AFP1100 / AFP1200 Fast Ethernet 100Base
Contents
1. 2m Hub to Hub 412m Full duplex Switching Hub Node to Node 2km Node to Hub 2km Hub to Hub 2km For connecting to Router Bridge or Switching Hub please refer to the device s Technical Manual 6 Diagnostic LEDs amp Boot ROM The Link LED lights when fiber cable connection is good and the Act LED blinks to indicate the activity Collision and full duplex LED report the board s operating status To add the Remote Boot feature to a workstation insert the Boot ROM into socket as shown below Align the notch and pins on the Boot ROM with the notch and pin receptacles on the ROM socket Gently push the Boot ROM into the socket being careful not to bend the pins Boot Rom Socket Notch PROM Fig 1 Diagnostic LEDs and Boot ROM Socket 7 Technical Specifications Standard EEE 802 3u Fast Ethernet 100Base FX e Connector AFP1100 SC Tx Rx multi mode connectors AFP1200 ST Tx Rx multi mode connectors e Cable Fiber 50 125 62 5 125 100 140 um multi mode e Data Transfer Mode Speed PCI bus master Full or half duplex Default mode 100Mbps speed Link ACT COL and FDX LEDs on the bracket Power Requirement 2 0A 5V Ambient Temperature 0 to 50 C Humidity 5 to 90 PCB Dimensions 123 x 80 mm LxH Emission FCC Part 15 Class A amp CE Mark2. AFP1100 AFP1200 Fast Ethernet 100Base FX User s Manual 9802 REV D1 1 Checklist Before you start installing the AFP1100 1200 verify that the package contains the following items AFP1100 1200 Board LAN Driver Diskette This User s Manual Please notify your sales representative immediately if any of the aforementioned items is missing or damaged 2 Overview AFP1100 1200 is a PCI Fast Ethernet Board that fully complies with all IEEE 802 3u 100Base FX standards Four LED indicators LINK ACT COL and FDX on the bracket will help to oversee the network board link activities collision and full duplex status 3 AFP1100 1200 PCI Configuration For motherboards with automatic PCI configuration No specific setup is needed You can enter the system BIOS setup menu to view or specify the interrupt line of the PCI slots For Motherboards with bus master amp interrupt jumpers Enable bus master operation in a selected PCI slot and select an interrupt IRQ level using the appropriate motherboard jumper Enable I O on the AFP1100 1200 PCI slot 4 PCI Bus System amp Configuration e Ensure that the PCI machine does support master slots INT multiple sharing and timing compatibility Do not install AFP1100 1200 in PCI slave slots Please refer to your PCI system manual and select the appropriate configuration settings e When installing multiple AFP1100 1200 boards at the server stati
3. on you should correctly configure the IRQ settings of the PCI slot Up to four AFP1100 1200 boards can be installed in a PCI file server running NetWare system The AFP1100 1200 server boards share the same interrupt line with the driver supporting multiple INT services at a time Each AFP1100 1200 s IRQ should not conflict with that of other board e Operation in full or half duplex Default mode is configured by LAN driver options The operating mode should match the remote link device s working status e You must use EMM386 version 4 49 or higher and install both DOS amp EMM386 that came from the same DOS package to avoid software problems 5 Network Connection 100Base FX TX network allows 512 bit time delay between any two node stations in a collision domain The Fiber TP cables with devices bit time delay round trip are as below 100Base FX 100Base TX DTE lt gt DTE 100 DTE lt gt DTE 100 Class I1 Hub 92 Class I1 Hub 92 Fiber Cable 1 00 m Cat 5 TP Wire 1 12 m DTE FX to DTE TX 100 100 Base FX to 100 Base TX Converter 56 The overall bit time of Fiber TP wires and devices must be within 512 bit in a segment You may use Switching Hub to break up collision domain and extend the cabling distance e Fiber Cable multi mode Limitations Half duplex Class II Hub Node to Node 205m Node to Hub 100m Hub to Hub 5m Half duplex Switching Hub Node to Node 412m Node to Hub 41
Download Pdf Manuals
Related Search