Home

DAP-1150_User Manual_v.1.3.0_29.12.11_EN - D-Link

1. Page 86 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed change the settings of the VPN tunnel available in the Miscellaneous section Internet connection wizard Miscellaneous Additional settings of VPN tunnel Enable RIP E NAT 7 firewall Y lt Back Next gt Figure 79 Configuring PPTP Static IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox if you want one WAN IP address to be used for NAT all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Click the Next button to continue After that the page displaying all specified settings opens Click the Save button to create the connection or the Back button to specify other settings After clicking the Save button the quick settings page opens Page 87 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual PPTP Dynamic IP or L2TP Dynamic IP Connection Internet connection wizard Connection name The connection name has been generated automatically according to the specified parameters You can specify another name or skip to the next step Name dynpptp_WAN_2 lt Back Next gt Figure 80 Configuring PPTP Dynamic IP WAN connection In the Name f
2. DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual WPS On the Wi Fi WPS page you can enable the function for secure configuration of the WLAN and select a method used to easily add wireless devices to the WLAN The WPS function helps to configure the protected wireless network automatically Devices connecting to the wireless network via the WPS function must support the WPS function If the device s WLAN is splitted into parts the value 2 3 or 4 is selected from the MBSSID drop down list on the Wi Fi Common settings page the WPS function can be used only for the first part of the WLAN the first value from the BSSID drop down list Before using the WPS function it is required to configure a type of WPA encryption D Li i l 4 System X Language X DAP 1150 Wi Fi Advanced Firewall System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Enable Disable WPS WPS Enable 2 Change Information Default PIN code WPS Status Configured SSID DAP 1150 Network Authentication WPA2 PSK Encryption TKIP Encryption key 76543210 Refresh Reset to unconfigured Connection WPS Method PEC Connect Figure 46 The page for configuring the WPS function Page 51 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ae a Configuring Device Access Point Mode User Man
3. Port 514 Figure 57 The System System log page The Configuration tab To enable logging of the system events select the Logging checkbox on the Configuration tab Then specify the needed parameters Control Description Select a type of logging from the drop down list e Local the system log is stored in the device s memory and displayed on the Log tab When this value is selected the Server address type Server and Port fields are not displayed Logging type Remote the system log is sent to the remote host specified in the Server field Local and remote the system log is stored in the device s memory and displayed on the Log tab and sent to the remote host specified in the Server field Logging level Select a type of messages and alerts notifications to be logged From the drop down list select the IP value to specify an IP address Server address type of a host from the local or global network or the URL value to specify a URL address of a remote server The IP or URL address of the host from the local or global network Server l to which the system log will be sent A port of the host specified in the Server field By default the Port value 514 is specified Page 67 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Access Point Mode After specifying the needed parameters click the Change button To disable logging of the sy
4. the key is not renewed Page 35 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual When the WPA WPA2 or WPA WPA2 mixed value is selected the RADIUS settings and WPA Encryption settings sections are available Security settings Network Authentication WPA2 WPA2 Pre authentication E RADIUS settings IP address 192 168 0 254 Port 1812 RADIUS encryption key dlink WPA Encryption settings WPA Encryption AES WPA reneval 3600 Figure 30 The WPA2 value is selected from the Network Authentication drop down list Parameter Description WPA2 Pre The checkbox activating preliminary authentication displayed only authentication for the WPA2 and WPA WPA2 mixed authentication types IP address The IP address of the RADIUS server Port A port of the RADIUS server The password which the access point uses for communication with RADIUS encryption key the RADIUS server the value of this parameter is specified in the RADIUS server settings An encryption method TKIP available only for the WPA WPA Encryption authentication type AES available only for the WPA2 and WPA WPA2 mixed authentication types The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field the key is not renewed Click the Next button to continue When all the steps of confi
5. Device mode page you can change the operating mode of the device DAI ink System x Language v DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP Device work mode settings Work mode Router Figure 134 The page for changing the operating mode of the device To switch the device to the other mode select the Access point value from the Work mode drop down list and click the Change button Then select the Save amp Reboot value from the top page menu displayed when the mouse pointer is over the System caption and wait until the device is rebooted Page 153 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Remote Access On the Advanced Remote access page you can configure access to the web based interface of the access point By default the access from external networks to the access point is closed If you need to allow access to the access point from the external network create relevant rules System v Language v D Link DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP Remote access configuration for web interface IP address Mask Public port Protocol HTTP 192 168 161 0 255 255 255 0 80 Figure 135 The Advanced Remote access page To create a new rule click the Add button Page 154 of 1
6. MACHAPv2 or AUTO value is selected from the Authentication algorithm drop down list Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value MTU The maximum size of units transmitted by the interface Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive Keep Alive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the required values Advanced options of the pppd daemon which need to be specified Extra options for this connection Optional Select the checkbox if you want the access point to establish connection to the Internet on demand In the Maximum idle time field specify a period of inactivity in seconds after which the connection should be terminated PPP debu Select the checkbox if you want to log all data on PPP connection 2 debugging IP received The IP address assigned by the ISP Enable RIP Select the checkbox to allow using RIP for this connection NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Page 116 of 175 Dial on demand DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description Select the checkbox to enable protection against ARP and DDoS attacks When all needed se
7. Parameter Description An operating mode of the access point s DHCP server Enable the access point assigns IP addresses to clients automatically in accordance with the specified parameters When this value is selected the Start IP End IP and the Lease time fields are displayed on the page Disable the access point s DHCP server is disabled clients IP addresses are assigned manually Relay an external DHCP server is used to assign IP addresses to clients When this value is selected the External DHCP server IP field is displayed on the page The start IP address of the address pool used by the DHCP server to distribute IP addresses to clients The end IP address of the address pool used by the DHCP server to distribute IP addresses to clients The lifetime of IP addresses leased by the DHCP server At the end of this period the leased IP address is revoked and can be distributed to another device unless the previous device has confirmed the need to keep the address External DHCP server IP The IP address of the es DHCP server which assigns IP addresses to the access point s clients When all needed settings are configured click the Save button Lease time Page 40 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Access Point Mode Wi Fi In this menu you can specify all needed settings for your wireless network Common settings On the Wi Fi Common set
8. If you want to disable your WLAN deselect the Enable Wireless checkbox The access point allows splitting your WLAN into several parts up to four with their own names SSIDs and unique identifiers BSSIDs To split the network into several parts select a relevant value 2 3 or 4 from the MBSSID drop down list By default the wireless network is not splitted the Disabled value is selected from the list The value from the BSSID drop down list is the unique identifier for your Wi Fi network You cannot change the value of this parameter it is determined in the device s internal settings If you have splitted your WLAN into parts the BSSID drop down list contains several values Each identifier corresponds to a single part of the WLAN For every part of the WLAN you can specify a name SSID security settings rules for MAC filtering and enable the WMM function if needed To specify these values select the needed part from the BSSID drop down list and click the Change button Then proceed to the relevant page of the Wi Fi menu section Page 125 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Basic Settings On the Wi Fi Basic settings page you can configure basic parameters of the device s WLAN DAI ink System X Language v DAP 1150 Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS
9. When all needed settings are configured click the Save button Page 122 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode LAN To configure the access point s local interface proceed to the Net LAN page IP Address 192 168 0 50 Netmask 255 255 255 0 Figure 109 Basic settings of the local interface If needed edit the basic settings of the local interface Parameter Description IP Address The IP address of the access point in the local subnet By default the following value is specified 192 168 0 50 The mask of the local subnet By default the following value is specified 255 255 255 0 When needed settings are configured click the Save button In the Static DHCP section you can specify MAC address and IP address pairs set a fixed IP address in the local area network for a device with a certain MAC address The access point assigns IP addresses in accordance with the specified pairs only when the DHCP server is enabled in the DHCP server section in the Mode drop down list the Enable value is selected Static DHCP lt Select IP MAC address gt Figure 110 The section for creating MAC IP pairs To create a MAC IP pair click the Add button Enter the MAC address of the device from the LAN in the MAC address field and an IP address which will be assigned to this device in the IP address field In the Host name field specify a network name
10. 1B 11 30 2C 62 802 11b g 1 WPA2 PSK TKIP aul 100 DIR 620 F0 7D 68 76 BC CO 802 11b g n 1 Open net all 100 dlink103 00 22 B0 B5 AA 6C 802 11b g n 1 Open net a 39 DIR 300NRU 00 26 5A 2E EA A0 802 11b g n 1 Open net all 99 DIR 620 00 52 40 E4 00 00 802 11b g n 1 Open net al 55 3 DIR 456 8C 44 35 01 87 07 802 11b g 1 Open net WEP all 100 DSL 2750U 1C 7E E5 B4 0B DC 802 11b g n 6 Open net all 100 dlink2360 5C D9 98 02 EA 38 802 11b g n 6 Open net at 60 D Link 00 21 91 55 91 15 802 11b g 6 WPA2 PSK AES all 86 DIR 632 5C D9 98 63 F5 88 802 11b g 6 Open net anil 100 DSL 2650U 34 08 04 EB 7F FE 802 11b g n 6 Open net anil 100 DSL 2640U 34 08 04 EB 87 84 802 11b g n 6 Open net all 100 DIR 615WPS 00 9A 4A 02 05 0C 802 11b g n 11 WPA2 PSK AES all 100 MTS ROUTER 00 24 01 B1 FA 48 802 11b g 11 PA2 PSK AES anil 100 DIR 615bu 00 90 4C 08 00 0C 802 11b g n 11 Open net all 100 dlink1360 1C 7E E5 2F 84 A8 802 11b g n 13 Open net all 81 SSID BSSID Network Authentication Open WEP Encryption settings Enable Encryption WEP m L d Figure 51 The page for configuring the client mode To configure the access point as a client select the Enable client checkbox When the checkbox is selected the following fields are displayed on the page Parameter Description SSD The name of the network to which the access point connects The unique identifier of the
11. Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client WMM E Parameters of Access Point AC Aifsn CWMin CWMax Txop ACM Ack AC_BK 7 lv 1023 v 0 AC_BE 3 15 y 63 y 0 AC_VI 1 7 15 Y 94 AC_vO 1 3 7v 47 Parameters of Station AC Aifsn CWMin CWMax Txop ACM AC_BK 7 15 y 1023 v 0 AC_BE 3 iv 1023 v 0 AC_VI 2 7 y 15 v 94 AC_VO 2 3 yv 7 47 ES Change Figure 49 The page for configuring the WMM function i All needed settings for the WMM function are specified in the device s system It is m recommended not to change the default values The WMM function allows assigning priorities for four Access Categories AC AC_BK Background low priority traffic print jobs file downloads etc AC_BE Best Effort traffic from legacy devices or devices applications that do not support QoS AC_VI Video AC VO Voice Parameters of the Access Categories are defined for both the access point itself in the Parameters of Access Point section and wireless devices connected to it in the Parameters of Station section Page 58 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual For every Access Category the following fields are available Parameter Description Arbitrary Inter Frame Space Number This parameter influences Aifsn time delays for the relevant Access Category The lower the value
12. Channel ae access point itself chooses the channel with the least interference Operating mode of the wireless network of the access point This Wireless mode parameter defines standards of the devices that will be able to use your wireless network Select a value from the drop down list The maximum number of devices connected to the wireless network Max Associated Clients of the access point When the value 0 is specified the device does not limit the number of connected clients When you have configured the parameters click the Change button Page 42 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Security Settings On the Wi Fi Security settings page you can modify security settings of the WLAN D Li ni 4 System X Language X DAP 1150 Wi Fi Advanced Firewall System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Network Authentication Open WEP Encryption settings Enable Encryption WEP al Figure 38 The default security settings By default the Open network authentication type with no encryption is specified for the WLAN The default security settings do not provide sufficient protection for the WLAN Please specify your own security settings for the WLAN or each part of the WLAN if the network was splitted into parts Page 43 of 175 DAP 1150 Wireless Access Poi
13. Encryption Key WEP 4 Figure 116 The Open value is selected from the Network Authentication drop down list Parameter Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field the Encryption Key WEP as Enable Encryption WEP HEX checkbox and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected The number of the key from first to fourth which will be used for Default Key ID WEP encryption Encryption Key WEP as Select the checkbox to set a hexadecimal number as a key for HEX encryption Keys for WEP encryption The access point uses the key selected from the Default Key ID drop down list It is required to specify all the fields Encryption Key WEP 1 4 You can specify keys containing 5 or 13 symbols use digits and or Latin characters If the Encryption Key WEP as HEX checkbox is selected you can specify only keys containing 10 symbols the digits 0 9 and the characters A F Page 129 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed value is selected the WPA Encryption settings section is displayed Network Authentication WPA2 PSK gt Encryption Key PSK 76543210 WPA2 Pre authentication T WPA Encryption settings WPA Encryption TKIP WPA reneval 3600 Figure
14. IP WAN connection Parameter Description Select a method of MPPE encryption No encrypt MPPE encryption is not applied MPPE 40 128 bit MPPE encryption with a 40 bit or 128 bit key is applied Encryption MPPE 40 bit MPPE encryption with a 40 bit key is applied MPPE 128 bit MPPE encryption with a 128 bit key is applied MPPE encryption can be applied only if the MSCHAP MACHAPv2 or AUTO value is selected from the Authentication algorithm drop down list Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value The maximum size of units transmitted by the interface Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive Keep Alive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the required values i Advanced options of the pppd daemon which need to be specified Extra options for this connection Optional Select the checkbox if you want the access point to establish connection to the Internet on demand In the Maximum idle time Dial on demand EE aes field specify a period of inactivity in seconds after which the connection should be terminated PPP debug Select the checkbox if you want to log all data on PPP connection debugging The IP address assigned by the ISP Click the Next button to continue
15. List WPS WDS Additional settings WMM Client Enable dient Y List of wireless networks Available wireless networks 14 Unknown wireless networks 0 SSID BSSID Wireless mode Channel Network Authentication Signal level 2 Open net 100 Develop 00 18 11 30 2C 62 802 11b g WPA2 PSK TKIP il 100 Home 00 52 40 E4 00 00 802 11b g n 1 Open net at 55 DIR 300NRU 1C 7E E5 8E A3 EC 802 11b g n 1 Open net alll 919 DIR 300NRU 1C 7E E5 8E A0 8C 802 11b g n 1 Open net a 34 dlink2553 F0 7D 68 67 D0 B7 802 11b g n 1 Open net alll 99 DIR 456 8C 44 35 01 87 07 802 11b g 1 Open net WEP all 100 DIR 620 F0 7D 68 76 BC C0 802 11b g n 1 Open net all 100 DIR 300NRU 00 26 5A 2E EA AO 802 11b g n 1 Open net alll 949 DIR 632 5C D9 98 63 F5 22 802 11b g 6 WPA PSK WPA2 PSK mixed AES all 100 D Link 00 21 91 55 91 15 802 11b g 6 WPA2 PSK AES all 100 DIR 615RU 20 10 52 19 58 36 302 11b g 6 WPA PSK WPA2 PSK mixed AES nil 100 dlink 1C BD B9 E4 5E 9C 802 11b g n 11 Open net all 81 107 1C AF F7 69 D1 42 802 11b g 13 Open net 5 SSID DIR 620 BSSID 00 0D 56 64 52 22 Network Authentication Open m WEP Encryption settings __ Enable Encryption WEP Figure 127 The page for configuring the client mode To configure the access point as a client select the Enable client checkbox When the checkbox is selected the following fields are displayed on the page Parame
16. Service Provider L2TP Layer 2 Tunneling Protocol LAN Local Area Network LCP Link Control Protocol MAC Media Access Control MTU Maximum Transmission Unit NAT Network Address Translation NTP Network Time Protocol OFDM Orthogonal Frequency Division Multiplexing PBC Push Button Configuration PIN Personal Identification Number Page 174 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Abbreviations and Acronyms User Manual PPPoE Point to point protocol over Ethernet PPTP Point to point tunneling protocol PSK Pre shared key QoS Quality of Service RADIUS Remote Authentication in Dial In User Service RIP Routing Information Protocol RTS Request To Send SSID Service Set Identifier TKIP Temporal Key Integrity Protocol UDP User Datagram Protocol UPnP Universal Plug and Play URL Uniform Resource Locator WAN Wide Area Network WDS Wireless Distribution System WEP Wired Equivalent Privacy Wi Fi Wireless Fidelity WISP Wireless Internet Service Provider WLAN Wireless Local Area Network WMM Wi Fi Multimedia WPA Wi Fi Protected Access WPS Wi Fi Protected Setup Page 175 of 175
17. button Page 165 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual System In this menu you can do the following e change the password used to access the access point s settings e save the current settings to the non volatile memory e create a backup of the access point s configuration e restore the access point s configuration from a previously saved file e restore the factory default settings e view the system log e update the firmware of the access point e configure automatic synchronization of the system time e allow or forbid access to the access point via TELNET Administrator Password On the System Administrator password page you can change the password for the administrator account used to access the web based interface of the access point and to access the device settings via TELNET i For security reasons it is strongly recommended to change the administrator password upon initial configuration of the access point D Link a a DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP dient Telnet System password setting up The system password and the password for the web based interface wil be changed at the same time Login admin v Password Confirmation Figure 148 The page for modifying the administrator password Enter the new passwo
18. button in the web based interface of the access point Page 53 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual WDS On the Wi Fi WDS page you can enable the WDS function and select a mode of this function The WDS function allows joining local area networks together via a wireless connection of access points D Li wuld 4 System X Language DAP 1150 panenna maa PR Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client WDS Mode Bridgemode v WDS Phy Mode CCK WDS Encryption NONE v WDS MAC 1 WDS MAC 2 WDS MAC 3 WDS MAC 4 Figure 47 The page for configuring the WDS function Page 54 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual The following fields are available on the page Parameter Description The WDS function mode Disable The function is disabled Bridge mode Access points communicate to each other only WDS Mode wireless devices cannot connect to them Repeater mode Access points communicate to each other wireless clients can connect to the WLAN created by interconnected access points A physical mode of data transfer between access points interconnected via the WDS function CCK 802 11b devices only WDS Phy M e MOAS OFDM 802 11g devices only HTMIX 802 11g and
19. containing 10 symbols the digits 0 9 and the characters A F Page 45 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed value is selected the WPA Encryption settings section is displayed Network Authentication WPA2 PSK gt Encryption Key PSK 76543210 WPA2 Pre authentication T WPA Encryption settings WPA Encryption TKIP WPA reneval 3600 Figure 41 The WPA2 PSK value is selected from the Network Authentication drop down list Parameter Description Encryption Key PSK A key for WPA encryption The key can contain digits and or Latin characters WPA2 Pre The checkbox activating preliminary authentication displayed only os for the WPA2 PSK and WPA PSK WPA2 PSK mixed authentication os authentication types WPA Encryption An encryption method TKIP AES or TKIP AES The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field the key is not renewed Page 46 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual When the WPA WPA2 or WPA WPA2 mixed value is selected the RADIUS settings and WPA Encryption settings sections are available Network Authentication WPA2 WPA2 Pre authentication E RADIUS settings IP address 192
20. down list and click the Change button Then proceed to the relevant page of the Wi Fi menu section Page 41 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Basic Settings On the Wi Fi Basic settings page you can configure basic parameters of the device s WLAN D Link a E DAP 1150 pisaa minnan lanin w PR Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Hide Access Point m SSID DAP 1150 Country RUSSIAN FEDERATION Channel auto v Wireless mode 802 11G only X When changing mode from B G on any of the modes with N is recommended to re tune security Max Associated Clients 0 Figure 37 Basic settings of the wireless LAN Parameter Description If the checkbox is selected other users cannot see your Wi Fi Hide Access Point network It is recommended not to select this checkbox in order to simplify initial configuration of your WLAN A name for the WLAN By default the value DAP 1150 is specified If your network is splitted into parts each part has the default name DAP 1150 2 DAP 1150 3 and DAP 1150 4 It is recommended to specify another name for the network upon initial configuration use digits and Latin characters The country you are in Select a value from the drop down list The wireless channel number When the auto value is selected the
21. edit the parameters of an existing server follow the link with the name of the server On the opened page change the needed parameters and click the Change button To remove an existing server follow the link with the name of the server On the opened page click the Delete button Page 161 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual DMZ A DMZ is a host or network segment located between internal local and external global networks In the access point the DMZ implements the capability to transfer a request coming to a port of the access point from the external network to a specified host of the internal network On the Firewall DMZ page you can specify the IP address of the DMZ host D Link a DAP 1150 Start Status Net WiFi Advanced Firewall Control System IP filters Virtual servers DMZ MAC filter Demilitarized zone settings Change Figure 142 The Firewall DMZ page To enable the DMZ select the Enabled checkbox enter the IP address of a host from your network in the IP address field To choose a device connected to the access point s LAN at the moment select the relevant value from the drop down list located to the right of the field the field will be filled in automatically and click the Change button Note that when the DMZ is enabled all traffic coming to a port of the WAN interface of the access point is directed
22. enable access via TELNET again select the On checkbox In the Port field enter the number of the access point s port through which access will be allowed by default the port 23 is specified Then click the Change button Page 70 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual CHAPTER 5 CONFIGURING DEVICE ROUTER MODE Setup Wizards Internet Setup Wizard To configure connection to the Internet click the Connect to internet button Internet connection wizard Get necessary information about Internet access type from Your provider You can add new connection based on this information You can go back from any step of the wizard to the main page by clicking on D Link logo Figure 61 Configuring connection to the Internet To create anew WAN connection click the add new connection link Page 71 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Internet connection wizard Select connection type PPPoE A connection of this type requires a username and password This type is used for connection via Ethernet or via DSL A connection of this type allows using a fixed IP address provided by your ISP Dynamic IP A connection of this type allows obtaining an IP address automatically from your ISP A connection of this type is protected by a special tunnel in the standard non protected
23. from the shortcut menu displayed Click the Next button to continue Page 78 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed change the connection settings available in the Miscellaneous section Internet connection wizard Mi A NA Enable RIP E Enable IGMP Multicast E NAT firewall Y lt Back Next gt Figure 70 Configuring Static IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection lect the check to all Iticast traffic fi th ternal Enable IGMP Multicast Select the checkbox to allow multicast traffic from the externa network e g video streaming to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS Firewall attacks Click the Next button to continue After that the page displaying all specified settings opens Click the Save button to create the connection or the Back button to specify other settings After clicking the Save button the quick settings page opens Page 79 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Dynamic IP Connection Internet connection wizard Connection name The connection name has been generated automatically according to t
24. generated When the value 0 is specified for this field the key is not renewed Click the Next button to continue When all the steps of configuring the WLAN are completed the specified settings are displayed on the page Check their correctness and then click the Save button After that you get to the quick settings page Page 99 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Status The pages of this section display data on the current state of the access point switched to the router mode e network statistics e the routing table e data on devices connected to the device s network and its web based interface Network Statistics On the Status Network statistics page you can view statistics for all interfaces connections existing in the system For each connection the following data are displayed state IP address subnet mask and gateway if the connection is established MAC address MTU value and volume of data received and transmitted with increase of the volume the units of measurement are changed automatically byte Kbyte Mbyte Gbyte D Li itil I c System v Language X DAP 1150 Status Net Wi Fi Advanced Firewall Control System Network statistics Routing table LAN dients Name Type Status IP Mask Gateway MAC MTU Rx Tx LAN up 192 168 1 179 255 255 255 0 F0 7D 68 8D 81 B2 1500 584 85 Kbyte 5 4125 Mbyte dynamic_WAN_1 ypO 192 168 1
25. has the category view the Category value is selected from the View by drop down list in the top right comer of the window choose the View network status and tasks line under the Network and Internet section Search Control Panel OE gt Control Panel All Control Panel Items gt Adjust your computer s settings View by Largeicons Y rm gt D Indexing Options Internet Options Keyboard Network and Sharing Location and Other EZ Center Mouse Sensors Performance Information and Tools E Personalization Phone and Modem Power Options law e E Notification Area Icons 2 Parental Controls bh LS Recovery Region and Language A kal Programs and Features Sound A el Deep Speech Recognition Connections 8 Sync Center Ba System GD Taskbar and Start Menu Windows CardSpace a f ll Troubleshooting BE User Accounts 5 Windows Defender a Windows Firewall ey Windows Update Figure 12 The Control Panel window 3 In the menu located on the left part of the window select the Change adapter settings line 4 In the opened window select the icon of the wireless network connection and make sure that your Wi Fi adapter is on 5 To open the list of available wireless networks select the icon of the wireless network connection and click the Connect To button or left click the network icon in the notification area located on the right side of the taskbar 16
26. is splitted into parts the value 2 3 or 4 is selected from the MBSSID drop down list on the Wi Fi Common settings page the WPS function can be used only for the first part of the WLAN the first value from the BSSID drop down list Before using the WPS function it is required to configure a type of WPA encryption DAI ink System X Language X DAP 1150 Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client _Enable Disable WPS _ WPS Enable E Change Information Default PIN code WPS Status Configured SSID DAP 1150 Network Authentication WPA2 PSK Encryption AES Encryption key 76543210 Refresh Reset to unconfigured Connection WPS Method PBC y Figure 122 The page for configuring the WPS function Page 135 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ae a Configuring Device Router Mode User Manual To activate the WPS function select the WPS Enable checkbox and click the Change button When the checkbox is selected the Information and Connection sections are available on the page Parameter Description The PIN code of the access point This parameter is used when Default PIN code connecting the access point to a registrar to set the parameters of the WPS function The state of the WPS function e Configured all needed settings are specified e Unconfigured you need
27. network This type is used by some ISPs It requires a username and password When this type is selected you can specify a fixed IP address for the non protected network before configuring the tunnel PPTP Dynamic IP A connection of this type is protected by a special tunnel in the standard non protected network This type is used by some ISPs It requires a username and password When this type is selected you automatically obtain an IP address for the non protected network from the ISP L2TP Static IP A connection of this type is protected by a special tunnel in the standard non protected network This type is used by some ISPs It requires a username and password When this type is selected you can specify a fixed IP address for the non protected network before configuring the tunnel L2TP Dynamic IP A connection of this type is protected by a special tunnel in the standard non protected network This type is used by some ISPs It requires a username and password When this type is selected you automatically obtain an IP address for the non protected network from the ISP Figure 62 The page for selecting the connection type On the opened page select the needed choice of the radio button and click the Next button Page 72 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual PPPoE Connection Internet connection wizard Connection name The connection
28. network to which the access point connects The authentication type of the network to which the access point connects Network Authentication Page 61 of 175 DAP 1150 Wireless Access Point Supporting Router Mode A Configuring Device Access Point Mode User Manual When the Open or Shared authentication type is selected the following fields are available Parameter Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected first to fourth which will fi Default Key ID The number at the key from first to fourth which will be used for WEP encryption Keys for WEP encryption The access point uses the key selected Encryption Key WEP 1 from the Default Key ID drop down list It is required to specify 4 all the fields You can specify keys containing 5 or 13 symbols use digits and or Latin characters When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed authentication type is selected the following fields are available Enable Encryption WEP Parameter Description WPA Encryption An encryption method TKIP AES or TKIP AES ion tain digit Lati Encryption Key PSK A key for WPA encryption The key can contain digits and or Latin characters When you have configured the parameters click the Change button In addition
29. of the PPPoE type click the Add button on the Net WAN page On the opened page select the PPPoE value from the Connection Type drop down list and specify the needed values General settings Connection Type PPPoE Port WAN Name _WAN_2 Enable Y Direction WAN ee O Ro eee ee ee eer eer MTU 1500 MAC FO 7D 68 8D 81 B2 lt Select address gt v Clone MAC Figure 97 The page for creating a new connection The General settings and Ethernet sections Parameter Description ern A MAC address assigned to the interface This parameter is mandatory if your ISP uses MAC address binding In the field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of MAC the network interface card of the computer that is being used to configure the access point at the moment as the MAC address of the WAN interface Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Page 104 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Without authorization E Password PE Password confirmation AA Service name Authentication algorithm AUTO MTU 1492 Keep Alive LCP interval sec LCP fails Dial on d
30. of the device for easier identification optional Also you can create a MAC IP pair for a device connected to the access point s LAN at the moment To do this select the relevant value from the Known IP MAC addresses drop down list the IP address and MAC address fields will be filled in automatically When all needed MAC IP pairs are specified click the Save button Existing MAC IP pairs are displayed in the table of the Static DHCP section To remove a pair select the relevant line in the table and click the Remove button Then click the Save button Page 123 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual In the DHCP server section you can configure the built in DHCP sever of the access point DHCP server Mode Enable w Start IP 192 168 0 51 End IP 192 168 0 100 Lease time min 86400 Figure 111 The section for configuring the DHCP server Parameter Description An operating mode of the access point s DHCP server Enable the access point assigns IP addresses to clients automatically in accordance with the specified parameters When this value is selected the Start IP End IP and the Lease time fields are displayed on the page Disable the access point s DHCP server is disabled clients IP addresses are assigned manually Relay an external DHCP server is used to assign IP addresses to clients When this value is selected the External DHCP
31. point s WLAN parameters left click the SSID of the WLAN the right column of the SSID line After clicking the line the Wi Fi Basic settings page opens see the Basic Settings section page 42 The web based interface of the access point is multilingual Select a needed language from the menu displayed when the mouse pointer is over the Language caption You can change the language of the web based interface in any menu item D Li ni 4 System Language X English DAP 1150 Pyccxwii YkpalHcoka T rkce Francais dual O Advanced Firewall System Figure 21 Changing the language of the web based interface After selecting the language the notification on unsaved changes will be displayed Click the Save button to save the current language of the web based interface as the default language Page 28 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Installation and Connection User Manual Saving and Restoring Settings Note that you should regularly save the changes of the device s settings to the non a volatile memory The web based interface displays the notification on unsaved changes at the top of the page Device configuration was changed Save Figure 22 The notification on unsaved changes You can save the device s settings via the top page menu displayed when the mouse pointer is over the System caption D Link System d Language X Reboot DAP 1150 Save8Reboot Save Backup Factory L
32. router mode hereinafter referred to as the access point is performed via the built in web based interface The web based interface is available from any operating system that supports a web browser Web Browser The following web browsers are recommended Windows Internet Explorer Mozilla Firefox or Opera For successful operation JavaScript should be enabled on the web browser Make sure that JavaScript has not been disabled by other software such as virus protection or web user security packages running on your computer Wired or Wireless NIC Ethernet or Wi Fi Adapter Any computer that uses the access point should be equipped with an Ethernet or Wi Fi adapter NIC If your computer is not equipped with such a device install an Ethernet or Wi Fi adapter prior to using the access point Wireless Connection Wireless workstations from your network should be equipped with a wireless 802 11b g or n NIC Wi Fi adapter In addition you should specify the values of SSID channel number and security settings defined in the web based interface of the access point for all these wireless workstations Page 13 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection Connecting to PC PC with Ethernet Adapter l 2 4 Make sure that your PC is powered off Connect an Ethernet cable between the LAN port located on the back panel of the access point and the Ethernet p
33. the network interface card of the computer that is being used to configure the access point at the moment as the MAC address of the WAN interface Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Netmask Gateway IP address Primary DNS server Secondary DNS server Miscellaneous Enable RIP Y Enable IGMP Multicast Y NAT Y firewall 9 Figure 104 The page for creating a new connection The IP and Miscellaneous sections Parameter Description IP Address Enter an IP address for this WAN connection Netmask Enter a subnet mask for this WAN connection Gateway IP Address Enter an IP address of the gateway used by this WAN connection Primary DNS server Enter addresses of the primary and secondary DNS servers in the Secondary DNS server relevant fields Enable RIP Select the checkbox to allow using RIP for this connection Page 114 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description Select the checkbox to allow multicast traffic from the external network e g video streaming to be received Enable IGMP Multicast Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the check
34. the page must be the same for all_ interconnected devices In addition it is required to set the same channel on the Wi Fi Basic settings page When you have configured the parameters click the Change button WDS Encryption Page 139 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Additional Settings On the Wi Fi Additional settings page you can define additional parameters for the WLAN of the access point l Changing parameters presented on this page may negatively affect your WLAN D Li n ll 4 System X Language X DAP 1150 Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Station Keep Alive o Beacon Period 100 RTS Threshold 2347 Frag Threshold 2346 DTIM Period 1 TX Power 100 BG Protection Auto Bandwidth 20 40MHz v TX Preamble Long Preamble Figure 124 Additional settings of the WLAN The following fields are available on the page Parameter Description The time interval in seconds between keep alive checks of wireless Station Keep Alive devices from your WLAN When the value O is specified the checking is disabled p The time interval in milliseconds between packets sent to Beacon Period synchronize the wireless network RTS Threshold The i size in bites of a packet for which an RTS frame is transmitt
35. to specify the relevant settings The name of the device s WLAN or the first part of the WLAN if the network is splitted into parts san The network authentication type specified for the WLAN or first k Authen n Network Authenticatio part of the WLAN Encryption a ooo type specified for the WLAN or the first part of the E The encryption key specified for the WLAN or the first part of the k Encryption key WLAN Click the button to view the latest data on the state of connecting the wireless device via the WPS function Reset to unconfigured Click the button to reset the parameters of the WPS function A method of the WPS function Select a value from the drop down list WES Merngg PIN Connecting the device via the PIN code PBC Connecting the device via the push button actual or virtual The PIN code of the WPS enabled device that needs to be connected to the wireless network of the access point PIN Code The field is displayed only when the PIN value is selected from the WPS Method drop down list Click the button to connect the wireless device to the WLAN of the Connect SN f access point via the WPS function Page 136 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode To add a wireless device via the PIN method of the WPS function follow the next steps l 2 3 4 T Select the WPS Enable checkbox Click the Change button Select the PI
36. to the same port of the specified IP address Also note that virtual servers have higher priority than the DMZ host In other words if there has been created a virtual server that directs traffic from external port 80 to a port of the device from the local network of the access point then entering http access point WAN IP in the address bar users of the external network are directed to the specified port and IP address configured for the virtual server but not to port 80 of the device with the IP address specified on the Firewall DMZ page To disable the DMZ deselect the Enabled checkbox and click the Change button Page 162 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual MAC Filter On the Firewall MAC filter page you can configure MAC address based filtering for computers of the device s LAN D Link men osl men o DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System IP filters Virtual servers DMZ MAC filter MAC filter configuration You can add edit and delete addresses here MAC address Action Figure 143 The Firewall MAC filter page To specify a new address for the MAC filter click the Add button D Link System X Language v DAP 1150 Start Status Net Wi Fi Advanced Firewall IP filters Virtual servers DMZ MAC filter MAC address editing MAC address lt Select address gt bd Action Allow Figure 144 T
37. value is selected devices WPA PSK WPA2 PSK using the WPA PSK authentication type and devices using the mixed WPA2 PSK authentication type can connect to the WLAN of the access point y The WPA WPA2 and WPA WPA2 mixed authentication types require a RADIUS m server Page 33 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Access Point Mode When the Open or Shared value is selected the WEP Encryption settings section is displayed the section is unavailable for the wireless network operating modes which support the standard 802 11n Security settings Network Authentication WEP Encryption settings Enable Encryption WEP Default Key ID Encryption Key WEP as HEX Encryption Key WEP 1 Encryption Key WEP 2 Encryption Key WEP 3 Encryption Key WEP 4 Next gt Figure 28 The Open value is selected from the Network Authentication drop down list Parameter Enable Encryption WEP Default Key ID Encryption Key WEP as HEX Encryption Key WEP 1 4 Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field the Encryption Key WEP as HEX checkbox and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected The number of the key from first to fourth which will be used for WEP encryption Select the checkbox to se
38. when the Enable client checkbox is selected the list of available wireless networks is displayed on the page The Unknown wireless networks field shows the number of hidden wireless networks To view the latest data on the available wireless networks click the Search button To connect to a wireless network from the list select the needed network Upon that the relevant values are automatically inserted in the SSID BSSID and Network Authentication fields For the Open authentication type with no encryption click the Change button For the Open authentication type with encryption and the Shared authentication type select a needed value from the Default Key ID drop down list fill in 4 Encryption Key WEP fields and click the Change button For the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed authentication types fill in the Encryption Key PSK field and click the Change button After clicking the Change button the wireless channel of DAP 1150 will switch to the channel of the wireless access point to which you have connected If the access point is connected to the selected network successfully the green indicator appears to the right of the network s SSID in the table Page 62 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Advanced This menu is designed for switching the operating modes of the device Device mode On the Advanced Device mode page
39. 10 100 Adapter A This connection uses the following items O SF NWLink NetBIOS A AF NWLink IP lt SPX NetBIOS Compatible Transport Prot y Internet Protocol TCP IP lt Description Transmission Control Protocol lnternet Protocol The default wide area network protocol that provides communication across diverse interconnected networks E Show icon in notification area when connected Figure 4 The Local Area Connection Properties window Page 15 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection 4 Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons Click the OK button Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address lly S Figure 5 The Internet Protocol TCP IP Properties window 5 Click the OK button in the connection properties window Now your computer is configured to obtain an IP address automatically Page 16 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection Obtaining IP Address Auto
40. 117 The WPA2 PSK value is selected from the Network Authentication drop down list Parameter Description Encryption Key PSK A key for WPA encryption The key can contain digits and or Latin characters The checkbox activating preliminary authentication displayed only for the WPA2 PSK and WPA PSK WPA2 PSK mixed authentication types WPA Encryption An encryption method TKIP AES or TKIP AES The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field WPA2 Pre authentication the key is not renewed Page 130 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the WPA WPA2 or WPA WPA2 mixed value is selected the RADIUS settings and WPA Encryption settings sections are available Network Authentication WPA2 WPA2 Pre authentication T an ee IP address 192 168 0 254 Port 1812 RADIUS encryption key dlink WPA Encryption settings WPA Encryption AES WPA reneval 3600 Figure 118 The WPA2 value is selected from the Network Authentication drop down list Parameter Description WPA2 Pre The checkbox activating preliminary authentication displayed only authentication for the WPA2 and WPA WPA2 mixed authentication types IP address The IP address of the RADIUS server Oo Pot A port of the RADIUS server The password which the access point uses for commu
41. 14 13 10 2011 1 Figure 13 The notification area of the taskbar Page 23 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection 6 In the opened window in the list of available wireless networks select the wireless network DAP 1150 and click the Connect button Not connected 4 mi Connections are available Wi Fi A wireless router wil Open Network and Sharing Center Figure 14 The list of available networks 7 Wait for about 20 30 seconds After the connection is established the network icon will be displayed as the signal level scale If you perform initial configuration of the access point via Wi Fi connection note that immediately after changing the wireless default settings of the access point you will need to reconfigure the wireless connection using the newly specified settings Page 24 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Installation and Connection User Manual Connecting to Web based Interface When you have configured your computer you can access the web based interface and configure needed parameters configure the wireless network change the operating mode of the device specify the settings of the firewall etc l Ze Start a web browser see the Before You Begin section page 13 In the address bar of the web browser enter the IP address of the access point by default the following IP a
42. 168 0 254 Port 1812 RADIUS encryption key dlink WPA Encryption settings WPA Encryption AES WPA reneval 3600 Figure 42 The WPA2 value is selected from the Network Authentication drop down list Parameter Description WPA2 Pre The checkbox activating preliminary authentication displayed only authentication for the WPA2 and WPA WPA2 mixed authentication types IP address The IP address of the RADIUS server Oo Pot A port of the RADIUS server The password which the access point uses for communication with RADIUS encryption key the RADIUS server the value of this parameter is specified in the RADIUS server settings An encryption method TKIP available only for the WPA WPA Encryption authentication type AES available only for the WPA2 and WPA WPA2 mixed authentication types The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field the key is not renewed When you have configured the parameters click the Change button Page 47 of 175 DAP 1150 Wireless Access Point Supporting Router Mode A Configuring Device Access Point Mode User Manual MAC Filter On the Wi Fi MAC Filter page you can define a set of MAC addresses of devices which will be allowed to access the WLAN or define MAC addresses of devices which will not be allowed to access the WLAN D Link emool m o DAP 1150 Wi Fi Advanced Firew
43. 61 212 255 255 255 0 192 168 161 1 F0 7D 68 8D 81 B2 1500 11 348 Mbyte 28 006 Mbyte Figure 93 The Status Network statistics page Page 100 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Routing Table The Status Routing table page displays the information on routes The table contains destination IP addresses gateways subnet masks and other data DAI ink System X Language v DAP 1150 pa Status Net Wi Fi Advanced Firewall Control System Network statistics Routing table LAN dients Interface Destination Gateway Mask Flags Metric dynamic_WAN_1 192 168 161 0 0 0 0 0 255 255 255 0 u 0 LAN 192 168 1 0 0 0 0 0 255 255 255 0 u 0 dynamic_WAN_1 192 168 0 0 192 168 161 240 255 255 255 0 UG 2 dynamic_WAN_1 0 0 0 0 192 168 161 1 0 0 0 0 UG 100 Figure 94 The Status Routing table page Page 101 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual LAN Clients On the Status LAN clients page you can view the list of devices connected to the access point and devices accessing its web based interface DA ink System X Language v DAP 1150 paan Status Net Wi Fi Advanced Firewall Control System Network statistics Routing table LAN clients IP address Flags MAC address Interface 192 168 161 143 0x2 6C 62 6D 7D 26 A1 dynamic_WAN_1 Figure 95 The Status
44. 7 Advanced settings MBSSID Disabled v BSSID FO 7D 68 8D 81 B2 v Figure 86 Common and advanced settings of the wireless LAN On the opened page in the Common settings section select the Enable Wireless checkbox if 1t was deselected before to enable Wi Fi connections In the Advanced settings section you can split your network into several parts To do this select the relevant value 2 3 or 4 from the MBSSID drop down list Click the Next button to continue In the Basic settings section you can change the basic parameters of your access point s WLAN hide your wireless network Hide Access Point specify a name for the network SSID select your location Country and the wireless channel number Channel specify the operating mode Wireless Mode and the maximum number of devices connected to the wireless network Max Associated Clients Basic settings Hide Access Point SSID DAP 1150 Country RUSSIAN FEDERATION v Channel 13 v Wireless mode 802 11 G only v When changing mode from B G on any of the modes with N is recommended to re tune security Max Associated Clients 0 lt Back Next gt Figure 87 Basic settings of the wireless LAN Click the Next button to continue Page 94 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual On the next page you can modify security settings of the WLAN By default the Open n
45. 75 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual D Link DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP Remote access rule editing aha PWN s IP address lt Select address gt v Mask Protocol HTTP Public port Figure 136 The page for adding a rule for remote management You can specify the following parameters Parameter Description IP address A host or a subnet to which the rule is applied The protocol available for remote management of the access point Public port An external port of the access point You can specify only one port Click the Change button To edit a rule for remote access click the relevant link On the opened page change the needed parameters and click the Change button To remove a rule for remote access click the relevant link On the opened page click the Delete button Page 155 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual IGMP On the Advanced IGMP page you can enable IGMP for the access point IGMP is used for managing multicast traffic transferring data to a group of destinations This protocol allows using network resources for some applications e g for streaming video more efficiently D Link mo DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routin
46. 802 11n devices GREENFIELD 802 11n devices only A type of encryption for data transfer between access points interconnected via the WDS function NONE No encryption WEP TKIP AES A key for the specified type of encryption If the NONE value is Encryption Key selected from the WDS Encryption drop down list the field is not displayed f devi ted to th int via th WDS MAC 1 4 The MAC addresses of devices connected to the access point via the WDS function The WDS function parameters specified on the page must be the same for all_ interconnected devices In addition it is required to set the same channel on the Wi Fi Basic settings page WDS Encryption When you have configured the parameters click the Change button Page 55 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Additional Settings On the Wi Fi Additional settings page you can define additional parameters for the WLAN of the access point I Changing parameters presented on this page may negatively affect your WLAN D J ink System X Language DAP 1150 A wen d Frewall System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Station Keep Alive 0 Beacon Period 100 RTS Threshold 2347 Frag Threshold 2346 DTIM Period 1 TX Power 100 BG Protection Auto ks Bandwidth 20 40MHz v
47. AN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Netmask Gateway IP address Primary DNS server Secondary DNS server Miscellaneous Enable RIP Enable IGMP Multicast NAT Y firewall Y Figure 100 The page for creating a new connection The IP and Miscellaneous sections Parameter Description IP Address Enter an IP address for this WAN connection Netmask Enter a subnet mask for this WAN connection Gateway IP Address Enter an IP address of the gateway used by this WAN connection Primary DNS server Enter addresses of the primary and secondary DNS servers in the Secondary DNS server relevant fields Enable RIP Select the checkbox to allow using RIP for this connection Page 108 of 175 DAP 1150 Wireless Access Point Supporting Router Mode x 3 Configuring Device Router Mode User Manual Parameter Description Select the checkbox to allow multicast traffic from the external Enable IGMP Multicast l f network e g video streaming to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks When all needed settings are configured click the Save button Page 109 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring D
48. AP 1150 Net WiFi Advanced Firewall Control TP filters Virtual servers DMZ MAC filter Se Name Protocol TCP UDP y Action ts AA OS An eso nace aerate For entering IP address type 32 as subnet bit mask field after ACCEPT v IP addresses range o Source lt Select address gt v Destination lt Select address gt v Ports You can specify either a port or port range and several 80 8080 or 400 500 Source Destination Figure 139 The page for adding a rule for IP filtering You can specify the following parameters Parameter Description IP filter rule editing Name A name for the rule for easier identification A protocol for network packet transmission Select a value from the Protocol drop down list Select an action for the rule ACCEPT Allows packet transmission in accordance with the criteria specified by the rule DROP Denies packet transmission in accordance with the criteria specified by the rule IP Addresses Select the checkbox if you want to specify a range of IP addresses as the source or destination IP address IP address range Page 158 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description The source host subnet IP address If the IP address range checkbox is selected specify the starting IP address of the range in the Source first field and the ending IP address in th
49. D Link User Manual DAP 1150 Wireless Access Point Supporting Router Mode December 2011 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Contents Chapter 1 Introduction 0 604 nis ed Meek Ree a ke a 5 Contents and AuPLence snee ee ea ea is A a Ie etre de dae we Le a S 5 CONVENE LONS ti A eked ee Se hee ney a Bin O ta As OE aie By eNews iS 5 Document SELUCCULE ii ii Sea ee eye gel aie eae ed ews De GIS Se wae eae See Da ote abe Be 5 Chapter 2 OVEEVIL OW seeicc d a A a edie Mew Sees 6 Gen ral Information iin the CAE he oe in eee ees a lee A a a Li oe ed 6 Spe cifica ti nsS owe ied n Se AS ee ee ee Be eek ae See hk ee toe OR a a S 7 Product AppGaranCe munici a a wee ne ge Pea ae brag Wwe aye eg Sabena fee wl E ds 10 HPO Panel A se Scan seen ct cas Lane pans nta dd 10 Back Panels soii Stak wid wh eB A fe een E ee Syne AEN A ARA a E E Site ALA 11 Delivery Packages 22 2 as Soe a ee ee kee ech oe eee a Seles 4 12 Chapter 3 Installation and Connection 13 Before You BOT Seale oe ma Ses SRE AE A ae Gas oe Ske eee Glee Fee eg la 13 CONNECTING to Plinio anar A Be Se eae a e gS 14 PC with Ethernet Adaptec A A a ee Sha eels 14 Obtaining IP Address Automatically in OS Windows XP oooooooooooo ooo 14 Obtaining IP Address Automatically in OS Windows T oooooooooooooooooo 17 PC With WISSEL AJAPprtS Ens At a ie Sa CAN ds a eis ad Co
50. GA SPURS ue alley E iria Me R 50 ROVING T fe oe A Ge dy a a a a ace a Gee AS Sine i tte ii Salto Device Modens ses meia oe 5 A E EA te aang fe bee teak Ma A a OO REMOTE ACCES Seme A Ri A e ad 54 TEMP a 6 bese rs ys A A Seg NS Sot Ge ous ERAS A 56 Firewall iii be woke nee as eh Pe oe he he Se is nn he ES wdc 157 TP BES cl OS psd AAA TAS ARIS AS ES SEAS ASA A a SIE 57 Virtual SCENES SS a Te ai E IL gaged Saha POE Dee Geller wig a late ria Aan eee 60 DMA ase So Nowe 20a AS ES sane sei hed O E US E DAS AS ro elem eet D ei dnd 62 MAC RULE is ages a SMe DS A A de a aa es OS CONTO A A A A SS ated A Died AD EG A 164 URL PERE SIE AA A OSD Sond Gra ct OA NA A A A A A AS 166 Administrator PassWord teretane sedea iE AA A TA A O CONE VOUT ALTO A A A a ave lnea LOD System A ER Eee Se Sa ees we bo ee 68 ETEMWare UPO Talitas one 4 va anaiai A A te ab A le Mule er ashe Oat iia ts EDO NDB CS iG ai A A A egg MS hte A A a laos AA Se eee a tas a reas rele HEL IN A SAE apes Zar NANA Chapter 6 Operation GuidelineS o ooooooocoooncooooo 173 Safety Instructions wei ei A A A Seca BIE a eee A AA Sees oe 9 A 173 Wireless Installation Considerations 0 0 ccc eee eee eee ee ee eee 173 Chapter 7 Abbreviations and ACronyMS oo oooooooo ooo 174 Page 4 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Introduction CHAPTER1 INTRODUCTION Contents and Audience This manual des
51. If needed change the connection settings available in the Miscellaneous section Internet connection wizard jp ds Enable RIP Y Enable IGMP Multicast 7 NAT 7 firewall Y lt Back Next gt Figure 82 Configuring PPTP Dynamic IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection heck to all Iticast traffic fi th t 1 Enable IGMP Multicast Select the c ec box to al ow mu icast raffic from the externa network e g video streaming to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Click the Next button to continue Page 89 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Internet connection wizard 5 AAA Connect automatically 7 Username Without authorization F Password senos Password confirmation en VPN server address Advanced PPP settings Encryption No encrypt v Authentication algorithm AUTO MTU 1456 Keep Alive im Extra options Dial on demand PPP debug IP received lt Back Next gt Figure 83 Configuring PPTP Dynamic IP WAN connection Leave the Connect automatically checkbox selected to allow automatic start of the connection upon the load of the access point In t
52. LAN clients page For each device the following data are displayed the IP address the MAC address and the interface to which the device is connected Page 102 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Net In this menu you can configure basic parameters of the local area network of the access point and configure connection to the Internet a WAN connection WAN On the Net WAN page you can create and edit connections used by the access point D Link mmn ol eaae o DAP 1150 Wi Fi Advanced Firewall Control System WAN LAN Name Connection Type Port Status Direction Default gateway E Figure 96 The Net WAN page To create a new connection click the Add button On the page displayed specify the relevant values To edit an existing connection left click the relevant line in the table On the page displayed change the parameters and click the Save button To delete an existing connection left click the relevant line in the table On the page displayed click the Delete button To use one of existing WAN connections as a default gateway select the choice of the Default gateway radio button located in the line corresponding to this connection Page 103 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Creating PPPoE WAN Connection To create a connection
53. Log into the web based interface using the login admin and the current password Nw PO Select the Factory line in the top page menu displayed when the mouse pointer is over the System caption 7 Wait until the access point is rebooted Log into the web based interface using the default IP address login and password 192 168 0 50 admin admin 4 The name of the button depends upon the web browser that you use Page 170 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual NTP Client On the System NTP client page you can configure automatic synchronization of the system time with a time server on the Internet System X Language kd D Link DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP client Telnet Enabled Change Figure 153 The System NTP client page To enable automatic synchronization with a time server l Select the Enabled checkbox 2 Select your time zone 3 Specify the needed NTP server in the NTP servers field or leave the server specified by default 4 Click the Change button When the access point is powered off or rebooted the system time is reset to the default value If you have set automatic synchronization for the system time the internal clock of the device will be configured after connecting to the Internet P
54. N value from the WPS Method drop down list Select the PIN method in the software of the wireless device that you want to connect to the WLAN ofthe access point Click the relevant button in the software or on the cover of the wireless device that you want to connect to the WLAN Right after that enter the PIN code specified on the cover of the wireless device or in its software in the PIN Code field Click the Connect button in the web based interface of the access point To add a wireless device via the PBC method of the WPS function follow the next steps l 2 3 4 Select the WPS Enable checkbox Click the Change button Select the PBC value from the WPS Method drop down list Select the PBC method in the software of the wireless device that you want to connect to the WLAN ofthe access point Click the relevant button in the software or on the cover of the wireless device that you want to connect to the WLAN Click the Connect button in the web based interface of the access point Page 137 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual WDS On the Wi Fi WDS page you can enable the WDS function and select a mode of this function The WDS function allows joining local area networks together via a wireless connection of access points D Li vil le 4 System X Language DAP 1150 pa tin Wi Fi Advanced Firewall Control System Common setti
55. Password and Password confirmation fields the password provided by your ISP If authorization is not required select the Without authorization checkbox If needed specify additional settings for your PPPoE WAN connection Internet connection wizard A O A E iri E A A A Username Without authorization i Password esca o Password confirmation s Advanced PPP settings Service name Authentication algorithm AUTO v MTU 1492 Keep Alive Y LCP interval sec 30 Dial on demand PPP IP extension Use Static IP Address PPP debug PPPoE pass through LCP fails 3 lt Back Next gt Figure 65 Configuring PPPoE WAN connection Parameter Description The name of the PPPoE authentication server Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value The maximum size of units transmitted by the interface Page 74 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Parameter Keep Alive Dial on demand PPP IP extension Use Static IP Address PPP debug PPPoE pass through Description Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the
56. Rename this connection Disable Status Diagnose Bridge Connections Create Shortcut Delete Properties Figure 8 The Network Connections window Page 19 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection 5 In the Local Area Connection Properties window on the Networking tab select the Internet Protocol Version 4 TCP IPv4 line Click the Properties button Networking Connect using ay This connection uses the following items Y 9 Client for Microsoft Networks M J QoS Packet Scheduler M Ol File and Printer Sharing for Microsoft Networks M Internet Protocol Version 6 TCP IPw6 RS Internet Protocol Version 4 TCP IP v4 Y Link Layer Topology Discovery Mapper 1 0 Driver Y Link Layer Topology Discovery Responder Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Figure 9 The Local Area Connection Properties window Page 20 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Installation and Connection User Manual 6 Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons Click the OK button Internet Protocol Version 4 TCP IPv4 Properties Sa General Alternate Configu
57. TX Preamble Long Preamble v Change Figure 48 Additional settings of the WLAN The following fields are available on the page Parameter Description The time interval in seconds between keep alive checks of wireless Station Keep Alive devices from your WLAN When the value O is specified the checking is disabled The time interval in milliseconds between packets sent to Beacon Period synchronize the wireless network RTS Threshold The minimum size in bites of a packet for which an RTS frame is transmitted The maximum size in bites of a non fragmented packet Larger Frag Threshold packets are fragmented divided The time period in seconds between sending a DTIM a message DTIM Period notifying on broadcast or multicast transmission and data transmission The transmit power in percentage terms of the access point Page 56 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Parameter Description The 802 11b and 802 11g protection function is used to minimize collisions between devices of your wireless network Select a value from the drop down list Auto The protection function is enabled and disabled automatically depending on the state of the network this value is recommended i your wireless local area network consists of both 802 11b and 802 11g devices BG Protection Always On The protection function is al
58. The number of the key from first to fourth which will be used for WEP encryption Encryption Key WEP as Select the checkbox to set a hexadecimal number as a key for HEX encryption Keys for WEP encryption The access point uses the key selected from the Default Key ID drop down list It is required to specify all the fields Encryption Key WEP 1 4 You can specify keys containing 5 or 13 symbols use digits and or Latin characters If the Encryption Key WEP as HEX checkbox is selected you can specify only keys containing 10 symbols the digits 0 9 and the characters A F Page 97 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed value is selected the WPA Encryption settings section is displayed Security settings Network Authentication WPA2 PSK gt Encryption Key PSK 76543210 WPA2 Pre authentication T WPA Encryption settings WPA Encryption TKIP WPA reneval 3600 Figure 91 The WPA2 PSK value is selected from the Network Authentication drop down list Parameter Description Encryption Key PSK A key for WPA encryption The key can contain digits and or Latin characters The checkbox activating preliminary authentication displayed only for the WPA2 PSK and WPA PSK WPA2 PSK mixed authentication types WPA Encryption An encryption method TKIP AES or TKIP AES WPA2 Pre authent
59. WDS Additional settings WMM Client Hide Access Point SSID DAP 1150 Country RUSSIAN FEDERATION bd Channel 3 v Wireless mode 802 11 G only y When changing mode from B G on any of the modes with N is recommended to re tune security Max Associated Clients 0 Figure 113 Basic settings of the wireless LAN Parameter Description If the checkbox is selected other users cannot see your Wi Fi Hide Access Point network It is recommended not to select this checkbox in order to simplify initial configuration of your WLAN A name for the WLAN By default the value DAP 1150 is specified If your network is splitted into parts each part has the default name DAP 1150 2 DAP 1150 3 and DAP 1150 4 It is recommended to specify another name for the network upon initial configuration use digits and Latin characters The country you are in Select a value from the drop down list The wireless channel number When the auto value is selected the Channel ae access point itself chooses the channel with the least interference Operating mode of the wireless network of the access point This Wireless mode parameter defines standards of the devices that will be able to use your wireless network Select a value from the drop down list The maximum number of devices connected to the wireless network Max Associated Clients of the access point When the value 0 is specified the device does not limit the number of connecte
60. a 51 NDS ad E E ANA O E TE Gra I E Par os Sig wise han 0 Alek i DTE le A S EN E REL N a EEA 54 Addrtional Settings sarenim e a Beet e e A Sg e eae od hee Sod Seve ee dos 56 WMM eysens a eins TS DIAS ENE LES Seb SiG eee A AA TS E A Sel ie A E 58 Sea SE asine E SA E A AS oe 60 AVANCE A AA AA a heel a Raed 63 DS Vere SAMOA A DNA Tin a AS E A do ITA 63 Firewall eyi ee A A A A AA Grek ta E eS aA 64 MAC PDLLESE IA NS EI A A A A A di a A 64 SS CM A A A Pek A A A Se Pee ee lea 65 Administrator Passwords sed o do s alate a Sols SR 65 CONE PGUL At LOM s ren A a A A ial Be Sis lene di wide eee a wuenel se 66 System LOG eustera at A AA A A ela de a 67 Firmware Upgrade ad scorer seen a a o A A A eee Beane ASR 69 TSE ES VE AA SAT EA IES IE A A SALA 70 Chapter 5 Configuring Device Router Mode 71 Set p WIZATOAS mii A A AA AA A AA A AD AAA 71 ENESTNSE Setup Wizards sass ege sa a aR e Eas S E Gate Sete oe Sb Aa he ise eu doe E O 71 PER POP CONNECTION at A E A e EE EE e ios rea 73 Static ILE Connection y AA SAA AA AAA AS SAA Bee aoe 77 Dynami Cy PP CORN CC ELO A Aa as 80 PPTP ti Static LP or L2TP Statre TP CONNESCEDLON caseta a ela 82 PPEP Dynamic IP Or L2TB Dynamic TP Connections e ei ee A pie Ss 88 SES SETUP AWE Zar Ce A A A A ares cues ca ads cial 93 Wi Fi SOC WIZARD A e eligi a ete E aE EE EA 94 Sta Cus eee ot sn terete bs eect ae ge bs bee Pala Se eh AA A ij elt a a 100 Network SU Gite S Bi CS isi cha as S
61. age 171 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Telnet On the System Telnet page you can enable or disable access to the device settings via TELNET from your LAN By default access is enabled D Link DAP 1150 Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP dient Telnet Telnet On Port 23 System X Language X Figure 154 The System Telnet page To disable access via TELNET deselect the On checkbox and click the Change button To enable access via TELNET again select the On checkbox In the Port field enter the number of the access point s port through which access will be allowed by default the port 23 is specified Then click the Change button Page 172 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Operation Guidelines User Manual CHAPTER 6 OPERATION GUIDELINES Safety Instructions Place your access point on a flat horizontal surface or mount the access point on the wall the mounting holes are located on the bottom panel of the device Make sure that the access point is provided with sufficient ventilation To prevent overheating do not obstruct the ventilation openings of the access point Plug the access point into a surge protector to reduce the risk of damage from power surges and lightning strikes Operate the acc
62. all System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Filter mode MAC addresses MAC filter restrict mode Disabled Allow Deny Figure 43 The MAC filter for the wireless network By default MAC filtering is not active the Disabled choice of the MAC filter restrict mode radio button is selected To open your wireless network for the devices which MAC addresses are specified on the MAC addresses tab and to close the wireless network for all other devices select the Allow choice of the MAC filter restrict mode radio button and click the Change button To close your wireless network for the devices which MAC addresses are specified on the MAC addresses tab select the Deny choice of the MAC filter restrict mode radio button and click the Change button To add a MAC address to which the selected filtering mode will be applied proceed to the MAC addresses tab Page 48 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual D Link me o e DAP 1150 pr wi PR Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Filter mode MAC addresses MAC address adding MAC address lt Select address gt bod MAC address list MAC address Delete Delete Figure 44 The tab for adding a MAC address Enter an address in
63. an be applied only if the MSCHAP MACHAPv2 or AUTO value is selected from the Authentication algorithm drop down list Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value The maximum size of units transmitted by the interface Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive Keep Alive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the required values i Advanced options of the pppd daemon which need to be specified Extra options for this connection Optional Select the checkbox if you want the access point to establish connection to the Internet on demand In the Maximum idle time Dial on demand ee field specify a period of inactivity in seconds after which the connection should be terminated PPP debug Select the checkbox if you want to log all data on PPP connection debugging The IP address assigned by the ISP Page 121 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox if you want one WAN IP address to be used for Select the checkbox to enable protection against ARP and DDoS attacks all computers of your LAN
64. box to enable protection against ARP and DDoS attacks Without authorization Mm Password aan Password confirmation p VPN server address Encryption No encrypt x Authentication algorithm AUTO lt MTU 1456 Keep Alive E Extra options Dial on demand E PPP debug E Miscellaneous an Enable RIP NAT Y firewall Y Figure 105 The page for creating a new connection The VPN and Miscellaneous sections Parameter Description Select the checkbox to enable auto start of the connection upon the boot up of the access point Username A username login to access the Internet Select the checkbox if you don t need to enter a username and Without authorization password to access the Internet A password to access the Internet Password confirmation The confirmation of the entered password to avoid mistypes Page 115 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description VPN server address The IP or URL address of the PPTP or L2TP authentication server Select a method of MPPE encryption No encrypt MPPE encryption is not applied MPPE 40 128 bit MPPE encryption with a 40 bit or 128 bit key is applied Encryption MPPE 40 bit MPPE encryption with a 40 bit key is applied MPPE 128 bit MPPE encryption with a 128 bit key is applied MPPE encryption can be applied only if the MSCHAP
65. cated to the right of the relevant MAC address in the MAC address list section and click the Delete button Page 133 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Station List On the Wi Fi Station List page you can view the list of wireless clients connected to the access point Devices connected to the access point via the WDS function are not displayed in the list D Link e DAP 1150 Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client MAC AID PSM MIMOPS mos Bw SGI STBC EEE Figure 121 The list of the wireless clients If you want to disconnect a wireless device from your WLAN select the checkbox in the line containing the relevant MAC address and click the Disconnect button To view the latest data on the devices connected to the WLAN click the Refresh button Page 134 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual WPS On the Wi Fi WPS page you can enable the function for secure configuration of the WLAN and select a method used to easily add wireless devices to the WLAN The WPS function helps to configure the protected wireless network automatically Devices connecting to the wireless network via the WPS function must support the WPS function If the device s WLAN
66. cation type and devices using the WPA2 authentication type can connect to the WLAN of the access point A mixed type of authentication When this value is selected devices WPA PSK WPA2 PSK using the WPA PSK authentication type and devices using the mixed WPA2 PSK authentication type can connect to the WLAN of the access point The WPA WPA2 and WPA WPA2 mixed authentication types require a RADIUS m server Page 96 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the Open or Shared value is selected the WEP Encryption settings section is displayed the section is unavailable for the wireless network operating modes which support the standard 802 11n Security settings Network Authentication Open WEP Encryption settings Enable Encryption WEP Y Default Key ID Encryption Key WEP as HEX El Encryption Key WEP 1 Encryption Key WEP 2 Encryption Key WEP 3 Encryption Key WEP 4 Next gt Figure 90 The Open value is selected from the Network Authentication drop down list Parameter Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field the Encryption Key WEP as Enable Encryption WEP HEX checkbox and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected first to fourth which will f Default Key ID
67. cribes the access point DAP 1150 and explains how to configure and operate it This manual is intended for users familiar with basic networking concepts who create an in home local area network and system administrators who install and configure networks in offices Conventions Example Description text The body text of the manual Before You Begin A reference to a chapter or section of this manual Quick Installation Qu a A reference to a document Guide A name of a menu menu item control field checkbox drop down Change list button etc 192 168 0 50 Data that you should enter in the specified field I Information An important note Document Structure Chapter 1 describes the purpose and structure of the document Chapter 2 gives an overview of the device s hardware and software features describes its appearance and the package contents Chapter 3 explains how to install the DAP 1150 device and configure a PC in order to access its web based interface Chapter 4 describes all pages of the web based interface for the device in the access point mode Chapter 5 describes all pages of the web based interface for the device in the router mode Chapter 6 includes safety instructions and tips for networking Chapter 7 introduces abbreviations and acronyms used in this manual Page 5 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Overview User Manual CHAPTER 2 OVERVIEW General I
68. d clients When you have configured the parameters click the Change button Page 126 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Security Settings On the Wi Fi Security settings page you can modify security settings of the WLAN DAI ink System X Language v DAP 1150 paman i ns we ee Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Network Authentication Open WEP Encryption settings Enable Encryption WEP m Figure 114 The default security settings By default the Open network authentication type with no encryption is specified for the WLAN The default security settings do not provide sufficient protection for the WLAN Please specify your own security settings for the WLAN or each part of the WLAN if the network was splitted into parts Page 127 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Network Authentication WEP Encryption settings Enable Encryption WEP WPA PSK WPA2 PSK mixed Figure 115 Network authentication types supported by the access point The access point supports the following authentication types Authentication type Description Open authentication with WEP encryption for wireless network modes not supporting 802 11n devices Shared key authentication wit
69. ddress is specified 192 168 0 50 Press the Enter key File Edit View Bookmarks Widgets Tools Help lt a http 192 168 0 50 y Figure 15 Connecting to the web based interface of the DAP 1150 device On the opened page enter the username login and password for the administrator account by default the following username and password are specified admin admin Then click the Enter link D Link i o DAP 1150 Login admin Password Figure 16 The login page If the error The page cannot be displayed or Unable to display the page Could not connect to remote server occurs upon connecting to the web based interface of the access point make sure that you have properly connected the access point to your computer Page 25 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection Right after the first access to the web based interface you are forwarded to the page for changing the administrator password specified by default System password setting up The system password and the password for the web based interface will be changed at the same time Login admin Password Confirmation Save Figure 17 The page for changing the default administrator password Enter the new password in the Password and Confirmation fields Then click the Save button Remember or write down the new password for the administrator account In cas
70. dresses automatically checkbox and fill in the Primary DNS server and Secondary DNS server fields If your ISP has provided its identifier fill in the Vendor ID field Click the Next button to continue If needed change the connection settings available in the Miscellaneous section Internet connection wizard jp iris Enable RIP E Enable IGMP Multicast F NAT 7 firewall Y lt Back Next gt Figure 73 Configuring Dynamic IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox to allow multicast traffic from the external Enable IGMP Multi i i able IG ulticast network e g video streaming to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Click the Next button to continue After that the page displaying all specified settings opens Click the Save button to create the connection or the Back button to specify other settings After clicking the Save button the quick settings page opens Page 81 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual PPTP Static IP or L2TP Static IP Connection Internet connection wizard Connection name The connection name has been generated automatically according to the specified
71. e IP address of the gateway used by this WAN connection In the Primary DNS server and Secondary DNS server fields enter the addresses of the primary and secondary DNS servers Click the Next button to continue If needed enter the IP addresses of the ISP s local resources Internet connection wizard Routing configuration Here you can add IP addresses of your ISPS local resources Gick Add button to add resource Click mouse right button on the table header to add delete or edit addresses Destination network Destination netmask Add Edit Delete lt Back Next gt Figure 76 Configuring PPTP Static IP WAN connection To add a route click the Add button or right click the routing table heading and select the Add line from the shortcut menu displayed Click the Next button to continue Page 83 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual If needed change the connection settings available in the Miscellaneous section Internet connection wizard sr A A A snr ep sash a AE Enable RIP 7 Enable IGMP Multicast NAT firewall W lt Back Next gt Figure 77 Configuring PPTP Static IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox to allow multicast traffic from the external Enable IGMP Multicast network e g video stream
72. e Source last field If the IP address range checkbox is not selected specify the IP address of the host or subnet in the Source field To specify an IP address add 32 To choose a device connected to the access point s LAN at the moment select the relevant IP address from the drop down list located to the right of the field the field will be filled in automatically The destination host subnet IP address If the IP address range checkbox is selected specify the starting IP address of the range in the Destination first field and the ending IP address in the Destination last field If the IP address range checkbox is not selected specify the Destination starting IP address of the host or subnet in the Destination field To specify an IP address add 32 To choose a device connected to the access point s LAN at the moment select the relevant IP address from the drop down list located to the right of the field the field will be filled in automatically A port of the source IP address You can specify one port several ports separated by a comma or a range of ports separated by a colon A port of the destination IP address You can specify one port Destination several ports separated by a comma or a range of ports separated by a colon Click the Change button To edit a rule for IP filtering click the link to the relevant rule On the opened page change the needed parameters and click the Change button To r
73. e of losin the new password you can access the settings of the access point only after restoring the factory default settings via the hardware RESET button This procedure wipes out all settings that you have configured for your device After successful registration the access point s quick settings page opens When the device is switched to the access point mode the Configure Wi Fi Configure manually Logout buttons are available on the page You have connected to the web based interface of the DAP 1150 device now you can do the following O Configure Wi Fi Configure manually Figure 18 The quick settings page in the access point mode To configure the access point s wireless network click the Configure Wi Fi button After clicking the button the Wi Fi Setup Wizard opens see the Wi Fi Setup Wizard section page 31 To get back to the quick settings page from the Wi Fi Setup Wizard or any web based interface menu section left click the D Link logo in the top left corner of the page To configure all parameters of the access point independently without the Wizard click the Configure manually button Page 26 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection When the device is switched to the router mode the Connect to internet Host site Configure Wi Fi Configure manually and Logout buttons are available on the page You have connected to the w
74. eb based interface of the DAP 1150 device now you can do the following gt A Connect to internet Host site Configure Wi Fi Configure manually Figure 19 The quick settings page in the router mode To configure connection to the Internet click the Connect to internet button After clicking the button the Internet Setup Wizard opens see the Internet Setup Wizard section page 71 To configure access from the Internet to a web server located in your LAN click the Host site button After clicking the button the Site Setup Wizard opens see the Site Setup Wizard section page 93 To configure the access point s wireless network click the Configure Wi Fi button After clicking the button the Wi Fi Setup Wizard opens see the Wi Fi Setup Wizard section page 94 To get back to the quick settings page from any Wizard or web based interface menu section left click the D Link logo in the top left corner of the page To configure all parameters of the access point independently without the Wizards click the Configure manually button After clicking the Configure manually button the system statistics page opens The page displays general information on the access point and its software the version and the date of the firmware the IP address of the device the name of the WLAN etc Page 27 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection D Li Ki lo 4 Syste
75. ed The maximum size in bites of a non fragmented packet Larger Frag Threshold packets are fragmented divided The time period in seconds between sending a DTIM a message DTIM Period notifying on broadcast or multicast transmission and data transmission The transmit power in percentage terms of the access point Page 140 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description The 802 11b and 802 11g protection function is used to minimize collisions between devices of your wireless network Select a value from the drop down list Auto The protection function is enabled and disabled automatically depending on the state of the network this value is recommended if your wireless local area network consists of both 802 11b and 802 11g devices BG Protection Always On The protection function is always enabled this setting can substantially lower the efficiency of your wireless network Always Off The protection function is always disabled The channel bandwidth for 802 11n devices 20MHz 802 11n devices operate at 20MHz channels 40MHz 802 11n devices operate at 40MHz channels Bandwidth 20 40MHz 802 11n devices operate at 20MHz and 40MHz channels the channel is combined with the previous adjacent channel 20 40MHz 802 11n devices operate at 20MHz and 40MHz channels the channel is combined with the next adjacen
76. efault values The WMM function allows assigning priorities for four Access Categories AC AC_BK Background low priority traffic print jobs file downloads etc AC_BE Best Effort traffic from legacy devices or devices applications that do not support QoS AC_VI Video AC VO Voice Parameters of the Access Categories are defined for both the access point itself in the Parameters of Access Point section and wireless devices connected to it in the Parameters of Station section Page 142 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual For every Access Category the following fields are available Parameter Description Arbitrary Inter Frame Space Number This parameter influences Aifsn time delays for the relevant Access Category The lower the value the higher is the Access Category priority Contention Window Minimum Contention Window Maximum Both fields influence time delays for the relevant Access Category The CWMax field value should not be lower than the CWMin field value The lower the difference between the CWMax field value and the CWMin field value the higher is the Access Category CWMin CWMax priority Txo Transmission Opportunity The higher the value the higher is the P Access Category priority Admission Control Mandatory ACM If selected prevents from using the relevant Access Category Acknowledgmen
77. emand PPP IP extension Use Static IP Address PPP debug PPPoE pass through O Ofe g E Miscellaneous Enable RIP Enable IGMP Multicast NAT 7 firewall Y Figure 98 The page for creating a new connection The PPP and Miscellaneous sections Parameter Description Username A username login to access the Internet re Select the checkbox if you don t need to enter a username and Without authorization password to access the Internet A password to access the Internet Password confirmation The confirmation of the entered password to avoid mistypes The name of the PPPoE authentication server Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value The maximum size of units transmitted by the interface Page 105 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive Keep Alive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the required values Select the checkbox 1f you want the access point to establish connection to the Internet on demand In the Maximum idle time field specify a period of inactivity in seconds after which the con
78. emove a rule for IP filtering click the link to the relevant rule On the opened page click the Delete button Page 159 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Virtual Servers On the Firewall Virtual servers page you can create virtual servers for redirecting incoming Internet traffic to a specified IP address in the local area network D Link men osl men o DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System IP filters Virtual servers DMZ MAC filter Virtual servers list You can add edit and delete virtual servers here Name Interface Protocol Public port Private port Private IP Remote IP Figure 140 The Firewall Virtual servers page To create a new virtual server click the Add button D Link System X Language X DAP 1150 mE Firewall TP filters Virtual servers DMZ MAC filter Virtualserver settings y y y y y y y y yg yyy aaa Template a Name Interface dynamic WAN_1 v Protocol TP y Public port begin Public port end Private port begin Private port end Private IP lt Select address gt v Remote IP Change A d Figure 141 The page for adding a virtual server Page 160 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual You can specify the following parameters Parameter Description Select a virtual server templa
79. er Mode User Manual D Link A DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP Destination network Destination netmask Gateway Metric Via Interface lt Auto gt Figure 133 The page for adding a static route You can specify the following parameters Parameter Description Destination network A destination network to which this route is assigned Destination netmask The destination network mask An IP address through which the destination network can be accessed Gateway The filed is displayed when the lt Auto gt value is selected from the Via Interface drop down list A metric for the route The lower the value the higher is the route priority Optional Select an interface through which the destination network can be accessed from the drop down list If you have selected the lt Auto gt value of this drop down list the access point itself sets the interface on the basis of data on connected networks Via Interface Click the Save button To edit an existing route click the relevant route link On the opened page change the needed parameters and click the Save button To remove an existing route click the relevant route link On the opened page click the Delete button Page 152 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual Device mode On the Advanced
80. ernet port with auto MDI MDIX WLAN Interface IEEE 802 11b g n Operation Mode e Access point mode e Router mode Network Functions WAN connection types o PPPoE o Static IP o Dynamic IP o PPTP L2TP Static IP o PPTP L2TP Dynamic IP DHCP server and client DNS relay VPN pass through PPTP L2TP Dynamic DNS e Static IP routing Remote management e Network statistics for each interface IGMP Proxy e RIP e UPnP The device features are subject to change without notice For the latest versions of the firmware and relevant documentation visit www dlink ru Page 7 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Overview Wireless Connection WLAN splitting up to 4 SSIDs Supported security settings o WEP o WPA WPA2 Personal o WPA WPA2 Enterprise MAC filter Managing connected stations PIN and PBC methods of WPS WMM Wi Fi QoS Advanced settings WDS Client function access point mode o Wireless network client o Wireless network repeater Client function router mode o WISP repeater Firewall Functions Network Address Translation NAT Stateful Packet Inspection SPI IP filters URL filter MAC filter DMZ Prevention of ARP and DDoS attacks Virtual servers Page 8 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Overview Configuration and Management e Multilingual web based interface for c
81. ess Point Supporting Router Mode Installation and Connection User Manual When you keep the button pushed for more than 8 seconds the access point switches to I crash recovery mode To restore normal operation of the access point please contact the Technical Support Service When you have configured all needed settings click the Logout line Device Operation Modes Access Point Mode In the access point mode the device is used to create a wireless local area network or to connect to a wired router Router Mode In the router mode the device is used to connect devices equipped with a wireless interface to the Internet You can connect the device to a cable or DSL modem or to a private Ethernet line and create a WAN connection In addition you can configure connection to a Wireless Internet Service Provider When the device is switched to the router mode the LAN port is used as the WAN port al therefore you cannot connect to it via a wired connection Page 30 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Access Point Mode CHAPTER 4 CONFIGURING DEVICE ACCESS POINT MODE Setup Wizard Wi Fi Setup Wizard To specify all needed settings for your wireless network click the Configure Wi Fi button Common settings Enable Wireless 7 Advanced settings MBSSID Disabled v BSSID FO0 7D 68 8D 81 B2 v Figure 24 Common and advanced settings of the wire
82. ess of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Page 118 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ON Configuring Device Router Mode User Manual IP Obtain DNS server addresses automatically Vendor ID Miscellaneous Enable RIP Y Enable IGMP Multicast Y NAT Y firewall Y Figure 107 The page for creating a new connection The IP and Miscellaneous sections Parameter Description Obtain DNS server Select the checkbox to configure automatic assignment of DNS addresses server addresses If the checkbox is selected the Primary DNS automatically server and Secondary DNS server fields are not displayed Primary DNS server Enter addresses of the primary and secondary DNS servers in the Secondary DNS server relevant fields Vendor ID The identifier of your ISP Optional Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox to allow multicast traffic from the external network e g video streaming to be received Enable IGMP Multicast Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Page 119 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Confi
83. ess point only from an electrical outlet with the correct power source as indicated on the adapter Do not open the cover of the access point Otherwise any warranty will be invalidated Unplug the equipment before dusting and cleaning Use a damp cloth to clean the equipment Do not use liquid aerosol cleaners or magnetic static cleaning devices Wireless Installation Considerations The DAP 1150 device lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network Keep in mind however that the number thickness and location of walls ceilings or other objects that the wireless signals must pass through may limit the range Typical ranges vary depending on the types of materials and background RF noise in your home or office To maximize your wireless range follow the guidelines below 1 Keep the number of walls and ceilings between the DAP 1150 device and other network devices to a minimum each wall or ceiling can reduce your wireless network range by 3 90 feet 1 30 meters 2 Be aware of the direct line between network devices Place your devices so that the signal travels straight through a wall or ceiling instead of at an angle for better reception 3 Building materials make a difference A solid metal door or aluminum studs may have a negative effect on your wireless range Try to position your access point and wireless network devices so that the signa
84. esses in accordance with the specified pairs only when the DHCP server is enabled in the DHCP server section in the Mode drop down list the Enable value is selected Static DHCP lt Select IP MAC address gt Figure 34 The section for creating MAC IP pairs To create a MAC IP pair click the Add button Enter the MAC address of the device from the LAN in the MAC address field and an IP address which will be assigned to this device in the IP address field In the Host name field specify a network name of the device for easier identification optional Also you can create a MAC IP pair for a device connected to the access point s LAN at the moment To do this select the relevant value from the Known IP MAC addresses drop down list the IP address and MAC address fields will be filled in automatically When all needed MAC IP pairs are specified click the Save button Existing MAC IP pairs are displayed in the table of the Static DHCP section To remove a pair select the relevant line in the table and click the Remove button Then click the Save button Page 39 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual In the DHCP server section you can configure the built in DHCP sever of the access point DHCP server Mode Enable w Start IP 192 168 0 51 End IP 192 168 0 100 Lease time min 86400 Figure 35 The section for configuring the DHCP server
85. esses tab and to close the wireless network for all other devices select the Allow choice of the MAC filter restrict mode radio button and click the Change button To close your wireless network for the devices which MAC addresses are specified on the MAC addresses tab select the Deny choice of the MAC filter restrict mode radio button and click the Change button To add a MAC address to which the selected filtering mode will be applied proceed to the MAC addresses tab Page 132 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual DAI ink System X Language X DAP 1150 Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Filter mode MAC addresses MAC address adding MAC address lt Select address gt bd MAC address fist MAC address Delete Delete Figure 120 The tab for adding a MAC address Enter an address in the MAC address field of the MAC address adding section and click the Add button To add the MAC address of a device connected to the access point s LAN at the moment select the value containing the MAC and IP address of this device from the drop down list located to the right of the MAC address field the field will be filled in automatically and click the Add button To remove a MAC address from the list of MAC addresses select the checkbox lo
86. ettings Enable Encryption WEP Fl Figure 26 The default security settings The default security settings do not provide sufficient protection for the WLAN Please specify your own security settings for the WLAN or each part of the WLAN if the network was splitted into parts Page 32 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Security settings Network Authentication WEP Encryption settings WPA PSK WPA2 PSK mixed Figure 27 Network authentication types supported by the access point The access point supports the following authentication types Authentication type Description Open authentication with WEP encryption for wireless network modes not supporting 802 11n devices Shared key authentication with WEP encryption This authentication type is not available when on the basic settings page in the Wireless mode drop down list a mode supporting 802 11n devices is selected OO wW WPA based authentication using a RADIUS server 0 WPAPSK WPA based authentication using a PSK OO WR WPA2 based authentication using a RADIUS server WPA2PSK WPA2 based authentication using a PSK A mixed type of authentication When this value is selected devices WPA WPA2 mixed using the WPA authentication type and devices using the WPA2 authentication type can connect to the WLAN of the access point A mixed type of authentication When this
87. etwork authentication type with no encryption is specified for the WLAN Security settings Network Authentication WEP Encryption settings Enable Encryption WEP Figure 88 The default security settings The default security settings do not provide sufficient protection for the WLAN Please I specify your own security settings for the WLAN or each part of the WLAN if the network was splitted into parts Page 95 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Security settings Network Authentication WEP Encryption settings WPA WPA2 mixed WPA PSK WPA2 PSK mixed Figure 89 Network authentication types supported by the access point The access point supports the following authentication types Authentication type Description Open authentication with WEP encryption for wireless network modes not supporting 802 11n devices Shared key authentication with WEP encryption This authentication type is not available when on the basic settings page in the Wireless mode drop down list a mode supporting 802 11n devices is selected PA WPA based authentication using a RADIUS server O WPAPSK WPA based authentication using a PSK OO WR o WPA2 based authentication using a RADIUS server 0 WPA2PSK WPA2 based authentication using a PSK A mixed type of authentication When this value is selected devices WPA WPA2 mixed using the WPA authenti
88. evant service link On the opened page change the needed parameters and click the Change button To remove an existing DDNS service click the relevant service link On the opened page click the Delete button Page 149 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ON Configuring Device Router Mode User Manual DNS On the Advanced DNS page you can add DNS servers to the system D ink System X Language X DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP DNS settings Manual Default route 7 Change Figure 131 The Advanced DNS page DNS servers are used to determine the IP address from the name of a server in Intranets or the Internet as a rule they are specified by an ISP or assigned by a network administrator The device performs the DNS relay function i e it redirects the DNS requests of users to external DNS servers You can specify the addresses of DNS servers manually on this page or configure the access point to obtain DNS servers addresses automatically from your ISP upon installing a connection When you use the built in DHCP server the network parameters including DNS servers are distributed to clients automatically If you want to configure automatic obtainment of DNS servers addresses deselect the Manual checkbox select a WAN connection which will be used to obtain addresses of DNS servers automatically
89. evice Router Mode User Manual Creating Dynamic IP WAN Connection To create a connection of the Dynamic IP type click the Add button on the Net WAN page On the opened page select the Dynamic IP value from the Connection Type drop down list and specify the needed values General settings Connection Type Dynamic IP Port WAN v Name dynamic_WAN_2 Enable Y Direction WAN ee Ethemet j MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt v Figure 101 The page for creating a new connection The General settings and Ethernet sections Parameter Description General settings A physical interface to which the new connection will be assigned A name for connection for easier identification Select the checkbox to enable the connection The direction of this connection The maximum size of units transmitted by the interface Page 110 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Parameter Description A MAC address assigned to the interface This parameter is mandatory if your ISP uses MAC address binding In the field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment as the MAC address of the WAN interface Also you can set
90. filter On the opened page enter the MAC address of the device from the access point s LAN in the MAC address field To choose a device connected to the access point s LAN at the moment select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Then select the Deny value from the Action drop down list and click the Change button To remove an address from the list of MAC addresses for filtering select the line with the relevant MAC address On the opened page click the Delete button Page 64 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual System In this menu you can do the following e change the password used to access the access point s settings e save the current settings to the non volatile memory e create a backup of the access point s configuration e restore the access point s configuration from a previously saved file e restore the factory default settings e view the system log e update the firmware of the access point e allow or forbid access to the access point via TELNET Administrator Password On the System Administrator password page you can change the password for the administrator account used to access the web based interface of the access point and to access the device settings via TELNET I For security reasons it is strongly recommended to change the administrator passw
91. from the Interface drop down list or select the Default route checkbox so that the access point could use the connection set as the default gateway on the Net WAN page to obtain DNS server addresses and click the Change button If you want to specify the DNS server manually select the Manual checkbox and enter a DNS server address in the Name servers list To specify several addresses press the Enter key and enter a needed address in the next line Then click the Change button To remove a DNS server from the system remove the relevant line from the Name servers field and click the Change button Page 150 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Routing On the Advanced Routing page you can add static routes routes for networks that are not connected directly to the device but are available through the interfaces of the device into the system D Link DAP 1150 Start Status Net WiFi Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP Routing configuration inicios You can add edit and delete routes here Destination network Destination netmask Gateway System Via Interface Language v Accessibility Figure 132 The Advanced Routing page To create a new route click the Add button Page 151 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Rout
92. g in the MAC field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment Page 77 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Fill in the IP address and Netmask fields In the Gateway IP address field enter the IP address of the gateway used by this WAN connection In the Primary DNS server and Secondary DNS server fields enter the addresses of the primary and secondary DNS servers Click the Next button to continue If needed enter the IP addresses of the ISP s local resources Internet connection wizard Routing configuration Here you can add IP addresses of your ISPS local resources Gick Add button to add resource Click mouse right button on the table header to add delete or edit addresses Destination network Destination netmask Add ae Delete lt Back Next gt Figure 69 Configuring Static IP WAN connection To add a route click the Add button or right click the routing table heading and select the Add line
93. g to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS Firewall ba Click the Next button to continue After that the page displaying all specified settings opens Click the Save button to create the connection or the Back button to specify other settings After clicking the Save button the quick settings page opens Page 76 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Static IP Connection Internet connection wizard Connection name The connection name has been generated automaticaly according to the specified parameters You can specity another name or skip to the next step Name static_WAN_2 lt Back Next gt Figure 67 Configuring Static IP WAN connection In the Name field specify a name for the connection for easier identification and click the Next button Internet connection wizard E o y y O a MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt v O R IP Address Netmask Gateway IP address Primary DNS server Secondary DNS server Advanced IP settings lt Back Next gt Figure 68 Configuring Static IP WAN connection If needed in the MTU field change the maximum size of units transmitted by the interface If your ISP uses MAC address bindin
94. g Device mode Remote access IGMP Internet Group Management Protocol settings Enabled 7 Version 2 Change Figure 137 The Advanced IGMP page To enable IGMP select the Enabled checkbox From the Version drop down list select a version of IGMP Then click the Change button Such a setting allows using the IGMP Proxy function for all WAN connections for which the Enable IGMP Multicast checkbox is selected To disable IGMP deselect the Enabled checkbox and click the Change button Page 156 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual Firewall In this menu you can configure the firewall of the access point switched to the router mode e add rules for IP filtering e create virtual servers e define a DMZ e configure the MAC filter IP Filters On the Firewall IP filters page you can create new rules for filtering IP packets and edit or remove existing rules DAI ink System X Language DAP 1150 Net Wi Fi Advanced Firewall Control System IP filters Virtual servers DMZ MAC filter IP filters configuration IP address Port Name Protocol Source Destination Source Destination Figure 138 The Firewall IP filters page To create a new rule click the Add button Page 157 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual DAI ink System X Language X D
95. guring Device Router Mode User Manual VPN Connect automatically Username Without authorization Password e Password confirmation a VPN server address Encryption No encrypt gt Authentication algorithm AUTO y MTU 1456 Keep Alive E Extra options Dial on demand E PPP debug F IP received Miscellaneous Enable RIP F NAT 9 firewall Y Figure 108 The page for creating a new connection The VPN and Miscellaneous sections Parameter Description Select the checkbox to enable auto start of the connection upon the boot up of the access point Username A username login to access the Internet Select the checkbox if you don t need to enter a username and password to access the Internet A password to access the Internet Password confirmation The confirmation of the entered password to avoid mistypes VPN server address The IP or URL address of the PPTP or L2TP authentication server Without authorization Page 120 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description Select a method of MPPE encryption No encrypt MPPE encryption is not applied MPPE 40 128 bit MPPE encryption with a 40 bit or 128 bit key is applied Encryption MPPE 40 bit MPPE encryption with a 40 bit key is applied MPPE 128 bit MPPE encryption with a 128 bit key is applied MPPE encryption c
96. guring the WLAN are completed the specified settings are displayed on the page Check their correctness and then click the Save button After that you get to the quick settings page Page 36 of 175 DAP 1150 Wireless Access Point Supporting Router Mode A Configuring Device Access Point Mode User Manual Status The pages of this section display data on the current state of the access point e network statistics e data on devices connected to the access point s network and its web based interface Network Statistics On the Status Network statistics page you can view statistics for the local interface On the page the following data are displayed IP address subnet mask MAC address MTU value and volume of data received and transmitted with increase of the volume the units of measurement are changed automatically byte Kbyte Mbyte Gbyte X D Li ni 4 System X Language DAP 1150 Status Net Wi Fi Advanced Firewall System Network statistics LAN dients MAC MTU Rx Tx 1500 3 8351 Mbyte 18 644 Mbyte Name Type Status IP Mask Gateway LAN Up O 192 168 1 179 255 255 255 0 F0 7D 68 8D 81 B2 Figure 31 The Status Network statistics page Page 37 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual LAN Clients On the Status LAN clients page you can view the list of devices connected to the access point and devices acces
97. h WEP encryption This authentication type is not available when on the Wi Fi Basic settings page in the Wireless mode drop down list a mode supporting 802 11n devices is selected PA WPA based authentication using a RADIUS server o WPAPSK WPA based authentication using a PSK OO WR WPA2 based authentication using a RADIUS server 0 WPA2PSK WPA2 based authentication using a PSK A mixed type of authentication When this value is selected devices WPA WPA2 mixed using the WPA authentication type and devices using the WPA2 authentication type can connect to the WLAN of the access point A mixed type of authentication When this value is selected devices WPA PSK WPA2 PSK using the WPA PSK authentication type and devices using the mixed WPA2 PSK authentication type can connect to the WLAN of the access point if The WPA WPA2 and WPA WPA2 mixed authentication types require a RADIUS Mm server Page 128 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the Open or Shared value is selected the WEP Encryption settings section is displayed the section is unavailable for the wireless network operating modes which support the standard 802 11n Network Authentication Open WEP Encryption settings Enable Encryption WEP Y Default Key ID E E Encryption Key WEP as HEX Encryption Key WEP 1 Encryption Key WEP 2 Encryption Key WEP 3
98. he PIN value is selected from the WPS Method drop down list Click the button to connect the wireless device to the WLAN of the Connect SN f access point via the WPS function Page 52 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Access Point Mode To add a wireless device via the PIN method of the WPS function follow the next steps l 2 3 4 T Select the WPS Enable checkbox Click the Change button Select the PIN value from the WPS Method drop down list Select the PIN method in the software of the wireless device that you want to connect to the WLAN ofthe access point Click the relevant button in the software or on the cover of the wireless device that you want to connect to the WLAN Right after that enter the PIN code specified on the cover of the wireless device or in its software in the PIN Code field Click the Connect button in the web based interface of the access point To add a wireless device via the PBC method of the WPS function follow the next steps l 2 3 4 Select the WPS Enable checkbox Click the Change button Select the PBC value from the WPS Method drop down list Select the PBC method in the software of the wireless device that you want to connect to the WLAN ofthe access point Click the relevant button in the software or on the cover of the wireless device that you want to connect to the WLAN Click the Connect
99. he Username field enter your login and in the Password and Password confirmation fields the password provided by your ISP If authorization is not required select the Without authorization checkbox In the VPN server address field enter the IP or URL address of the PPTP or L2TP authentication server Page 90 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed specify additional settings for your PPTP Dynamic IP or L2TP Dynamic IP WAN connection Parameter Description Select a method of MPPE encryption No encrypt MPPE encryption is not applied MPPE 40 128 bit MPPE encryption with a 40 bit or 128 bit key is applied Encryption MPPE 40 bit MPPE encryption with a 40 bit key is applied MPPE 128 bit MPPE encryption with a 128 bit key is applied MPPE encryption can be applied only if the MSCHAP MACHAPv2 or AUTO value is selected from the Authentication algorithm drop down list Authentication Select a required authentication method from the drop down list or algorithm leave the AUTO value The maximum size of units transmitted by the interface Select the checkbox if you want the access point to keep you connected to your ISP even when the connection has been inactive Keep Alive for a specified period of time When the checkbox is selected the LCP interval and LCP fails fields are available Specify the required values i Advanced
100. he page for adding an address for the MAC filter On the opened page enter the MAC address of the device from the access point s LAN in the MAC address field To choose a device connected to the access point s LAN at the moment select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Then select the Deny value from the Action drop down list and click the Change button To remove an address from the list of MAC addresses for filtering select the line with the relevant MAC address On the opened page click the Delete button Page 163 of 175 DAP 1150 Wireless Access Point Supporting Router Mode a Configuring Device Router Mode User Manual Control This menu is designed to create restrictions on access to certain web sites URL Filter On the Control URL filter page you can specify restrictions on access to certain web sites D Li ni 4 System Language X DAP 1150 WiFi Advanced Firewall Control URL filter Configuration URL addresses URL filter configuration Enable Disable URL filter ial URL filter type Block listed URLs v Change Figure 145 The Control URL filter page The Configuration tab To enable the URL filter select the Enable Disable URL filter checkbox on the Configuration tab then select a needed mode from the URL filter type drop down list e Block listed URLs when this value is selected the access
101. he specified parameters You can specify another name or skip to the next step Name dynamic_WAN_2 lt Back Next gt Figure 71 Configuring Dynamic IP WAN connection In the Name field specify a name for the connection for easier identification and click the Next button Internet connection wizard SON inch A A A MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt v Clone MAC PE a E E E E A E EE A A casa Obtain DNS server addresses Y automatically Advanced IP settings jaaa Vendor ID lt Back Next gt Figure 72 Configuring Dynamic IP WAN connection If needed in the MTU field change the maximum size of units transmitted by the interface If your ISP uses MAC address binding in the MAC field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Page 80 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If your ISP has provided the addresses of the DNS servers deselect the Obtain DNS server ad
102. ication The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value O is specified for this field the key is not renewed Page 98 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual When the WPA WPA2 or WPA WPA2 mixed value is selected the RADIUS settings and WPA Encryption settings sections are available Security settings Network Authentication WPA2 WPA2 Pre authentication E RADIUS settings IP address 192 168 0 254 Port 1812 RADIUS encryption key dlink WPA Encryption settings WPA Encryption AES WPA reneval 3600 Figure 92 The WPA2 value is selected from the Network Authentication drop down list Parameter Description WPA2 Pre The checkbox activating preliminary authentication displayed only authentication for the WPA2 and WPA WPA2 mixed authentication types IP address The IP address of the RADIUS server Port A port of the RADIUS server The password which the access point uses for communication with RADIUS encryption key the RADIUS server the value of this parameter is specified in the RADIUS server settings An encryption method TKIP available only for the WPA WPA Encryption authentication type AES available only for the WPA2 and WPA WPA2 mixed authentication types The time period in seconds at the end of which a new key for WPA WPA renewal encryption is
103. ield specify a name for the connection for easier identification and click the Next button Internet connection wizard Beret O fC kO ja MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt v Clone MAC LT a EN EE NNE EE Obtain DNS server addresses Y automatically Advanced IP settings Vendor ID lt Back Next gt Figure 81 Configuring PPTP Dynamic IP WAN connection If needed in the MTU field change the maximum size of units transmitted by the interface If your ISP uses MAC address binding in the MAC field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Page 88 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If your ISP has provided the addresses of the DNS servers deselect the Obtain DNS server addresses automatically checkbox and fill in the Primary DNS server and Secondary DNS server fields If your ISP has provided its identifier fill in the Vendor ID field Click the Next button to continue
104. igure advanced settings of the access point switched to the router mode e enable the UPnP function e configure a DDNS service e add name servers e define static routes e switch the device to the other mode e create rules for remote access to the web based interface e allow the access point to use IGMP UPnP On the Advanced UPnP page you can enable the UPnP function UPnP is a set of networking protocols designed for automatic configuration of network devices The UPnP function performs automatic configuration of the device s parameters for network applications requiring an incoming connection to the access point D Link a DAP 1150 Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP UPnP settings Enabled Change Figure 128 The Advanced UPnP page If you want to manually specify all parameters needed for network applications deselect the Enabled checkbox and click the Change button If you want to enable the UPnP function in the access point select the Enabled checkbox select an interface for which the device s parameters will be automatically configured from the Interface drop down list and click the Change button Page 147 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode DDNS On the Advanced DDNS page you can define parameters of the DDNS service which allows associating a domain name wi
105. ing to be received Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Click the Next button to continue Page 84 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Internet connection wizard A reci econo rea Connect automatically 7 Username Without authorization T Password en Password confirmation VPN server address Advanced PPP settings Encryption No encrypt v Authentication algorithm AUTO X MTU 1456 Keep Alive F Extra options Dial on demand F PPP debug F IP received lt Back Next gt Figure 78 Configuring PPTP Static IP WAN connection Leave the Connect automatically checkbox selected to allow automatic start of the connection upon the load of the access point In the Username field enter your login and in the Password and Password confirmation fields the password provided by your ISP If authorization is not required select the Without authorization checkbox In the VPN server address field enter the IP or URL address of the PPTP or L2TP authentication server Page 85 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed specify additional settings for your PPTP Static IP or L2TP Static
106. l passes through drywalls or open doorways Materials and objects such as glass steel metal walls with insulation water fish tanks mirrors file cabinets brick and concrete will degrade your wireless signal 4 Keep your access point away at least 3 6 feet or 1 2 meters from electrical devices or appliances that generate RF noise 5 If you are using 2 4 GHz cordless phones or X 10 equipment wireless devices such as ceiling fans lights and home security systems your wireless connection may degrade dramatically or drop completely Make sure your 2 4 GHz phone base is as far away from your wireless devices as possible Note that the base transmits a signal even if the phone in not 1n use Page 173 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Abbreviations and Acronyms CHAPTER 7 ABBREVIATIONS AND ACRONYMS AC Access Category AES Advanced Encryption Standard ARP Address Resolution Protocol BSSID Basic Service Set Identifier CCK Complementary Code Keying CRC Cyclic Redundancy Check DDNS Dynamic Domain Name System DDoS Distributed Denial of Service DHCP Dynamic Host Configuration Protocol DMZ DeMilitarized Zone DNS Domain Name System DTIM Delivery Traffic Indication Message GMT Greenwich Mean Time HTMIX High Throughput Mixed IGMP Internet Group Management Protocol IP Internet Protocol ISP Internet
107. lds are not displayed Logging type Remote the system log is sent to the remote host specified in the Server field Local and remote the system log is stored in the device s memory and displayed on the Log tab and sent to the remote host specified in the Server field Logging level Select a type of messages and alerts notifications to be logged From the drop down list select the IP value to specify an IP address Server address type of a host from the local or global network or the URL value to specify a URL address of a remote server The IP or URL address of the host from the local or global network Server to which the system log will be sent A port of the host specified in the Server field By default the P i or value 514 is specified Page 168 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual After specifying the needed parameters click the Change button To disable logging of the system events deselect the Logging checkbox and click the Change button On the Log tab the events specified in the Logging level list are displayed D Link Seen Le DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP dient Telnet Confiauration Log Jan 106 08 50 syslogd started BusyBox v1 19 2 Refresh Export Figure 151 The System System l
108. less LAN On the opened page in the Common settings section select the Enable Wireless checkbox if it was deselected before to enable Wi Fi connections In the Advanced settings section you can split your network into several parts To do this select the relevant value 2 3 or 4 from the MBSSID drop down list Click the Next button to continue Page 31 of 175 DAP 1150 Wireless Access Point Supporting Router Mode A Configuring Device Access Point Mode User Manual In the Basic settings section you can change the basic parameters of your access point s WLAN hide your wireless network Hide Access Point specify a name for the network SSID select your location Country and the wireless channel number Channel specify the operating mode Wireless Mode and the maximum number of devices connected to the wireless network Max Associated Clients Basic settings Hide Access Point SSID DAP 1150 Country RUSSIAN FEDERATION ad Channel 13 Ov Wireless mode 802 11 G only y When changing mode from B G on any of the modes with N is recommended to re tune security Max Associated Clients 0 Figure 25 Basic settings of the wireless LAN Click the Next button to continue On the next page you can modify security settings of the WLAN By default the Open network authentication type with no encryption is specified for the WLAN Security settings Network Authentication WEP Encryption s
109. lick the Save button Page 112 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Creating PPTP Static IP or L2TP Static IP WAN Connection To create a connection of the PPTP Static IP or L2TP Static IP type click the Add button on the Net WAN page On the opened page select the relevant value from the Connection Type drop down list and specify the needed values General settings Connection Type PPTP StaticIP y Port WAN vw Name statpptp_WAN_2 Enable 7 Direction WAN sea Ethemet ee MTU 1500 MAC FO 7D 68 8D 81 B2 lt Selectaddress gt v Figure 103 The page for creating a new connection The General settings and Ethernet sections Parameter Description General settings A physical interface to which the new connection will be assigned A name for connection for easier identification Select the checkbox to enable the connection The direction of this connection MTU The maximum size of units transmitted by the interface Page 113 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description A MAC address assigned to the interface This parameter is mandatory if your ISP uses MAC address binding In the field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of
110. m v Language DAP 1150 Start Status Net WiFi Advanced Firewall System Device information Model DAP 1150 Firmware version 1 3 0 Build time Mon Dec 19 14 54 07 MSK 2011 Vendor D Link Russia Support support dlink ru Summary Root filesystem image for DAP 1150 Web revision 5d64b5aa23f1b1dfa4347f4b9afed2efd88cdedd LAN IP 192 168 1 179 LAN MAC F0 7D 68 8D 81 82 SSID DAP 1150 Figure 20 The system statistics page From the system statistics page you can proceed to the page for upgrading the access point s firmware contact the technical support group and proceed to the settings of the local interface or the device s WLAN To upgrade the firmware of the access point left click the current firmware version the right column of the Firmware version line After clicking the line the System Firmware upgrade page opens see the Firmware Upgrade section page 69 To contact the technical support group to send an e mail left click the support e mail address the right column of the Support line After clicking the line the e mail client window for sending a new letter to the specified address opens To edit the access point s local interface parameters left click the IP or MAC address of the local interface the right column of the LAN IP line or LAN MAC line correspondingly After clicking the line the page for editing the LAN interface opens see the LAN section page 39 To configure the access
111. matically in OS Windows 7 l Click the Start button and proceed to the Control Panel window 2 Select the Network and Sharing Center section If the Control Panel has the category view the Category value is selected from the View by drop down list in the top right corner of the window choose the View network status and tasks line under the Network and Internet section CO gt Control Panel All Control Panel Items v 49 Search Control Panel Pp pa Eon Adjust your computer s settings 0 Ee a Indexing Options Internet Options Location and Other Mouse Sensors Notification Area Icons Parental Controls Personalization Phone and Modem ORRORE Programs and Features Recovery RemoteApp and Desktop ca a Connections Sync Center Ba System Troubleshooting E User Accounts Windows Defender Pg Windows Firewall O o on y ap View by Large icons Y Keyboard Network and Sharing Center Performance Information and Tools Power Options A Region and Language Speech Recognition m Taskbar and Start Menu Windows CardSpace Windows Update Figure 6 The Control Panel window Page 17 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection 3 In the menu located on the left part of the window select the Change adapter settings line 9 ES gt Control Panel Network and Inte
112. name has been generated automatically according to the specified parameters You can specify another name or skip to the next step Name pppoe WAN _2 lt Back Next gt Figure 63 Configuring PPPoE WAN connection In the Name field specify a name for the connection for easier identification and click the Next button Internet connection wizard A O Cf C kO jyjlaaaaaaa MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt v Clone MAC a a S Username Without authorization F Password dui Password confirmation paa Advanced PPP settings lt Back Next gt Figure 64 Configuring PPPoE WAN connection If needed in the MTU field change the maximum size of units transmitted by the interface If your ISP uses MAC address binding in the MAC field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Page 73 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual In the Username field enter your login and in the
113. nection should be terminated PPP IP extension This option is used by some ISPs Contact your ISP to clarify if this checkbox needs to be enabled Select the checkbox if you want to use a static IP address to access Use Static IP Address the Internet In the IP Address field displayed when the checkbox is selected specify a static IP address PPP debu Select the checkbox if you want to log all data on PPP connection 2 debugging Select the checkbox if you want to allow PPPoE clients of PPPoE pass through computers from your LAN to connect to the Internet through this PPPoE connection of the access point lect the check to all lticast traffic fi th ternal Enable IGMP Multicast Select the c ec box to allow multicast traffic from the externa network e g video streaming to be received Enable RIP Select the checkbox to allow using RIP for this connection lect the check to all lticast traffic fi th ternal Enable IGMP Multicast Select the c ec box to al ow mu icast raffic from the externa network e g video streaming to be received NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Dial on demand Firewall When all needed settings are configured click the Save button Page 106 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Creati
114. nformation The DAP 1150 device is a wireless access point supporting the router mode It is an affordable solution for creating wireless networks at home or in an office Using DAP 1150 you are able to quickly create a wireless network and let your relatives or employees connect to it virtually anywhere within the operational range of your wireless network The access point can operate as a base station for connecting wireless devices of the standards 802 11b 802 11g and 802 11n at the rate up to 150Mbps The device supports multiple functions for the wireless interface several security standards WEP WPA WPA2 MAC address filtering WPS WDS WMM You are able to connect the wireless access point DAP 1150 switched to the router mode to a cable or DSL modem or to a private Ethernet line and use a high speed Internet connection to successfully fulfill a wide range of professional tasks In the router mode the DAP 1150 device includes a built in firewall The advanced security functions minimize threats of hacker attacks prevent unwanted intrusions to your network and block access to unwanted websites for users of your LAN You can configure and manage the settings of the DAP 1150 device via the user friendly web based interface the interface is available in several languages Page 6 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Overview Specifications LAN Interface 1 10 100BASE TX Eth
115. ng Static IP WAN Connection To create a connection of the Static IP type click the Add button on the Net WAN page On the opened page select the Static IP value from the Connection Type drop down list and specify the needed values SA at Connection Type Static IP gt Port WAN v Name static_WAN_2 Enable Y Direction WAN Ethemet ce MTU 1500 MAC FO 7D 68 8D 81 B2 lt Select address gt v Figure 99 The page for creating a new connection The General settings and Ethernet sections Parameter Description General settings A physical interface to which the new connection will be assigned A name for connection for easier identification Select the checkbox to enable the connection The direction of this connection OO MU The maximum size of units transmitted by the interface Page 107 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description A MAC address assigned to the interface This parameter is mandatory if your ISP uses MAC address binding In the field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment as the MAC address of the WAN interface Also you can set the address of a device connected to the access point s L
116. ngs Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client WDS Mode Bridge mode v WDS Phy Mode TK WDS Encryption NONE WDS MAC 1 WDS MAC 2 WDS MAC 3 WDS MAC 4 Figure 123 The page for configuring the WDS function Page 138 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual The following fields are available on the page Parameter Description The WDS function mode Disable The function is disabled Bridge mode Access points communicate to each other only WDS Mode wireless devices cannot connect to them Repeater mode Access points communicate to each other wireless clients can connect to the WLAN created by interconnected access points A physical mode of data transfer between access points interconnected via the WDS function CCK 802 11b devices only WDS Phy M a OFDM 802 11g devices only HTMIX 802 11g and 802 11n devices GREENFIELD 802 11n devices only A type of encryption for data transfer between access points interconnected via the WDS function NONE No encryption WEP TKIP AES A key for the specified type of encryption If the NONE value is Encryption Key selected from the WDS Encryption drop down list the field is not displayed WDS MAC 1 4 The MAC addresses of devices connected to the access point via the WDS function The WDS function parameters specified on
117. nication with RADIUS encryption key the RADIUS server the value of this parameter is specified in the RADIUS server settings An encryption method TKIP available only for the WPA WPA Encryption authentication type AES available only for the WPA2 and WPA WPA2 mixed authentication types The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field the key is not renewed When you have configured the parameters click the Change button Page 131 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual MAC Filter On the Wi Fi MAC Filter page you can define a set of MAC addresses of devices which will be allowed to access the WLAN or define MAC addresses of devices which will not be allowed to access the WLAN D Link Sein Le o gt DAP 1150 pann anaana nian Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Filter mode MAC addresses MAC filter restrict mode Disabled Allow Deny Change Figure 119 MAC filters for the wireless network By default MAC filtering is not active the Disabled choice of the MAC filter restrict mode radio button is selected To open your wireless network for the devices which MAC addresses are specified on the MAC addr
118. nt Supporting Router Mode Configuring Device Access Point Mode User Manual Network Authentication WEP Encryption settings Enable Encryption WEP WPA PSK WPA2 PSK mixed Figure 39 Network authentication types supported by the access point The access point supports the following authentication types Authentication type Description Open authentication with WEP encryption for wireless network modes not supporting 802 11n devices Shared key authentication with WEP encryption This authentication type is not available when on the Wi Fi Basic settings page in the Wireless mode drop down list a mode supporting 802 11n devices is selected PA WPA based authentication using a RADIUS server o WPAPSK WPA based authentication using a PSK OO WR WPA2 based authentication using a RADIUS server 0 WPA2PSK WPA2 based authentication using a PSK A mixed type of authentication When this value is selected devices WPA WPA2 mixed using the WPA authentication type and devices using the WPA2 authentication type can connect to the WLAN of the access point A mixed type of authentication When this value is selected devices WPA PSK WPA2 PSK using the WPA PSK authentication type and devices using the mixed WPA2 PSK authentication type can connect to the WLAN of the access point if The WPA WPA2 and WPA WPA2 mixed authentication types require a RADIUS Mm server Page 44 of 175 DAP 1150 Wireless Access Poin
119. ntrguring Wi Fi Adapter In OS Windows MPs ws iio eek ee he A Ee i a 22 Configuring Wi Fi Adapter an OS WindOws Dista aa ae ace eae eed teen ee a 23 Connecting to Web based Interface oooooooooccococoooooo ooo o ooo 25 Saving and Restoring SettingGS o ooooooooooocococco o ee ee ee ooo 29 Device Operation Modes os o sataa Sle Ee e Be SUNT ee Soe ee ee eee 30 ACCESS POUT MOLE ered See A a OE eo anise Sie dd Bee Rw el ete bes 30 ROUGE MO di eed A Bids ei eee lO Sy a Renee Sw ee GEER EE a eee 30 Chapter 4 Configuring Device Access Point Mode 31 SETUP WU ZA dacti wlohe apa chee a Belang ee BE a Se yee a Gusta ee Glee 31 WAS EL GEC Up Wizard i088 a o dd A O a aE A S 31 Status foe ieee ee Beale oh est ee tues Ow See SN eee eae aie DAE ALES taal 37 Network Sta liS Gl CS A Sica eaten PD E EA eke shee iS 37 DAN 2CVVentss jc tS ook A eae aie bee Boda Sele SRS Sh ane Ca Sos Bee ee ae 38 NEE Aae a E aa a ara a e a an aaa Ta a rE a Bulg Sah een avia aa Oy eh RR O 39 BAN A A AA ATA A A EE E E O A 39 Page 2 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual WISER ise tt ohn SE AE NA Stor Bees as Gea id Beaded 41 Common settings SA A E tate A A A a aaa 41 Bas TO S t tings sew A war A le AAA AAA a walle 42 SECCURDEY Settings A A A A A ia ral 43 MAC RT DST as sl co oa AAA e E AA e a a oa 48 Statron LLST A A RS E A A AI E A te 50 MBE a A NA TAO AS A la o
120. og page The Log tab To view the latest system events click the Refresh button To save the system log to your PC click the Export button and follow the dialog box appeared Page 169 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode Firmware Upgrade On the System Firmware upgrade page you can upgrade the firmware of the access point y Upgrade the firmware only when the access point is connected to your PC via a wired a connection available only in the access point mode D Link A DAP 1150 Start Status Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP dient Telnet Select update file Choose Update Figure 152 The System Firmware upgrade page The current version of the device s firmware is displayed in the Firmware version field on the Start page If you need to install a newer version of the firmware follow the next steps Attention Do not turn off the access point before the firmware upgrade is completed a This may cause the device breakdown 1 Download a new version of the firmware from www dlink ru 2 Click the Choose Browse button on the System Firmware upgrade page to locate the new firmware file Click the Update button to upgrade the firmware of the access point Wait until the access point is rebooted about one and a half or two minutes
121. ogout Start Status Net WiFi Advanced Firewall System Figure 23 The top page menu Click the Reboot line if you have already saved the device s settings Click the Save amp Reboot line to save new settings and immediately reboot the access point Click the Save line to save new settings to the non volatile memory and continue configuring the device Also you can save the device s parameters via the Save button on the System Configuration page Click the Backup line and follow the dialog box appeared to save the configuration all settings of the access point to your PC Also you can save the device s configuration to your PC via the Backup button on the System Configuration page Click the Factory line to restore the factory default settings Also you can restore the factory defaults via the Factory button on the System Configuration page Also you can restore the factory default settings via the hardware RESET button The button is located on the back panel of the access point next to the power connector To restore the factory default settings do the following 1 Power off the device 2 Insert a small paperclip into the hole of the RESET button and push 3 Power on the device keeping the button pushed 4 After 5 seconds release the button Wait for about 30 seconds Now you can access the web based interface of the access point using the default IP address username and password Page 29 of 175 DAP 1150 Wireless Acc
122. onfiguration and management e Access via TELNET e Firmware update via web based interface e Saving restoring configuration to from file Support of remote logging e Automatic synchronization of system time with NTP server router mode e Power e LAN WAN e WLAN Power External power adapter DC 5V 1 2A RESET to Factory Defaults button Operating Temperature from 0 to 55 C from 32 to 131 F Operating Humidity e from 10 to 90 non condensing Certification CE FCC Class B e C Tick e Wi Fi Page 9 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Overview User Manual Product Appearance Front Panel DAP 1150 Figure 1 Front panel view Mode Description Solid green The device is powered on No light The device is powered off When powered on the device is being loaded when Solid yellow loaded a malfunction of the device Access point mode the device has an IP address and is Solid green available for configuration Router mode a WAN connection is established Blinking green The port is active upstream or downstream traffic LAN WAN When powered on the device is being loaded when Solid yellow loaded in the router mode no WAN connection is established 3 The device s WLAN is on S MER The WLAN interface is active upstream or Blinking green downstream traffic Page 10 of 175 DAP 1150 Wireless Access Point Supporting Router Mode U
123. options of the pppd daemon which need to be specified Extra options for this connection Optional Select the checkbox if you want the access point to establish connection to the Internet on demand In the Maximum idle time Dial on demand EE aes field specify a period of inactivity in seconds after which the connection should be terminated PPP debug Select the checkbox if you want to log all data on PPP connection debugging The IP address assigned by the ISP Click the Next button to continue Page 91 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed change the settings of the VPN tunnel available in the Miscellaneous section Internet connection wizard Miscellaneous Additional settings of VPN tunnel Enable RIP El NAT 2 firewall Y lt Back Next gt Figure 84 Configuring PPTP Dynamic IP WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox if you want one WAN IP address to be used for NAT all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks Click the Next button to continue After that the page displaying all specified settings opens Click the Save button to create the connection or the Back button to specify other settings After clicking the Save button the q
124. ord upon initial configuration of the access point D Li i iM 4 System X Language X DAP 1150 Start Status Net Wi Fi Advanced Firewall System Administrator password Configuration System log Firmware upgrade Telnet System password setting up The system password and the password for the web based interface wil be changed at the same time Login admin v Password Confirmation Save Figure 55 The page for modifying the administrator password Enter the new password in the Password and Confirmation fields and click the Save button Page 65 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Configuration On the System Configuration page you can save the changed settings to the non volatile memory restore the factory defaults backup the current configuration or restore the device s configuration from a previously created file D Li ni 4 System X Language X DAP 1150 IN System Administrator password Configuration System log Firmware upgrade Telnet Save current settings Reset to factory defaults Saving current configuration in a file Backup Loading previously saved configuration to Choose Restore device Figure 56 The System Configuration page The following buttons are available on the page Control Description Click the button to save settings to the non volatile memory Please sa
125. ort of your PC Connect the power cord to the power connector port on the back panel of the access point then plug the power adapter into an electrical outlet or power strip Turn on your PC and wait until your operating system is completely loaded Obtaining IP Address Automatically in OS Windows XP l Click the Start button and proceed to the Control Panel gt Network and Internet Connections gt Network Connections window In the Network Connections window right click the relevant Local Area Connection icon and select the Properties line in the menu displayed Network Connections File Edit View Favorites Tools Advanced Help Q sak gt O ya Search Key Folders EEE Address 43 Network Connections Name Type Status Network Tasks LAN or High Speed Internet Other Places BEL ocal Area Connection jig ae or High Speed Inter Enabled Status Repair G Control Panel my Network Places E My Documents Bridge Connections Create Shortcut Rename Figure 3 The Network Connections window Details Page 14 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Installation and Connection User Manual 3 In the Local Area Connection Properties window on the General tab select the Internet Protocol TCP IP line Click the Properties button 4 Local Area Connection 2 Properties EJES General Authentication Advanced Connect using E D Link DFE 550TX
126. ously saved configuration all settings of the access point from a file on your PC Click the Restore 3 Choose Browse button to select a previously saved configuration file located on your PC Actions of the Save Factory and Backup buttons also can be performed via the top page menu displayed when the mouse pointer is over the System caption 3 The name ofthe button depends upon the web browser that you use Page 167 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual System Log On the System System log page you can set the system log options and configure sending the system log to a remote host DAI ink System X Language v DAP 1150 Net Wi Fi Advanced Firewall Control System Administrator password Configuration System log Firmware upgrade NTP dient Telnet Configuration Log Logging Ea Logging type Local and remote v Logging level Informational messages v Server address type P v Server Port 514 Figure 150 The System System log page The Configuration tab To enable logging of the system events select the Logging checkbox on the Configuration tab Then specify the needed parameters Control Description Select a type of logging from the drop down list e Local the system log is stored in the device s memory and displayed on the Log tab When this value is selected the Server address type Server and Port fie
127. parameters You can specify another name or skip to the next step Name statpptp WAN_2 lt Back Next gt Figure 74 Configuring PPTP Static IP WAN connection In the Name field specify a name for the connection for easier identification and click the Next button Internet connection wizard ec E a RE ETE Te ED MTU 1500 MAC F0 7D 68 8D 81 B2 lt Select address gt E a PEE A A A A A A A r e AR IP Address Netmask Gateway IP address Primary DNS server Secondary DNS server Advanced IP settings lt Back Next gt Figure 75 Configuring PPTP Static IP WAN connection If needed in the MTU field change the maximum size of units transmitted by the interface If your ISP uses MAC address binding in the MAC field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment Page 82 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Also you can set the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Fill in the IP address and Netmask fields In the Gateway IP address field enter th
128. point blocks access to all addresses specified on the URL addresses tab Block all URLs except listed when this value is selected the access point allows access to addresses specified on the URL addresses tab and blocks access to all other web sites Click the Change button To specify URL addresses to which the selected filtering will be applied go to the URL addresses tab and click the Add button Page 164 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Configuring Device Router Mode D ink System v Language DAP 1150 Start Status Net WiFi Advanced Firewall Control URL filter Configuration URL addresses URL addresses list You can add edit and delete addresses here URL address Figure 146 The Control URL filter page The URL addresses tab On the opened page specify the needed parameters 2 gt stem X anguage D Link ze DAP 1150 Start Status Net WiFi Advanced Firewall Control URL filter Configuration URL addresses URL address editing URL address Figure 147 The page for adding an address for the URL filter Enter a URL address in the URL address field and click the Save button To remove an address from the list of URL addresses select the relevant address in the table on the URL addresses tab and click the Delete button To disable the URL filter deselect the Enable Disable URL filter checkbox on the Configuration tab then click the Change
129. r Latin characters When you have configured the parameters click the Change button In addition when the Enable client checkbox is selected the list of available wireless networks is displayed on the page The Unknown wireless networks field shows the number of hidden wireless networks To view the latest data on the available wireless networks click the Search button To connect to a wireless network from the list select the needed network Upon that the relevant values are automatically inserted in the SSID BSSID and Network Authentication fields For the Open authentication type with no encryption click the Change button For the Open authentication type with encryption and the Shared authentication type select a needed value from the Default Key ID drop down list fill in 4 Encryption Key WEP fields and click the Change button For the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed authentication types fill in the Encryption Key PSK field and click the Change button After clicking the Change button the wireless channel of DAP 1150 will switch to the channel of the wireless access point to which you have connected If the access point is connected to the selected network successfully the green indicator appears to the right of the network s SSID in the table Page 146 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Advanced In this menu you can conf
130. ration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Use the Following IP address Obtain DNS server address automatically Use the Following DNS server addresses Validate settings upon exit Advanced Figure 10 The Internet Protocol Version 4 TCP IPv4 Properties window 7 Click the OK button in the connection properties window Now your computer is configured to obtain an IP address automatically PC with Wi Fi Adapter 1 Connect the power cord to the power connector port on the back panel of the access point then plug the power adapter into an electrical outlet or power strip 2 Turn on your PC and wait until your operating system is completely loaded 3 Turn on your Wi Fi adapter As a rule modern notebooks with built in wireless NICs are equipped with a button or switch that turns on off the wireless adapter refer to your PC documents If your PC is equipped with a pluggable wireless NIC install the software provided with your Wi Fi adapter Page 21 of 175 DAP 1150 Wireless Access Point Supporting Router Mode g Installation and Connection User Manual Configuring Wi Fi Adapter in OS Windows XP 1 Click the Start button and proceed to the Control Panel gt Network and Internet Connections gt Network Connections window 2 Select the icon of the
131. rd in the Password and Confirmation fields and click the Save button Page 166 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Configuration On the System Configuration page you can save the changed settings to the non volatile memory restore the factory defaults backup the current configuration or restore the device s configuration from a previously created file DAI ink System y Language v DAP 1150 ri N System Administrator password Configuration System log Firmware upgrade NTP dient Telnet Save current settings Reset to factory defaults Factory Saving current configuration in a file Loading previously saved configuration to Restore device Figure 149 The System Configuration page The following buttons are available on the page Control Description Click the button to save settings to the non volatile memory Please save settings every time you change the device s parameters Save Otherwise the changes will be lost upon hardware reboot of the access point Click the button to restore the factory default settings Also you can Factory restore the factory defaults via the hardware RESET button see the Saving and Restoring Settings section page 29 Backu Click the button and follow the dialog box appeared to save the P configuration all settings of the access point to your PC Click the button to upload a previ
132. required values Select the checkbox if you want the access point to establish connection to the Internet on demand In the Maximum idle time field specify a period of inactivity in seconds after which the connection should be terminated This option is used by some ISPs Contact your ISP to clarify if this checkbox needs to be enabled Select the checkbox if you want to use a static IP address to access the Internet In the IP Address field displayed when the checkbox 1s selected specify a static IP address Select the checkbox if you want to log all data on PPP connection debugging Select the checkbox if you want to allow PPPoE clients of computers from your LAN to connect to the Internet through this PPPoE connection of the access point Click the Next button to continue Page 75 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual If needed change the connection settings available in the Miscellaneous section Internet connection wizard Mi A NA Enable RIP E Enable IGMP Multicast E NAT 2 firewall Y lt Back Next gt Figure 66 Configuring PPPoE WAN connection Parameter Description Enable RIP Select the checkbox to allow using RIP for this connection lect the check to all Iticast traffic fi th ternal Enable IGMP Multicast Select the checkbox to allow multicast traffic from the externa network e g video streamin
133. rnet Network and Sharing Center X Search Control Panel p m Control Panel Home View your basic network information and set up connections Manage wireless networks ww gt Q See full map cl Change adapter settings as Change advanced sharing This computer settings View your active networks Connect to a network You are currently not connected to any networks Change your networking settings lt Set up a new connection or network Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or access point Connect to a network Connect or reconnect to a wireless wired dial up or VPN network connection Choose homegroup and sharing options Access files and printers located on other network computers or change sharing settings See also Troubleshoot problems HomeGroup Diagnose and repair network problems or get troubleshooting information Internet Options Windows Firewall Figure 7 The Network and Sharing Center window Page 18 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection 4 In the opened window right click the relevant Local Area Connection icon and select the Properties line in the menu displayed lal ee xX te B gt Control Panel Network and Internet Network Connections gt v Search Network Connections Organize v Disable this network device Diagnose this connection
134. rs and the channel for DAP 1150 and the remote access point To use the access point as a wireless client you need to configure the same channel of the wireless connection for DAP 1150 and the remote access point Other parameters of the wireless network of DAP 1150 do not depend upon the settings of the remote access point Internet Wireless Access Point y Y AU gt N DAP 1150 4 SF Figure 50 Connecting DAP 1150 in the access point mode as a client To allow the devices from the LAN of DAP 1150 to obtain the IP addresses from the DHCP server of the remote access point or network it is necessary to disable the built in DHCP server of the device To do this proceed to the Net LAN page then in the DHCP server section in the Mode drop down list select the Disable value and click the Save button Page 60 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual DAP 1150 pue ni nas wi PR Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Enable dient E List of wireless networks Available wireless networks 18 Unknown wireless networks 0 SSID BSSID Wireless mode Channel Network Authentication Signal level DIR 320NRU 00 22 44 55 66 77 802 11b g n 1 Open net anil 100 DIR 620 00 0D 56 64 52 22 802 11b g n 1 Open net anil 100 Develop 00
135. ser Manual Overview Back Panel 5V 1 2A RESET Figure 2 Back panel view Port Description Access point mode an Ethernet port to connect to a computer LAN Router mode an Ethernet port to connect to a cable or DSL modem or to a private Ethernet line it is recommended to use the cable included in the delivery package A button to restore the factory default settings RESET Power off the device Push the RESET button Power on the device keeping the RESET button pushed and after 5 seconds release the button The device is equipped with a detachable antenna Reverse SMA Page 11 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Overview User Manual Delivery Package The following should be included Access point DAP 1150 Power adapter 5V 1 2A Ethernet cable CAT 5E CD ROM with User Manual and Quick Installation Guide Quick Installation Guide brochure Using a power supply with a different voltage rating than the one included will cause damage and void the warranty for this product Page 12 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection CHAPTER 3 INSTALLATION AND CONNECTION Before You Begin Please read this manual prior to installing the device Make sure that you have all the necessary information and equipment Operating System Configuration of the access point DAP 1150 supporting the
136. server IP field is displayed on the page The start IP address of the address pool used by the DHCP server to distribute IP addresses to clients The end IP address of the address pool used by the DHCP server to distribute IP addresses to clients The lifetime of IP addresses leased by the DHCP server At the end of this period the leased IP address is revoked and can be distributed to another device unless the previous device has confirmed the need to keep the address External DHCP server IP The IP address of the es DHCP server which assigns IP addresses to the access point s clients When all needed settings are configured click the Save button Lease time Page 124 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ON Configuring Device Router Mode User Manual Wi Fi In this menu you can specify all needed settings for your wireless network Common settings On the Wi Fi Common settings page you can enable your wireless local area network WLAN and split it into parts D Link o DAP 1150 piana uc anian Wi Fi Advanced Firewall Control System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Enable Wireless gj MBSSID Disabled w BSSID F0 7D 68 8D 81 B2 v Change Figure 112 Common settings of the wireless LAN The Enable Wireless checkbox enables Wi Fi connections By default the checkbox is selected
137. sing its web based interface D I ink System X Language y DAP 1150 pisam Status Net Wi Fi Advanced Firewall System Network statistics LAN clients IP address Flags MAC address Interface 192 168 1 40 0x2 1C 6F 65 B0 82 BA LAN 192 168 1 77 0x2 00 30 48 FE DB EC LAN L 4 Figure 32 The Status LAN clients page For each device the following data are displayed the IP address the MAC address and the interface to which the device is connected Page 38 of 175 DAP 1150 Wireless Access Point Supporting Router Mode A Configuring Device Access Point Mode User Manual Net In this menu you can configure basic parameters of the local area network of the access point LAN To configure the access point s local interface proceed to the Net LAN page IP Address 192 168 0 50 Netmask 255 255 255 0 Figure 33 Basic settings of the local interface If needed edit the basic settings of the local interface Parameter Description IP Address The IP address of the access point in the local subnet By default the following value is specified 192 168 0 50 The mask of the local subnet By default the following value is specified 255 255 255 0 When needed settings are configured click the Save button In the Static DHCP section you can specify MAC address and IP address pairs set a fixed IP address in the local area network for a device with a certain MAC address The access point assigns IP addr
138. stem events deselect the Logging checkbox and click the Change button On the Log tab the events specified in the Logging level list are displayed D Link DAP 1150 Start Status Net Wi Fi Advanced Firewall System Administrator password Configuration System log Firmware upgrade Confiauration Log Jan 103 03 19 syslogd started BusyBox v1 19 2 Telnet System v Language v Refresh Export Figure 58 The System System log page The Log tab To view the latest system events click the Refresh button To save the system log to your PC click the Export button and follow the dialog box appeared Page 68 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Firmware Upgrade On the System Firmware upgrade page you can upgrade the firmware of the access point Upgrade the firmware only when the access point is connected to your PC via a wired a connection available only in the access point mode D Link q AA DAP 1150 Start Status Net Wi Fi Advanced Firewall System Administrator password Configuration System log Firmware upgrade Telnet Select update file m mmn Update Figure 59 The System Firmware upgrade page The current version of the device s firmware is displayed in the Firmware version field on the Start page If you need to install a newer version of the firmware follow the next steps Atten
139. t Answering response requests while transmitting Displayed only in the Parameters of Access Point section Ack If not selected the access point answers requests If selected the access point does not answer requests When you have configured the parameters click the Change button Page 143 of 175 DAP 1150 Wireless Access Point Supporting Router Mode oo Configuring Device Router Mode User Manual Client On the Wi Fi Client page in the router mode you can configure the device as a client to connect to a WISP access point The client function in the router mode allows using DAP 1150 as a WISP repeater To use the access point as a WISP repeater you need to configure the same channel of the wireless connection for DAP 1150 and the WISP access point Other parameters of the wireless network of DAP 1150 do not depend upon the settings of the WISP access point WISP Access Point Y oe e gt amp gt DAP 1150 wireless connection only 7 Mi Figure 126 Connecting DAP 1150 in the router mode as a client After configuring the device as a client you need to create a WAN connection with relevant parameters for the WiFiClient port Page 144 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual DAI ink System X Language y DAP 1150 ps nnn wi a Common settings Basic settings Security settings MAC Filter Station
140. t Supporting Router Mode User Manual Configuring Device Access Point Mode When the Open or Shared value is selected the WEP Encryption settings section is displayed the section is unavailable for the wireless network operating modes which support the standard 802 11n Network Authentication WEP Encryption settings Enable Encryption WEP Default Key ID Encryption Key WEP as HEX Encryption Key WEP 1 Encryption Key WEP 2 Encryption Key WEP 3 Encryption Key WEP 4 Figure 40 The Open value is selected from the Network Authentication drop down list Parameter Enable Encryption WEP Default Key ID Encryption Key WEP as HEX Encryption Key WEP 1 4 Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field the Encryption Key WEP as HEX checkbox and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected The number of the key from first to fourth which will be used for WEP encryption Select the checkbox to set a hexadecimal number as a key for encryption Keys for WEP encryption The access point uses the key selected from the Default Key ID drop down list It is required to specify all the fields You can specify keys containing 5 or 13 symbols use digits and or Latin characters If the Encryption Key WEP as HEX checkbox is selected you can specify only keys
141. t a hexadecimal number as a key for encryption Keys for WEP encryption The access point uses the key selected from the Default Key ID drop down list It is required to specify all the fields You can specify keys containing 5 or 13 symbols use digits and or Latin characters If the Encryption Key WEP as HEX checkbox is selected you can specify only keys containing 10 symbols the digits 0 9 and the characters A F Page 34 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed value is selected the WPA Encryption settings section is displayed Security settings Network Authentication WPA2 PSK gt Encryption Key PSK 76543210 WPA2 Pre authentication T WPA Encryption settings WPA Encryption TKIP WPA reneval 3600 Figure 29 The WPA2 PSK value is selected from the Network Authentication drop down list Parameter Description Encryption Key PSK A key for WPA encryption The key can contain digits and or Latin characters WPA2 Pre The checkbox activating preliminary authentication displayed only ae for the WPA2 PSK and WPA PSK WPA2 PSK mixed authentication oats authentication types WPA Encryption An encryption method TKIP AES or TKIP AES The time period in seconds at the end of which a new key for WPA WPA renewal encryption is generated When the value 0 is specified for this field
142. t channel This parameter defines the length of the CRC block sent by the access point when communicating to wireless devices Select a value from the drop down list TX Preamble Long Preamble Short Preamble this value is recommended for networks with high volume traffic When you have configured the parameters click the Change button Page 141 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual WMM On the Wi Fi WMM page you can enable the Wi Fi Multimedia function The WMM function implements the QoS features for Wi Fi networks It helps to improve the quality of data transfer over Wi Fi networks by prioritizing different types of traffic To enable the function select the WMM checkbox and click the Change button D Link a DAP 1150 Wi Fi EAS IN ES Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client WMM Y Parameters of Access Point AC Aifsn CWMin CWMax Txop ACM Ack AC_BK 7 ly 1023 y 0 AC_BE 3 15 y 63 y 0 AC_VI 1 7 15 y 94 m AC_VO 1 3v 7v 47 E E Parameters of Station AC Aifsn CWMin CWMax Txop ACM AC_BK E 15 y 1023 y 0 AC_BE 3 15 y 1023 v 0 AC_VI 2 7 15 y 94 AC_VO 2 3 y 7v 47 a Change L Figure 125 The page for configuring the WMM function I All needed settings for the WMM function are specified in the device s system It is m recommended not to change the d
143. te from the drop down list or select Template Custom to specify all parameters of the new virtual server manually A name for the virtual server for easier identification You can specify any name Interface A WAN connection to which this virtual server will be assigned A protocol that will be used by the new virtual server Select a value Protocol from the drop down list A port of the access point from which traffic is directed to the IP Public port begin address specified in the Private IP field Specify the start and the end value for the port range If you need to specify one port enter the needed value in the Public port begin field and leave the Public port end field blank Public port end A port of the IP address specified in the Private IP field to which traffic is directed from the Public port Specify the start and the end value for the port range If you need to specify one port enter the needed value in the Private port begin field and leave the Private port end field blank Private port begin Private port end The IP address of the server from the local area network To choose d a device connected to the access point s LAN at the moment select Private IP the relevant value from the drop down list located to the right of the Private IP field the field will be filled in automatically Remote IP The IP address of the server from the external network Click the Change button To
144. ter Description ssp The name of the network to which the access point connects The unique identifier of the network to which the access point connects The authentication type of the network to which the access point connects Network Authentication Page 145 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual When the Open or Shared authentication type is selected the following fields are available Parameter Description The checkbox activating WEP encryption When the checkbox is selected the Default Key ID field and four Encryption Key WEP fields are displayed on the page For the Shared authentication type the checkbox is always selected first to fourth which will fi Default Key ID The number at the key from first to fourth which will be used for WEP encryption Keys for WEP encryption The access point uses the key selected Encryption Key WEP 1 from the Default Key ID drop down list It is required to specify 4 all the fields You can specify keys containing 5 or 13 symbols use digits and or Latin characters When the WPA PSK WPA2 PSK or WPA PSK WPA2 PSK mixed authentication type is selected the following fields are available Enable Encryption WEP Parameter Description WPA Encryption An encryption method TKIP AES or TKIP AES ion tain digit Lati Encryption Key PSK A key for WPA encryption The key can contain digits and o
145. th dynamic IP addresses D Link System DAP 1150 Start Status Net WiFi Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP DDNS client configuration DDNS Service User name Interface X Language v Update period min Figure 129 The Advanced DDNS page To add a new DDNS service click the Add button D Link System Language v DAP 1150 pamm ci an Advanced Firewall Control System UPnP DDNS DNS Routing Device mode Remote access IGMP DDNS client editing DDNS Service DLinkDDNS v Host name User name User password Interface dynamic WAN_1 v Update period min Change Figure 130 The page for adding a DDNS service Page 148 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual You can specify the following parameters Parameter Description DDNS Service Select a DDNS provider from the drop down list Hostname The domain name registered at your DDNS provider The username to authorize for your DDNS provider The password to authorize for your DDNS provider Select a WAN connection which IP address will be used to access Interface the DDNS service An interval in minutes between sending data with the IP address of Update period the interface specified in the field above to the relevant DDNS service Click the Change button To edit parameters of the existing DDNS service click the rel
146. the MAC address field of the MAC address adding section and click the Add button To add the MAC address of a device connected to the access point s LAN at the moment select the value containing the MAC and IP address of this device from the drop down list located to the right of the MAC address field the field will be filled in automatically and click the Add button To remove a MAC address from the list of MAC addresses select the checkbox located to the right of the relevant MAC address in the MAC address list section and click the Delete button Page 49 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Station List On the Wi Fi Station List page you can view the list of wireless clients connected to the access point Devices connected to the access point via the WDS function are not displayed in the list D Link ae DAP 1150 pr ns lan wi Pa Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client MAC AID PSM MIMOPS mes Bw SGI STBC OE al 34 08 04 28 3C B9 1 0 7 20M o Figure 45 The list of the wireless clients If you want to disconnect a wireless device from your WLAN select the checkbox in the line containing the relevant MAC address and click the Disconnect button To view the latest data on the devices connected to the WLAN click the Refresh button Page 50 of 175
147. the address of a device connected to the access point s LAN at the moment To do this select the relevant value from the drop down list located to the right of the field the field will be filled in automatically Obtain DNS server addresses Y automatically Vendor ID Miscellaneous Enable RIP Enable IGMP Multicast NAT firewall Figure 102 The page for creating a new connection The IP and Miscellaneous sections Parameter Description Obtain DNS server Select the checkbox to configure automatic assignment of DNS addresses server addresses If the checkbox is selected the Primary DNS automatically server and Secondary DNS server fields are not displayed Primary DNS server Enter addresses of the primary and secondary DNS servers in the Secondary DNS server relevant fields Vendor ID The identifier of your ISP Optional Enable RIP Select the checkbox to allow using RIP for this connection Select the checkbox to allow multicast traffic from the external network e g video streaming to be received Enable IGMP Multicast Page 111 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Parameter Description NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN Select the checkbox to enable protection against ARP and DDoS attacks When all needed settings are configured c
148. the higher is the Access Category priority Contention Window Minimum Contention Window Maximum Both fields influence time delays for the relevant Access Category The CWMax field value should not be lower than the CWMin field value The lower the difference between the CWMax field value and the CWMin field value the higher is the Access Category CWMin CWMax priority Txo Transmission Opportunity The higher the value the higher is the P Access Category priority Admission Control Mandatory ACM If selected prevents from using the relevant Access Category Acknowledgment Answering response requests while transmitting Displayed only in the Parameters of Access Point section Ack If not selected the access point answers requests If selected the access point does not answer requests When you have configured the parameters click the Change button Page 59 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Client On the Wi Fi Client page in the access point mode you can configure the device as a client to connect to a wireless access point The client function in the access point mode allows using DAP 1150 as a wireless client and a wireless repeater To use the access point as a wireless repeater you need to configure the same parameters of the wireless connection the name of the wireless network encryption paramete
149. tings page you can enable your wireless local area network WLAN and split it into parts D Link A DAP 1150 Start Status Net Wi Fi Advanced Firewall System Common settings Basic settings Security settings MAC Filter Station List WPS WDS Additional settings WMM Client Enable Wireless Y MBSSID Disabled BSSID F0 7D 68 8D 81 B2 v Figure 36 Common settings of the wireless LAN The Enable Wireless checkbox enables Wi Fi connections By default the checkbox is selected If you want to disable your WLAN deselect the Enable Wireless checkbox The access point allows splitting your WLAN into several parts up to four with their own names SSIDs and unique identifiers BSSIDs To split the network into several parts select a relevant value 2 3 or 4 from the MBSSID drop down list By default the wireless network is not splitted the Disabled value is selected from the list The value from the BSSID drop down list is the unique identifier for your Wi Fi network You cannot change the value of this parameter it is determined in the device s internal settings If you have splitted your WLAN into parts the BSSID drop down list contains several values Each identifier corresponds to a single part of the WLAN For every part of the WLAN you can specify a name SSID security settings rules for MAC filtering and enable the WMM function if needed To specify these values select the needed part from the BSSID drop
150. tion Do not turn off the access point before the firmware upgrade is completed a This may cause the device breakdown 1 Download a new version of the firmware from www dlink ru 2 Click the Choose Browse button on the System Firmware upgrade page to locate the new firmware file Click the Update button to upgrade the firmware of the access point Wait until the access point is rebooted about one and a half or two minutes Log into the web based interface using the login admin and the current password SS wa SS Select the Factory line in the top page menu displayed when the mouse pointer is over the System caption 7 Wait until the access point is rebooted Log into the web based interface using the default IP address login and password 192 168 0 50 admin admin 2 The name of the button depends upon the web browser that you use Page 69 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual Telnet On the System Telnet page you can enable or disable access to the device settings via TELNET from your LAN By default access is enabled D Link 31mm DAP 1150 Start Status Net Wi Fi Advanced Firewall System Administrator password Configuration System log Firmware upgrade Telnet Telnet Change Figure 60 The System Telnet page To disable access via TELNET deselect the On checkbox and click the Change button To
151. ttings are configured click the Save button Page 117 of 175 DAP 1150 Wireless Access Point Supporting Router Mode ee Configuring Device Router Mode User Manual Creating PPTP Dynamic IP or L2TP Dynamic IP WAN Connection To create a connection of the PPTP Dynamic IP or L2TP Dynamic IP type click the Add button on the Net WAN page On the opened page select the relevant value from the Connection Type drop down list and specify the needed values General settings PPTP Dynamic IP y WAN vw dynpptp_WAN_2 T WAN 1500 F0 7D 68 8D 81 B2 lt Select address gt v Clone MAC Figure 106 The page for creating a new connection The General settings and Ethernet sections Parameter Description General settings A physical interface to which the new connection will be assigned A name for connection for easier identification Select the checkbox to enable the connection The direction of this connection OO MU The maximum size of units transmitted by the interface MAC A MAC address assigned to the interface This parameter is mandatory if your ISP uses MAC address binding In the field enter the MAC address registered by your ISP upon concluding the agreement You can click the Clone MAC button to set the MAC address of the network interface card of the computer that is being used to configure the access point at the moment as the MAC address of the WAN interface Also you can set the addr
152. ual To activate the WPS function select the WPS Enable checkbox and click the Change button When the checkbox is selected the Information and Connection sections are available on the page Parameter Description The PIN code of the access point This parameter is used when Default PIN code connecting the access point to a registrar to set the parameters of the WPS function The state of the WPS function e Configured all needed settings are specified e Unconfigured you need to specify the relevant settings The name of the device s WLAN or the first part of the WLAN if the network is splitted into parts san The network authentication type specified for the WLAN or first k Authen n Network Authenticatio part of the WLAN Encryption a ooo type specified for the WLAN or the first part of the E The encryption key specified for the WLAN or the first part of the k Encryption key WLAN Click the button to view the latest data on the state of connecting the wireless device via the WPS function Reset to unconfigured Click the button to reset the parameters of the WPS function A method of the WPS function Select a value from the drop down list WES Merngg PIN Connecting the device via the PIN code PBC Connecting the device via the push button actual or virtual The PIN code of the WPS enabled device that needs to be connected to the wireless network of the access point PIN Code The field is displayed only when t
153. uan O A A E alah eens 100 Routing TAE E A wR ME AA alana AAA AAA Je he Wire Ree A el a ae 101 EAN CLrENUS a tare A AS oe A Ri a Oar 102 Neto it A A A Fee A A AS AA Benes a A AE A etch ae 103 WAN ES SS Sh A O a dal Sek UN dos de 103 Creating PPPOE WAN CONNECELO Mi A A A a OS 104 Creating Static IP MAN COnNe CULO seek sic a a 107 Creating Dynamre LP WAN CONNOE CLON A A nite A eee a 110 Creating PPTP Static IP or L2TP Static IP WAN Connection 113 Creating PPTP Dynamic IP or L2TP Dynamic IP WAN Connection 118 EAN ts dese ai See Des eal duos O A Sree Bee we Dad Sle EA hen Oe Oat Mee is 123 Page 3 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual WISSEL gasy AS A A A A o a les dee eek eee 125 Common SSE GS econ ctel soe se A A AA Tease A ZO Basto S t Ging Sv sei i eco Wie PM Eke ela Ad AAA We ne eee ene ia bree Nee we ee Alas See a DDG SECUTTEY SELECIONAR e eZ MAC ELLE As AI ti Ad o ds LOS Statron E A A O Gna dds a A a dd dd 34 MB a e a NE E la as atra 35 WD a E E E G AS lia NEP A tara he leal 38 Addrtional SETCCINDOS e ts ai DR Beal a Go ele E E E a tad dd 40 WMM rons ES EAT DIAS EAS EEES AIR RAS A AS A SN do Steve vents 42 ELSE a ES SAR ARES ARA E AA 44 Advanced io a aie te bee esha AA ee at mee 147 UBD PAS Seipah cecal E Lev E AT A ideas Geese ede AL ei sl 47 DONGRE ai ee th eh e ES A hh NE E O De aa ter all 48 ONSE A des o A A Sat dada aE Teo eo Nat T
154. uick settings page opens Page 92 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Site Setup Wizard To create a virtual server for redirecting incoming Internet traffic to a specified IP address in the LAN click the Host site button Virtual server settings Interface WAN E Private IP lt Select address gt w Figure 85 The page for adding a virtual server On the opened page you can specify the following parameters Parameter Description Enter a name for the virtual server for easier identification You can specify any name Select a WAN connection to which this virtual server will be Interface f assigned Enter the IP address of the server from the local area network To choose a device connected to the access point s LAN at the moment select the relevant value from the drop down list located to the right of the Private IP field the field will be filled in automatically Remote IP Enter the IP address of the server from the external network When needed settings are configured click the Save button After that you get to the quick settings page Private IP Page 93 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Router Mode User Manual Wi Fi Setup Wizard To specify all needed settings for your wireless network click the Configure Wi Fi button Common settings Enable Wireless
155. ve settings every time you change the device s parameters Save Otherwise the changes will be lost upon hardware reboot of the access point Click the button to restore the factory default settings Also you can Factory restore the factory defaults via the hardware RESET button see the Saving and Restoring Settings section page 29 Backu Click the button and follow the dialog box appeared to save the P configuration all settings of the access point to your PC Click the button to upload a previously saved configuration all settings of the access point from a file on your PC Click the Restore 4 Choose Browse button to select a previously saved configuration file located on your PC Actions of the Save Factory and Backup buttons also can be performed via the top page menu displayed when the mouse pointer is over the System caption 1 The name ofthe button depends upon the web browser that you use Page 66 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual System Log On the System System log page you can set the system log options and configure sending the system log to a remote host D Li ni 4 System v Language nd DAP 1150 Administrator password Configuration System log Firmware upgrade Telnet Configuration Log Logging E Logging type Local and remote v Logging level Informational messages v Server address type P v Server
156. ways enabled this setting can substantially lower the efficiency of your wireless network Always Off The protection function is always disabled The channel bandwidth for 802 11n devices 20MHz 802 11n devices operate at 20MHz channels 40MHz 802 11n devices operate at 4OMHz channels Bandwidth 20 40MHz 802 11n devices operate at 20MHz and 40MHz channels the channel is combined with the previous adjacent channel 20 40MHz 802 11n devices operate at 20MHz and 40MHz channels the channel is combined with the next adjacent channel This parameter defines the length of the CRC block sent by the access point when communicating to wireless devices Select a value from the drop down list TX Preamble Long Preamble Short Preamble this value is recommended for networks with high volume traffic When you have configured the parameters click the Change button Page 57 of 175 DAP 1150 Wireless Access Point Supporting Router Mode Configuring Device Access Point Mode User Manual WMM On the Wi Fi WMM page you can enable the Wi Fi Multimedia function The WMM function implements the QoS features for Wi Fi networks It helps to improve the quality of data transfer over Wi Fi networks by prioritizing different types of traffic To enable the function select the WMM checkbox and click the Change button D I ink System X Language X DAP 1150 Start Status Net Wi Fi Advanced Firewall System Common settings
157. wireless network connection and make sure that your Wi Fi adapter is on Network Connections Ele Edit View Favorites Tools Advanced Help Q x X J O Pp Search gt Folders EE Name Type etwork Tasks 8 LAN or High Speed Internet x Create a new connection oy LAN or High Speed Viami 2 nr a LL 1394 Connection LAN or High Speed Internet Change Windows Firewall lt b Local Area Connection LAN or High Speed Internet etting View available wireless networks BS Disable this network device amp Repair this connection Rename this connection 2 Change settings of this connection mee A Figure 11 The Network Connections window 3 Search for available wireless networks 4 In the opened Wireless Network Connection window select the wireless network DAP 1150 and click the Connect button After that the Wireless Network Connection Status window appears If you perform initial configuration of the access point via Wi Fi connection note that I immediately after changing the wireless default settings of the access point you will need to reconfigure the wireless connection using the newly specified settings Page 22 of 175 DAP 1150 Wireless Access Point Supporting Router Mode User Manual Installation and Connection Configuring Wi Fi Adapter in OS Windows 7 1 Click the Start button and proceed to the Control Panel window 2 Select the Network and Sharing Center section If the Control Panel
158. you can change the operating mode of the device D Link a DAP 1150 POET OCMC Advanced Device mode Device work mode settings Work mode Change Figure 52 The page for changing the operating mode of the device To switch the device to the other mode select the Router value from the Work mode drop down list and click the Change button Then select the Save amp Reboot value from the top page menu displayed when the mouse pointer is over the System caption and wait until the device is rebooted When the device is switched to the router mode you cannot connect to it via a wired connection Page 63 of 175 DAP 1150 Wireless Access Point Supporting Router Mode NS Configuring Device Access Point Mode User Manual Firewall In this menu you can configure the firewall of the access point MAC Filter On the Firewall MAC filter page you can configure MAC address based filtering for computers of the access point s LAN DA ink System X Language X DAP 1150 P Firewall MAC filter MAC filter configuration i You can add edit and delete addresses here MAC address Action Figure 53 The Firewall MAC filter page To specify a new address for the MAC filter click the Add button D Link System X Language X DAP 1150 MAC filter MAC address editing MAC address lt Select address gt v Action Alow v Change Figure 54 The page for adding an address for the MAC

DAP-1150_User Manual_v.1.3.0_29.12.11_EN - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents