BX-2 Metaroll Pump Dispenser User Manual
Contents
1. O one 1A discharge operation SO a aM 5 P PS Speed dial is set to 0 The the dial to accelerate speed Further adjustment in the interval time which is set before negative Pressure SECLORA F eee nin e innit operation is also adjustable Tube is not properly set in a groove Tube Ee moves Tube is not accustomed fully Cerihe mibe acm omedd wel i when Teflon tubes only 3 Operation Guide liquid is re nr rr aT ee dispensed The cue oe nie Use specified tube e Put the plug into the outlet Turn the power on Teflon tubes aay e Set the tube onto the roller please refer to figure 3 eeeseej ae ee Sn ee ea uide is not properly se et the guide proper e Set the direction mode and operation mode Liquid ES oe hs Liquid flowing direction CW Reverse CCW Forward does Guide support pulse not Tighten the bolt up firmly not firmly tighten up 2 Operation mode dra e a R C Finger Foot S W Tube is not specified one Use specified tube TIMER To set operating time Note CONT For continuous use cI merdi Se dineihy ih PIET dedas ean the roller with closth or other appropriates to avoide dusts To hold operation or stop press either STOP or RC or press TIMER _ PPRS ue Pour additional oil into the roller once a month or two months o sto P When any troubles arise contact a selling agent or our company e Set negative pressure interval times according to your operation e Press Fi2. 99 99 sec LED counts down CCW Counterclockwise CW Clockwise To lock a tube guide To support a tube installed in a roller To extract liquids from a tube To hold tube at the both ends which are supported by a roller 1 5 Meter When dispensing is finished it generates output signals Same as 8 For a manual operation Teflon tube 1M option To fix a bottle holder Option J2 BAN SEOK 2 Specification Set the Tube Tyee Metaroll Pump Dispenser e As shown in the right picture press Model BX 2 Guide to loose a bolt and release Guide Time range 0 01 99 99 sec e Put the tube into the right groove of a Rotor Speed 120 rpm max a EMEC e Put the rest of the tube body into the Flow Speed 0 01 6 ml min Teflon tube left tube Holers groove 0 1 20 ml min Silicon tube e After setting the tube turn the roller around a couple of times to allow the Dispense Pressure over 1 5kg cm2 tube flexible movements Direction of Pump Both direction Forward Reverse Power source AC 220V 110V 50 60Hz measurement 182 4mm x 81 2 x 171mm weight 3 kgs 4 Trouble Shooting Trouble Cause Solution Plug is not firmly connected Connect the plug firmly Additional Function The power switch is off Turn the switch on The liquid cutting mechanism enables adjustment in negative pressure for the ir p Le a Mo F is off Replace the fuse with new Negative pressure instantaneous reverse rotation mechanism on ending of
3. BX 2 Metaroll Pump Dispenser User Manual o OF FPF W N 656 253 Seongsu lga Seongdong u 133 821 Korea Table of Contents Parts and Description 29 Specification 4 Operation Guide 4 5 Troubleshooting 5 Additional Data 6 Cautions and Reminders 6 Pump Head Types 7 Environmental conditions for the equipment operation 7 T RAN CEOK 1 Parts and Description TIME DISPLAY lh 00 vir 0 a SPEE A VAJU 6 7 8 lt Figure 1 Frontage gt 162 4 81 2 lt Figure 2 Backside gt CO NDO KR W YP 11 12 13 14 15 16 17 18 19 20 21 Power Switch RC Mode Timer Mode Cont Mode Speed Adjustment Dial VACUUM Adjustment Dial VACUUM Interval Timer Manual INPUT JACK Time Set Button Timer Display CCW CW Fix S W Guide Lock Tube Guide Roler Head Tube Holder Electric Code Out Signal Remote Signal Input Hand S W Bottle Holder Fix Pin 656 253 Seongsu lga Seongdong gu 133 821 Korea Led Lamp signals that the switch is on A Remote Control Mode when operating LED flickers Time range 99 99 sec Continuous Operation Adjust the deposit size 0 10 VOLUME The liquid cutting mechanism after ending of discharge operation Adjustable within 0 3 sec Finger FOOT S W plug To fix liquid outlets 0 01
4. ified tube for the roller e The socket outlet shall be installed near the equipment and shall be easily accessible e If the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired e When installing the controller please be careful not to prevent the ventilating openings on the side of controller Also any materials must not be filled in e Please be sure to turn off the power when you input the hand switch to the controller _ 656 253 Seongsu lga Seongdoneg eu 133 821 Korea ye RAN cEnK
5. nger Foot S W to start operation 656 253 Seongsu lga Seongdong eu 133 821 Korea ye RAN cEnK 5 Additional Data 7 Pump Head Types SILICON TUBE ow eee E M Teflon Tube 0 3 x 0 6 0 5 x 1 0 S Teflon Tube 06x 1 1 0 7 x 1 2 Teflon Tube 0 9x1 5 2 4x 3 0 G Silicone Tube 05 25 6x 10 50 100 120rpm 50 100 120rpm 8 Environmental conditions for the equipment operation 6 Cautions and Reminders e Indoor use only e Use the nominal Voltage AC 220V 110V 50 60Hz e Altitude up to 2000 m e Don not remove the body cover e Temperature 5 C 50 e Do not remodel the body or any of its interior parts e Maximum relative humidity 80 e Do not touch the pump rolling parts and the rotor s inner parts while the pump is working i Bae eae ae e Mains supply voltage fluctuations not to exceed 10 of the nominal e Do not stick anything in the nozzle It may cause a crack in the tube or a liquid dispersion When inner rotor is stuck with liquids please send it immediately for repairing voltage e Do not place any unnecessary things on the body e Transient over voltage according to INSTALLATION CATEGORIES e The body should be placed on a working desk with a flat surface OVERVOLTAGE CATEGORIES II A nan ih POLLUTION DEGREE 2 i d ith IEC 664 e When move the body hold firmly with both hands en een Check if something oily or slippery is on the body or your hands are freasy when you move the unit e Do not use unspec
Download Pdf Manuals
Related Search