SATA III + PATA COMBO RAID CARD
Contents
1. About 10 15 PM 272. Figure 16 Replace Physical Disk Marvell BIOS Setup c 200 Technology Group Ltd Virtual Di P 0 vD 0 SATA PD LPD Unconfigured L Free s 157066MB NCO 36 488its 36 Hitachi H0S721616PLA380 OVE3O1ZFRGZL8M P220ABEA Physical Disk can be into a vD ENTER Operation it Save ESC Return In the Topology pane scroll to Virtual Disks VD 0 New_VD in Figure 17 and press Enter to select A menu pops up as shown in Figure 17 Scroll to Rebuild and press Enter to configure the rebuild process Figure 17 Rebuild Virtual Disk 15 roup Ltd HBA 0 Marvell 0 Virtual Disks Ler Help Virtual Dis a range of co ENTER Operation F10 Exit Save ESC Return 4 Scroll through the list of free disk as shown Figure 18 and press Space to select or unselect a replacement physical disk Press Enter to continue Figure 18 Select Replacement Disk rtual Disks 64K Physical Disks Mode RAIDI 156672 MB WA bar to select the free disks to be used in the array Operation SPACE Select F10 Exit Save ESC Return 16 5 6 Press Y to select Yes as shown in Figure 19 when prompted to confirm the rebuild process Figure 19 Confirm Rebuild Virtual Disk 0 New VO 64K RAIDI 186672 NB he space bar t se t e elect the free disks to be used he array ENTER Operation SPACE Select F10 Exit Save ESC Return The status of the Rebuild process is reflected in the properties of the virtual disk as
3. RAIDO 1430800 NB WA 2 og v disk F10 Exit Save ESC Return Driver Installation For Windows XP Server 2003 For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the DS 30106 Windows Floppy32 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Follow Microsofts Windows installation procedure At the Windows Setup screen press F6 to install the driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter A ee Scroll to Marvell shared library install first using the 20 10 11 12 13 14 15 arrow keys and press Enter to select Press S again to select the second device Scroll to Marvell 91xx SATA Controller 32bit Driver and press Enter to select Press Enter to complete the installation of drivers Continue with the Windows OS installation And there is an additional device Marvell 91xx Config SCSI Processor Device is detected when Windows starts for the first time Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation After successful installation the device is listed
4. Save ESC Return Please Y to select Yes as shown in Figure 11 to confirm the creation of the virtual disk The virtual disk is now listed in the Topology pane as shown in Figure 12 Figure 11 Create Virtual Disk Confirmation 10 Stripe Size Gigabyte Rounding Quick Init VD Namo e space bar to select the free disks to be used in the array ENTER Operation SPACE Select F10 Exit Save ESC Return Figure 12 Virtual Disk in Topology Pane Technology Group Ltd 1848 Virtual Disk 9123 LVD 0 Test B1 e 0 ST3750330MS 1 0 0 1008 PD 8 ST3750330NS re cal Disk AHCI Node T Marvell R ci ENTER Operation F10 Exit Save ESC Return Managing Virtual Disks This section contains the following topics Viewing Properties of Virtual Disk 11 Erasing RAID Configuration Data Rebuilding Virtual Disk Deleting Virtual Disk Viewing Properties of Virtual Disk To view the properties of a virtual disk scroll to the Virtual Disk VD 0 Default in Figure 13 in the Topology pane The properties of the virtual disk are displayed in the Information pane when VD 0 Default is highlighted as shown in Figure 13 Figure 13 Virtual Disk Properties Functional VD 10 k 1 3750330MS ST3750330MS cal Disk 100 1430800 M8 WA 2 og Erasing RAID Configuration Data Note The RAID controller stores RAID configuration data on all physical disks that are part of a virtual disk RAID configuration 12 data m
5. for making selection are listed in the Help pane when an available setting is highlighted Figure 4 Configure Virtual Disk Stripe Size Gigabyte Rounding Quick Init las VO Nano Default Next it Save ESC Return T Note Max size MB and Disk ID are properties of the virtual disk that cannot be edited Max size MB in the size of the RAID virtual disk as determined by the selected RAID Level Disk ID lists the IDs of the physical disks comprising the virtual disk RAID Level as shown in Figure 4 is highlighted when the Create Virtual Disk screen is presented Press Enter to select a RAID Level A menu pops up as shown in Figure 5 and list lists available RAID levels Scroll the list as shown in Figure 5 and press Enter to select a RAID Level RAID 0 RAID 1 Figure 5 RAID Level Stripe Size Gigabyte Rounding Quick Init VD Name Next F10 Exit Save ESC Return Note The default Level is RAID 0 Scroll to Stripe Size and press Enter to select 6 10 A menu pops up as shown in Figure 6 and lists available stripe sizes for the selected RAID level Scroll the list as shown in Figure 6 and press Enter to select Stripe Size 32K 64K Figure 6 Stripe Size RAID Level Free Physical Disk Gigabyte Rounding PD 8 ST3750330MS Quick Init KEEL YD Hase Next 1 disk ENTER Select F10 Exit Save ESC Return Note The default size is 64 KB Scroll to Gigabyte Rounding and
6. in the Device Manager as Marvell 91xx Config Device under System Device For An Existing Installation l Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive 21 2 At the Windows desktop click Start then Run 3 Type D DS 30106 Windows Setup exe click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows XP x64 Server 2003 x64 For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the DS 30106 Windows Floppy64 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Follow Microsofts Windows installation procedure 2 At the Windows Setup screen press F6 to install the driver 3 When prompted press S to specify the location of the driver 4 Insert the floppy disk then press Enter 5 Scroll to Marvell shared library install first using the arrow keys and press Enter to select D Press S again to select the second device Scroll to Marvell 91xx SATA Controller 64bit Driver and press Enter to select 22 11 12 13 14 15 Press Enter to complete the installation of drivers Continue with Windows OS installation And there is an additional device Marvell 91xx Config SCSI Processor Device
7. press Enter to select A menu pops up as shown in Figure 7 and lists available stripe sizes for the selected RAID level Scroll the list as shown in Figure 7 and press Enter to select Gigabyte Rounding None 1G 10G Figure 7 Gigabyte Rounding 11 12 RAID Level Stripe Size sical Disk 5T3750330MS Quick Init 3750330KS VD Name Next gt Hel p rtual disk configura ENTER Select F10 Exit Save ESC Return Note The default setting for Gigabyte Rounding is 1G Scroll to Quick Init and press Enter to enable to disable quick initialization of the virtual disk A menu pops up as shown in Figure 8 and lists available options for quick initialization of the virtual disk Scroll the list as shown in Figure 8 and press Enter to select Quick Init Yes No Figure 8 Quick Init 13 ESC Return Note The default setting for Quick Init is Yes Scroll to VD Name and the Default name is cleared for a new name as shown in Figure 9 Type a new name and press Enter to confirm the selection Figure 9 VD Name rtual Disk RAID Level f irtual Di Help Virtual di ENTER Select it Save ESC Return 14 After configuring the virtual disk scroll to Next as shown in 15 Figure 10 Press Enter to create the virtual disk Figure 10 Create Virtual Disk Stripe Size Gigabyte Rounding Quick Init YD Name gt Help Virtual disk guration ENTER Select F10 Exit
8. shown in Figure 20 Figure 20 Rebuild Status 17 RAIDI 156672 NB Running ox 2 og range of consecutively number ENTER Operation F10 Exit Save ESC Return To pause the rebuild process 1 In the Topology pane scroll to the partially rebuild Virtual Disk 2 Press Enter to view available operation on Virtual Disk 3 Scroll to Pause and press Enter to pause the rebuild process Note Incomplete rebuild procedures are paused upon exiting the BIOS The rebuild procedure s can be resumed manually upon re entering the BIOS To pause the rebuild process 1 In the Topology pane scroll to the partially rebuild Virtual Disk 2 Press Enter to view available operation on Virtual Disk 18 Scroll to Resume and press Enter to resume the rebuild process Note The rebuild process is both initiated and completed in the BIOS The Marvell RAID Utility MRU which runs in an OS environment cannot be used to either initiate pause resume or complete the rebuild process Deleting Virtual Disk To delete a virtual disk l In the Topology pane select Virtual Disk VD 0 Default in Figure 21 and press Enter A menu pops up as shown Figure 21 Select Delete to delete the virtual disk as shown in Figure 21 Press Y to select Yes when prompted Do you want to delete this virtual disk Press Y to select Yes when prompted Do you want to delete MBR from this virtual disk Figure 21 Delete Virtual Disk 19
9. SATA Ill PATA COMBO RAID CARD User Manual DS 30106 All brand names and trademarks are properties of their respective owners Features and Benefits Compliant with PCl Experss Specification v2 0 and backward compatible with PCI Express 1 x Compliant with Serial ATA Specification 3 0 Supports communication speeds of 6 0Gbps 3 0Gbps and 1 5Gbps Hot plug and Hot Swap Supports Native Command Queuing NCQ Supports Port Multiplier FIS based switching or command based switching Supports ATA and ATAPI commands Compatible with SATA 6G 3G and 1 5G Hard Drives Support RAIDO function RAID 0 RAID 1 only for SATA hard drives Supports Windows XP Server 2003 Vista 7 32 64 bit Bus Interface PCI Express x1 Connectors 2 x SATA connectors e 1 x PATA connector System Requirements PCI Express enabled system with one available PCI Express slot Windows XP Server 2003 Vista 7 32 64 bit Package Contents 1 x PCle SATA 6G PATA RAID Card 1 x Driver CD 1 x User Manual Low Profile bracket Note Contents may vary depending on country market Hardware Installation 1 2 3 4 Turn off the power to your computer Unplug the power cord and remove your computer s cover Remove the slot bracket from an available PCle slot To install the board carefully align the card s bus connector with the selected PCle slot on the motherboard Push the board down firmly Attach your internal devices to t
10. he PCle SATA 6G PATA RAID Card Replace the slot bracket s holding screw to secure the card Replace the computer cover and reconnect the power cord 2 Creating and Managing Virtual Disks Creating Virtual Disks This section describes the produce for creating virtual disks using the BIOS Configuration Wizard To create a virtual disk 1 In the Topology pane scroll to HBAO Marvell 0 and press Enter to select Amenu pops up as shown in Figure 1 Select Configuration Wizard and press Enter to begin creating the virtual disk Figure 1 Configuration Wizard 1848 rtual Disk O1xx F ree Physical amp Bl PD 0 ST3750330KS 1 0 0 1008 LPO 8 ST3750330KS n 2 1 0 1316 5 0Gbps AHCI Node ENTER Operation F10 Exit Save ESC Return 2 Press Space to select unselect a disk a disk as shown in Figure 2 Use the arrow keys to scroll the list of free disks Figure 2 Select Free Disks 3 AHCI Mode gt ation SPACE Select F10 Exit Save ESC Return Note The PCle SATA 6G PATA RAID Card supports the creation of RAID 0 and RAID 1 virtual disks comprising of exactly two SATA physical disks PATA physical disks cannot be used to create RAID virtual disks After selecting the required disks press Enter to continue as shown in Figure 3 Figure 3 Confirm Disk Selection Virtual e 9ixx B1 1 0 0 1008 Create Virtual Disk by configuring its setting in the Information pane as shown in Figure 4 The controls
11. is detected when Windows starts for the first time Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation After successful installation the device is listed in the Device Manager as Marvell 91xx Config Device under System Device For An Existing Installation l Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change 23 D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows Vista 7 For A New Installation Follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press Load Driver to install the driver 3 Insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive please select Marvell 91xx SATA 6G Controller D DS 30106 Windows Floppy32 mv91xx inf then press Next Change D to match your CD ROM drive letter 4 Continue with Windows OS installation And there is an additional device Marvell 91xx Config SCSI Processor Device is detected when Windows starts for the first
12. nsert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation 10 After successful installation the device is listed in the Device Manager as Marvell 91xx Config Device under System Device For An Existing Installation Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change 26 D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation To Verify Driver Installation l 2 3 Right click My Computer and click Manage Select Device Manager Look for the following Windows 2000 XP 2003 Double click SCSI and RAID Controller Marvell 91xx SATA 6G Controller should be displayed Windows Vista 7 Double click Storage controllers Marvell 91xx SATA 6G Controller should be displayed Marvell RAID Utility MRU The MRU System Tray application is available on Windows OS and appears as an icon in the system tray Clicking this icon launches the MRU in your default browser A start B e E Marvell RAID Utility Disable Alarm Disable Popup Message Exit
13. time 6 Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run 8 Type D DS 30106 Windows Setup exe click OK Change 24 10 D to match your CD ROM drive letter Follow the on screen instructions to complete the installation After successful installation the device is listed in the Device Manager as Marvell 91xx Config Device under System Device For An Existing Installation 5 Please insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive At the Windows desktop click Start then Run Type D DS 30106 Windows Setup exe click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation For Windows Vista x64 7 x64 For A New Installation 1 2 Follow Microsoft s Windows installation procedure At the Windows Setup screen press Load Driver to install the RAID driver Insert the CD driver bound with PCle SATA 6G PATA RAID Card into your CD ROM Drive please select Marvell 91xx 25 SATA 6G Controller D DS 30106 Windows Floppy64 mv91xx inf then press Next Change D to match your CD ROM drive letter Continue with Windows OS installation And there is an additional device Marvell 91xx Config SCSI Processor Device is detected when Windows starts for the first time Please i
14. ust be erased on the physical disk before it can be used with another virtual disk 1 In the Topology pane select Physical Disk VD 0 Default gt PD 0 ST3750330MS in Figure 14 and press Enter A menu pops up as shown Figure 14 2 Select Delete to delete the virtual disk as shown in Figure 14 3 Select Yes when prompted to confirm the erase operation Figure 14 Erase RAID Configuration Data Rebuilding Virtual Disk Note The PCle SATA 6G PATA RAID Card BIOS supports manual rebuilding of RAID 1 virtual disks The rebuild process is 13 both initiated and complete in the BIOS The Marvell RAID Utility MRU which runs in an OS environment cannot be used to either initiate resume or complete the rebuild process Spare physical disks are not supported To manually rebuild a RAID 1 virtual disk 1 When a virtual disk is degraded the Status of a virtual disk is changed from Functional to Degrade as shown in Figure 15 Figure 15 Virtual Disk Properties Degrade VD 64K RAIDI 156672 NB WIA Replace the faulty physical disk with an identical physical disk Note If an identical disk is unavailable use a replacement physical disk or larger size or one with a slightly smaller size as determined the Gigabyte Rounding setting for the virtual 14 disk The PCle SATA 6G PATA RAID Card detects the new physical disk and lists the device under Free Physical Disks in the Topology pane as shown in Figure 16
Download Pdf Manuals
Related Search