GOT-5120T-830
Contents
1. IK AXIOMTEK GOT 5120T 830 All in One 12 1 SVGA TET Fanless Touch Panel Computer with Intel Atom N270 Processor Onboard User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2009 AXIOMTEK Co Ltd All Rights Reserved August 2009 Version A1 Printed in Taiwan Safety Approvals CE Marking ECC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are meant to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instru2. AMI BIOS Setup Utility 35 GOT 5120T User s Manual APM Configuration You can use this screen to select options for the APM Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Power Management APM Enabled 36 gt Power Management APM Set this item to allow Power Management APM support The default setting is Enabled Set this item to prevent the chipset power management and APM Advanced Power Management features Set this item to allow the chipset power management and APM Advanced Power Management features This is the default setting gt Video Power Down Mode This option specifies the Power State that the video subsystem enters when the BIOS places it in a power saving state after the specified period of display inactivity has AMI BIOS Setup Utility GOT 5120T User s Manual expired The default setting is Suspend This setting prevents the BIOS from initiating Disabled any power saving modes concerned with the video display or monitor This option places the monitor into suspend mode after the specified period of display inactivity has expired This means the monitor is not off The screen will appear blacked out The standards do not cite specific power ratings because they vary from monitor to monitor but this setting use less power than Standby mode This is the default setting gt
3. Hard Disk Drive Power Down Mode This option specifies the power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired The default setting is Suspend Disabled This setting prevents hard disk drive power down mode This option cuts the power to the hard disk drives during a system suspend This is the default setting gt Suspend Time Out Minute This option specifies the length of time the system waits before it enters suspend mode The default setting is Disabled S This setting prevents the system from entering rags suspend mode This is the default setting Set this item to allow the computer system to enter Suspend mode after being inactive for 1 minute Set this item to allow the computer system to enter suspend mode after being inactive for 4 minutes Set this item to allow the computer system to enter suspend mode after being inactive for 10 minutes gt Throttle Slow Clock Ratio Use this item to specify the speed of the system clock when running the power saving states gt Power Button Mode This option specifies how the externally mounted power AMI BIOS Setup Utility 37 GOT 5120T User s Manual button on the front of the computer chassis is used The default setting is On Off Pushing the power button turns the computer On Off on or off This is the default setting This is the default setting Pushing the power button places the co
4. 1 2 2 1 3 4 5 F WE ECH 51 3 4 COM 1 RS 232 422 485 5 EA RE 8 Ls Introduction 7 GOT 5120T User s Manual 1 5 Packing List When you receive the GOT 5120T 830 the bundled package should contain the following items GOT 5120T 830 x 1 Panel Mount Kit x 6 Driver CD x1 Wall Mount Kit x1 HDD Mylar x 1 Desktop Stand Kit optional VESA ARM optional Power Adapter amp power cord for GOT 5120T 830 J If you can not find the package or any items are missing please contact AXIOMTEK distributors immediately 8 Introduction GOT 5120T User s Manual CHAPTER 2 HARDWARE INSTALLATION The GOT 5120T 830 provides rich I O ports and flexible expansions for you to meet different demand for example CF card The chapter will show you how to install the hardware It includes 2 1 CompactFlash Card Serial Port Ethernet Mounting Way Hard disk Dram Wireless LAN Card CF card Installation The GOT 5120T 830 provides one CF slot for users to install CompactFlash card Please refer to the following instructions for installation Step 1 Turn off the system and unplug the power cord Hardware Installation 9 GOT 5120T User s Manual Step 2 Find out the cover on the side of the system Step 3 Locate the CompactFlash socket and insert the card into the socket 10 Hardware Installation GOT 5120T User s Manual 2 2 Serial Ports Interface The GOT 5120T 830 has t
5. GOT 5120T 830 is designed for panel mount application A set of standard mounting kit are bundled with the system package that you can use it to mount the GOT 5120T 830 14 Hardware Installation GOT 5120T User s Manual 2 4 2 Wall Mounting The GOT 5120T 830 is designed for Wall mounting application Please refer to the following steps Find out the screws as marked on the back side of chassis Hardware Installation 15 GOT 5120T User s Manual 2 4 3 Desktop Mounting The GOT 5120T 830 is designed for desktop mounting application Please refer to the following steps Step 1 Find out the screws as marked on the back side of chassis 16 Hardware Installation GOT 5120T User s Manual Step 2 Assemble the desktop stand to the chassis and fix the Screws Hardware Installation 17 GOT 5120T User s Manual 2 4 4 VESA ARM Mounting Step 1 Find out the screws as marked on the back side of chassis Step 2 Assemble the VESA ARM to the back side of the chassis and fix the screws 18 Hardware Installation GOT 5120T User s Manual Step 3 VESA mounting Installation completed Hardware Installation 19 GOT 5120T User s Manual 2 5 HDD Installation The GOT 5120T 830 provides a convenient Hard Disk Drive HDD bracket for users to install 2 5 SATA HDD Please follow the steps 1 Unscrew eight screws to remove the rear chassis 2 Unscrew 4 screws from the HDD br
6. Manual 3 Security Menu The Security menu allows users to change the security settings for the system BIOS SETUP UTILITY Change Supervisor Password gt Supervisor Password This item indicates whether a supervisor password has been set If the password has been installed Installed displays If not Not Installed displays gt User Password This item indicates whether a user password has been set If the password has been installed Installed displays If not Not Installed displays gt Change Supervisor Password Select this option and press lt Enter gt to access the sub menu You can use the sub menu to change the supervisor password gt Change User Password Select this option and press lt Enter gt to access the sub AMI BIOS Setup Utility 51 GOT 5120T User s Manual 52 menu You can use the sub menu to change the user password gt Boot Sector Virus Protection This option is near the bottom of the Security Setup screen The default setting is Disabled Protection This is the default setting Select Enabled to enable boot sector protection It displays a warning when any program or virus issues a Disk Format command or attempts to write to the boot sector of the hard disk drive If enabled the following appears when a write is attempted to the boot sector You may have to type N several times to prevent the boot sector write Boot Sector Write Possible VIRUS Continue Y N The foll
7. Multiple Monitors Tools About P Penmounk Control Panel Version 1 0 0 19 Installed Device s Device 0 PenMount 6000 USB Support E mail penmoLntiaseed net tw Support Website http Zweig Deppmoupd com ba 62 Installation of Drivers GOT 5120T User s Manual 4 Select the Standard Calibrate tab d Device 0 PenMount 6000 USB Calibrate Setting Edge Compensation Abort Advanced Mode ee ee Flot calibration data Standard calibration Bi ezl was Calibration E a Turn off EEPROM storage 5 Calibration To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration Touch the red square 6 Press OK Installation of Drivers 63 GOT 5120T User s Manual 4 3 Embedded O S The GOT 5840T provides the Windows XP Embedded and Windows CE Net 6 0 The O S is supported devices which are listed below 4 3 1 Windows XP Embedded Here are supported onboard devices Onboard Multi I O SATA HDD USB PS2 Keyboard and mouse CRT LCD display Default 18bits Resolution 800x600 10 100 1000 base T Ethernet Compact Flash Onboard Audio Touch Screen PenMount Touch screen Before you can use and calibrate it here is what you should do 1 Set up Penmount touch device driver by executing C Penmount Windows 2000 XP V5 0 setup exe When the installation is finished an
8. USB 2 0 Ethernet m One RIL81111b Gigabit Ethernet Audio m One Line out Expansion One Mini card Storage m One slot for CF card m One SATA Power connector m GOT 5120T 830 10VDC to 30VDC with phoenix power connector m GOT 5120T 830 J External 60W AC Adapter with screw type connector 1 2 3 System Specification 12 1 TFT LCD Heat Dispensing Design Disk drive housing m One 2 5 SATA drive Net Weight m 2 48 Kgs 5 46 lb Dimension Main Body Size m 328x 262 x 52mm Operation Temperature m OC to 45C Introduction 3 GOT 5120T User s Manual e Relative Humidity m 10 to 90 40 C Non Condensing e Vibration m 5 to 500 Hz 2 0 G random for CF card e Power input m 10 30VDC with phoenix power connector m External 60W AC Adapter Power Input 9OVAC to 264VAC Power Output 12VDC Max 5A X NOTE All specifications and images are subject to change without notice X NOTE f the operation temperature is higher than 35C the wide temperature DRAM and HDD are recommended to be used on the device 4 Introduction GOT 5120T User s Manual 1 3 Dimensions This diagram shows you dimensions and outlines of the GOT 5120T 830 312 00 CUTOUT Dim 290 00 Introduction 5 GOT 5120T User s Manual 6 Introduction GOT 5120T User s Manual 1 4 UO Outlets Please refer to the following illustration for I O locations of the GOT 5120T 830 Ceo Fran
9. card One is MAIN and the other is auxiliary Connect antenna cable to MAIN connector on wireless LAN card i FE l ga ETS a A o Su s E Hardware Installation 25 GOT 5120T User s Manual MEMO 26 Hardware Installation GOT 5120T User s Manual CHAPTER 3 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the AMI BIOS setup utility 2 1 Starting To enter the setup screens follow the steps below 1 Turn on the computer and press the lt Del gt key immediately After you press the lt Delete gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Chipset and Power menus 3 2 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F10 gt lt Enter gt lt ESC gt lt Arrow gt keys and so on W N Note Some of navigation keys differ from one screen to another Left Right The Left and Right lt Arrow gt keys allow you to select a setup screen MV Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen The Plus and Minus lt Arrow gt keys allow you to Plus Minus l i i Change the field v
10. contains several options for your configuration PCIE Port 0 Auto AMI BIOS Setup Utility 41 GOT 5120T User s Manual e USB Configuration You can use this screen to select options for the USB Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Legacy USB Support Enabled gt Legacy USB Support Use this item to enable or disable support for USB device on legacy operating system The default setting is Enabled gt USB 2 0 Controller Mode Use this item to configure the USB 2 0 controller The default setting is HiSpeed gt BIOS EHCI Hand On Enabling this item provide the support for operating systems without an EHCI hand off feature The default setting is Enabled 42 AMI BIOS Setup Utility GOT 5120T User s Manual 3 5 PCI PnP Menu The PCI PnP menu allows users to change the advanced settings for PCI PnP devices BIOS SETUP UTILITY Clear NURAM AMI BIOS Setup Utility 43 GOT 5120T User s Manual BIOS SETUP UTILITY Reserved Memory Size Disabled 44 gt Clear NVRAM Use this item to clear the data in the NVRAM CMOS Here are the options for your selection No and Yes gt Plug amp Play O S When the setting is No Use this item to configure all the devices in the system When the setting is Yes and if you install a Plug and Play operating system the operating system con
11. gt Serial Port IRQ This item specifies the IRQ used by the serial port 1 gt Serial Porz Address This item specifies the base I O port address and Interrupt Request address of serial port 2 The Optimal setting is 2F8 IRQ3 The Fail Safe setting is 2F8 gt Serial Port2 IRQ This item specifies the IRQ used by the serial port 2 AMI BIOS Setup Utility GOT 5120T User s Manual gt Serial Port3 Address This item specifies the base I O port address and Interrupt Request address of serial port 3 gt Serial Port3 IRQ This item specifies the IRQ used by the serial port 3 gt Serial Port4 Address This item specifies the base I O port address and Interrupt Request address of serial port 4 gt Serial Port4 IRQ This item specifies the IRQ used by the serial port 4 AMI BIOS Setup Utility 33 GOT 5120T User s Manual e Hardware Health Configuration This screen shows the Hardware Health Configuration and a description of the selected item appears on the right side of the screen BIOS SETUP UTILITY gt System Temperature CPU Temperature These items display the temperature of CPU and System Vcore etc 34 AMI BIOS Setup Utility GOT 5120T User s Manual e ACPI Settings You can use this screen to select options for the ACPI Settings and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY K Suspend mode 1 POSI
12. icon PM appears on the Taskbar Calibrate Penmount touch by clicking on the PM icon and the go on the calibration Restart the computer Installation of Drivers GOT 5120T User s Manual 4 3 2 Windows CE NET 6 0 Here are supported onboard devices s Onboard Multi I O s SATA HDD s USB s PS2 Keyboard and mouse s CRT LCD display a 10 100 1000 base T Ethernet s Compact Flash s Onboard Audio a Audio e Touch Screen Calibration Touch screen In this image we add PenMount Touch drivers and utilities It is customized for 800 x 600 Calibration 1 Click Calibratyion on desktop to calibrate touch screen 2 Inthe start programs menu select save registry thus Calibration data will be saved and effective in next booting Installation of Drivers 65
13. 54 AMI BIOS Setup Utility GOT 5120T User s Manual BIOS SETUP UTILITY DUMT Mode Select DUMT Model AMI BIOS Setup Utility 55 GOT 5120T User s Manual e South Bridge Configuration BIOS SETUP UTILITY USE Functions Enabled 56 AMI BIOS Setup Utility GOT 5120T User s Manual BIOS SETUP UTILITY gt USB Function This item allows you to enable or disable USB function gt USB 2 0 Controller This item allows you to enable or disable the USB 2 0 controller gt Audio Controller This item allows you to enable or disable the audio support gt SLP_S4 Min Assertion Width This item allows you to set the SLP_S4 Assertion Width gt Restore on AC Power Loss This item can control how the PC will behave once power is restored following a power outage or other unexpected shutdown gt PCIE Port Configuration AMI BIOS Setup Utility 57 GOT 5120T User s Manual This item allows you to set or disable the PCI Express Ports 3 9 Exit Menu The Exit menu allows users to load your system configuration with optimal or failsafe default values 0 BIOS SETUP UTILITY save Changes and Exit 58 gt Save Changes and Exit When you have completed the system configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Exit from the Exit menu and press lt Enter gt Select Ok to save changes an
14. acket and take out HDD bracket 20 Hardware Installation GOT 5120T User s Manual 3 Screw the 2 5 HDD together with the HDD Mylar to the HDD bracket 4 Fix the HDD bracket into the system and plug the data and power cable to HDD Installation complete Ki Lnn Hardware Installation 241 GOT 5120T User s Manual 2 6 DRAM Installation The GOT 5120T 830 provides one 200 pin DDR2 SODIMM socket that support system memory up to 2GB Please follow steps below to install the memory modules 1 Open the back cover and find mainboard SBC8 7830 22 Hardware Installation GOT 5120T User s Manual 3 Install the memory module into the socket and push it firmly down until it is fully seated The socket latches are levered upwards and clipped on to the edges of the DIMM E TT 7 s c d AOC 3 KS ate d A Hardware Installation 23 GOT 5120T User s Manual 2 Wireless LAN Card Installation The GOT 5120T 830 provides one Mini card slot for user to install one wireless LAN card When installing the wireless LAN card refer to the following instructions and illustration 1 Open the back cover and find mainboard SBC8 7830 2 The socket latches are clipped on to the edges of the Mini card Install wireless LAN card to the socket 24 Hardware Installation GOT 5120T User s Manual 3 Find the built in Antenna cable 4 There are two connectors on wireless LAN
15. alue of a particular setup item Tab The lt Tab gt key allows you to select setup fields The lt F1 gt key allows you to display the General Help screen AMI BIOS Setup Utility 27 GOT 5120T User s Manual The lt F10 gt key allows you to save any changes you have made and exit Setup Press the lt F10 gt key to save your changes The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the lt Esc gt key to exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens 3 3 Main Menu When you first enter the Setup Utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab There are two Main Setup options They are described in this section The Main BIOS Setup screen is shown below BIOS SETUP UTILITY systen Time te AUS len e System Time Date Use this option to change the system time and date Highlight 28 AMI BIOS Setup Utility GOT 5120T User s Manual System Time or System Date using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Arrow gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format 3 4 Advanced Menu The Adva
16. assis for a few seconds This will help to discharge any static electricity on your body When handling boards and components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Atom are registered trademarks of Intel Corporation MS DOS Microsoft C and Quick BASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents Be File ii EEN li Safely Precautions ebe iv CHAPTER 1 INTRODUCTION sss sss sss sss sss sss sss 1 1 1 General Description 1 1 2 Tee e E 2 ter Man e S B B lt e Le EE 2 122 He EE 3 1 2 3 System Specification cccccccccccessssseeeeeeeeeeeeeeenens 3 1 3 DIMENSIONS EE 5 1 4 VO OUIS naie A 7 1 5 FACKING H leenan techies eauness 8 CHAPTER 2 HARDWARE INSTALLATION 9 2 1 GF card IMstallatioN steere 9 2 2 Serial Ports Interface sione i 11 2 3 Se e 12 2 4 Mountings Panel Wall Desktop VESA sss ss 14 241 lt TTS eis lt ed 14 242 WWAIRWMOUNTING otidect eege 15 2 4 3 Desktop MOunting ccc
17. ccscccssssseceessssseeesseseseeseees 16 2 4 4 VESA ARM Mounting sss sese eee eee eee eee 18 2 5 FAD LD ISLAM ANON EE 20 2 6 DRAM Installation s sse eee eee eee 22 2 7 Wireless LAN Card Installation sss eee eee 24 CHAPTER 3 AMI BIOS SETUP UTILITY 27 3 1 EH 27 3 2 Navigation EE 27 3 3 VEIREL 28 3 4 Advanced Men 29 3 5 Reha Laat MENU EE 43 3 6 EGG NIG A a A 46 3 7 EEN MENU sroin dee deet ege Ee 51 3 8 G hipset Mentse 53 3 9 FALMER Usa aceon Sverseiaueieetpamveri 58 vi 4 1 4 2 4 2 1 4 2 2 4 3 4 3 1 4 3 2 OY SLC EE 60 TOUCH SOEC DEE 61 SPECHICALON ME 61 Driver Installation Windows AH 61 Embedded Bie tne nee oe ee ee rr 64 Windows XP Embedded s ssnsenenseneenenennrnnrnnnnn 64 Windows GE NEN EE 65 Vil MEMO viii GOT 5120T User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the GOT 5120T 830 Chapter 1 includes the following sections General Description Specification Dimensions UO Outlets Package List 1 1 General Description The GOT 5120T 830 is a fan less and compact size touch panel computer equipped with a 12 1 TFT LCD display and low power consumption Intel Atom H N270 1 6GHz processor with FSB 533MHz The GOT 5120T 830 supports Windows XP Windows CE NET and Windows XP embedded The panel computer is able to install a CompactFlash card and provide a Mini card slot for wireless mod
18. ctions this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following methods esch Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment to another outlet of a circuit that doesn t connect with the receiver 4 Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with the emission limits Safety Precautions Before getting started please read the following important safety precautions The GOT 5120T 830 does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cord from the GOT 5120T 830 before any installation Be sure both the system and ext
19. d exit gt Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration Select Discard Changes and Exit from the Exit menu and press lt Enter gt Select Ok to discard changes and exit gt Discard Changes AMI BIOS Setup Utility GOT 5120T User s Manual Use this item to abandon all changes gt Load Optimal Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Optimal settings are designed for maximum system performance but may not work best for all computer applications In particular do not use the Optimal Setup options if your computer is experiencing system configuration problems Select Load Optimal Defaults from the Exit menu and press lt Enter gt gt Load Fail Safe Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Fail Safe settings are designed for maximum system stability but not maximum performance Select the Fail Safe Setup options if your computer is experiencing system configuration problems Select Load Fail Safe Defaults from the Exit menu and press lt Enter gt Select Ok to load Fail Safe defaults AMI BIOS Setup Utility 59 GOT 5120T User s Manual CHAPTER 4 DRIVERS INSTALLATION 4 1 System GOT 5120T 830 supports Windows 2000 XP To facilitate the installation of system driver please car
20. efully read the instructions in this chapter before start installing 1 Insert Driver CD and select the Drivers kd bP e step 1 step Z step 3 Chipset WA Ethernet G bP LC Step4 Step5 Step Audio Touch Wireless LAN 3 2 Select all files and follow the installing procedure 60 Installation of Drivers GOT 5120T User s Manual 4 2 Touch Screen The GOT 5840T 830 uses the 5 wire analog resistve There are the specification and driver installation which are listed below 4 2 1 Specification 5 wire Analog Resistive type Touch Screen Controller PenMount 6000 USB Touch Screen Controller IC Baud Rate 19200 baud rate fixed 1024 x 1024 10 bit A D converter inside BV Power Input EEN Active 24 6mA Idle Mode 13 4mA 4 2 2 Driver Installation Windows XP The GOT 5120T 830 provides a touch screen driver that users can install it under the operating system Windows XP To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation 1 Insert Driver CD and follow the path to select the Drivers Step 5 Touch Windows Universal Driver 2 1 0 234 2 Follow the installing procedure and press OK Installation of Drivers 61 GOT 5120T User s Manual 3 Click Start menu and select PenMount Utilities and then a PenMount Control Panel pops out PenMount Control Panel Device
21. er on state for the NumLock The default setting is On gt PS 2 Mouse Support This item determines if the BIOS should reserve IRQ12 for the PS 2 mouse or allow other devices to make use of this AMI BIOS Setup Utility 47 GOT 5120T User s Manual IRQ Here are the options for your selection Auto Enabled and Disabled gt Wait For F1 If Error If this item is enabled the system waits for the F1 key to be pressed when error occurs The default setting is Enabled gt Hit DEL Message Display If this item is enabled the system displays the message Press DEL to run Setup during POST The default setting is Enabled e Boot Device Priority The Boot Device Priority screen specifies the the boot device priority sequence from the available devices BIOS SETUP UTILITY ist Boot Device USE Generic STORAG 48 AMI BIOS Setup Utility GOT 5120T User s Manual e Removable Drives Use this screen to view the removable drives in the system The BIOS will attempt to arrange the removable drive boot sequence automatically You can also change the booting sequence BIOS SETUP UTILITY lst Drive USB Generic STORAG AMI BIOS Setup Utility 49 GOT 5120T Users Manual e Lan Boot Settings Configuration The Lan Boot Settings Configuration can enable or disable Lan Boot ROM to allow the system boot on LAN BIOS SETUP UTILITY Lan Boot ROM Disabled 50 AMI BIOS Setup Utility GOT 5120T User s
22. ernal devices are turned OFF A sudden surge of power could ruin sensitive components that the GOT 5120T 830 must be properly grounded The brightness of the flat panel display will be getting weaker as a result of frequent usage However the operating period varies depending on the application environment Turn OFF the system power before cleaning Clean the system using a cloth only Do not spray any liquid cleaner directly onto the screen The GOT 5120T 830 may come with or w o a touchscreen Although the touchscreen is chemical resistant it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen In case your system comes without the touchscreen you must follow the same procedure and not spray any cleaner on the flat panel directly Avoid using sharp objects to operate the touchscreen Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen The flat panel display is not susceptible to shock or vibration When assembling the GOT 5120T 830 make sure it is securely installed Do not open the system s back cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions Before handling a board or integrated circuit touch an unpainted portion of the system unit ch
23. figures the Plug and Play devices not required for boot The default setting is No gt PCI Latency Timer This item controls how long a PCI device can hold the PCI bus before another takes over The longer the latency the longer the PCI device can retain control of the bus before handing it over to another PCI device There are several options for your selection gt Allocate IRQ to PCI VGA This item allows BIOS to choose an IRQ to assign for the PCI VGA card Here are the options for your selection No AMI BIOS Setup Utility GOT 5120T User s Manual and Yes gt Palette Snooping Some old graphic controllers need to snoop on the VGA palette and then map it to their display as a way to provide boot information and VGA compatibility This item allows such snooping to take place Here are the options for your selection Disabled and Enabled gt PCIIDE BusMaster This item is a toggle for the built in driver that allows the onboard IDE controller to perform DMA Direct Memory Access transfer Here are the options for your selection Disabled and Enabled gt OffBoard PCI ISA IDE Card This item is for any other non onboard PCI ISA IDE controller adapter There are several options for your selection gt 1RQ3 4 5 7 9 10 11 14 15 These items will allow you to assign each system interrupt a type depending on the type of device using the interrupt The option Available means the IRQ is going to assign au
24. mputer in Suspend mode or Full On power mode Advanced Resume Event Controls gt Resume On Ring This item enables or disables the function of Resume On Ring that resumes the system through incoming calls gt Resume On RTC Alarm You can set Resume On RTC Alarm item to enabled and key in Data time to power on system 38 AMI BIOS Setup Utility GOT 5120T User s Manual e MPS Configuration This screen shows the MPS Multi Processor Specification Configuration and you can change its value A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY MPS Revision gt MPS Revision Use this item to select MPS Multi Processor Specification Revision 1 1 or 1 4 The default setting is 7 4 AMI BIOS Setup Utility 39 GOT 5120T User s Manual e PCI Express Configuration This screen shows the PCI Express Configuration and you can change its value A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Active State Power Management Disabled gt Active State Power Management Use this item to enable or disable the function of Active State Power Management to provide you with lower power consumption The default setting is Disabled 40 AMI BIOS Setup Utility GOT 5120T User s Manual gt B PCIE Ports Configuration Scroll to this item and press lt Enter gt to view the SB PCIE Ports Configuration sub menu which
25. nced menu allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the screen to go to the sub menus e CPU Configuration e IDE Configuration e SuperlO Configuration e Hardware Health Configuration e ACPI Configuration e APM Configuration e MPS Configuration e PCI Express Configuration e USB Configuration For items marked with gt please press lt Enter gt for more options BIOS SETUP UTILITY CPU Configuration AMI BIOS Setup Utility 29 GOT 5120T User s Manual e Configure advanced CPU settings This screen shows the CPU Configuration and you can change the value of the selected option BIOS SETUP UTILITY Max CPUID Value Limit Disabled gt Max CPUID Value Limit You can enable this item to let legacy operating systems boot even without support for CPUs with extended CPU ID functions gt Execute Disable Bit Capability This item helps you enable or disable the No Execution Page Protection Technology gt Hyper Threading Technology Use this item to enable or disable Hyper Threading Technology which makes a single physical processor perform multi tasking function as two logical ones gt Intel R SpeedStep tm tech This item helps you enable or disable the Intel SoeedStep Technology gt Intel R C STATE tech Use this item to enable or disable the C State technology 30 AMI BIOS Setup Utility GOT 5120T User s Ma
26. nual gt Enhanced C States This item allows you to enable or disable any available enhanced C states C1E C2E C3E C4E and Hard C4E e IDE Configuration You can use this screen to select options for the IDE Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen For items marked with gt please press lt Enter gt for more options BIOS SETUP UTILITY ATA IDE Configuration Compatible gt ATA IDE Configuration Use this item to specify the integrated IDE controller There are three options for your selection Disabled Compatible and Enhanced gt Legacy IDE Channels When the ATA IDE Configuration is set to Compatible this item will be displayed gt Primary Secondary Third IDE Master Slave Select one of the hard disk drives to configure IDE devices installed in the system by pressing lt Enter gt for more options AMI BIOS Setup Utility 31 GOT 5120T User s Manual SuperlO Configuration You can use this screen to select options for the SuperlO Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen BIOS SETUP UTILITY Serial Porti Address 32 gt Serial Port Address This item specifies the base I O port address and Interrupt Request address of serial port 1 The Optimal setting is 3F8 IRQ4 The Fail Safe default setting is 3F8
27. owing appears after any attempt to format any cylinder head or sector of any hard disk drive via the BIOS INT 13 Hard disk drive Service Format Possible VIRUS Continue Y N Enabled AMI BIOS Setup Utility GOT 5120T User s Manual 3 8 Chipset Menu The Chipset menu allows users to change the advanced chipset settings You can select any of the items in the left frame of the screen to go to the sub menus e North Bridge Configuration e South Bridge Configuration For items marked with gt please press lt Enter gt for more options BIOS SETUP UTILITY K North Bridge Configuration AMI BIOS Setup Utility 53 GOT 5120T User s Manual e North Bridge Configuration BIOS SETUP UTILITY DRAM Frequency E l gt DRAM Frequency This item allows you to control the Memory Clock gt Configure DRAM Timing by SPD This item can enable or disable DRAM timing by SPD Serial Presence Detect device which is a small EEPROM chip on the memory module containing important information about the module speed size addressing mode and various parameters gt Boot Graphic Adapter Priority This item allows you to select the graphics controller as the primary boot device gt Internal Graphics Mode Select This item allows you to select the amount of system memory used by the internal graphics device gt Video Function Configuration Press lt Enter gt for the sub menu for setting up video function
28. tomatically Here are the options for your selection Available and Reserved gt DMA Channel 0 1 3 5 6 7 These items will allow you to assign each DMA channel a type depending on the type of device using the channel The option Available means the channel is going to assign automatically Here are the options for your selection Available and Reserved AMI BIOS Setup Utility 45 GOT 5120T User s Manual 3 6 Boot Menu The Boot menu allows users to change boot options of the system You can select any of the items in the left frame of the screen to go to the sub menus e Boot Settings Configuration e Boot Device Priority e Removable Drives Lan Boot Settings Configuration For items marked with gt please press lt Enter gt for more options BIOS SETUP UTILITY K Boot Settings Configuration 46 AMI BIOS Setup Utility GOT 5120T User s Manual Boot Settings Configuration BIOS SETUP UTILITY Quick Boot Enabled gt Quick Boot Enabling this item lets the BIOS skip some power on self tests POST The default setting is Enabled gt Quiet Boot Set this item to allow the computer system to display the POST messages Set this item to allow the computer system to display the OEM logo This is the default setting gt AddOn ROM Display Mode This item selects the display mode for option ROM The default setting is Force BIOS gt Boot Num Lock Use this item to select the pow
29. ule Its excellent ID and friendly user interface make ita professional yet easy to use panel computer The GOT 5120T 830 is an ideal for space limited applications in factory automation machine maker operating systems building automation and more e GOT 5120T 830 12 1 TFT SVGA Fanless Touch Panel Computer gt Reliable and Stable Design The GOT 5120T 830 adopts a fanless cooling system and a Introduction 1 GOT 5120T User s Manual CompactFlash TM card which makes it suitable for vibration environments Embedded O S Supported The GOT 5120T 830 not only supports Windows XP but also supports embedded OS such as Windows CE NET and Windows XP embedded For storage device the GOT 5120T 830 supports CompactFlash M card and 2 5 SATA device Industrial grade Product Design The GOT 5120T 830 has an incredible design to be used in different industrial environments The front bezel meets the IP65 NEMA4 standard For connecting other devices the GOT 5120T 830 also features several interfaces USB Ethernet and RS 232 422 485 1 2 Specifications 1 2 1 Main CPU Board CPU m Intel Atom N270 1 6GHz processor with FSB 533MHz onboard System Chipset m 945GSE ICH7M BIOS m America Megatrends BIOS System Memory m One 200 pin DDR2 SO DIMM socket Maximum memory up to 2GB Introduction GOT 5120T User s Manual 1 2 2 UO System Standard I O m One RS 282 and one RS 232 422 485 Four
30. wo onboard serial ports COM1 RS 232 422 485 and COM2 RS 232 The following table shows you the pin assignments of this connector 1 data Carer Deteci 060 6 DataSet Ready OSA a irmoa x0 O foreros Ts 4 Data Terminal Ready OTA o Ring macore 5 Grouna noy EP lg 0000 elle In addition COM1 can be set for RS 232 422 485 by jumper The jump setting is listed as below Sa 4 OO Hoa G 4 3 Hardware Installation 11 GOT 5120T User s Manual When COM1 is set to RS 422 or RS 485 the pin assignments are listed below Signal Name RS 422 JL RS 485 DATA DATA No connector No connector No connector GND No connector No connector 7 No connector No connector No connector No connector GND GND 12 Hardware Installation GOT 5120T User s Manual 2 3 Ethernet The GOT 5120T 830 is equipped with a high performance Plug and Play Ethernet interface full compliant with IEEE 802 3 standard and can be connected with a RJ 45 LAN connector Please refer to detailed pin assignment list below TX Data transmission positive TX Data transmission negative Rx Data reception positive 6 Rx Data reception negative 8 Lg termination Hardware Installation 13 GOT 5120T User s Manual 2 4 Mountings Panel Wall Desktop VESA There are several mounting ways for the GOT 5120T 830 Panel Wall Desktop and VESA mountings 2 4 1 Panel Mounting The
Download Pdf Manuals
Related Search
GOT 5120T 830