Home

LG New Wide Wired Remote Controller - LG Duct-Free

1. Function Pressure selection Zone state ESP standard value 01 V H Variable High 02 F H Fixed High 03 VL Variable Low 04 FPL Fixed Low Owner s amp Installation Manual 17 Installation instruction Installer Setting Remote Controller Master Sle Itis a function for settings in group control or 2 remote controller control If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure 2 If pressing button repeatedly it moves to master slave selection menu as picture below 3 Select Master Slave by pressing button 00 Slave 01 Master Mam U tu l Function Code Master Slave value 4 Press button to save mam ott 5 Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected Remote controller Function Indoor unit operates based on master remote controller at group control Master Master is set when delivering from the warehouse Setup all remote controllers except one master remote controller to slave at Slave group control k Refer to the group control pa
2. No Function Code Value 1 Test Run 01 01 Test Run Setup 2 Address Setting 02 00 FF Address of Central Control 3 SA Supply Air ESP 03 lt ESP level gt lt ESP value gt lt Example gt 01 Low 0 255 030i 5s 4 EA Exhaust Air ESP 04 02 High 03 Super High Function Code ESP step ESP value en 01 Normal 5 Product Direction 05 02 Opposite g ae 01 Supply Air First 6 Quick Refresh Priority 06 02 Exhaust Air First 5 00 Slave 7 Master Setting 07 01 Master A P 00 Slave 8 Override Setting 08 Oi Master 00 Auto Off 9 Dry Contact 09 01 Auto On 10 Release Of 3 Minute Delay 10 01 Set 01 Variable 11 Zone State ii 02 Fixed 12 Humidification for Singular 13 00 Not in Use Ventilation 01 Use 13 Humidification for Heat Mode 14 00 Automatic Ventilation 01 Manual Some contents may not be displayed depending on the product function 10 New Wide Wired Remote Controller Installation instruction Installer Setting Test Run Mode After installing the product you must run a Test Run mode For details related to this operation refer to the product manual 1 If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure Please cancel the right and left of wind direction for RAC product men tot dd Setup figure 01 blinks at the lower par
3. Press A V button to adjust AM PM setting won on eg Press K J button to Hour setting mode When the Hour icon flash please setting time The setting range is within 1 12 o i200 9 mon On itu x Press lt J button to shift to Minute setting mode When the Minute icon flash please setting minute the setting range is within 00 59 5 mIn o eo 48 New Wide Wired Remote Controller Owner s instruction Press button to exit After setup it automatically gets out of setup mode if there is no button input for 25 seconds K When exiting without pressing set button the manipulated value is not reflected If reservation is set turned on indication shows up at the lower part of LCD screen and air conditioner product runs at the time that is set If reservation is cancelled turned on indication disappears Owner s amp Installation Manual 49 Owner s instruction Programming OFF Reservation Automatically turned Off at reserved time that you set 1 2 Repeatedly pressing button to enter the OFF reservation setting mode segment flashing Press button Se Ex Setting OFF Reservation Time as AM 10 20 3 Press button to adjust AM PM setting o icid QE is 4 Press lt button to shift to Hour se
4. Temperature sensor selection Function 01 Remote controller Operation in remote controller temperature sensor 02 Indoor unit Operation in indoor unit temperature sensor Operation of higher temperature by comparing indoor unit s and wired Cooling remote controller s temperature 03 2TH There are products that operate at a lower temperature Heating Operation of lower temperature by comparing indoor unit s and wired remote controller s temperature The function of 2TH has different operation characteristics according to the product Owner s amp Installation Manual 15 Installation instruction Installer Setting Ceiling Height If pressing 3 button long for 3 z seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure If moving to ceiling height selection menu by pressing amp button it indicates as picture below _ lt Ceiling Height Selection Table gt Select ceiling height value by pressing A vy button 01 Low 02 Standard 03 High A Kk 2 Mv Function Code Thermistor setting Pressing button will exit settings mode 5 After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflec
5. Installation instruction If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure If moving to ceiling height selection menu by pressing 3 button it indicates as picture below _ 3 Select Zone State rate fixing mode by pressing v button 01 Variable 02 Fixed u RS itu it 2 t F lt Function Code Zone State fixing mode 4 Press button to save JS I I tut 5 Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected Owner s amp Installation Manual 21 Installation instruction Installer Setting Celsius Fahrenh This function is used for switching the display between Celsius and Fahrenheit Optimized only for U S A If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure Repeat pressing button to select Function code 12 20g II Function Code conversion mode value Ex Fahrengeit Setting Select Temperature unit mode by pressing button
6. 00 Celsius 01 Fahrenheit ieoi 0 Press button to exit or system will automatically exit after 25 seconds without any input k Whenever press degrees button in Fahrenheit mode the temperature will increase drop 2 22 New Wide Wired Remote Controller Installer Setting Option Function Se Installation instruction Setting feature for indoor unit when air cleaning heater humidifier Up down grill Ventilation KIT is newly installed or installed unit is removed If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure If pressing amp button repeatedly it moves to the selected option function code as picture below Function Code Plasma purification 20 Electric heater 21 Dehumidifier 22 eaha Elevation gii 23 Ventilation kit 24 Select existing condition a of each mode by pressing button lt gt vo 00 not installed z 01 installed mm out Function Code Existing condition Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected Owner s amp Inst
7. lt imnn On tin Owner s amp Installation Manual 43 Owner s instruction 7 Press lt button to move to Minute setting mode the Minute segment will flash immm O iittun is Setting Minute value by pressing button Press button to finish x msn o igi 1 0 In the process press button to release and exit from setting mode Aa In case of exit with incomplete information it will return to the previous setting 3 When exiting without pressing set button the manipulated value is not reflected 44 New Wide Wired Remote Controller Owner s instruction Function setting Auto Cleanin The method to setup Automatic Drying Cenas visame 1 Please press 3 button 2 Move to automatic drying menu by pressing button twice Automatic Drying icon will be displayed and the current status DISABLE will blink g D AE enanssa ae PE ma 3 If moving to ABLE icon area by using S GJ button ABLE icon blinks and automatic dry function is setup if pressing E button at that time G nE aed CAGED 4 When returning to automatic dry no use automatic dry function is cancell moving to DISABLE icon by pressing button and then pressing button
8. 5 If pressing button it gets out of setup mode K After setup it automatically gets out of setup mode if there is no button input for 60 seconds K When exiting without pressing set button the manipulated value is not reflected Automatic dry function might not be operated at the partial product Owner s amp Installation Manual 45 Owner s instruction Press button to enter the Programming mode the segment flashing Ex Setting Simple Reservation time as 3 button to adjust reservation 13 v s Press button to finish setting g Press button to exit X After setup it automatically gets out of setup mode if there is no button input for 25 seconds k When exiting without pressing set button the manipulated value is not reflected k When simple reservation setup product automatically runs or stops after the time that is set 46 New Wide Wired Remote Controller Owner s instruction Programming Sleep Reservation Sleep reservation is the function of air conditioner to run and stop after certain period of time at sleep mode before sleep When connected to a ventilation product and set the sleep reservation when it goes to the sleep mode after the set time has elapsed Press G button to enter the Programming mode Ex Setting Sleep Reservation time as 3 Repeat pressing button to enter the SLEEP reservation
9. reflected Press button to exit After setup it automatically Elevation grill function only operates in the indoor unit with the elevation grill 40 New Wide Wired Remote Controller x icon flash Press A M button to select active vane 1 2 3 4 All Standard Select Vane number using lt buttons Vane number No 1 2 3 4 all or standard Selected vane is in operation Please verify the operating vane To set the angle of all the vanes select all To set as the factory default settings select standard Select wind angle using and press button The boundary of wind angle settings can be changed to 5 levels or 6 levels according to the product When selecting standard for Vane number the wind angle does not move Set the wind angles for the remaining vanes as the same as above There are products with vanes with no 1 and no 2 only according to the product types Press button to exit K After setup it automatically gets out of setup mode if there is no button input for 60 seconds X When exiting without pressing set button the manipulated value is not reflected Press 3 button to complete and S active the setting process 7 Airflow direction function will be released whenever setting vane angle Press button to exit or system will automatically release without any input after 25 seconds O
10. 37 Owner s instruction Function setting Robot Cleaning Autoi Robot cleaning function is the function of cleaner attached to the product to automatically clean filter when using air conditioner for the specific period of time Set manual or automatic mode of smart cleaning 1 Press button repeatedly until the Gais flashing 2 When the e r flashing press E button to set clear this function Set state Enable Auto Smart Clean function x iors malo v oO AN N AE ale baad me P HL Clear state Disable Auto Smart Clean function Pa ah Lui silia 4 ry HL 3 When returning to manual robot cleaning manual function is cancelled if moving to manual icon by pressing Right Left button and then pressing button 4 Press button to exit After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected Robot cleaning function is an additional function of the product and might not be operated at the partial product 38 New Wide Wired Remote Controller Owner s instruction Function setting Filter Sign Clear This function is to clear the indicator of indoor filter cleaning Press button repeatedly until the is flashing Wh
11. ON OFF Weekdays Holidays Reservations Owner s amp Installation Manual 63 Owner s instruction Different mode drive i Different mode drive is a phenomenon taking place when indoor units drive mode is different in the case that a few indoor units are set up at one AHU Different mode drive doesn t show up at cooling exclusive model 1 While a few indoor units are running air cooling at one AHU it doesn t operate heating drive if one indoor unit operates heating drive 2 While a few indoor units are running heating at one AHU it doesn t run if one indoor unit runs cooling or humidity removal It is the indication that it is operating heating drive at AHU 3 If pressing button indoor unit automatically runs at the mode that different indoor units are running after about 5 seconds and operates 64 New Wide Wired Remote Controller Checkups before reporting breakdown i Please first check the items below for product s defects before consulting to service center Owner s instruction Is air conditioner s power on Please check up circuit breaker Please check up wire remote controller s setup condition It has no power Are air conditioner and remote Please connect air conditioner and remote on controller properly connected controller cable with cable Is cable connection correct Please check again referring
12. the information label inside of the l door Please choose proper language ial UC a oe ee teen ee 4 ROOM TEMPERATURE BUTTON SETTING CANCEL BUTTON B EXIT BUTTON Some functions may not be operated and displayed depending on the product type Accessory Connection Cable Screw Owner s Installation Inform label 1EA 10m 4 EA manual 8EA 8Languages 4 New Wide Wired Remote Controller Installation instruction D Installation instruction 1 Please fix tightly using provided screw after placing remote controller setup board on the place where you like to setup Please set it up not to bend because poor setup could take place if setup board bends Please set up remote controller board fit to the reclamation box if there is a reclamation box 2 Can set up Wired remote controller cable into three directions Setup direction the surface of wall reclamation upper right If setting up remote controller cable into upper and right side please set up after removing remote controller cable guide groove Remove guide groove with long nose Reclamation to the surface of the wall Upper part guide groove Right part guide groove lt Wire guide grooves gt Owner s amp Installation Manual 5 Installation instruction 3 Please fix remote controller upper part into the setup board attached to the surface of the lt Connecting order wall as the picture below and then connec
13. to setup method at the manual Di rrectly setup time Plea t up current time correctly Itdoesn t operate Meee cue F e elated eae reservation drive Did you correctly make a Please set up again referring to the reservation manual It doesn t release Is desired temperature setup Please set up desired temperature lower cool wind lower than current temperature than current temperature Air conditioner Isn t reservation drive setup Please cancel reservation drive automatically runs or stops Erroris indicated ff Does remote controller indication Please check again wire remote on remote window indicate CH03 controller s setup condition controller Please check again connection condition indication window of air conditioner and remote controller cable Owner s amp Installation Manual 65 66 New Wide Wired Remote Controller Owner s amp Installation Manual 67
14. want independent cleaning air drive please setup cleaning air by pressing additional drive button at ventilation drive 32 New Wide Wired Remote Controller Owner s instruction Sub function Humidifier Only products with humidifying function can use this 1 Repeatedly pressing button 8 until amp icon flash 2 Turn on off HUMIDIFIER by pressing E button The amp icon will be displayed in case of male SETTING option and disappear a ko in reverse case Press button to exit X After setup it automatically gets out of setup mode if there is no button input for 25 EJ seconds amp When exiting without pressing set button the manipulated value is not Humidification function might not be operated at the partial product Owner s amp Installation Manual 33 Owner s instruction Sub function Electric Heater It is a function to strengthen the heating ability by turning on the electric heater during the heating operation It can only be set during heating operation Repeatedly pressing Ez button until amp icon flash Turn on off ELECTRIC HEATER by pressing Ga button the Wt icon will be displayed in case of SETTING option and disappear in reverse case Press button to exit K After setup it automatically gets out of setup mode if there is no button input for 25 seconds 3k When exiting without pressin
15. 2547 1007 22 2 core 3 shield 5 or above 6 New Wide Wired Remote Controller Installation instruction Group control 1 When installing more than 2 units of air conditioner to one wired remote controller please connect as the right figure If it is not event communication indoor unit set the unit as slave Check for event communication through the product manual GND Signal wire controller you must change the master slave setting from the indoor unit Indoor units the master slave configuration of the product after completion of indoor unit power OFF and then ON the power after 1 minutes elapsed sign up For ceiling type cassette and duct product group change the switch setting of the indoor PCB ON i i siete ale al 1 2 3145 678 3 switch OFF Master Factory default setting For wall mount type and stand type product change the master slave setting with the wireless remote controller Refer to wireless remote controller manual for detail When installing 2 remote controllers to one indoor unit with event communication function set the master slave of the remote controller Refer to remote controller master slave selection When controlling the group some functions excluding basic operation setting fan level Min Mid Max remote controller lock setting and time setting may be limited 2 When installing more than 2 wired remote controllers t
16. It will cause fire or electric shock Sub function Humidifier or explosion or injury or explosion or injury Sub function Electric Heater Sub function Energy Saving Cooling Operation Sub function Robot Cleaning Manual Setup H in use Function setting Child Lock Function setting Robot Cleaning Automatic Setup Do not place flammable Do not allow water to run Do not give the shock to the Function setting Filter Sign Clear stuffs close to the product into the product product Function setting Elevation Grill 7 5 F F F Function setting Vane Angle Control It will cause fire It will cause electric shock or It will cause breakdown when Function Setting Change Temp breakdown giving the shock to the product Function setting Changing Current Time Function e E Ato peang Request to the service center or installation Do not give the shock using sharp and Simple Reservation Fi Programming Sleep Reservation specialty store when the product becomes wet pointed objects ON Reservation It will cause fire or electric shock It will cause breakdown by damaging parts OFF Reservation Programming Weekly Reservatior Programming Holiday Reservation ACAUTION Ventilation Product User Manual Interlinked Air conditioner and Ventilation H in use Ventilation Product User Manual Interlinked operation with general ventilation Manual Conversion Pressing Ventilation button in venti
17. Please move to AM PM setup part Weekly aes MON TUE WED THU FA SAT of turning on by using A V button gt A HeT am ON B SS eae WEEKLY es WED THY FRI SAT l 2 areal LAT Oo ON E amp cate je Ri Cc SG J q E 2 KW 2 G Gea 5 1 2 If finishing weekly reservation setup please press setup cancellation button Weekly reservation setup for the day that you set is finished Please move to hour setup part of WEEKLY SAMON TUE wen THY SAT A turning on by using K button atl GG on It is the part to setup the time at a ae which air conditioner is turned on weekly os wales vy FA SAT TI IEn F Please change time by using button You can setup hour 0 12 Please move to minute setup part of turning on by using 5 button If minute indication blinks please setup minute by using button 52 New Wide Wired Remote Controller 1 3 If you setup with the method identical with above by selecting the day that you d like to setup it operates weekly reservation If you setup both turning on reservation time and turning off reservation time identically it doesn t operate reservation drive Weekly reservation explanation v SUN MON TUE WED THU FRI SAT Law peas Reservation number Turning on time Turning off time v SUN MON TUE WED THU FRI SAT Under bar the indication that there is weekly reservation for correspondi
18. Release part for Filter Cleaning function Refer to Function Settings Time Settings part for Time Setting function Refer to Function Settings Temperature Conversion part for Temperature Conversion function Owner s amp Installation Manual 61 Owner s instruction Ventilation Product Reservations Setti Sleep Reservations Sets to operate ventilation lightly during the sleep 1 Press button to enter the reservation settings mode 2 Press button again to move to Sleep Sleep icon blinks and the reservation time is displayed Use button to set the reservation time Reservation time can be set between 1 12 hours mr Hr Li ry Hr ry Hr LUO P cm 5 Pressing button will exit the settings mode If no button input for 60 seconds after the setting it exits the settings mode automatically 3k When exiting without pressing set button the manipulated value is not reflected When the reservation is set Sleep is displayed at the bottom of LCD screen om 1200 4 When Sleep reservation dale is finished press z SLEEP When the reservation is cancelled Sleep mark disappears 6 When the sleep reservation setting is finished it operates lightly for the set time Simple ON OFF Weekdays Holidays Reservations Please refer to the Reservation Setting
19. allation Manual 23 Owner s instruction F Owner s instruction Standard Operation Standard Ci It cools the room by comfortable and clean wind 1 Press button to turn on the indoor Press button to select Cooling operation mode 3 Adjust the desired temperature by pressing buttons _ Press gt button to check the Room temperature When setting the desired temperature higher than room temperature only ventilation wind is blow out instead of cooling wind Setting Temp Range 18 C 30 C 64 F 86 F 24 New Wide Wired Remote Controller Owner s instruction Standard Operation Power Coolit It makes the room cool using pleasant and fresh air quickly 1 Press button to trun on the indoor 2 Press f button to select B cooling operation mode X er Press s button continuously x until Po displayed What is Power Cooling Desired temperature Po actually 18 C It make room temperature Wind flow power wind drop fast by running Wind direction fix to air cooling position Partial product has no power air cooling function Standard Operation Heating Mo It supplies warm wind to the indoor 1 Press button to turn on the indoor Press button to select Heating mode T To check the indoor temperature o
20. ash Turn on off Smart Clean function by pressing K When the cleaning is finished the smart cleaning display disappears automatically K To cancel robot cleaning manual setup function you move to power saving menu by pressing 3 button and then if pressing utton robot cleaning icon disappears and the function is cancelled 3 36 New Wide Wired Remote Controller After setting press button to exit X Robot cleaning manual setup function might not be operated at the partial product 3k When exiting without pressing set button the manipulated value is not reflected 1 Owner s instruction Function setting Child Lock It is the function to use preventing children or others from careless using Press button repeatedly until the amp is flashing If moving to setup icon area by using button setup icon blinks and child lock function is setup if pressing button at that time 3 When cancelling lock function if moving to cancel icon by pressing lt button and then pressing button child lock function is cancelled 4 Press button to exit K After setup it automatically gets out of setup mode if there is no button input for 25 seconds 3 When exiting without pressing set button the manipulated value is not reflected Owner s amp Installation Manual
21. button 2 Press Ventilation button on the wired remote controller and enter Ventilation For example when you setup control mode to check the operation of ventilation product Monday Friday to holiday Monday Friday letter disappears Please press button if finishing holiday setup If it comes to appointed holiday air conditioner automatically stops Once you setup holiday appointment until before you cancel holiday setup 3 To convert back to air conditioner mode press Ventilation button at the air conditioner automatically stops ventilation mode within one hour even though you run If no button pressed for 15 seconds or more at ventilation mode it automatically converts back to air air conditioner conditioner mode Ventilation product represent general ventilation product and direct expansion ventilation product 54 New Wide Wired Remote Controller Owner s amp Installation Manual 55 Owner s instruction Ventilation Product User Manual Interlinked operation with It is used when air conditioner is interlinked with ventilation product It is a function that cools and refreshes indoor air using the ventilation product at the same time operating the air conditioning function Ventilation interlinked operation Press button on the remote controller control panel Itis only used when air conditioner a
22. ditioner is stopped 3 Pressing button will change operation mode Pressing the button will convert from cooling gt eating gt automatic gt stop Pressing button in ventilation mode changes the strength of wind a Pressing the button can select from weak gt strong gt very strong Cooling heating operation selection and the desired temperature can be adjusted in direct expansion type ventilation single operation Refer to the basic operation temperature adjustment for changing desired temperature Owner s amp Installation Manual 59 Owner s instruction Ventilation Product Additional Operations Fast It is a function to operate ventilation function more efficiently through the ventilation additional functions fast power saving settings Fast ventilates fast It converts in the order of fast gt power saving in ventilation mode Fast is blinking on the display and pressing E button will stabilize fast icon and the function is set RE m XE ne H x H ai vast PFN 3 Pressing button will exit the settings Power Saving efficiently ventilates and performs power savings It converts in the order of fast gt power saving in ventilation mode 2 Power Saving is blinking on the display and pressing button will stabilize Power Saving icon and the
23. e the button is pressed it changes from Heat exchange gt normal gt automatic The display on the remote controller displays only when it is in ventilation mode and when it converts to air conditioner mode it displays the desired temperature DAK 1 button on the remote controller It displays as the figure right side in the direct expansion type ventilation single operation Pressing a button in ventilation mode changes the strength of wind Pressing the button can select from weak gt strong gt very strong Changing back to air conditioner mode 1 Automatic Conversion when no button is pressed for 15 seconds or longer it automatically converts back to air conditioner mode 2 Manual Conversion Pressing button in ventilation mode will manually convert 58 New Wide Wired Remote Controller 2 Pressing button will change the ventilation mode Pressing the button converts from heat exchange gt normal gt automatic ntitation Remote Controller mode Display Heat exchange Directh ilate inde jthout goir Nomai SE a wet cong Circulate indoor air with automatically comparing indoor and outdoor air Contents Circulate indoor air without loss of heat Automatic The 88 segment display above is only displayed when it is in direct expansion type ventilation single operation and the air con
24. en the W is flashing press the to clear this display When filter is covered by dust it will reduce cooling heating efficiency and accumulate more electric power Therefore do clean the filter whenever cleaning time is expired Filter cleaning indication is automatically cancelled without the separate cancellation after certain period of time Owner s amp Installation Manual 39 Owner s instruction Function setting Elevation Grill This function is to move the indoor filter up down for cleaning filter Owner s instruction Function setting Vane Angle Cor This function is to adjust angle at which airflow is blow out 1 Repeat pressing button until 1 Press amp button Repeat pressing button until icon flash Move to descent using and press button will display descent icon and the up down grill will descent When up down grill descents to the desired position move to stop icon suing lt J button and press button to stop up down grill When filter cleaning is finished fix the filter to the up down grill move to ascent icon using lt gt button and pres button to ascent up down grill gets out of setup mode if there is no button input for 60 seconds When exiting without pressing set button the manipulated value is not
25. function is set ims RE RE FAN SPEED SOEH l H 3 Pressing button will exit the settings General ventilation and direct expansion ventilation have the same additional functions Ventilation Heater Humidifier additional function settings are the same as air conditioner 60 New Wide Wired Remote Controller Owner s instruction Ventilation Product Function Settings _ Delay Time It operates after delay time in ventilation operation 1 Press Settings button 2 Pressing button repeatedly will move to the delay time menu Then delay time icon is displayed and the m Lt mmc a gt pa ee a a E 3 Pressing A V button will change the delay time settings Boundary of delay time settings 00 60 minutes in the units of 1 minute 4 When the desired delay time is displayed press button to finish the settings 5 Press Gj button when the setting is finished K If no button input for 1 minute after the setting it exits the settings mode automatically When exiting without pressing set button the manipulated value is not reflected Lock Filter Cleaning Time Setting Converting Temperature Refer to Function Settings Lock Settings part for lock function Refer to Function Settings Filter Cleaning Display
26. g set button the manipulated value is not reflected Heater function is additional function and it might not be operated at the partial product 34 New Wide Wired Remote Controller Owner s instruction Sub function Energy Saving Cooling OJ o Power saving air cooling function is the function to improve use s comfortableness and power saving capacity by adjusting desired temperature while running air cooling 1 Repeatedly pressing button aA until icon flash ER 2 Operate or cancel Energy Saving amp function by pressing button To cancel power saving function you move to power saving menu by pressing button and then if pressing button power saving icon disappears and the function is cancelled Press button to exit lt After setup it automatically a gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected Power saving function is possible to setup only when running air cooling Power saving function might not be operated at the partial product Owner s amp Installation Manual 35 Owner s instruction Sub function Robot Cleaning Mani Robot cleaning function is the function for cleaner attached to the product to automatically clean the filter when using air conditioner for the specific period of time 1 Repeatedly pressing until icon fl
27. he user does not follow the mandatory items it may cause personal injury or property Installer Setting Ceiling Height Selection damage Installer Setting Static Pressure Settin f n i P Installer Setting Remote Controller Master Slave Setup Q Warning and Caution are to call the user s attention to the possible danger Read and follow Installer Setting Override Master Slave Setting them carefully in order to prevent a safety accident Installer Setting Dry Contact Mode Setting Warning and Caution are indicated in this guide and the product itself to help protect the users Installer Setting Zone State from danger Installer Setting Celsius Fahrenheit Installer Setting Option Function Setting Owner s instruction Standard Operation Standard Cooling Standard Operation Power Cooling Standard Operation Heating Mode Standard Operation Dehumidification Mod AWARNING E Installation Standard Operation Fan Mode Be sure to request to the Request to the service center Do not disassemble fix and aia oe 5 Ae E a service center or installation or installation specialty store modify products randomly Standard Operation Airflow Setting specialty store when when reinstalling the Sub function Direct wind indirect wind installing products installed product Sub function Plasma Purification It will cause fire or electric shock It will cause fire or electric shock _
28. inks on the display and then if pressing button direct indirect wind icon is removed and the function is cancelled If pressing G button it gets out of setup mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected mc e ibe Am A direct wind me EAE indirect wind Direct indirect wind function is additional function and it might not be indicated or operated at the partial product Direct indirect wind function is possible only when product is running Owner s amp Installation Manual 31 Owner s instruction Sub function Plasma Purification Only products with humidifying function can use this The method to setup cleaning air 1 Repeat pressing button until icon flash 2 Operate or cancel Plasma Purification function by pressing E button icon appears disappears on display part up to selection 3 After setting press button to exit a After setup it automatically gets out of setup mode if there is no button input for 25 seconds k When exiting without pressing set button the manipulated value is not reflected Cleaning air function is additional function and it might not be indicated or operated at the partial product Cleaning air function is possible only when product is running If you
29. instruction Installer Setting Dry Contact Mode Dry contact function is the function that is possible to use only when dry contact equipment is separately purchased setup 1 If pressing 3 button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure 2 If pressing button repeatedly it moves to remote controller dry contact mode setup menu as picture below 3 Select Dry contact setting by A Vv pressing button 7 00 Automatic 01 manual m gg UJI I Ci C ie Function Code Dry Contact setting value button to save 3 4 Press OG i 5 Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds k When exiting without pressing set button the manipulated value is not reflected gt What is Dry Contact Like hotel card key and body perception sensor it is the signal of the point of contact when using air conditioner by interlocking Please refer to dry contact manual for more details 20 New Wide Wired Remote Controller Installer Setting Zone State It is the function to setup indoor unit s wind flow to variable or fixed Variable Comp ON setup airflow Comp OFF weak wind Fixed Comp ON setup airflow Comp OFF setup airflow
30. it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure 2 If entering into ESP setup mode by using button it indicates as the picture below He i nn wou wud UT ae T Function Code ESP value Function code ESP code 3 ESP value Select ESP fan step by pressing button 01 very low 02 low 03 medium 04 high 05 power Gabi K 4 e Move to ESP value setting by pressing gt button It is 000 when delivering A from the pa x Gani a HH H 5 Press f a button to setup ESP value It is possible to setup ESP value from 1 to 255 and 1 is x the smallest and 255 is the biggest Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected When setting ESP value on the product without very weak wind or power wind function it may not work 12 New Wide Wired Remote Controller Owner s amp Installation Manual 13 Installation instruction 6 Select ESP fan step again by using button and setup ESP value as No 4 and 5 that corresponds each wind flow Press button to save 8 Press button to exit K Afte
31. lation mode will manually conve Do not clean using the Do not press the screen Do not touch or pull the lead Ventilation Product User Manual Interlinked Operation with Direct Expansion Ventilation powerful detergent like using powerful pressure or wire with wet hands Ventilation Product User Manual Single Operation with Direct Expansion Ventilation Ventilation Product Additional Operations Fast Power Saving solventbutuse softiciothsi selectitwojbuitons Ventilation Product Function Settings It will cause fire or product It will cause product breakdown or It will cause product breakdown or Ventilation Product Reservations Settings deformation malfunction electric shock Ventilation Product Installer Setting Functions Entering Method Different mode drive Checkups before reporting breakdown 2 New Wide Wired Remote Controller Owner s amp Installation Manual 3 Part Description J Part Description Name and Function of Remote Controller OPERATION INDICATION SCREEN SET TEMPERATURE BUTTON FAN SPEED BUTTON ON OFF BUTTON OPRATION MODE SELECTION BUTTON WIRELESS REMOTE CONTROLLER RECEIVER Some products don t receive the wireless signals AIR FLOW BUTTON SUBFUNCTION BUTTON FUNCTION SETTING BUTTON D VENTILATION BUTTON RESERVATION B UP DOWN LEFT RIGHT BUTTON To check the indoor temperature press gt button Please attach
32. nd general ventilation is interlinked Interlinked operation displayed on the remote controller display Pressing Start Stop button at ventilation mode will start ventilation 56 New Wide Wired Remote Controller Pressing button will change the za ventilation operation mode Pressing operation selection button will change the mode in the order of Heat exchange gt normal gt automatic It only displays on the remote controller display when it is in ventilation mode and it displays the desired temperature when it returns to air condition mode Pressing button in general ventilation mode will change airflow speed Pressing airflow speed button will change the mode in the order of weak gt strong gt extra strong If CO2 sensor is installed it can select from weak gt strong gt very strong gt automatic Changing back to air conditioner mode 1 Automatic Conversion when no button is pressed for 15 seconds or longer it automatically converts back to air conditioner mode 2 Manual Conversion Pressing 3 button in ventilation mode will manually convert Owner s instruction Ventilation single operation 1 Press button on the remote controller 2 Pressing button will change the ventilation mode Ventilation Remote Controller Tode Display Contents Heat exchange Ci
33. ng day Owner s amp Installation Manual 53 Owner s instruction Owner s instruction Ventilation Product User Manual Interlinked Air conditioner ai Programming Holiday Reservatio It automatically stops at reserved day that you set 1 Control using remote controller where air conditioner indoor unit and the ventilation product is installed at the same time Please press button Single Operation Interlinked Operation It enters into reservation General Ventilation Single Operation General Ventilation Interlinked Operation setup mode p ID ceneral A Air conditioner gf T General General lt Indoor unit Ventilation Please move to holiday by repeatedly Ventilation Ventilation Wired Remote Wired Remote Controller Controller te Direct Expansion Ventilation Single Operation Direct Expansion Ventilation Interlinked Operation Please move to date that re Direct Direct Expansion Air conditioner Direct you want to setup holiday Expansion Ventilation Indoor unit s penn by using lt J button Ventilation PRIETA AIM ired Remote SUN WON TUE WED THU FRI SAT Controller t Vili SUN MON TGE WED FHU FRI SA n PERT aai FFS Connecting wires is the same as air conditioner user manual Refer to page about Group control Wired Remote Controller Please appoint or cancel holiday by using A Y or E3
34. ng mode doesn t work if desired temperature is lower than room temperature Please increase the desired temperature Room Temperature Check ECD B a 1 Whenever press button the room temperature will be displayed within 5 seconds After 5 seconds it turns to display the desired temperature Because of location of remote controller the real room temperature and the this displayed value can be different For air cooling drive from 18 C to 30 C and for heating drive from 16 C to 30 C you can select desired temperature 5 C is proper for the difference between room and outside temperature 28 New Wide Wired Remote Controller Owner s amp Installation Manual 29 Owner s instruction Sub function Direct Wind Ina It is the function to directly or indirectly control wind direction by body perception sensor The method to setup direct indirect wind 1 Please press B button Owner s instruction The method to cancel direct indirect wind 1 Please press button 2 The icon of direct indirect wind blinks on the display and then if pressing button direct indirect wind icon is fixed and the function is setup ED ppa E direct wind KPN indirect wind a 30 New Wide Wired Remote Controller If pressing Gq button it gets out of setup mode AY The icon of direct indirect wind bl
35. o one air conditioner please connect as the right picture When installing more than 2 units of wired remote controller to one air conditioner set one wired remote controller as master and the others all as slaves as shown in the right picture MASTER SLAVE You cannot control the group as shown in the right for some products lt When simultaneously connecting Refer to the product manual for more detail 2 sets of wired remote controller gt When controlling in groups set the master slaver of the remote controller Refer to Installer setting section on how to set master slave for more detail Owner s amp Installation Manual 7 Installation instruction Installer Setting How to enter ACAUTION Installer setting mode is to set the detail function of the remote controller If the installer setting mode is not set correctly it can cause problems to the product user injury or property damage This must be set by an certificated installer and any installation or change that is carried out by a non certificated person should be responsible for the results In this case free service cannot be provided 1 If pressing button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure When you enter the setting mode initially Function code is displayed on
36. perature A Increase 1 C or 2 F per one time pressing M Decrease 1 C or 2 F per one time pressing 1 Please setup desired wind eal powerfulness by wind powerfulness button Every time you press wind z powerfulness you can select the wind flow in o order of feeble gt weak gt weak medium gt medium gt medium strong gt strong gt power Oo gt automatic The menu item might not be partially selected according to product function Please refer to product manual for product s detailed function g Room temp Indicate the current room temperature Set temp Indicate the temperature that user want to set Depend on what kind of controller the desired temperature can be adjusted at 0 5 C or 1 F Wind direction You can simply adjust desired wind direction Cooling operation The cooling mode doesn t work if desired temperature is higher than room temperature Please lower the desired temperature Please set desired wind direction by pressing i button You can select wind direction of comfortable wind gt Up Down and Right Left gt Right Left gt Up Down by pressing js button Partial item of wind directions might not be selected according to product function Please refer to product manual for product s detailed function Heating operation The heati
37. press the room temperature button Teme uo Adjust the desired temperature by pressing A buttons When setting the desired temperature lower than room temperature there is only ventilation wind Heating drive only operates at the cooling and heating model Heating doesn t operate at cooling exclusive model Owner s amp Installation Manual 25 Owner s instruction Standard Operation Dehumid It removes humidity while air cooling weakly 1 Press button to turn on the indoor 9 Press w button to select orn Dehumidification mode C The temperature setting can not be adjusted during operation this mode Press the button to select mn airflow rate feeble gt weak gt medium gt strong gt automatic The initial wind powerfulness of humidity removal drive is weak In rainy season or high humidity climate it is possible to operate simultaneously dehumidifier and cooling mode to remove humidity effectively The menu item of wind powerfulness might not be partially selected according to the product Standard Operation Fan Mode It blows the air as it is in the indoor not the cold wind Press button to turn on the indoor button to select Fan ones FAN 3 Every time pressing button you can select wind flow in order of s feeble weak medium st
38. r setup it automatically gets out of setup mode if there is no button input for 25 seconds K When exiting without pressing set button the manipulated value is not reflected Function code ESP code ESP value Please be careful not to change the ESP value for each fan step It does not work to setup ESP value for very low power step for some products ESP value is available for specific range belongs to the product 14 New Wide Wired Remote Controller Installation instruction Installer Setting Thermistor This is the function to select the temperature sensor to judge the room temperature If pressing amp button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure If moving to room temperature perception sensor selection menu by pressing button it indicates as picture below 3 Set Thermistor value by pressing button 01 Remote Controller 02 Indoor 03 2TH 4 t Function Code Thermistor setting button to save mum i 4d f 5 Pressing button will exit settings mode k After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected lt Thermistor Table gt
39. rculate indoor air without loss of heat Normal Directly circulate indoor air without going through heat exchanger Automatic Circulate indoor air with automatically comparing indoor and outdoor air 3 Pressing button will change the strength of the wind Pressing the button can select from weak gt strong gt very strong If CO2 sensor is installed it can select from weak gt strong gt very strong gt automatic Owner s amp Installation Manual 57 Owner s instruction Ventilation Product User Manual Interlinked Operation with Di It can only be used when the air conditioner is interlinked with direct expansion ventilation product Interlinked Operation with Direct Expansion Ventilation 1 Press button on the remote controller a Itis used only when air conditioner and the ventilation product are interlinked Interlinked operation displayed on the remote controller display Pressing It performs ventilation operation with cooling or heating at the same time using the heat exchanger inside the direct expansion type ventilation product Owner s instruction Direct expansion type ventilation single operation Pressing button in ventilation mode starts ventilation A secto TEMP Pressing sox button in ventilation mode will change the ventilation mode Every tim
40. rong automatic When running ventilation compressor of AHU doesn t work Ventilation drive does not release cool wind but general fan Because it releases the wind that has no temperature difference from the room it functions to circulate the inside air The menu item of wind powerfulness might not be partially selected according to the product 26 New Wide Wired Remote Controller Owner s instruction Standard Operation Auto Operati 1 Press button to turn on the indoor Press button to select fA Artificial intelligence Mode o PE You can adjust the temperature as the picture on the right for cooling and heating model 4 For the case of cooling exclusive as the picture on the right you can adjust the temperature from hot to cold from 2 to 2 based on 00 During operating Auto Operation mode We can use the FAN SPEED button We can change manually to other operation mode Owner s amp Installation Manual 27 Owner s instruction Owner s instruction Standard Operation Temperature Setting Room Standard Operation Airflow Set Wind powerfulness You can simply adjust Temperature Setting desired wind powerfulness 1 We can simply adjust the desired temperature Press the A v buttons to adjust the desired tem
41. rt for details When controlling in groups basic operation settings airflow strength weak medium strong lock setting of the remote controller time settings and other functions may be restricted 18 New Wide Wired Remote Controller Installer Setting Override Master Slave Override master slave selection function is since Multi V 7 series model the function to prevent product s different mode operation If it setup as the slave It blocks to change opposite run mode to outdoor unit cycle cooling heating Installation instruction If pressing amp button long for 3 seconds it enters into remote controller setter setup mode If pressing once shortly it enters into user setup mode Please press more than 3 seconds for sure If pressing button repeatedly it moves to override master slave selection menu as picture below Select Master Slave by pressing A v button 00 Slave 01 Master Hfz F Function Code Master Slave button to save Hth Pressing button will exit settings mode After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected K Override master slave selection function is possible to use only when it is connected to the succeeding models of Multi V 7 series Owner s amp Installation Manual 19 Installation
42. s part of the air conditioner for Simple ON OFF Weekdays Holidays Reservations 62 New Wide Wired Remote Controller Owner s instruction Ventilation Product Installer Setting Funct ACAUTION Installer setting mode is a mode to set the detail functions of the remote controller When the installer settings are not set properly it may cause the fault of the product injury to the user or damage to the property It must be set by a certified technician and when it is installed without certified technician or changed discretionally all of the problems are the responsibilities of the installer and we do not provide service free of charge 1 Press 2 button to enter ventilation mode F 2 Pressing button down for more than 3 seconds will enter the settings mode Pressing once shortly will enter the user settings mode You must press down for more than 3 seconds 3 When you enter the installer settings mode the data value that can be set is displayed at the lower right corner of LCD screen mi i LI Code Seting value value m f Some categories of the menu may not be displayed according to the function of the product or the menu name may be different Simple ON OFF Weekdays Holidays Reservations Please refer to the Reservation Settings part of the air conditioner for Simple
43. s wen gu en sar button Weekly blinks at this time 1 Gon Owner s instruction 1 Please move to AM PM setup part a O Tuono wads FR SAT of turning off by using gt button O nr AM PM setup is identical with HHN turning on time setup Tuan Suwon DSM MOTUS YEG S ee SSCA AM Tir L OFF LILLIE few oases PP OFF PM LILI Please select weekly reservation meen oS Sy yoy TUE ye Ty ERI SAT or weekly reservation by using aw in hg ON A button N E You can setup two reservations a pious PTU FSA weekly reservation 1 and weekly ham wri Tic N reservation 2 for a day Q Please move to date setup part by WEEKLY SAN TUE wen THY rn sa A e amp using S 5 button If date Ah I indication blinks please setup date You can setup date from Monday to Sunday AM 1 Please move to hour setup part fen oem i ina Ri WEEKLY SHOTS WET TALS of turning off by using Right TEE button eM Let It is the part to reserve the time WEEKLY oS pye WELS DEED at which air conditioner is 1 OFF turned off PM ALAI If hour indication blinks please setup hour K Please setup hour and minute WEEKLY SN VON UE pen THU ERI SA i i i rit po OFF identically with the method to ow GOGO setup turning on time _ WEEKLY OAE L OFF PM ict Ir
44. setting mode segment flashing Press button to adjust reservation time The SLEEP reservation time is from 1 to 7 hours ih Jh Ma ae button to finish setting Whenever reservation is done Press button to exit After setup it automatically gets out of setup mode if there is no button input for 60 seconds 3k When exiting without pressing set button the manipulated value is not reflected If reservation is setup sleep indication shows up at the lower part of LCD screen If finishing sleep reservation setup air conditioner product operates sleep drive and stops after the time that is set ACAUTION Please reserve proper time at sleeping Too much air cooling is not good for your health Because it automatically adjusts desired temperature for comfortable air cooling at sleep drive there could be difference between remote controller s desired temperature and air conditioner body s desired temperature Sleep reservation operates as off reservation for the product whose temperature adjustment isn t controlled by unit of 0 5 C Owner s amp Installation Manual 47 Owner s instruction Programming ON Reservation Automatically turned On at reserved time that you set Press button Ex Setting ON Reservation Time as AM 10 20 Repeat pressing button to enter the ON reservation setting mode segment flashing
45. t gt with setup board by pressing lower part Please connect not to make a gap at the remote controller and setup board s upper and lower right and left part Wall Wall Side Side gt When separating remote controller from setup board as the picture below after inserting into the lower separating hole using screw driver and then spinning clockwise remote controller is separated There are two separating holes Please individually separate one at a time Please be careful not to damage the inside components when separating lt Separating order gt Wall Side 4 Please connect indoor unit and remote controller using connection cable T Please check if connector is normally connected Indoor E Unit side Connecting cable 5 Please use extension cable if the distance between wired remote controller and indoor unit is more than 10m ACAUTION When installing the wired remote controller do not bury it in the wall It can cause damage in the temperature sensor Do not install the cable to be 50m or above It can cause communication error When installing the extension cable check the connecting direction of the connector of the remote controller side and the product side for correct installation If you install the extension cable in the opposite direction the connector will not be connected Specification of extension cable
46. t of indication window Function Code t During the test run pressing the below button will exit the test run Select operation temperature up down wind flow control wind direction start stop button Owner s amp Installation Manual 11 Installation instruction Installer Setting Setting Addres It s the function to use for connecting central control Please refer to central controller manual for the details If pressing button long for 3 seconds it enters into remote i controller setter setup mode If pressing once shortly it enters into user setup mode Please press 200 more than 3 seconds for sure If entering into address setup mode by using button it indicates as picture below egg Group No aly oa Function Code ji T Indoor No Set Group No by pressing m button 0 F DeFa Move to Indoor No setting option by pressing 9 Dd bution ero T Set Indoor No by pressing v button Per Installer Setting E S P This is the function that decides the strength of the wind for each wind level and because this function is to make the installation easier Installation instruction This setting must be carried out by a certificated technician If you set ESP incorrectly the air conditioner may malfunction 1 If pressing G3 button long for 3 seconds
47. ted Ceiling Height Level Description 01 Low Decrease the indoor airflow rate 1 step from standard level 02 Standard Set the indoor airflow rate as standard level 03 High Increase indoor airflow rate 1 step from standard level 04 Very high Increase indoor airflow rate 2 steps from standard level Ceiling height setting is available only for some products Ceiling height of Very high function may not exist depending on the indoor unit Refer to the product manual for more details 16 New Wide Wired Remote Controller Installer Setting Static Pressur This function is applied to only duct type Setting this in other cases will cause malfunction displays 1 Press button for 4 seconds to enter the installer setting mode until timer segment 01 01 Installation instruction below If pressing 3 button repeatedly it moves to static pressure selection menu as picture oat ie button Pressure static pressure by pressing 01 V H 02 F H 03 V L 04 F L OED C Function Code Press button to save Pressing button will exit settings mode k After setup it automatically gets out of setup mode if there is no button input for 25 seconds k When exiting without pressing set button the manipulated value is not reflected lt Static Pressure Setting Table gt
48. the bottom of the LCD screen me gi gi Function Code Value Some categories of the menu may not be displayed according to the function of the product or the menu name may be different 8 New Wide Wired Remote Controller lt Installer Setting Code Table gt 1 General air conditioner product Installation instruction No Function Code Value 1 Test Run 01 01 Set 2 Address Setting 02 00 FF Address lt ESP Step gt lt ESP Value gt lt Example gt 01 VeryLow 0 255 02 L G30 i Obs 3 E S P Value 03 eia SE a 04 High Function Code ESPstep ESP value 05 Very High 01 Remo 4 Thermistor 04 02 Indoor 03 2TH 01 Med 5 Ceiling Height 05 peri 04 Very High 01 V H 6 Static Pressure 06 STA 04 F L 7 Master Setting 07 renee 8 Override Setting 08 nore 9 Dry Contact 09 SA Release 3 Min 10 Delay 10 01 Set 01 Variable 11 Zone State 11 02 Fixed Celsius 00 Celsius nee 12 Fahrenheit Switching ia 01 Fahrenheit Gliese eM 13 Jone T 43 00 Zone Controller one Type 01 Damper Controller 14 Zone Number 14 02 04 Zone number 15 Plasma 20 16 Electric heater 21 00 Not Installed 17 Humidifier 22 ai i i 7 18 Elevation Grill 23 eee 19 Ventilation Kit 24 Some contents may not be displayed depending on the product function Owner s amp Installation Manual 9 Installation instruction 2 General Ventilation product
49. tting mode When the Hour icon flash please setting time The setting range is within 1 12 rs o 1200 Pgh gt mon On inuu K wes 5 Press lt S button to shift to Minute setting mode When the Minute icon flash please setting minute the setting range is within 00 59 50 New Wide Wired Remote Controller Owner s instruction Press button to exit After setup it automatically gets out of setup mode if there is no button input for 25 seconds When exiting without pressing set button the manipulated value is not reflected If reservation is set turned off indication shows up at the lower part of LCD screen and air conditioner product runs at the time that is set If reservation is cancelled turned off indication disappears Owner s amp Installation Manual 51 Owner s instruction Programming Weekly Reserva You can set the daily reservation in weekly unit Weekly reservation keeps operating until before you cancel it once you setup Please move to reservation setup mode by pressing reservation button 3 You can setup two weekly reservations for one day and up to fourteen reservations for a week For example to setup Tuesday morning 11 30 turned on afternoon 12 30 turned off you setup in order below Please move to weekly by repeatedly pressing reservation SVAN ce ccry yer pon gu
50. website http www lgservice co LG ONVITVLI IMPORTANT Please read this owner s amp installation manual completely before installing the product Installation work must be performed in accordance with the national wiring standards by authorized personnel only Please retain this owner s amp installation manual for future reference after reading it thoroughly P No MFL62129202 3 7 g m i a fa I v lt e A Sx vu S 3 9 i mp vn New Wide Wired Remote Controller Owner s amp Installation Manual Safety Precaution TABLE OF CONTENTS ll Safety Precaution The installation requires expert skills and it should be installed by the service center or other shops specialized in the installation and recognized by our company For all the problems arising after installation by someone who has no relevant qualifications our company will not provide free service The following safety cautions are provided to prevent unexpected dangers or losses Safety Precautio Part Description Installation instruction Group control Installer Setting How to enter installer setting mod Installer Setting Test Run Mode Installer Setting Setting Address of Central Control AAWARNING If the user does not follow the mandatory items it may result in serious injury or death Installer Setting E S P Installer Setting Thermistor ACAUTION If t
51. wner s amp Installation Manual 41 Owner s instruction Function Setting Change Temp Change temperature is the function to setup air cooling and heating drive automatically changeable according to the temperature at artificial intelligence drive mode Repeat pressing button until Qr icon flash Converting temp value 1 7 bd Press button to complete and active the setting process g Press button to exit or system will automatically release without any input after 25 seconds 3k When exiting without pressing set button the manipulated value is not reflected 42 New Wide Wired Remote Controller Owner s instruction Function setting Changing Curr 1 Please press function setup button If pressing function setup button repeatedly it moves to time setup menu Time setup icon is indicated at that time and date blinks at current time indication area Ex Changing Current Time as Monday AM 10 20 gt key to adjust the current 3 Press key to move to AM PM setting mode the AM PM segment will flash A om2ng ae me Setting AM PM value by pressing button g 5 Press lt button to move to Hour setting mode the Hour segment wil flash A_ o legg iN 6 Setting Hour value by pressing A button

LG New Wide Wired Remote Controller - LG Duct-Free

Contents

Download Pdf Manuals

Related Search

Related Contents