XHBL Series VARTECH - VarTech Systems Inc.
Contents
1. XHBL Series 34 150 120 CONTACT Vartech Systems Inc 11529 Sun Belt Ct Baton Rouge LA 70809 Phone 225 298 0300 Toll Free 800 223 8050 Fax 225 297 2440 Email sales vartechsystems com www vartechsystems com XHBL Series 35 150 1202. Touch Screen applications all Monitors must be con nected to the computer before installing the TSHARC driver A If installing RS 232 connectors the drivers have to be installed for each T S or If installing USB connectors the drivers install once for multiple Touch Screens If the T S connector is USB the Window O S loads a temporary USB driver wait for the driver to load caution Boot up the computer Insert the User CD On the desktop left double mouse click on the My Computer icon Locate the drive with the User CD Left mouse click to open 10 Left mouse double click to open the Touch Screen Driver folder 11 Left mouse double click to open the file for the O S on the computer File 2000 XP 8 SE ME or File WinNT and 12 Left mouse double click to run set up exe Annan XHBL Series 23 150 120 TSHARC Installation bb ec S 1 At the Welcome screen select Next to go to the End User s Software License Agreement EULA 2 After reading the EULA if in agreement check the box I accept all of the terms Figure 15 3 Select Next ie il Be Vg Me oter Hope rer Poms ole ere eee PLN ILEI VEAR TAL LE SAULE Tesi LEE ASF AT Te FS ee zn Sate arier In In Bu lieg F ds wen Gum Zeg en lee a en AH not in agreement follow instructions and Exit Cesbe zs KS ey PT pe ER Teen FS AAT m sms ET GET BE ET ie Se enge BITT L EET perena m paa bar Note Any unlawful use of the TSHARC d
3. be completely removed before installing the TSHARC Note The typical driver uninstall program or Microsoft s remove program utility does not remove all tracks of a T S Driver installation Contact the manufacturer of the previously installed driver program to learn how to completely uninstall their product These instructions may be available from the manufacturer s web site Touch Screen Installation TSHARC Touch Screen Controller Driver The TSHARC T S Controller Driver files are on the User CD in the shipping box There are two driver files Select the driver compatible with the O S on the computer Before loading the Touch Screen Controller driver verify the COM ports are enabled especially if connecting to a laptop computer caution Installation 1 Verify the T S Cable is connected to the Monitor or attach the T S Cable s 5 pin connector to the Monitor s 5 pin connector 2 Figure 7 Attach the T S Cable s RS 232 connector to the computer serial COM port where the T S will be installed or 3 If the T S was ordered with a USB connector insert the cable to the computer USB port where the T S will be installed and 4 If the optional USB Pass through was ordered attach the T S Cable s other split end connector the USB to a computer USB port N Note For Multi monitor Touch Screen applications all Monitors must be connected to the computer before installing the TSHARC driver For Multi monitor XHBL
4. connec tors engineered to provide a safe and secure dust and waterproof environment in rugged conditions Summary of NEMA 6P IP 68 Enclosures constructed for indoor or outdoor use to pro vide a degree of protection to personnel against incidental contact with the enclosed equipment to provide a degree of protection against falling dirt against hose directed water and the entry of water during occasional prolonged submersion at a limited depth and that will be undamaged by external formation of ice on the enclosure APPENDIX D Technical Specifications TFT AM SVGA LCD 256K Display Colors 800 x 600 pixels 700 nits Sunlight 800 nits Transflective AR AG Transflective Readable Dimming Ratio Video Input RGB and NTSC PAL B D G I K IP68 Fischer High Density to DB 15 Connectors JAE to Flying Leads DC Input JAE to DB Touch optional JAE to USB Port optional Milled Aluminum Black Anodized Panel Mount or RAM Mount Power 6 Watts Min 20 Watts Max Consumption Wide Range 3 30 vpc DC P Ee 12 24 28 VDC nominal Internal Short Circuit Protection Power Load Dump Protection Conditioning Over Voltage Protection Reverse Polarity Protection XHBL Series 33 150 120 Environmental Specifications Operating Temperature Operating Tempature w Internal Heater Option Storage Temperature 50 G IP Rating IP68 NEMA 6P Submersible Designed to meet FCC B CE me e fete
5. dropped or damaged or e Exhibits a distinct change in performance indicating a need for service Shipping If the unit should need to be shipped to the VARTECH Service Center the original packing material should be used to insure safety of the unit in shipping Repack the unit as it would have originally been received from VARTECH XHBL Series 5 150 120 PRODUCT CARE AND MAINTENANCE Product Care This XHBL Monitor has been designed to provide optimum performance and service without any required scheduled maintenance other than occasional cleaning Disconnect the Monitor from the power source before cleaning the Monitor optional Touch Screen or unit s enclosure warning e Do not use abrasive cleaners or solvent based flammable cleaners on the Flat Panel or Touch Screen Display its enclosure or any other electrical caution device cables power cord etc e Do not use paper products as they may scratch the display screen and e Do not directly apply cleaning solutions to the display screen Display Screen Cleaning e A vinegar based cleaner is preferred to prevent streaking and degradation of the coatings or e A non abrasive glass cleaner such as a professional foam glass cleaner e Apply the cleaning solution to a soft clean cloth dampening slightly e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and e To minimize the risk of abrasion to the scr
6. e Press the SELECT button to enable the OSD dialog box Zoom feature e Press the RIGHT button to go to Exit and e Press the SELECT button to save and Exit or Exit without making changes factory Reset e Press the SELECT button to Exit and return all OSD settings to factory defaults OPTIONAL INTERNAL HEATER Optional Internal Heater The optional Internal Heater automatically brings the Monitor up to the standard operating temperature if the unit is below that temperature when powered on Operations e The flashing blue LED lights behind the Operator Control Buttons indicate the unit is in the heating mode bringing the Monitor up to operational temperature e Once the Monitor is up to operational temperature the flashing blue LEDs become a constant blue glow and the unit automatically powers on e Maximum time for the unit to reach operational temperature is approximately 12 minutes and e There are no User adjustments for the Internal Heater function XHBL Series 20 150 120 OPTIONAL NVIS fILTER Optional NVIS filter The optional Night Vision Imaging Systems NVIS filter on all VARTECH Monitors is in compliance with the NVIS radiance value requirements of MIL STD 300 and MIL L 85762A for Type 1 Class B electro optical displays This means the NVIS filter is compatible with Night Vision Goggles NVG OPTIONAL USB PASS THROUGH CONNECTOR Optional USB Pass Through Connector The optional USB Pass through Connector signal
7. is sent through the Touch Screen T S cable connection to the computer e Install the IP68 sealed T S 5 pin connector to the Monitor s rear pod 2 Figure 7 e Install the T S cable s USB connector to any computer USB port Note Do not install the RS 232 Serial Connector It is inactive T S is not installed e Install the IP68 sealed 4 pin 6m 2 ft VARTECH USB Pass through Cable to the Monitor s rear pod 1 Figure 7 and e The USB Pass through Connector on the other end is standard A type USB port socket and is not sealed A The USB port socket on the cable is not sealed caution Optional USB Pass Through Connector with Touch Screen Display The optional USB Pass through Connector signal is sent through the Touch Screen T S cable connection to the computer e Install the IP68 sealed T S 5 pin connector to the Monitor s rear pod 2 Figure 7 e With the split end of the T S Cable install the USB connector to any computer USB port e Install the other end the Touch Screen Display RS 232 Connector to a computer serial port or e Install the other end the Touch Screen Display USB Connector to a computer USB port e Install the IP68 sealed 4 pin 6m 2 ft VARTECH USB Pass through Cable to the Monitor s rear pod 1 Figure 7 and e The USB Pass through Connector on the other end is standard A type USB port socket and is not sealed A The USB port socket on the cable is not sealed caution XHBL Series 2
8. local installation codes Safety Icons lt Warning Shock Hazards This icon is intended to tell the User of a potential risk of electrical shock warning lt Caution Instructional This icon is intended to tell the User of important operating and or maintenance instructions caution General Unit Safety e Always disconnect the unit from the power source before cleaning e Do not operate the unit with a damaged cord e Do not operate if the unit has been dropped or damaged The unit should be inspected by qualified VARTECH Service Personnel e Position the power cord so it is not in contact with hot surfaces e Do not allow anything to rest on the power cord and e Do not place the power cord in the path of foot traffic AN General Safety Precautions warning Power cord must be connected to a properly wired and grounded power source Any equipment to which the unit is attached must also be connected to properly wired and grounded power sources Do not connect or disconnect the unit during an electrical storm Do not remove the unit covers there are no user serviceable parts in the unit Do not disassemble or modify the unit to avoid the possibility of electrical shock damage to electrical components or scratching the display surface and Disassembly of the unit voids the warranty XHBL Series 4 150 120 ER fluids from LCD Display caution e If the Monitor should ever become shattered do not touch fl
9. removing all TSHARC drivers Other Touch Screen Drivers must be uninstalled with their manufacturer s uninstall utility File Qewndaad Ka from the VARTECH Web Site The TSHARC uninstall utility may be down loaded from www vartechsystems com Go WE engere to the Support tab gt Drivers gt TSHARC em mme DEE eek 98 Driver Uninstall Utility gt TSUN10 exe a m Fu Fu mar ee L re Beet a To download the utility left double mouse click on the file name gt At the File Down d ie Hes hewn at bento a esl sarat les man psi load dialog box select Save Figure 14 gt Jun Save the file to the computer s program l files gt Make a new folder TSHARC Unin figure 14 stall gt Select Open gt Save the TSUN10 exe file gt At the dialog box Download is complete select Open Folder gt Left double mouse click on TSUN10 exe to execute the utility At the dialog box Do you want to remove select Yes gt At the dialog box Press OK to complete the uninstall select OK gt At the uninstall confirmation screen select OK Follow the instructions The dialog box stating it is removing all Touch Screen Drivers from the computer means it is removing all TSHARC drivers Other Touch Screen Drivers must be caution uninstalled with their manufacturer s uninstall utility XHBL Series 22 150 120 Previous Versions of Other Manufacturers Touch Screen Drivers If a different T S Controller Driver not TSHARC is on the computer it must
10. viewing set to auto configurate Image Width Press the RIGHT or LEFT button to adjust the width and Press the SELECT button to save and Exit or Exit without making changes Phase Adjustments Press the RIGHT or LEFT button to adjust the signal phase in the analog to digital converter and Press the SELECT button to save and Exit or Exit without making changes H Position e Press the RIGHT or LEFT button to adjust horizontal position of the display and e Press the SELECT button to save and Exit or Exit without making changes V Position e Press the RIGHT or LEFT button to adjust the vertical position of the display and e Press the SELECT button to save and Exit or Exit without making changes XHBL Series 19 150 120 Miscellaneous OSD Dialog Box Control OSD Duration e Press the RIGHT or LEFT button to adjust the time elapse between the last menu activity and when the menu disappears Factory default is 15 seconds and e Press the SELECT button to save and Exit or Exit without making changes OSD H Position e Press the RIGHT or LEFT button to adjust the horizontal position of the OSD menu on the display and e Press the SELECT button to save and Exit or Exit without making changes OSD V Position e Press the RIGHT or LEFT button to adjust the vertical position of the OSD menu on the display and e Press the SELECT button to save and Exit or Exit without making changes OSD Screen Zoom Setting
11. 1 150 120 OPTIONAL TOUCH SCREEN DISPLAy XHBL Optional Touch Screen Installation If installing a new operating system O S do not install the Touch Screen Controller Driver until the O S is installed and the computer s video display caution Settings have been verified see section Computer Display Settings The Touch Screen Controller Driver uses the computer s O S display driver settings to accurately configure the Touch Screen Controller Driver files Previous Versions of Touch Screen Controller Drivers Previous versions of ANY Touch Screen Controller Driver must be removed before installing the latest version of the TSHARC Touch Screen Controller Driver caution Uninstall TSHARC Drivers Utility Uninstall a Previous Version of the TSHARC Driver The uninstall utility TSUN10 exe is included on the User CD gt Touch Screen Driver gt TSHARC Driver Uninstall Utility in the shipping box with the product accessories This utility uninstalls TSHARC drivers only from the Product CD To uninstall install the CD gt go to My Computer desktop gt Left double mouse click gt Locate the drive with the Installation CD gt Left mouse click to open gt Left double mouse click on the Uninstall Drivers folder gt Left double mouse click on TSUN10 exe to execute the uninstall utility gt Follow the instructions Note The dialog box stating it is removing all Touch Screen Drivers from the computer means it is
12. Monitors installed on the system Figure 20 2 Using the keypad or the mouse select the Monitor to calibrate 3 Switch to the Calibration tab Go to the next section Calibration and 4 When complete return to the Screen Selection tab in sequence select the next Monitor Repeat the process until all Monitors are calibrated XHBL Series 26 150 120 harma auer Crtrei Ferries Li E Leg Lg gg ka Leg Vik emp eegal figure 21 figure 20 1 To customize the calibration process select the Calibration button to bring up Calibration Options and the Offset menu Figure 22 2 Select OK when calibration and or offset selections are made aT e Three Point Calibration A quick calibration of a K L eeng known good T S overlay with no correction applied e Four Point Calibration Compensates for skew and some edge linearity anomalies e Seven Point Calibration More accurate than three point calibration No correction is applied e Twenty Point Calibration Provides the highest level of T S linearization and skew correction I ima Catei Tagh e Offset Varied linearity exists between T S types User may want to calibrate the edges of the T S on more precisely Default is 20 figure 22 XHBL Series 21 150 120 Calibration Process 1 Press the Center Graphic to start calibration Figure 23 e 2 Targets are used to calibrate the Touch Screen Follow the on screen instructions Touch the target c
13. OMI ea tal Ce zeegt Kin ED ed mb Meal fs Ee figure 17 XHBL Series 24 150 120 Manual RS 232 Controller Set up LEO 8 1 Select the Controller Interface RS 232 button BRENNEN enerne Figure 18 WR T Fol er bal Pal pear boosh renee weal cpr br 2 Select Next u Note Do not select Autodetect Wekre Frk an Cf 3 3 Enter the COM port selection Rochas 4 The T S Controller baud rate default is TE ege 600 andl rm ig 2 Note This is a Resistive T S display The Capacitive och e saiten Controller option is not available 5 Select Next 6 Following installation select Finish and 7 Reboot the computer when prompted Do not select Autodetect if manually setting up the Touch Screen COM port caution Enable Touch Screen Tray Icon Wie 1 If the User wants a T S Controller tray icon ur Em nn associated with the Display Rotational Menu to aa show in the toolbar tray select the box Figure 1 and Sen 2 Select the Finish button the TSHARC driver is a re installed figure 19 Disable Touch Screen Tray Icon XHBL Series 25 150 120 If the User does not want a T S Controller tray icon Calibration to show in the toolbar tray select the Finish button The calibration process aligns the the TSHARC driver is installed T S overlay to specific points on the display Installation Complete screen At the dialog box Set up is now complete select OK exiting the TSHARC T S Controller 1 Select
14. Solutions for Demanding Applications SE a7 SYSTEMS INC XHBL Series 6 4 10 4 12 1 15 1 User s Guide Read instructions completely before attempting to operate your Display Information Disclaimer This VarTech Systems Inc publication is provided as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or merchantability and fitness for a particular purpose Documentation Change Notice The information in this publication is subject to change without prior notice in order to improve readability and reliability as well as design and function These changes shall be incorporated in a new revision available from the product and or download section of the VARTECH web site www vartechsystems com Liability In no event shall VARTECH be liable for direct indirect special incidental or consequential damages arising out of the use of or the inability to use VARTECH s product or its documentation even if advised of the possibility of such damages Endorsement Product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective companies Copyright This document contains proprietary information protected by copyright All rights are reserved No part of this manual in whole or part may be reproduced by any means in any form without prior written permission of Vartech Systems In
15. a right click by holding down a touch Ge Es e point for a specific time period ZE Use the slide bar to set the Right Click Delay value to the time necessary to produce a right click event Double Click Area This step sets the area that allows for a double click event Limit this to areas that may be accurately touched several times Use the slide bar to set the double click area the box displays the activator size Double Click Speed 1 Use the slide bar to set sufficient time to perform a double touch in specified area 2 Select the Apply button to enter the selection and 3 Select the OK button to apply all Click Settings me se figure 26 XHBL Series 28 150 120 Touch Settings Normal EE Emulates a standard mouse allowing a single click pater double click drawing dragging and right click option hoe if enabled Figure 27 St Haan Touch Down Allows for a click event to take place at touch down No draw or drag is available Touch Up Touch only Double click is disabled If right click was earlier enabled it is now disabled e figure 27 Touch Sound 1 Check the Enable Touch Sound to enable a tonal beep when the screen is touched 2 Select the Apply button to enter the selection and 3 Select the OK button to apply all Touch Settings Capacitive Tab Disabled The T S is a Resistive type the Capacitive Tab is disabled Syncronized Touch Screen with Third Par
16. c Table of Contents GE 4 Product Care and Maintenance 6 EE eet 8 eee de JE 9 Cable Connections en es 11 Optional AC Power Adanter ennenen ernennen reren nnnnne 12 Computer Hook up cece ce eeeceeeeeeeeeeaeaeaeeeneeeeees 13 lef den d EE 15 On Screen Display OD 16 Optional Internal Heater cc cece eee cceceeeecececeeeeeeeeseeaeeeeeees 20 Optional NVIS TI dE 21 Optional USB Pass through Connector ararnrvnnnnnvnnnnnnnnnnnnnnvnvnnn 21 Optional Touch Screen Display 22 Appendix A Mechanical Drawings 2 ecececeseseceeeeeeeeeeeeenens 30 Appendix B Troublesbootng nenne nnnnnnnnnnnn 30 Appendix C NEMA and IP Industry Standards 32 Appendix D Technical Environmental Specifications 33 SAfETy General Safety Instructions e Before operating the XHBL Monitor read this User Manual thoroughly e Keep this User Manual for future use e Verify computer capability see System Set up to insure operation of the Monitor eFor expeditious installation follow these User Manual instructions in sequence e Adhere to all Caution and Warnings on system and as stated in this User Manual e User Manual instructions for installation and operation should be followed precisely e Adjust only those controls covered by the User Manual s operating instructions improper adjustment of other controls voids the unit s warranty and may result in unit damage and e Adhere to
17. d Display has rolling bars across the screen or vertical shaded bars on the image ossible Problem ms 70 0 10 Defective video cable On a known good display source confirm the video cable is not defective Interference from adjacent equipment For proper grounding and shielding verify use of a proper video cable Keep the cable away from sources of EMI such as electric motors or unshielded RFI sources such as radar and microwaves Horizontal size is not adjusted In the OSD adjust the horizontal size control Symptom Picture quality image stability is distorted ossibie Froblem olution Not working in 800 x 600 pixel resolution or Verify computer video display Is set at 000 x 1024 x 768 pixel resolution 600 pixels 1024 x 768 pixels Proper cable grounding and shielding Verify the use of a proper video cable with suitable grounding and shielding Keep the video cable away from sources of EMI and RFI Improper video display settings Check signal source for a proper signal Verify computer video display is set at 800 x 600 pixels 1024 x 768 pixels Verify the display refresh rate 60 75Hz Display unit is farther than 3 m 10 ft from Single cable lengths in excess of the standard signal source 3 m 10 ft cable should be of high quality shielded VGA cable Contact VARTECH for information on custom cables Multiple Monitors are driven from the same Splitting the video signal divides the stre
18. e D r ah EE S ll WW ree Ek el Za al ach 7 Select the Monitor tab 8 Under Monitor Settings verify the Screen Refresh Rate is set at 60Hz Figure 11 e If so select the Cancel button and go to step If not select 60Hz and figure 11 e Select the Apply button XHBL Series 13 150 120 9 At the Monitor Settings dialog box select Yes to accept the new desktop view Geesen I DL fi Gr Hj skoten Dace settings Figure 12 Geen Leen Mantes pen Wantan Lotte X 10 In the Display Properties dialog box verify the Tar nt han be smed De ym warn han Screen Resolution is set at 800 x 600 pixels a E SVGA r Brae Pil r k 11 Select the Apply button i 2 12 At the desktop screen shutdown the computer 13 Turn off the monitor and 14 Disconnect the monitor from the computer figure 12 Power on the Monitor e Connect the XHBL to the computer e Power up the XHBL e Power up the computer e The Windows Operating System should automatically apply the best generic driver for this connection USER TIP XHBL Series 14 150 120 OPERATOR CONTROLS On the right hand side of the Monitor bezel are six Operator Control buttons Figure 13 POWER ON Off Button Note Monitor defaults to an AUTO OFF state when power is applied e The POWER ON OFF button is marked with the I O Input Output symbol e Momentarily pressing this button turns ON or turns OFF t
19. een air drying is recommended Optional Touch Screen USER TIP The Touch Screen Display may be activated when cleaning This may create a potentially dangerous condition power down disconnect cabling prior to cleaning warning Touch Screen Cleaning e Use a special screen cleaning tissue or a solution specifically formulated for antistatic coatings Follow the manufacturer s instructions or e Lightly dampen a soft clean cloth with water or a general purpose mild detergent solution e Keep a fresh side of the cleaning cloth towards the screen surface to avoid scratching it with accumulated grit and e To minimize the risk of abrasion to the screen air drying is recommended Monitor Enclosure e Clean the unit enclosure with a soft clean cloth lightly dampened with a general purpose mild detergent solution e Wipe down with clean water and e Dry with a soft clean cloth XHBL Series 6 150 120 T Long term Storage e For long term storage it is suggested the unit be stored in a normal indoor environ ment and the display glass be protected from accidental damage e For pedestal mount units disconnect the cable s and loosen the arm adjustment to a point where the ball can be removed from the arm or e For Flush or Panel Mount units cover the product with a protective covering that will not scratch or transfer any dyes to the display screen Maintenance Doe ea eee AN Power Cord warning To avoid shock and f
20. enter hold until it shrinks then release the target and 3 Repeat the process for all targets Note Calibration screen returns to the Calibration tab if the first point is not touched within 10 seconds Calibration Verification Test were 1 Touch the screen in several places to verify the Calibration Target is displayed under the finger and 2 Select the Accept button to apply and record the calibration data Figure 24 Note If Calibration Target is not displayed under the finger select the Cancel button repeat Custom Calibration Settings then Calibration Process Calibration Drawing Test figure 24 1 Select the Test button on the Calibration tab 2 Using a finger or stylus draw or write Figure 25 3 Observe if screen displays the drawing accurately If it does not repeat the Custom Calibration Settings and Calibration Process instructions and 4 When satisfied select the Quit button to exit Fi Click Settings PE Right Click figure 25 BE If desired for T S application check the Enable Right Click box to set the right click option Figure 26 Right Click Area u F Use the slide bar to set the T S event area to a TIE EE size slightly larger than the activator larger for ohn we gt a finger tip smaller for a stylus the box displays ha gt Ke the activator size ar nese aa Right Click Delay IL ler zu CS The timed hold right click mouse event allows the ien oo User to initiate
21. ess function parameters it is recommended the LCD panel backlight be set to its brightest LARGE SUN button in the ambient light source use the Brightness control buttons to adjust e Press the RIGHT or LEFT button to set the display s desired brightness and e Press once the SELECT button to save changes Contrast Contrast is the difference in brightness between the light and dark areas of the pixels of a picture e Press the RIGHT or LEFT button to set the display s desired contrast and e Press once the SELECT button to save changes Black Level Black Level adjustment intensifies or decreases the display s saturation of black e Press the RIGHT or LEFT button to set the display s desired black level and e Press once the SELECT button to save changes Audio Volume Adjustment Menu Audio Volume Adjustment is not available on this Monitor series XHBL Series 17 150 120 Color Adjustment Menu Auto Color e Press the SELECT button to run the Auto Color Set up Note screen flicker e A new dialog box pops up with highlighted Happy and Sad Faces e Press the SELECT button to choose the Happy Face if present Auto Color is accept able or using LEFT button choose the Sad Face if unacceptable and e Press the SELECT button to save the changes or not save if Sad Face was chosen and Exit e Press the SELECT button to allow the OSD to automatically set Standard Color e A new dialog box pops up with high
22. he flying leads to the cor responding polarity on the DC voltage source primary terminal figure 8 Verify the polarity of the power source posts prior to attaching the power cable s flying leads warning OPTIONAL CONNECTORS epuonal USB Pass through Connector The optional USB Pass through Connector is an IP68 sealed 4 pin connector e The custom USB Cable is with the product accessories it is 6 m 2 ft e Line up the red dots to 1 in Figure 7 and e Plug together e To disconnect pull the outside ring on the connector away from the unit until free Optional Touch Screen Connector e The optional Touch Screen Connector is an IP68 sealed 5 pin connector e The connector is between the S Video and Power Connector e The Touch Screen Cable is in the shipping box it is 3 m 10 ft e Line up the red dots to 2 in Figure 7 and e Plug together OPTIONAL AC POWER ADAPTER Optional AC Power Adapter e The optional AC Power Adapter Cable Set consists of a 3 m 10 ft cable with an IP68 sealed connector the power adapter and a 1 8 m 6 ft common AC power cord Figure 6 The adapter accepts voltage from 110 to 250 VAC and frequency from 47 to 63Hz The AC power cord plug is a North American standard for 120 VAC 60Hz and Line up the red dots to 3 in Figure 7 To disconnect pull the outside ring on the connector away from the unit until free Note The optional AC Power Adapter is not an off the shelf item It is equipped w
23. he unit and e A Red LED located under the I O button glows when the unit is powered on Optional feature The Monitor defaults to an AUTO ON state when power is applied This feature must be ordered when the Monitor order is placed It is not available after the unit is built Brightness Buttons figure 13 These buttons control the brightness of the LCD panel display e The LARGE SUN button when repeatedly pressed or held down causes the display s LCD panel backlight brightness to be stepped up in increments to its brightest setting e The SMALL SUN button when repeatedly pressed or held down causes the display s LCD panel backlight brightness to be stepped down in increments to its lowest setting which is just above total black suitable in very subdued light as in night time operations and e Adjusted settings are maintained when the unit is powered off then powered on USER TIP SELECT Button The SELECT Button is the access point to the On Screen Display OSD Source Screen Function Menu See On Screen Display Press the SELECT button twice to access the Video Source Menu to move between video inputs Composite and S Video RIGHT Button The RIGHT Button is an adjustment tool in the On Screen Display OSD Source Screen Controls Menu See OSD Screen Control Menu Categories LEfT Button The LEFT Button is an adjustment tool in the On Screen Display OSD Source Screen Controls Menu See OSD Screen Cont
24. ighlight bar through the related Functions Menu Press once the SELECT button to activate the highlighted Functions Menu item Create the new value adjustment controls are the RIGHT and LEFT buttons which increase or decrease the value of the parameter as indicated in the display bar Press once the SELECT button to save the new value this returns the user to the display screen or wait 15 seconds and the OSD will close saving all changes To choose another Display Category use the RIGHT or LEFT button to move across the Source Screen Menu repeat above instructions or Use the RIGHT or LEFT button to move across the OSD Menu to highlight the last icon the Exit Door press once the SELECT button to exit the OSD Menu Upon Exit all changes are saved e New settings are stored in memory upon pressing the SELECT button to exit the Source OSD Source Screen Category s Function Menu caution e f SELECT is not pressed or inactivity is detected within the 15 second factory default OSD duration any function adjustments made will be saved XHBL Series 16 150 120 OSD Source Screen Menu Parameter Selections Video Signal Input Menu The Video Signal Input menu is preset No changes may be made There is a checkmark beneath Box 1 representing the analog VGA computer signal being altered into a digital signal on the LCD display x USER TIP Brightness Contrast Black Level Menu Brightness Before adjusting the Brightn
25. ire hazards replaced the unit s power cord if e Insulation becomes damaged or e A loose connection is suspected Other Maintenance Only VARTECH Qualified Service Personnel should perform all other maintenance except for cleaning and the power cord replacement described above To avoid risk of electrical shock do not disassemble the unit s enclosure Users cannot service the Monitor User maintenance is restricted to cleaning warning Or power cord replacement as explained Disassembling the unit voids the warranty XHBL Series 7 150 120 SYSTEM SET UP System Requirements The computer the XHBL is connected to must have this capability e Video card setting with a minimum resolution of 640 x 480 pixels and e If the optional Touch Screen Display is ordered an available COM or USB port for the connector is required depending on the display connector style ordered Shipping Box Contents The XHBL is shipped in a custom box with custom foam packaging It is recom mended the installer save the box and all packaging materials in case the unit would need to be returned to the VARTECH Service Center The shipping box contents are e XHBL unit e Power Cable e VGA Cable e Mounting System and Hardware e Touch Screen Cable if optional Touch Screen Display is ordered e USB Cable if optional USB Pass through is ordered and e User CD XHBL Series 8 150 120 INSTALLATION The XHBL is designed to be mounted in three co
26. ith a specific connector for integration with the XHBL monitor XHBL Series 12 150 120 COMPUTER HOOk UP Computer Display Properties SVGA or XGA Prior to connecting the XHBL to the computer connect the computer to a monitor to verify the computer video display properties are set to 800 x 600 SVGA pixels e The optimum setting for viewing is 800 x 600 pixels SVGA e The screen refresh rate must be set at 60Hz to minimize flicker and screen split caution Pixel settings above the recommended setting exhibit fractured images Refresh Setting the Display Settings Arrange Icons By 1 Right mouse click on an open area of the desktop screen to bring up the Desktop Menu Geh Undo Move Chi 2 Left mouse click on Properties to open the Graphics Properties Display Properties menu Figure Graphics Options New 3 Connect to a monitor to establish the computer display properties Properties Display Proper lies ES fig ure 9 Themes Desklop Screen Saver Appearance Settings 4 Select the Settings tab 5 Under Screen Resolution verify or slide the bar until the Screen Resolution is at 800 x 600 pixels SGVA or 1024 x 768 pixels XGA Figure 10 os et teen hea 6 Select the Advanced button to go to gaar ear Eau the next menu to verify the Hz refresh Ku J Minie leghe Je be rate 800 by 600 gie ania ee Sia Wi F ti Leet JL Advanced LD JL Gees Jl ve figure 10 fn pagr
27. lighted Happy and Sad Faces e Press the SELECT button to choose the Happy Face if present Auto Color is accept able or using LEFT button choose the Sad Face if unacceptable and e Press the SELECT button to save the changes or not save if Sad Face was chosen and Exit Standard Color Set up RGB Color Temperature Settings Color Adjustments e Press the SELECT button to go to the RGB Red Green Blue Color Temperature Settings Menu e Use the RIGHT or LEFT button to select one of the five Temperature settings and e Press the SELECT button to save the changes and Exit or Exit without making changes RGB Color Skin Tone Adjustment Best accomplished if viewing a screen shot with skin tone prior to adjusting e Use the RIGHT or LEFT button to adjust the Color Skin Tone and e Press the SELECT button to save the changes and Exit or Exit without making changes RGB Color Hue Adjustment Hue is the pinks blues and greens of the display e Use the RIGHT or LEFT button to adjust and e Press the SELECT button to save the changes and Exit or Exit without making changes XHBL Series 18 150 120 RGB Color Saturation Adjustment Saturation is the vividness or intensity of the hue or color e Press the RIGHT or LEFT button to set the display s desired saturation and e Press the SELECT button to save the changes and Exit or Exit without making changes Image Setting Menu Auto Configuration e For optimal display
28. m No light behind button LEDs Possible Problem Solution No power loose power connection Confirm the Monitor is properly connected to a DC or AC power source Verify the power source is live or try another battery or AC power outlet Verify the Monitor is powered on Reverse polarity Check polarity of the power connection Symptom Light behind button LEDs no display or No Signal error message and or no image on the displa Possible Problem Solution Power on no video signal Verify the video cable is plugged into the VGA video connector Verify a video signal is coming out of the computer i e plug into a known good display source Verify the incoming signal source selected matches the Monitor signal source Composite S Video VGA Check the Brightness front panel LCD adjust ment on the Monitor This may be set too low Check the Brightness and Contrast controls in the OSD These may be set too low Computer may have gone into power manage ment stand by Press any key on the keyboard move the mouse or cursor or if there is a Touch Screen touch to wake the computer Symptom Display has rolling bars across the screen or vertical shaded bars on the image Possible Problem Solution VGA video display is not set to view at 800 x Verify computer video display is set at 800 x 600 pixels or 1024 x 768 pixels 600 pixels 1024 x 768 pixels XHBL Series 14 150 120 Symptom continue
29. nfigurations with a universal ball and socket mounting kit in a Flat Panel or optional Flush Mount configuration Pedestal Mount The XHBL is shipped with a RAM universal ball and socket system mounting kit Figure 2 By installing the Monitor with this kit the User can adjust the viewing angle to improve viewability in changing environments This ball and socket system has proven to be successful in supporting an extreme amount of weight in high vibration and difficult mount applications Locate the ball and socket system in the shipping box The kit consists of two RAM balls on mounting plates and a RAM arm with an adjustable T knob and a packet of three 3 M4 x 10 counter sunk stainless screws for mounting to the XHBL Figures 2 4 figure 2 Panel Mount Only figure 3 figure 4 XHBL Series 9 150 120 There are three mounting holes in the back of the Monitor for the attachment of a ball mounting plate Take care not to strip the screw holes or over tighten Figure 4 It is recommended the remaining ball be mounted on a flat surface Because of the various surface substrates where the Monitor is to be mounted the installer provides the screws to mount the other ball e Note the location of the three mounting holes on a ball mounting plate Figure 4 With three 3 M4 x 10 counter sunk stainless screws Figure 3 attach mounting plate to the back of the XHBL Figure 2 e Mount the second ball mounting plate on the s
30. ngth signal source of the signal A video signal booster line driver is recommended if installation requires more than one Monitor driven from a single video source Monitor has incorrect or bad sync signals Check for proper video cable installation or replace suspected faulty cable Verify computer video display is set at 800 x 600 pixels 1024 x 768 pixels and at a 60 75Hz refresh rate image is not perly sized Possible Problem Solution OSD adjustments need to be made Adjust the vertical and horizontal size controls through the OSD Symptom Displa Improper video display settings Verify computer video display is set at 800 x 600 pixels 1024 x 768 pixels and at a 60 75Hz refresh rate XHBL Series 31 150 120 Symptom Touch Screen T S does not respond Possible Problem T S cable is not plugged in Verify the connections between the T S and the computer T S cable is installed in a different COM port Install the T S into another COM port If using than installed by the software a laptop verify the COM port s is enabled T S Controller driver has not been installed Install the TSHARC Controller driver Hardware failure Contact a VARTECH Technical Support Technician Symptom T S moves but does not follow a finger or stylus Possible Problem olution Solun T ontroller is not calibrated Run the calibration in the TSHAR ontrol Panel software T S Controller Driver is not installed Install the TSHARC Co
31. ntroller Driver T S cable is not installed correctly Verify the T S cable is installed correctly Possible Problem Solution Uninstall the driver using UN10 exe If a correctly previous T S Controller Driver was installed all footprints must be removed Go to the T S manufacturer s web site or contact the manu facturer for instructions to uninstall driver Reinstall the TSHARC Driver software APPENDIX C NEMA and IP Industry Standards There are two major electrical manufacturing organizations monitoring product enclosures and or their degree of protection each organization also publishes tech nical manufacturing standards The National Electrical Manufacturers Association NEMA Standard No 250 2003 addresses non hazardous locations enclosure design and its environmental performance requirements These are referred to as NEMA Types www nema org The International Electrotechnical Commission IEC 6052 Standard addresses Ingress Protection IP this describes the degree of enclosure protection provided not the enclosure itself The first digit of the IP Code designation describes the degree of protection against the ingress of solids the second digit designates the degree of protection against the ingress of liquids IP Codes support NEMA Type designations www iec ch VarTech Systems designs the XHBL sealed monitor to exceed the Stand ards of NEMA 6P and IP68 incorporating a range of environmentally sealed
32. river is a strict violation of the United States and International copyright laws Using a TSHARC driver with any third party Touch Screen is strictly prohibited s gg En ee F ei dee gee FT fe mr Gees figure 15 Select Controller Note A PS 2 Controller Interface is not available Sek Ca Hiei 1 The TSHARC Driver is a 12 bit Controller the radio button is selected by default 2 Select the Controller Interface matching the cable used to install the XHBL serial or USB 3 Select the Autodetect button if installing the T S through a RS 232 serial Interface 4 There are two options for RS 232 installation Autodetect and Manual Manual instructions are found in section Manual RS 232 Controller Set up Figure 16 a JJ zl 5 If connecting through a USB Interface select figure 16 the USB radio button 6 Select Next 7 Following installation select Finish and 8 Reboot the computer when prompted keet est k l Te Te eel ege a iF H Autodetect RS 232 Controller Set up 1 Select the Autodetect button TII 2 The AutoDetect Serial dialog box lists the wins E detected RS 232 Controller information Select MIEL el m OK Figure 17 3 Installing Touch Screen Driver text box pops up indicating the progress of the installation 4 Following installation select Finish and 5 Reboot the computer when prompted Laser Tags Us Mb Ler T T DE NEE DA EEN Ss re icity D
33. rols Menu Categories 17 XHBL Series 15 150 120 ON SCREEN DISPLAy The On Screen Display OSD User Interface is where display signal source adjust ments are made The Source Screen Menu with its user friendly graphical interface provides access to fine tuning the display OSD Source Screen Menu Activation To activate the OSD menu in the current video source press and release the SELECT button Note OSD Source Screen Menu closes after 15 seconds of inactivity This setting can be adjusted in the OSD Source Screen Menu Miscellaneous under OSD Duration OSD Source Screen Menu Categories The Source Screen Menu is comprised of six icons plus the Exit Door icon with each icon representing distinct source screen categories and their corresponding functions menu with adjustable settings General Instructions for functions Menu Adjustments e To open the OSD Source Screen Menu press once the SELECT button Use the RIGHT or LEFT button to move across the OSD Source Screen Menu to select the OSD Source Screen Display Category As each Category icon is highlighted its related Functions Menu appears in the lower section of the dialog box To activate a Display Category with the RIGHT or LEFT button move the highlight box over the Category s icon Press once the SELECT button to choose the highlighted icon In the Functions Menu a highlight bar is superimposed over the first function Press the RIGHT or LEFT button to move the h
34. s to be mounted Take care not to strip the screw holes or over tighten caution as the enclosure is aluminum XHBL Series 10 150 120 CABLE CONNECTIONS Cables e The XHBL is packaged with two cables Use care when inserting or VGA and DC Power 1 and 2 in Figure 5 caution removing connectors e The AC Power Adapter is optional Figure 6 1 VGA Input 2 DC Power Input figure 5 Connectors Connectors are located on the bottom of the unit housing from left to right VGA Optional USB Pass through Optional Touch Screen and Power Figure 7 Connectors are physically unique to insure the installer makes the proper connections Optional USB Input Optional Touch Input Power Input VGA Input figure 7 VGA Connector e The IP68 sealed VGA Cable 3 m 10 ft is in the shipping box e Line up the red dots on the connectors e Push the cable connector into the Monitor s back panel connector 4 in Figure 7 e Plug the standard DB 15 video female connector to the computer s video source XHBL Series 11 150 120 DC Power Connector The IP68 sealed DC Power Cable 3 m 10 ft is in the shipping box e Line up the red dots to 3 in Figure 7 Plug in the quick connect 3 pin connector e To disconnect pull the outside ring on the connector away from the unit until the cable is free e The positive flying lead is marked with a label The negative lead is not marked Figure 8 e Connect t
35. the Calibration tab or in installation ten seconds the calibration program launches unless a Multi monitor situation is TSHARC Calibration Program _ _ _ _ present then go to section _ Upon reboot the T S is functional but not Configuring a Multi monitor calibrated Calibration must be configured for the Installation Figure 21 T S to work properly The TSHARC Control Panel 2 There are three buttons initiates the calibration process Graphic Calibration and Test For default Four point e Go to Start gt Programs gt Hampshire TSHARC calibration select the Graphic Control Panel The Control Panel square This is the best known has several tabs Each tab provides links to tools general calibration it that modify the TSHARC Driver to compensates for skew and meet specific needs some edge linearity anomalies e Touch Screen Display Selection and e Calibration 3 Go to section Calibration e Click Settings Process e Touch Settings Capacitive Settings disabled Custom Calibration Settings Note The XHBL is a Resistive Touch Screen the Capacitive Setting is disabled TSHARC Control Panel Screen Selection Note If this is not a Multi monitor installation skip to section Calibration Configuring a Multi monitor Installation Note Microsoft does not support a Multi monitor installation in Windows 98 SE 1 The Controller installation program opens to the Screen Selection tab Note the graphic representation of the
36. ty Display Rotation Drivers The T S may be set to automatically rotate when the display is rotated by third party Display Rotation Drivers 1 Right click on the System Tray icon and 2 From the TSHARC Rotation Control Panel Menu enable select Autodetect Rotation Presetting Autodetect Rotation Parameters To synchronize the T S with the display map the T S rotation with all the user required display rotations 1 Verify Autodetect Rotation is enabled 2 Rotate the display to all rotations needed using the third party Display Rotation program 3 Apply the changes and 4 Touch the target displayed by the TSHARC driver Note User should only need to synchronize the Touch Screen with the Display Rotation Drivers one time USER TIP ee e Windows 8 SE ME and 2000 supports only two orientations at any one time User may rotate the screen from Landscape to Portrait mode caution in either direction User may not autodetect both Landscape and Portrait at the same time four orientations O 0 180 and 2700 e WinXP autodetects all four orientations O 0 180 and 270 XHBL Series 29 150 120 APPENDIX A Mechanical Drawings Mount diagrams of the XHBL and its dimensions may assist with the installation of the Monitor Optional flush Mount Bezel Mount diagrams of the Flush Mount Bezel and its dimensions may assist with the installation of the Monitor APPENDIX B Troubleshooting Sympto
37. uids from the LCD display e If fluid should get on hands or clothing immediately wipe off with liquid soap or rubbing alcohol on a clean towel wash with water immediately consult with a doctor and e If fluid gets in the eyes flush eyes immediately with water for a minimum of 15 minutes immediately consult with a doctor Electrical Connecting Cables e Disconnect the power to the computer when the Monitor is being installed and e Upon installation verify the power connector is securely seated on the unit Power Source This unit may be operated from an AC optional or DC standard power source e Use the supplied power cable and e Always connect to a properly grounded power source EE EMI Rfl caution This product has been engineered to meet or exceed international industry standards addressing product design and enclosure protection against EMI RFI when installed with the factory provided cables Protection on Servicing Servicing User e User product servicing is limited to cleaning the unit e Do not disassemble or modify the unit to avoid the possibility of electrical shock damage to its electrical components or scratching the display surface and e Disassembly voids the warranty Servicing VARTECH Qualified Service Personnel may be required if the unit e Does not operate normally when installation instructions are followed e Does not operate normally when operating instructions are followed e Has been
38. urface where the Monitor is to be installed e Insert each ball into the RAM arm e Lightly tighten the arm around the balls using the T knob on the arm Figure 2 4 e Adjust the Monitor to the viewing preference and e Tighten the T knob to hold the Monitor in position Panel Mount The Panel Mount installation should be specified at the time of order the ball and socket mount system will not be included in the shipping box For installation there are four tapped mounting holes on the four corners of the unit s rear panel The mounting hardware packet is included with the product accessories in the shipping box This packet includes four 4 M4 stainless steel threaded studs 8 6 cm 3 long four 4 Nylock self locking nuts and four 4 flat washers Take care not to strip the screw holes or over tighten caution as the enclosure is aluminum flush Mount with Optional Bezel With the Flush Mount Bezel the XHBL Flat Panel Display may be mounted flush with the mounting surface the ball and socket mount system or any mounting hardware will not be included in the shipping box The installer needs to supply screws for this type of installation When the placement site has been decided it is recommended the installer use these measurements when cutting the opening for the Monitor s installation Note the locations of the milled holes in the Flush Mount Bezel Drill corresponding holes into the substrate where the Monitor i
Download Pdf Manuals
Related Search