Tubular motor receiver TM5801 series user manual
Contents
1. 60 times minute ON Deadman 9 2 l operating direction of motor OFF Three button control OFF Lamp keeps lighting OFF Impulse iv Operation Instruction 1 Learning transmitters Press the learning button in the control board LED is on enters into the learning process Press the same button twice LED blinks for several times then off The learning process is successful 2 Erasing transmitter Press the learning button continue pressing for 8s until LED turns off Release learning button LED will be on about 1s and then off the erasing process is successful 3 5elf learning function Old one Old one New one STEP2 then press en press STEP3 Press the same button on j d m STEP 1 Use the trasmitter that button 2 to let it z i PEARS m I the new transmitter twice The l already has been learned as old i enters into the ie i d l z i learning process done In this m i transmitter press button 1 and learning process a E E ji way new transmitter can be button 2 at the same time a ae learned without pressing the learning button on the control board 4 Remote control Instruction 4 1 Three button non latch control system Function select switch 2 at OFF 4 at OFF Button 1 2 3 in transmitter is in correspondence with open close and stop The same as button on controller and the external button 4 2 Three button latch control system Function select switch 2 Jat OFF 4 Jat ON Motor works clock2. TM5801 series user manual A2 Tubular motor receiver TM5801 series user manual I Technical parameters 1 Working voltage 85 265VAC 110VAC 60HZ 220VAC 50HZ is optional according to motor 2 Temperature range 20 C to 60 C 3 Loading capacity 1HP 220VAC or 0 5HP 110VAC 4 Built in fuse 10A motor 0 5A Self healing 5 Working frequency 433 92MHZ 6 Transmitter stored 30pcs 7 Size 180 61 150mm 8 External infrared protection connects NC contact 9 External switch open stop close in a loop 10 Running time adjustable 5S 100S Safety Instruction 11 External flash lamp working voltage 110VAC 220VAC remains the same as motor 12 PVC button open stop close 13 Function select switch DIP1 change the running direction of motor DIP2 Switch for single button remote control and three button remote control DIP3 switch for blinking and lighting of lamp Frequency when blinking is 60 times per minute DIP4 switch for latch and non latch of remote 14 Output voltage DC12V 0 17A For security please read the instructions carefully before initial operation making sure the power is off before connection Please clear the memory before initial operation Ref Erasing ALL learned memorized transmitters Do not learn the remote control when the motor is operating in order to avoid mis operation The received signal may be interfered by other communication devices e g the wireless control syst
3. em with the same frequency range It is forbidden to control the high risk coefficient equipment system e g cranes It is used only for the manual remote control and wireless control equipment system which must not endanger life or property during running failure or its security risks have been eliminated Connection Instruction As it shows in the picture 1 AC input working voltage is 85 265VAC 2 COM DOWN UP connects AC motor 3 Flash lamp working frequency is 60 times per minute User can select lighting or blinking by setting up DIP3 4 Photocell port is NC device provide 12VDC power for photocell photocell only work when door closing contactor should be short circuit if not use it 5 External switch UP STOP DOWN are NO function is the same as the way controlling with remote control button Learning button Learning indicator light POWER Indicator Time set up button com External Control Stop button aton switch butt Open a sag Ly Photocell a 8 a a w a S arts E PVC button port Gea re oe 12VDC TM5800V5 Gl aul 12 PR power 0 54 Self healing fuse 10A fuse I AC power input Lane Motor firing line null line ground wire ground wire External flash lamp TM5801 series user manual A2 6 Function select switch ON OFF DIP1 DIP2 DIP3 DIP4 i ON or OFF can change the current ON Single button control ON Lamp keeps blinking
4. ly if longer than 1005S 3 A a Vin control panel and OPEN STOP CLOSE button in transmitter are in correspondence with open close and stop V TM58XX series model list
5. wise when keep pressing button 1 Motor works anticlockwise when keep pressing button 2 Motor stops when releasing button 4 3 Single button non latch control system Function select switch 2 at ON 4 at OFF Press Open motor works clockwise press stop press close motor works anti clockwise press stop and so on in a loop Single button control is only effective to the learned button if a new button of transmitter learned into the control panel the formal one is useless e g if learned button at first and then button D or G the former button D becomes invalid 4 4 Single button latch control system Function select switch 2 at ON 4 at ON Motor works clockwise anticlockwise when keep pressing the button motor stops when releasing 4 5 Infrared sensor protection It only work when door closing Motor stops when photocell signal disconnecting during door closing 4 6 Motor running time set up Motor running time is adjustable from 5s to 100s It is adjusted by TIME button press TIME and LED DL2 will blink after 5s then release the button after the pre set time is appropriate The time between pressing and releasing the button is the motor running time controller will stop the motor when time is up Note 1 Single button control only for remote control PVC button in controller A A is to open close stop 2 Max running time means that the motor s maximum running time at a time is 100S the motor stops immediate
Download Pdf Manuals
Related Search