart phone fails to recognize the information code more than twice enter the information code displayed on the display panel of the dryer manually into the Smart Care app NOTE Precautions when using Smart Care e If light from a light bulb fluorescent bulb or lamp is reflected on the display panel of the dryer the smart phone may not be able to recognize the panel or information code easily e f you hold the smart phone at too large an angle relative to
7. e S gt pm oD q ice WY Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Please store the manual in a safe location close to the appliance for future reference Use this appliance only for its intended purpose as described in this instruction manual Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur It is your responsibility to use common sense caution and care when installing maintaining and operating your dryer Because the following operating instructions cover various models the characteristics of your dryer may differ slightly from those described in this manual and not all warning signs may be applicable If you have any questions or concerns contact your nearest service center or find help and information online at www samsung com Important safety symbols What the icons and signs in this user manual mean A N WARNING Hazards or unsafe practices that may result in severe personal injury death and or property damage N CAUTION Hazards or unsafe practices that may result in personal injury and or property damage NOTE Indicates that a risk of personal injury or material damage exists SAVE THESE INSTRUCTIONS 4 English DV8000J 03170M 01_EN US_150122 indd 4 a 2015 1 23 16 29 53 These warnin
8. 3 ah Ibs g DELICATES Underwear blouses lingerie re Water repellent wear Normal Dry No ACTIVE WEAR performance clothes sports wear ar A Maximum 4 Ibs g TOWELS Bath towels and similar items Pte QUICK DRY Small loads Manual Dry TIME DRY Any load AIR FLUFF Foam rubber plastic z REFRESH Shirts trouser comforter pillows Steam Dry WRINKLE AWAY Shirts trouser blouses z Bedding curtains children s STEAM SANITIZE AE Very Dry No change 02 O D o p a e3 Er 5 Nn DV8000J 03170M 01_EN US_150122 indd 55 English 55 2015 1 23 16 30 06 Specifications NOTE e factory setting can be selected e WOOL TOWELS available for DV52J8700E G only DV8000J 03170M 01_EN US_150122 indd 56 Temperature setting Time Cycle High Med Med Low Low Extra Low setting NORMAL J ECO NORMAL J HEAVY DUTY e BEDDING J Sensor Dry PERM PRESS J WOOL J DELICATES ACTIVE WEAR J TOWELS e QUICK DRY J e Manual Dry TIME DRY J J J e AIR FLUFF e REFRESH e Steam Dry WRINKLE AWAY J e STEAM SANITIZE e Options svag Anti Static Miec Lest Mone Adjust Time Eco Dry Bell Prevent NORMAL e J ECO NORMAL e HEAVY DUTY J BEDDING Sensor Dry PERM PRESS J WOOL DELICATES
9. 3 Attach the straight end of the long hose to the Y connector 4 Using pliers tighten the coupling with an additional two thirds turn NOTE Do not overtighten as it may damage the coupling S Ww amp wy Va 5 Attach the angled end of the long hoses to the fill valve at the bottom of the dryer s rear frame Screw on the coupling by hand until it is seated on the fill valve connector 6 Using pliers tighten the coupling with an additional two thirds turn NOTE Do not overtighten as it may damage the coupling 7 Turn the cold water faucet on 8 Check for leaks around the Y connector faucets and hoses 26 English DV8000J 03170M 01_EN US_150122 indd 26 a 2015 1 23 16 29 58 Method2 The dryer must be connected to the cold water faucet Using the new inlet hoses Do not use old hoses long hose Canada model only supplied 1 If the Y connector A cannot be attached directly to the cold water faucet the short hose must be used 2 Turn the cold water faucet off 3 Attach the short inlet hose B to the cold water faucet Screw on the coupling by hand until it is seated on the faucet 4 Using pliers tighten the coupling with an additional two thirds turn NOTE Do not overtighten as it may damage the coupling a om w D eo English 27 DV8000J 03170M 01_EN US_150122 indd 27 a 2015 1 23 16 29 58 Installation 5 Atta
10. A Height Insta 48 0 Product 27 0 68 6 B Width Insta 29 0 i i Product 30 0 76 3 Dimensions C Depth i a inches cm Insta 35 0 D Depth with Product 49 80 126 5 door open 90 Install 54 82 E Width with Product 46 47 118 0 door open 130 Install 51 47 Water pressure psi kPa 20 116 137 800 NET weight Ib kg 126 57 Electric W 5300 Heater rating Gas BTU hr 22000 54 English DV8000J 03170M 01_EN US_150122 indd 54 2015 1 23 16 30 05 Cycle chart NOTE For best results follow the load size recommendations for each dry cycle w Large load Fill the drum to about full Do not add items over this level as they need to tumble freely Medium load Fill the drum to about full Q small load Fill the drum with 375 items not more than full Cycle Recommended items ai Dry Level Cottons work clothes linen ormal Dry NORRI mixed loads Adjustable ECO NORMAL Cottons work clothes linen ka Iaa Heavy Fabrics such as jean ormal Dry RIEAN DUTY corduroys heavy work clothes Adjustable Bulky items such as blankets ormal Dry BEDDING sheets comforters pillows Adjustable PERM PRESS Shirts synthetic fabrics knits orma Dry wrinkle free cottons permanent Adjustable Sensor Dry z For machine washable and tumble Normal Dry No WOOL dryable wool only Maximum
11. e Do not reuse a power supply cord from an old dryer The power cord electric supply wiring must be supported at the dryer cabinet by a suitable UL listed strain relief e Grounding through the neutral conductor is prohibited for 1 new branch circuit installations 2 mobile homes 3 recreational vehicles and 4 areas where local codes prohibit grounding through the neutral conductor Use a 4 prong plug for a 4 wire receptacle NEMA type 14 30R e Z Za Electric models Canada Only e A120 240 volt 60 Hz AC approved electrical service fused through a 30 ampere fuse or circuit breaker on both sides of the line is required e All Canadian models are shipped with the power cord attached The power cord should be plugged into a 30 ampere receptacle NOTE It is not permissible to convert a dryer in Canada to 208 volts 20 English DV8000J 03170M 01_EN US_150122 indd 20 a 2015 1 23 16 29 56 Step by step installation For proper installation we recommend that you hire a qualified installer Read these instructions completely before you begin the installation To install the dryer follow these steps 1 Move your dryer to an appropriate location for installation Consider installing the dryer and washer sideby side so you have easy access to both appliances NOTE To move the dryer easily lay two of the carton cushion tops on the floor Tip your dryer on its side so it lies across both cushion t
12. DV8000J 03170M 01_EN US_150122 indd 23 a 2015 1 23 16 29 57 Installation A N WARNING For U S models Risk of electrical shock e All US models are designed for a 3 WIRE SYSTEM CONNECTION The dryer frame is grounded to the neutral conductor at the terminal block A 4 WIRE SYSTEM CONNECTION is required for new or remodeled construction mobile homes or if local codes do not permit grounding through neutral If you use the 4 wire system you cannot ground the dryer frame to the neutral conductor at the terminal block e Remove the terminal block cover plate Insert the power cord with a UL listed strain relief through the hole provided in the cabinet near the terminal block e A strain relief must be used Do not loosen the nuts already installed on the terminal block Be sure they are tight Use a 3 8 1cm deep well socket e amp wy Va 9 To ensure that the dryer provides optimal drying performance it must be level To level the dryer follow the lettered steps below A Using a leveller A check if the dryer is level side to side and then front to back B If the dryer is not level adjust the leveling feet B on the bottom of the dryer until the dryer is level side to side and back to front Turning the feet clockwise retracts the feet Turning the feet clockwise loosens and extends them 24 English DV8000J 03170M 01_EN US_150122 indd 24 a 2015 1 23 16 29 57 NOT
13. Do not contact this part while appliance is energized S Ww amp wy Va Basic requirements Make sure you have everything necessary for proper installation e A GROUNDED ELECTRICAL OUTLET is required See Electrical Requirements e A POWER CORD for electric dryers except in Canada e GAS LINES if installing a gas dryer The gas lines must meet national and local codes e EXHAUST SYSTEM must be rigid metal or flexible stiff walled metal exhaust ducting 12 English DV8000J 03170M 01_EN US_150122 indd 12 a 2015 1 23 16 29 55 Location considerations Locate the dryer where there is enough space at the front for loading the dryer and enough Space behind for the exhaust system This dryer is factory ready for rear exhaust To exhaust out the bottom or the right or the left electric model only use the accessory exhaust kit sold separately Instructions are included with the kit It s important to make sure the room has enough fresh air The dryer must be located where there is no air flow obstruction On gas dryers adequate clearance as noted on the data plate must be maintained to ensure adequate air for combustion and proper dryer operation Do not install or store the dryer in an area where it will be exposed to water and or weather Keep the dryer area clear of combustible materials gasoline and other flammable vapors and liquids A dryer produces combustible lint The area around the dryer should
14. IMPLIED WARRANTIES OF MERCHANTABILITY INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS OR ANY OTHER SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE MISUSE OR INABILITY TO USE THIS PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE WITHOUT LIMITING THE FOREGOING PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS DAMAGE OR INJURY TO PURCHASER AND PURCHASER S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE MISUSE OR INABILITY TO USE THIS PRODUCT THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY English 61 DV8000J 03170M 01_EN US_150122 indd 61 2015 1 23 16 30 06 oe Warranty CANADA Some provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you
15. and create a fire hazard 36 English DV8000J 03170M 01_EN US_150122 indd 36 a 2015 1 23 16 30 03 Operations Z N WARNING To reduce the risk of fire electric shock or injury to persons read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance Control panel DV52J8700E G Manual Dry Hold 3 sec ECO NORMAL NORMAL TOWELS 06 _ i 40 A Anti Static O eoa TT Ac My Cycle HEAVY DUTY UJ QUICK DRY wt cycle Save Filter Check 07 BEDDING f N a TIME DRY x Vent Sensor Drying Cooling Wine en End Rack Dry Adjust Very Dry High 60min Time a PERM PRESS AIR FLUFF More Dry Medium 50min 8 T Normal Dry Med Low 40min gt Mixed Adjust WOOL REFRESH Loadpel Less Dry Low 30min eie DampDry Extra Low 20min DELICATES WRINKLE AWAY 09 wrinkle g Dry Level J Temp E Time ACTIVE WEAR STEAM SANITIZE ae Sau Light an Smart Care Sensor Dry Steam Cycles DV52J8060E G Manual Dry Hold 3 sec lo sec ECO NORMAL NORMAL QUICK DRY 7 steam 11 Anti Static pm Ea aD My Cycle a am J cycle Save HEAVY DUTY j TIME DRY 9 ee Ltt a Y S Y A Filter Check ae 5 BEDDING f AIRFLUFF og Genser ha cota wre en Adjust ack Dry DN High oma Time a PERM PRESS ES REFRESH More Dry Medium 50min suo1 eJ do E Normal Dry Med Low 40min DELICATES Ee WRINKLE Mixed Adjust AWAY Load Bell Sey an Semin Timev e k Damp Dry Extra Lo
16. and medium temperature setting Add a couple of dry towels to absorb moisture and shorten drying time Foam Rubber rug Do not dry on a heat setting Use the AIR FLUFF backs stuffed toys A WARNING shoulder pads etc Drying a rubber item with heat may damage it or create a fire hazard Pillows Plastics Shower curtains outdoor furniture covers etc Use the NORMAL Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the items Do not dry kapok or foam pillows using a heated dryer cycle You can dry these items in the dryer only if you use the AIR FLUFF Use the AIR FLUFF or the TIME DRY and the Low or Extra Low temperature settings depending on the care label instructions A N WARNING Do not dry in the dryer Fiberglass items curtains draperies etc e Woolens unless recommended on the label Items spotted or soaked with vegetable or cooking oils DV8000J 03170M 01_EN US_150122 indd 43 English AP 43 ie pe a w n 2015 1 23 16 30 04 Operations DV8000J 03170M 01_EN US_150122 indd 44 Operations Options Child Lock Child Lock prevents children from playing with the dryer When Child Lock is activated all buttons except for the Power button are disabled To activate deactivate Child Lock simultaneously press and hold Temp and Time for 3 seconds NOTE If Child Lock is activat
17. be kept lint free a om w D ee eo Alcove or closet installation Minimum clearances between the dryer and adjacent walls or other surfaces are 2 in front 17 on top 1 on either side and 5 in the back The closet front must have two unobstructed air openings for a combined minimum total area of 72 in with 3 minimum clearance on the top and bottom A louvered door with equivalent space clearance is acceptable Z N WARNING e You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in and alcove or closet e To reduce the risk of fire you must exhaust the dryer to the outdoors See Exhausting section e No other fuel burning appliance should be installed in the same closet as the dryer English 13 DV8000J 03170M 01_EN US_150122 indd 13 a 2015 1 23 16 29 55 Installation Ducting requirements Weather hood type Recommended Use only for short run installation 5 ke a ic 5 va 4 10 2 cm 2 5 6 4 cm No of 90 ats Metallic nt Metallic elbows Rigid flexible Rigid flexible 0 80 ft 24 4 m 41 ft 12 4 m 74 ft 22 6 m 33 ft 10 1 m il 68 ft 20 7 m 37 ft 11 2 m 62 ft 18 9 m 29 ft 8 8 m 2 57 ft 17 4 m 33 ft 10 1 m 51 ft 15 5 m 25 ft 7 6 m 3 47 ft 14 3 m 29 ft 8 8 m 41 ft 12 5 m 21 ft 6 5 m NOTE Do not use non metallic flexible duct e Usea 4
18. is complete Water drips from the nozzle when SteamCare starts This is steam condensation The dripping water will stop after a short time English DV8000J 03170M 01_EN US_150122 indd 50 2015 1 23 16 30 05 Problem Action Sprayed water Is not visible during e Sprayed water is difficult to see when the door is closed SteamCare e Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is Extended time reached The drying time can change according to the type and amount of laundry See the cycle chart for reference If a problem persists contact a local Samsung service center 5 Oo Cc oO g 7 F ie je ep Ce English 51 DV8000J 03170M 01_EN US_150122 indd 51 a 2015 1 23 16 30 05 oe Troubleshooting Information codes If the dryer fails to operate you may see an information code on the screen Check the table below and try the suggestions CODE MEANING SOLUTION TE The thermistor resistance is very low or Clean the screen or vent high If the problem continues call for service HC Invalid heating Temp when the dryer is Sal far cervice running DC Running the dryer with door open Close the door and then restart If the problem continues call for service Try restarting the cycle FC Invalid power source frequency If th
19. lightweight items e Large bulky items such as blankets or comforters may require repositioning to ensure even drying e Make sure that the dryer is draining properly to extract adequate water from the load e The load may be too small to tumble properly Add a few towels and restart the dryer e The load may be too large to tumble properly Remove some items and restart the dryer e Clean the filter case e Clean the heat exchanger filter e Clean the condenser e Make sure the front lower grill is not clogged Does not dry e Check the load for objects such as coins loose buttons nails etc Remove promptly It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle e Make sure the dryer is levelled properly as outlined in the installation instructions e Itis normal for the dryer to hum due to the high velocity of air moving through the dryer drum fan or exhaust system IS noisy 5 Oo Cc oO g 7 F ie Oo ep Ce English 49 DV8000J 03170M 01_EN US_150122 indd 49 a 2015 1 23 16 30 05 pa je je iS Wn amp Q n ke oe Troubleshooting Problem Action Dries unevenly Seams pockets and other similarly heavy areas may not be completely dry when the rest of the load has reached the selected dryness level This is normal You can choose a higher dryness level or a cycle that in
20. the front of the display panel it may not be able to recognize the information code For best results hold the smart phone so that the front of the panel and the smart phone are parallel or nearly parallel e The information code history is deleted after you use this function DV8000J 03170M 01_EN US_150122 indd 45 ie O D w Er 2 Nn English 45 2015 1 23 16 30 04 oe Maintenance Keep the dryer clean to prevent deteriorated performance and to preserve its life cycle Vent Sensor Your Samsung dryer is equipped with a Vent Sensor which detects and notifies you when it is time to clean the ductwork Keep your dryer safe and efficient by cleaning the ducts when prompted See the table below for an explanation of RE indicator codes Level X indicator Status Solution 0 off The ductwork is free from blockages wne 7 part ore one oF he Check the duct connection lint filter is blocked by lint or P n and shorten the duct and 1 Lights up g ue straighten it if necessary When the resistance is high because the duct is too long or bent Check the lint filter or the duct and clean it if necessary Check the duct connection and shorten the duct and straighten it if necessary Check the lint filter or the duct and clean it as soon as possible In the LEVEL 2 state the X indicator blinks for 3 hours after the completion of the cycle If the Wrinkle Prevention function is activat
21. va 02 am Kl Paes a 03 gt J amp 04 a SZ N A fr D Uy 05 01 Control panel 02 Work top 03 Filter 04 Door 05 Duct exhaust 10 English DV8000J 03170M 01_EN US_150122 indd 10 a 2015 1 23 16 29 54 SF Y connector Rubber washer Water hose Short water hose Canada model only supplied 4 a N WARNING aj Packing materials can be dangerous to children Keep all packing material plastic bags polystyrene etc well out of children s reach CAUTION e Do not move the product while holding the front part of the top cover of the dryer This may cause the cover to separate from the dryer and result in injury e Wear protective gloves whenever lifting or carrying the dryer to prevent personal injury or strain Tools needed for installation Pliers Cutting knife Pipe wrench for gas Nut drivers model only Leveller Phillips screwdriver Duct tape Wrench English 11 DV8000J 03170M 01_EN US_150122 indd 11 a 2015 1 23 16 29 55 Installation Before installation Please read the following instructions carefully before installing the dryer These instructions should be kept for future reference A N WARNING Remove the door from all discarded appliances to avoid the danger of a child suffocating Control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing Service personnel
22. you start When you need to use drying rack refer to the following steps for installation 1 Place the drying rack A inside the tumbler and then align the holes of in the filter handle of the drying rack with the front projections 2 Place the rear legs in the two recessed areas of the tumbler s back wall and then push down the middle of the drying rack to fix it in place 3 Place the items to be dried on the rack leaving space between them so air can circulate 4 Press RACK DRY and then select the time according to the moisture and weight of the item Before you start Drying suggestions Items Setting Washable sweaters block to shape and lay flat on rack TIME DRY with Extra Low temperature setting Stuffed toys cotton or polyester fiber filled Stuffed toys foam or rubber filled Foam rubber pillows AIR FLUFF Sneakers NOTE e Place the drying rack inside the dryer align the holes of the filter handle of the drying rack with the front projections and then secure the back of the drying rack e lf this model does not come with the drying rack you can purchase it through a Samsung service center A N WARNING e You must remove the drying rack from its packaging before you use it Never use the drying rack while it is still in its packaging e Drying foam rubber plastic or rubber on a heat setting may damage the items
23. 2 indd 34 a 2015 1 23 16 30 02 oe Before you start Guideline Sorting and loading e Place only one wash load in the dryer at a time e Avoid mixing heavy and lightweight items together e To increase drying efficiency when drying one or two items add a dry towel to the load e For best results untangle items before inserting into the dryer e Overloading restricts tumbling action and results in uneven drying and wrinkling e Unless recommended on the care label avoid drying woolens or fiberglass items e Avoid drying Unwashed items e Do not dry items soiled with oil alcohol gasoline etc Cleaning the lint filter Clean the lint filter after or before every load This is to prevent a fire hazard 1 Pull out the lint filter A 2 Remove the lint 3 Slide the lint filter back into the place N CAUTION Do not operate the dryer without the lint filter in place Do not use a damaged or broken filter case This may cause degraded performance and or fire es oO sh ie g9 lt ie Cc n eat fed aI Rack Dry The drying rack is installed in the drum at the factory Before using this dryer for the first time remove the drying rack from the drum Pull the rack straight up and then take it out of the drum Remove the drying rack from its packaging and store the rack for later use English 35 DV8000J 03170M 01_EN US_150122 indd 35 a 2015 1 23 16 30 02 oe Before
24. ARNING To reduce the risk of fire or explosion e Do not dry items that have been previously cleaned washed soaked or spotted with gasoline dry cleaning solvents or other flammable or explosive substances They emit vapors that could ignite or explode Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed There are many highly flammable items used in homes such as acetone denatured alcohol gasoline kerosene some liquid household cleaners some spot removers turpentine wpees and wpe removers e tems containing foam rubber may be labeled latex foam or similarly textured rubberlike materials must not be dried on a heat setting Heated foam rubber materials can under certain circumstances produce fire by spontaneous combustion a D 2i D 2 5 O ER 3 D md a 5 A WARNING What to do if you smell gas e Do not try to light any appliance e Do not turn on the appliance e Do not touch any electrical switch e Do not use any phone in your building e Clear the room building or area of all occupants e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e f you cannot reach your gas supplier call the fire department e Installation and service must be performed by a qualified installer service agen
25. ASER AND PURCHASER S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE MISUSE OR INABILITY TO USE THIS PRODUCT THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY 58 English DV8000J 03170M 01_EN US_150122 indd 58 2015 1 23 16 30 06 Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state To obtain warranty service please contact SAMSUNG at Samsung Electronics America Inc 85 Challenger Road Ridgefield Park NJ 07660 1 800 SAMSUNG 726 7864 www samsung com us support Visits by a Service Engineer to explain functions maintenance or installation is not covered by warranty Please contact your Samsung call agent for help with any of these issues English 59 DV8000J 03170M 01_EN US_150122 indd 59 a 2015 1 23 16 30 06 oe Warranty CANADA SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product as supplied and distributed by SAMSUNG ELECTRONICS CANADA INC SAMSUNG and delivered new in the original carton to the original consumer purchaser is warranted by SAMSUNG against manufacturing defe
26. Dryer User manual DV52J8700E G DV52J8060E G 2015 1 23 16 29 53 DV8000J 03170M 01_EN US_150122 indd 1 Contents Safety information Important safety symbols Important safety precautions Contents Installation What you need to Know about the safety instructions Or What s included Before installation Basic requirements Location considerations Ducting requirements Exhausting Gas requirements Electrical requirements Grounding Electrical connections Step by step installation Connecting the inlet hose Final installation check list Dryer exhaust tips Door reversal Before you start Guideline Operations Control panel Simple steps to start Cycle overview Cycle guide Options Maintenance Vent Sensor Cleaning 2 English DV8000J 03170M 01_EN US_150122 indd 2 2015 1 23 16 29 53 Troubleshooting 48 Checkpoints 48 A Information codes 52 e D Specifications 53 Protecting the environment 53 Specification sheet 54 Cycle chart 55 English 3 DV8000J 03170M 01_EN US_150122 indd 3 a 2015 1 23 16 29 53 oe Safety information Congratulations on your new Samsung dryer This manual contains important information on the installation Use and care of your appliance Please take some time to read this manual to take full advantage of your dryer s many benefits and features What you need to Know about the safety instructions iS
27. E If you have a dryer and dryer e To set the dryer to the same height as the washer fully retract A the leveling feet by turning them counterclockwise then loosen B the feet by turning them clockwise Once the dryer is the same height as the washer follow the directions above to level the dryer e Adjust the leveling feet only as much as necessary to level the dryer Extending the leveling feet more than necessary can cause the dryer to vibrate a om w D eo 10 Make sure all gas connections on gas models and exhaust and electrical connections are complete Plug in your dryer and then check its operation by using the checklist on page 28 11 For GAS MODELS ONLY The burner may not ignite initially due to air in the gas line Allowing your dryer to operate on a heat setting will purge the line If the gas does not ignite within 5 minutes turn your dryer off and wait 5 minutes Be sure the gas supply to your dryer has been turned on To confirm gas ignition check the exhaust for heat English 25 DV8000J 03170M 01_EN US_150122 indd 25 a 2015 1 23 16 29 58 Installation Connecting the inlet hose Method1 The dryer must be connected to the cold water faucet using the new inlet hoses Do not use old hoses long hose Canada model only supplied 1 If space permits attach the brass female end of the Y connector to the cold water faucet 2 Turn the cold water faucet off
28. Install and use in accordance with the manufacturer s instructions e amp wy Va Electrical requirements NOTE The wiring diagram is located on the plate below the control panel or frame back N WARNING e Improperly connecting the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded Do not modify the plug provided with your dryer if it doesn t fit the outlet have a proper outlet installed by a qualified electrician e To prevent unnecessary risk of fire electrical shock or personal injury all wiring and grounding must be done in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA No 70 Latest Revision for the U S or the Canadian Electrical Code CSA C22 1 Latest Revisions and local codes and ordinances It is your responsibility to provide adequate electrical services for your dryer e All gas installations must be done in accordance with the national Fuel Code ANS I Z2231 Latest Revision for the U S or CAN CGA B149 Installation Codes Latest Revision for Canada and local codes and ordinances 18 English DV8000J 03170M 01_EN US_150122 indd 18 a 2015 1 23 16 29 56 Grounding This dryer must be grounded In the event of malfunction or breakdown the ground will reduce the risk of electrical shock by p
29. J e ACTIVE WEAR TOWELS e QUICK DRY e Manual Dry TIME DRY e Ww AIR FLUFF e 6 REFRESH t Steam Dry WRINKLE AWAY e S STEAM SANITIZE D a 56 English 2015 1 23 16 30 06 oe Warranty U S A SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product as supplied and distributed by SAMSUNG ELECTRONICS AMERICA INC SAMSUNG and delivered new in the original carton to the original consumer purchaser is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of e One 1 Year All Parts and Labor e Two 2 Years Control Board Parts Part Only This limited warranty begins on the original date of purchase and is valid only on products purchased and used in the United States To receive warranty service the purchaser must contact SAMSUNG for problem determination and service procedures Warranty service can only be performed by a SAMSUNG authorized service center The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG s authorized service center SAMSUNG will provide in home service during the warranty period at no charge subject to availability within the contiguous United States In home service is not available in all areas To receive in home service product must be unobstructed and accessible to the service agent If service is not available SAMSUNG may ele
30. M 01_EN US_150122 indd 15 a 2015 1 23 16 29 56 Installation Exhausting The dryer must not be exhausted into a chimney a wall a ceiling an attic a crawl space or a concealed space of a building Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room In the United States e All dryers must be exhausted to the outside e The required exhaust duct is 4 inches 10 2 cm in diameter e Use only those foil type flexible ducts if any specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct Use Subject 2158A e See Ducting requirements in the Installation section for the maximum duct length and number of bends that can be used e The total length of flexible metal duct must not exceed 7 10 2 4 m e Do not assemble the duct with screws or other fasteners means that extend into the duct and catch lint e amp Va In Canada e All dryer must be exhausted to the outside e The exhaust duct should be 4 inches 10 2 cm in diameter e Use only those foil type flexible ducts if any specifically indentified for use with the appliance by the manufacturer shall be used e See Ducting requirements in the Installation section for the maximum duct length and number of bends e The total length of flexible metal duct shall not exceed 7 10 2 4 m
31. aised 18 inches 46 cm above the floor Additionally a 1 8 0 3 cm N PT National Pipe Thread plugged tapping accessible for test gauge connection must be installed immediately Upstream of your dryer s gas supply connection e Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system e DO NOT reuse old flexible metal gas lines Flexible gas lines must be design certified by the American Gas Association CGA in Canada a om w D eo NOTE e Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas e As a courtesy most local gas utilities will Inspect a gas appliance installation NOTE GAS IGNITION Your dryer uses an automatic ignition system to ignite the burner There is no constant burning pilot English 17 DV8000J 03170M 01_EN US_150122 indd 17 a 2015 1 23 16 29 56 Installation Commonwealth of Massachusetts installation instructions Your dryer must be installed by a licensed plumber or gas fitter A T handle manual gas valve must be installed in the gas supply line to your dryer If a flexible gas connector is used to install your dryer the connector can be no longer than 3 36 A N WARNING e Gas leaks may occur in your system creating a dangerous situation e Gas leaks may not be detected by smell alone e Gas suppliers recommend you purchase and install a UL approved gas detector e
32. ce and environmental instructions that are covered and prescribed in the instruction book product removal and reinstallation problems caused by pest infestations This limited warranty does not cover problems resulting from incorrect electric current voltage or supply light bulbs house fuses house wiring cost of a service call for instructions or fixing installation errors SAMSUNG does not warrant uninterrupted or error free operation of the product EXCEPT AS SET FORTH HEREIN THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS OR ANY OTHER SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE MISUSE OR INABILITY TO USE THIS PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE WITHOUT LIMITING THE FOREGOING PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS DAMAGE OR INJURY TO PURCH
33. ch the Y connector to the brass male end of the small hose Screw on the coupling by hand until it is seated on the connector 6 Using pliers tighten the coupling with an additional two thirds turn NOTE Do not overtighten as it may damage the coupling 7 Attach the angled end of water hoses C to the fill valve at the bottom of the dryer rear frame Screw on the coupling by hand until it is seated on the fill valve connector 8 Using pliers tighten the coupling with an additional two thirds turn NOTE Do not overtighten as it may damage the coupling 9 Turn the cold water faucet on 10 Check for leaks around the Y connector faucets and hoses e amp wy Va Final installation check list e The dryer is plugged into an electrical outlet and grounded properly e The exhaust ductwork is hooked up and the joints are taped e You have used rigid or stiff walled flexible metal duct material not plastic flexible duct e The dryer is level and is sitting firmly on the floor e For gas models The gas is turned on and there are no gas leaks e Start your dryer to confirm that it runs heats and shuts off 28 English DV8000J 03170M 01_EN US_150122 indd 28 a 2015 1 23 16 29 59 Dryer exhaust tips WARNING Plastic or non metal flexible duct presents a potential fire hazard 1 Make sure your dryer is installed properly so it exhausts air easily
34. ct to provide transportation of the product to and from an authorized service center SAMSUNG will repair replace or refund this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer English 57 DV8000J 03170M 01_EN US_150122 indd 57 a 2015 1 23 16 30 06 oe Warranty U S A This limited warranty covers manufacturing defects in materials and workmanship encountered in normal noncommercial use of this product and shall not apply to the following damage that occurs in shipment delivery and installation applications and uses for which this product was not intended altered product or serial numbers cosmetic damage or exterior finish accidents abuse neglect fire water lightning or other acts of nature or God use of products equipment systems utilities services parts supplies accessories applications installations repairs external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems incorrect electrical line voltage fluctuations and surges customer adjustments and failure to follow operating instructions maintenan
35. cts in materials and workmanship for a limited warranty period of e One 1 year part and labor This limited warranty begins on the original date of purchase and is valid only on products purchased and used in the Canada To receive warranty service the purchaser must contact SAMSUNG for problem determination and service procedures Warranty service can only be performed by a SAMSUNG authorized service center The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNC s authorized service center SAMSUNG will provide in home service during the warranty period at no charge subject to availability within the Canada In home service is not available in all areas To receive in home service product must be unobstructed and accessible to the service agent If service is not available SAMSUNG may elect to provide transportation of the product to and from an authorized service center SAMSUNG will repair replace or refund this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer 60 English DV8000J 03170M 01_EN US_150122 indd 60 a 2015 1 23 16 30 06
36. cy or the gas supplier VAN WARNING Gas Appliances This product contains chemicals known to the State of California to cause cancer and reproductive toxicity Gas appliances can cause low level exposure to Proposition 65 listed substances including but not limited to benzene carbon monoxide formaldehyde and soot substances resulting from the incomplete combustion of natural gas or LP fuels SAVE THESE INSTRUCTIONS English 7 DV8000J 03170M 01_EN US_150122 indd 7 a 2015 1 23 16 29 53 oe Safety information Warnings N WARNING Ensure pockets are free from small irregularly shaped hard objects foreign material etc ie coins knives pins etc These objects could damage your dryer je L gt pm 9 q igo Wn Gas leaks may occur in your system resulting in a dangerous situation Cautions CAUTION Do not allow children or pets to play on in or in front of the appliance Close supervision is necessary when the appliance is used near children and pets Before discarding or removing your dryer from service remove the door to the drying compartment to prevent children or animals from becoming trapped inside Do not reach into the appliance when the drum is moving Do not install or store this appliance where it will be exposed to the weather Do not tamper with controls Do not repair replace or attempt to service any part of the appliance unless speci
37. e Do not assemble the duct with screws or other fasteners means that extend into the duct and catch lint Outside the U S and Canada e Refer to the local codes A N WARNING You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in an alcove or closet NEVER USE A PLASTIC OR NON METAL FLEXIBLE DUCT If your existing ductwork is plastic non metal or combustible replace it with metal Use only a metal exhaust duct that is non flammable to ensure containment of exhaust air heat and lint 16 English DV8000J 03170M 01_EN US_150122 indd 16 a 2015 1 23 16 29 56 Gas requirements Z N WARNING e Use only natural or LP liquid propane gases e THE INSTALLATION MUST CONFORM WITH LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES WITH THE NATIONAL FUEL GAS CODE ANSI Z223 1 LATEST REVISION FOR THE UNITED STATES OR WITH THE CAN CGA B149 INSTALLATION CODES FOR CANADA e Gas dryers are equipped with a burner vent for use with natural gas If you plan to use your dryer with LP liquid propane gas it must be converted for safe and proper performance by a qualified service technician e A 1 2 1 27 cm gas supply line is recommended and must be reduced to connect to the 3 8 1 cm gas line on your dryer The National Fuel Gas Code requires that an accessible approved manual gas shut off valve be installed within 6 of your dryer e Gas dryers installed in residential garages must be r
38. e problem continues call for service Electronic Control Problem i 9C1 Invalid Voltage PANO RENICE AC Electronic Control Problem callforservic Invalid Communication i DF Invalid door Call for service BC2 Unit detects a button is being pressed for dee ecules int ee a over 30secs or button is stuck yy 9 y X If the problem continues call for service If any information code keeps appearing on the screen contact a local Samsung service center S p je je is Va x a je ke 52 English DV8000J 03170M 01_EN US_150122 indd 52 a 2015 1 23 16 30 05 Specifications Protecting the environment This appliance is manufactured from recyclable materials If you decide to dispose of this appliance please observe local waste disposal regulations Cut off the power cord so that the appliance cannot be connected to a power source Remove the door so that animals and small children cannot get trapped inside the appliance 02 O D o p ie e3 Er 5 Nn English 53 DV8000J 03170M 01_EN US_150122 indd 53 a 2015 1 23 16 30 05 Specifications Specification sheet NOTE A Height Spec range through the leveling feet adjustment 116 8 118 0 cm Ww Cc i pa go v e Q WN Type Front loading dryer DV52J8700E G Woden igine DV52J8060E G Product 46 0 116 8
39. ean with a soft damp cloth Do not use abrasive substances Do not spray cleaners directly on the panel The control panel finish may be damaged by some laundry pre treatment soil and stain remover products Apply such products away from your dryer and wipe up any spills or overspray immediately Tumbler Remove any stains from the tumbler caused by crayon ink fabric dye from new items such as towels or jeans and so on with an all purpose cleaner Tumble old towels or rags to remove any remaining stain or cleaning substance Once these steps are followed stains may still be visible but should not transfer to subsequent loads Stainless steel tumbler To clean the stainless steel tumbler use a damp cloth with a mild non abrasive cleaner suitable for easily marred surfaces Remove cleaner residue and dry with a clean cloth Dryer Exterior Clean with a soft damp cloth Do not use abrasive substances Protect the surface from sharp objects Do not place any heavy or sharp objects or a detergent box on the dryer They can scratch or damage the top cover of the dryer Keep these items in a separately purchased pedestal or in a separate storage box The entire dryer has a high gloss finish Avoid scratching or damaging the surface when using the dryer Dryer Exhaust System Inspect and clean the dryer exhaust system yearly to maintain optimum performance The outside exhaust hood should be cleaned more freque
40. ed and the dryer is turned off and then on again Child Lock remains activated Drum Light Lights the dryer drum while the dryer is running Press and hold Wrinkle Prevent for 3 seconds or longer NOTE You can turn the drum light on and off while your dryer is running and when it is stopped If you do not turn the drum light off 5 minutes after turning it on the drum light automatically turns off Sound The Sound Off function can be selected during all cycles Press and hold Dry Level for 3 seconds or longer NOTE When this function is selected sound is turned off for all cycles Even if the power is turned off and on repeatedly the setting is retained 44 English My Cycle Allows you to load your custom drying cycle Cycle Dry Level Temp and so on with one button convenience Press My Cycle for less than 3 seconds to load and use the stored My Cycle The My Cycle lamp lights up and the selected cycle and option lamps blink To set or change your own My Cycle 1 Press Power 2 Select a cycle using the Cycle Selector 3 After cycle selection set each option Dry Level Temp Time and so on 4 Press and hold My Cycle for longer than 3 seconds The dryer stores the selected cycle and options Smart Care Smart Care lets you check the status of your dryer using a smart phone if it displays an information code To use Smart Care you need e The Samsung Smart Care app e Asmart phone
41. ed this message is displayed for up to 3 hours If the Power button is pressed or the door is opened the power is immediately turned off NOTE For more information about the duct installation please refer to the Ducting requirements section on page 14 e Although the dryer is available even if the blockage message is displayed the drying time may be extended e If the LEVEL 1 message is displayed the first time the dryer is run after installation check the the lint filter and the connection between the duct and the dryer and clean the duct If the LEVEL 1 message appears even after you have checked and cleaned the ducts this may indicate that there are some restrictions of the duct due to the length condition etc If this occurs you can use the dryer normally and no countermeasures need to be taken However the drying time may be extended or the drying performance may be degraded When the duct is blocked by lint or a foreign object 2 Blinks When the resistance is very high because the duct is too long or bent excessively Maintenance 46 English DV8000J 03170M 01_EN US_150122 indd 46 a 2015 1 23 16 30 05 DV8000J 03170M 01_EN US_150122 indd 47 A N WARNING Control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing Service personnel Do not contact this part while appliance is energized Cleaning Control Panel Cl
42. fically instructed to in the user repair instructions and you have the understanding and skills to carry out the procedure Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product Clean the lint screen before or after each load Keep the area around the exhaust opening and surrounding areas free from lint dust and dirt The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel SAVE THESE INSTRUCTIONS 8 English DV8000J 03170M 01_EN US_150122 indd 8 a 2015 1 23 16 29 54 This appliance must be properly grounded Never plug the power cord into a receptacle that is not grounded adequately or not in accordance with local and national codes See installation instructions for information about grounding this appliance Do not sit on top of the dryer Do not wash clothing with large buckles buttons or other heavy metal or solid objects a D 2i D 2 5 O 3 D md a 5 Gas leaks may not be detected by smell alone Gas suppliers recommend you purchase and install a UL approved gas detector Install and use in accordance with the manufacturer s instructions Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil Even after being washed these items may contain significant amounts of these oils Res
43. g signs are here to prevent injury to yourself and others Please follow them explicitly After reading this manual store it in a safe place for future reference Read all instructions before Using the appliance As with any equipment that uses electricity and moving parts potential hazards exist To safely operate this appliance familiarize yourself with its operation and exercise care when using it WARNING Risk of Fire Clothes dryer installation must be performed by a qualified installer e Install the clothes dryer according to the manufacturer s instructions and local codes e Do not install a clothes dryer with flexible plastic venting materials If flexible metal foil type duct is installed it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers Flexible venting materials are known to collapse be easily crushed and trap lint These conditions will obstruct clothes dryer airflow and increase the risk of fire e To reduce the risk of severe injury or death follow all installation instructions e Save these instructions a D 2i D 2 5 O ER 3 D md a 5 Important safety precautions A N WARNING To reduce the risk of fire electric shock or injury to persons when using your appliance follow basic precautions including the following 1 Read all instructions before using this appliance 2 Do not dry articles that have been pre
44. idual oil on clothing can ignite spontaneoulsy The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat Heat sources such as your dryer can warm these items allowing an oxidation reaction in the oil to occur Oxidation creates heat If this heat cannot escape the items can become hot enough to catch fire Piling stacking or storing these kinds of items may prevent heat from escaping and can create a fire hazard All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous Washing these items in hot water with extra detergent will reduce but not eliminate the hazard Always use the Cool Down cycle for these items to reduce their temperature Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle Never pile or stack these items when they are hot SAVE THESE INSTRUCTIONS English 9 DV8000J 03170M 01_EN US_150122 indd 9 a 2015 1 23 16 29 54 oe Installation Follow these instructions carefully to ensure proper installation of the dryer and to prevent accidents when using it What s included Make sure all the parts are included in the product package If you have a problem with the dryer or the parts contact a local Samsung customer center or the retailer Q w 01 iE
45. inch 10 2 cm diameter rigid aluminum or rigid galvanized steel duct e Do not use a smaller duct e Ducts larger than 4 inches 10 2 cm in diameter can cause increased lint accumulation Lint accumulation should be cleaned regularly e fa flexible metal duct must be used use the type with a stiff sheet metal wall Do not use a flexible duct with a thin foil wall Serious blockage can result if the flexible metal duct is bent too sharply e Never install any type of flexible duct in walls ceilings or other concealed spaces e Keep the exhaust duct as straight and short as possible e Secure joints with duct tape Do not use screws e Plastic flexible duct can kink sag be punctured reduce airflow extend drying times and affect dryer operation e Exhaust systems longer than recommended can extend drying times affect machine operation and may collect lint e The exhaust duct should end with an exhaust hood with a swing out damper to prevent back drafts and the entry of wildlife Never use an exhaust hood with a magnetic damper 14 English DV8000J 03170M 01_EN US_150122 indd 14 2015 1 23 16 29 56 e The hood should have at least 12 inches 30 5 cm of clearance between the bottom of the hood and the ground or other obstruction The hood opening should point down e Never install a screen over the exhaust outlet e To avoid lint buildup do not exhaust the dryer directly into a window well Do not exhaust under a house or
46. ng conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer English 19 DV8000J 03170M 01_EN US_150122 indd 19 a 2015 1 23 16 29 56 Installation Electrical connections Before operating or testing follow all grounding instructions in the Grounding section An individual branch or separate circuit serving only your dryer is recommended DO NOT USE AN EXTENSION CORD Gas models U S and Canada A 120 volt 60 Hz AC approved electrical service with a 15 ampere fuse or circuit breaker is required Electric models U S only Most U S dryers require a 120 240 volt 60 Hz AC approved electrical service Some require 120 208 volt 60 Hz approved electrical service The electric service requirements can be found on the data label located behind the door A 30 ampere fuse or circuit breaker on both sides of the line is required e Ifa power cord is used the cord should be plugged into a 30 ampere receptacle e The power cord is NOT provided with U S electric model dryers Z N WARNING Risk of Electric Shock When local codes allow the dryer electrical supply may be connected by means of a new power supply cord kit marked for Use with a dryer that is ULL listed and rated at a minimum of 120 240 volts 30 ampere with three No 10 copper wire conductors terminated with closed loop terminals open end spade lugs with turned up ends or with tinned leads
47. ntly to ensure proper operation English 47 2015 1 23 16 30 05 z D D D a D oe Troubleshooting Checkpoints If you encounter a problem with the dryer first check the table below and try the suggestions Problem Action e Make sure the door is latched shut e Make sure the power cord is plugged into a live electrical outlet e Check the home s circuit breaker and fuses e Press or tap Start Pause again if the door is opened during a cycle e Empty the water in the condensed water tank e Clean the filter case Does not run e Check the home s circuit breaker and fuses e Some cycles do not require heating Check the selected cycle again e For a gas dryer make sure the gas supply is on Does not heat e Clean the lint filter and exhaust duct e Check the case filter or heat exchanger filter and clean them if necessary e The dryer may have moved into the cool down phase of the cycle fe w je je iS Wn Q e ke 48 English DV8000J 03170M 01_EN US_150122 indd 48 a 2015 1 23 16 30 05 Problem Action e Check all of the above plus e Make sure the exhaust hood outside the home can open and close freely e Check the exhaust system for lint buildup Ducting should be inspected and cleaned annually e Use a 4 rigid metal exhaust duct e Do not overload 1 wash load 1 dryer load e Sort heavy items from
48. o the neutral conductor NOTE We recommend using ring terminals If you use strap terminals please ensure you install them perfectly 22 English DV8000J 03170M 01_EN US_150122 indd 22 a 2015 1 23 16 29 57 8 Four Wire System instructions A External ground connector B Green or bare copper wire of power cord C 1 9 cm UL listed strain relief D Center silver colored terminal block screw E Neutral grounding wire white F Neutral wire white or center wire a Remove the External ground connector screw b Connect the ground wire green or unwrapped of the power cord to the external ground connector screw If you want to connect B Green or bare copper wire of power cord to the Neutral Post without connecting it to A cabinet ground call a service technician c Loosen or remove the center terminal block screw d Connect the neutral wire white or center wire of the power cord and the appliance ground wire white Under the central screw of the terminal block e Connect the other wires to the outer terminal block screws Tighten screws f Tighten the strain relief screws g Insert the tab of the terminal block cover into your dryer s rear panel slot Secure the cover with a hold down screw a om w D eo NOTE We recommend using ring terminals If you use strap terminals please ensure you install them perfectly English 23
49. ops Push the dryer so that it is near its final location Set your dryer upright Leave enough room around the dryer so you can attach the duct work power cord etc 2 If you need to change the direction of the door go to Door reversal on page 31 When done return to Step 3 below 3 Review the Exhausting section before installing the exhaust system Install the duct work from your dryer to the exhaust hood The crimped end of the duct sections must point away from your dryer DO NOT use sheet metal screws when assembling ducting These joints should be taped Never use plastic flexible exhaust material NOTE A tip for tight installations Attach a section of the exhaust system to your dryer before putting it in place Use duct tape to secure this section to your dryer but do not cover the ventilation slots at the back of the dryer cabinet 4 If you have an electric model skip to Step 6 If you have a gas model go to the next step 5 Review the Gas requirements section then follow the lettered steps below A Remove the pipe thread protective cap B Apply pipe joint compound or about 1 1 2 wraps of Teflon tape over all threaded connections The pipe joint compound must be resistant to the action of any liquefied petroleum gas C Connect the gas supply to your dryer An additional fitting is required to connect the 3 4 1 9 cm female thread end of a flexible connector to the 3 8 1 cm male threaded end on the dryer
50. porch e f exhaust ductwork must run through an unheated area the duct should be insulated and Slope slightly down towards the exhaust hood to reduce condensation and lint buildup e Inspect and clean the interior of the exhaust system at least once a year Unplug the power cord before cleaning e Check frequently to be sure the exhaust hood damper opens and closes freely e Check once per month and clean at least one time per year Note If clothes are not getting dry then check ducting for obstructions e Do not exhaust dryer into any wall ceiling crawl space or concealed space of a building gas vent or any other common duct or chimney This could create a fire hazard from lint expelled by the dryer a om w D eo If the new dryer is being installed into an existing exhaust system you must make sure e The exhaust system meets all local state and national codes e That a flexible plastic duct is not used e To Inspect and clean all lint buildup from inside the existing duct e The duct is not kinked or crushed e The exhaust hood damper opens and closes freely The static pressure in any exhaust system must not exceed 0 83 inches of water column or be less than 0 This can be measured with the dryer running with a manometer at the point where the exhaust duct connects to the dryer A no heat setting should be used The dryer tumbler should be empty and the lint filter clean English 15 DV8000J 03170
51. roviding a path of least resistance for the electrical current WARNING Improper connection of the equipment grounding conductor can result in a risk of electric Shock Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly grounded a om w D eo Gas models N WARNING e Your dryer has a cord with an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances e Do not modify the plug provided with your dryer if it doesn t fit the outlet have a proper outlet installed by a qualified electrician e Never connect the ground wire to plastic plumbing lines gas lines or hot water pipes Electric models J N WARNING e Your dryer has an optional cord with an equipment grounding conductor and a grounding plug This cord is sold separately e The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances e Do not modify the plug provided with your dryer if it doesn t fit the outlet have a proper outlet installed by a qualified electrician e If a power cord is not used and the electric dryer is to be permanently wired the dryer must be connected to a permanently grounded metal wiring system or an equipment groundi
52. specific rights and you may also have other rights which vary from province to province To obtain warranty service please contact SAMSUNG at Samsung Electronics Canada Inc 2050 Derry Road West Mississauga Ontario LSN OB9 Canada 1 800 SAMSUNG 726 7864 www samsung com ca support English www samsung com ca_fr support French Visits by a Service Engineer to explain functions maintenance or installation is not covered by warranty Please contact your Samsung call agent for help with any of these issues 62 English DV8000J 03170M 01_EN US_150122 indd 62 a 2015 1 23 16 30 06 Memo English 63 DV8000J 03170M 01_EN US_150122 indd 63 a 2015 1 23 16 30 06 m m Scan the QR code or visit www samsung com spsn to view our helpful How to Videos and Live Shows 4 Requires reader to be installed on your smartphone Scan this with your smartphone QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT U S A 1 800 SAMSUNG 726 7864 WWww samsung com us support www samsung com ca support English www samsung com ca_fr support French MEXICO 01 800 SAMSUNG 726 7864 www samsung com mx support a ENERGY STAR DC68 03170M 01 CANADA 1 800 SAMSUNG 726 7864 DV8000J 03170M 01_EN US_150122 indd 64 a 2015 1 23 16 30 07
53. tatic unless recommended by the manufacturer of the fabric softener or product 12 Clean the lint screen before or after each load 13 Do not use heat to dry articles containing foam rubber or similarly textured rubber like materials 14 Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint dust and dirt 15 The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel 16 Do not place items exposed to cooking oils in your dryer Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire 17 This appliance must be grounded See Electrical requirements and Grounding in Installation section 18 Do not allow children to play on or in the appliance Close supervision of children is necessary when the appliance is used near children 19 Do not insert your hand under the dryer This may result in injury 20 Take care that children s fingers are not caught in the door when closing it e This may result in injury 21 Control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing e Donot contact this part while appliance is energized iS Oo E L gt pm e5 q ie WY ooN SAVE THESE INSTRUCTIONS 6 English DV8000J 03170M 01_EN US_150122 indd 6 a 2015 1 23 16 29 53 A W
54. to open We recommend that you disentangle your laundry before inserting it DV8000J 03170M 01_EN US_150122 indd 39 English 39 a 2015 1 23 16 30 04 Operations Simple steps to start Press Power to turn on the dryer Turn the Cycle Selector to select a cycle Change the cycle settings Dry Level and Time as necessary The dryer provides the additional options Anti Static Rack Dry Mixed Load Bell Wrinkle Prevent and Eco Dry Press to activate deactivate the options 5 Press Start Pause The dryer indicator lights up and the estimated cycle time appears on the display PWN Pe To change the cycle during operation 1 Press Start Pause to stop operation 2 Select a different cycle 3 Press Start Pause again to start the new cycle Operations 40 English DV8000J 03170M 01_EN US_150122 indd 40 a 2015 1 23 16 30 04 Cycle overview Sensor Dry cycles Sensor Dry cycles automatically senses the moisture in the load and shuts the dryer off when the load reaches the dryness level you have selected with Dry Level Cycle Description e For most fabrics including cotton linens and normally soiled garments NORMAL If this cycle is selected the Eco Dry function is enabled by default For more information refer to the description of the Eco Dry option e For reducing energy usage This cycle adjusts cycle time and ECO NORMAL temperature for increased efficiency
55. to reduce wrinkling Press Wrinkle Prevent to activate this feature oa rin e The indicator light above the pad will illuminate when Wrinkle Prevent j Prevent is selected The load is dry and can be removed at any time during the Wrinkle Prevent cycle h r favorit le includin le temp dry level option O e Choose you orite cycle including cycle temp dry level option etc Refer to the My Cycle section on page 44 11 Adjust Time Time can be added or subtracted from the automatically set times in the Manual Dry cycles TIME DRY QUICK DRY or AIR FLUFF and WRINKLE AWAY To add or subtract time from the cycle press the Adjust Time A or V until the desired time is displayed This function is available in the NORMAL and TIME DRY When the Eco Dry function is activated drying takes longer but the power consumption is reduced ie O D pi w Er ie 5 n 12 Eco Dry When the Eco Dry function is enabled the drying time can be extended up to 3 times depending on the specified temperature and the amount of laundry to be dried When the product is shipped the Eco Dry function is set to on by default 13 Power Press to turn on off the dryer 14 Start Pause Press to start or stop an operation NOTE If you insert laundry into your dryer while it is extremely tangled immediately after your washer has finished a wash or spin cycle it may degrade the drying efficiency or cause the door
56. tumbling with heat REFRESH e Removes wrinkles from clothes stored in closets etc It provides wrinkle release via optimized steam care You can change the drying time Minimum time 20 minutes For best results load no more than 3 items WRINKLE AWAY Operations e Sanitizes garments by infusing high temperature heat deep into the fabric and injecting steam during the drying cycle This cycle can make clothes soft and remove bad odors after drying STEAM SANITIZE 42 English DV8000J 03170M 01_EN US_150122 indd 42 a 2015 1 23 16 30 04 Cycle guide Always follow the care label when drying If care label instructions are not available use the following chart Bedspreads amp Follow the care label instructions or dry using the BEDDING Make sure the item is thoroughly dry before using or storing Comforters base Ae f e May require repositioning to ensure even drying e Use the NORMAL and dry only one blanket at a time for best Blankets tumbling action Make sure the item is thoroughly dry before using or storing Curtains amp Draperies Use the PERM PRESS and medium temperature to help minimize wrinkling Dry these in small loads for best results and remove as soon as possible Cloth Diapers Use the NORMAL and the High temperature settings for soft fluffy diapers Down filled Items jackets sleeping bags comforters etc Use the NORMAL
57. utton is not available for Sensor Dry cycles because exact drying times are determined by fluctuating humidity levels Displays all cycle information including cycle time information code and dryer status v CJ Steam mn Drying in progress e a 7 w 05 Digital graphic g Child Lock ae Cooling in progress a display je 4 r Wrinkle Prevent in Filter Check Pee progress Tek Vent Sensor a Cycle is complete Reduces static caused by clothing friction by spraying steam late in a drying cycle The Anti Static function is only available with the NORMAL HEAVY DUTY PERM PRESS DELICATES and TIME DRY 06 Anti Static Rack Dry is available in the TIME DRY Temperature will be 07 Rack Dr f y set to Extra Low only Refer to the Rack Dry section on page 35 The mixed load bell that notifies you when the average dry level in a load is damp dry 80 dried This lets you take garments that you don t want fully dried or that dry quickly out of the oai i el HO dryer early while letting others continue to dry Bell j ADO 5 You can select this function in all Sensor Dry cycles except WOOL and ACTIVE WEAR The dry level selections are limited to Normal Dry More Dry and Very Dry 38 English DV8000J 03170M 01_EN US_150122 indd 38 a 2015 1 23 16 30 04 Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in unheated air at the end of the cycle
58. viously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode 3 Do not use the dryer to dry clothes which have traces of any flammable substance such as vegetable oil cooking oil machine oil flammable chemicals paint thinner etc or anything containing wax or chemicals such as mops and cleaning cloths Flammable substances may cause the fabric to catch fire by itself SAVE THESE INSTRUCTIONS English 5 DV8000J 03170M 01_EN US_150122 indd 5 a 2015 1 23 16 29 53 oe Safety information 4 Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance 5 Do not allow children to play on or in the appliance Close supervision of children is necessary when the appliance is used near children 6 Before the appliance is removed from service or discarded remove the door to the drying compartment Do not reach into the appliance if the drum is moving Do not install or store this appliance where it will be exposed to the weather Do not tamper with internal controls 10 Do not repair or replace any part of the appliance or attempt any service unless Specifically recommended in the user maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out 11 Do not use fabric softeners or products to eliminate s
59. volves such a high dryness level If one heavy item is dried with a light weighing load such as one towel with sheets it is possible that the heavy item will not be completely dry when the rest of the load has reached the selected dryness level For best drying results sort heavy items from lightweight items Has odours Household odours from paint varnish strong cleaners etc may enter the dryer with the surrounding room air This is normal as the dryer draws the air from the room heats it pulls it through the tumbler and exhausts it outside When these odours linger in the air completely ventilate the room before using the dryer Use a cycle featuring the Refresh function If odours persist wash and dry the item again Lint on clothes Make sure the case filter is cleaned before every load For clothes that naturally build up lint clean the filter case during the cycle Some fabrics are lint producers for example a fuzzy white cotton towel and they must be dried separately from clothes that are lint trappers for example a pair of black linen pants Divide larger loads into smaller loads for drying Check pockets thoroughly before drying then dry clothes Remove lint inside the drum before drying Items still wrinkled after Wrinkle Prevent Wrinkle Care Wrinkle Release Small loads of 1 to 4 items work best Load fewer items Load similar type items Take out the items immediately after drying
60. w 20min ACTIVE WEAR s STEAM SANITIZE ment eee py Sensor Dry Steam Cycles Prevent Drum Light Sound child Lock smart Care Pi Turn the Cycle Selector to select the desired cycle The indicator by Cree eek the cycle name lights up Press to adjust the dryness in the Sensor Dry and Steam Dry cycles except STEAM SANITIZE WOOL and ACTIVE WEAR An indicator light illuminates next to the desired dryness level Press the button repeatedly to scroll through the Dry Level options 02 Dry Level Larger or bulkier loads may require the Very Dry or More Dry for complete dryness Less Dry is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle Damp Dry is designed to partially dry items Use for items that lay flat or hang to dry English 37 DV8000J 03170M 01_EN US_150122 indd 37 a 2015 1 23 16 30 03 Operations Press to change the temperature for the current cycle e High For sturdy cottons or those labeled Tumble Dry e Medium For permanent press synthetics lightweight cottons or items labeled Tumble Dry Medium e Med Low For heat lower than Medium Use to dry synthetic or pa ieme washable knit fabrics e Low For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm e Extra Low Provides the lowest heated drying temperature possible Press to adjust the drying time when using Manual Dry cycles 04 Time This b

User manual

Contents

Download Pdf Manuals

Related Search

Related Contents