"user manual"
Contents
1. A name that is given to a specific channel number Channel Memory Where channels are stored after they have been placed in memory Channels can be added or deleted from channel memory Commerical Skip A feature that allows the viewer to scan other channels during commercials and return to the original channel after a timed break Component Device such as VCR laserdisc player audio equipment camcorder etc Disabled Turns off feature Display A word words or graphics that appear on the TV screen Inputs Located on back of the TV for connection of a component to the TV Used to route signals into the TV from components Jacks Connectors located on the back of the TV for connecting antennas or other components Menu A listing of features controls and adjustments shown on the TV screen that can be changed Mono Slang for monaural Sound comes through one channel On Screen Display See Display Outputs Located on back of the TV for connection of another component Signals are routed out of the TV into the other component Picture in picture A feature that allows you to watch two channels at the same time a small picture within a big picture The smaller picture comes from a VCR or other component connected to the TV Picture Reset Returns all of your TV picture adjustments back to the factory setting PIP Short for picture in picture Sharpness Clearness of a picture2. REC Record Starts recording onto tape STOP Stops tape or laserdisc PAUSE Pauses tape or laserdisc component VCR2eLD can only be either a VCR or a Laserdisc Player Cable Box Laserdisc Player and Audio Cable Box Laserdisc Player and Audio DISPLAY Shows displays on the screen Clears menus from the screen SKIP Commercial Skip Allows you to scan other chan nels during commercials Each press adds 30 seconds TV switches back to original channel when time runs out Press CLEAR to cancel SKIP CHAN and v Channel up and down Scans up and down through channels in the TV s memory Moves through channels in VCR s memory VOL and Volume up and down Raises and lowers sound MUTE Switches the TV sound on or off PREV CH Previous Channel Changes back and forth between two channels Select a channel and then select another Press PREV CH to switch between the two channels Using Your TV and Remote With Remote Buttons Number Buttons 0 9 MOVE lt and gt left and right Selects any channel number Moves left and right on a menu line See Menu Basics on page 5 power VERT DSSOCABE p Two numbers must be pressed for Chan ene each channel Press 0 and 6 for ges a feature seting VCR2 LD AUDIO channel 6 For three digit chan nels press and hold 1 until 1 MOVE A and Y up and down Moves up and down menus See appears on the screen Then press Menu Basics o
3. KONG Important Information W ARNING To reduce the risk of fire or shock hazard do not expose this TV to rain or moisture VAINA eR To reduce the risk of electric shock do not remove RISK OF ELECTRIC cover or back No user serviceable parts inside Refer SHOCK DO NOT OPEN servicing to qualified service personnel This symbol indicates This symbol indicates dangerous voltage inside the important instructions product that presents a risk of accompanying the product electric shock or personal injury Caution To reduce the risk of electric shock match wide blade of plug to wide slo fully insert Attention Pour viter les chocs lectriques introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqd au fond Refer to the identification rating label located on the back panel of your product fo its proper operating voltage FCC Regulations state that unauthorized changes or modifications to this equipmet may void the user s authority to operate it If fixed non moving images are left on the screen for long periods they may be permanently imprinted on the screen Such images include network logos phone numbers and video games This damage is not covered by your warranty Extend viewing of channels displaying these images should be avoided Cable TV Installer This reminder is provided to call your attention to Article 820 4 of the Nationa Elect
4. SKIP Signal Electrical waves that are sent or received through cables or through the air See Commerical Skip Sleep Timer A feature where the TV can be set to turn off at a specific time within four hours Source s Components or devices that are connected to the TV Stereo Sound signals that come through two channels left and right Tone Quality of the sound Tuner A device that receives and selects signals The desired signal is selected by the tuner Unusable Signal A message that shows no signal is coming in on the video input Video Picture reproduced by the television 35 36 References Index A Adding Channels to Memory 20 Adjust Menu PUMTOCOIOR ainn ea oire 17 Drio Nissinen 17 COLOFN 17 Picture Reset 000000nnnen0000nns 17 Sharpness iscissi 17 WAR E T E OE 17 Adjusting i 5 2 bo 9 nn aan 16 Picture Settings ecciesie 17 Sound Settings eee 18 19 Air or Cable Feature 27 Alarm Chaninnel ccceccccccsseseees 23 Alarm Clock sessosoeososesecesssssrsoss 23 Alarm Displa Yessie 29 Alarm Menu cecccscecseossesece 23 Alar aaa a 23 Alarm Channel 23 ON Tie so 23 On TING n aa 23 DCE C lockarna 3 ANTENNA Button ccc ecceeees 7 Antenna eana 27 35 PUCIO sonoran 6 15 18 19 35 AUDIO Button eee 6 15 Audio Codes ccccccecsesececesesronevess 15 Audio Equipment Buttons 15 Audio video cables c 08 35 AUtOCOlOR w
5. work with your equipment Basic Operation D Turn the audio equipment off using the audio component s power off button Audio Codes RCA Dimensia 15 16 Adjusting Your TV Overall Picture Follow the steps below to lighten or darken the overall picture without changing the color levels 1 Select the Controls Menu Alarm Adjust Setup Sieep Timer 2 Highlight Picture 3 Use MOVE P gt and lt to adjust the Picture Picture Press MENU PROG to select the Controls menu This menu is yellow Press MOVE down to high light Picture Press MOVE gt right to lighten the picture OR Press MOVE lt 4 left to darken the picture Adjusting Your TV Picture Settings Follow the steps below to change the picture on the screen to your personal setting The chart at the bottom of the page explains your options 1 Select the Adjust Menu Press MENUsPROG repeatedly to select the Adjust menu This menu is light blue 2 Highlight item to change Press MOVE down to highlight the picture item you want to adjust 3 Use MOVE P or 4 to adjust each item Press MOVE P or lt to adjust each item lt t Press MOVE P to Press MOVE 4 to EAAS Give red tint to skin color Give green tint to skin color Bright Brightness Add more light to dark parts of Add more dark to light parts of the picture the picture Sharp Sharpness Sharpness _ Show
6. 24 25 Using the Remote Audio Equipment 15 Cable BOX ii isesssscsisiscsssscaveesees 12 13 Laserdisc Player sssssssee 14 Satellite Receiver ccseeces 11 VOR eee eee 8 9 10 V VCR TU Oln 10 TUN ON aciei esasa resina 10 Record one TV program and watch another cesses 10 Watch a tape rsccsosssserersssees 10 VCR1 Button sscssesessens 6 8 9 10 VCR 1 Channel ssoesosesesoseseseseses 9 VCR2 LD Button 0 6 8 9 10 VCR Codes siciititecspasiccsiriinsanaans 8 VCR ButtonS eeesseseseroeesssssssesesere 6 7 VIdeo sene 35 VIDEO 00 Display cssssses 29 Volume Display csssesssseen 29 VOL and Buttons RE OE sorea naini 4 6 TV en ariostace rena 28 W Waming so cssescsqssdcasideadensiuessestoenassenee i Warranty ios cscescstuaceeiccsstocecosecensteces 32 Watching Closed Captioning 26 Watching Picture in Picture 24 25 37 PROSCAN An RCA Entertainment Product fA THOMSON CONSUMER ELECTRONICS 10330 North Meridian Street Indianapolis IN 46290 1998 Thomson Consumer Electronics Inc Trademark s Registered Marca s Registrada s Printed in Japan TOCOM 15336310
7. 44 45 46 52 Canon anaa ares 08 53 Capehartin 01 Citizen eee 07 09 13 44 45 46 52 Colortyme isis cds sees oveepantenestansiets CT AIS uina ie eNA 07 12 Curtis Mathes ccc08 00 07 08 14 T a 15 44 46 53 64 67 Daewoo eessesssssoneerrirserossssnenss 13 45 52 76 ra 29 EELEE EAEE EREN A 14 16 Dimensia eessssrnrcoessorsssenseuasssesssoosorosss 00 Dynatec Manisa a 15 Electrohome ccccceesesseccsasscsssseeenes 27 Emerson 08 09 10 13 15 20 23 27 OAN 34 41 42 47 49 57 62 65 67 68 70 Fisher 0cces00 02 12 18 19 43 48 58 Funa aaee aE eca SE Sian neue 00 07 08 32 37 53 Goldstar ccccccssccssccceseces 09 14 46 60 Harman Kardni cccsccsssssssesenees Pita Cl aeee isir 05 15 35 36 Instant Replay cscsscessesesneeeesees 08 NG Liew adnan ence end g i 7 CoN ee oTo lt PA Biv Q Q 2 ae gt 2 Q WO ariani 02 14 16 30 46 74 Kenwood oveessscsseesconeees 02 14 16 30 44 46 1 ih REE E E A ET 73 Lloyd eesti cir 5 TO AM rai 31 Magnavox ecsscccecceeeseesrenes 08 29 53 56 Maranitz 02 08 14 16 29 30 44 46 61 Mara ist ee ead oO ME ee eee nee ve oe Se 08 Memorex ssssscsssssssessesseen 08 09 12 15 e T ica eect ated 04 27 Midland aiioa a aR 32 Minolta snaa 05 35 Mitsubishi 0 04 05 27 35 40 Montgomery Ward csssscssssererees 06 mere Mere re 07 15 Mulltitech cscosssssssssss
8. 7 14 Laserdisc Player sssssseers 14 M l Menu sinasa ETERNE ETRA 35 MENU Buttons cccccceeeeees 4 5 Ments eiiaoe aire eNA 5 Menu Colors cccssssssssssesssessseees 5 MONG rorarii sn 18 35 MOVE PIP Button 00 7 25 Moving through the Menus 5 MUTE Button ccccssscssssevees 6 Mute Display sse0 Ree References Index N Naming the Channels 21 Number Buttons ccccscsssossssnees 7 O Off Time Alarm sccsscsssesers 23 On Screen DisplayS 00 29 35 On Time Alarm cscseseessees Order Form for Parts 33 34 OE US ET E AE E P PAUSE Button sseesesessoososssossessses 7 Pice ane 16 17 Picture Adjustments 16 17 Picture in Picture 4 7 24 25 Change Channel sss0 24 TO ON crcire rdar 24 T r Olf osea 25 Use PIP Buttons ccccccens 7 25 Picture in Picture Buttons 7 Picture Settings sscssessees 16 17 Picture Reset cccccsssssscceesccees 17 PIP ieren a 4 7 24 25 PIP ButtOnvesccasssissicscssicvctense 4 7 24 25 PIP 00 Display sesessesossorossereseersse 29 PIP MOVE Button cc008 7 25 Place Channels in Memory 3 20 PLA Y Button siscssscccsesssvscscceisscscesses 7 Pl g in TV esnea e 2 POWER Button c0ccsseesseees 2 6 Power BultttoOms cscccccsssssvccees 2 6 PREV CH Button ececeoees 6 Previo
9. page 2 Unplug TV for a few minutes and then turn it on again Check antenna connections Check position of Cable Air feature See page 27 Try another channel Inactive channel may be tuned Make sure component connected to the VIDEO INPUT jacks is turned on if you choose channel 00 Make sure TV is tuned to the same channel as the switch on back of VCR if watching a VCR Make sure TV VCR button on VCR is in correct position when using VCR Try another channel Scan the channels Check antenna connections Adjust TV picture See pages 16 17 Make sure small picture is tuned to channel 00 Make sure the component connected to the back of the TV is turned on Make sure a video cable is also conntected to the TV s VIDEO INPUT jack if using an S VHS component Make sure the AUDIO and VIDEO OUT jacks on the VCR kaserdisc player or Camcorder are connected to the TV s VIDEO and AUDIO IN jacks Make sure VCR 1 Channel is set to Disabled See page 9 Make sure a video cable is also connected to the TV s VIDEO INPUT jack References Trouble Checks Trouble Remote Buttons don t work when you press them Works part or none of the time Can t select certain channel Sound Noisy stereo reception Picture okay no sound Picture okay sound poor No stereo on stereo station TV Turns on or off Turns off by itself Turns on by itself Does not turn off at Alarm Time Checks and Adjustments Pres
10. C Diagram used fromthe Connection Guide 1B 1C 2B 2C 3B 3C 4C 5C 4B 5B Set VCR1 Channel to 00 3 or 4 same as 3 4 switch 10 Using Your TV and Remote With VCRs Basic Operation If the remote operates your VCR this page and the next shows you how to use it for basic functions See page 7 for more details on buttons used with your VCR Turn on the VCR A Press channel 00 on the TV to see what the VCR is doing B Press VCR1 or VCR2eLD to set CRI DSSecag got o O a4 the remote to control the VCR VCR2 LD AUDIO C Press POWER to turn on the Q VCR if it did not turn on when you pressed VCR1 or VCR2eLD Turn off the VCR STOP PAUSE A Press VCR1 or VCR2 LD to set a a the remote to control the VCR O O B Press POWER lt Record one TV program O A Press VCR1 or VCR2 LD to set and watch another O O the remote to control the VCR Q PREV CH Q 30 5Q O sQ O ANTENNA Q amp A o gt PIP SWAP A OQ v Q9 ch Watch a tape in your VCR B Tune the VCR to the channel you want to record using CHANNEL up and down or pressing two number buttons C Press RECORD to start recording D Press TV VCR on the VCR E Press TV to set the remote to control the TV F Press CHANNEL up or down to change channels on the TV G To see the channel you are recording tune the TV back to channel 00 A Turn on VCR B Insert a tape in the VCR C Press
11. O onnaa aa 17 Colors Menus cscccsccsscssseesseees 5 Commerical Skip 6 29 35 BUON ta 6 DISDIAY cinneann 29 COMIPONGNE asiron skissa 35 Component Buttons AUDIO DSS CABLE VCR2 LD VCR1 Components Audio Equipment 00 15 Cable Box nce 12 13 Laserdisc Player 14 Satellite Receiver sseesssesees VOR elite sensi 8 9 10 CONENIS oiiro a 1 Controls TV Front Panel ssesnenseseeresee 28 Remote in S 6 7 Controls Menu Closed Captioning 26 PACER aian E E 16 Sleep Timer PAP ped 8 o E rr ne 18 TONE siete cleecsas estes ces a 18 D Delete Channels from Memory 20 Disabled oorner 35 DISPLAY Button 6 29 Displays On Screen 00 0 29 Alarm Channel Name Channel Number Commerical Skip Mute PIP 00 Sleep Stereo Time Unusable Signal VIDEO 00 Volume DISPLAY Button 0 ce 6 29 E Erase a Name ccccccesesssseeeee 21 Erasing Channels from Memory20 EXPAND Button cccssseseeuees 7 F FF Fast Forward Button 6 Front Panel Controls 5 28 FREEZE Buttom ccsecee 7 25 G Glossa esna 35 Guide COLORS uaa 5 Menu Buttons ccccecen 4 5 Moving through the Menus 5 ih eerie EE 2 3 4 5 Hook up TV Connections Guide I INPUT Button scitteasicctueccs 7 MPU oent 35 TACKS ettii J T aa 35 L Laserdisc Player Codes 14 Laserdisc Player Buttons 6
12. PLAY to start the tape playing D Press STOP when you are finished E Press REW to rewind the tape Using Your TV and Remote With a Satellite Receiver Basic Operation You may also be able to use the TV s remote with other satellite receivers Refer to your Satellite Receiver owner s manual to hook up your Satellite Recerver The remote may need to be programmed for other brands of satellite receivers but may not operate all models of the brands listed below Use the codes below or on the sheet packed in with your remote Follow the instructions below for basic operation of your receiver You may also want to experiment with other buttons on the remote to see if they work with your receiver Program the remote for your Satellite Receiver power VERT DSSOCABE py q O O lt I gt gt Turn on the Satellite Receiver Turn off the Satellite Receiver Satellite Receiver Codes A Point the remote at the satellite receiver and hold DSSeCABLE Enter the code for your brand from the code list below Release DSS CABLE Press POWER If nothing happens try pressing DSSeCABLE and then POWER Press DSSeCABLE to set the remote to contro the satellite receiver Press POWER to turn on the receiver if it did not turn on when you pressed DSSe CABLE Press DSS CABLE to set the remote to control the satellite receiver Press POWER to turn off the receiver 11 Us
13. cleaner clearer images Make nn more smooth Turn on to keep Color and Tint in proper balance each time you change channels Picture Reset Reset the picture back to the Reset the picture back to the original settings original settings Turn fice omninenhel for manual adjustment of Color and Tint Bombard 17 Adjusting Your TV Sound Settings Stereo Expanded Stereo SAP and Tone Follow these steps to adjust the Stereo Expanded Stereo SAP or Tone of your TV SAP Second Audio Program is sometimes used to offer the program being watched in another language The chart below explains your options Press MENU PROG to select the Controls menu This menu is yellow 1 Select the Controls Menu Alarm Adjust Setup Press MOVE down to highlight the sound item you want to adjust 2 Highlight item to change Press MOVE gt or lt to adjust each item 3 Use MOVE P or lt to adjust each item Stereo Off Expanded Sound is automatically Sound is reproducedin Expanded stereo adds greater reproduced in stereo or mono width and dimension to stereo mono whichever the TV broadcasts creating a more station is broadcasting spacious stereo sound effect On Off Sound is reproduced in Sound is reproduced in another sound channel Stereo Expanded Stereo If nothing happens or Mono whichever is your broadcast may not selected in the Stereo have SAP Menu Item High Low High pitched s
14. dding all active channels into memory E Wait until the TV has cycled through all the channels and returns to the original channel 1 Place channels in memory AutoProgram Autopregramming A Press MENU PROG repeatedly to select the Setup menu This menu is white B Press MOVE down to highlight Channel Memory C Press MOVE P to underline the channel number 2 Add or delete channels D Select the channel number you want to add or delete with the number buttons _ E Press MOVE P to add or delete a channel you will see Stored on the screen when added and Erased when deleted F Repeat D and E for more channels 20 Using Advanced Features Naming the Channels You can name the channels using the character list below Full appears beside Label when the memory is used up Fixed appears beside Label for channel 00 it cannot be named A Press MENU PROG repeatedly to select the Setup menu This menu is white B Press MOVE down to highlight Label C Press MOVE P to underline the channel number D Select the channel number with the number buttons E Press MOVE P to underline the first character of the name 1 Name a channel NBC F Choose the character using MOVE A up or down eae G Repeat E F to complete the Controls Alarm Adjust Jims name H Press MOVE lt to move backward if you want to change an item 2 Erase a name A Follow A and B ab
15. echs naanin EEEE ERAEN 08 TATE sivesscsvaceeitnvisseadieveseseces 08 09 15 21 Toshiba scscssessscosvens 05 13 19 48 49 Totevision csesessceseseersrsseessececeee 07 09 TMK inanan ai 67 15501 ol a AE E A WAN a REL 07 Vector Research ccccscersene 14 16 44 VIGOR aan No 16 Video Concepts csssesssesenee 14 16 44 Videosonic secccsecscssescescsntccnnensecees 07 Wards incense 05 06 07 08 09 PETENTE EEN TEA 12 13 15 25 27 31 35 Yamaha aninha 02 14 16 30 46 Zen h oaaae 11 17 26 72 79 Using Your TV and Remote With VCRs Setting the VCR1 Channel The VCR 1 Channel works with VCR on the remote If the VCR 1 Channel is set pressing VCR selects the channel to see the VCR picture The VCR 1 Channel setting depends on which diagram you have used from the Connection Guide If you want to turn this feature off set the VCR 1 Channel to Disable Refer to the chart below for your setting A Press TV to set the remote to control the TV B Press MENU PROG to select the Setup menu This menu is white 1 Select the Setup Menu A Press MOVE down to highlight the VCR 1 Channel B Press gt to highlight the channel 2 Highlight VCR1 Channel Controls Alarm Adjust VCR Channe 03 A Enter channel 00 03 or 04 Choose your setting from the chart below Press CHANNEL down until Disabled is displayed to turn the feature off 3 Enter channel number VCR 1 Channel O
16. from the code list below C Release VCR2eLD D Press POWER If nothing happens try pressing VCR2eLD and then POWER A Tune TV to channel 00 03 or 04 B Point the remote at the laserdisc player and press VCR2eLD C Press POWER to turn it on D Use the buttons on the remote that relate to laserdisc player functions Not all buttons high lighted may work with your laserdisc player E Press POWER to turn it off Using Your TV and Remote With Audio Equipment Programming and Basic Operation Refer to the Connection Book or your Audio equipment owner s manual to hook up your audio equipment Your remote controls only RCA audio equipment such as a radio CD player tape player turntable or amplifier The remote may need to be programmed for your equipment This remote may not operate all models of brands listed below Use the codes below or on the sheet packed in with your remote Program the remote for A Point the remote at the audio POWER O OR equipment and hold AUDIO audio equipment B Enter the code from the a code list C Release AUDIO D Press POWER to turn it on If nothing happens try pressing gt AUDIO and then POWER a a E Repeat A D with another code CHAN if the first one does not work A Point the remote at the audio equipment and press AUDIO B Press POWER to turn it on C Use the buttons on the remote that relate to audio functions Not all buttons highlighted may
17. iiunvicniisieiendeieens 17 35 Autoprogram csecseeessessees 3 20 35 B Batteries Remote scesccceees 2 Braet steciescseeepantactcieras pestle 17 Biphtness sesiis 17 35 Buttons and ccccscoscrcscscessseeess 2 3 4 5 6 7 Audio Equipment s06 15 Component s e eccseseovoscsssesesscss 4 LaserdiSC onnies iaa 14 Meri e a 45 IN GIN DOE nananana Picture in Picture 4 7 24 25 35 POW C6 aaa aO 3 6 Remote Controll 006 4 6 7 TV Front Panel ceceeece 5 28 MOR E 10 Cable BOX 0nenee00sssssorenenessese 12 13 Cable Box Codes cccesssccsesees 12 CABLE DSS Button 6 12 13 Cable Chanmnel cc cccceseesesees 3 Cable or Air Feature 27 Cancelling Sleep Timer 22 Captioning Closed 00 26 COUUONS oa hile i Channel Label 0 00005 21 35 Channel Memory 3 20 35 Channel Name Display 29 Channel Number Display 29 CHANNEL Up Down Buttons Remote cnra 4 5 6 d ih AE AES E E ET T 28 Channels PAG GRIND annaa 20 Deleng cciias 20 Namie irice 21 Placing in Memory 3 20 Checks and Adjustments 30 31 Cleaner aea 33 CLEAR BUON sciis iieiea iasi 7 ClO kea Ga 3 23 Closed Captioning cccsccee 26 Codes AUGIO asia eii i 15 Cable BOX e sensesosesesoenescsssoss 12 Laserdisc Player sscsseeees 14 NR saeco tered crete 8 COT
18. ill get your TV connected and ready for watching For more details see the page numbers listed 1 Hook up your TV Use This Book First Hook up any antennas cables or Details are in the other equipment to your TV before i follow the steps below Connections Guide SONNET RONS you follow the steps below Plug the cord into the outlet matching the wide and the small end of the plug with the outlet 2 Plug in the TV 3 Put Batteries in the Remote ie A Pull off the cover of the battery compartment Sart B Place the four AAA batteries as shown matching the and SA d of each battery in th SS DDAA Ea R a C Replace the cover Startup 4 Turn on the TV 5 Place all available channels in memory AutoProgram Details for adding and deleting channels are on page 20 6 Set the Time Controls Alarm Adjust gam Ciock Quick Guide to Your TV En Ne Oy te G o Auftcoroaram Use O O K Q Q O HIV to set time Press TV on the remote OR Press POWER on the TV A Press MENU PROG until the Setup menu is selected This menu is white B Press MOVE to highlight Autoprogram C Press MOVE P to start placing channels in the TV s memory D Wait until TV has cycled through all the channels and returns to Original channel A Press MENU PROG until the Alarm menu is selected This menu is green B The Clock is automatical
19. ing Your TV and Remote With a Cable Box Programming and Basic Operation Refer to the Connection Book or contact your cable company to hook up your cable box If you have a cable box with its own remote then you may also be able to use the TV s remote with your cable box This remote may not operate all models of brands listed below Use the codes below or on the sheet packed in with your remote Program the remote for your cable box A Point the remote at the cable box and hold DSS CABLE B Enter the code numbers for your brand from the list below C Release DSS CABLE D Press POWER to turn it on If nothing happens try pressing DSSeCABLE and then POWER E Repeat A D with another code if the first one does not work Basic Operation Turn on the Cable Box A Tune TV to channel 02 03 04 05 or 06 the cable box channel B Point remote at the cable box and press DSS CABLE C Press POWER to turn it on D Press CHANNEL up or down to change channels on the cable box A Press DSS CABLE Turn off the Cable Box B Press POWER to turn it off Cable Box Codes Stargate 2000 Stargate 2001 nies a S AAE sua L0 11 59 17 21 49 50 55 General Instrument GIT400 eccceeees 04 05 15 23 24 25 30 36 i 03 12 13 34 48 28 29 32 33 40 41 VENEA L AONE anniier 44 14 42 57 61 26 28 29 32 33 40 41 Using Your TV and Remote With a Cable Box Setting the Cable Channel The Cable Channel work
20. isuse or neglect e Batteries e Images burnt onto the screen e A television that has been modified or incorporated into other products or is used for institutional or other commercial purposes e A television purchased or serviced outside the U S A e Acts of God such as but not limited to lightning damage Product Registration e Please complete and mail the Product Registration Card packed with your TV It will make it easier to contact you should it ever be necessary The return of the card is not required for warranty coverage How state law relates to this warranty This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your television outside the United States e This warranty does not apply Contact your dealer for warranty information References Order Form for Parts Remote 221113 This is the remote that came packed with your TV You can use the order form at the right to order it by mail Cleaner AHO35 To clean your TV cabinet we recommend Murphy s Oil Soap or Cleaner AH035 You should not use cleaners such as Windex with vinegar Lenox Furniture Polish spray or Heinz Cleaning Vinegar to clean your TV cabinet Using these cleaners will permanently mar the surface of the cabinet Such damage is not covered under your purchase warranty Detach Here 2 22 n nnn nnn nnn nnn ne nn nnn e
21. kground as shown at the left Menu Buttons These buttons are used with the TV s menus to adjust the features You can use the menu buttons on the remote or the front of the TV CoM CA 5 10 OF fr A BEV S2 r 3 MENU CHV CHAN VOL VOL 1 Press MENU PROG on the remote or MENU on the front panel to move from menu to menu a Moving through the Menus Engiish Francais Espa ve 2 Press MOVE a v on the oe 3 remote or CHANNEL up down on the front panel to move up and down through the features in the menu 3 Press MOVE lt and gt on the remote or VOLUME on the front panel to move left and right on the menu lines Using Your TV and Remote With Remote Buttons POWER Turns off the TV Turns off compatible VCRs power VERT DSSOCABLE py Turns on a component after a Q component button is pressed VCR2 LD AUDIO AUDIO VCR1 VCR2eLD DSS CABLE Sets the remote to control the STOP PAUSE programmed for one component DISPLAY CHAN SKIP See Using the Remote with a VCR equipment on pages 8 15 TV Turns on the TV Shows the displays on the screen Sets the remote to control the TV See Using the Remote with a VCR equipment on pages 8 15 REW Rewind Rewinds a tape or laserdisc Searches backward while tape or laserdisc is playing PLAY Plays tape or laserdisc FF Fast Forward Fast forwards a tape or laserdisc Searches forward while tape or laserdisc is playing
22. ly highlighted the first time you set it If it is not press MOVE V down to highlight it C Press MOVE lt to set the hour D Press MOVE P to set the minutes Quick Guide to Your TV Basic Tour of the Remote Basic information about your remote is shown below This will give youa general idea of how your remote works For more details see pages 6 15 pomir VON PESCARE Ty TV Power Button a D Turns the TV on Rew s Sets the remote to control the TV lt S gt gt DA i cy amp Volume and Channel Controls Operates TV when remote is set to Details are on page 6 amp o control the TV Operates the TV and advanced features 0000 600 Component Buttons Controls components such as a Details are on pages 8 15 VCR laserdisc player audio equipment and a cable box Menu Buttons Changes the menus and features See next page for details on the screen Picture in picture buttons Used to watch two pictures on the Details are on pages 7 and 24 25 TV at the same time Quick Guide to Your TV Menu Basics General information about using the on screen menu system is shown below Details on using the remote buttons are on pages 6 7 Many menu items are explained in detail in Using the Advanced Features starting on page 20 Yellow Green Light White Blue Press MENU PROG repeatedly to see each of the four menu colors Colors Each menu has a different color bac
23. mer is set to turn off the TV Details are on page 22 Picture in picture is turned on to channel 00 Details are on pages 24 25 Sound level of the TV No signal is coming in on video input channel 00 There is no sound See MUTE button on page 6 The sound is being broadcast in stereo Details are on page 18 SAP is selected in the menu but it is not available for the program being broadcast Details are on page 18 Secondary Audio Program SAP is selected and it is available for the program being broadcast Details are on page 18 The time remaining for commercial skip Details are on page 6 29 References Trouble Checks You may have problems that can be fixed with a few minor adjustments Look for the type of problem you are having below and then try the suggestions to get your TV going again For warranty information see page 32 Trouble Power TV will not turn on No picture no sound but TV has power Picture Blank screen or Unusable Signal appears on screen Picture poor sound okay Picture in Picture Can t get two different channels in picture in picture No picture while using ome picture in picture with S VHS VCR or camcorder 30 Checks and Adjustments Plug TV in Plug something else into the outlet to make sure it is working Make sure batteries in the remote are not dead Aim the remote at the TV and press TV Make sure batteries are placed in the remote the right way See batteries on
24. n page 5 YS the other two numbers REC STOP PAUSE INPUT PIP Picture in Picture Ce Le Lud Switches between the TV channels F mesman pee Snorer DISPLAY CHAN l E ANTENNA picture to the a Used as TV VCR button when O CS O remote is set to control the VCR SWAP Switches the channel in the small CLEAR picture with the big picture Clears menus and displays from l the screen FREEZE Clears items from VCR timer Freezes or unfreezes the programs and VCR s clock small picture MENU PROG Program EXPAND Shows menus on the screen and Switches between Stereo and moves from menu to menu Expanded Stereo Sets VCR clock and programs Press to switch between the two timer on VCR different options RESET Returns the picture adjustments to the original settings Using Your TV and Remote With VCRs Programming the Remote Refer to the Connection Book or the VCR s owners manual to hook up your VCRs The remote may need to be programmed for your VCR This remote may not operate all models of brands listed below Use the codes below or on the sheet packed in with your remote 1 Test the remote 2 Program the remote for your VCRs VCR Codes Admirals aa 06 79 PW aes aa n Aasia NEDAS Akai ciisctesiaccntachenes 03 17 22 23 63 66 Audio Dymamics scceseeeeeeees 14 16 Bell amp Howelll cccccsssscssessceceeeees 02 BroksonicC 233 lt hesce ventiseeriesteccetstelcctiees Candle cceee 07 09 13
25. nn en ne ne nen nnn ern rte eee nnn nn nen mnnenenes Order Form Book No 15336310 ___PartNumber Price Qty__ AH035 Remote CRK83B1 Total 10 Minimum Order Sales Tax We are required by law to collect the appropriate sales tax for each individual state county and locality to which the merchandise is being sent Shipping Handling and Insurance Total Amount Enclosed VISA or MasterCard preferred Money order or check must be in U S currency only No COD or CASH All specifications and descriptions of parts are subject to change without notice References USE YOUR CREDIT CARD Hef ete Copy complete account number YISA aaa ONUNU Card expires CL Copy complete account number JWeEGIOTe ike Copy Number above the name CITI on your MasterCard Card expires LLI L AUTHORIZED SIGNATURE Prices are subject to change without notice PLEASE Print or type your name and address This will be your mailing label A complete and correct order will save you days of waiting a page Rae a e ee a E aera ee E E a a eee 1 i Name l i Street J Apt j City l State Zip Make sure that both sides of this form have been filled out Detach Here e a ee OM ee SEEDERS REESE RATS SSS SSS SSSSTSSRS ST ST SSH STH SNS KH DOKKEN KK UT KKH NHN HR U S and Canadian Orders By Phone 1 800 338 0376 Call this toll free number between 8AM and 10PM Eas
26. nu Basics on page 3 MENU CH A and V VOL and Also VOL A and VOL v POWER and Not on all models Shows menus on screen Moves from menu to menu Channel up and down Scans up and down through channels in the TV s memory Moves up and down menus Volume up and down Raises and lowers sound Moves left and right on a menu line Changes a features setting Turns the TV on or off Same as VOL and buttons References Displays on the Screen Your TV shows the settings of several features on the screen To see what features have been set on your TV press DISPLAY on the remote Screen Display 12 00 AM KNBC 13 Video 00 S VID 00 Alarm Sleep PIP 00 Volume Unusable Signal Mute Stereo Stereo SAP ee 1 55 12 00 AM KNBC 13 or Video 00 S VID 00 Alarm Sleep PIP 00 Volume PENAT gt or Unusable Signal Mute Stereo 1 55 eee or Stereo SAP Description Time of the clock Details are on page 3 Name you chose to describe the channel Details are on page 21 Channel number you are watching Indicates that a component is connected to the VIDEO jack on the back of the TV it is turned on and channel 00 is selected Indicates that a component is connected to the S VIDEO jack on the back of the TV it is turned on and channel 00 is selected Alarm clock is set to turn on or off Details are on page 23 Sleep Ti
27. orkmanship For how long after your purchase e One year for labor charges One year for parts e Two years for the picture tubes The warranty period for rental units begins with the first rental or 45 days from date of enpment to the rental firm whichever comes first What we will do e Pay any Authorized ProScan Television Service Center the labor charges to repair your television e Pay any Authorized ProScan Television Service Center for the new or at our option refurbished replacement parts and picture tubes required to repair your television How you get service e For screen sizes of 20 and smaller Take your ProScan television to any Authorized ProScan Television Service Center and pick up when repairs are complete e For screen sizes larger than 20 Request home service from any Authorized ProScan Television Service Center e To identify your nearest Aurthorized ProScan Television Service Center ask your dealer look in the Yellow Pages or call 1 800 ProScan e Show the Authorized Service Center Representative your sales receipt or other evidence of purchase date or first rental What your warranty does not cover e Customer instruction Your Owner s Manual clearly describes how to install adjust and operate your television Any additional information should be obtained from your dealer e Installation and related adjustments e Signal reception problems not caused by your television e Damage from m
28. ory 000 3 20 Speak T S si sdcnsscsswssnosaessesissicstcatne 19 VCR 1 Channel cece ccs eseee 9 SNAP ESS ssscssccksscenssccssccshssscdassscsyes 17 a d a a F 1 OAREN OOREEN E A 35 SKIP orrea 6 35 Sleep Display c sssssseseeee 22 29 DICED LIMO R osisssa 22 SNATPN ESS sierici isna 17 E ee E a Te A E E ER 18 19 SOUTE hear o 35 Speakers cisnienie 19 ABCD essesi ias 2 3 SICTEO oiiae 18 35 Stereo Display ssesssssssereees 29 STOP Button nce kisi cckeddiesiiecce 7 SWAP Button cccccesees 4 7 24 25 Tablt of Contents cecccccccceees 1 Time PATO onn aa 23 COCK ooun E 3 Sleep TiMer essssososososssssessere 22 Time Display cssscsccesesesoees 29 PUN Casket a 17 TORC aeaa rei 18 35 Tour of the Remote sse 0 Trouble Checks c0cecese0s 30 31 Turn on Alarm cecccccsssnceeass 23 Turn on Picture in Picture 24 TUTE ON FV ecann a 2 TV Buttons esseeereossssesesssssssssssose 4 6 28 Guide to sesesosesesesesssesessosssso 2 3 4 TV Button ecciesia 3 4 6 A ee a 1 AEN E E AE AREEN Two Pictures at one time 24 25 bl gt l Unusable Si Display 29 35 Using EREE Features i 20 27 Naming the Channels 21 Place Channels in Memory 20 Setting Cable or Air 27 setting the Alarm Clock 23 setting the Sleep Timer 22 Watching Closed Captioning 26 Watching Two Pictures
29. ounds are Low pitched sounds are louder louder 18 Adjusting Your TV Sound Settings Speakers Follow the steps below to turn the speakers on or off in your TV The chart below explains your options Press MENU PROG repeatedly to select the Setup menu This menu is white 1 Select the Setup Menu Press MOVE down until 2 Highlight speakers ghlight sp Speakers is highlighted Controls Alarm Adjust Speakers OFF Press MOVE P or to turn the 3 Turn Speakers on or off speakers on or off Controls Alarm Adjust im Speakers Off The sound comes from the TV s No sound comes from the TV internal speakers 19 Using Advanced Features Placing Channels in Memory Autoprogramming Only channels 2 13 appear in the TV s memory when you first turn it on The channels available in your area must be programmed into the TV s memory when you hook up your TV Using CHANNEL up or down allows you to scan through these channels You may want to add or delete a few channels if some stations have weak signals or were off the air when the TV was programmed Refer to the Add or Delete Channels section below A Hook up an antenna cable or components before you begin these steps or you will not be able to add channels into memory B Press MENU PROG repeatedly to select the Setup Menu This menu is white C Press MOVE W down to high light Autoprogram D Press MOVE P to start the TV a
30. ove B Press MOVE P until clear is underlined C Press MOVE A up or down to clear the name Character List ABCDEFGHIJKLMNOPQRSTUVWXYZ amp 0123456789 lt gt blank space 21 Using Advanced Features Setting the Sleep Timer You can set your TV to turn itself off If you re watching TV at night and fall asleep the TV will turn off for you A Press MENU PROG to select the Controls menu and highlight Sleep Timer This menu is yellow B Press MOVE P to enter the amount of time you want to watch TV before it shuts off Each press equals 15 minutes C Press MOVE lt to subtract time from the sleep timer 1 Set Sleep Timer 2 Add more time A When 0 01 appears on the screen the TV will shut off in one minute Press MOVE P to add more time A Press MENU PROG to select the Controls menu and highlight Sleep Timer B Press MOVE lt until the time reaches 3 Cancel the Timer 22 Using Advanced Features Setting the Alarm Clock The TV can be set to turn on each day like your alarm clock You can set it to turn on to your favorite channel at a certain time You can also set it to turn itself off again The Alarm cannot be used until the clock is set 1 Turn on the Alarm A Press MENU PROG to select the Alarm menu and highlight Alarm This menu is green B Press MOVE P or 4 to select Alarm On On or Off 2 Set the Alarm Channel A Pre
31. program without sound If you have turned Closed Captioning on and it does not appear on the screen it is not available on the channel you are watching This TV does not support the text mode Text information typically consists of program information weather bulletins local activities etc Press MENU PROG to select the Controls menu This menu is yellow 1 Select the Controls Menu 2 Highlight Closed fe tee ee a ote Captioning Cosed Caan ng Ole Press MOVE down to high light Closed Captioning A Press MOVE 4 or P to select Off C1 or C2 Select C1 for full translation of the primary language in your area Select C2 for secondary language translation simplified English or whatever is being broadcast in your area 3 Select Setting Using Advanced Features Setting Your TV for Antenna or Cable Your TV automatically adjusts this feature when the TV places channels in memory autoprogram Follow the steps below to change the setting as needed Press MENU PROG repeatedly to select the Setup menu This menu is white 1 Select the Setup menu Press MOVE down to 2 Highlight Cable Air highlight Cable Air A Press MOVE lt or P to select Cable or Air Select Cable if you have cable Select Air if you have a home antenna con nected to your TV 3 Select Cable or Air Cabie Air ir 27 References Front Panel Buttons For details on using buttons with menus see Me
32. r connected to the video jacks Press CHANNEL up and down or two number buttons to change channels on the large picture Change channels on your VCR Laserdisc Player or Camcorder to change channels on the small picture Using Advanced Features Watching Picture in Picture Move the small picture Press MOVE PIP to move the small picture to the next corner Swap the big picture with Press SWAP to switch the small the little picture picture with the big picture A Press FREEZE to stop action in Freeze the small picture the small picture B Press FREEZE again to return to an action picture VERI DSSeCame Turn off Picture in Picture Press PIP to turn off picture in picture C2 21 Oo Ai 4 e z IO O Se a H o af a EoIO OO 25 26 Using Advanced Features Selecting a Language The on screen displays in this TV can be displayed in three languages English French and Spanish When you select a language most of the displays will be shown on the screen in your preferred language 1 Select the Setup menu Press MENU PROG repeatedly to select the Setup menu This menu is white Press MOVE lt or gt to select English Fran ais French or Espafiol Spanish 2 Select Language Watching Closed Captioning Closed captioning displays the audio portion of a program as words on the TV screen It is useful for the deaf hearing impaired or anyone who wants to watch a
33. rical Code Section 54 of the Canadian Electrical Code Part 1 which provides guidelines for proper grounding and in particular specifies that th cable ground shal be connected to the grounding system of the building as close t the point of cable entry as practical Table of Contents Important Information Quick Guide to Your TV Using Your TV and Remote Adjusting Your TV Using Advanced Features References Warning Startup 2 3 Hook up your TV Plug in the TV Put Batteries in the Remote Turn on the TV Place Channels into Memory Set the Time Basic Tour of the Remote 4 Basic Button Layout and Functions Menu Basics 5 Colors Menu Buttons Moving through the Menus With Remote Buttons 6 7 With VCRs 8 10 With a Satellite Receiver 11 With a Cable Box 12 13 With a Laserdisc Player 14 With Audio Equipment 15 Overall Picture 16 Picture Settings 17 Color Tint Brightness Sharpness Autocolor Picture Reset Sound Settings 18 19 Stereo Expanded Stereo SAP Tone Speakers Placing Channels in Memory Autoprogram 20 Naming the Channels 21 Setting the Sleep Timer 22 Setting the Alarm Clock 23 Watching Picture in Picture 24 25 Selecting a Language 26 Watching Closed Captioning 26 Setting Your TV for Antenna or Cable 27 Front Panel Buttons 28 Displays on the Screen 29 Trouble Checks 30 31 Limited Warranty 32 Order Form for Parts 33 34 Glossary __ 35 Index 36 37 Quick Guide to Your TV Startup The steps below w
34. s TV to set the remote to control the TV See buttons on page 6 7 Clear the path between the remote and TV of any objects Aim the remote at the component you are trying to control Press TV so remote will control TV Make sure batteries in the remote are not dead See if batteries are placed in remote correctly See batteries page 2 Press number buttons Channel may not be in memory See autoprogram on page 20 Make sure TV VCR switch on VCR is in the TV position For numbers over 100 press and hold 1 until 1 appears then press the other two numbers Set Cable Air feature to Cable for channels higher than 69 See page 27 Turn Stereo off The stereo broadcast may not be clear See page 18 Press VOLUME or MUTE to restore sound Make sure TV s speakers are on Details are on page 19 Try another channel Try adjusting the Tone See page 18 Change Stereo to off The stereo broadcast may not be clear See page 18 Make sure Stereo is turned on See page 18 Check Sleep Timer See sleep timer on page 22 Wait 30 seconds and turn on again a power surge may have occured Check Alarm Off time See alarm clock on page 23 Check Alarm On Time See alarm clock on page 23 Check clock time See clock on page 3 Make sure alarm is turned on or off See alarm clock on page 23 Check clock time See clock on page 3 31 32 References Limited Warranty What your warranty covers e Any defect in materials or w
35. s with DSSeCABLE on the remote If the Cable Channel is set pressing DSS CABLE selects the channel to see cable chan nels The Cable Channel setting depends on which channel your cable box must be on to see cable channels The channels usually used are 02 03 04 05 or 06 Consult your cable company for more information A Press TV to set the remote to control the TV B Press MENU PROG to select the Alarm Adiust Sm Setup menu This menu is white 1 Select the Setup menu Controls 2 nalish Francais Espa ol 2 Highlight Cable Channel A Press MOVE YW down to move down the menu until Cable Channel is highlighted Controls Alarm Adjust EEE B Press to underline the 3 Enter channel number A Enter the number for your cable box either 02 03 04 05 or 06 Press CHANNEL down until Disabled is displayed to turn this feature off lt 13 Using Your TV and Remote With a Laserdisc Player Programming and Basic Refer to your Laserdisc Player owner s manual to hook up your Laserdisc Player The remote may need to be programmed for your laserdisc player This remote may not operate all models of brands listed below Use the codes below or on the sheet packed in with your remote Program the remote for your Laserdisc Player Basic Operation 14 POWER VCRI DSSOCABLE yy VCR29 LD AUDIO A Point the remote at the laserdisc player and hold VCR2 LD B Enter the code for your brand
36. ss MOVE W down to highlight the Alarm Channel B Press MOVE P to highlight the channel number C Enter the channel that you want the TV to turn on to with the number buttons 3 Set On and Off Times A Press MOVE W down to highlight the On or Off Time B Press MOVE lt lt to set the hour C Press MOVE P to set the minutes D Press and hold MOVE lt to choose Disabled This turns the TV only on or only off at a certain time each day 23 Using Advanced Features Watching Picture in Picture Picture in Picture allows you to display a small picture within the big picture of the TV screen To watch two different programs at once you must connect a VCR Laserdisc Player or Camcorder You may need to disable the VCR1 Channel if you cannot get two different programs at once Turn on Picture in Picture Change channels on the large picture Change channels on the small picture 24 VCR Laserdisc Player or Camcorder Picture A Hook up a VCR Laserdisc Player or Camcorder to the video jacks on the back of the TV See the Connections Guide B Press TV to turn the TV on C Press CHANNEL up or down to select the channel you want to watch on the big picture D Turn on the VCR Laserdisc Player or Camcorder E Press PIP to put the small picture on the screen It is the same as the big picture F Press 00 to see the signal from the VCR Laserdisc Player or Camcorde
37. sssssseee 07 15 31 32 NEC orud 02 14 16 30 44 46 59 61 64 PanaSONic sssescecceeseee 08 53 75 77 Peri ta aiid auan An 05 35 44 Pentex Research ccccccsssccsessssesseees 46 PHIUCO nana 08 29 53 56 PMi pS oinei ae 08 29 PIONCET asiad 05 16 50 Porland sonsir eaa 44 45 52 g ese ee ee ene uonekana 00 Oar skits ide dunn nae 02 VILAS AP ua 08 53 RCA w snsssoseee 00 05 07 08 28 35 37 54 69 Radio Shack Realistic 02 06 08 A Press VCR1 or VCR2eLD to turn the VCR on B Press the VCR buttons shown at the left If your VCR does not work program VCR1 or VCR2e LD A Point the remote at the VCR and hold VCR1 or VCR2eLD B Enter the code for your brand from the code list below C Release VCR1 or VCR2eLD D Press POWER If nothing happens try pressing VCR button and then POWER E Repeat A D with another code if the first one does not work or if a second VCR is connected AEAEE E AS 09 12 15 19 27 43 53 OAMSUNG ioiissisissinsinsoesssas 07 13 22 32 42 SATIS UL vs osii adprenet 16 71 SATAY Os ATN EE 02 12 SCOl ENEE 04 13 41 49 68 Sears on 02 05 09 12 18 19 35 43 48 NAEP sissevteiasictssccsseeais 06 24 27 39 45 po 01111 0 1 17 26 31 55 SIENA esea ae aiaa 15 SON aea 17 26 38 Sylvania ciiisean 08 15 29 53 56 SYMP NONG inai 15 Taid cvcsuseesosssnciniseesvvonispehasasacauthosnpee 02 15 Tas PARI orriaren aa eaat eaii 09 Talint ane cheer acecstioneeneces 30 MOAC AE 15 30 69 T
38. tern Standard Time and place your order using your Visa or MasterCard Use this number only to place an order for accessory items listed on this order form By Mail Detach the information at the left and mail the payment to Thomson Consumer Electronics Inc at Video Accessories PO Box 8419 Ronks PA 17573 Most orders are shipped UPS within 72 hours If it is not possible to ship within 30 days we will notify you For more current information on these accessories write to the following address Video Accessories Customer Service Thomson Consumer Electronics Inc Distributor amp Special Products 2000 Clements Bridge Rd Deptford NJ 08096 2088 International Orders This offer is valid only in the U S Send your request for price quotation not orders to International Customer Service Thomson Consumer Electronics Inc Distributor amp Special Products 2000 Clements Bridge Rd Deptford NJ 08096 2088 USA References Glossary Antenna A device used to receive broadcast signals from TV stations Audio Sound reproduced by the TV Audio video cables Cables that carry sound and picture signals from one component to another Autocolor Adjusts the Color and Tint of the picture signals to the proper balance for all channels AutoProgram A procedure that automatically adds only the active channels in your area to the TV s memory Brightness Light and dark areas of a picture Channel Label
39. us Channel Button 6 Problem Solving csee 30 31 Product Registration ss00 i PROG Program Button 7 Programming the Remote Audio Equipment sss000 15 Cable BOX ssssssssrsassossscssessoseane 12 13 Laserdisc Player ssssssssseess 14 Satellite Receiver ccccsssseses 11 MER oeeo 8 9 10 Put Batteries in Remote Q Quick Guide to Your TV 2 3 4 5 R REC Record Button 00 7 11 Reference csscccccssssessecees 28 37 Glossary nissin insa 35 Order Form for Parts 33 34 Trouble Checks cccceee 30 31 Warranty ssasssinicisidisccecszssanscocesets 32 Remote Control Batteries nessseonenessassosossesesssse 2 BUON S aerninaaenan 6 7 Order Forim ccccccccssssssescoeees 33 TOUR eaa aasa 4 With Components 7 8 15 RESET Butttn cccscccscscccccssesccccees 7 REW Rewind Button 7 8 11 14 15 S Safety Information ccccssssseees i Satellite Receiver cccccccsssees 11 Screen DisplayS ssssesssceseees 29 DOPVICE esac ee 32 Set COCK eners 3 Sel Me auna 3 Setting Cable Air ssssssoees 27 Setting the Cable Channel 13 Setting the Sleep Timer 22 Setup Menu Autoprogram sesers 3 20 35 Cable Air cssccsiccccdactcatetavisasiciccs 27 Cable Channel 13 Channel Label 0000 21 Channel Mem
Download Pdf Manuals
Related Search