Operating Instructions
Contents
1. 12 Never disconnect the power cord by pulling or tugging on the cord 13 Avoid direct eye exposure to the LED light source while it is on 14 Never drink the haze smoke fluid 15 IMPORTANT the smoke aperture on the unit can get VERY HOT Never touch this area whilst the unit is in operation and always leave the unit to cool down before touching the area 1 Safety eyelet 8 Carry handle 2 LED On Off button 9 Timer remote interval adjust knob 3 Manual Fog button 10 Timer remote duration adjust knob 4 Fan speed regulator see below 11 Timer remote output level adjust knob 5 Controller connection 12 Timer remote manual overide button machine ready LED indicator 6 Power On Off button 13 Timer remote continous output button machine power LED indicator 7 IEC mains input 14 Timer remote On Off button timer active LED indicator Setup and operation 1 Unpack your unit then remove the tank 2 Unscrew the top cap of the tank 3 Fill the tank with haze smoke fluid do not over fill the tank 4 Screw on the cap securely Replace the tank into the unit 5 Check that the pipe is fed down towards the bottom of the bottle so that a consistent flow of fluid is supplied to the machine 6 Connect the timer remote to the rear of the unit 7 Connect the IEC mains cable to the rear of the unit and then to the mains power Turn the unit on using the Power on button 8 Heat up time is usually between 3 4 minutes Please e2. unit in a well ventilated area until the tank is almost empty Do not allow the pump to run dry Cleaning is now complete Refill with haze smoke fluid Run the unit briefly to clear any cleaning solution from the system Trouble shooting Symptom Solution Check mains power No Power Check external fuse Check internal fuse No smoke haze output Check fluid level Check timer remote Check if there is any blockage in the system Breaker fuse keeps blowing Possible electrical short Contact retailer distributor for further instructions Low smoke output Run a cleaning solution through the smoke machine Check that the smoke machine is plugged into the correct voltage Unit is not heating up Check the external fuse Check the internal fuse Possible faulty part Contact your retailer distributor for further instructions Remote control does not work Make sure connector is firmly connected to device Try using another controller Possible faulty controller Check the internal fuse Check the external fuse Specifications and features Model Kam KFHM1000 Power supply 230V AC 50Hz Power 1000w Fuse FSA Re heat time 2 3 minutes Output 8 000 CuFt per minute approx Tank capacity 2 5 litres Timer remote Yes LED FX Yes Gross weight 6 63kg
3. INSTRUCTION MANUAL KFHM1000 Powerful combined fog and haze machine with LED FX M A N U AL V E RS ION 1 0 18 10 13 Due to continuous product development please ensure that you have downloaded the latest instruction manual for this product from the Kam website at www kam co uk For the latest updates and information on the entire Kam range visit www kam co uk Kam products are manufactured by Lamba ple Unit 1 Southfields Road Dunstable Bedfordshire United Kingdom LU6 3EJ Telephone 44 0 1582 690600 Fax 44 0 1582 690400 Email mail lambaplc com Web www lambaplc com Made in China Due to continuous product development specifications and appearance are subject to change Copyright Lamba plc 2013 E amp OE AA ss BCE Thank you for purchasing this Kam product we are sure that it will serve you for many years to come To optimise the performance of this product please read these operating instructions carefully to familiarise yourself with the basic operations of this unit Please retain them for future reference This unit has been tested at the factory before being shipped to you To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture To prevent a fire hazard do not expose the unit to any naked flame sources Unplug this apparatus during lightning storms or if it is unlikely to be used for long periods of time When installing the unit please ensure you le
4. ave enough space around the unit for ventilation Slots and openings in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating To prevent fire hazard the Openings should never be blocked or covered The unit is powered by mains electricity always handle the power cable by the plug Never pull out the plug by pulling on the cable Never touch the power cable when your hands are wet as this could cause an electric shock Do not tie a knot in the cable The power cable should be placed such that it is not likely to be stepped on A damaged power cable can cause a fire or give you an electrical shock Check the power cord periodically if you ever find that it is damaged replace it before using the unit again Contact your retailer for a replacement The voltage of the available power supply differs according to country or region Be sure that the power supply voltage of the area where this unit is to be used meets the required written on the unit The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit s enclosure that may be of sufficient power to constitute a risk of electrical shock to persons Caution to prevent the risk of electric shock do not attempt to open the unit No user serviceable parts inside Refer all servicing to qualified service personnel The exclamation mark inside a triangle is intended to alert the user to th
5. d reservoir access and routine maintenance Safety cables must always be used utilising the provided safety eye bolt Never mount in places where the fixture will be exposed to rain high humidity extreme temperature changes or restricted ventilation General maintenance To maintain optimum performance and minimise wear the item should be cleaned frequently Usage and environment are contributing factors in determining the cleaning frequency As a general rule fixtures should be cleaned after use to avoid dust build up and blockages which can result in poor performance overheating and breakages Be sure to uplug the unit from the mains before conducting any maintenance Use a vacuum and a soft brush to remove dust collected on external vents and internal components Clean the external case when the unit has completely cooled down with a dry cloth or tissue Regular maintenance Be sure to power off fixture before conducting any maintenance Every 40 hours of continuous operation it is recommended to run a cleaning solution composed of 80 distilled water and 20 distilled white vinegar through the system to prevent the accumulation of particulate matter in the heating element The recommended cleaning regime is as follows 1 Empty all haze smoke fluid from the machine 2 Add the above cleaning solution to the tank 80 distilled water and 20 distilled white vinegar 3 Plug the unit in to the mains and allow it to warm up 4 Run the
6. e presence of important operating and maintenance instructions in the literature accompanying the appliance Select the installation location of your unit carefully Avoid placing it in direct sunlight or locations subject to vibration and excessive dust Do not use the unit where there are extremes in temperature below 41 F 5 C or exceeding 95 F 35 C Unpacking and safety Please unpack your new product carefully Your new product should reach you in perfect condition Please check that no damage has occurred during transit If any damage is found do not operate your unit Please contact the retailer you purchased it from immediately If there is any damage to the mains cable do not use the device Always disconnect the unit from the mains supply when carrying out any cleaning of the unit Power supply Use the plug to connect to the main power supply with the following connections Wire Connection Brown Live Blue Neutral Yellow Cyan Earth ams A CE Manufacturer declarations In compliance with the following requirements RoHS Directive 2002 95 EU and WEEE Directive 2002 96 EU If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal CE declaration of conformity R amp TTE Directive 1999 5 EU EMC Directive 2004 108 EU Low Voltage Directive 2006 95 EU The declarations are available on application from certification lambaplc com Before putting the devices in
7. nsure no button is pressed during the heat up time 9 When the machine is ready the LED light on the remote control will illuminate 10 Turn the output to Max and press the green button on the remote control for 5 seconds so the fluid has a chance to flow through the heater block making it ready to use 11 After completing the above adjust the settings on the unit to find the output level you desire The Manual fog button on the rear of the unit has priority over the controls on the Timer remote To use the Timer remote control functions you will need to release the Manual fog button on the rear of the unit Fan speed control amp fog haze The unit features a manually adjustable fan to regulate the amount of fog haze At it s heart the unit is a haze machine that can also produce fog effects As a general rule if you need to produce both fog and haze effects it is best to use haze fluid in the unit By using haze fluid both effects can be created If you wish to exclusively produce fog effects smoke fluid can used in the unit When alternating between the two different types of fluid always run the maintenance routines to clean the unit These are described later in this instruction manual To run the unit as a simple haze machine simply set the unit s output level so that it generates the amount of haze you require and then use a higher fan speed to disperse the effect thoroughly and evenly To create fog effects from the unit you
8. to operation please observe the respective country specific regulations Package contents 1 x fog haze machine 1 x timer remote control 1 x instruction manual this document 1 x mains cable Safety instructions Please read the following notes carefully because they include important safety information regarding this product 1 Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning 2 Do not install and operate the device in rain or extreme heat moisture or dusty environments 3 This device is for indoor use only and in a dry environment 4 If the device has been exposed to drastic temperature fluctuations do not switch the unit on immediately but wait until it reaches room temperature 5 Do not shake the device and avoid brute force when installing or operating 6 Do not use the device during thunderstorms Disconnect the unit from the mains 7 Do not use solvents or aggressive detergent to clean the device Use a soft clean cloth 8 Do not modify the device or the connected power cord 9 In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact your Authorised Kam Retailer Always use the same type of spare parts 10 Never connect the device to a dimmer pack 11 Make sure the power cord is never crimped or damaged
9. will need to reduce the fan speed this then lessens the dispersment of the effect and allows the fog to gather in a denser grouping Fan speed is increased by clockwise rotation of the Fan speed regulator on the rear of the unit and decreased when turning the knob anti clockwise The fan speed cannot be controlled using the Timer remote Timer remote control mode You can adjust the interval gap between each release between 0 30 mins approx using the Timer remote interval adjust knob 9 You can adjust the duration the effect is released at each interval between 0 15 seconds approx using the Timer remote duration adjust knob 10 For best results select continuous and adjust output to achieve desired effect note it can take around 30 seconds for the machine to produce the correct output Fuse Replacement Unplug the IEC power cable before replacing the fuse Always replace with same type of fuse 1 Using a flat head screwdriver remove the fuse holder from the IEC housing 2 Remove the bad fuse from the fuse holder 3 Insert the new fuse into the fuse holder 4 Install the fuse holder in the IEC housing Mounting Orientation This fixture should only be mounted used on a flat surface This fixture should not be tilted Rigging It is important never to obstruct the vents pathways Mount the fixture using a suitable C or O type clamp When selecting installation location take into consideration the flui
Download Pdf Manuals
Related Search