Inspire 1 The Inspire 1 is a professional aerial film making and
Contents
1. An integrated DJI Lightbridge based HD video downlink has been built in giving you a real time HD view of what your camera is seeing straight from your tablet This also allows you to activate Master and Slave modes so that one person can fly while the other controls the gimbal independently The controller s LiPo battery has a maximum run time of approximately four hours and can be charged by plugging directly into the controller remana O The Inspire 1 supports multiple remote controllers operating in master and slave mode This guide is based on using the master remote controller Refer to the Inspire 1 User Manual for more details on master and slave mode Fly Safe e P Mode Safe to fly In this mode the Inspire 1 has a strong GPS signal and can use Optical Flow positioning allowing it to hover accurately in position indoors and out If outdoors this mode also means that a Home Point has been locked so that it can Return to Home if the control signal is lost If you are not in this mode toggle the Flight Mode switch to P position to enable it The Optical Flow system works best at up to 2 5m above the ground It may not function properly when the Inspire 1 is flying over water over surfaces without clear patterns or over low light environments e Return to Home The Inspire 1 will return to home automatically if the remote control signal is lost or if a low battery level alert occurs It can also return to home w2. Do not fly in severe weather conditions This includes high wind snow rain and smog 2 Only fly in open areas High buildings and steel structures may affect the accuracy of the onboard compass 3 Avoid from obstacles crowds high voltage power lines trees or bodies of water 4 Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism including mobile phone base stations or radio transmission towers 5 Aircraft and battery performance is subject to environmental factors such as air density and temperature Be very careful when flying 3000 meters 9800 feet or more above sea level as battery and aircraft performance may be reduced 6 The Inspire 1 cannot operate within the polar latitudes 1 Download the DJI Pilot App Scan this QR code to download the DJI Pilot app Register your e mail address if using the app for the first time DJI Pilot App http m dji net djipilot 2 Watch the Tutorial Videos Watch the tutorial videos coming soon at www dji com or in the DJI Pilot app Scan QR code gt i R wa p Fi ka BER ARE For the best experience use mobile device with Android 4 1 2 or above iOS version on the way 3 Check Battery Levels Press the Power Button once on both the smart battery and remote controller to check battery levels Make sure both batteries are adequately charged before each flight Battery level low high 4 Charging On
3. Inspire 1 The Inspire 1 is a professional aerial film making and photography platform that is ready to fly right out of the box Featuring an onboard camera equipped with a 20mm lens and 3 axis stabilized gimbal it shoots sharp 12mp stills and stable video at up to 4K Its retractable landing gear pulls up out of view giving the camera an unobstructed 360 degree view of the world below An advanced flight controller makes the Inspire 1 stable safe and easy to fly indoors or out The brand new Optical Flow sensor gives it the power to hover in position at low altitudes even without GPS Like all DJI flight controllers it is also able to return home if remote controller signal is lost or if the low battery warning is triggered The Inspire 1 boasts a maximum flight speed 22m s and a maximum flight time of 18 minutes using one fully charged 4500mAh smart battery Please note that maximum run time the max transmission distance were tested in a lab environment These statistics are for reference only as conditions in your area may vary kma ylevand aas 12 avran sanus ington Retract E3 y R TRR E Remote Controller The maximum transmission distance of the Inspire remote controller is 2km As well as flight control the remote controller also allows you to control the landing gear or activate Return to Home with a tap Other buttons allow instant photo capture video recording picture review and gimbal control
4. ith a tap of the RTH button While returning home altitude will be kept level however the Inspire 1 is not able to avoid obstructions e Flight Limits The Inspire 1 is not permitted to fly within no fly zones as specified by local laws and regulations Please visit here http www dji com fly safe for more information Category A Safety Zone 1 The category A safety zone is comprised of a small no fly zone and a range of restricted altitude zones Flight is prevented in the no fly zone but can continue with height restrictions in the restricted altitude zone 2 1 5 miles 2 4 km around a designated safety zone is a no fly zone inside which takeoff is prevented 3 1 5 miles 2 4 km to 5 miles 8 km around restricted areas are altitude restricted with maximum altitude going from 35 feet 10 5 m at 1 5 miles 2 4 km to 400 feet 120 m at 5 miles 8 km 4 A warning zone has been set around the safety zone When you fly within 320 feet 100m of the safety zone a warning message will appear on the DJI Pilot app Category B Safety Zone 1 Category B safety zone is comprised of a no fly zone and a warning zone 2 0 6 miles 1 km around the safety zone is a designated no fly zone 3 A warning zone has been set around the safety zone When you fly within 0 6 miles 1Km of this zone a warning will appear on the DJI Pilot app e Environmental Considerations 1
5. ly use the official DJI Inspire 1 charger for your smart battery and remote controller To charge the Inspire 1 smart battery remove it from the body To charge the remote connect it to power through the port to a suitable power source 100 240V 50 60Hz Only connect batteries to be power when they have been switched off When battery indicators are all off on the smart battery it is fully charged If light on the remote controller is green it is fully charged Do not charge the smart battery and remote controller at the same time otherwise it may cause danger 5 Mounting the Gimbal and Camera 1 Remove Gimbal Cover 2 Align white mark on gimbal with white mark on the Gimbal Lock then insert gimbal 3 With gimbal in place turn the Gimbal Lock to the left facing the nose of the Inspire 1 until it locks into position 4 Remove the Gimbal Clamp from the camera after mounting 6 Preparing the Remote Controller Tilt the Mobile Device Holder to the desired position then adjust the antenna as shown 1 _ Press the button on the side of the Mobile Device Holder to release the clamp Zi 3 Connect your mobile device to the remote controller with a USB cable Plug one end of the cable into your mobile device and the other end into the USB port on the back of the remote controller Important 1 Ensure the antenna s position is perpendicular to the body of the remote controller for optimal transmis
6. n Pitch Pan 90 330 120 s 180 s to 30 TB47 22 2V 4500mAh LiPo 6S 99 9Wh 570g Operating Temperature Resolution FOV Field of View CMOS Lens Shooting Mode HD Recording Mode Supported File Format Support SD Card Types Remote Controller Operating Frequency Transmitting Distance outdoor unobstructed Receiver 1 PER EIRP and Working Current Voltage Battery capacity Optical Flow Sensor Frequency Velocity Range Altitude Range Operating Environment 0 C to 40C 1240M 94 1 2 3 F 2 8 20mm equivalent Anti distortion filter Single shoot Burst shoot BURST 3 5 7 frames per second AEB 3 5 frames per second 0 7EV Bias Time lapsed UHD 4096x2160p24 25 3840x2160p24 25 30 FHD 1920x1080p24 25 30 48 50 60 HD 1280x720p24 25 30 48 50 60 FAT32 exFAT Photo format JPEG DNG Video format MP4 MOV CMPEG 4 AVC H 264 SD SDHC SDXC Micro SD 5 725 GHz 5 850 GHz Remote Controller to Remote Controller 2 400GHz 2 483GHz Remote Controller to Aircraft 2km 93dBm 10dBm 900M 1 2A 7 4V 6000mAh LiPo 2S 13dBm 5 8G 20dBm 2 4G 50HZ Below 8m s 2m above ground 5cm 500cm Rich pattern surface with adequate lighting Lux gt 15 Operating Range 0 250cm
7. o avoid gimbal damage Place all propellers onto the correct motor and tighten by hand to ensure security before flight 8 Remote Controller Operation The remote controller is by default set to Mode 2 throttle controlled by the left hand stick Adjust the tilt angle of camera by using the gimbal dial Important You can set the remote controller to different modes using the DJI Pilot app REH Sema a A 9 Flight Taking Off 1 Goto the Camera screen of the DJI Pilot app Tap Q and confirm your selection The Inspire 1 will automatically take off and landing gear will automatically raise 2 Manual Take off a Start motors by pulling both control sticks to the bottom inside corners Release the sticks once the motors start b Slowly push the left throttle stick up to take off c Once in the air toggle the Transformation Switch up to raise the landing gear Ez LEB HL i ARE fo 448 EFIA R Landing 1 Auto Landing Go to the Camera screen of the DJI Pilot app Tap Q and confirm your selection The landing gear will lower and the aircraft will automatically return home and land 2 Manual Landing d Toggle the transformation switch to the lower position to lower landing gear e Gently pull the left throttle stick down to lower the aircraft until it touches the ground Pull both sticks to the bottom inside corners to stop the motors Power off the aircraft before powering off the
8. remote controller seiteg O Return to Home 1 Press and hold the return home button until the LED surround the button blinking white the return home procedure is in process Press once to stop the procedure EARME App En 2 If a low battery alert is triggered the Inspire 1 automatically enter RTH mode 3 Failsafe The Inspire 1 will enter RTH mode if remote controller signal is lost A 10 Using the Camera e Adjust the camera parameters using the Camera Settings Dial on the remote controller or through the DJI Pilot app Press the Shutter Button Video Record Button to capture photos or record videos e Adjust the tilt of the gimbal using the gimbal dial e Download photos and video from the SD card to your mobile device through the DJI Pilot app You may also use a SD card reader to export files to your PC Specification Aircraft Weight battery included Hovering Accuracy GPS mode Max Angular Velocity Max Tilt Angle Max Ascent Speed Max Descent Speed Max Speed Diagonal Distance Gimbal Operating Current Controllable Range Max Controllable Speed Battery Model Voltage Standard Capacity Energy Net Weight Charger Standard Output Power Camera 2935 g Vertical 0 5m Horizontal 2 5m Pitch 300 s Yaw 150 s 30 s 5m s 4m s 22m s 559mm Landing gear lowered 581mm Landing gear raised 750mA 900mA Station Motion a 01035 Pitch Pa
9. sion quality 2 Do not use other 2 4GHz devices at the same time to avoid signal interference 7 Preparing for Flight Place the aircraft on a flat surface in an open space with the back facing you 1 Move the Flight Mode switch to the right to select P mode P mode is Positioning mode A mode is ATTI mode and the F mode is function mode Refer to User Manual for details Make sure the Transformation Switch is in the bottom position Power on the Remote Controller Press the Power Button once then press again and hold for 2 seconds Repeat to power off Power on the Smart Battery Press the power button once then press again and hold for 2 seconds Repeat to power off Ensure the remote controller and your mobile device are connected with a USB cable Launch the DJI Pilot app and tap Camera Ensure the aircraft is functioning normally by completing the Checklist Calibrate Compass tap in the app and select Compass Calibration to calibrate the compass then follow on screen instructions Attach propellers with the black nut onto motors with the black dot and spin counter clockwise to secure Attach propellers with gray nut onto motors without a black dot and spin clockwise to secure IMPORTANT Return to Home is not available in non P modes The Inspire 1 will only maintain altitude not positioning and will drift with wind or after inputs Do not toggle the Transformation Switch before taking off t
Download Pdf Manuals
Related Search