3 in 1 E-light +rf+laser beauty equipment (Ex-900)
Contents
1. RF handle for RF treatment E light handle for E light treatment Laser handle for Laser Treat E LIGHT PART Getting started SS OS OS Gently squeezing the watering bottle it will help to watering faster Operation 1 Normal watering Screw off the little screw cap from overflow then Input water pure water or distilled water Connect the watering bottle and inlet well when there s water automatically spill from the overflow means the water is full of the water tank at this time you have to keep the outlet closed 1 1 Change the water inside of the machine every 10 15 days if you use the machine very often 1 2 When changing water just screw off the screw of outlet You d better put a water container under it 1 3 Our Apparatus is equipped with powerful cooling system after five minute s working you have to filling water again till there s water automatically spill from the spilt hole For this new machine if the probe is very hot in the beginning 10 seconds working please do not hesitate to close it right now Then shaking this treatment head 3 times over your head in this case the water of the head will flow back into water tank If the probe is still hot you can just repeat this action Please never power on the equipment if you do not fill water in it 2 Insert the relevant filter to the E light treatment handle then turn on the key switch After that please observe the water circulation inside the device Normally you will2. 21
3. automatic detection as follows ce KR ccc Se 1 Ea Picture 2 Treatment modes the selected mode will be Red stands Face Pulse radio frequency output as pulse way stands for Face continue continue to emit radio frequency usually the face continue operation with higher energy than face pulse ioo 1 cm To adjust the cooling levels of this machine The range is 0 10 Power of RF energy the range is 0 50J cm2 standby une it s state of standby functions refer to E light it s state of working functions refer to E light S back to last interface Steps 1 Clean the treatment area and Spread even cooling gel on the treatment area 3 5mm is the best 2 Stick the cathode patch on arms back or belly you should make sure it absolutely close to the skin of patients For body operation just stick on the opposite of treatment area Pay attention the cathode patch be more closer to treatment area the patients will get more intense feeling during operation 3 Testing choose face or inner arm skin for testing first make the treatment probe close to the treatment area then step on the foot switch move on the skin and ask the feelings of patients regularly and observe the skin s reaction to the treatment Usually they will feel a little cold of epidermis and very intense infiltration feelings of radio frequency and a little hot of dermis If no feeling you should increase the energy if the patients can t sta
4. hear the sound of water flow The probe runs cold in 1 2 minutes at this time you have to turn on 6 the E light RF controller switch at the front of this machine Picture 1 just press it it will light on then it s able to and start to treat 3 The upper screen will light on and show you as follows Picture 1 4 Touch Elight then you will come into the automatic detection as follows E LIGHT Select Treatment programs E Hair Removal gt Skin Rejuvenation Pigmentation Therapy gt Vascular Therapy Acne Therapy gt Wrinkles Therapy Picture 2 5 After detection Press anyone show you user mode interface Treatment program MM gt M Hair Removal ee C a E IPL energy peee Er 0 mm HE adjusting piuse 9 0 5 ru qe ay mmm 2 LA RF energy Pulse amount 0 adjusting RF working time MTS NMED pret KA repeat frequency Total comtor E 20 18 SHES e Cooling adjusting Status BPI St 37 back eE U E ean Picture 3 a Hair Removal current treatment program EM mmm 3 different groups of saved parameter setting Click ce system will enter into the saved parameters of mode 1 IPL d sw BA Ipp energy display Click ES and zd to increase or decrease IPL energy RF 0 vow MA RE energy adjusting E Rk cooling degree adjusting Pulsel working time of the first pulse 1 10ms adjustable Pulse 2 and Pulse 3 sub pulse
5. like needle pricking In one week after the treatment spots will be darker first Usually after one cycle treatment the perfect results will show you ffect of cooling gel cooling and light transporting e Usage spread the cooling gel on the treatment area before treatment about 3mm thickness 20 minutes after the treatment scrape the cooling gel and cooling with ice for 10 20 minutes f Operating sequence Clean skin and spread cooling gel on the treatment area after the treatment make an ice cooling treatment Theory and Treatment Applications Theory E light IPL RF Skin contact cooling system It s the new generation of beauty equipment it combines with the functions of optical energy and electromagnetic waves It adopts elective absorption of light which could get different impedance between target tissue and abnormal skin It could strengthen 12 absorption of electromagnetic of target tissue in the condition of lower light energy which could greatly reduce painless during treatment Treatment Applications 1 To remove unwanted thick or tiny hair 2 To make your skin tightening lifting skin improving flexibility and tone of skin 3 To rejuvenate your skin removing deep wrinkles pigments freckles vascular lesions telangiectasis whitening skin changing large hair pores 4 To remove Acne Improving the situation of oily skin Killing acne bacilli Technical Parameters Display Stand handle 480nm 1200n
6. reduce at once 5 To keep the powerful energy we suggest you change the water after 3000 shots 6 Please check the surface of treatment head if there s attachement object after treatment if so please lightly clean it with lens paper or absolute alcohol RF PART 14 Introduction How does it work When the RF energy get into the skin which could stimulate the water molecules of dermis to rub each other then make a lot of heat when the temperature reach at 68 72 degrees it will stimulate the dermis layer of collagen fibers immediately contract and stimulate collagen reconstruction and reborn of long term Show you younger and elastic skin What should I expect 1 Immediate result when the temperature of hypoderm arrive at 68 C 72 C the collagen will immediately shrink at this time the loose skin will lift and tighten at once The fine wrinkles will disappear the deep wrinkles will be lightened after one treatment 2 Long term effect To stimulate the recombination and regrowth of collagen In 2 6 months after one course treat return you a younger and flexible skin Technical Parameters RF output power 300W 1 50J cm adjustable 20mm for eyes amp face Getting started Probes and RF handle choose one probe and fit it in the handle Eyes Face Body 1 choose the right RF probe insert it to RF handle 1 Turn on the machine then come into Picture 1 Operation Picture 1 2 Touch B RF then you will come into the
7. remove acne blackhead c Feelings in the treatment Swollen feelings inside skin A little inflamed feelings on skin after the treatment d Effect of cooling gel cooling and light transporting e Usage spread the cooling gel on the treatment area before treatment about 3mm thickness 20 minutes after the treatment scrape the cooling gel and cooling with ice for 10 20 minutes f Operating sequence Clean skin and spread cooling gel on the treatment area after the treatment make an ice cooling treatment Acne Treatment 480nm First Pulse Increment Pulse Pulse Frequency IPL RF number delay Energy Energy so fet 8K a 1 2 course very serious skin problems it needs 2 course 3 weeks one treatment 4 6 treatments in all very significant effects show after 2 3 treatments b Pre operation deeply clean skin c Feelings in the treatment very Swollen feelings inside skin A little painful inflamed feelings on skin after the treatment d Effect of cooling gel cooling and light transporting e Usage spread the cooling gel on the treatment area before treatment about 3mm thickness 20 minutes after the treatment scrape the cooling gel and cooling with ice for 10 20 minutes f Operating sequence Clean skin and spread cooling gel on the treatment area after the treatment make an ice cooling treatment Vascular Therapy 530nm First Pulse Increment Pulse Pulse Frequency IPL RF Pere eee er acy Ey Ey rough amp
8. width 1 10ms adjustable Delayl 1st pulse delay interval between the 1 pulse and 2 pulse Delay 2 and Delay 3 interval between two pulses JUULI RF working time 50 2500ms adjustable Pulse amounts interval between two spots 1 4s adjustable amp back water circulating status lamp status Q ie charging status 280 counter of shots for the current treatment standby click standby the lamp will be lightened off Click standby when treatment finish to turn off the handle ready click ready the lamp of the handle will be lightened up and light will be simmered by press the button on the handle 640nm 690nm Hair Removal 530nm Pigmentation Therapy Spots Removal 560nm Skin Rejuvenation 580nm 590nm Vascular Therapy 480nm 430nm Acne Treatment Pay attention the filters above are optional Hair Removal 640nm First Pulse Increment Pulse Pulse Frequency IPL RF number delay Energy Energy s Je b b b hb kR blacker amp thicker hair smaller first pulse longer pulse delay 40 doe js a tft light colored amp thin hair longer first pulse shorter pulse delay Hair Removal a one course in all every months as one treatment 4 6 treatments in all Usually very significant effect will show you after 2 3 treatments For thick hairs it needs 3 treatments For soft and thin hair it needs 5 treatments Treatment time For two arms in 1 5 hours For two legs in 1 5 hours For armpit hair
9. 3 in 1 E light rf laser beauty equipment Ex 900 USER S MANUAL Please read this manual carefully before operating this machine Retain it for future reference i ffl j ill A a _ te SE F mat 1 Before open the machine you must fill the water to this machine until the water automatically come out of overflow means the water is full of water tank or it will easily make it broken 2 Keep any reflecting things out of the operating room such as mirror watch jewellery 3 Any intense pulsed light or laser without correct using can injure the body In the course of working the device will produce high pressure So every operator should keep warning operating according to this introduction 4 Patient Well trained operator and appropriate disposal treatment room is very necessary and important Moreover the patient should also know the treatment theory and wear the professional protective goggle protecting eyes from burning except for the RF treatment 5 Operator Durng the treatment except for the RF treatment it s possible to touch the intense pulsed light or laser so it s necessary to wear the professional protective glasses 6 Treatment room the room must clear mark using intense pulsed light amp Laser 7 Except the authorized mechanic anyone have no right to examine and repair the machine especially the inside of device that including electrical source cooling system optical organs and treatm
10. AA Frequency 3 Hz J CM re 600 Ka Oo ri Start To switch the work status press down this button Pause To stop the work status press down this button EN increase Energy 1 1500J or Frequence 1 5Hz a To Decrease energy 1 1500J or Frequence 1 5Hz e Pre operation Clean skin e Operation Steps 1 Filling water 2 Choose Treatment head 1064nm 532nmThen fix it in the laser gun 3 Turn on the key switch and the laser control switch Adjust the parameters Point the Start laser output to the treatment area then Press down the key and step on the laser foot switch now the statue become to work start to emit laser At this time you will find the display screen start to count ay attention During the treatment Patients should be coordinated with operator do not move do not open eyes or it will damage the eyes The distance between pr obes and treatment area is about four fingers about 12cm the laser handle should be perpendicular to treatment area Show as following picture 25 1064nm 532mm 4 After finishing the operation you have to release foot switch first secondly press down ER key back BEN en the machine cooling down then turn off the key switch and laser control switch Pay attention During the operation tell the patients do not move do not never open eyes Skin care after treatment e Uncomfortable Symptons in 3 5 days after treatment 1 The face will be
11. bigger vascular longer first pulse Frough bigger vascular tonger frst puse smaller vascular smaller first pulse smaller vascularsmallerfretpulse SS fred face big gr frstpuse O O red face bigger first pulse ascular Therap a 4 6 treatments as one course 3 weeks apart one or two course in all Very obvious effects will show you after 2 3 treatments b Feelings in the treatment Swollen feelings inside skin A little inflamed feelings on skin after the treatment c Effect of cooling gel cooling and light transporting d Usage spread the cooling gel on the treatment area before treatment about 3mm thickness 20 minutes after the treatment scrape the cooling gel and cooling with ice for 10 20 minutes e Operating sequence Clean skin and spread cooling gel on the treatment area after the treatment make an ice cooling treatment Pigmentation Therapy 530nm First Pulse Increment Pulse Pulse Frequency IPL RF number delay Energy Energy 11 so pe p p p EGER 3 fos 3 3 ao 0 3 3 5 4 whiter skin higher energy shorter pulse delay Pigmentation Therapy 3 darker spots good skin a 1 2 course 2 course is for very serious skin problems like serious chloasma 3 4 weeks one treatment 4 6 treatments in all b Treatment symptoms the freckles become darker after one treatment the treatment area will be red the freckles will gradually be light and drop off c Feelings in the treatment some pain feelings
12. ctions but never beyond their tolerance Attentions Some slack parts like cheeks and back of ear lobe should be lifting with much more force and repeat some times Do let the probes close to treatment area and every movement must end on hairline Nasolabial sulcus Nasolabial sulcus is also one part which easily show one s aging So it s necessary to repeat operation on this area Start from corners of the mouth lifting up move along nose groove wrinkles then stretch to temple end on hair line 20 Forehead 1 When treatment eyes should decrease the energy start from 1 then increase it according to customers tolerance 2 Picture 1 Start from underside of eyes to upperof temple make it to be a curve could repeat some times especially on crow s feet 3 Picture 2 After that start from brow lifting to temple Must keep away from the eyeball repeat this movement 4 Picture 3 Start from brow lifting up Keep this movement end on hair line Pay attention do not use very big force on this area decrease the energy start from 1 21 Neck t Start from middle of forehead to both sides of hair line move along the wrinkle directions 2 Liftup to hairline again it will help to decrease the wrinkles around this area Pay attention YVery less fat on forehead you d better start from 1 lf the wrinkles are very deep you should repeat movements 22 If operator is not very skilled to operation on face do not
13. d better use the pure biological skin care products not chemical products and the silty cosmetics If there s flare on treatment area a doctor should be notified immediately and stop make up Take some VitC or VitE 4 Treatment course 6 8 times as one course 2 3 course in all The next treatment should be carried out after 3 weeks After one course treatment the problems such as age spots spots ect will be solved the skin becomes shiny and flexible 5 As physical differences in personal individual customers may be temporary discomfort small blisters pigmentations flare in this case we suggest you use ice pack for 30 minutes you can make up 5 days later after treatment Maintenance 1 No stress on the Screen prevent from breaking up 2 Keep the filters and probe clean do not let the cooling gel enter into probe We suggest you slightly clean the filters wafer after each treatment with soft and clean paper towel if it s very dirty on its wafer please Dip the paper towel in a little dehydrated alcohol then clean it just as follows lt a AOS Ul Hit reall eh DAL it 1 2 3 The handle is fragile please take care when pick up and dropt it in the bracket 4 Every 15 days to change the water After changing water please make sure water circulate normally before usage If the probe continuing be in high temperature after continuing working too long you could change half of water from the machine In this case the temperature will
14. ent handle Notice the dangerous high pressure inside 8 Make sure whether it s accordant to your resident voltage or not 9 Maintenance must after turning off the device Or it s most possible to injure people and damage the equipment 10 Keep the probes of E light IPL handle RF probes clean To clean then with water or soft paper towels Do not let the cooling gel enter into the probes 11 Stop turning on when finding slack from treatment head If turning on close right now 12 Over light energy could burn skin that results in atrophy or pigment deposit 13 Do not directly see the intensed pulsed light or laser during treatment even wearing the protective glasses or goggle 14 Do not allow to point the treatment handpiece to the air Generally hang it in the bracket of the machine 15 When maintaining please close power cover board and observe in person 16 Total weight is a little heavy so please take care when moving 17 The temperature will raise after absorbing light energy so please take actions to reduce the flammable risk on treatment parts or around area Such as cold jel or ice cooling 18 Do not use ethanol acetone or other flammable things on skin before treatment lf necessary please use soap or water 19 When listerizing the treatment handle or other parts in ethanol please wait till dry E LIGHT LASER Treatment 1 People who are allergic to light 2 Pregnant women Diabetes suffers cardiac patients people with Hypertens
15. ion Epilepsy and skin cancer 3 People with cardiac pacemaker and defibrillator 4 People whose treatment parts are damaged 5 People are just back from the beach The skin is very weak after the exposure in the sun in this time 6 People have taken some photosensitive food or drug recently RF Treatment 1 Pregnant women 2 People with Hypertension diabetes heart disease very sensitive to electricity gestation period Hematologic disease 3 People with Cardiac Pacemaker severe skin disease Hypodermal injection 4 People with Collagen Botox injection should wait 3 months first 5 People with skin operation such as skin lifting operation should be very careful when treatment 1 6 People with nose reshaping or laser near sighted operation should keep off these parts Important Information This user s guide contains important information on the use and operation of this machine Please read all the information carefully for optimal performance and to prevent any damage to or misuse of the machine Any changes or modifications not expressly approved in this user s guide could void your warranty for this equipment E light IPL handle 1 Protective glasses 1 Goggle 1 oe 4B RF handle 1 E gt PFE RF probes 3 Pedal 2 Laser probes 2 Keys 2 Watering bottle 1 E gt Watering pipe Part of the machine E light RF display screen Laser handle E light handle RF handle ss Picture 1
16. m for acne 8 inch touch display 10 40mm with 3 filters 530nm 1200nm for red face red nose spider veins skin rejuvenation age spots sun spots pigmentation troubles 640nm 1200nm for hair removal 430nm 560nm 580nm 690nm for your choices Energy 1 50J cm2 IPL 1 50J cm2 RF Pulse width 0 1 30ms Pulse number 1 5 adjustable 1 99 ms adjustable Shot period Frequency 1 5 second adjustable 40 000shots Wind water semiconductor 1000W AC 110V 220V 60HZ 50Hz Parts to buy Protective glasses and goggle extra lamp for E light Pulse delay Lamp longevity Cooling system Power Voltage Features 1 E light owns all advantages of traditional IPL treatment No risk of burning and uncomfortable feeling cause by IPL treatment Good result for blond hair and light colored soft hair 2 Modular Design of inner structure easy to repair 3 8 4 TFT colorful touch screen 4 Pedal supplied to meet your personal operation habits Warnings after treatment 1 Pay attentioniln one month after treatment the patient should use sunscreen SPF15 when going out you d better take an umbrella and wearing a hat in case of sunburn If your skin expose in the sun it will increase the regeneration rate of 13 melanoma directly result in excessive pigmentation 2 You should often use moisture mask to supply water to your skin Keep your skin retain water You d better use a mask before treatment 3 Do not make up immediately after treatment You
17. nd the temperature you should decrease the power moderately or make sure if the probe has definitely close to the skin Operation tips 1 The probes must close to the treatment area no aperture 2 For operation you must put the probe close to the skin firstly then step on the foot switch After finishing the operation you should release the foot switch firstly then move away the treatment handle or it will easily scald the skin 3 When operation you must make the efforts be uniform each movement must finish to hair line 4 When operation on sensitive area like Mouth nasolabial fold forehead the patients will 17 feel very intensive feelings and the mouth cavity will be very hot it s very normal cause the radio frequency owns very strong infiltration power and just in this case it will get the best results 5 When operation on the neck the operator must be very careful there s a lot of lymph node and nerve and not very flat So you should tell the operator lie flat and move away the neck pillow If you are not very familiar to the operation please never operate the neck 6 If the cooling is too strong you should close the cooling switch on the rear of the machine for a while 7 Just rememeber that the operation should towards the direction of reducing and smoothing the wrinkles make sure there s a cross point every step 8 To get the best treatment results you should make a moisturizing mask for patients before operation the patients should
18. never operate on this part Lifting the unwanted fat of neck and skin to hair line of upper temple There s a lot of lymph and nerve so the energy should be lower start from 1 1 Move around the navel make it to be a circle Relax skin 2 Move on side of belly as a8 3 Move the fat of waist to underside of belly and inguen Move unwanted fat of belly to breast Skin care after treatment 1 Use some sunscreen lotion in case of sunburn 23 2 Pay attention to moisturizing skin very often 3 Do not make a lot of face expression in 3 hours after treatment 4 Do not never go to hot place like Sauna spa Maintenance Same as E light LASER PART Introduction e Treatment Theory Eliminate spots remove tattoos The specific laser wavelength will effect on and melanin of epidermis and dermis The pigments will begin to swell and explode to tiny particles after absorbed this high energy laser One part of them will be shot out of the body the other parts will be gradually removed by metabolism e Application To wipe out tattoos to eliminate eyebrow cleaning eyeline cleaning age spots birthmark ect e Technical Parameters Laser type Q switched ND YAG laser Laser wavelength 532mn 1064mn Cooling system Wind cooling Water cooling Semicondutor Light source 220V 110V 50Hz 60Hz e Features Moderate treatment no risk of scars and wound It s the most moderate laser treat No side effect no recovery time back to work at once
19. often make moisturizing mask after treatment Operation Steps Face The first step Stretch 1 Move along the chin to the ear lobe keep the movement be in acurve 2 Move along the corners of the mouth to the middle of the ears Keep the movement be in a curve 3 Move along the nose groove to upper nose keep the movementbe in a curve 4 Move along the middle of nose groove to hair line Keep the Movement be in a curve Attentions 1 Every movement line must end to hairline you should adjust the energy according to customers tolerance 2 Before operation test on the sensitive part below the ear lobe the energy start from 1 then add the energy 1 by 1 till it s beyond their tolerance 3 For sensitive skin you should choose some lower energy please start from 1 When they are used to the machine you could increase the energy in the following treatments The second step Lifting The four step Beautify Move along the side of neck to the eyes below The very slack parts like side of ears cheeks should lift with more much force and finish on the hair line After step 1 move from middle of nose groove to upper of temple make the movement as a curve in this casethe skin will be definitely stretched Repeat the first step Attentions Every movement must end to hair line Energy adjusting according to customers tolerance At this time customers have some adaptabilityso the operator could add some energy bigger energy better fun
20. redness or become swollen which is a role of heat that will promote collagen regrowth Pay attention do not never make ice cooling at this time just wait for 20 60 minutes they will be gradually disappeared 2 The skin is very dry so you have to pay more attention to keep moisture of skin 3 somepeople will have a little allergic to carbon powder you can rub some external medicine e Cosmetic and skin care products 1 Do not clean face with too hot water and irritant clean products 2 Choose some moisture lotion and sun protection lotion for skin care 3 Use some moisture essence such as Hyaluronic Acid B5 for skin repair e Daily Life 1 Do to go to High temperature places in 3 5 days after treatment such as sauna Hot spring sunbathing 2 Do not smoke drinking stay up all night 3 Pay more attention when make up remover Maintenance of machine 1 Keep the treatment head clean with cotton bud 2 Change the water after 10 15 days 3 lf there s no laser emit from the treatment head to check if the system come into Ready or check if the foot switch connect well or not 4 lf the emit laser become very weak or no laser to check if the treatment head clean or 26 not or the water circulation is good or not 5 If do not enter into Ready to check if cooling water enough or water circulation is good or not 6 If do not open the machine to check if the power line connect well fuse is good or not emergency switch is open or not
21. s in 30 minutes b Every month as one treatment Because the hair has its own growth period and dormant period so it s effective to remove the hair in growth period one month is the growth cycle of hair c Feelings in the treatment some pain feelings like needle pricking 3 8 hours after the treatment a little inflamed feelings on skin Gentlely tweezer or use your fingers the hair root naturally sheded and no pain which means the best effect In this case after 7 days the hair will loss automatically d Effect of cooling gel cooling and light transporting e Usage spread the cooling gel on the treatment area before treatment about 3mm thickness 20 minutes after the treatment scrape the cooling gel or cooling with ice for 10 20 minutes f Operating sequence shave away unwanted hair or shear the unwanted hair 1 2mm to the hair root first then Clean skin and spread cooling gel on the treatment area after the treatment make an ice cooling treatment Skin Rejuvenation 530nm First Pulse Increment Pulse Pulse Frequency IPL RF freemen moar eo ery Ey darker skin smaller energy long pulse delay whiter skin higher energy short pulse delay 0 3 eye pouch wrinkles course pores Skin Rejuvenation a one course in all every 3 weeks one treatment 4 6 treatments in all Usually very significant effect will show you after 2 3 treatments For face treatment it needs about 30 minutes b Pre operation deeply skin cleaning
Download Pdf Manuals
Related Search