User Manual
Contents
1. FAR Light Source User Guide Cui Ultima Light Source Models Covered by this manual UFO 250 UG UFO 250 UP UFO 250 UGC UFO 250 UPC UFO 250 UGCF UFO 250 UPCF UFO 250 UGCFF UFO 250 UPCFF UFO 250 UGCS UFO 250 UPCS UFO 250 UGCFS UFO 250 UPCFS UFO 250 UGCSS UFO 250 UPCSS Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Issue 2 Revised 10092013 Tel 44 0 1890 883416 Fax 44 0 1890 883062 www fibreopticlighting com INTRODUCTION Thank you for purchasing this UFO light source Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference A high performance 250W metal halide light source for ultimate brightness which can be fitted with a choice of wheels for decorative lighting effects We do not recommend that the light source be left on for 24 hours a day 7 days a week as lamp life will be impaired A switch off of 30mins per day is recommended IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED Do not operate without complete lamp enclosure in place or if lens is damaged KEEP HARNESS IN PLACE WHEN IN OPERATION CAUTION Hot surface Keep away from curtains and other combustible materials WARNING RISK OF FIRE INJURY TO PERSONS Keep away from combustibles Unplug to cha2. A 70 Glass 72 PMMA lamp life as stated by manufacturer in optimum conditions Universal Fibre Optics a0 UNIVERSAL FIBRE OPTICS Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Tel 44 0 1890 883416 Fax 44 0 1890 883062 www fibreopticlighting com
3. air to circulate and prevent overheating The location must have free ventilation a Ultima Light Source Range INSTALLATION GUIDE Continued CONNECTION There are 2 main connections required the fibre port and the mains power supply Connect and secure the fibre optic connector to the fibre port before connecting the electrical supply Never run the light source with the fibre connector unplugged For separate feed units there will be additional power connections required OPERATION After installing and connecting the light source as described above all you have to do is turn the power on The lamp will take 3 4 minutes to reach full brightness This is normal for this type of light source If no light is produced please consult the TROUBLESHOOTING section in this manual Universal Fibre Optics fe MAINTENANCE LAMP REPLACEMENT Recommend Lamp change every 12 months for Metal Halide Lamps should not be run to the end of their life 1 Disconnect the light source from the power supply and allow to cool for 10 to 15 minutes 2 Remove the cover A from the light source 3 The lamp is located near the rear of the light source To free the lamp from its holder gently pull the lamp forwards B DO NOT unscrew the brass holder C as this will impair the light output 4 Dispose of the old lamp carefully 5 Fit the new lamp D DO NOT touch the lamp glass as this may cause it to EXPLODE If you do carefully cle
4. an it with a lint free cloth and alcohol 6 Replace the lid and reconnect to the power supply FUSE REPLACEMENT 1 Unplug unit from electrical supply and allow to cool 2 The fuse is located in a drawer under the mains input connector There is also a spare fuse located in this drawer 3 Open the fuse drawer 4 Withdraw fuse from its holder 5 Replace with identically specified fuse see specification table in this manual 6 Close the fuse drawer and power up the light source E Ultima Light Source Range MAINTENANCE Continued CLEANING THE UNIT Disconnect unit from power supply and allow to cool before attempting any cleaning of the unit A visual check of the unit should be completed every 12 months However cleaning should take place as and when required The body of the unit can be cleaned with a soft damp cloth do not use any abrasives on the unit The fans and vents should be kept clear by periodically blowing them out with compressed air Glass filter to be cleaned with soap and water then dried Please note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This must be DATED for warranty purposes Maintenance Undertaken Universal Fibre Optics D TROUBLESHOOTING Problem Probable cause s Remedy Unit is completely dead Main fuse blown Check and replace fuse Lamp and LED power indicator are not illuminate
5. ce Keyhole slots are provided on the base of the unit to allow for securing to a surface The light source is only suitable for use in a dry area If the unit is being mounted at a higher than the ground level block access below the work area before installing Verify that any screws or bolts can safely bear the weight of the light source Universal Fibre Optics INSTALLATION GUIDE Continued Verify that the supporting structure can safely bear the weight of all installed units cables and any other equipment For horizontal mounting it is recommended that the light source is secured to a solid surface using 4 x M4 or M5 screws or bolts and the keyhole slots This is particularly important if the light source location is not at ground floor level To mount the light source vertically first securely install 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened To mount the light source under a surface first securely install 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened CLEARANCE VENTILATION It is imperative that a gap of 300mm or more is left around the unit This is to allow
6. d Check that power is switched on and power supply is plugged in Allow unit to cool for 5 to 10 minutes Thermal switch activated and investigate reason for overheating No power to unit LED power indicator amp fan are on but no light is output Check plug connection ensure lamp is properly seated in its holder and the pins are fully mated Lamp needs replacing Replace lamp Lamp wires are not connected Unit needs cleaning Clean reflector and glass lens Poor light output Incorrect power supply Ensure power supply is 240VAC 50Hz Ensure fibre port connector is plugged in correctly and that the screw is tightened up properly Fibre port connector not plugged in correctly Allow unit to cool for 5 to 10 minutes Unit is overheating and investigate reason for overheating Check power is switched on and unit No power to separate is plugged in feed Decorative wheel not Check and replace fuse if necessary and Check and replace fuse if necessary fuse if necessary turning on separate electrical feed models Lamp going on amp off randomly Motor faulty Replace motor Please complete troubleshooting procedures before returning unit to us for further investigation gt Ultima Light Source Range TECHNICAL SPECIFICATIONS Description Ultima 250W Sunon DP200A or Adda AA1282HS AT amp Papst 8550N Philips MSD250 2 Glass BLV MHR 250N PMMA c 3000h Glass c 5000h PMMA 8500K Glass 4200K PMM
7. for the unit before powering it up e Always ensure that the unit is properly EARTHED Do not expose the unit to rain or moisture e Keep away from all combustible materials e Never attempt to tamper with the wiring or other internal components e Keep the unit away from gas oil and any other flammable or explosive materials Universal Fibre Optics LIGHT SOURCE LAYOUT Item Description Mains Input Socket Fuse Drawer Power Indicator Light 4 Cooling Fan 5 Separate Feed Power Inputs 6 Fibre Port Motor Covers 8 o 4 x Access Screws S 4 x Mounting Holes al Ultima Light Source Range INSTALLATION GUIDE In order for the Ultima light source to function safely and efficiently it must be installed according to this user manual Please read all sections thoroughly before switching on the light source POWER SUPPLY REQUIREMENTS Before plugging in the unit please make sure that the supplyis correct Failure to do so could cause the unit to malfunction The unit requires a 240VAC 50Hz supply and it MUST BE EARTHED The light sourceunits are provided with a cordset fitted with a standard plug UNIT MUST NOT BE DIMMED POSITIONING THE UNIT Standard horizontal mounting on shelf table Gy oe AS AA ee ee ca ea oe Vertical mounting fixed to wall Upside down mounting fixed to underside of shelf The light source can be mounted horizontally vertically or upside down on any flat surfa
8. nge lamp Do not touch lamp WARNING RISK OF FIRE Do not place lamp where the overhead surface is closer than 0 3m to the light source a Ultima Light Source Range IMPORTANT SAFETY INFORMATION INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted Lamp is HOT WARNING To reduce the risk of FIRE ELECTRIC SHOCK OR INJURY TO PERSONS 1 Unplug and allow to cool before replacing lamp 2 Lamp gets HOT quickly Only contact plug when turning on 3 Do not touch hot lens guard or enclosure 4 Do not remain in light if skin feels warm 5 Do not look directly at lighted lamp 6 Keep lamp away from materials that may burn 7 Use only with the correct lamp wattage as detailed on the serial label Failure to adhere to this will cause damage to the unit 8 Do not touch the lamp at any time Use a soft cloth Oil from skin may damage lamp 9 Do not operate product with missing or damaged guard lamp containment barrier lens or fibre optic harness 10 WARNING Lamp types are matched to the ballast and different wattages types cannot be used SAVE THESE INSTRUCTIONS e Always disconnect the unit from the power supply before opening or attempting to perform any work on it UNIT MAY GET HOT always allow unit to cool down before handling or moving it e Do not touch or attempt to remove the lamp while it is hot e Ensure that the power supply is correct
Download Pdf Manuals
Related Search