800 User Manual - Alarm Products Of Oklahoma
Contents
1. e To arm with zone s shunted first check the green STATUS lamp to make sure that no peri meter zone is in trouble Then press the SHUNT button labeled S and enter your code The yellow SHUNT light and the red ARMED MEMORY light will come on The green light will be out The SHUNT light will go out when you disarm the Control Center Alarm with the system disarmed If an alarm signals at a time when your system is not armed an alarm is occurring on a 24 hour protection zone or your standby battery is low The cause of the alarm must be corrected and then the Control Center reset by arming and disarming again in order to clear the signal Consult vour Alarm Plan to determine which if any of your protection zones are 24 hour instant protection Your alarm specialist may have installed an optional switch that may be used to cancel the exit entry delay period at the time of arming the system Use this fea ture when at home to sound an instant alarm upon intrusion through the exit entry door Activate the switch prior to arm ing Be sure to restore the switch to the normal position disarm the system and then re arm the system if you are leaving the premises Panic alarm To activate a panic alarm and call for outside help press the two buttons marked and on the Digit Key keypad Make sure you press both buttons at the same time he panic zone is capable of sending asilent sign2. an alarm occurred while you were gone Disarm the system with your code from the geet to silence the sounder TE If your system has a digital com municator there may be a delay while it is reporting an alarm before your system disarms If the red ARMED MEMORY light was flashing before you disarmed it will go out briefly then begin to flash a number of pulses identifying the zone s that had an alarm Write down the number of times the alarm memory lamp flashes so you will have a record of which zone s need attention You may then arm and disarm to cancel the flashing alarm memory If a zone is still in alarm condition you will hear the Mini Sounder for three seconds The red ARMED MEMORY light will go out The PROTECTING YOUR PREMISES WHILE YOU ARE AWAY leat STATUS light may start ashing if zones are still in trouble from the alarm If there was an alarm and the red ARMED MEMORY light did not flash the alarm was a 24 hour zone see your Alarm Plan The cause of the alarm will have to be removed before you can clear the alarm signal PROTECTING YOURSELF WHILE YOU ARE ON PREMISES Arming with zone shunting You might have chosen one or two zones that you can man ually shunt out of the system from the keypad A shunted bypassed zone cannot cause an alarm Zone shunting may be used for turning off interior protection or allowing you to turn on only your perimeter protection JHH E
3. If your alarm specialist installed smoke detectors or heat sensing thermostats you have 24 hour fire protection This optional Fire Pro tection Zone is always active even though your system may be dis armed An optional Fire Supervision and Indicator Station on the Control Center provides the following fire circuit controls AC Power Check If the yellow AC light on the Fire Supervision and Indicator Station is off the Control Center is not receiv ing AC power Press the spring loaded SILENCE 8 FIRE RESET switch toshut off the Mini Sounder Check lights to see if there is a general power outage If there is vou will be operating from your standby battery When AC power is restored the Mini Sounder will come back on Press the spring loaded switch again to silence the Mini Sounder Fire Zone Check The Mini Sounder on the Fire Supervision and Indicator Station signals a problem on the Fire Zone Press the spring loaded SILENCE 8 FIRE RESET switch toshutoff the Mini Sounder The red TROUBLE light will come on until the Fire Zone is cleared When the zone is restored the Mini Sounder will signal again to indicate that the Fire Zone is functional Press the SILENCE amp FIRE RESET switch once again to turn off the Mini Sounder Fire Detector Reset After a fire alarm the red FIRE ALARM light will be on Press the SILENCE 8 FIRE RESET switch to clear the smoke detectors Alarm Battery Test The fire alar
4. Key keypad and enter any combination of numbers up to 6 digits there is no zero Use a number you will remember such as your birthday 12 s 47 rather than something obvious like your address The numbers you choose become the only code recog nized by your system Return to the Control Center and slide the switch to the RUN position YOUR SECURITY system WILL NOT OPERATE IN THE LOAD POSITION USING YOUR SECURITY SYSTEM Using your code to arm and disarm the system Once you enter your personal code into the Napco Digit Key keypad the red ARMED MEMORY light will go on to show the Control Center is armed and off to show it is disarmed If you enter the wrong code your alarm system will fail to respond Be sure to WAIT 5 SECONDS before attempting to re enter your code Changing your code Slide the switch into the LOAD position Enter a new code into the Digit Key keypad Return the switch to the RUN position REMINDER When arming or dis arming if the red light does not respond you may have entered the wrong code Wait 5 seconds before trying to enter your code again When entering your personal code for the first time or reentering your code after an extensive power failure enter the code again after moving the switch to the RUN position his will activate the keypad lights and arm the system PROTECTING YOUR PREMISES WHILE YOU ARE AWAY Arming the system before you leave First check
5. the green STATUS light at the keypad or keyswitch If this light is on stead ily enter your code The red ARMED MEMORY light will come on and the green lamp will go out Leave immediately through the entry exit doorway before the delay time runs out If you delay too long in leaving the premises you will hear the Mini Sounder warn you that the exit delay time has run out To avoid causing an alarm quickly return to the keypad and enter your code to reset the Control Center You may then re arm and try to exit again Arming with a zone In trouble When the green STATUS light is flashing one or more of your burglary protection zones are in trouble and incapable of being armed The green light will flash the number s identifying the zone or zones in trouble For example if your back door is open on Zone 1 and a window is open on Zone 3 the green STATUS lamp will flash once for Zone 1 pause then flash three times for Zone 3 Refer to your Alarm Plan for zone locations Look for something you can fix yourself in the area protected by the zone s in trouble In this example you can fix the zones yourself by closing the back door and the window If the zone cannot be fixed immediately the green light will continue to flash Try to arm If the zone s in trouble have been programmed as Auto Shunt zones the red ARMED MEMORY lamp will come on the green light will go out and
6. to mitigate the possibilities of harm and or damage NAPCO is not an insurer of either the property or safety of the user s family or employees and limits its liability for any loss or damage including incidental or consequential damages to NAPCO s original selling price of the product regardless of the cause of such loss or damage If the user wishes to protect itself to a greater extent NAPCO will at user s sole cost and expense obtain an insurance policy to protect the user supplemental to user s own policy at a premium to be determined by NAPCO s insurer upon written notice from user by Certified Maii Return Receipt Requested to NAPCO s home office address and upon payment of the annual premium cost by user Some states do not aliow limitations on how long an implied Warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages or differentiate in their treatment of limitations of liability for ordinary or gross negligence so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state ASO TOO MELEE METEOR ESTEE EEE EIEN ANAC USTEST SOS VIS SS AS SUST MTU determined by kraj the SASS off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient the receiving antenna i relocate the computer with respect to the receiver move the com
7. who use the building 1 Ifthe premises is a residence sleep with the bedroom door closed A closed door will hold back deadly smoke while you escape 2 When the fire alarm signals escape guickly Do not stop to pack 3 Test the door If it is hot use your alternate route through the window If the door is cool brace your shoulder against it and open it cautiously Be ready to slam the door if smoke or heat rush in Crawl through smoke holding your breath Close the doors again on leaving to help prevent the fire from spreading 4 Go to your specific outdoor meeting ag so you can see that everyone Is safe 5 Assign someone to make sure nobody returns to the burning building 6 Call the fire department from a neighbors telephone Central Station Service Person optional feature Telephone Telephone NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS INC NAPCO warrants its products to be free from manufac turing defects in materials and workmanship for fifteen months following the date of manufacture NAPCO will within said period at its option repair or replace any product failing to operate correctly without charge to the original purchaser or user This warranty shall not apply to any equipment or any part thereof which has been repaired by others improperly installed improperly used abused altered damaged subjected to acts of God or on which any serial numbers have been a
8. TACE RA OPERATING GUIDE FOR YOUR MAGNUM ALERT 800 800 S lt SECURITY SYSTEM You have taken a major step in protecting your home or busi ness by dle a Napco Magnum Alert 800 800S Alarm Control Center installed Please read this guide thor oughly to familiarize yourself with your new security system Keep this booklet handy for future reference Note especially the ALARM PLAN on page 15 Your alarm specialist will help you fitt it out and explain the various fea tures and operating procedures for your new Magnum Alert 800 8008 CONGRATULATIONS GLOSSARY OF TERMS Abort Delay A delay period that allows the system to be reset before it reports to a central station Alarm Plan Identifies the areas of your premises pro tected by each zone of protection and lists zone features see page 15 Disarming Turning ponr tern ON or OFF This can be done by en emg a code on the D igit Mid steypa or by turning an optional key switch Arm Disarm Personal Code A code of up to six digits which is used to arm and disarm the system from the key pad Standby battery is placed in the Control Center box to provide backup protection in the event of a power lose Centrai Station Monitors incoming burglayand emer gency messages ftom a Digital Communi cator and alerts the proper authorities optional feature Control Center The heart of the Magnum Alert 800 800S security system it cont
9. al to the Central Station when a Digital Communicator is being used optional The Panic Alarm is always active whether your system is armed or not PANIC ALARM TEAR HERE USING THE DIGITAL COMMUNICATOR Your Alarm Specialist may have programmed your security system to be monitored by a Central Station The built in digital communicator can trans mit emergency signals to the Centmi Station 24 hours a day EMERGENCY SERVICES MONITORS YOUR Police Medical Etc SYSTEM 24 HOURS EMERGENCY SERVICES NOTIFIED UPON ALARM CONDITION FAST RELIABLE RESPONSE MAGNUM ALERT 800 800S DIGITAL COMMUNICATOR 11 12 A Abort Delay Note which zones on your alarm plan have abort delay This is a 16 second delay that enables you to reset the system before a zone condition report is sent to the Central Station Non 24 hour zones however must first be repaired Central Station Ri The Central Station will ac knowledge the fact that you have armed your system by ringing back with a short beep of the Mini Sounder COMMUNICATOR FEATURES Opening and Closing Reporting An optional feature that per mits the Central Station to receive a signal each time the system is armed disarmed or both TEAR HERE FIRE PROTECTION The following information is applicable only where local ordinance permits use of your alarm Control Center for fire detection Controlling Your Fin Circuit
10. dental consequential or otherwise arising out of any failure of the product Setler s warranty as hereinabove set forth shall not be enlarged diminished or affected by and no obligation or liability shall arise or grow out of Seller s rendering of technical advice or service in connection with Buyer s order of the goods furnished hereunder NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY Warning Despite frequent testing and due to but not limited to any or all of the following crimina tampering electrical or communications disruption it is possible for the system to fail to perform as expected NAPCO does not represent that the product system may not be compromised or circurnvented or that the product or system will prevent any personal injury or property loss by burglary robbery fire or otherwise nor that the product or system will in all cases provide adequate warning or protection A properly installed and maintained alarm may only reduce risk of burglary robbery fire or otherwise but it is not insurance or a guarantee that these events will not occur CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING Therefore the installer should in turn advise the consumer to take any and all precautions for his or her safety including but not limited to fleeing the premises and calling police or fire department in order
11. even if the loss or damage is caused by the seiler s own negligence or fault This warranty contains the entire warranty it is the sole warranty and any prior agreements or representations whether oral or written are either merged herein or are expressly cancelled NAPCO neither assumes nor authorizes any other person purport Ing to act on Its behalf to modify to change or to assume for It any other warranty or liability concerning its products E OCS ht Cnn nk Ta TT TATA TTT THE FOLLOWING STATEMENT Is REQUIRED BY THE EFCC This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception it has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference wili not occur in a particular installation H this equipment does cause interference to radio of television reception which can be Napco Security Systems 333 Bayview Avenue Amityville NY 11701 in no event shall NAPCO be liable for an amount in excess of NAPCO s original selling price of the product for any joss or damage whether direct indirect inci
12. ltered defaced or removed Seller will not be responsible for any dismantling or reinstallation charges In case of defect contact the security professional who installed and maintains your security system NAPCO shail have no obligation under this warranty or otherwise if the product has been repaired by others improperly installed improperly used abused altered damaged subjected to accident nuisance flood fire or acts of God or on which any serial numbers have been altered defaced or removed NAPCO will not be responsible for any dismantling reassembly or reinstallation charges in order to exercise the warranty the product must be returned by the user or purchaser shipping costs prepaid and insured to NAPCO After repair or replacement NAPCO assumes the cost of returning products under warranty There are no warranties express or Implied which extend beyond the description on the face hereof There is no express or Implied warranty of merchantability or a warranty of fitness for a particular purpose Additionally this warranty is in Heu of all other obligations or ilabilities on the part of NAPCO Any action tor breach of warranty including but not limited to any implied warranty of merchantability must be brought within the six months foliowing the end of the warranty period In no case shall NAPCO be liable to anyone for any consequential or incidental damages for breach of this or any other warranty express or implied
13. m bell siren and standby battery should be tested weekly Disarm the Control Center Push the BATTERY amp BELL TEST switch down and listen to the bell siren If the alarm sounds weak the battery is faulty Call for service Would You Like More Safety information For information on home fire de tection burn safety and home fire safety contact the National Fire Protection Association Public Affairs Dept OSA Battetymarch Plaza Quincy MA 02269 NOTE If there is no Fire Supervision and Indicator Station on your Control Center and your Fire Zone uses smoke detectors have your alarm specialist show you and explain the switch he has installed for resetting the smoke detectors after an alarm 14 Preparing an escape plan Even with the most advanced fire alarm system adeguate pro tection reguires an escape plan To braw te your plan raw floorplans of your build ing see sample Show two exits a front or back door and a window from each room Make sure the window works You may need a special fire escape ladder if the window is high up Write down your outside meeting place Rehearse 1 Everyone in their room with the doors closed 2 One person sounds the alarm 3 Each person tests his door 4 Pretend the door is hot and use the alternate escape exit 5 Everyone meet outdoors at the assigned spot FIRE ESCAPE PLAN IMPORTANT Read Carefully Discuss these escape procedures with those
14. puter away from the receiver plug the computer into a different outist so that computer and receiver are on different branch circuits if necessary the user should consult the dealer or an experienced radioftelevision tech nician for additional suggestions The user may find the following booklet prepared bythe Federal Communications Commission helpful How to identity and Resolve Radio TV interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 PEE TTT PTTL TEST TE PRAT OR CER LRT EER R RRR ERT eRe ee eee aos
15. rols all system functions Digital Communicator Reports eu 04 and emergencies directly to the central station over telephone lines ni Keypad Napco s Digit Key keypad puts Control Center functions at r fingertips It can be mounted either atthe Control Center or anywhere in your premises Exit Entry Delay Lets you exit and enter your premises without setting off an alarm after the system is armed Mini Sounder Buzzer at each Digit Key keypad warns that entry delay time is In progress It also sounds when you attempt to arm the foil if a particular zone is in trouble It also verities contact with a central station optional Panic Buttons Two buttons and ud on the Digit Ke keypad which will alert the Central Station of an emergency A communication sent to a Central Station indicating a specific change in condition of the security system alarm trouble low battery etc Optlonai Labeled on the Digit Key keypad Lets ou manually remove one or more pro ective zone from the system Zones Independent circuits that protect specific areas pu premises Auto Shunted Zone A zone capable of being automaticalty bypassed shunted out of the ection system ir it is in trouble faulty whem yau aitempit to arm the_system Burglary Zone Detects intrusion one A zone programmed to cause audible optional indication at the Digit Key keypad when it is in trouble during the di
16. sarmed period Group Shunt Zones A group of zones programmed so they can be manually by passed shunted all at once Priority Zone When a zone selected for the feature is in trouble it will be impossible to arm the Control Center Trouble Zones Zones that cannot be armed because of an open window door or other problem in the area 24 Hour Zones Are always armed and ready at all times to respond to an emer gency situation DIGIT KEY KEYPAD CONTROLS indicator Lights Armed Memory Light Red e Steady system is armed e Flashes system is in alarm Count the number of flashes to tell in which zone the alarm occurred Example Fourflashes alarm in Zone 4 Status Light Green e Steady system is disarmed all zones okay e Flashes zone in trouble in capable of being armed Count the number of flashes to deter mine zone s Example Four flashes trouble in Zone 4 shunt Light Yellow e Steady one or more zones are shunted bypassed from the system Mini Sounder e When you enter your premises the tone reminds you to reset the Control Center before the end of a timed entry period so you do not activate the alarm The Mini Sounder also sounds if you attempt to arm the system when a particular zone is in trouble Els Faceplate of Digit Key keypad lifts up to reveal convenient ref erence index of zones protected UNDERSTANDING YOUR SECURITY SYSTEM Each securit
17. y system is custom tailored to the owner s needs but all MAGNUM ALERT 800 800S have the following 1 Zones Your system contains up to six separate zones Each zone is an independent circuit that pro tects specific areas of your home For example your alarm spe cialist may have set aside a zone for window protection exit entry delay interior dee protection safe and valuables protection or emergencies Each zone can be programmed to react in a specific manner Check and be certain that you know what each zone protects 2 The Digit Key Keypad or optional key switch Lets you perform the following functions arm disarm the system check the status condition of each zone temporarily shunt re move individual zones from the system and send an emergency alert to a Central Station optional 3 The Alarm Output When any zone is activated the Control Center responds by sounding an audible alarm and or alerting a central station optional Your alarm specialist has programmed your system to react in a specific manner to each type of emergency Be sure you understand how your system responds to these emergencies Selecting your personal code If your system includes the Napco Digit Key keypad you can choose your own private code to arm and disarm the Control Center To program your code slide the switch upper left hand corner of your Control Center into the LOAD position Go to the Digit
18. your system will be armed The sounder will come on for 4 sec onds to remind you that you armed with one or more zones shunted turned off When you try to arm with a zone programmed as a Priority Zone in trouble the Control Center will not arm Enter your code again to silence the sounder If you cannot fix the zone call your alarm specialist Check the Alarm Plan in this manual to remind you which zones are programmed as Prior ity zones and which are Auto Shunt The Alarm Plan will also indi cate which zones if any can be manually shunted Manually shunt with caution Shunting too many zones will leave your prem ises unprotected even with your system armed To arm with zone s manually shunted count the flashes on the green STATUS light to be sure the zone in trouble is capable of being manually shunted Press the SHUNT button labeled S and enter your code The yellow SHUNT light and the red ARMED MEMORY light will come on The green light will be out All zones programmed by your alarm spe cialist to respond to manual shunting will be shunted even if some are not in trouble Leave quickly when the red ARMED MEMORY light goes on Be sure to have all zones in trouble repaired as soon as possible Disarming when you return When you enter through the exit entry door the entry delay Mini Sounder will come on Check the red ARMED MEMORY light If it is flashing
Download Pdf Manuals
Related Search