User Manual USB 2.0 4
Contents
1. User Manual USB 2 0 4 Port Hub Safety Instructions Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from humidity Lay this equipment on a reliable flat surface before setting it up m m m m If any of the following situation arises get the equipment checked by a service technician o The equipment has been exposed to moisture o The equipment has been dropped and damaged o The equipment has obvious sign of breakage o The equipment is not working properly or you cannot get it to work according to User s Manual Introduction The USB 2 0 High Speed 4 port hub allows you to add multiple high performance USB 2 0 peripheral devices to your PC Moreover this product is fully backwards compatible with the USB Revision 1 1 products which means your previous USB 1 1 devices can continue to function as usual The USB 2 0 high speed hub is fully compliant with the USB 2 0 specification and permits you to connect up to a maximum of 127 USB devices to your PC through daisy chain Features 1 Compliant with Universal Serial Bus Specification Revision 2 0 Data Rate 1 5 12 480 Mbps and USB 1 1 Supports both OHCI and UHCI Supports Self power mode only Include one 1 upstream and four 4 downstream USB ports One 1 Red LED indicator for Power On LED and four 4 Green LED indicators for downstream port status e aa a Supports Plug amp Pl2. ay specification SE Over current detection and protection with LED status indicators Stackable one by one 9 Connects up to a maximum of 127 USB devices through cascading multiple hubs System Requirements gt IBM Compatible Pentium 233 MHz or faster amp MAC PCs gt 64 MB RAM or more gt PC or MAC with available USB 2 0 port gt OS support Win98SE Win ME Win 2000 Win XP amp Mac 10 1 up Package Contents gt USB 2 0 4 Port Hub gt USB 2 0 Cable gt A Switching Power Adapter gt User Manual Specification Four downstream ports and one upstream port FCC regulations for home or office use CE emissions Self Power 5V 2 5A Adapter Input 100 240v 50Hz 60Hz Output 5V 2 5A Storage Temperature 10 85 C Working Temperature 0 40 C Supported O S USB 2 0 4 Port Hub a Se O o Win 98SE Build in O S Follow system driver Buildin OS Remark If you connect this hub to PC or Mac which system USB port PCI card or hub 2 is version 2 0 it will ask for the system s USB 2 0 driver Software Installation After you connecting this hub to PC by a USB 2 0 cable the system will detect the device and install the required drivers automatically E Windows System After completing the installation of the USB 2 0 4 Port Hub go to My Computer and right click to select Properties Then click the Device Manager tab and select Universal Serial Bus Controllers to find General Pu
3. e bottom of the hub between the stand off Make sure you here aclick You could push the stand in from the left or the right Refer to Figure 3 C Fastening Magnetically You can secure the USB 2 0 Hub on the computer table or steel frame Figure 4 7 Screw Figure 5 fn Hub Ea i Bottom Magnet Pa ma ae ete i Magnet MA k U shaped vr m m N Metal its a zumda Screw tT Ep rid Bottom Magnet l i Stand cane rd Bottom J e G S Magnet U shaped metal Ly 1 Please follow these figures in order and 2 Fasten the magnet on the stand and place use the screw that comes with the hub the stand in the hub and attach the stand to Refer to Figure 4 the desk or steel frame Refer to Figure 5 Note To eliminate data loss do not place disks next to or on this device D Fastening with Screws Figure 6 y 1 Secure the stand to the desk and fasten the F 44mm screws on both side of the stand Screw E oi x Package doesn t include screws for the desk J LP 2 Slide the USB 2 0 Hub into the stand Do the ae P same for both vertically and horizontally X A Desk Sy placed hubs Refer to Figure 6 1 USB 2 0 4 Port Hubs also can be stacked together with our USB 2 0 7 Port Hub therefore you can use both the seven and four port hubs together for your convenience 2 When you slide in the hubs in a stack face them in the same direction Refer to Figure 7 3 Slide the hubs
4. inward until you hear a click Do not stack hubs in opposite directions Certificate FCC Certificate This equipment has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation CE Certificate This equipment is in compliance with the requirements of the following regulations EN 55 022 CLASS B CE Fe DISCLAIMER Information in this document is subject to change without notice The manufacturer does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage including but not limited to special incidental consequential or other damage No part of this document may be reproduced or transmitted in any form by any means electronic or mechanical including photocopying recording or information recording and retrieval systems without the express written permission of the manufacturer
5. rpose USB 2 0 Hub Highlight that then go to the Property icon and check the Device Status make sure it read This device is working properly E Macintosh System After completing the installation of the USB 2 0 4 Port Hub open Apple System Profiler and click Devices and Volumes to view the names of attached USB 2 0 devices Verify that the device has been detected by locating its name in the Apple System Profiler Hardware Installation 1 Plug the included AC power adapter into the power jack at the rear of the USB 2 0 4 Port Hub and an electrical outlet 2 Plug the B type connector into the upstream port 3 Plug the A type connector into a computer or USB 2 0 Hub downstream port 4 Connect USB 2 0 devices or Hubs to the 4 Port Hub s downstream 4 ports Front View Rear View Power LED Red Upstream Port Status LED Green Downstream Power Jack Port LED Indicators The 4 Port 1Stack USB 2 0 Hub is equipped with LED indicators E LED Indicator red The indicator lights up red when the USB 2 0 Hub is receiving power from its external power source E LED Indicator green Each port has one status LED When the LED is on the downstream port means it is ready to use Over Current Status USB Hub Current Limit Exceeded The USB Human Interface Device has exceeded the current limits of its hub port The placement of the device is highlighted in bold type When the current limit e
6. xceeded E e USE Root Hub 2 ports g Unused Fort Generig WSR Hut lt i USB Human Interface Device Recommendation Disconnect the device and then click Reset to re enable the port IF you happen the over protection will disconnect power from the related port by turning off the green LED A pop up USB 2 0 Hub Current Limit Exceeded window will click Close a reboot will be required to regain the port appear Please click Reset to resume work or you can reset the hub by unplugging the USB 2 0 cable and plugging it back Using the USB Hub Stand There are 4 ways to set up this USB 2 0 Hub stand Either vertically horizontally fastening magnetically or fastening with screws Furthermore it is stackable with USB 2 0 7 Port Hub as well Stand and Magnet A Vertically Figure 1 Short Stopper 1 Push the USB 2 0 Hub from A all the way down until you meet the stopper Refer to Figure 1 B Horizontally Figure 3 Stand Bottom l Stand off Stand off i Stopper Stand off Magnet Of ii U shaped metal Screws Figure 2 Track A Bottom g Track Long Top Cover Track Clipper Clipper 2 Push the USB 2 0 Hub all the way in until you hear aclick There is a track on both the top and the bottom so you can put it either way depending on your situation Refer to Figure 2 1 Have the bottom of the stand facing up and push the stand to th
Download Pdf Manuals
Related Search