USER MANUAL
Contents
1. 15 12 1 A fixed set 15 12 2 Rotating disc 15 13 Electronic drawing me cac su RA e YER 16 Add Standard 17 1 guidelines Congratulations choosing our products Please carefully read this instruction manual in its entirety and keep it well for using reference This manual contained about the installation and the relative using inform ation of this products Please according to this manual s relative speaking when using this equipment This equipment was made of new style high intensity plastic It fully shows the modem times light charac teristic with beauty struture And it was made according to CE standard Fully up the internation standard of DMX512 agreement Master or slave in phase ntrol Can be use in large entertainment theater performing and palying hall erc When receive the product please be careful to take and put check if the product has damage or not because of transportation and check the following parts 1 Signal cable 1PC 2 Safty cable 1PC 3 User Manval 1PC 4 Omega holder 2PCS 5 Power cable 1PC 5 Service card 1PC 1 1Package Unpacking the fixture 1 Open the flight case couer 2 With one person on each side lift the fixture out of the flight case 3 Un2. Set Dmx 001 Address Value Display PAN Moving 8 Auto Program Alone 5 Master 3 OFF 5 Music Control Alone Master OFF Time Information Current Time ON OFF Total Run Time ON OFF Clear Fixture Time ON OFF If set channel 1 2 3value to 10 3 10 2 choose ON then E clear Total Run Time 8 Head Temp ON OFF Information Product Info Logo Unit Model VerXX Company WEB Status Settings Addr Via DMX ON OFF Controller revise address switch When it is ON set channel 1 to 10 channel 2 to 10 when address 2255 then to 11 address channel is 3 plus 255 channel 3 set to the revise address value then after 20s address change to channel 3 No DMX Status Close p Hold Auto Music Pan Reverse ON OFF Tilt Reverse ON OFF Fine Resolution ON OFF Feedback ON OFF WDMX Alone Master OFF RESET Mic Sensitivity 70 0 99 Display Set Dis Close Time 05 02 59M Temperature C F Celsius Fahrenheit Reset Default ON OFF 10 c Reset 2 Reset Pan Tilt 2 9 Reset Color Ys Reset L Reset Else Test Channel PAN XXX PAN XXX en TILT XXX o 3 Regulate Value Password Password XXX Password 088 lt 8 DMX protocol Mode2 Name Function DMX Value 1 Pan 8BIT PAN 8BIT 0 255 Pan 16BIT Pan 16BIT 0 255 Tilt 8BIT TILT 8BIT 0 0 225 Speed pan tilt 226 235 movement blackout by all wheel chang
3. USER MANUAL Iso 52X30MM 3 Moving head Professional stage lighting equipment Table of content 1 Open Package 1111 1 1 1Package nores a heran 1 2 Safety instructions cei iicuckiii diia arena 1 3 Operating determination esses nennen nnne nnn 3 4 Rigging the fixt re iore ee india 4 4 1 Mounting eniti ae IPs eR UR isse 4 4 2Installing the Clamps u2222020220202n0n0nnnnnnn ann nn nennen nnns 5 4 3 POWER Connection inrer ite cna isis 6 5 Description of the 7 GC DIMENSION M 8 7 Display control ee a dd 9 7 1 Navigation in the 2222 9 7 2 Display OPeration 4 2 nalen pen 9 7 III ENT 10 8 DMX protocol cocos en 11 9 Maintenance and cleaning eese enne 13 10 Electric equipment 14 10 1 Electrical nennen 14 10 2 Channel 14 10 3 Menu 0 01 2 14 11 light table miii aa ee nenne 15
4. N m JD 2NSENSE D GMSENS D Signal Te LED Eh e E 8 a ar HC028N U03V1001 LED 16 Add standard Version Set Dmx A001 AXXX Address Value Display PAN Moving 8 Auto Program Alone 5 Master 3 OFF 5 Music Control Alone Master OFF Time Information Current Time ON OFF Total Run Time ON OFF Clear Fixture Time ON OFF If set channel 1 2 3value to 10 3 10 2 choose ON then E clear Total Run Time 8 Head Temp ON OFF Information Product Info Logo Unit Model VerXX Company WEB Status Settings Addr Via DMX ON OFF Controller revise address switch When it is ON set channel 1 to 10 channel 2 to 10 when address 2255 then to 11 address channel is 3 plus 255 channel 3 set to the revise address value then after 20s address change to channel 3 No DMX Status Close 2 Hold Auto Music Pan Reverse ON OFF Tilt Reverse ON OFF Fine Resolution ON OFF Feedback ON OFF Mic Sensitivity 70 0 99 Display Set Dis Close Time 05 M 02 59M Temperature C F Celsius Fahrenheit Reset Default ON OFF 17 Reset All c 2 Reset Pan Tilt Reset Color Reset Gobo L Reset Else Test Channel 5 o 3 Regulate Value Password Pass
5. N Yellow Green Green Earth DMX 512 Connection DMX 512 connection connection between fixtures Only use stereo shieded cable and 3 pin XLR plugs and connectors in order to connect gt ur ur DMX512 Caution At the last fixture the DMX cable has to be terminated with a terminatou solder a 120 resistor between signal and Signal into a 3 pin XLR plug and plugitin the DMX output of the last fixture DMX output DMX iutput DMX output DMX iutput 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal 4 N A 5 N A DMX Terminator Diagram For installations where the DMX cablehastoruna long distance or is in an electrically noisy environment 2 1 itisrecommended to use aDMX terminator This help in preventing corruption of the signal by electrical noise The DMX terminator is simply an XLR plug with 3 a120Q resistor connected between pins 2 and pins 3 which is then plugged into a the output XLR socket of 1200 the last if xture in the chain N2 ps 5 Description of the device 1 HEAD 2 ARM 3 BASE 4 3 pin XLR female 5 5 pin XLR female 6 power switch 7 power in 8 Insurance seat 9 3 pin XLR male 10 5 pin XLR male 11 MIC pilot hole 1813 14 15 12 WDMX wire 13 LCD display g a Ep 14 MO
6. consider that unauthorized modifications on the device are forbidden due to safety reasons gt If this device will be operated any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock burns due to ultraviolet radiation lamp explosion crash etc The lamp used in this projector is a discharge lamp After switching off don t attempt to restart the projector until la mp has cooled this will require approx 15 minutes Switc hing the lamp on and off at short intervals will reduce the life of both the lamp and the projector But occasional bre aks will prolong the lamp and projector 4 Rigging the fixture 4 1 Mounting FIXTURE can by installed in any position Pay attention to the regulations of The installation shall be done by qualified staff only Forthe various mounting positions of the FIXTURE standing on the floor sideways or hanging different accessories kits are available Through this a safe and firm installation is assured You ll find special connectors on the bottom side of the system which are put to use here In addition the front side of the system is marked with FRONT as this is important for a even orientation during installation 4 2 Installing the Clamps DANG ER TOLIFE Please consider the respective nati
7. slow 4 63 No rotation 64 67 Backwards rotation from slow to fast 68 127 135 143 3 144 151 160 167 14 3 facet rotating 168 175 prism Macro 7 176 183 192 138 Macro 10 200 207 12 216 223 13 224 231 14 232 239 Macro 15 240 247 Macro 16 248 255 Max diameter to Min diameter 0 191 lris Pulse opening fast to slow 192 223 Pulse closing slow to fast 224 255 Zoom Continuous adjustment from near to far 0 255 adjustment from near to far 0 255 No function shutter open 0 Strobe effect slow to fast 1 95 No function shutter open 96 127 Strobe Pulse effect in sequences 128 159 No function shutter open 160 191 Random strobe effect slow to fast 192 223 Dimmer Intensity 0 to 100 0 255 Normal 0 20 No function 20 79 All motor reset 80 84 m motor reset 85 87 Reset 88 50 91 93 34 56 motor reset 97 99 9 Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not buildup on or within the fixture Otherwise the fixtures light output will be significantly reduced Regular cleaning will not only ensure the maxim um light output but will also allow the fixture to function reliably through out its life A soft lint free cloth moistened with any good glass cleaning fluid is recommended under no circum stances should alcohol or solvents be used DANG ER Disconnect from the mai
8. DE button e m a 15 UP button 11 16 DOWN button 17 ENTER button 18 WDMX pilot lamp 12 17 16 6 Dimension 463 mm o 1 79 mm 537 mm 85 mm 11 mm 7 Display control 7 1 Navigation in the Menu Using touch control switch and LCD display and this can be simply and easily setthe address code and functions code If you view or modify the lighting feature set then press MODE button the LCD display will enter the menu interface Both there is sub menu corresponding to the functional operation ofthe main menu Each of the menus is representative of the specific features of the lamp The specific contents shows as the table menu below Set or browse lighting function press UP or DOWN button Press ENTER to save your changes or enter the submenu Press the UP or DOWN can change the numerical increase or decrease in value Press the MODE button to return to menu Such as 60 seconds without pressing any key it will automatically exit the menu operation interface 7 2 Display Operation Connect power and open lamp power switch Lamps began to reset self tes
9. em fails the fitting falls as little as possible If the safety chain gets used it needs to be replaced with a genuine spare Minimum distance of illuminated objects The projector needs to be positioned so that the objects hit by the beam of light are atleast 2 5 metres from the lens of the projector Minimum distance from flammable materials The projector must be positioned so that any flammable materials are at least 0 20 metres 8 from every point on the surface of the fitting Mounting surfaces WV It is permissible to mount the fitting on normally flammable surfaces Maximum ambient temperature For the fitting to operate well and reliably the ambient temperature should not 440 C exceed 40 C 104 F gt Protection against electrical shock Connection must be made to a power supply system fitted with efficient EM earthing Class appliance according to standard EN 60598 1 It is moreover recommended to protect the supply lines of the projectors from indirect contact and or shorting to earth by using appropriately sized residual current devices gt Hooking up to the supply mains Connection to the electricity mains must be carried out by a qualified electrical installer Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label This label also gives the input power to which you need to refer to evaluate the maximum number o
10. f fittings to connect to the electricity line in order to avoid overloading gt Temperature of the external surface te 80 C The maximum temperature that can be reached on the external surface ofthe fitting ina thermally steady state is 80 C 176 F Maintenance Before starting any maintenance work or cleaning the projector cut off power A from the mains supply After switching off do not remove any parts of the fitting for at least 10 minutes After this time the likelihood of the lamp exploding is virtually nill Ifitis necess ary to replace the lamp wait for another 15 minutes to avoid getting burnt The fitting is designed to hold in any splinters produced by a lamp exploding 4 The lenses must be mounted if visibly damaged they have to be replaced with genuine spares gt Lamp The fitting mounts a high pressure lamp that needs an external igniter This A igniter is fitted onto the apparatus Carefully read the operating instructions provided by the lamp manufacturer Immediately replace the lamp if damaged or deformed by heat 3 Operating determinations gt This device is a moving head for creating decorative effects and was designed for indoor use only gt If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperat
11. he rear panel gt Always plug in the power plug least Make sure that the power switch is set to off position before you co nnections with the mains with particular caution Make sure that the power cord is never crimped or damaged by sharp edges Check the decice and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the powercord gt This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth gt The electric connection repairs and servicing must be carried out by a qualified employee Do not connect this device to a dimmer pack Do not switch the fixture on and off in short intervals as this would reduce the lamp s life rly mean that the device is defective Do not touch the device s housing bare hands during its operation housing becomes hot gt For replacement use lamps and fuses of same type and rating only CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics gt Installation Make sure all parts for fixing the projector are in a good state of repair Make sure the point of anchorage is stable before positioning the projector The safety chain must be properly hooked onto the fitting and secured to the framework so that if the primary support syst
12. ing 236 245 no 40 Open white 0 9 olo 9 Color 2 Color1 20 29 Color 2 30 39 Color 3 Color 2 40 49 Color 3 50 59 Color 4 Color 3 60 69 4 Color wheel1 70 79 80 89 90 99 Color 6 Color 5 100 119 Color 6 110 127 ainbow effe om Q 9 18 No rotation 188 193 Backwards rainbow effect from slow to fast 194 255 en white 0 9 Color 1 10 19 Color 2 Color1 20 29 Color 2 30 39 Color 3 Color 2 40 49 Color 3 50 59 Color 4 Color 3 60 69 7 5 Colorwhee2 Color 4 70 79 Color 5 Color 4 80 89 Color 5 90 99 Color 6 Color 5 100 119 Color 6 110 127 Forwards rainbow effect from fast to slow 128 187 No rotation 188 193 Backwards rainbow effect from slow to fast 194 255 0 9 10 19 20 29 30 39 40 49 50 59 60 69 8 Rotating gobo change 70 89 90 109 110 129 130 149 150 169 170 189 rotation slow to fast 190 255 Gobo indexing 0 127 Forwards gobo rotation from fast to slow 128 187 3 E INL No rotation 188 193 Backwards gobo rotation from slow to fast 194 255 0 14 15 29 30 44 45 59 60 74 75 89 6 90 104 Gobo 7 105 119 130 138 140 745 150 159 Gobo 5 shake slow to fast 160 169 Gobo 6 shake slow to fast 170 179 Gobo 7 shake slow to fast 180 189 Rot gobo wheel cont rotation slow to fast 190 255 closed 0 3 Forwards rotation from fast to
13. l being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector has to be installed out of the reach of people If the projector shall be lowered from the ceiling or high joists professional trussing system s have to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the projector The projector can be placed directly on the stage floor or rigged in any orientation on atruss without altering its operation characteristics For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carabines Pull the safety rope through the two apertures on the bottom of the base and over the trussing system etc 4 3 POWER Connection If you wish to change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected Cable EU Cable US Pin International Brown Black Live L Light blue White Neutral
14. lock pan and tilt before operating fixture Packing the fixture 1 Disconnect the fixture from power and allow it to cool 2 lock head and arms as figure 3 Place the fix ture in the bottom of the flight case and cover the case without forcing lamp holder lock Arm lock 3 Level vertical transportation lock Aviation box 2 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manualentertainment theater performing and palying hall etc N CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and toen sure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important gt The manufacturer will not accept liability for any resulting damages caused by the non observance ofthis manual or any unauthorized modification to the device gt Please consider that damages caused by manual modifications to the device are not subject to warranty gt Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution gt Make sure that the available voltage is not higher than stated on t
15. ns before starting any maintenance work The front objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos m ay be cleaned with a soft brush The interior of the fixture should be cleaned at least annually usinga vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recom m end lubrication in six month intervals The quanity of oil must not be excessive in order to avoid that oil runs out when the gobo w heel rotates There are no serviceable parts inside the device except for the lam p and the fuse Replacing the fuse If the lam p burns out the fine w ire fuse of the device might fuse too Only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead 10 Electric equipment specification 10 1 Electrical paramters SOURCE ATRIA SI320 White LED POWER 500W AC220V 50HZ VOLTAGE AC 100 240V 50 60HZ NET WEIGHT 26KG 10 2 Channel Characteristics 17 15 DMX CHs Scan 540 Tilt260 Scan speed adjustable Scan following with shutter Fixture could auto reset High power LED source color wheel 2 white 6 colors Variable speed two way rainbow effect color positioning Rotating gobo wheel 6 rotating gobos with white Static gob
16. o wheel 7 Static gobos with white Prism internally install prism effect Iris Linearity adjust pulse variation 9 Focus Linearity 10 Zoom Linearity 11 Strobe two motor strobe synchronous non synchronous random strobe effect 12 Dimmer linear dimmer 10 3 Menu Function 1 Blue White LCD display graphic 2 Each DMX Value displayable 3 Monitor could ON OFF automatically 4 Show fixture lamp use time 5 No signal fixture status keep reset status maintain status AutoPlay procedure sound control status 11 light table 35 Lux 2252 563 250 141 15 5 Lux 10470 2618 1163 654 8 5 E 8 Distance m 5 10 15 20 35 Gobo diameter m 3 15 06 3 09 45 012 6 15 5 Gobo diameter m 1 36 02 72 04 08 05 44 12 Gobo 12 1 A fixed set of design Aluminum Inside diameter 32 4mm Internal diameter26mm 12 2 Rotating disc of design glass design Inside diameter 37 4mm Internal diameter26mm 00 ays red blue green orange yellow black 13 Electronic drawing 2 cm 890314007 Ed bed F 4N U0IV QD Mr ERA My ERAN zem O x CUNG
17. onal norm s during the Installation The installation must only be carried out by an authorized dealer The installation of the projector has to be built and constructed in a way that can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g An appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall n if the main attachment fails W hen rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The projector should not be installed outside areas where persons m ay walk by or be seated Impor tank Overhead rigging requires extensive experingCE including but not limited to calculating working load limits installation materia
18. t at the same time LCD display shows company LOGO website product model software version Reset self test is finished the display will show the following table that is the lighting of the state Display window is set to display the status of the DMX address 001 said the DMX address code If the display no flashes that indicate the DMX signal is connected properly This status can be used to check the lighting and the console connection is normal or not Display window is set to display each channel DMX value state Bottom of the screen location to displays the channel name Central location to displays the channel s DMX value The lamps can be set to host voice run host running built in program Stand alone voice Stand alone running built in program when set to host it can not connect to the console or there will be interference Lamps in the reset process if there is a channel failure the LCD screen will rotate the PAN TILT COLOR1 COLOR2 RGOBO GOBOR RGOBO2 PRISM IRIS FOCUS information That is to say horizontal vertical Color1 Color2 Fix gobo wheel Rotaring gobo wheel Iris focus prism have fault When failure information appears the lamps will once again self test to reset a time and Verifies failures channels and then Lamps into the normal control state However the failure of the channel will not be controlled 7 3 lt
19. ure gt Never run the device without lamp gt Do not shake the device Avoid brute force when installing or operating the device Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles When choosing the installation spot please make sure that the device is not exposed to heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others gt The minimum distance between light output and the illuminated surface must be more than 1 5 meters Make sure that the area below the installation place is blocked when rigging derigging or servicing the fix ture gt Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only gt Operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastend gt The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns gt The maximum ambient temperature 40 C must never be exceeded gt Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please
20. word XXX Password 088 lt PAN XXX
Download Pdf Manuals
Related Search