Digidrive V2 - Void Acoustics
Contents
1. 1 Power up the sending device mixing desk then power up the Digidrive V2 make sure the power amplifiers are off before powering either of the other units up 2 On the Digidrive V2 press the Menu button until the routing page is displayed and scroll through with the control wheel until routing is Stereo 3 way then press Exit to return to the main page 3 Now use the CH Select buttons to scroll through to Out 1 Use Page to get to the Link page ensure link is On if channel display is Out 12 then link is on already Repeat this for Outputs 3 4 and 5 6 3 User Manual Digidrive V2 VH 4 For the crossovers for each linked output channel scroll through channel pages until LowPass is displayed Using the control wheel and control wheel button set the desired frequency and filter type and check the LPF is enabled 5 For the HPF scroll across one page to HighPass and repeat the process 6 Now the crossovers are set scroll through the remaining pages to set the values for the rest of the settings EQ Limiter Delay for each output channel There are multiple parameters to some settings use the control wheel button to change between them 7 To store the program press the Menu button until Save is displayed Use the control wheel button to select and choose the name of the preset Use Exit to backspace and press Menu again for saving no yes 8 When the preset program has been finalised and saved power up the2. 1S3 PUJ peoy sumed OL HUN SONSNODY PIOA sonsnooy PIOA 03 xoq jeui amp uo sy UI A qe19jeud jonpojd ayy unay siuBu AJOJNJEJS JNOA sjoaye em ou UI AJUEJJEM eu Jeqwnu uonesuoujne usna e 196 pue jonpoud ayy peseuound no woym wouy Jajeap ay joeJuoo lede spaau jonpoJd pio JNOA JI op 03 3eUM SJaJBap pesuoune S JO Sonsnooy PIOA Aq pied aq im Keuunof usnja ayy uo zyja pue eoueunsul Hued Aiesseoeu se oJd yom AJUEJJEM JI Jawojsna ay 0 Daun eq JJIM Sonsnooy PIOA 0 sjsoo abeuleo epoo ISO 4 Jequunu uomgestiJoujne uJnjeJ e BUILIEJQO 1s4y Wou sonsnooy PIOA 0 SPOOB pues jou oq JISUEJ ui S EWEP pajayns jou sey jonpoud au JEUL v JJEJS eouyos sonsnooy PIOA uey Jayjo uosJed Aue Aq uy pajadule JO pejquuessesip peyipow ueeq jou sey jonpoud ay jeu sseJppe pue weu sJeijddng lt c old snjejedde jjnej Jo ajqeyinsun UJIM uonounfuoo UI peyesedo Jo pesnqe useq jou seu jonpoud ay eyl Z Jequunu euas aseyound jo junoo ayy UI pije Ajuo SI queJuem siy PES e MEE suorpinser Duwoyoy ISPOW aseyoind jo ejeq ay o j2efqns eseuound jeuiBuo JO ajep ay Woy SJESA jo ponad e 10 diysueuwy om JO sjeuejeui jjnej 0 anp sjoajap 1sureBe paajueJen si jonpoud sonsnooy PIOA SIUL AJUBJJEM ITION sonsnooy PIOA Adog AJUBJIEM IION S J UMO epoo JSOd SseJppe pue eweu INOA epoo JSO4 sseJppe pue oweu siaiddng 0 Jaquinu jeueg Joa DO
3. interest insurance closing costs and other finance charges minus reasonable depreciation on the product If a refund is necessary the Owner must make the defective or malfunctioning product available to Void free and clear of all liens or other restrictions MODIFICATIONS OF EQUIPMENT Void reserves the right to modify or change equipment in whole or part at any time prior to delivery thereof in order to include therein electrical or mechanical improvements deemed appropriate by Void but without incurring any liability to modify or change any equipment previously delivered or to supply new equipment in accordance with any earlier specifications DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES YOU THE OWNER ARE NOT ENTITLED TO RECOVER FROM VOID ANY INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN THE VOID PRODUCT THIS INCLUDES ANY DAMAGE TO ANOTHER PRODUCT OR PRODUCTS RESULTING FROM SUCH A DEFECT WARRANTY ALTERATIONS No person has the authority to enlarge amend or modify this Warranty This Warranty is not extended by the length of time which the Owner is deprived of the use of product Repairs and replacement parts provided pursuant to the Warranty shall carry only the non expired portion of the Warranty THIS STATEMENT OF WARRANTY SUPERSEDES ALL OTHERS CONTAINED IN THIS MANUAL 33 User Manual ZSE 1591 0Z8 0 bb Xed ZEE 1991 0 8 0 vr RL YIN arr GLHA 19SJ0Q Orb SLHA JesJog ejoog SF PUJ peoy sumed gol Wun ejoog
4. 12 User Manual Digidrive V2 WOIA ELE Operating the Digidrive V2 iii AS err SRL ee eae ORSA Channel Select e Using the CH SELECT and CH SELECT buttons users can select the channel s to control This can be Input AB CD Output 12 34 56 or Input A B C D Output 1 2 3 4 5 6 l a Input Menus Each input channel has a set of Menus for specific parameters accessed with the PAGE and PAGE buttons e Gain 48 00dB mute to 12 00dB in 0 25dB steps In A Gain 00 00dB e Delav Oms to 2000ms in 0 01ms steps Bv depressing the control wheel units can be changed to feet or mm In A Delav 000 000ms e Low Pass 50Hz to 20kHz off in 1 10 50 and 100Hz steps By depressing control wheel users can enable disable it and change the Filter Tvpe In A LowPass Freq 80Hz 13 User Manual Digidrive V2 VH High Pass 20Hz off to 20kHz in 1 10 50 and 100Hz steps Depressing control wheel button users can enable disable it and change the Filter Type In A HighPass Tvpe BUT 24dB e PEQ 1 10 20Hz to 20kHz in 1 10 50 and 100Hz steps Gain from 12dB to 12dB in 0 25dB steps Q from 0 20 to 25 in 0 10 steps Change from Freq Gain Q by depressing the control wheel In A PEQ XX Q 1 00 D Limiter 50 00dBu to 12 00dBu in 0 25dBu steps Depressing control wheel button users can change the Release from 10 to 100 In A Limiter Thr 0 75dBu e Link select whether inputs A B
5. A If you want to dispose of this product do not mix with x general household waste There are separate dle collection systems for used electronic products in accordance with legislation under the WEEE Directive WA Directive 2002 96 EC and is effective only within the European Union This product is Rohs compliant Ey 32 User Manual Digidrive V2 VH lO E TEE LET A2 LIMITED WARRANTY THE WARRANTY For a period of three 3 years from the date of delivery to the original purchaser as shown on the original invoice or sales receipt Void Acoustics hereinafter Void warrants to the ORIGINAL OWNER of each new Digidrive V2 provided it was purchased at an Authorised Void Dealer that it is free of defects in materials and workmanship and that each product will meet or exceed all factory published specifications for each respective model Void agrees to repair or replace at its discretion all defective parts at no charge for labour or materials subject to following provisions WARRANTY VIOLATIONS Void shall take no responsibility for repair or replacement as specified under this warranty if the damaged product has been subject to misuse accident neglect or failure to comply with normal maintenance procedures or if the serial number has been defaced altered or removed Nor will Void accept responsibility for or resulting from improper alterations or unauthorised parts or repairs This warranty does not cover any damage to s
6. menu backspace 4 LCD shows information about the unit 5 Copy WILL BE AVAILABLE IN A FIRMWARE UPDATE 6 Paste WILL BE AVAILABLE IN A FIRMWARE UPDATE 7 Control Wheel gives velocity sensitive control over parameter values There is also a button click to allow changing parameters 8 Mute mutes un mutes the corresponding output channel When a channel is muted a red LED will light up 10 User Manual Digidrive V2 VH Lu E Rear Panel 1 Main Fuse T315 mA 250V 2 Power Input connects via a standard IEC socket 3 XLR Output Standard female XLR socket pin 1 ground shield pin 2 ve pin 3 ve 4 Network Socket 5 XLR Input Standard male XLR socket pin 1 ground shield pin 2 ve pin 3 ve 11 User Manual Digidrive V2 VH op Turning on the Digidrive V2 e When powering up the Digidrive V2 an initialization screen will be displayed on the LCD screen Initializing e The device will take a few seconds to boot up during the initialization process where all of the LEDs on the front panel will light up e Once the initialization process has finished the LCD screen will show the main screen Digidrive V2 DEFAULT PRESET NOTE when powering up the device after the first time and or presets have been made saved the main screen will display the name of the last used preset Digidrive V2 XXXXXXXXXXXXXXXXXX e The Digidrive v2 is now ready for operation
7. power amplifiers Now the system is ready to go NOTE alternatively setting up a preset can be made beforehand on the Live Link software and synced with the Digidrive V2 unit This allows the user to simply connect the unit to a laptop with Live Link plug in the appropriate connections turn each bit of equipment on in the correct order and the system is ready to go 4 User Manual Digidrive V2 VH Digidrive V2 User Manual 5 User Manual Digidrive V2 VH COM TOINS Atm 0 0 Quiek Start EE Ae ARNE 2 OT el EE 2 0 2 Step By Step ceret eterne NENNEN NENNEN ker KRA 3 1 0 Introduction to Digidrive VI 8 2 0 Features eee adi 9 305 Front Panel eri err Se ebe EES PR nex AS 10 4 0 Rear Panel esce eee airis 11 5 0 Turning on the Digidrive NI 12 6 0 Operating the Digidrive NV 13 6 1 Channel Select uk 13 6 2 Input Men s 5 ire ALAR EAA AANE KORNE VARAAT 13 6 3 Output Menus NENNEN 15 6 4 System Menus o ooccccccccncncncncncccnccnonenencnanonccacncnanancno 16 7 0 Live Link Control Interface AAA 17 7 1 Minimum System Requirements cse 19 7 2 Installing Live Lmk I 19 7 3 Connecting the Digidrive NV 19 7 4 Starting Live Link NENNEN NNN 20 6 User Manual Digidrive V2 WOIA 7 5 Using Live Link dr Loke hed ENER EES NEE ERKENNEN ENER 20 7 6 Digidrive V2 Control Window esee 20 CeO Ae MAIN M
8. store loaded from the device NOTE To store a preset from the computer onto the device it must first be loaded into Live Link and then the Store button pressed under Unit Presets It would be advisable for the user to check on the device that the preset has loaded before disconnecting i WE X Over e This tab shows the crossovers for each of the 6 outputs The right hand side of the window includes metering for each output 48dB to 12dB as well as Link buttons for stereo linking outputs 1 2 3 4 5 6 The Mute buttons below will cut the corresponding channel The Phase Invert buttons determine the polarity of the output either Normal or Inverted e The HPF LPF for each channel is at the bottom of the window Users can enter the value for the frequency in the number box or click the corresponding triangles in the frequency graph to manipulate it This applies for both HP and LP The drop down menus for the HP LP allows the user to choose the filter type Bessel Butterworth or Linkwitz Riley from 6dB Octave curve to 24dB Octave Below the HPF LPF there is a gain and delay control on each channel The gain from 48 00 mute to 12 00dB for level adjustment and delay from 0 to 20ms 21 User Manual Digidrive V2 VH pal Input A D e Each input tab contains EQ Limiter Gain and LPF HPF controls Every individual EQ in the 10 band EQ allows frequency control from 20Hz 20kHz gain 12dB and Q from 0 2 to 25 0 for
9. 20Hz and 20kHz with the number box and the drop down menu chooses the type of filter Butterworth Bessel Linkwitz Riley from 6dB Octave to 24dB Octave e The gain fader on the right hand side of each output tab relates to the fader in the Main tab s mixing matrix If the gain is changed in either of these windows it will affect itin the other 23 User Manual Digidrive V2 VH e The delav control ranges from Oms to 20ms e The limiter on the output is there to stop and unwanted clipping from high peaks in the audio e The mute button is linked to the mute button on the main tab and will cut the channel The invert button is linked to the phase invert on the X over tab and will invert the polaritv of the signal When the button is blue phase is inverted e The top left hand part of the output window is the Input Mixer This part of the output tab allows the user to route anv input A D to anv output from 48 00dB mute to 12 00dB with the gain fader in the mixing matrix NOTE The Input Output EQ windows can be saved as a png picture file by clicking the camera icon in the top left hand side of the graphical EQ window in the Input Output tabs There is also a magnifying glass icon which allows users to set more precise values for the EQ and a full screen icon which when pressed once fits the EQ window to the Live Link window and when pressed again sets the EQ window to full screen view To exit full screen press the X
10. ETTRE 21 1672 MOVE E 21 16 30 Input A Dioni ld 22 7 06 4 Qutput 1 6 NO 23 TC SD OT SO TEE 24 8 0 Specifications E 25 9 0 Block Diagrams tret t NEEN a a ae 26 10 0 Menu Structure 222 cose dd Ee dE RANNER AA ENER SES NEEN KERVENE A 30 A TO 31 11 1 Worldwide Service 31 11 2 Warranty Registration ss sse nnenennnenennnn 32 11 3 Environmental sssenezsnzinenszoteniznziszeossesokenzaareenekoszzni 32 12 0 WarrantV AAA 33 7 User Manual Digidrive V2 VH Mor Introduction to Digidrive V2 The Void Acoustics Digidrive V2 is a full 4 input 6 output digital loudspeaker management system designed specifically for live sound touring fixed installations stage and theatre productions bar and club and conference applications Through matrix mixing any input can be routed to any output at any level using high quality 24 bit A D and D A converters with the latest 64 bit processors allowing unparalleled bandwidth from 5Hz to 45kHz Inputs A amp B are analogue C amp D being digital AES EBU which can handle clock speeds of up to 192kHz Each input and output on the Digidrive V2 includes a 6 12 18 24dB HPF and LPF that can be set anywhere between 20Hz 20kHz as Bessel Butterworth or Linkwitz Riley filter types There is also control of 10 EQs per Input Output channel with filter types bell allpass notch or high low shelf Connected via USB or Ethernet to a Windows Mac OSX PC the Digidriv
11. NOIA Digidrive V2 User Manual Digidrive V2 VH ees eege a ia ge Ee Quick Start This quick start guide offers a simple way to set the Digidrive V2 up in a practical application NOTE make sure you know the limitations of your loudspeakers before setting up a system with the Digidrive V2 Also ensure that the unit and all power amps are powered off before making any connections to from the Digidrive Always make sure that power amps are the last units turned on and the first units turned off 5 e Connections e Ensure power is off to the device and power amplifiers connect the output signal from the sending device mixer via XLR to Input A mono signal or Input A B stereo signal Connect appropriate connections from the output XLR connectors to the power amplifier s depending on the routing configuration suitable to the loudspeaker system Eg 1 way Outputs 1 2 full range of frequencies e 2 way Outputs 1 2 LF Outputs 3 4 HF 3 way Outputs 1 2 LF Outputs 3 4 MF Outputs 5 6 HF NOTE There are many more routing options than the examples above but these options are basic configurations for beginners All frequencies to amp 2 User Manual Digidrive V2 VH e Once all connections are made vou are readv to begin the set up of the svstem NOTE For this example the routing used will be for a 3 wav svstem using only the Digidrive V2 unit LU iia Step by step
12. Worldwide Service Service may be obtained from your local authorised service centre To obtain service simply present your sales receipt as proof of purchase along with the defective unit to an authorised service centre They will handle the necessary paperwork and repair Remember to transport your unit in the original factory packaging 1 When sending a Digidrive V2 to an authorised service centre for service please write a detailed description of the fault and list any other equipment used in conjunction with the faulty product Send the fault description with the faulty product do not send it separately 2 Ensure safe transportation of your unit to the authorised service centre Ship it in the original factory packaging if possible 3 Do not ship the unit in any kind of rack Ignoring this warning may result in extensive damage to the unit and the equipment rack Accessories are not needed Do not send the instruction manual cables or any other hardware 4 Before returning your faulty product for repair please remember to get a return authorisation number from the dealer whom you purchased your product from Failure to do so could delay the repair of your product 31 User Manual Digidrive V2 VH uh tess Warranty Registration Please take time to fill out the warranty registration form at the back of this manual and return it to Void Acoustics Lu EN Environmental WEEE Mark
13. are linked as a stereo pair In AB Link On 14 User Manual Digidrive V2 VH DR A Output Menus Each output channel has a set of Menus for specific parameters accessed with the PAGE and PAGE buttons Gain refer to Input Menus Delay Oms to 20ms in 0 01ms steps Depressing the control wheel units can be changed to feet or mm Out 1 Delay 00 000ms e Low Pass refer to Input Menus e High Pass refer to Input Menus e PEQ 1 10 refer to Input Menus e Limiter refer to Input Menus e Phase can be normal or inverted polaritv Out 1 Phase Normal Link select whether outputs 1 2 are linked as a stereo pair Out 12 Link On 15 User Manual Digidrive V2 VH GAL A MAGER System Menus The system menus show information about the device and allow the user to change some system parameters These menus are accessed by pressing the MENU button repeatedly To return to the main page the EXIT button is pressed 16 Load shows the program 1 100 and the first 16 characters of the program name Load the preset by depressing the control wheel Load 1 XXXXXXXXXXXXXXXX Save stores the current settings to the designated program 741 100 by depressing the control wheel Users can set a custom name for the program with a combination of the control wheel and control wheel button To delete a character the EXIT button is pressed to cancel storing a program all characters must first be deleted and then the EXIT
14. button pressed Save 3 EMPTY Set Presetname XXXXXXXXXXXXXXXX User Manual Digidrive V2 VH e Access Level Unlocked or Locked This allows the user to secure the unit and prevent changes on the device To lock unlock the device a password is required by depressing the control wheel To delete a character whilst entering a password the EXIT button is pressed Press the menu button once the password has been entered to confirm it and then again to set it Access Level Unlocked NOTE Locking the unit will lock any parameters from being changed To unlock the unit in order to make further changes use the same process required to lock the device with the same password entered e Version Info IP Address MAC Address information for the user about the device Includes Serial Number software version hardware version IP address and MAC address Version Info SN XXXXXXXXXXXXX IP Address XXX XXX XXX XXX Routing changes the configuration of the device Out 1 Out 2 Stereo way Stereo 2 way In Stereo 3 way In1 3 channel 1 way 3 channel 2 way In 4 channel 1 way Mono 4 way Any 17 User Manual Digidrive V2 U O l D VQ ennen Live Link Control Interface The Digidrive V2 is enhanced by the Live Link software for Windows and Mac OSX which allows the user to have real time remote control via either USB or Ethernet Utilizing this software makes using the Digidrive V2 easier for t
15. connected All Units 1 unit online is shown and beneath it the Digidrive V2 and information Le the reference address To access the Digidrive V2 s main control window press the gt gt button Void Network Control Software bo E ka File Tools Help Info Name Reference Address Group Launch MO ll All Units 1 units online Close mi UB ko Name 00 05 A4 22 96 88 USBport3 Not Grouped xl p pda ssk ens inbena ka kud RR Digidrive V2 Control Window Within the main control window there are 12 tabs for control of the 4 inputs 6 outputs crossovers and the main window Note any changes made to any parameters on Live Link whilst the Digidrive v2 is connected will change the same parameter on the device If the device is disconnected and the changes weren t stored the data will be lost from the device 20 User Manual Digidrive V2 WOIA TO A AT Main A mixing window for all inputs outputs so a user can use the faders to adjust the level of the inputs outputs relative to one another from 48 00dB mute to 12dB There are Mute buttons below each fader which cut the corresponding channel red when active as well as Link buttons which join two channels A B C D 1 2 3 4 5 6 together to form a stereo pair Users have store loading options both for the device and the PC on the software under Local Presets users can store load a program from to their computer and under Unit Presets users can
16. e v2 can be controlled from the front panel or through the purposely designed Live Link software and can be set up with an IP address on a network in order to run multiple devices Shipping contents Digidrive V2 unit User manual USB cable Live Link software CD Power cable NOTE Be sure to check for any missing items or damage when opening the box If this does occur please immediately contact the Void distributor where the product was purchased from or contact Void directly 8 User Manual Digidrive V2 VH PO A A Features 4 Inputs 2x Analogue 2x Digital AES EBU amp 6 Outputs with matrix mixing 64 bit DSP High quality 24 bit A D amp D A converters USB Ethernet interface for remote control configuration ona PC 10 EQ bands per Input Output channel Accurate control of delay level polarity and limiters Full range of crossover control parameters Ability to program amp store up to 100 preset Security lock CPU and DSP upgrades via PC User Manual Digidrive V2 VH A o EREE A ida M Front Panel 56 1 USB Port standard Type B female socket 2 Peak Level LED shows the current peak of the signal SIG 6dB Limit Clip Input s Limit Max headroom Output Limit threshold of limiter 3 Menu amp Control Keys CH SELECT Previous channel CH SELECT Next channel PAGE Previous page PAGE Next page MENU System information EXIT Return to main
17. each channel which is visually represented in the graph above Each EQ can be manipulated left clicking on the respective square in the EQ graph and dragging with a mouse The Q can be changed by right clicking the respective square and dragging from left right Below the EQ matrix is the HPF LPF controls The number box sets the frequency 20Hz to 20kHz and the drop down menu chooses the filter type Butterworth Bessel Linkwitz Riley 6dB Octave to 24dB Octave e The gain fader on the right hand side of the window coincides with the fader in the Main tab s mixing matrix as well as the mute button The delay control offers a delay from Oms to 2000ms but the units can be changed to feet inches mil meters millimetres and seconds To the right of the delay control there is a limiter to ensure that clipping does not occur when the signal goes above the set threshold between 48 00dBu and 12 00dBu The release can be set between 1ms and 100ms The limiter on the output is there to stop and unwanted clipping from high peaks in the audio The mute button is linked to the mute button on the main tab and will cut the channel The invert button is linked to the phase invert on the X over tab and will invert the polarity of the signal When the button is blue phase is inverted The top left hand part of the output window is the Input Mixer This part of the output tab allows the user to route any input A D to any output fr
18. eseuound jo ayeq JB9JJBAO SS9JPPB y oj JI pues pue ped SIU yo no pue pues UOIJEJJSIB9J A JUBJJEM siy ajajdwoo aseald JoNPOJA Don siu Buiseuound JO no xueu TION uoneusibey AJUEJJEM Void Acoustics Unit 15 Dawkins Road Ind Est Poole Dorset BH15 4JY UK Digidrive V2 User Manual WOIO
19. he Digidrive V2 The Digidrive V2 can be connected to a PC via USB or Ethernet network Connection via USB requires the provided USB cable to be plugged into the front of the Digidrive V2 and any USB port on the PC When connecting the Digidrive via Ethernet to the PC an IP address is required for communication between the device and the PC So connecting the Digidrive V2 to the computers network router will assign an IP address automatically through the networks DHCP This configuration is useful for installations where there will be more than one device controlling the system as users are able to connect the devices to a network and control each of them separately from one PC connected to the network by Ethernet or wirelessly 19 User Manual VI NOTE To configure a manual IP address when connected via Ethernet on the main window of Live Link go to the top menu bar Hardware gt Configure gt Network Digidrive V2 LA a a TA Starting Live Link To open the Live Link software in Windows find the icon either on the desktop and double click The program can also be found in the start menu gt Void gt Void DSP Control and through Windows Explorer To open the Live Link software in Mac OSX find Void DSPControl app in the applications folder in Finder or in the applications folder in the dock e Ee Using Live Link Once the software has opened the Void Network Control Software window is shown If the Digidrive V2 is
20. he user to manipulate and monitor the device as it provides more accurate control over each parameter Link 0 LO e oo 0 00 0 00 0 00 3 00 3 00 0 00 0 00 3 50 I 3 50 Mute Users have separate tabs for each Input and Output channel as well as a tab specifically for the crossovers which with the Graphical User Interface GUI makes it easier to physically see the changes in LPF HPF or EQ Also the limitation of 100 preset programs on the Digidrive V2 does not necessarily B apply when using the Live Link software as more programs can be created and stored even when the device isn t connected The device must be connected in order to write modify programs on board Input Mixer ww EN 18 User Manual Digidrive V2 VH CN EE Minimum System Requirements e Windows XP with service pack 2 7 or Mac OSX 10 5 8 or higher e USB or Ethernet port for connecting the Digidrive V2 to the PC Pentium 4 or higher VD EE Installing Live Link Windows e Insert the included CD into the PC e Follow the instructions on the Setup Wizard carefully Once the installation has finished close the Setup Wizard and remove the CD to begin Mac OSX e Insert the included CD into the PC e Double click on the disk on the desktop to open the files and open Void_DSPControl mpkg e Follow the instructions in the Setup Wizard When the installation has finished eject the CD e A Connecting t
21. icon The T icon shows the information for the EQ previously changed NOTE When moving a certain band in the graphical EQ window holding CTRL and clicking will limit movement to horizontal for Freq and Q Holding Shift and clicking will limit movement to vertical for Gain TAM Ee E Upgrade To upgrade the firmware on the Digidrive V2 in the top menu bar go to Hardware gt Firmware Update and follow the instructions NOTE Updating the firmware on your device will erase all data presets on it It is highly recommended to back up all presets before performing an update 24 User Manual Digidrive V2 VH Bender a AA eege Specifications inputs EEE Outputs 6 channels maximum output level 12dBu ao ar ey J Butterworth Linkwitz Riley Bessel HP LP Out Output Limiters Threshold 50 to 12 dBu Attack Time predictive Release Time 1 100ms Equalisation 10 EQ s for each output 10 EQ s for each input Bell filters with a Q of 0 20 to 25 Range 20Hz 20kHz Amplitude of 12dB Hi amp Lo Shelf filters Fully adjustable Notch and Allpass filters Inputs up to 2000ms Outputs up to 20ms Power Input IEC 230 VAC 50Hz FEE Ta mr 9 Wem e m 9 Depth 167 mm 6 57 Weight 2 87 kg 5 22lbs 25 User Manual Digidrive V2 U O D 9 0 DT Routing Diagram All freq Left All freq Right Stereo 1 way configuration using 1 power amplifier for all freq
22. om 48 00dB mute to 12 00dB with the gain fader in the mixing matrix 22 User Manual Digidrive V2 VH NOTE The Input Output EQ windows can be saved as a png picture file by clicking the camera icon in the top left hand side of the graphical EQ window in the Input Output tabs There is also a magnifying glass icon which allows users to set more precise values for the EQ and a full screen icon which when pressed once fits the EQ window to the Live Link window and when pressed again sets the EQ window to full screen view To exit full screen press the X icon The T icon shows the information for the EQ previously changed NOTE When moving a certain band in the graphical EQ window holding CTRL and clicking will limit movement to horizontal for Freq and Q Holding Shift and clicking will limit movement to vertical for Gain 7 6 4 i eA VET SS SANS RSA Output 1 6 D Each output tab contains control of 10 EQs a Limiter Delay LPF HPF Polarity Gain and an Input Mixer e The EQ is the same as the EQ for Inputs A D with a 20Hz 20kHz frequency range 12 00dB to 12 00dB range of gain and a Q from 0 20 to 25 00 Changing anv of the EQ settings is represented in the graph above the EQ control matrix Using the mouse left right clicks and dragging the EQ square in the EQ graph users can physically manipulate each EQ band s frequency and Q D Along the bottom of the window if the HPF LPF these can be set anywhere between
23. peakers or any other consequential damage resulting from breach of any written or implied warranty VOID WARRANTY PROVISIONS Void will remedy any defect regardless of the reason for failure except as excluded by repair or replacement Void will remedy the defect and ship the product within a reasonable time after receipt of the defective product at an Void Authorised Service Centre TO OBTAIN WARRANTY SERVICE In the event that a Void product requires service the Owner must contact Void or an Authorised Void Service Centre to receive an R A N Return Authorisation Number and instructions on how to return the product to the Void Authorised Service Centre or to the factory Void or its Authorised Service Centre will initiate corrective repairs upon receipt of the returned product Please save the original carton and all the packing materials in case shipping is required All products being returned to the factory or service centre for repairs must be shipped prepaid If the repairs made by Void or the Void Authorised Service Centre are not satisfactory the Owner is instructed to give written notice to Void If the defect or malfunction remains after a reasonable amount of attempts by Void to remedy the defect or malfunction the Owner shall then have the option to elect either a refund or replacement of said Void product free of charge The refund shall be an amount equal to but not greater than the actual purchase price not including any taxes
24. uencies 26 User Manual Digidrive V2 U O l D EF LF 20888809 MHF Right Stereo 2 way configuration using 2 power amplifiers for Low Frequencies and Mid High frequency bands 27 User Manual Digidrive V2 U O D LF Left LF 1999899959 MF Left Out 6 MF Right HF Right Stereo 3 way configuration using 3 power amplifiers for Low Mid and High frequency bands 28 User Manual Digidrive V2 U O l D Out 4 HF from Out 4 MM LJ M Mono 4 way configuration using 3 power amplifiers to drive Low Low Mid High Mid and High frequency bands 29 User Manual Digidrive V2 VH lr RV BEEN Menu Structure Input A D Ouput 1 6 CH SELECT PAGE PAGE MENU Load Load Preset Save Input C Save Preset Low Pass Access Level Ouput 1 Enabled Enabled Version Info IP Address Output 2 High Pass MAC Address Enabled Output 3 Routing Output 4 Output 5 Enabled Output 6 Threshold Release Phase NOTE To access each Sub Menu depress the control wheel to cycle through 30 User Manual Digidrive V2 VH WA GE Service This unit has very sophisticated circuitry and should only be serviced by a fully trained technician No user serviceable parts inside Refer servicing to a qualified technician 1121 A A dea
Download Pdf Manuals
Related Search