User`s Manual
Contents
1. ace PLC Modbus RTU Gateway migan Modbus RTU iis i Modbus RTU con Igura lon RS485 Controller Board Display Modules Page 3 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 2 1 Device Configuration Character Height C 60 mm 100mm 150mm 200mm 250 mm Number of Lines Number of Digits per Line O1 02 Es U4 O5 Eje Liz 8 28910 11 12 013 014 15 Display Colour red green yellow Dimensional Display Line 1 Line 5 Line 2 Line 6 Line 3 Line 7 Line 4 Line 8 View L single sided double sided L quadruple sided Operating Voltage 1230V 50 Hz 110v 60 Hz 124 V DC Protection IP40 IP54 IP65 Temperature Range L Oto 50 C _ 25 to 50 C Housing dimensions X X mm Housing Colour RAL Housing Material Aluminium profile L Stainless steel Sheet metal Device Address Page 4 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 3 Technical Information 3 1 Overall Specification Display type Character heigh2. arantee does not cover defects which result from non observance of the prescribed conditions of use or from improper handling If the device has been placed at the disposal of the buyer for test purposes and has been purchased subsequent to such testing both parties agree that the product is to be considered used and that it has been purchased as is No guarantee claims may be made in such cases The General Terms and Conditions regarding manufactured products and services rendered for the electrical industry apply as well Page 17 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 4 5 Versions Overview Remark Description 29 11 07 Kreuzer Document created 20 12 07 Nickl Revised Certified per DIN EN ISO 9001 2000 Page 18 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de
3. ator for Modbus RTU Page 7 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface Display Data Positioning LI LI d LLL LI rtt oo D1 is the 1st digit from the left side of the display Dn is the nth digit from the left side of the display n 2 15 Decimal Point Bytes If a decimal point needs to be set the corresponding bit must be 1 P1 bin 010XXXXX lL pigits Digit 4 Digit 3 Digit 2 Digit 1 P2 bin 010XXXXX L Digit10 Digit 9 Digit 8 Digit 7 Digit 6 P3 bin 010XXXXX L Digit 15 Digit 14 Digit 13 Digit 12 Digit 11 micro SYST So if no decimal point needs to be set P1 P2 and P3 contain 40 each microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de Page 8 micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface Example for a ModbusRTU Telegram Request in hex 01 17 04 02 00 08 04 02 00 08 10 55 5F 5F 31 32 33 34 35 36 37 38 39 30 31 32 33 FC F8 01 ModbusRTU node address 17 ModbusRTU function code for Read Write Registers 04 02 00 08 04 02 00 08 10 Read Write 8 Reg
4. busRTU communication parameters are set via DIP switches inside the housing see below and will not be displayed Page 6 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 3 3 Display Control Via ModbusRTU The display represents a ModbusRTU Slave and is controlled by a ModbusRTU Master f e a PLC To change the display contents the ModbusRTU Master has to write to some Registers Therefore the commands Force Multiple Registers function code 1647104 or Read Write Registers function code 2347174 can be used Here we assume that Registers are counted beginning at 0 If your PLC starts counting at 1 you may have to increase the register address by 1 The following data has to be written starting at register address 04024 04024 HIGH P1 decimal point byte 1 for digits 1 5 1 EET 5 04054 HIGH D4 ASCII code for digit 4 0407 HIGH D8 ASCII code for digit 8 D9 ASCII code for digit 9 D13 ASCII code for digit 13 040A HIGH D14 ASCII code for digit 14 D15 ASCII code for digit 15 Remarks Upto 15 digits are possible tis not necessary to initialize unused digits Registers 402 40Ay correspond to the output data area 2044 215 of the used HMS Anybus Communic
5. croSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 7pol Mains Plug 230 VAC 3 4 2 Internal LEDs and Switches micro SYST 3 Processing LED State Description Off Normal operation vede Red Bus error CRC mismatch gt 10 Off Not powered 2 Bus Ready Green Normal operation bus ready Red Bus is off line bus not ready Off Currently not processing query Green flashing Currently processing query 4 HW Settings Off Normal operation 6 Device Status Red Not configured Off Power off 5 Subnet Status Green flashing Initializing and not running Green Running Red Stopped or subnet error or timeout Off Power off Alternating Red Green Invalid or missing configuration Green Initializing Green flashing Configuration OK microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Page 11 Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST I migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface Inggmgmgmgmmolounounununl ModbusRTU HH i Node Address HALL RD Node Address DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 r
6. ed by qualified per sonnel and nothing has to be touched inside the housing at this time Otherwise electrical shock and danger to life may happen Please be careful Page 13 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de Wa micro SYST MIQan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 4 Appendix 4 1 Displayable Characters The data bytes are ASCII coded me dic e ead T ws ew 8 R R ES NN UNE ER ES ER cA A ar b r Ls p oppo e BEE poew EE E LJ LJ EROR a ERR SR RI RUORRRNE pone pL E Page 14 roSYST Systemelectronic GmbH Zur Centralwerkst tte 10 shen Weiden German y Tel 49 961 3 91 66 0 Fax are www microsyst info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 4 2 Maintenance and Care Observe the following instructions in order to assure best possible perform ance of the display Make sure that the housing can be opened for adjustment and mainte nance even after the display has been installed Allow for adequate clear ance at the back front and top of the display unit in order to allow for suf ficient ventilation if vent slots are included Display quality is impaired by direct illumination with bright light sources and or direct sunlight The display must be switched off before clea
7. eserved OFF OFF OFF OFF OFF OFF OFF j OFF OFF OFF OFF OFF OFF ON 2 OFF OFF OFF OFF OFF ON OFF 126 ON ON ON ON ON ON OFF 127 ON ON ON ON ON ON ON Factory Setting ModbusRTU i UE Baudrate ON N Baudrate DIP8 DIP1 DIP2 reserved OFF OFF OFF 1200 baud OFF OFF ON 2400 baud OFF ON OFF 4800 baud OFF ON ON 9600 baud ON OFF OFF 19200 baud ON OFF ON 38400 baud ON ON OFF 57600 baud ON ON ON z Factory Setting ModbusRTU i i Hi Parity amp Stop Bits N N Pay X DP3 X DP O No parity 2 stop bits Even parity 1 stop bit Odd parity 1 stop bit z Factory Setting ModbusRTU a Physical Interface N N ON RS485 z Factory Setting Page 12 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface Important note To change the setting of the DIP switches obey the following order disconnect the power supply open the housing open the dip switch protection cap carefully using a little srew driver set the dip switches as desired Close the dip switch protection cap close the housing reconnect the power supply While the housing is open power may only be appli
8. generic standard EN 50082 2 issued March 1995 Basic specification per table In accordance with regulations specified by guideline 89 336 EWG and EMVG Weiden 22 November 1999 microSYST Systemelectronic GmbH Page 16 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 4 4 Guarantee The display is guaranteed for the duration specified in the General Terms and Conditions regarding manufactured products and services rendered for the electrical industry period against defects which existed at the time the device was delivered to the buyer The device is subject to technical change without notice Errors and omissions are excepted No claims can be honoured for the shipment of a new product The buyer is required to make notification of defects within 2 weeks after iden tification of such Non observance of notification requirements is equated with acceptance of the defect Defects and their symptoms must be described as accurately as possible in order to allow for reproducibility and elimination The buyer must provide for access to all required and or useful information regarding defects at no charge as well as to the affected devices and must make all of the required data and machine time available free of charge The gu
9. isters starting at 04024 55 SF SF 31 32 33 34 35 36 37 38 39 30 31 32 33 New Display Data all points set except at digit 2 and 4 display 12345 FC F8 CRC16 FFFF Checksum Remark The ModbusRTU communication normally is done automatically by the PLC The user just has to set up the destination register addresses and the data part of the telegram point bytes and digit data Page 9 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 3 4 Connector Pin Assignments 3 4 1 External Connections 9pol Sub D Female Connector ModbusRTU Pin Assignment 1 E LU uM 6 5SVBusOut RS 485 DO Rx Tx 8 RS 485D1 Rx Tx za Remark Depending on DIP5 of the ModbusRTU interface see below either the RS232 pins or the RS485 pins may be used The unused pins have to be left open Do not use a standard RS232 cable where all pins are connected Otherwise the ModbusRTU interface may be destroyed 9pol Sub D Male Connector Configuration RS232 Remark This connector should not be used by the customer The configura tion is already done by microSYST and must not be changed Otherwise the correct function of the display can not be guaranteed Page 10 mi
10. migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface User s Manual microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface Index 1 GENERAL 2 SYSTEM OVERVIEW 2 1 Device Configuration 3 TECHNICAL INFORMATION 3 1 Overall Specification 3 2 Device Start Up 3 3 Display Control Via ModbusRTU 3 4 Connector Pin Assignments 3 4 1 External Connections 3 4 2 Internal LEDs and Switches 4 APPENDIX 4 1 Displayable Characters 4 2 Maintenance and Care 4 3 Declaration of Conformity 4 4 Guarantee 4 5 Versions Overview microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST 10 11 14 14 15 16 17 18 Page 2 micro SYST Migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 1 General The large format numeric display can be used universally as a produc tion display unit or as an information board The modular design allows for cost effective models of various sizes and with different character heights and numbers of digits Thus integration into existing equipment or systems is easy and simple 2 System Overview The display is controlled with a ModbusRTU interf
11. ning Protect the display from excessive humidity extreme vibration direct sunlight and extreme temperatures Non observance may lead to mal functioning or destruction of the device Under certain circumstances elec trical shock fire and explosion may occur as well Information concerning allowable ambient conditions including recommended temperature ranges can be found in the chapter entitled Technical Information The display may not be placed into service if the device and or the power cable are known to be damaged Do not attempt to repair the device yourself The guarantee is rendered null and void if the device is tampered with by unauthorised persons Page 15 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 4 3 Declaration of Conformity microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 92637 Weiden Germany does hereby declare that the product described in this user s manual migan to which this declaration makes due reference is in compliance with the following standards or normative documents Interference emission generic standard EN 50081 2 issued July 1993 Product standard EN 55011 group 1 2 class A issued March 1991 Limit values identical to EN 55022 Interference immunity
12. t Digits Display colour Character set View Interface Operating voltage Power Consumption Housing Housing dimensions Mounting Protection Operating temp Storage temperature 7 segment LED 60 mm 2 36 100 mm 3 94 150 mm 5 91 200 mm 7 87 250 mm 9 84 2 to 15 digits red green yellow see chapter Displayable Characters single double or quadruple sided ModbusRTU 230 V 50 Hz 110 V 60 Hz or 24 VDC 60 mm 2 36 approx 1 3 W per digit 100 mm 3 94 approx 2 5 W per digit 150 mm 5 91 approx 7 0 W per digit 200 mm 7 87 approx 7 5 W per digit 250 mm 9 84 approx 10 0 W per digit industrial version powder coated aluminium see chapter Device Configuration articulated arm hanging mount bracket for wall mounting IP54 or IP65 0 to 50 C optional 25 to 50 C 25 to 70 C Page 5 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Tel 49 961 3 91 66 0 Fax 49 9 61 3 91 66 10 www microsyst de info microsyst de micro SYST migan ModbusRTU Large Display Numeric LED with Modbus RTU Interface 3 2 Device Start Up Internal memory and function tests are performed at the large format display during power up The following parameters appear e Baud rate e Parity e Internal Address These parameters do not have a meaning for the user and serve merely for diagnostic purposes of the internal RS485 interface The Mod
Download Pdf Manuals
Related Search