s h owe r sp a - Quality Craft
Contents
1. multi function hand held Installation Guide and User Manual CIC 199 5221 2 Model 81 P00 000 SANOH LV AONAIYSAdXSA VdS AHL LAD eds JIOMOUS Please read and save this guide before using your shower spa Store the guide in a safe place for future reference IMPORTANT If you have any problems with this unit or there are missing or damaged parts please call toll free 1 800 459 4409 8 30 am to 5 00 pm EST DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE before calling the toll free number above 1 Carefully check the unit prior to installation to ensure there is no damage Installing a damaged unit will void the warranty Do not dispose of any packaging until you are satisfied with this product Your installation must comply with all local plumbing building codes Have a qualified tradesman do or approve your plumbing installation Protect the entire surface during installation Always wear safety goggles and gloves in order to avoid personal injury a SS iS TOOLS REQUIRED Adjustable wrench Carpenter s square Tape measure Pencil Teflon tape Electric drill Drill bit 7 mm or 4 Phillips screwdriver DANGER Do not place electrical appliances close to the shower enclosure CONTENTS ot SS i Wall anchors Wall bracket Screws Stainless steel washers Small hook 6 Non slip ring 7 Nut 8 Shower column 9 Regulator 10 Hand shower 11 Check valve 12 3 way valve 13 Rubber was2. following receipt of claim in which to inspect the product We assume no responsibility for labor costs or removing replacing a previously installed product or transportation or return of a product Imported by QualityCraft Laval Qu bec Canada H C 0A5 1 800 459 4409 www qualitycraft com Made in China
3. her 14 Short hose 15 Long hose INSTALLATION This unit is designed to be installed using your existing plumbing Your shower valve diverter valve or diverter tub spout will be used in its current position and will operate as it was used before with your current shower head The current shower arm and decorative ring will be removed and used for this shower panel existing existing _ a shower valve l shower valve E tub spout _ lverter diverter Sa Screw off your existing shower head from the shower arm as shown in Fig A Take out the decorative ring from the shower arm as shown in Fig B Screw out the shower arm from the wall as shown in Fig C The shower arm and decorative ring will be used to connect the water outlet and the shower panel in the following steps Lake SESE EEE mL IF ETF IP F777 Pit PITTI LI 77 a a a NEE 2 Mark the drill holes 7 mm as shown in Fig D The three holes consist of two holes drilled side by side 17 mm apart from the center of each hole with the centerline running between them The third hole is drilled on the centerline 20 mm below the first two holes The upper two holes should be drilled below the water outlet in the wall 170 mm down vertically from the center of the existing water outlet The two group holes are 480 mm in vertical distance from each other Insert wall anchors 1 i
4. ier installer user or other person or resulting from without limitation any of the following careless handling lifting unit by plumbing abrading finish etc modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage Supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition Quality Craft WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use etc including its own negligence damages to respecting or resulting from plated parts when chemicals are used in or on the unit optional equipment not manufactured by Quality Craft or defects that should have been discovered before installation This limited warranty does not include labor transportation or other costs incurred in the removal and or reinstallation of the original unit and or installation of a replacement unit any costs relating to obtaining access for repair or loss of use damage including l
5. nto the pre drilled holes Secure the wall brackets 2 to the wall with the screws 3 and stainless steel washers 4 Fig E OO FIG D FIG E 17 mm J mm 7mm g A fe J o d em G O a a a e 170 mm 480 mm e mm Hs AN 4 Secure the small hook 5 to the side of the shower column 8 using non slip ring 9 Place the rubber washers 13 into each nut on the short hose 14 Secure one nut to 6 and nut 7 Fig F the 3 way valve 12 and the other to the water inlet on the shower column 8 Fig K 5 Hang the shower column 8 on the wall brackets 2 as shown in Fig G Make sure 10 Place the rubber washers 13 into each nut of the long hose 15 secure the the top inlet hole of the shower column aligns with the water outlet on the wall hexagon nut to the 3 way valve 12 and the knurled nut to the hand shower 10 Fe eE The check valve 11 has been pre installed into the hand shower Fig L FIG K FIG L 6 Wrap some Teflon tape around the original wall install end of the shower arm as mentioned in step 1 Make sure it is the same end that was installed into the wall IMPORTANT NOTES if installed in reverse direction there will be NO WATER FLOW Secure the shower oo A Shower arm and adoring ring are not supplied Use the current one from your arm to the water outlet in the wall Fig H original shower installation B The regulator 9 and the check valve 11 have been pre ins
6. oss of sales profit or business advantage of any kind under any circumstances It is the responsibility of the installer owner to determine specific local code compliance prior to installation of the product Quality Craft makes no representation or warranty regarding and will not be responsible for any code compliance Quality Craft does not warrant connections of water supply fittings and piping or fill systems Nor is it responsible for damage to the shower panel which occurs during any installation procedure lf you have a problem with your unit before installation please return it to the place of purchase If you have a problem with your unit during or after installation please call Quality Craft Customer Service at 1 800 459 4409 8 30 am to 5 00 pm EST or through our website at www qualitycraft com WARRANTY CLAIM PROCEDURE lf a claimable defect occurs please fill out a claim form through our website at www qualitycraft com or contact our customer service department at 1 800 459 4409 8 30 am to 5 00 pm EST Before you make your claim call please make sure you have 1 The description of the shower spa 2 Proof of sale 3 Details regarding the defect 4 Name and address of the owner and installer Claims must be filled out in writing and returned within six 6 months of appearance of defect Failure to comply with this stipulation will make the warranty null and void We reserve the right to a thirty day 30 delay
7. shower arm 4 If there is no water flow check that the hoses are not bent or kinked after final installation Check the water connections for proper flow CARE AND MAINTENANCE e After use rinse the shower column with water using the hand shower to remove any soap deposits e Never use abrasive cleaners as they will scratch the finish REPLACEMENT PARTS If you are missing or require replacement parts please call customer service at 1 800 459 4409 Monday Friday 8 30 am 5 00 pm EST or email us at custsupport qualitycraft ca Identify the required part s and have the replacement part number ready when you call CODE DESCRIPTION QTY QCGPH2A01 Screws 6 mee Stainless steel washers 6 Wall anchors 6 Mounting brackets 2 QCGPH2A02 Rubber washers 4 QCGPH2A03 7 with skid proof washer l Eo and nu QCGPH2A04 3 Way valve l QCGPH2A05 Long shower hose l QCGPH2A06 Short shower hose l QCGPH2A07 Hand shower head l 1 YEAR HOME USE WARRANTY This unit is warranted to the original purchaser to be free of defects in material and workmanship for one 1 year from the date of purchase This warranty does not extend to commercial or institutional use or installation Quality Craft will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions WARRANTY LIMITATIONS Our warranty does not cover defects damage or failure caused by the common carr
8. talled There is no need to install them 7 Attach the decorative ring to the shower arm to cover the joint area Fig I 8 A regulator 9 is pre installed into the 3 way valve 12 screw the end of the 3 way valve 12 tightly to the shower arm Fig J FIG H FIG FIG J OPERATION To use the shower panel open your shower valve as per your normal use flip the diverter valve on the shower valve or on the tub spout to redirect water from the toe tester or tub s spout to the shower Use the selector switch as shown to the right to choose between the three below options A Hand shower and body Selector jets combined B Body jets Switch C Hand shower Choose option A by rotating the selector counter clockwise toward the top until you hear a click The water flow may be lower than the single body jets or hand shower Choose option B by rotating the selector in either direction in the middle range until you hear a click Choose option C by rotating the selector clockwise toward the bottom until you hear a click Adjust water temperature and pressure using your existing shower valve TROUBLESHOOTING 1 Ensure rubber washers 13 are installed properly to avoid leaks 2 Make sure you drill holes according to the instructions and secure the panel on the wall brackets 2 3 If you find that water pressure or volume is low clean the mesh gaskets in your existing
Download Pdf Manuals
Related Search