CV7_Operator Manual_GB
Contents
1. Rivet de fixation 180 SUD Fixing rivet SOUTH The CV7SF is compatible with the Directive 1999 5 CE R amp TTE Copyright 2014 LCJ CAPTEURS User manual Receiver with cable and USB connector 4 USE INN DIN Plug the USBcable to the PC The driver will automatically be installed by the Windows system Windows 7 and above Alternatively the latest version of the driver can be downloaded from the technical support section of the website www lcicapteurs com It is an executable file Double click on the file to launch the installation Once the CV7 is connected to the USB port your relevant software Will immediately identify the NMEA0183 sentences via an emulated COM port 17 5 DIMENSIONS 371 mm 212. ULTRASONIC WIND SENSOR LCJ CAPTEURS User manual 4imm 371 mm Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 5 CV7 C 5 1 CONTENT OF DELIVERY CV7 sensor With vertical carbon arm 25 m cable A mark below the sensor indicates the alignment The vertical bracket is designed for mounting on a horizontal surface usually the mast head on a sailing boat For mounting on the side of the mast an additional bracket is available separately See section 12 2 The CV7 C sensor must be installed with the Nord mark on the bracket aligned to the geographical North for a fix installation on shore Rivet de fixation Fixing rivet Copyright 2014 LCJ CAPTEURS CV7 STANDARD User manual Bracket Weight 200 gr Sensor arm bracket 371 mm 760 mm ULTRASONIC WIND SENSOR LCJ CAPTEURS 6 CANBUS OPTION 6 1 TYPICAL INSTALLATION OVEVIEW CV7 C s gt CANBUS baa BG i NMEA 2000 The CanBus option is compatible with all CV7 sensors Connectors are not supplied 6 2 CONNECTIONS The CV7must be set for NMEA0183 interface factory set The CV7ultrasonic sensor is powered by the bus network Open the Junction box to access the connectors OOOO Green Yellow Blue Red CV7 V O Barometer The CanBus option allows connecting a CV7 to any instrument system featuring a NMEA2000 compatible interface PGNs sent by the option 5
3. E CANBUS RM mast angle sensor p ni NMEA 2000 The CanBus RM option is compatible with all CV7 sensors Connectors and mast angle sensor are not supplied 7 2 CONNECTIONS Open the junction box to access the connectors QOOO QOOQO Green Yellow Blue Red 12VDC OV Can L Shield Can H CV7 V BUS gF07 Q P AO Bi a 681 S1 Cursor Josuas ajsuy 1SEN O Barometer With the RM option the CanBus junction box features an extra connection terminal for the mast angle sensor potentiometer PGNs sent by the option 59392 60928 126464 126996 130306 130311 130314 PGNs processed by the option 59392 59904 60928 Power consumption 2 LAN 7 3 COMMISSIONING Refer to the connected instruments manual for pages setup and all functions related to wind and atmospheric pressure functions Once all wiring and connections are completed turn the power on and check the alignment It may be adjusted from your instrument s setup menu Alternatively this can be done directly from the CanBus Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 7 4 CALIBRATION OF THE MAST ANGLE SENSOR MID SHIP AND MAST ANGLE ENDS Use the and keys to change a value that is previously selected with the switch button S1 In positions 3 to 6 the values read on the wind displays are the mast angles measures used for calibration of the mast angle sensor Calibration process Positi
4. CV7SF 16 1 CONTENT OF DELIVERY CV7SF sensor With vertical arm 16 2 INSTALLATION The CV SF Wind sensor IS designed tor operation outdoor exposed to natural light It must be installed in an area free from any air flow perturbation Choose a location free from any obstacle and situated at least 150 cm from the ground The radio signal maximum range is 200 meters Best results are obtained in a 50 meters distance between the sensor and its receiver The signal can be perturbated by materials such as carbon aluminium steel A minimum distance of 10 meters between the arm and any conductive material is recommended Specific environments may cause bad reception Please contact our technical support in that case 16 3 SENSOR ALIGNEMENT A mark below the sensor indicates the alignment The vertical bracket is designed for mounting on a horizontal surface usually the mast head on a sailing boat For mounting on the side of the mast an additional bracket is available separately see section 12 2 The CV7 sensor must be installed with the Nord mark on the bracket aligned to the geographical North for a fix installation on shoreUse a compass taking the deviation in account NORD NORTH 16 6 Rivet de fixation 180 SUD Fixing rivet SOUTH The CV7SF is compatible with the Directive 1999 5 CE R amp TTE User manual Receiver 16 4 CONNECTIONS Open the receiver to access the connection terminal The NM
5. NMEA Input fromwww lIcjcapteurs com Refer to 15 2 Utilisation du logiciel de configuration or Display The CV7 sensor must be installed with the Nord mark on the bracket aligned to the geographical North for a fix installation on shore and to the bow on a vessel Fine alignment can be performed with the application configuration CV7 downloadable fromwww Icjcapteurs com 2 2 SENSORALIGNEMENT 6 Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 3 CV7 Standard 3 1 CONTENT OF DELIVERY CV7 with oblique arm 25 m cable Oblique bracket User manual B 2 SENSOR ALIGNEMENT ne ODII UE Dra S l Cd Q DE nou CQ O C horizontal surface It is usually fixed on the mast head of a sailing boat The arm points to the bow CV7 sensor view from below 3 3 DIMENSIONS ue 63 NG 330 mm 80 Copyright 2014 LCJ CAPTEURS 1 CV7 V 4 CV7 V 4 1 CONTENT OF DELIVERY CV7 sensor With vertical arm 25 m cable Bracket A mark below the sensor indicates the alignment The vertical bracket is designed for mounting on a horizontal surface usually the mast head on a sailing boat For mounting on the side of the mast an additional bracket is available separately see section 12 2 The CV7 V sensor must be installed with the Nord mark on the bracket aligned to the geographical North for a fix installation on shore Rivet de fixation Fixing rivet
6. alignment will be obtained with the calibration functions of your instrumentation or the LCJ Capteurs software calibration application see 15 2 When necessary install the interface junction boxes in a protected and dry location Run the cable down to the display s interface avoiding locations where other cables or equipment may produce electromagnetic interferences pilot s ram radio and cutit to the right length The cable s length can be adjusted as required providing junctions are made in the state of the art Turn the power supply off before processing to any wiring work You can turn power on again only once all installation and wiring is completed We recommend lightly tinning the wires before connecting them to the screw terminals Use only genuine accessories supplied by LCJ Capteurs Do not attempt any modification to the unit Never paint any part of the unit or alter its surface in any way Warranty is void in case of non following the instructions of use repair or maintenance without written authorisation 1 2 MAINTENANCE AND REPAIR The CV7 sensors do not require any maintenance Check the connections on a regular basis and make sure the junction boxes are dry and protected If the Wind pages of your instruments do not display the wind data correctly refer to the manufacturer s manual and check the connections before asking for service to your LCJ Capteurs dealer 1 3 DISPOSAL Equipments marked with the recy
7. ee ree rs 13 SRB OPTION oi AA AA AA AA nee one 14 12 1 CONNEC HON AA AA ANNA AA APA 14 12 2 SPE ORIOA NONG oan AA AA AA E 14 MOUNT ADAPTERS taser cect AA T 14 13 1 OR AA AA re eee ne eer eer ee eee ee ee 14 13 2 MOUNT ON VERTICAL SUPE TT 14 OP ECIFRICA PRE ENS ER cee sec AA 15 ADDENDUM iste sate seca AA AA AA se ea eet ses hee est a a dade ee AA AA 16 15 1 NIR INTERFACE sernir rke te eects sence sa oa eee AA AA AA r 16 15 2 USING THE CONFIGURATION APPLICATION eee eee eee 17 15 3 A INT G TEME LATE EE 18 PN AA APA PA AA AAP AA PMA 20 16 1 Se OF DELIN ERI a AALANGAN E se ADA AANO AA AA 20 16 2 NS TALCA FION AA AA AA AA AA 20 16 3 SEN ABONNEMENT API AA ees ones ee AA 20 16 4 CONNE TION aaa aaa aa a Aa aa 20 16 5 DIMENSION AA AA AA AA AA TE 20 OV GA D USB AA AA 21 17 1 CONFENFOPDELNERTS SE ee ee ee ene ee er ere 21 17 2 INSTALLA TON ne AA 21 17 3 SEN OR AHGNEMENT ee aa ka 21 17 4 BG IOa e AA AA AA AA AA 21 17 5 PINENSIONG AA ANA AA AA AA AA 21 Copyright 2014 LCJ CAPTEURS 3 ULTRASONIC WIND SENSOR LCJ CAPTEURS 1 GENERAL INFORMATION AND SAFETY GUIDELINE 1 1 GENERAL RECOMMENDATIONS The LCJ Capteurs sensors are Ultrasonic wind vanes anemometers with accurate factory calibration Install the sensor in in a location free from wind perturbation usually on the mast head Prepare the mast head for the mechanical installation Align the North mark of the bracket in order to have the CV7 C sensor heading to the bow The sensor s fine
8. 80x30 mm 150gr 11 ULTRASONIC WIND SENSOR LCJ CAPTEURS 8 OPTION ST 8 1 TYPICAL INSTALLATION OVERVIEW How to connect a CV7 ST toa ST60 Wind Wires from the CV7 cable red blue green OVDC Power Supply 8 2 CONNECTIONS This option allows the connection of a CV7 directly to the ROTAVECTAO input on your Raymarine instrument ST30 Wind ST50 Wind or ST60 Wind Power the junction box and the CV7 sensor as indicated below The green wire coming from the CV7 must be connected to the terminal marked CV3F The wires coming from the ROTAVECTAO are connected to the B and R terminal with matching colours The yellow wire coming from the CV7 is dedicated to a serial connection to a PC for use of the setup application see 15 2 Tight this wire with precaution for future use Make sure it is correctly isolated POWER 12V Red 12VDC LS Green CV3F NMEA B R gt Rotavecta BLUE ST 00000000 gt Rotavecta RED 8 3 COMMISSIONING Once all connections are completed refer to the Raymarine manual for the sensor s alignment 8 4 DIMENSIONS Dimensions 131 x 58 x 37 mm 12 9 OPTION BG 9 1 TYPICAL INSTALLATION OVERVIEW Wires from the CV7 Mast base Junction Box not supplied by LCJ Capteurs Power Supply and interface LCJ Capteurs B amp G Option B amp G Processor B amp G colourcode ndu NHIN 9 2 CONNECTIONS This o
9. 9 5 3 DIVINE ON seers Naam ccretuclees ti Ja dalwa Da kaaa alak alaala alaman 9 6 CANBUS CP TION AA 10 6 1 TYPICAL INSTALLATION OVEVIEW cccccccccceccesseccercescescceeceecercarcarsersecsaccaecarsarsarserserserserecarsarearseneerenssertens 10 6 2 CONNECTIONS a ve 10 6 3 COMMISSIONING cccecccccceccerceccerceccescececeecaccersercercerceecsaccaecarcaesarsersesseusrecarsarcarsarsarseserserecatcatserteneureeneereeates 10 6 4 SENSOR ALIGNEMENT 10 6 5 CALIBRATION OF THE BAROMETER eeerererererreeennenneenneneenrenranreneneneeneeneennenenn en ananena ranan 10 7 OPTIONGANBUS RE A a anaana narenn 11 7 1 TYPICAL INSTALLATION OVERVIEW 11 7 2 CONNECTION E E 11 7 3 ee NISSAN 11 7 4 CALIBRATION OF THE MAST ANGLE SENSOR MID SHIP AND MAST ANGLE ENDS 11 7 5 DIMENSIONS OF THE CANBUS JUNCTION BOX 11 8 OPTIONS la AA AN AA eee Aa 12 8 1 TYPICAL INSTALLATION OVERVIEW kaan ka karanka kan En Anar AEEA AEEA A AEEA nannaa annann 12 8 2 ONIN TIC IN A 12 8 3 COMMISSION e Eria EEEE a e EErEE E Ee ari R EEE eidi PEARSE Ciao 12 8 4 DIVINE 12 9 OPTIONS aNd s 12 9 1 TYPICAL INSTALLATION OVERVIEW 12 9 2 CONNECTIONS naina Ahaha GD GL aaa 12 9 3 SOS NN ence tess tec E aei 12 9 4 DIVENSIONS 12 10 OPTION SIL NEXUS NX2 SILVA and ElS0 see 13 10 1 sI de 13 2 Copyright 2014 LCJ CAPTEURS 11 12 13 14 15 16 17 ULTRASONIC WIND SENSOR LCJ CAPTEURS OOP TOWN BARO EEE 13 13 11 1 DIEN ION Han aa AA a Ue AA AA AA ee
10. 9392 60928 126464 126996 130306 130311 130314 PGNs processed by the option 59392 59904 60928 Power consumption 2 LAN 6 3 COMMISSIONING Refer to the connected instruments manual for pages setup and all functions related to wind and atmospheric pressure functions Once all wiring and connections are completed turn the power on and check the alignment It may be adjusted from your instruments setup menu Alternatively this can be done directly from the CanBus 10 6 4 SENSOR ALIGNEMENT Fine alignment of the mast sensor can be achieved at sea Sail on starboard and port to note the correction that needs to be applied from a tack to another Place the rotary button S1 in position 1 and use the and keys to change the value read on the display Adjust the value accordingly to the difference measured from a tack to another during sea trials The wind angle will correctly read on the display 6 5 CALIBRATION OF THE BAROMETER The atmospheric pressure sensor is calibrated against the nearest reference located on the shore level such as aa weather station The rotary button S1 placed on position2 allows calibrating the atmospheric pressure Once the button is in position 2 the value on the display can be adjusted using the and keys to match the reference Make sure your display is set to mb unit Copyright 2014 LCJ CAPTEURS 7 OPTION CANBUS RM 7 1 TYPICAL INSTALLATION OVERVIEW CV7 C
11. EA0183 data output is connected as shown below 12V NMEA out OPEN TO CONNECT NMEA out 16 5 DIMENSIONS mm 371 mm Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 17 CV7SF USB 17 1 CONTENT OF DELIVERY CV7SF sensor With vertical arm 17 2 INSTALLATION The CV SF wind sensor IS designed tor Operation outdoor exposed to natural light It must be installed in an area free from any air flow perturbation Choose a location free from any obstacle and situated at least 150 cm from the ground The radio signal maximum range is 200 meters Best results are obtained in a 50 meters distance between the sensor and its receiver The signal can be perturbated by materials such as carbon aluminium steel A minimum distance of 10 meters between the arm and any conductive material is recommended Specific environments may cause bad reception Please contact our technical support in that case 17 3 SENSOR ALIGNEMENT A mark below the sensor indicates the alignment The vertical bracket is designed for mounting on a horizontal surface usually the mast head on a sailing boat For mounting on the side of the mast an additional bracket is available separately see section 12 2 The CV7 sensor must be installed with the Nord mark on the bracket aligned to the geographical North for a fix installation on shoreUse a compass taking the deviation in account NORD NORTH
12. ULTRASONIC WIND SENSOR LCJ CAPTEURS USERS MANUAL CV7 CV7 Standard CV7 V CV7 C CV7SF LCJ CAPTEURS 25 All e des Cinq Continents ZA le Ch neFerr 44120 VERTOU France T l 33 0 2 40 05 08 55 Email info lcjcapteurs com www Icjcapteurs com EN 55022 EN55024 SIRET 42493307500022 RCS Nantes VAT FR17424933075 Copyright 2014 LCJ CAPTEURS CV7 manual 2014 English ULTRASONIC WIND SENSOR LCJ CAPTEURS CONTENT 1 GENERAL INFORMATION AND SAFETY GUIDELINE sccsccecceeseessesseeseeceeseeseeceessesseceeeeaneaneseeeneseesecseseasseneeeeenesees 4 1 1 GENERAL RECOMMENDATIONS ieeerrnreneereeeeeeeneenrenranrannenneneeneeneenr enr enneneneeneeneenrenren ennemies 4 1 2 MAINTENANCE AND REPAIR LU LALALALA LANE LUNA LA An nnununumunan 4 1 3 DISPOSAL 4 1 4 USE OF THIS MANUAL 5 1 5 VALIDITY OF THIS MANUAL 5 1 6 LIMITED WARRANTY 5 1 7 BBS NS NA 5 2 INSTALLATION OF A CV7 WIND SENSOR sese 6 2 1 TYPICAL INSTALLATION OVERVIEW 6 2 2 SENSOR ALIGNEMENT 6 2 3 CONNECTION Handaan aba haaha anG aa lad ar EER eaea oe e A oia ecis 6 2 4 SET UP COMMISSIONING C AALALA LALA LA LENA LALALALA LULU LULAN nA nnununununan 6 3 CS OR AA a a 7 3 1 CONTENT OP DELIVERY ea a ee AA ee 7 3 2 SENSOR ALIGNEMENT 7 3 3 DIMENSIONS nr nn 7 4 er OTT 8 4 1 CONTENT OF DELIVERY 8 4 2 SENSOR ALIGNEMENT 8 4 3 BIENS ON SR 8 5 ar eC ee ee ee eee 9 5 1 CONTENT OF DELIVERY 9 5 2 SENSOR ALIGNEMENT
13. apteurs com Make the following serial connection SubD 9 points a ao Pim Extract the file in a folder of your choice and copy the shortcut on the desktop O O O QO O Double click on the shortcut and select a COM port to use O O O O Power the CV7 Set your configuration from choices offered by the application Click on the Programmation CV7 button to save the settings and follow instructions CY7 girouette an mome tre ultrasons logiciel de configuration ES O x Configuration Edit Unit temp rature fe C CR Type d indicateur force du vent NHEAD183 C NEXUS SILVA noeuds C m s C km h C FI50 Ea N SO fili SE 5 NS 000 2 Ajustement d angle Direction 180 0 n Temp rature 070 0 Programmation C47 1 17 4 07 08 14 34 04_180 0 _000 2_H 020 0 C DA 07708 14 34 05 180 0 000 2 N A 020 0 C 04407408 14 34 06 180 0 000 2 N_A 02007 04707 709 14 34 07 180 0 000 2 N A 0700C 04 07 708 14 34 08_180 0 _000 2 N A 0700C B EHe al a mm GU Copyright 2014 LCJ CAPTEURS 17 ULTRASONIC WIND SENSOR LCJ CAPTEURS 15 3 MOUNTING TEMPLATE WARNING Check the scale when printing this document Measure indications are in millimetres Vertical bracket 18 Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS Oblique bracket Copyright 2014 LCJ CAPTEURS 19 ULTRASONIC WIND SENSOR LCJ CAPTEURS 16
14. cling symbol should be processed via a recognized recycling agency By agreement they may be returned to the manufacturerDo not mix electronic disposal with domestic or industrial refuse 4 Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 1 4 USE OF THIS MANUAL This manual serves as a guideline for the safe and effective installation operation and maintenance of the Ultrasonic Wind Sensors of the CV7 range from LCJ Capteurs It is recommended to follow carefully the instructions contained herein Keep this manual in a safe place 1 5 VALIDITY OF THIS MANUAL All of the specifications provisions and instructions contained in this manual apply solely to the following products Part Description CV7 CV7 standard Ultrasonic Wind Sensor CV7 V CV7 Ultrasonic Wind Sensor Vertical CV7 C CV7 high speed Ultrasonic Wind Sensor long carbon vertical arm CV7SF CV7 Wireless Ultrasonic Wind Sensor NMEA0183 receiver CV7SF USB CV7 Wireless Ultrasonic Wind Sensor receiver for USB Canbus CanBusinterface NMEA2000 Canbus RM CanBus interface for rotating mast NMEA2000 Option ST Interface for Raymarine ST Option BG Interface for B amp G Option baro Junction box with baro sensor Option USB Junction box with USB connector Support Bracket for installation on a vertical Vertical surface Adapt 1 1 standard adapter VHF or GPS type 1 6 LIMITED WARRANTY The LCJ Capteursagainst manufacturing defe
15. compatible with standard brackets available on the market such as the GLOMEX on feature on the picture below Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 14 SPECIFICATIONS Output data signal NMEA NMEA NMEA NMEA or NEXUS or NEXUS or NEXUS Output update 2 per second 2 per second 4 per second 1 per sec In day light every 3 seconds Sunrise amp sunset Wind module sensitivity 0 25 Kt 0 25 Kt 0 25 Kt 0 25 Kt Wind module resolution 0 1 Kt 0 1 Kt 0 1 Kt 0 1 Kt Wind module nini 0 25 to 80 Kt 0 25 to 80 Kt 0 25 to 80 Kt 0 25 to 80 pea Ha Power kania 8 to 33 VDC 8 to 33 VDC 8 to 33 VDC photovoltaic cells for transmitter 6 5 to 27 VDC for receiver Electrical consumption 9 5 mA 9 5 mA 9 5 mA autonomous for transmitter 5 8 mA for receiver Operating temperature range 15 C 55 C 15 C 55 C 15 C 55 C 10 C 55 C without iceing Connection line 25 m of cable 25 m of cable 25 m of cable Radio transmitter 4 x 0 22 mm 4 x 0 22 mm 4 x 0 22 mm 433 mHz Tx power 10 dom Message time 25 ms Interconnection Direct 12 V Direct 12 VO V Direct 12 VO V Receiver 0 V NMEA NMEA Superheterodyne NMEA NMEAC NMEAC ASK 433 MHz NMEAC Sensitivity 110 dom Outputs via screw terminal Weight of the head 100 g 100 g 100 g 100 g Oblique 30 cm arm Vertical 30 cm Vertical 75 cm Vertical 30 cm arm Alu 12 mm arm carbon arm Q 16 Alu 16 mm Alu 16 mm Mount
16. cts for a period of two years from the date of purchase It is limited to the repair and or replacement of the product It does not cover installation costs and shipping costs of faulty units A proof of purchase may be asked when filling the warranty request which must be received by writing Once the warranty request is accepted by LCJ Capteurs the unit must be sent to LCJ Capteurs address in France LCJ Capteurs guarantees that each of their ultrasonic wind sensors are tested and calibrated before despatch Operations not in compliance with the instructions described in the present manual may result to damage the unit or alter its performances In such cases the warranty IS void 1 7 RESPONSABILITY LCJ Capteurs do not accept responsibility for e Consequential damage to the use of a CV7 sensor e Possible errors in the manuals and their results Copyright 2014 LCJ CAPTEURS 5 ULTRASONIC WIND SENSOR LCJ CAPTEURS 2 INSTALLATION OF A CV7 WIND SENSOR 2 1 TYPICALINSTALLATIONOVERVIEW This diagram features a CV7 Standard The typical installation is the same for CV7 V and CV7 C pe 2 3 CONNECTIONS Connect to 12 V power supply 10 a 14 VDC Connect the yellow and green wires to the NMEA input of the instrument 2 4 SET UP COMMISSIONING You can use your sensor immediately Set up such as speed unit temperature unit and data filtering can be set L up with the application configuration CV7 downloadable
17. ing base Total weight including arm and 200 g 200 g 200 g 200 0 bracket Copyright 2014 LCJ CAPTEURS 15 ULTRASONIC WIND SENSOR LCJ CAPTEURS 15 ADDENDUM 15 1 NMEA0183INTERFACES NMEA0183 Output on a 4mA current loop 4800 Bauds no parity 1 stop Bit Constant flow at 500 milliseconds except CV7 C at 266 milliseconds Variable fields lengths comma separator Sentence prefix End of sentence CR LF Examplesof typical sentences output by CV7 CV7 V CV7 C IMWV 225 0 R 000 0 N A 38 WIXDR C 022 0 C 52 SPLCJ 5801 5F01 AA 4253 3341 PLCJEA870 6D98 C500 0056 AC Wind sentence SIIMWV 226 0 R 000 0 N A 0B CheckSu L CV7 statu A correct mea V incorrect measure Wind spead unit N Wind spead Reference Wind direct grees Wind temperature sentence WIXDR C 022 0 C 52 CheckSum Unit Val ith one decimal Typical sentence for CV7 BARO CV7 V BARO and CV7 C BARO SWIMDA 1 1 033 B 019 5 C Unit Celsius Temperature value wi e decimal Atmospheric pr in Bar Sentence for LCJ CAPTEURS technical use only SPLCJ AAAA BBBB CC DDDD EEEE SPLCJEFFFF GGGG HHHH II JJ Logging two minutes of NMEA sentences flow allows to makea proper diagnostic 16 Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 15 2 USING THE CONFIGURATION APPLICATION Configuration of the CV7 sensor The Configuration CV7 C software can be downloaded from www lcic
18. on 6 identification of the potentiometer s polarity port starboard values Position 5 mid ship Place mast in mid ship position and set the angle to 0 Position 4 port end Place the mast in port end position and set the angle to the relevant value theoretical or measured Position 3 starboard end Place the mast in starboard end position and set the angle to the relevant value theoretical or measured 7 5 WIND SENSOR ALIGNEMENT Fine alignment of the mast sensor can be achieved at sea Sail on starboard and port to note the correction that needs to be applied from a tack to another Place the rotary button S1 in position 1 and use the and keys to change the value read on the display Adjust the value accordingly to the difference measured from a tack to another during sea trials The wind angle will correctly read on the display 7 6 CALIBRATION OF THE BAROMETER The atmospheric pressure sensor is calibrated against the nearest reference located on the shore level such as aa weather station The rotary button S1 placed on position 2 allows calibrating the atmospheric pressure Once the button is in position 2 the value on the display can be adjusted using the and keys to match the reference Make sure your display is set to mb unit These values are automatically stored in the devices memory They can be fine adjusted after sea trials 7 7 DIMENSIONS OF THE CANBUS JUNCTION BOX 130x
19. ption allows the connection of a CV7 directly to the MHU input on your B amp G Power the junction box and the CV7 sensor as indicated below The yellow wire coming from the CV7 is dedicated to a serial connection to a PC for use of the setup application see 15 2 Tight this wire with precaution for future use Make sure it is correctly isolated Network Other Do not use magaan CV7 yellow not connected P go O O Purple 12V battery O O Black OV battery O O Orange O Green O Blue O Red O Green NMEA out O Ol ned NMEA out O NG Blue Once all connections are completed refer to the B amp G manual for the sensor s alignment 9 3 COMMISSIONING 9 4 DIMENSIONS Dimensions 131 x 58 x 37 mm Copyright 2014 LCJ CAPTEURS 10 OPTION SIL NEXUS NX2 SILVA and FI30 NX2 or F130 interconnections to WIND DATA Instrument Back Fi30 NX2 12VDC with Power supply 10to 14 VDC ov NEXUS WIND LOG 1 2 3 4 S R ov Blue Red Wires CV7 LNC Yellow 2 Interconnections NX2 or FI30 SERVER SHIELD 13 WHITE 14 YELLOW 15 GREEN 16 m m ee Red 12vpc Blue ov CV7 Green 1 Yellow 2 sdl 10 1 DIMENSIONS Dimensions 131 x 58 x 37 mm Copyright 2014 LCJ CAPTEURS ULTRASONIC WIND SENSOR LCJ CAPTEURS 11 OPTION BARO 11 1 CV7 BARO Option Wires from the CV7 red blue green yellow Not connected Power S
20. upply Yellow Green To your instrument s NMEA 0183 input Screw terminal 12V0V BR POWER CV3F NMEA ST 11 3 DIMENSIONS Dimensions 131 x 58 x 37 mm 13 ULTRASONIC WIND SENSOR LCJ CAPTEURS 12 USB OPTION bag CONNECTIONS The junction box features a screw terminal and a standard USB cable Open the box to complete the connections The USB junction box is powered by the USB connection to the PC Connect the wire coming from the CV7 as indicated on the diagram above Plug the USB cable to the PC The driver will automatically be installed by the Windows system Windows 7 and above Alternatively the latest version of the driver can be downloaded from the technical support section of the website www lcicapteurs com It is an executable file Double click on the file to launch the installation Once the CV7 is connected to the USB port your relevant software Will immediately identify the NMEA0183 sentences via an emulated COM port Wires from the CV7 Red Blue Green USB output to PC 12 3 SPECIFICATIONS Dimensions 57 x 43 x 24 mm Weight 20 g without cable and connector Cable length 1 50 m Standard USB type A connector Screw terminal 14 13 MOUNT ADAPTERS 13 1 1 ADAPTOR v Pgs ae This optional accessory allows mounting a CV7 sensor on any standard antenna mounting bracket External diameter 40 mm Height 50 mm 13 2 MOUNT ON VERTICAL SURFACE CV7 V base is
Download Pdf Manuals
Related Search